ENGLISH AT200 INSTALLATION MANUAL D29020CS416-XXX - SEAT & BOWL COMBINATION-CWH D23020CS11S-XXX - BOWL-CWH D28000AS416-XXX - SEAT / BODY UNIT-CWH Cnvs White (415) Tle of Contents 1. Oserve Listed Preutions for Sfety!... 1 2. Power Supply... 2 3. Wter Pressure... 2 4. Minimum Instlltion Clerne... 2 5. Instlltion position of the remote ontrol... 2 6. Do Not Ple Set Unit on Floor!... 2 7. Notes Prior to Instlltion... 2 8. Prt Desription... 3 9. Prts list... 4 10. Instlltion Proedure... 6 1. Mounting the Toilet Bowl 6 2. Atthing the Wter Shutoff Vlve 11 3. Mounting the Set Unit 13 4. Conneting the Wter Supply Hose (To the set unit) 15 5. Conneting the Wter Supply Hose (To the wter shutoff vlve) 17 6. Conneting to the Power Supply 18 7. Mounting the Remote Control Unit 19 8. Chek for Wter Lekge 21 9. Atthing the Side Covers 22 10. Test Opertion 23 11. If the wter does not flow well, len the striner.... 24 12. To prevent wter from freezing inside this produt, follow the proedure elow to drin the wter.... 25 2014 AS Ameri In.
1. Oserve Listed Preutions for Sfety These sfety preutions re essentil for proper instlltion nd use of the produt. Plese red the preutions thoroughly efore instlling this produt. Explntion of Hzrd Symols WARNING CAUTION Indites potentilly hzrdous sitution whih, if not voided, my result in deth or serious injury. Indites potentilly hzrdous sitution whih, if not voided, my result in minor or moderte injury or dmge to this produt nd other property. WARNING Instll this produt ording to this instlltion mnul. * Improper instlltion my result in eletri shok, fire, injuries, or wter lekge. Do not llow nyone exept n uthorized servie tehniin to disssemle, repir, or modify this produt, s this my use eletri shok, fire, or injuries. Do not pour wter or lening hemils diretly onto the ody or the power plug, s this my use eletri shok or fire. This produt should e grounded, s eletri shok or fire my result. Do not pinh or dmge the power ord, s this my use eletri shok or fire. Do not use loose or ungrounded outlet, s this my use eletri shok or fire. Do not instll this produt in wet or dmp lotion, suh s inside shower room or stem room, s this my led to eletri shok or fire. In order to redue the possiility of skin irrittion, only onnet the produt to potle wter supply line. * The inside of the produt my eome orroded, using n eletri shok, fire, or skin inflmmtion. Do not remove or onnet the power plug with wet hnds, s this my use eletri shok. Do not use this produt with ny power supply other thn 120 VAC. Do not plug ny other pplines into the sme outlet s this produt, s this my led to fire. Firmly onnet the power plug into the outlet, otherwise it my led to eletri shok or fire. CAUTION Flush ny deris inside the toilet's wter supply line prior to onneting the toilet owl. * Dmge inside the produt my result in wter lekge. When removing the striner inside the wter shutoff vlve, mke sure to lose the wter shutoff vlve. When instlling the striner inside the wter shutoff vlve, mke sure tht the wter shutoff vlve is tightened ompletely, s this my result in flooding on the floor. Chek the wter shutoff vlve for lekge fter instlltion, s this my result in flooding on the floor. Cermis re rekle. Prior to instlltion, hek tht there hve een no rekges during trnsporttion. After instlltion, hek tht there hve een no rekges during instlltion. * Dmged portions my use injury, or lekge resulting in flooding on the floor. To the ontrtor: If freezing wether is ntiipted efore hnding this produt over to the ustomer, drin the wter nd leve it, s dmge from freezing my result in flooding on the floor. 1
2. Power Supply Follow the instrutions elow when prepring the eletril outlet for this produt. Amerin Stndrd reommends tht his produt e onneted to GFCI-proteted outlet. Furthermore, it is strongly dvised tht the instlltion of suh n outlet e performed y liensed eletriin. Use 120 VAC power supply with rting of 1300 W. Chek lol eletril odes. Mke sure this produt is grounded orretly. Do not use n extension ord or ny other kind of dpter to onnet this produt to n outlet. The length of the power ord is 3 ft (1 m). The GFCI-proteted outlet should e instlled within reh of the power ord. * Do not onnet the power plug to the outlet until the instlltion is ompleted. Filure to follow this instrution my use the produt to mlfuntion. 3. Wter Pressure Amerin Stndrd reommends minimum wter pressure of 14.5 psi (0.10 MP) flowing t minimum flow rte of 4.8 GPM (18 L/min). 4. Minimum Instlltion Clerne The requried spe nd mount of lerne re shown in the figure elow. * INAX reommends minimum of 2-3/4" (70 mm) or more on eh side of the produt. 5 /8" (15 mm) min. 2 3 /4" (70 mm) min. 2 3 /4" (70 mm) min. 16 3 /8" (415 mm) 15 3 /4" (400 mm) min. 27 1 /2" (700 mm) min. 41 3 /8" (1050 mm) min. Unit: inh (mm) 5. Instlltion position of the remote ontrol On the left side On the right side Within 51 3 /16" (1300 mm) 6. Do Not Ple Set Unit on Floor! Never ple the set unit on the floor, s this my result in rekge of the set unit's mounting olts or wter supply inlet. 7. Notes Prior to Instlltion Instll the remote ontrol on the left wll when fing the toilet unit, so tht it is on the sme side s the remote ontrol signl reeiver s fr s possile. If, for ny hne, the remote ontrol hs to e instlled on the right side, hek if the reeiver will reeive the signl, eforehnd. Moreover, if the wll is some distne wy from the toilet unit, for exmple due to lyout suh s wsh stnd eing instlled etween the wll nd the unit, the signl my not e reeived y the reeiver. If this is the se, eret sreen whih n reflet signls within 51-3/16" (1300 mm) from the enter of the toilet owl. This sreen should e t lest 43-5/16" (1100 mm) in height nd should over the distne etween the signl reeiver nd the remote ontrol s instlled position. (Note tht the onditions my vry little depending on the wll finish nd olor.) Remote ontrol signl reeiver Remote ontrol Do not hold the hose t the rer of the toilet owl. * If the hose is removed, then this my use leks, nd the toilet will not flush properly. Hoses 2
8. Prt Desription m Toilet lid Set unit Flush utton d Side over e Power plug f Wter shutoff vlve g Open/lose hndle d h Wter supply hose i D ryer dut j Nozzle (rer lensing) e i k Nozzle (front lensing) l Toilet owl j k m Remote ontrol n Filter o Drin soket f g h l p Prt numer lel q Mounting se r Mounting fstener (Seuring the toilet owl) n o p q r 3
9. Prts list (hek inside the pkge) A-J indite the steps in the proedure. A Toilet owl Mounting fstener (Atthed to the toilet owl) Bolt (AY-23W) m n o p q r s t v d e f g w j k l h u i d Wsher (lrge) e Ruer tue f Externl tue g Tpered nut h Drin soket i Wx ring j Flnge nut k Wsher (lrge) l T olt m Mounting nut n Wsher (smll) o Bolt (AY-86D) p Wsher (smll) q Sper r Ruer tue s Externl tue t Tpered nut u Instlltion templte v Mounting dhesive w Mounting se 4
B Esutheon ring 2-3/8" 1/2 " MIP nipple Wter shutoff vlve C d d Set unit (ody, toilet set, toilet lid) D g h e f i e Pking wsher f Plsti wsher g Spring wsher h Nut i Wrenh E j k j Clips k Wter supply hose (15 3 / 4 " (400 mm)) G l m l Wll-mount rket * The Wll-mount rket is tthed to the rer of the remote ontrol. Slide it off to remove it. m Remote ontrol n Btteries (2 AAA) o Wood srews n o p p Plsti nhors H q r t u v q Side over (Left) r Side over (Right) s Smll over pnel t Cp u Flt hed srew s w v Coupling wsher w Instrution mnul owner s mnul nd other douments (Atthed to the inside of the toilet lid) 5
10. Instlltion Proedure 1 Mounting the Toilet Bowl 13" (330 mm) 11" (280 mm) 1. Wter Supply Line nd Drin Pipe Lotion The wter supply line nd drin pipe should e loted ording to the digrm on the left. 1/2" wter supply line (from wll) Floor drin 1/2" wter supply line (from floor) 4" (100 mm) 12" (300 mm) or more 12" (300 mm) 11" (280 mm) 4" (100 mm) Before onneting the toilet owl, the wter supply line should e shut off. (for this, INAX reommends the LF-7T) In ddition, the drin pipe should e overed to void sewer gs lekge. 6
d e f g h n i Center of drin soket j k p Ple temporrily n q m o l m l * Mke sure tht the wx ring is tthed to the flnge soket side. 2. Instlling the Drin Soket (1) Temporrily onnet the drin soket to the loset flnge without wx ring. Mrk the lotions of the pilot holes to e drilled. (2) Drill two pilot holes, ø7/16" nd 1-4/5" deep. Clen out the deris from the pilot holes. Insert the tpered nuts, externl tues, nd ruer tues into the pilot holes. (3) Disonnet the drin soket nd tthed the wx ring to the underside of the drin soket. (4) Connet the front of the drin soket to the loset flnge, using the lrge wshers nd flnge nuts. (5) Seure the k of the drin soket to the floor, using the lrge wshers nd olts (AY-23W). d Bolt (AY-23W) e Wsher (lrge) f Ruer tue g Externl tue h Tpered nut i Drin soket j Flnge nut k Wsher (lrge) l Flnge prt m Wx ring n Flnge o Drin outlet p Drin enter line q Soket flnge When onneting the flnge to the drin soket, lign the enter of the flnge with the enter of the drin soket. If the drin soket is not entered, this my led to lokge. Wste Center of flnge Ensure these re prllel When tthing the drin soket to the floor, tke re to void sloping or uneven setions of the floor. Atthing the drin soket kwrds my use inorret flushing or lokge. When seuring the drin soket to the loset flnge, e sure not to over-tighten the nuts. * This my dmge the flnge, using wter lekge. Ensure tht the drin soket is onneted prllel to the rer wll. If this is skewed, the toilet owl will e tthed t n ngle. Pull up d g e f i h Remove [Referene] 1 Ple the ruer tue, externl tue, nd tpered nut in tht order on the olt, nd insert it into the pilot hole. 2 While pushing the end of the ruer in the hole, pull the olt forefully so tht the prts re tightened in the hole. 3 Extrt the olt. Tile Mortr d Conrete e Ruer tue f Externl tue g Tpered nut h Bolt i Atth firmly 7
d e f h g i j k l m n o 3. Atthing the Mounting Bse nd Bolts (1) Align the instlltion templte with the rer edge of the drin soket. Mrk the lotions of the 4 pilot holes to e drilled. (2) Drill 4 ø7/16" holes out 2" deep. Clen out the deris from the pilot holes. Insert the tpered nuts, externl tues, nd ruer tues into the pilot holes. (3) Align the mounting se with the pilot holes t the front of the instlltion templte. Seure this prt using the lrge wshers nd olts. (4) Mount the spers, smll wshers, nd olts to the toilet owl mounting holes. Refer to the digrm t the left for order in whih the prts re instlled. p Bolt (AY-86D) Wsher (smll) Sper d Ruer tue e Externl tue f Tpered nut g Toilet owl mounting hole h Drin soket i Bolt (AY-23W) j Wsher (lrge) k Mounting se l Ruer tue m Externl tue n Tpered nut o Instlltion templte p Mounting se mounting hole Ensure tht there re no shvings or other deris on the mounting se. Crefully remove ny if present, or it my use fulty mounting. 8
Push down using your ody weight d e 4. Seuring the Toilet Bowl (1) As shown in the Fig., ple the mounting dhesive on the mounting se with the uneven portion down. * Ple the mounting dhesive so tht Uneven portion down it will e in the enter of the mounting se. * Prevent moisture or impurities from getting on the mounting dhesive. (2) Aligning the olt of the toilet owl mounting wood srews with the toilet owl mounting holes, insert the drin outlet of the toilet owl into the drin ruer joint of the drin soket, then lign the position with the toilet owl rised to the front. (3) Crefully ple the front of the toilet owl down, joining together the mounting dhesive of the mounting se nd the mounting plte of the toilet owl. (4) Push the front of the toilet down until it touhes the floor. * This ensures tht the toilet owl is firmly onded. (5) Lightly push the toilet owl to mke sure it is firmly tthed. * If the toilet owl is not positioned orretly, lift up the front of the toilet owl, djust, then retth y pressing down. Toilet owl drin outlet Drin soket sleeve Mounting plte (for the toilet owl) d Mounting dhesive e Mounting se 9
(6) Ple the mgi tpe of the side over mounting rkets kit (inluded with the set unit) in the k of the toilet owl so tht its fe is prllel to the toilet owl, nd firmly fsten the wsher nd mounting nut. * The side over mounting rkets kit omes with the side over inluded with the set unit. Clensing wter inlet Mounting nut Wsher (smll) At low tempertures, the mounting dhesive my eome hrd, so wrm nd soften it. * When using wrm wter, put the mounting dhesive in plsti g. Do not ple the set of the toilet owl on the drin soket, s this my dmge the soket or use lekge. Retthing the toilet owl Do not fsten srews on the ermi too tightly, s this my dmge the ermi. Tke re tht the lensing wter inlet is not dmged, or tht deris does not enter. When removing the toilet owl, tke re tht it is not dmged y the fstening srews on its rer. 10
2 Atthing the Wter Shutoff Vlve (1) Deth the open/lose kno. (2) After prepring the wll or floor, tth the 1/2" MIP nipple nd wter shutoff vlve. * When instlling the wter shutoff vlve onto the wter supply pipe, wrp Teflon tpe round the srew threds. * Remove the open/lose hndle from the wter shutoff vlve, nd tighten the vlve s shown in the digrm elow. * Similrly, for floor wter supply, ngle the vlve towrds the wll (pprox. 45 ) for esy onnetion of the wter supply hose. Wll wter supply f 1/2" MIP nipple Approx. 20 Wter supply pipe Teflon tpe g d Adjustment nut e Wter shutoff vlve f Wter supply inlet 4" (100 mm) 11" (280 mm) g Floor h Center line of floor drin e h i Open/lose hndle d i Floor wter supply j j Open/lose hndle k Hexgonl djustment nut k p l Wter shutoff vlve m 1/2" MIP nipple n Wter supply pipe q o Teflon tpe l Approx. 45 p Wter supply inlet q Wll m r Center line of floor drin 4" (100 mm) o 11" (280 mm) r n 11
(3) After tthing the wter shutoff vlve, tth the open/lose hndle. * Chek tht the wter shutoff vlve is losed. Open/lose hndle Positioning slot Clik Do not push or step on the wter shutoff vlve. * The pipe my ome loose, or e dmged, resulting in wter lekge, whih ould dmge wll or rpeting. Atth the wter shutoff vlve wter supply inlet in suh wy tht the wter supply hose is not rimped. «Floor wter supply» If the lotion of the wter supply is on the right when fing the toilet, use n A-6778-62, 25" (620 mm) wter supply hose ville seprtely. 12
3 Mounting the Set Unit Pking wsher Plsti wsher Spring wsher d Nut d (Toilet owl) e 1. Remove the protetive tpe nd protetive p. f Remove the protetive tpe from the toilet owl, nd the protetive p from the set unit. e Plte (Metl) (Rer of set unit) g h f Protetive tpe Do not remove the metl plte. * Wter lekge my result. g Protetive p h Clensing wter inlet (Set unit) i 2. Atth the pking wsher. On the underside of the set unit, ple pking wsher on eh of the mounting olts. * Use the pking wsher to prevent ny dmge to the produt. j i Pking wsher j Mounting olts 13
3. Set the set unit on the toilet owl. Align the mounting olts on the ottom of the set unit with the olt holes on the toilet owl. Next, ple the set unit on the toilet owl. Wter inlet (toilet owl) Mounting olt Bolt hole Chek tht the produt is firmly tthed to the toilet owl to prevent lekge from ourring from the wter inlet. Chek tht there is no deris on the toilet owl or set unit lensing wter inlet to prevent lekge from ourring from the lensing wter inlet. d e f g h 4. Temporrily tighten the set unit. (1) Ple the wsher nd spring wsher over the mounting olt nd hnd-tighten the nut. d Toilet owl e Spring wsher f Nut g Mounting olt h Plsti wsher Tighten the left nd right nuts lterntively in order to ensure even tightening to prevent wter lekge. 5. Tighten the set unit. Tighten the nut with the wrenh inluded in the pkge. 14
4 Conneting the Wter Supply Hose (To the set unit) Protetive p Protetive p Set unit wter supply inlet d Clip e Wter supply hose f Wter supply hose instlltion pking rket d Do not pply exessive fore when onneting the wter supply hose. e f (1) Remove the protetive p from the set unit wter supply inlet nd the wter supply hose. (2) Connet the wter supply hose to the set unit wter supply inlet. g O-ring g Be reful not to dmge the O-ring. * If the O-ring is dmged, lekge my our. Remove the p found on the shutoff vlve end of the wter supply hose immeditely prior to onneting the wter shutoff vlve. * During instlltion, deris my enter the wter supply hose, resulting in vlve mlfuntion. Connet the wter supply hose to the set unit while the hose is still in its pking rket. The metl fitting on the end of the wter supply hose hs restrited rottion, nd will not turn more thn 3 times. When onneting the wter supply hose, instll so tht it n rotte to oth the left nd right. 15
(3) Fsten with the lip. * The lip will only fsten if onneted s shown in the digrm. Clip Firmly set the lip on the produt from the side. * Do not tth t n ngle, s the lip nnot e ent in wy to properly seure the hose. Atth the lip firmly. * Inorret tthment will use wter lekge. (4) Remove the wter supply hose from its instlltion pking rket. Clik (5) Bend the lip to firmly seure the wter supply hose to the set unit wter supply inlet. After seuring, rotte the lip, nd hek tht it is tthed properly. Push the lip until it mkes n udile lik. * Inorret tthment will use wter lekge. When removing the lip, hold the lip with your fingers, insert flt-lde srewdriver, nd press down to remove s shown in the digrm. 16 ィス
5 Conneting the Wter Supply Hose (To the wter shutoff vlve) Wll wter supply d Clip Wter shutoff vlve O-ring d Wter supply hose Be reful not to dmge the power plug, or let it fll into the toilet owl. (1) Remove the p from the wter supply hose, nd onnet the hose to the wter supply of the wter shutoff vlve inlet. Be reful not to dmge the O-ring. * If the O-ring is dmged, lekge my our. Remove the p found on the wter shutoff vlve end of the wter supply hose immeditely prior to onneting the wter shutoff vlve. * During instlltion, deris my enter the wter supply hose, resulting in vlve mlfuntion. Ensure tht the wter supply hose is not kinked. * Othewise, the hose my e dmged, resulting in wter lekge. This my lso result in inomplete lening. 17
(2) Fsten with the lip. Atth the lip firmly. * Inorret tthment will use wter lekge. Clik (3) Seure the lip in the sme wy s with the set unit wter supply inlet. After seuring, rotte the lip, nd hek tht it is tthed properly. Push the lip until it mkes n udile lik. * Inorret tthment will use wter lekge. [Referene] When removing the lip, hold the lip with your fingers, insert flt-lde srewdriver, nd press down to remove s in the digrm. 6 Conneting to the Power Supply 1. Connet the power plug to the outlet. 2. Chek tht the power is on. Ensure tht the power LED on the produt is illuminted. 18 08M060_ ピーターパン取説 17_ ストレーナ取外し
7 Mounting the Remote Control Unit (1) Open the k over of the remote ontrol unit nd insert four 1.5-V AAA lkline tteries. Ple the tteries in the orret diretion, ligning the positive nd negtive terminls s indited inside the ttery omprtment. (2) Position the rket on the wll in the desired lotion for the remote ontrol unit (see Remote ontrol unit mounting lotion, pge 2). Mrk the positions of the mounting holes on the wll. Fsten the rket to the wll, y drilling holes nd using the fsteners pproprite for the wll mteril, s desried elow. Leve enough spe ove the top of the remote ontrol unit to llow the unit to e removed nd repled. If mounted in plywood pneling 3/16" (5 mm) or greter in thikness: Fsten the rket to the wll with the mounting srews. 52" (1320 mm) 31 1 /2" (800 mm) 44 7 /8" (1140 mm) 23 5 /8" (600 mm) 12" (300 mm) Referene for instlltion position Referene for esy opertion Unit: inh (mm) Instll the remote ontrol within n esily essile reh rnge for the user. The remote ontrol should e instlled where the user n esily operte it while seted on the toilet. Use the digrm t the left s guide for the lotion of the remote ontrol. In the event tht the toilet does not operte, hnge the position of the remote ontrol. * There is the possiility tht the toilet unit would not operte euse of n fluoresent light with inverter llst or for other environmentl resons within the room. * If the signl nnot e reeived, estlish the use of the ostrution nd remove it. Or, if it nnot e removed, hnge the instlltion position of the remote ontrol. * When instlling the remote ontrol on the right side (when fing the toilet), instll it within the rnge of referene for esy opertion s fr s possile. 4 3 /4" (120 mm) 9 1 /2" (240 mm) Mke sure to hek the opertion while sitting on the toilet set. Ple the remote ontrol temporrily in the position to e instlled nd press the STOP utton while tully sitting on the set. (Mke sure to perform the test opertion fter instlltion.) Then stnd in front of the toilet owl nd press the STOP utton. Chek tht there is eep (norml signl reeption sound) from the toilet unit. Do not press the uttons for front nd rer lensing. If pressed, wter will e spryed. Ensure there is enough spe to tth or deth the remote ontrol in the re immeditely ove the instlltion position. Ensure there is enough spe to tth or deth the remote ontrol in the re immeditely ove the instlltion position. 19
If mounted either in plywood pneling 3/16" (5 mm) or less in thikness or in drywll: 1 In plywood pneling, drill ø1/2" pilot hole, in dry wll, drill ø3/16" pilot hole. 2 Using hmmer, tp the plsti nhors into the holes. Plywood pneling : ø1/4" (6 mm) Drywll : ø3/16" (5 mm) Plsti Anhor d 3 Fsten the rket seurely to the nhors using mounting srews. As you tighten the srews, they re hrd to turn t first, then grdully get esier to turn, nd then re hrd to turn gin. Brket d Mounting Srew If mounted on tiled wll or in onrete: 1 1 /4". (33 mm) e f 1 Drill holes with dimeter of 1/4" (6 mm) nd depth of pproximtely 1-1/4" (33 mm). 2 Using hmmer, gently drive the plsti nhors into the holes. e Plsti Anhor f 1/4" (6 mm) g h 3 Fsten the rket seurely to the nhors using mounting srews. g Wll-mounted rket h Mounting Srew (3) Align the remote ontrol unit with the rket nd then push it down onto the rket. 20
8 Chek for Wter Lekge 1. Fully open the wter shutoff vlve nd let wter flow into the produt. 2. Chek for wter lekge. (1) Use the remote ontrol to flush the toilet severl times. (2) Chek tht there re no wter leks t the onnetion points. Wter lekge t the supply/drin wter onneting setions my not e oserved unless the toilet is flushed severl times. 3. Chek the flushing opertion. (1) Prepre 7 lls of toilet pper, nd put these in the toilet owl. For eh ll, use out 30" length of toilet pper. (2) Chek tht these re removed from the owl in single flush. If they re not removed with single flush, verify tht the wter pressure is t lest 14.5 psi (0.10 MP). 21
9 Atthing the Side Covers (1) Disonnet the power plug from the outlet. (2) Insert the "t" t the top of the side over into the "t reeiver" on the produt, nd push upwrds until it is fully inserted. T reeiver T Side over d e f (3) Push the ottom of the side over so tht the "lip" is fully inserted into the "lip support". (4) Seure the side over using the flt hed srew nd the oupling wsher, nd then tth the p. d Coupling wsher e Flt hed srew f Cp h g (5) Chek tht the side over is seurely mounted. (6) Connet the power plug to the outlet. g Clip support h Clip When the wter shutoff vlve is loted on the right when fing the toilet: (1) Remove the srew on the k of the right side over. (2) Remove the smll over pnel from the right side over. * Remove in the diretion indited. i (1) (3) Atth the smll over pnel to the left side over. (4) (3) (2) * Insert in the diretion indited. (4) Insert the srew on the k of the left side over to fsten the smll over pnel. i Smll over pnel 22
10 Test Opertion (Follow the steps elow to ondut test opertion when instlltion is ompleted.) 1. Chek rer lensing. (1) Use piee of toilet pper to over the set sensor. (2) Press [Clensing] on the remote ontrol. As the nozzle egins to spry, over the nozzle tip with your hnd to prevent wter from splshing. (3) Press [STOP] on the remote ontrol. The spry will stop. Set sensor If the remote ontrol is used under fluoresent light with inverter llst, the shower toilet my not operte. This depends on the lyout of the toilet. Plese turn off this lighting nd try gin. The produt is equipped with set sensor tht detets the user. In order for the spry fetures to operte, the user must e seted. When the toilet set is oupied, wter is emitted from round the nozzle s preliminry opertion. 2. Follow the sme proedure to hek the front lensing feture. Do not hnge settings of the omfort fetures. Leve the settings for the ustomer. The omfort fetures of the shower toilet should e set ording to the ustomer s preferene. So ontrtors re requested not to set these. If some re set, the ontrtor should explin the detils of them nd the feture to the ustomer. This is espeilly so with the power sve funtion s the toilet set my feel old if the ustomer does not know of this. The omfort fetures These re the funtions provided for the ustomers omfort. The mjor omfort fetures inlude the following: Toilet set nd wter temperture ontrol Deodorizer Power sve Wrm ir temperture seletion when drying strts Set heter uto OFF * Mke sure to return the settings to the defult position fter the test opertion. (Press the BIDET nd POWER SAVE ON/OFF uttons simultneously for two seonds.) * Some funtions my not e provided depending on model. Chek list Chek for wter lekge Between the wter shutoff vlve nd the floor or wll Between the wter shutoff vlve nd the wter supply line Between the wter shutoff vlve nd the wter supply hose Between the set unit nd the toilet owl Between the toilet owl nd the floor Chek remote ontrol opertion Is the wter shutoff vlve fully open? Cheked 23
11. If the wter does not flow well, len the filter. (1) Close the wter shutoff vlve to stop the wter. Plese do not remove the filter when the wter supply vlve is open. * Wter will lek from the filter. (2) Press [FULL], or press the flush utton on the produt * Wit pproximtely 20 seonds. (3) Disonnet the power plug from the outlet. Filter (4) Remove the left side over s seen from the front, ple loth or something similr on the floor elow, nd remove the filter. (5) Wsh wy ny deris inside the filter, nd from the O-ring. O-ring (6) Fully tighten the filter. When instlling the filter inside the wter shutoff vlve, mke sure tht the wter shutoff vlve is tightened ompletely. * If this is not tightened ompletely, then there my e lekge from the filter. (7) Instll the side over. Side over (8) Connet the power plug to the outlet. (9) Open the wter shutoff vlve. * If the wter ontinues to not flow well, hek the wter supply pressure. 24
12. To prevent wter from freezing inside this produt, follow the proedure elow to drin the wter. (1) Close the wter shutoff vlve to stop the wter. Plese do not remove the filter when the wter supply vlve is open. * Wter will lek from the filter. (2) Press [FULL], or press the flush utton on the produt * Wit pproximtely 20 seonds. Flush utton (3) Remove the left side over (seen from the front), ple loth or something similr on the floor elow, remove the filter, nd drin the wter. (4) Remove ll remining wter from the produt. <To drin wter from the produt> On the remote ontrol, press nd hold down [NOZZLE CLEANING] nd [MASSAGE] simultneously for 2 seonds. * Wter will drin from the produt for pproximtely 15 seonds. (5) Wsh wy ny deris inside the filter nd from the O-ring. (6) Fully tighten the filter. (7) Instll the side over. (8) Chek for lekge from the wter shutoff vlve, nd disonnet the power plug from the outlet. 25
ENGLISH In the United Sttes: DXV y Amerin Stndrd One Centennil Avenue Pistwy, New Jersey 08855 Attention: Diretor of Customer Cre For residents of the United Sttes, wrrnty informtion my lso e otined y lling the following toll free numer: (800) 227-2734 www.dxv.om In Cnd: DXV y Amerin Stndrd 5900 Aveury Rod Mississug, Ontrio L5R 3M3 Cnd Toll Free: 1-800-387-0369 Lol: 905-306-1093 Fx: 1-800-395-1498 www.dxv. In Mexio: DXV y Amerin Stndrd Vi Morelos 330 Col. Snt Clr Cotitl Etepe, Estdo de Méxio 55540 Toll Free: 01-800-8391200 www.dxv.mx 2014 AS Ameri In. PCW-1312-US-ASB(14030)