Try it! You ll like it!

Similar documents
Scout Skills Lashings

Square Diagonal Tripod Japanese Square Filipino Diagonal Round Shear Ladder

Level Two Green Rope. Clove Hitch

requirement 9 Polyester Nylon

Start by crossing the two sticks or dowels at perpendicular or 90 degree angles.

ROYAL CANADIAN AIR CADETS PROFICIENCY LEVEL FOUR INSTRUCTIONAL GUIDE SECTION 3 EO M TIE KNOTS AND LASHINGS PREPARATION

Scout Meeting Schedule: Week 3 Theme: Pioneering A Date:

Scout It Out would like to extend its gratitude to all the sites where the following information had been gathered.

NOTES: Information Booklet 3. Basic Pioneering. Compiled For Cambridgeshire Scouts September2013

Ropework. Stopper Knots. Overhand Knot ROPEWORK. Figure of Eight 3.

Knot Masters Program

Scout Meeting Schedule: Week 2 Theme: Pioneering A Date:

Ropework. Stopper knots. Overhand Knot ROPEWORK. Figure of Eight 3.

Troop 226. Knot Master Program

The loom consists of a row of vertical posts spaced evenly apart. This is the width you require.

Pioneering Challenge. Pioneering Challenge. Tower. Notes: various depending on design points. Project: Walkway.

The Forest School Training Co. OCN accredited training

Pioneering. It s More Than Just Knots and Rope

Troyer s Gourd Rack 8 unit F R H O P

Pioneering. It s More Than Just Knots and Rope

Level Three Blue Rope

Knots and Hitches. To make a reef knot: Check out this video:

Scout Meeting Schedule: Week 1 Theme: Pioneering A Date:

Basket for Janice. by Beth Hester. GH Productions, Inc. The Basket Maker s Catalog

March 2006 Capital District Roundtable PIONEERING. Chris D Garvin Roundtable Commissioner

KNOTS. A very short guide to knotting terminology used on these pages.

Wooden Dummy Construction

1. The Bowline. 2. The Square Knot. 3. The Sheet Bend. My Survival Alliance Volume #1 Issue #24 Page: Continue Inside

Information Booklet 3

ALAMAR KNOT. [Sterp 2] [Step 1] Double the strand as shown. [Sterp3]

KNOTS. Overhand Knot. Page 12 of 32

Swing Your Partner. by Beth Hester. GH Productions, Inc. The Basket Maker's Catalog

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift

End. Standing Part. An underhand loop is made by crossing the end under the standing part.

Skills Night 2005 Troop 80, B.S.A.

knot_craft.doc 1 of 16 Last Updated 2-Sep-08

Melon-Shaped Egg Basket

Tripod Setup Guide (M-TPx)

Knots. Some points on ropes:

Scout. Knot Master. Guide

ESCONDIDO FIRE DEPT TRAINING MANUAL Section Truck Module Page 1 of 13 Ropes Equipment Aloft Revised

MINI-CAMPOREE April, TROOP 80, B.S.A All Rights Reserved. Page 1

Building a 30 Tall Four-Legged Signal Tower

Knots for Cavers Knots, Hitches, Bends, and Splices Step By Step Instructions For tying knots for Caving

Deluxe Gourd Racks I D E G A. Parts List. Shown above are parts for the two-level, Deluxe Gourd Rack (DGR 12V)with 12 arms for vertically hung gourds.

Splicing Instructions. Standard Double Braid Eye Splice Type 1 Double Braid Ropes

Knots, Hitches and Bends

Knots & Their Uses. there are different knots for different purposes and all knots are not good for all purposes practice makes perfect

Safety System Installation Guide for ARE Wind Poles

Middle California Region USPC Preparing For Your C3 Test Bandaging

TENNESSEE COMMISSION ON FIRE FIGHTING

NAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS

Apple Basket with Swing Handle

RATLINER Assembly Instructions.

FALL CAMPOREE. Boy Scout Troops

Parts of a Rope 1. Carrick Bend 2 Fisherman s Bend 4 Hunter s/rigger s Bend 5 Sheet Bend 7

What Knot to Use in a Primitive Situation

Beginners Fly-Tying Notes

FISH NET REPAIR. By Alfred Carlson

SECTION V. Terminology: Bight: Double Bight: Loop: Turn: Round Turn: Half Hitch: Girth Hitch: Running End: Standing End:

Rigging. Student Booklet

Ropework & Securing Loads

Army Mountain Warfare School Ethan Allen Firing Range Jericho, VT Military Mountaineer Course Knot Guide

Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS

Macrame. Knots and Projects

Nice. Nine. Need to. You

Make Your Own Bundled canes Revision Date: May 2014

For Review Only No Copying No Saving No Lending No Posting Online

A Foundation Of Trust. Hanging By A Thread

Beginners/Basic Fly Tying Course

Raft Building Designs

ESCONDIDO FIRE DEPT TRAINING MANUAL Section Truck Module Page 1 of 8 Ropes - Knots Revised

STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING

Installation Instructions for the AlphaDeck Staging System

The Agility Association of Canada

CSK013. Knots Games. 3rd Poole Sea Scouts

Splicing Instructions. Moran Tuck Splice

How Do I Install My Garden Master Bucket Garden?

Keep these things in mind when tying your knots:

Daniel Webster Council Historic District Spring Camporee May 2-4, 2014 At Peterson Farm 154 Martin Road Fremont, NH 03044

Installation and Training Manual

Instructions. Follow All Instructions Before Assembling Or Using This Product

The activity is designed to take about an hour start to finish.

Place a rope coil here

BANKSMAN / SLINGER. 1. What is the smallest size diameter of synthetic rope allowed for use as a hand held tagline?

SCRUFFIES NEWS SCRUFFIES SPECIAL RAFT BADGE DAY Anti-Gambling dog, and Pro RAFT advocate creates viable alternative to Horse racing - Raft Racing!!!

BALL STOP INSTALLTION GUIDE

Sea Scout Knots Knots Hitches Splices and Whippings

Thank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step*

Raritan Valley Fall Camporee

Getting started SCOUT ENGINEERING

Rigging it Right. Presented by Ron Barwick Service Manager for Half Hitch Hosted by: Bob Fowler

VERSA BIKE RACK INSTRUCTIONS

LOW ANGLE ROPE RESCUE OPERATIONAL

2018 Osprey Yacht Club

Knots /2017. Camp and Outdoor Curriculum Manual

Pro-Stringer Tennis Quick Start Stringing Instructions

Boat Boat Loader Fitting Instructions

2010 International Snow Science Workshop

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.

Transcription:

083016 1

Lashing is a method used to join together poles (or spars as they are often called) with rope to build camp projects like wash stands, tables, and even a camp shower! Knowing how to attach two pieces of wood together securely and at the proper angle gives you a real advantage in the outdoors. Lashing is a wonderful skill because it is creative, builds teamwork, and provides great satisfaction after the completion of a sturdy and useful lashing project. Lashing has been around for a long time. Early lashing probably involved wrapping a few strips of bark around branches to make a shelter, or using vines to attach a stone to a branch to make an ax. In modern times, the same methods are used, but strips of bark and vines have been replaced with natural and synthetic fiber ropes. We no longer cut or collect branches from the wild. Pioneering is the art of making structures by using lashing. If you are searching the internet for project ideas try using pioneering projects as a search term. Basic knot skills are essential in order to build a sturdy structure. The clove hitch, the square knot (aka: reef knot) are the two knots you must know and be consistent at tying well. Practice these knots until you know them upside down and backwards. Some styles of lashing can use the timber hitch as an alternative to starting a lashing. Clove Hitch Square Knot Timber Hitch Try it! You ll like it! 2

There are several methods of lashing poles together; each method has a specific application to build the strongest project. Most projects will utilize several of these methods. The types include: SQUARE LASHING: This is the most commonly used lashing method. It is used to attach two poles to one another at a 90 angle or very close to that. This form of lashing will keep the two poles from sliding over each other. TRIPOD LASHING: This type is used to bring together three poles to form a tripod. This same kind of lashing can be used for four poles to make a quadpod which is more stable. DIAGONAL LASHING: This type of lashing is used where the poles are at an angle other than 90 and where the poles have to be pulled together or when they tend to spring apart from each other. An example is the cross-brace of a framework. SHEER LASHING: This method is used to join two poles together to form a scissor shape often used for table legs (sheer legs). ROUND LASHING: This method is used to join two poles to make a longer length, for example when making a flagpole. CONTINUOUS LASHING: This method is used to join flat planks (lath) or small poles onto a horizontal surface. This is the last step in building a table top or chair seat. STRONG verses WRONG: Since lashing has been around for so long and is practiced in every country on the planet, there are many different ways to lash. Keep in mind that NO one way is the ONLY way rather judge your technique based on how strong or secure it is and how neat the lashing looks. Keep trying different standard ways until you find a method that works best for you and your project. This trebuchet shows 5 types of lashing: Sheer, Round, Square, Tripod, and Diagonal. The Possibilities are Endless! 3

Poles: As mentioned earlier, harvesting wood from the wilderness does not align with the Girl Scout principles of protecting our natural environment. Therefore, wood used in lashing projects will need to be obtained from lumber or gardening stores. Pine poles are easy to find milled at lumber yards. They are available in a variety of thicknesses (diameter) and lengths. Tree or gardening stakes can be obtained from gardening centers. They come in a variety of lengths and diameters. Make sure they are sturdy enough. Bamboo is light weight and inexpensive. It can handle vertical stress. However, it has a tendency to splinter, has a slick surface and does not have great horizontal strength. Ending with square knots is highly recommended due to the slick surface. PVC pipe is lightweight but is NOT recommended because it is too slick. Keep in mind that materials may be found from recycled sources like an old broom handle or closet pole. For a typical camp project poles usually vary in length from 2-10 feet. Depending on the strength needed, the diameter of the poles generally ranges from ¾ to 3 inches. Rope: The size and length of the rope you need are among the first questions you have to answer. Braided rope from 1/8 to 3/16 inches in diameter is recommended and can be purchased inexpensively. To determine the length of rope needed for each lashing, add the diameters (in inches) of the two poles at the point the lashing is being made. For example, if one pole is 3/4 inches in diameter and the other is 2 inches in diameter, the total equals 2.75 inches. Multiply this total by 3 to calculate the length of the rope (in feet) needed (2.75 X 3 = 8.25 feet or 8 feet plus 3 inches). The thicker the rope you use, the longer it needs to be. It is better to err on the long side when making lengths of rope. Excess rope can usually be used for additional wraps and fraps or it can be wound around the pole. However, if your rope is too short, you may connect two lengths of rope using a square knot. For safety, don t leave the lashing short; always have a minimum of 3 wraps and 3 fraps. Note: Many Service Units have lashing supplies in their equipment stores. Check to see if you can borrow materials as opposed to purchasing them. Being competent in tying square and clove hitch knots is the first step. As an introduction to lashing, miniature scaled projects can be taught/built using short ( 1.5 ft.) dowels and smaller diameter rope. Begin by teaching the square and tripod lashing methods; these are the two most functional types. Focus on neatness of the wraps and fraps, not speed. Girls can work on a table or the floor in pairs. Teach one type of lashing at a time, allowing them to feel confident before moving to the next type. 4

SQUARE LASHING: This is the most commonly used lashing method. It is used where the poles will try to slide over each other and are at 90 or very close to that. Learn how to square lash: 1. Begin with a clove hitch underneath the pole to be supported (figure 1). Leave enough of a tail (standing end) to tie a squre knot when lashing is complete. Alternatively, end with a clove hitch as shown in Figure 5. 2. Position the horizonal pole above the clove hitch. 3. Wrap the rope up over the horizonal pole, then across behind the vertical pole, pulling tight all the time (figure 2). 4. Next bring the rope down over the horizontal pole then across behind the vertical pole. This finishes one complete wrap (figure 2). Continue wrapping in the same way making sure your rope sits on the outside of the previous wrap. The wraps should not overlap so the rope won t slip and loosen the lashing. All wraps should be neat, even, and tight. 5. After 3-4 wraps, next frap ~3 times. Frapping is when you wind the rope between the poles, pulling tightly each time you go around. This tightens the rope turns already made even tighter, preventing the poles from moving (figure 3 & 4). 6. Finish off with a square knot using the standing end or with a clove hitch (figure 5). 1 2 3 4 5 Example Project: Fire Bucket Holder Here are the suggested materials: one 4-foot x 2-inches stake two 2-foot x 1-inches straight poles Three 9-foot x ~5/32 diameter lashing ropes 5

TRIPOD LASHING (AKA: Figure of Eight lashing): This method is used to bring together three poles to form a tripod. There are several ways to lash a tripod. Below is the most common and effective method. Learn how to tripod lash: 1. Lay 3 poles side-by-side. If poles vary in length be sure to have the butt ends aligned. 2. Start with a clove hitch on one of the outside poles. (figure 1) 3. Coninue with 4-6 turns over and under the poles not too tightly; in a figure of eight pattern. (figure 2 & 3) 4. Make ~3 frapping turns between each pole. (figure 4 & 5) 5. Finish with a square knot using the standing end of the original clove hitch. 6. Alternatively, some end the lashing with a clove hitch instead of a squre knot. Setting up a tripod: 1 Cross the outside poles so that the cross point is under the center pole. This evenly distributes the load via the wood-to-wood contact. 2 3 4 5 NOTE: Tripod lashing that is too tight or has too many wraps may either prevent the tripod from being formed or may overload the rope. In this respect tripod lashing differs from other lashings: it is possible to make it too tight! On occasion, trial and error may be required to obtain the correct tension. 6

DIAGONAL LASHING: This method is used where the poles have to be pulled together or when they tend to spring apart from each other for example in the cross-brace of a framework. Often the two poles form an X and prevent a project from racking. Diagonal lashing should also be used when the angle which the poles are placed is other than 90. Learn how to diagonal lash: Begin with a timber (figure 1) or clove hitch around both poles to draw the poles together. Wrap 3-4 turns around the two poles in one axis (figure 1). Next make 3-4 turns, this time over the center hitch (figure 2). Tighten the turns by applying ~3 frapping turns between the poles, pulling each turn tightly (figure 3). Finish with a clove hitch (figure 4). Alternatively, you may start with a clove hitch around both poles and end with a square knot. 1 2 3 4 Example Project: Wheel Barrow Here are the suggested materials: Four 4-foot x 2-inch poles One 3-foot x 2-inches poles (handle) One 2-foot x 2-inch poles (axle) One wheel Nine 12-foot x ~5/32-inch diameter lashing ropes 7

SHEER LASHING: (sometimes spelled shear ) This method is used to join two poles together to form a scissor shape often used for table legs (sheer legs). With this application the poles might either lift or support weights. Learn how to sheer lash: 1. Line up the two ends of the poles. If poles are of uneven length, align butt ends. 2. Start with a timber (figure 1) or clove hitch around one pole. 3. Continue with 6-8 turns which are made firmly, but not too tight (figure 2). 4. Next, make ~3 frapping turns between the two poles to tighten the lashings (figure 3). 5. Finish with a square knot or clove hitch and spay legs open (figure 4). Note: Sheer legs need to have diagonal support to prevent racking. Figure 1 Figure 2 Figure 3 Figure 4 Example Project: Simple 4 Table Here are the suggested materials: Seven 6-foot x 2-inch poles (legs & stringers) Four 3-foot x 2-inch poles (leg supports) Sixteen 12-foot x ~5/32-inch diameter lashing ropes Two 24-foot x ~5/32-inch diameter lashing ropes (for continuous lashing see pg. 9) Lath material for table top (4-foot X 3-foot) Notice the diagonal rope under the table tied from side-to-side to prevent racking. 8

ROUND LASHING: This method is the most commonly used lashing for extending the length of a pole. Learn how to round lash: 1. Begin with a good overlap of poles; at least a quarter of the total length, better still is an overlap of one third. 2. Start with a clove hitch around both poles near the end of the overlap. 3. Continue with 8-10 tight turns round both poles. 4. Finish with a clove hitch. 5. To tighten, insert small wedges inside the turns; from both above and below. Note: Poles longer than about 2 should add a second lashing to strengthen the overlap so no movement is possible in any direction. (see flagpole below for illustration) Special Note: Unlike all other lashing methods, round lashing has NO frapping turns. The manner in which these lashings are applied results in the poles being in a position where they are already tightly touching. Taking frapping turns between the parallel poles would only weaken the connection. Example Project: Flag Pole Here are the suggested materials: Seven 6-foot x 2-inch poles Nine 12-foot x ~5/32-inch diameter lashing ropes Two 15-foot x ~5/32-inch diameter lashing ropes (guy ropes) One flag, one eye-bolt, and two springloaded clamps 9

CONTINUOUS LASHING: This method takes 3 people and is used to attach flat planks (lath) or small poles onto a horizontal surface. This is the last step in building a table or deck. Learn how to do continuous lashing: 1. Before starting, ensure that the support poles (stringers) are parallel, flat, and that the distance between them is appropriate for the length of the planks. 2. Begin with 2 long lengths of rope; each 6 times the distance that will be lashed. 3. Find the center of each rope and mark with tape or marker. 4. Bundle each half so it can easily be held in the hand. You can wind the rope on a paddle or secure with a loose rubber band (bundle in a way ensuring that the working end slides freely when being pulled/used). 5. Start with a clove hitch in the center of the rope on each stringer pole. a. Note: two girls will work together, each lashing a stringer. The third girl will slide the next lath/pole in place and keep things even. 6. Hold both paddles/bundles of rope, one in each hand like horse reins. 7. Place the first plank and bring both ropes over it. 8. Next, bring ropes under stringer pole and crisscross. 9. Bring ropes back to top and slide in next plank. 10. Continue going over, under, crisscross and up, then sliding in a new plank until continuous lashing is complete. Top View 11. Finish with a square knot using the two ends. underneath View Example Project: Chippewa Kitchen Here are the suggested materials: Six 6-foot x 1-inch poles for tripods Four 8-foot x 1-inch poles for stringers and braces Six 3-foot x 1-inch poles for braces Eighteen 5-foot x 1/8-inch rope Two 40-foot x 1/8-inch rope for continuous lashing Planks for table top (2-foot x 7-foot area) 10

So, now that you have all of the knowledge and have practiced each lashing skill, you can begin building more camp gadgets and even larger campsite improvements. Below are some additional lashing project ideas. The fun, adventure, involvement, and challenges are built right in and also the success... Camp Shower Firewood Shed Picnic Table Low picnic table Chair Tripod Table Drying Rack 3-Sink Dishwashing Station w/ rack 11

Trebuchet what in the world would you do with something like this? 12

Tripod Hand wash Station Even staying clean can be FUN! Tent Three-legged trash bag holder 13

Butt end. The term butt end refers to the end of a pole that will be on the ground. If the pole has a tapered diameter the butt end would be the end with the largest circumference. Frap. A frap is a turn made between the poles. It goes around the wraps to pull the wraps tighter. Lath. Lath is a flat plank of wood often used in continuous lashing to form a table top. Racking. Racking is the undesirable movement of the project from side to side due to insufficient structural support. Spar. A spar is a strong pole used in lashing projects. Sometimes also called a stave (smallest in size). Stake. A stake is a pole with one sharpen end. Used to drive into the ground. Standing end. The standing end (or standing part) of a rope is the part not active in knot tying. It is the part opposite of the working end. Stringer. Stringer refers to two parallel poles that are used as the foundation to attach planks using continuous lashing. Turn. The term turn is often used to describe going around a pole (a wrap). Working end. The working end (or working part) of a rope is the part active in knot tying. It is the part opposite of the standing end. Wedge. A wedge is a small tapered stick that is used to tighten a round lashing. Wrap. A wrap is a turn made around the two poles to hold the poles tightly together. We made it! That s all that matters! 14