J/88, J/Boats, 8.90 m (29.19') J/Boats photos HEADSAIL HANDLING SYSTEMS

J/88, J/Boats, 8.90 m (29.19') J/Boats photos HEADSAIL HANDLING SYSTEMS

Carbo Racing Foil The engineering resins in these strong, lightweight head foils offer significant advancements over the weaker PVC materials used by other manufacturers. The low-friction twin headsail grooves are ultra-smooth, allowing hoists, douses, and headsail changes to be easily and efficiently executed. Impact resistance is unmatched, with far less foil damage from loaded spinnaker poles, especially in cold weather. Heat has little effect on stiffness. Foils are UV protected and easy for the trimmer to see. For mast-up installation, simply uncoil the foil and snap onto the stay. Aluminum Chafe Guard An aluminum chafe guard keeps spinnaker sheets from damaging the foil during high-speed jibes. Testing shows this guard weighs the same as aramid fiber or composite, and is impervious to wear, unlike UHMW plastic tape which wears away quickly. A Harken chafe guard is included free with the purchase of a 7000, 7001, or 7002 kit. Trim cap Feeder for smooth hoists: Funnel-shaped stainless feeder smoothly guides boltrope into head foil for fast hoists. Prefeeder: Hardcoat-anodized, PTFE-coated aluminum rollers spin freely on low-friction bushings. Kit includes prefeeder. Actual size Unit 3 7006 7000 7001 7002 7003 Unit 2 Unit 1 Unit 0 7000.30 7001.30 7002.30 Jeanneau Sun Fast 3600, 11.25 m (36'10") Jeanneau photo Max wire Max rod Extrusion Max headstay Spacer tube Extrusion Full system Luff tape Part Ø Ø length length length weight weight* size** No. Description in mm dash mm ft/in m ft/in m ft/in m lb/ft kg/m lb kg in mm 7000.9m Unit 0 1 /4 6-10 6.35 29'6" 9 33'6" 10.2 3'3" 1.102.152 3.29 1.50 #5 ( 5 /32) 4 7000.12m Unit 0 1 /4 6-10 6.35 39'4" 12 43'4" 13.2 3'3" 1.102.152 4.29 1.95 #5 ( 5 /32) 4 7000.15m Unit 0 1 /4 6-10 6.35 49'2" 15 53'2" 16.2 3'3" 1.102.152 5.30 2.41 #5 ( 5 /32) 4 7001.12m Unit 1 5 /16 8-17 8.38 39'4" 12 43'4" 13.2 3'3" 1.162.241 6.99 3.18 #6 ( 6 /32) 5 7001.16m Unit 1 5 /16 8-17 8.38 52'6" 16 56'5" 17.2 3'3" 1.162.241 9.13 4.14 #6 ( 6 /32) 5 7001.20m Unit 1 5 /16 8-17 8.38 65'7" 20 69'6" 21.2 3'3" 1.162.241 11.25 5.10 #6 ( 6 /32) 5 7002.16m Unit 2 3 /8 10-25 10.31 52'6" 16 56'6" 17.2 3'3" 1.185.275 10.43 4.73 #6 ( 6 /32) 5 7002.20m Unit 2 3 /8 10-25 10.31 65'7" 20 69'7" 21.2 3'3" 1.185.275 12.90 5.83 #6 ( 6 /32) 5 7002.24m Unit 2 3 /8 10-25 10.31 78'9" 24 82'9" 25.2 3'3" 1.185.275 15.29 6.93 #6 ( 6 /32) 5 7003.24m Unit 3 7 /16 11-30 11.1 78'8.5" 24 82'9" 25.2 3'3" 1.245.365 20.08 9.10 #6 ( 6 /32)/#7 ( 7 /32) 5/6 7003.28m Unit 3 7 /16 11-30 11.1 91'10" 28 95'9" 29.2 3'3" 1.245.365 23.31 10.57 #6 ( 6 /32)/#7 ( 7 /32) 5/6 7006 Replacement prefeeder 3 oz 85 g 7000.30 Unit 0 chafe guard 3'3" 1 2.5 oz 70 g 7001.30 Unit 1 chafe guard 3'3" 1 2.9 oz 82 g 7002.30 Unit 2 chafe guard 3'3" 1 3 oz 85 g *Weight without chafe guard. **Nominal dimensions only, actual luff tape dimensions are larger. 166

Small Boat Furling Small Boat Furlers Harken Small Boat furling systems allow the trailerable cruising or dinghy sailor to set and furl the jib from the cockpit. Drums and halyard swivels feature multiple stacked races of Delrin or Torlon bearings for smooth rotation under load. Small Boat units are for furling only, not reefing. Upper swivel Hoistable swivel Halyard Hoistable Halyard Swivels An optional hoistable ball bearing halyard swivel can be installed on the headstay so the sail can be raised or lowered without removing the headstay. Swivels are independent of the headstay, which allows the luff to be tensioned separately from the mast rake. Hoistable swivels work along with your standard Harken Small Boat furler. Unfurl Furl The high-load Small Boat furler with hoistable halyard is available as a kit. Use for: 434 Dinghies under 4.9 m (16 ft) 435 Dinghies to 6.1 m (20 ft) Catamarans to 5.5 m (18 ft) 436 Cruising boats to 7.6 m (25 ft) Catamarans to 7 m (23 ft) Delrin is a registered trademark of E. I. du Pont de Nemours and Company or its affiliates. Torlon is a registered trademark of Solvay Advanced Polymers. FURLER KIT 483 464 465 482 HOISTABLE SWIVELS SMALL BOAT FURLERS 435 (164, 165) 434 (162, 163) 436 (207, 208) Furlers Components (if ordering separately) Upper Hoistable Weight swivel swivel Drum Upper swivel Hoistable swivel Drum Fits Part No. Part No. Part No. oz g oz g oz g furler 162 163 2.6 74 5 142 434 164 464 165 2.6 74 2.9 82 5 142 435 207 465 208 9.2 261 8.9 252 13.6 386 436 Pin-to-pin Drum Line Jaw Max luff Clevis pin Maximum Part length Ø Ø width wire Ø Ø Weight working load No. Description in mm in mm in mm in mm in mm in mm oz g lb kg 434 Furler 2 1 /2 64 2 7 /8 73 5 /32 4 5 /16 8 1 /8 3 1 /4 6 7.6 215 500 227 435 High-load furler 2 1 /2 64 2 7 /8 73 5 /32 4 5 /16 8 1 /8 3 1 /4 6 7.6 215 950 431 436 Cruising furler 4 102 4 3 /16 106 1 /4 6 3 /8 10 3 /16 5 5 /16 8 22.8 646 2000 907 464 Halyard swivel/hole for 4 mm wire 4 3 /16* 124* 5 /32 4 5 /32 4 2.9 82 810 367 465 Halyard swivel/hole for 5 mm wire 5 11 /16* 144* 3 /16 5 3 /16 5 8.9 252 1190 540 482 Halyard swivel/hole for 6 mm wire 7 19 /32* 193 7 /32 6 7 /32 6 16.8 477 3000 1361 483 Furler kit/hoistable halyard*** 2 1 /2** 64** 2 7 /8 73 5 /32 4 5 /16 8 5 /32 4 1 /4 6 11.2 318 950 431 *Shackle to shackle. **Tang hole to tang hole. ***Includes drum, upper swivel, and hoistable swivel. Includes drum and upper swivel. 167

Small Boat Underdeck Furling Underdeck Furlers Small Boat underdeck furling units are ideal for sportboats and daysailers from 4.8 m to 9 m (16 to 30 ft). The drum is located beneath the deck, lowering the tack height for maximized sail area. The single through-deck ball joint provides a low-profile, nearly watertight system that aligns the spool to the headstay. Like all Small Boat furlers, the underdeck furler is for furling only, not reefing. Hoistable Swivels An optional hoistable ball bearing halyard swivel can be installed on your headstay so you can raise or lower the sail without removing the headstay. Swivels are independent of the headstay, allowing you to tension the luff separately from the mast rake. Hoistable swivels work along with your standard Harken Small Boat furler. Tack Adapter Tangs Stainless steel tack adapter tangs are used to adapt clevis pin diameters on headstays to the standard clevis pin size that comes on the Harken unit. A third hole accepts lashing to adjust jib luff tension. 464 465 482 HOISTABLE SWIVELS 479 480 481 489 TACK ADAPTER TANGS Spherical joint Deck Stationary Belowdeck bracket Spool pivots to align with load. Turnbuckle eye on stationary bracket attaches to an underdeck chainplate. 478 UNDERDECK FURLERS 477 493 Fairlead feeds line onto the spool. Tang Upper pin Ø Lower pin Ø Fits adapter in mm in mm furler 479 5 /16 8 7 /16 11 478 480 3 /8 10 7 /16 11 478 481 7 /16 11 7 /16 11 478 489 5 /16 8 5 /16 8 493 Components (if ordering separately) Upper Hoistable Weight swivel swivel Drum Upper swivel Hoistable swivel Drum Fits Part No. Part No. Part No. oz g oz g oz g furler 164 464 HC9226 2.6 74 2.9 82 24 680 477 207 465 HC10893 9.2 261 8.9 252 42.6 1201 493 HCP141 482 HC9976 15 431 16.8 477 81 2296 478 Pin-to-pin Drum Line Jaw Max luff Clevis pin Maximum Part length Ø Ø width wire Ø Ø Weight working load No. Description in mm in mm in mm in mm in mm in mm oz g lb kg 477 Underdeck furler/small* 6 1 /8 156 3 1 /8 79 1 /8-5 /32 3-4 5 /16 8 1 /8 3 1 /4 6 23.3 661 950 431 493 Underdeck furler/medium* 7 3 /8 188 4 102 5 /32-3 /16 4-5 3 /8 10 3 /16 5 5 /16 8 50.5 1433 2000 907 478 Underdeck furler/large* 10 7 /32 260 5 127 3 /16-1 /4 5-6 1 /2 12 7 /32 6 7 /16 11 96 2721 3000 1361 479 4 mm tack adapter tang 1 1 /2** 38** 5 /32 4 5 /16 8 5.2 147 3000 1361 480 5 mm tack adapter tang 1 1 /2** 38** - 3 /16 5 3 /8 10 5.2 147 3000 1361 481 6 mm tack adapter tang 1 1 /2** 38** 7 /32 6 7 /16 11 5.2 147 3000 1361 489 8 mm tack adapter tang 1 3 /8** 35** 5 /32 4 5 /16 8 3.2 91 2000 907 *Includes drum and upper swivel. Does not include hoistable swivel. **Tang hole to tang hole. 168

Spinnaker Staysail & Gennaker Furling Spinnaker Staysail Furled staysails are easy to hoist rolled and can be deployed or doused from the cockpit. In marginal conditions the sail can be struck instantly without changing the trim of the boat. Multiple stacked races of Torlon ball bearings ensure smooth operation under load. Systems include a lower drum with snap shackle, fairlead and Cam-Matic cleats, and an upper swivel with provision for halyard attachment. Gennaker Furling Gennaker furling was developed for large singlehanded boats and huge oceangoing multihulls. The drum unit features a fairlead, while the upper swivel is designed for direct halyard attachment. Custom designs are available for larger boats. Screecher Furling Use screecher furling systems on multihulls up to 9.60 m (32 ft) and easily driven sport boats. Perfect for jib reaching, screechers are set on the bowsprit. They are often carried upwind in light to moderate conditions and used as storm spinnakers when it s blowing. Systems are sized to handle loads of 2:1 halyards. Multiple stacked races of Torlon ball bearings ensure smooth rotation under load. Fairleads allow the furling line to lead aft to the cockpit. Multiple stacked races of Torlon ball bearings roll easily under load. Torlon is a registered trademark of Solvay Advanced Polymers. The LP is a perpendicular line measured from the luff to clew. 1851 1852 3029 3049 Corsair F31 Ø Length Max line Max Max Part Drum Swivel Drum Swivel Ø* halyard load Weight luff length Max LP No. Description in mm in mm in mm in mm in mm lb kg oz g ft m ft m 1851 Small staysail furler 2 7 /8 73 1 25 5 3 /16 132 4 3 /16 106 5 /32 4 950 431 13 366 50 15.25 13.5 4.1 1852 Large staysail furler 4 1 /4 108 1 7 /16 37 7 5 /16 186 5 7 /8 149 1 /4 6 2000 907 28 800 70 21.33 20 6 3029 Small gennaker/screecher furler 2 7 /8 73 1 25 3 1 /4 83 4 1 /8 105 5 /32 4 950 431 9 255 30 9.14 13.5 4.1 3049 Large gennaker/screecher furler 4 1 /4 108 1 7 /16 37 5 127 5 7 /8 149 1 /4 6 2000 907 24.5 695 40 12.19 20 6 *Smaller line may be required for spinnaker staysails with long foot lengths. 169

Ordering Furling 1. Choose furler type The table below is based on sailing style and approximate boat size. This table is only a guideline. Do not use it to determine unit size. Size is based on the headstay and clevis pin diameters listed on unit pages. Comparison Chart MKIV Racers/performance cruisers ESP Cruisers Note: Typical boat lengths are listed as a guideline but are not the determining factor. Check with Harken if your length varies. Typical boat lengths Unit 0: 6.5 9.1 m (22 30 ft) Unit 1: 8.5 11 m (28 36 ft) Unit 2: 10 14.2 m (35 46 ft) Unit 3: 13.7 18.3 m (45 60 ft) Unit 4: 19.8 24.4 m (65 80 ft) Unit 0: 6 8.5 m (20 28 ft) Unit 1: 8 10.7 m (26 35 ft) Unit 2: 10.4 14 m (34 46 ft) Unit 3: 13.7 18.6 m (45 61 ft) Foils Halyard and tack swivel Drum Line Double-groove Air foil Stainless steel feeder Independent swivels for improved sail shape Removable split drum for racing Included on Units 0, 1, 2 Single-groove round foil Stainless steel feeder Fixed Fixed Not included 2. Determine unit size Size is based on the headstay and clevis pin diameters listed on unit pages. Choose between unit sizes when diameters are shared by considering stay length and typical boat size recommendations. Contact Harken if you have any questions. 3. Determine if additional foils needed Use the I and J measurements to determine the length of the headstay. If the existing headstay is longer than the standard length listed under Headstay Length on unit pages, order additional foils and connectors. In some cases one or two extra foils and connectors may be necessary. 4. Determine toggle, link plate, or leg kit Use short toggle (MKIV) or short leg kits (ESP) for maximum luff length. For ESP, use long or medium leg kits to accommodate a turnbuckle or to clear an anchor. 5. Choose lead block kit and accessories, ESP - order line Harken recommends equipping every furling system with a ratchet lead block kit. Other parts on the Furling Accessories page (188-189) include equipment for halyard management and racing hardware for faster sail changes. Order line for ESP furlers. 6. Prepare sail and headstay Have a luff tape added to your genoa. Match the sail length to the stay length minus the height of the halyard swivel and lower unit. See sizing information on page 171. All MKIV and those ESP furlers with long or medium leg kits install over the existing turnbuckle. The turnbuckle is accessible for adjustment by raising the drum. See the MKIV & ESP Toggle & Rigging Options on page 182 to determine toggle and rigging requirements. Some headstays will require cutting and shortening to fit Harken toggle. Sometimes only the lower threaded turnbuckle fitting needs changing. Check with a professional rigger on stay condition before reusing stay. For all units, rod rigging requires a Harken rod adapter stud. It must be cut and coldheaded by an authorized rod service center. 7. Contact If you have questions, please contact your dealer or Harken Technical Service. Measure clevis pin diameter MKIV Jaw/jaw toggle Bow I Forestay Measure wire or rod diameter J Headstay length = I 2 + J 2 ESP short leg kit 170 MKIV long link plate ESP long leg kit

Furling Dimensions MKIV Using Toggle* F G H I Unit A B C D E Max Min Max Min Max Min Max Min 0 3 3 /4" 5 7 /8" 1 7 /8" 5 1 /2" 2 5 /8" 41" 39 1 /4" 8 3 /8" 8" 7 5 /16" 7" 2 5 /16" 2" 96 mm 150 mm 47 mm 140 mm 66 mm 1041 mm 997 mm 213 mm 203 mm 186 mm 175 mm 59 mm 51 mm 1 4 3 /4" 7" 2" 6 5 /8" 3 1 /16" 46 1 /4" 42 1 /4" 12" 9 3 /4" 11" 8 3 /4" 5" 2 7 /8" 120 mm 178 mm 51 mm 167 mm 78 mm 1175 mm 1073 mm 305 mm 247 mm 280 mm 222 mm 129 mm 71 mm 2 5 5 /8" 9 1 /8" 2 9 /16" 8 3 /16" 3 13 /16" 51 3 /4" 46 3 /4" 15 1 /8" 12 1 /16" 13 15 /16" 10 7 /8" 6 7 /16" 3 3 /8" 143 mm 231 mm 66 mm 208 mm 97 mm 1314 mm 1187 mm 384 mm 306 mm 348 mm 276 mm 164 mm 85 mm 3 7 5 /16" 11 5 /8" 3 3 /8" 9 3 /4" 4 3 /4" 50 5 /8" 18 7 /16" 16 5 /8" 7 3 /8" 186 mm 296 mm 86 mm 247 mm 121 mm 1286 mm 467 mm 420 mm 188 mm 4 8 15 /16" 11 1 /16" 5 1 /8" 55 5 /16" ** ** 227 mm 280 mm 130 mm 1405 mm *See MKIV long link plate dimensions below. ** Soft-attachment tack, head, and halyard; distance varies. Max refers to using stud jaw toggle. Use Min when adding long link plate dimensions. ESP Using Short Leg Kit* ** ** 20" 509 mm 8 5 /8" 220 mm F Unit A B C D E Max Min G H I 0 1 7 /8'' 4 9 /16'' 1 3 /8'' 6 1 /2'' 2 5 /8'' 37 7 /8'' 22 1 /2'' 8 5 /16'' 7 7 /16'' 3'' 48 mm 116 mm 36 mm 166 mm 66 mm 962 mm 572 mm 211 mm 190 mm 76 mm 1 2 3 /4'' 5 1 /8'' 1 3 /8'' 8'' 3'' 38 9 /16'' 23 7 /16'' 9 7 /8'' 9 1 /16'' 3 11 /16'' 70 mm 131 mm 34 mm 200 mm 78 mm 980 mm 595 mm 251 mm 230 mm 93 mm 2 3 7 /8'' 7 5 /16'' 2'' 9 7 /8 3 5 /8'' 40 3 /4'' 25'' 12 15 /16'' 11 13 /16'' 4 15 /16'' 99 mm 185 mm 51 mm 250 mm 97 mm 1034 mm 635 mm 329 mm 300 mm 125 mm 3 5 1 /8'' 9 7 /16'' 2 1 /8'' 11 3 /4'' 4 3 /4'' 42 15 /16'' 27'' 16 1 /16'' 14 5 /8'' 6 1 /2'' 130 mm 240 mm 53 mm 298 mm 121 mm 1091 mm 686 mm 408 mm 370 mm 165 mm *See ESP medium and long leg kit dimensions below. E Max and Min are dependent on foil position at adjuster tube. ESP Medium and Long Leg Kit *Note: If medium or long leg kit is used, add the following dimensions to F, G, H, and I. ESP leg kit Medium leg kit add Long leg kit add Unit 0 5" 130 mm Unit 1 3 3 /4" 95 mm 8 3 /4" 220 mm Unit 2 7" 176 mm 11 3 /4" 300 mm Unit 3 8 1 /2" 215 mm 14 1 /2" 370 mm D E C H Feeder entrance Adjuster tube Tack shackle F Halyard shackle A Head shackle B MKIV Long Link Plate *Note: If a long link plate is used, add the following dimensions to F, G, H, and I (based on whether plate is used full-length or shortened to one of five hole positions). 1 /2" (12.7 mm) clevis pin Add 13 Unit 1 1 /4" 6 5 /8" (337 168 mm) 5 /8" (15.9 mm) clevis pin Add 11 1 /4" 4 3 /8" (286 111 mm) 5 /8" (15.9 mm) clevis pin Add 16 Unit 2 1 /8" 8 1 /4" (410 210 mm) 3 /4" (19.1 mm) clevis pin Add 13 9 /16" 5 11 /16" (344 144 mm) ESP Lower Unit with Short Leg Kit I H G C Feeder entrance Unit 3 3 /4" (19.1 mm) clevis pin Add 19 9 /16" 10 11 /16" (497 271 mm) 7 /8" (22.2 mm) clevis pin Add 19 7 /8" 11" (505 279 mm) Foil Dimensions J K Foil length System Unit in mm in mm ft m Luff tape* 0 7 /8 23 1 1 /32 26 7 2.13 #6 6 /32" (5 mm) 1 1 25 1 1 /8 29 7 2.13 #6 6 /32" (5 mm) 2 1 1 /4 32 1 3 /8 36 7 2.13 #6 6 /32" (5 mm) 3 1 1 /2 38 1 11 /16 43 7 2.13 #6 6 /32" (5 mm) 4 1 3 /4 44 1 27 /32 47 7 2.13 #6 6 /32" (5 mm) 0 1 1 /4 31 6 9 /16 2 #6 6 /32" (5 mm) 1 1 9 /16 40 6 9 /16 2 #6 6 /32" (5 mm) 2 2 1 /8 53.5 6 9 /16 2 #6 6 /32" (5 mm) 3 2 3 /4 69 6 9 /16 2 #6 6 /32" (5 mm) *Nominal dimensions only, actual luff tape dimensions are larger. MKIV ESP J MKIV J ESP K Clevis pin D E MKIV Tack shackle Pivot point I H G F 171

MKIV Jib Reefing & Furling 1 FOR RACING AND PERFORMANCE CRUISING SAILORS MKIV furling systems are strong, lightweight and aerodynamic, with the performance and features Harken is known for. Longevity, ease of use, and simplicity of installation are crucial components of the design. These free-rolling furlers make all the difference in headsail control by allowing racers and cruisers to quickly furl and reef from the safety of the cockpit, while maintaining great sail shape and optimal speed. 2 3 172 DETAILS MAKE THE DIFFERENCE EASY REEFING AND FURLING Multiple rows of large-diameter Torlon ball bearings used in high-load areas to minimize friction for easy reefing and furling; require no lubrication or isolating seals. MORE FURLING POWER Large inner spool diameter increases mechanical advantage for powerful reefing and furling. Smaller outside dimension allows unit to fit narrow bows or belowdeck. Unit rotates around rod or wire headstay so furling bearings do not carry the headstay load for easy furling. LONG-LASTING PROTECTIVE FINISH Aluminum line guard, torque tube, and swivels are deepsaturation hardcoat-anodized for no-fade UV-stabilization, strength, and durability. The hardcoat-anodized line guard is urethane-coated for additional corrosion protection. Specially formulated low-stretch black line is abrasionand UV-resistant; standard on units 0, 1, and 2. Torlon is a registered trademark of Solvay Advanced Polymers. Sta-Lok is a registered trademark of Sta-Lok Terminals, Ltd. DO NOT use Harken equipment for human suspension. 1. Halyard Swivel Turns Freely Strong, lightweight halyard swivel reduces windage and weight aloft to minimize pitching and heeling. Stacked bearing races evenly distribute radial and thrust loads to ball bearings; foils turn freely under halyard loads. Independent halyard and tack swivels furl sail center before head and tack for improved sail shape and upwind pointing. 2. Strong Foil Joints Tough triple-interlock foil joints withstand years of torque loading. Connector s geometric shape interlocks to foil and secures with a syringe-injected adhesive into an engineered channel. Screws provide final lock. 3. Easy-to-Assemble Foils C-shaped open connectors with low-friction plastic isolators slip onto the headstay wire and into foil for easy installation. 4. Drum Installs Over Existing Turnbuckle Units are adaptable to a variety of rigging options for easy installation. Harken toggle assembly accepts standard turnbuckle using swage, rod, Norseman, or Sta-Lok terminals. Toggle flips for fork or tang chainplate installation. A single stainless steel clevis pin provides access to the turnbuckle for adjustment. 5. Stainless Steel Feeder Stainless steel feeder allows fast singlehanded hoist and quick sail changes. 6. Removable Split Drum Line guard and spool come off easily for racing. 7. Double Foil Grooves for Racing Aerodynamic aluminum Air foils handle extreme reefing loads. Double foil grooves allow fast hoists, douses, and sail changes. 4 5 6 7

MKIV Unit 0 Typical Boat Length 22' - 30' (6.5-9.1 m) 5 /32", 3 /16", 7 /32" (4, 5, 6 mm) -4, -6 (4.37, 5.03 mm) 5 /16", 3 /8", 7 /16" (7.9, 9.5, 11.1 mm) Headstay Length Standard 38'7" (11.77 m); max 45'7" (13.9 m) 7410.10 Furling system 7410.20 5/16 Eye/jaw reversible toggle assembly with 5 /16" (7.9 mm) clevis pin 7410.20 3/8 Eye/jaw reversible toggle assembly with 3 /8" (9.5 mm) clevis pin 7410.20 7/16 Eye/jaw reversible toggle assembly with 7 /16" (11.1 mm) clevis pin 7410.30 Extra 7' (2.13 m) luff foil extrusion 7410.31 Extra 6 1 /2" (165 mm) connector with bushings 7420-4 -4 Rod adaptor stud (thread Ø UNF 7 /16")* 7421-6 -6 Rod adaptor stud (thread Ø UNF 7 /16")* *Use with conventional turnbuckle. 7410.30 7411.30 7410.31 7411.31 7420-4 7421-6 7422-8 7423-10 7424-12 MKIV Unit 1 Typical Boat Length 28' - 36' (8.3-11 m) 1 /4", 9 /32", 5 /16" (6, 7, 8 mm) -8, -10, -12 (5.72, 6.35, 7.14 mm) 1 /2", 5 /8" (12.7, 15.9 mm) Headstay Length Standard 45'11" (13.99 m); max 52'11" (16.12 m) 7411.10 Furling system 7411.20 1/2 Eye/jaw reversible toggle assembly with 1 /2" (12.7 mm) clevis pin 7311.20 1/2 Jaw/jaw toggle assembly with 1 /2" (12.7 mm) clevis pin 7311.20 5/8 Stud/jaw toggle assembly with 5 /8" (15.9 mm) clevis pin (thread Ø UNF 5 /8" LH) 7311.21 1/2 Long link plate with toggle assembly with 1 /2" (12.7 mm) clevis pin 7311.21 5/8 Long link plate with toggle assembly with 5 /8" (15.9 mm) clevis pin 7411.30 Extra 7' (2.13 m) luff foil extrusion 7411.31 Extra 7" (178 mm) connector with bushings 7422-8 -8 rod adaptor stud (thread Ø UNF 1 /2")* 7423-10 -10 rod adaptor stud (thread Ø UNF 1 /2")* 7424-12 -12 rod adaptor stud (thread Ø UNF 5 /8")* *Use with conventional turnbuckle. 7311.20 1/2 7410.20 5/16 7410.20 3/8 7410.20 7/16 7411.20 1/2 7311.20 5/8 Tartan 4700, 46.875', Tim Jackett, Tartan Yachts 7311.21 1/2 7311.21 5/8 173

MKIV Unit 2 Typical Boat Length 10.6-14.2 m (35' - 46') 8, 10 mm ( 5 /16", 3 /8") -12, -17, -22 (7.14, 8.38, 9.53 mm) 15.9, 19.1 mm ( 5 /8", 3 /4") Headstay Length Standard 18.38 m (60'4"); max 20.51 m (67'4" ) 7412.10 Furling system 7412.20 5/8 Eye/jaw reversible toggle assembly with 15.9 mm ( 5 /8") clevis pin 7312.20 5/8 Jaw/jaw toggle assembly with 15.9 mm ( 5 /8") clevis pin 7312.20 3/4 Stud/jaw toggle assembly with 19.1 mm ( 3 /4") clevis pin (thread Ø UNF 3 /4" LH) 7312.21 5/8 Long link plate with toggle with 15.9 mm ( 5 /8") clevis pin 7312.21 3/4 Long link plate with toggle with 19.1 mm ( 3 /4") clevis pin 7412.30 Extra 2.13 m (7') luff foil extrusion 7412.31 Extra 229 mm (9") connector with bushings 7424-12 -12 rod adaptor stud (thread Ø UNF 5 /8")* 7425-17 -17 rod adaptor stud (thread Ø UNF 5 /8")* 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4")* *Use with conventional turnbuckle. 7412.30 7413.30 7414.30 7412.31 7413.31 7414.31 7424-12 7425-17 7426-22 7427-30 7428-40 7429-48 7412.20 5/8 MKIV Unit 3 Typical Boat Length 13.7-18.3 m (45' - 60') 11, 12 mm ( 7 /16", 1 /2") -22, -30 (9.53, 11.10 mm) 19.1, 22.2 mm ( 3 /4", 7 /8") Headstay Length Standard 22.76 m (74'8"); max 24.89 m (81'8") 7413.10 Furling system* 7413.20 3/4 Jaw/jaw with short link plate with 19.1 mm ( 3 /4") clevis pin 7413.20 7/8 Jaw/jaw with short link plate with 22.2 mm ( 7 /8") clevis pin 7313.21 3/4 Long link plate with toggle with 19.1 mm ( 3 /4") clevis pin 7313.21 7/8 Long link plate with toggle with 22.2 mm ( 7 /8") clevis pin 7413.30 Extra 2.13 m (7') luff foil extrusion 7413.31 Extra 248 mm (9 3 /4") connector with bushings 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4")** 7427-30 -30 rod adaptor stud (thread Ø UNF 7 /8")** *Line not included. **Use with conventional turnbuckle. 7312.20 5/8 7413.20 3/4 7413.20 7/8 7414.20 7/8 7414.20 1 7414.20 1 1/8 7312.20 3/4 MKIV Unit 4 Typical Boat Length 19.8-24.4 m (65' - 80') 12, 14, 16 mm ( 1 /2", 9 /16", 5 /8")* -30, -40, -48 (11.10, 12.7, 14.3 mm) 22.2, 25.4, 28.57 mm ( 7 /8", 1", 1 1 /8") Headstay Length Standard 22.88 m (75'1"); max 27.15 m (89'1") 7414.10 Furling system** 7414.20 7/8 Jaw/jaw with short link plate with 22.2 mm ( 7 /8") clevis pin 7414.20 1 Jaw/jaw with short link plate with 25.4 mm (1") clevis pin 7414.20 1 1/8 Jaw/jaw with short link plate with 28.57 mm (1 1 /8") clevis pin 7414.30 Extra 2.13 m (7') luff foil extrusion 7414.31 Extra 270 mm (10 3 /4") connector 7427-30 -30 rod adaptor stud*** 7428-40 -40 rod adaptor stud*** 7429-48 -48 rod adaptor stud*** *For 19 mm (3/4") wire Ø contact Harken. **Line not included. ***Use with conventional turnbuckle. 174 7312.21 5/8 7312.21 3/4 7313.21 3/4 7313.21 7/8

MKIV Underdeck Jib Reefing & Furling FOR PERFORMANCE RACING AND CRUISING SAILORS Harken s MKIV Underdeck furling is the perfect solution for performance racers and cruisers who want an aerodynamic system with a minimal amount of equipment above deck. The drum is located beneath the deck, lowering the tack height for maximized sail area. 1 Unit 0 2 Unit 1 and larger DETAILS MAKE THE DIFFERENCE EASY REEFING AND FURLING Ball bearings between the center hub and deck bearing provide low-friction furling. DURABLE MATERIALS AND CONSTRUCTION Size 1 and larger: Aluminum line guard, torque tube, and swivels are deep-saturation hardcoat-anodized for no-fade UV-stabilization and durability. The hardcoatanodized line guard is urethane-coated for additional corrosion protection. The threaded height adjuster uses dissimilar metals (stainless steel and bronze) to prevent galling. Size 0: A one-piece integrated deck bearing and line guard provides durability and corrosion resistance. EASY TO MAINTAIN The furler can be flushed clean with detergent water like traditional furling. The through-deck bearing minimizes water seepage into the underdeck compartment. 1. Torque Tube Houses Full-Length Turnbuckle The torque tube houses a full-length turnbuckle for optimal mast rake and tension adjustment. 2. Articulating Torque Tube Attachment A torque tube universal joint on Units 1, 2, and 3 provides a high-strength universal connection to allow ample headstay sag when sailing downwind. The Unit 0 features an articulating ball joint, eliminating the universal joint and toggle to reduce weight and to simplify maintenance. 3. Belowdeck Drum Fits Narrow Bows The small outside drum diameter lets unit fit inside narrow bows. 4. Installation Options Units 1 and larger have self-locking threaded height adjusters for a correct fit between the chainplate and deck. The Unit 0 does not need a height adjuster. The furler and headstay are independent of each other, allowing flexible installation options. Unit 0 3 4 Unit 1 and larger Unit 1 and larger Unit 0 DO NOT use Harken equipment for human suspension. 175

MKIV Underdeck Unit 0 Typical Boat Length 22' - 30' (6.7-9.1 m) 3 /16", 7 /32" (5, 6 mm) -4, -6 (4.37, 5.03 mm) Headstay Length Standard 38'4" (11.7 m); max 45'4" (13.8 m) 7410.11 Furling system 7410.30 Extra 7' (2.13 m) luff foil extrusion 7410.31 Extra 7" (178 mm) connector with bushings MKIV Underdeck Unit 1 Typical Boat Length 28' - 36' (8.3-11 m) 1 /4", 9 /32", 5 /16" (6, 7, 8 mm) -8, -10 (5.72, 6.35 mm) 1 /2" (12.7 mm) Headstay Length Standard 45'11" (13.99 m); max 52'11" (16.12 m) 7411.11 1/2 Furling system with 1 /2" (12.7 mm) clevis pin 7411.30 Extra 7' (2.13 m) luff foil extrusion 7411.31 Extra 7" (178 mm) connector with bushings MKIV Underdeck Unit 2 Typical Boat Length 35' - 46' (10.6-14.2 m) 5 /16", 3 /8" (8, 10 mm) -12, -17 (7.14, 8.38 mm) 5 /8" (15.9 mm) Headstay Length Standard 60'4" (18.38 m); max 67'4" (20.51 m) 7412.11 5/8 Furling system with 5 /8" (15.9 mm) clevis pin 7412.30 Extra 7' (2.13 m) luff foil extrusion 7412.31 Extra 9" (229 mm) connector with bushings All MKIV Underdeck Furlers feature a ball bearing halyard swivel 7410.30 7411.30 7412.30 7413.30 7410.31 7411.31 7412.31 7413.31 7410.11 MKIV Underdeck Unit 3 Typical Boat Length 45' - 60' (13.7-18.3 m) 7 /16", 1 /2" (11, 12 mm) -22, -30 (9.53, 11.10 mm) 3 /4", 7 /8" (19.1, 22.2 mm) Headstay Length Standard 75'1" (22.88 m); max 82'1" (25.02 m) 7413.11 3/4 Furling system with 3 /4" (19.1 mm) clevis pin 7413.11 7/8 Furling system with 7 /8" (22.2 mm) clevis pin 7413.30 Extra 7' (2.13 m) luff foil extrusion 7413.31 Extra 9 3 /4" (248 mm) connector with bushings A B Dimensions A C Part Min Max B Min Max Unit No. in mm in mm in mm in mm in mm 0 7410.11 6 7 /8 175 5 30.4 1 7411.11 1/2 10 5 /8 270 15 5 /8 397 5 1 /2 140 4 5 /8 117 9 5 /8 244 2 7412.11 5/8 12 11 /16 322 18 9 /16 471 6 5 /8 167 5 3 /8 137 11 5 /16 287 3 7413.11 3/4 16 1 /8 410 23 5 /8 600 8 3 /16 208 6 7 /8 175 14 3 /8 365 3 7413.11 7/8 16 9 /16 421 24 1 /4 616 8 3 /16 208 7 5 /16 186 15 381 A 7411.11 1/2 7412.11 5/8 7413.11 3/4 7413.11 7/8 B C 176

ESP Jib Reefing & Furling 1 FOR CRUISING SAILORS The ESP is designed for the cruiser looking for an easy-to-assemble furler with an elegant design. Install a Harken ESP furler and trim safely from the cockpit when it blows; unfurl instead of motoring when it s light, for a great day of sailing. 2 DETAILS MAKE THE DIFFERENCE 3 EASY ASSEMBLY AND INSTALLATION Foils slip over the standard marine eye and headstay wire for easy installation. The adjustable bottom foil fine-tunes the system length. Shackles at the tack and head attach the sail to the furler, with sail shape controlled by halyard tension. There is no need to cut the wire during installation. STANDS UP TO ELEMENTS Spool is made from Hard Lube-anodized aluminum. Cover, flange, and guard are molded from glass-reinforced polymers for high strength. Foils are clear-anodized for durability. The stainless steel sail feeder is strong and durable. LONG, MEDIUM, OR SHORT LEG KITS TO ADJUST DRUM HEIGHT Medium and long leg kits raise the drum to clear the anchor, reduce sail chafe, and increase visibility. Removable clamp screws allow legs to pivot out of the way for easy access to the turnbuckle. Choose the long leg kit when using a turnbuckle with swage, Norseman or Sta-Lok terminals. Medium leg kits work with a variety of turnbuckles; refer to height chart on unit pages. Choose the short leg kit when the furler attaches directly to a marine eye at the bottom of the stay. Short legs allow the sail to be closer to the deck. OPTIONS An optional halyard deflector, installed above the foil, prevents the jib halyard and other halyards (such as a spinnaker or additional jib halyards) from wrapping around the foil when furling. Strong, lightweight stanchion-mounted blocks are offered to lead line aft for safe furling from the cockpit. Line not included. 1. Single-Groove Round Foil Round foil profile withstands extreme reefing loads for secure furling. Rolls more easily than flat foil shapes. 2. Strong Foil Joints Tough foil joints withstand years of torque loading. Connector interlocks with foil and secures with screws. No extra adhesive needed for a secure lock. 3. Long, Medium, or Short Leg Kits Choose long or medium leg kits for furlers with turnbuckles. Check turnbuckle length to determine which leg kit length is required. Choose short leg kits when furler attaches directly to a marine eye fitted to the end of the stay. DO NOT use Harken equipment for human suspension. Sta-Lok is a registered trademark of Sta-Lok Terminals, Ltd. 177

HFG594 7420-4 HFG233 7421-8 Optional 7422-8 7423-10 OPTIONAL PARTS 7320.31 7321.31 7320.30 7321.30 178 ESP Unit 0 Typical Boat Length 6-8.5 m (20' - 28') Wire Ø Rod Ø Clevis pin Ø 4, 5 mm ( 5 /32", 3 /16") -4 (4.37 mm) 8 mm, 9.5 mm ( 5 /16", 3 /8") Headstay Length* Standard 10.92 m (35'10"); max 12.92 m (42'5") 7320.10 Furling system Leg Kit Required - order separately See toggle and rigging options page 182 7320.20 5/16** Short leg kit with toggle with 8 mm ( 5 /16") clevis pin. Not for turnbuckle 7320.20 3/8** Short leg kit with toggle with 9.5 mm ( 3 /8") clevis pin. Not for turnbuckle 7320.21 5/16 Long leg kit with toggle with 8 mm ( 5 /16") clevis pin 7320.21 3/8 Long leg kit with toggle with 9.5 mm ( 3 /8") clevis pin 7320.30 Extra 2 m (6.5') luff foil extrusion 7320.31 Extra 216 mm (8.5") standard connector with bushings 7420-4 -4 rod adaptor stud (thread Ø UNF 7 /16") HFG594 7 mm x 16.8 m (55') polyester double braid line. Line not included *When using long leg kits add.13 m (5"). **Use without turnbuckle. Use with conventional turnbuckle. To use own line, figure 2 X boat length. ESP Unit 1 Typical Boat Length 7.9-10.6 m (26' - 35') Wire Ø Rod Ø Clevis pin Ø 6, 7, 8 mm ( 7 /32", 1 /4", 9 /32", 5 /16") -6, -8, -10 (5.03, 5.72, 6.35 mm) 11, 12.7 mm ( 7 /16", 1 /2") Headstay Length* Standard 13 m (42'7"); max 17 m (55'8") 7321.10 Furling system Leg Kit Required - order separately See toggle and rigging options page 182 7321.20 7/16** Short leg kit with toggle with 11 mm ( 7 /16") clevis pin. Not for turnbuckle 7321.20 1/2** Short leg kit with toggle with 12.7 mm ( 1 /2") clevis pin. Not for turnbuckle 7321.22 7/16 Medium leg kit with toggle with 11 mm ( 7 /16") clevis pin 7321.22 1/2 Medium leg kit with toggle with 12.7 mm ( 1 /2") clevis pin 7321.21 7/16 Long leg kit with toggle with 11 mm ( 7 /16") clevis pin 7321.21 1/2 Long leg kit with toggle with 12.7 mm ( 1 /2") clevis pin 7321.30 Extra 2 m (6.5') luff foil extrusion. Order 1 for stay lengths to 15.22 m (49'11")* Order 2 for stay lengths to 17.22 m (56'6")* 7321.31 Extra 229 m (9") standard connector with bushings. Order 1 for stay lengths to 15.22 m (49'11")* Order 2 for stay lengths to 17.22 m (56'6")* 7421-6 -6 rod adaptor stud (thread Ø UNF 7 /16") 7422-8 -8 rod adaptor stud (thread Ø UNF 1 /2") 7423-10 -10 rod adaptor stud (thread Ø UNF 1 /2") HFG233 7 mm x 21.3 m (70') polyester double braid line. Line not included *Add for longer leg kits. Medium leg.095 m (3 3 /4") Long leg.22 m (8 1 /2"). **Use without turnbuckle. Use with conventional turnbuckle. Check maximum turnbuckle length for medium leg kit. To use own line, figure 2 X boat length. Pin-to-pin measurement points Medium Leg Kit Max turnbuckle length Medium leg kit 7321.22 7/16 7321.22 1/2 271 mm 10 5 /8" Long leg kit Short leg kit 7320.20 5/16 7320.20 3/8 7321.20 7/16 7321.20 1/2 7320.21 5/16 7320.21 3/8 7321.21 7/16 7321.21 1/2

Optional HFG235 OPTIONAL PARTS 7424-12 7425-17 7426-22 7427-30 7428-40 7322.31 7323.31 ESP Unit 2 Typical Boat Length 10.4-14 m (34' - 46') Wire Ø Rod Ø Clevis pin Ø 8, 10, 12 mm ( 5 /16", 3 /8", 7 /16") -12-17, -22 (7.14, 8.38, 9.53 mm) 15.9, 19.1 mm ( 5 /8", 3 /4") Headstay Length* Standard 17.05 m (55'11"); max 21.05 m (69') 7322.10 Furling system Leg Kit Required - order separately See toggle and rigging options page 182 7322.20 5/8** Short leg kit with toggle with 15.9 mm ( 5 /8") clevis pin. Not for turnbuckle 7322.20 3/4** Short leg kit with toggle with 19.1 mm ( 3 /4") clevis pin. Not for turnbuckle 7322.22 5/8 Medium leg kit with toggle with 15.9 mm ( 5 /8") clevis pin. 7322.22 3/4 Medium leg kit with toggle with 19.1 mm ( 3 /4") clevis pin. 7322.21 5/8 Long leg kit with toggle with 15.9 mm ( 5 /8") clevis pin 7322.21 3/4 Long leg kit with toggle with 19.1 mm ( 3 /4") clevis pin 7322.30 Extra 2 m (6.5') luff foil extrusion. Order 1 for stay lengths to 19.33 m (63'5")* Order 2 for stay lengths to 21.33 m (70')* 7322.31 Extra 24 cm (9.5") standard connector with bushings. Order 1 for stay lengths to 19.33 m (63'5")* Order 2 for stay lengths to 21.33 m (70')* 7424-12 -12 rod adaptor stud (thread Ø UNF 5 /8") 7425-17 -17 rod adaptor stud (thread Ø UNF 5 /8") 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4") HFG235 8 mm x 30.5 m (100') polyester double braid line. Line not included *Add to length for longer leg kits. Medium Leg.175 m (7") Long Leg.305 m (12"). **Use without turnbuckle. Use with conventional turnbuckle. Check maximum turnbuckle length for medium leg kit. To use own line figure 2 X boat length. ESP Unit 3 Typical Boat Length 13.7-18.6 m (45' - 61') Wire Ø Rod Ø Clevis pin Ø 12.7, 14, 16 mm ( 1 /2", 9 /16", 5 /8") -22, -30, -40 (9.53, 11.10, 12.7 mm) 22.2, 25.4 mm ( 7 /8", 1") Headstay Length* Standard 21.15 m (69'5"); max 25.15 m (82'7") 7323.10 Furling system Leg Kit Required - order separately See toggle and rigging options page 182 7323.20 7/8** Short leg kit with toggle with 22.2 mm ( 7 /8") clevis pin. Not for turnbuckle 7323.20 1** Short leg kit with toggle with 25.4 mm (1") clevis pin. Not for turnbuckle 7323.22 7/8 Medium leg kit with toggle with 22.2 mm ( 7 /8") clevis pin. 7323.22 1 Medium leg kit with toggle with 25.4 mm (1") clevis pin. 7323.21 7/8 Long leg kit with toggle with 22.2 mm ( 7 /8") clevis pin 7323.21 1 Long leg kit with toggle with 25.4 mm (1") clevis pin 7323.30 Extra 2 m (6.5') luff foil extrusion. Order 1 for stay lengths to 23.5 m (77'1")* Order 2 for stay lengths to 25.5 m (83'8")* 7323.31 Extra 26.7 cm (10.5") standard connector. Order 1 for stay lengths to 23.5 m (77'1")* Order 2 for stay lengths to 25.5 m (83'8")* 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4") 7427-30 -30 rod adaptor stud (thread Ø UNF 7 /8") 7428-40 -40 rod adaptor stud (thread Ø UNF 1") *Use 7/16" (10, 12 mm) polyester double braid line not supplied by Harken. To figure line length use 2 X boat length *Add to length for longer leg kits. Medium leg.215 m (8 1 /2") Long leg.37 m (14 1 /2"). **Use without turnbuckle. Use with conventional turnbuckle. Check maximum turnbuckle length for medium leg kit. Pin-to-pin measurement points Medium Leg Kit Max turnbuckle length Medium leg kit 7322.30 7323.30 7322.22 5/8 7322.22 3/4 7323.22 7/8 7323.22 1 Unit 2 411 mm 16 1 /8" Unit 3 489 mm 19 1 /4" Long leg kit 7322.20 5/8 7322.20 3/4 7323.20 7/8 7323.20 1 7322.21 5/8 7322.21 3/4 7323.21 7/8 7323.21 1 Short leg kit 179

Electric Jib Reefing & Furling PUSH-BUTTON SAIL CONTROL Designed for large cruising boats, electric furling is a headsail system that helps you get the most out of your boat, while letting you comfortably reef, furl, and set sails from the cockpit with the push of a button. 1 2 3 4 DETAILS MAKE THE DIFFERENCE HIGH-STRENGTH MATERIALS, SCULPTED DESIGN The torque tube, motor, and gear housing are deep-saturation hardcoat-anodized, UV-stabilized aluminum. The sculpted gearbox and streamlined motor housing are sealed with high quality lip seals and O rings. The motor mounts vertically into pulpits, clearing anchor tackle and providing low windage. HIGH-TORQUE, HIGH-EFFICIENCY MOTOR The motor is a permanent magnet design and features high torque and low power consumption. Inside, the hardened steel gears are permanently lubricated. The reversible drive uses a high-reduction worm gear set to prevent reefed sails from unfurling under load. 1. Strong Foil Joints Tough triple-interlock foil joints withstand years of torque loading. 2. 12- or 24-Volt Systems Available in 12 or 24 volts; switches and 12- or 24-volt control box and circuit breaker included. 3. Emergency Manual Operation Use supplied crank handle or cordless drill adapter. 4. Scratch-Resistant Link Plates Stainless steel link plates fit over standard turnbuckle, resist scratches, and can be easily repolished. EASY TO INSTALL OR UPGRADE C-shaped connectors slip over the headstay without feeding wire through the connector. The lower unit fits over the existing turnbuckle allowing easy length adjustment. Easy upgrade from a MKIV Unit 2 and 3 manual unit. 180 DO NOT use Harken equipment for human suspension.

NEW 7406 Unit 2E Typical Boat Length 10.6-14.2 m (35' - 46') 8, 10 mm ( 5 /16", 3 /8") -12-17, -22 (7.14, 8.38, 9.53 mm) 15.9, 19.1 mm ( 5 /8", 3 /4") Headstay Length Standard 18.57 m (60'11"); max 20.70 m (67'11") 7412.13 12V Furling system 12-volt with control box, switches, and circuit breaker 7412.13 24V Furling system 24-volt with control box, switches, and circuit breaker 7312.22 5/8 Jaw/jaw with link plate with 15.9 mm ( 5 /8") clevis pin 7413.22 3/4 Jaw/jaw with link plate with 19.1 mm ( 3 /4") clevis pin 7406 Through-deck fitting for power cable 7412.12V.CONV Conversion kit MKIV manual to 12V-electric* 7412.24V.CONV Conversion kit MKIV manual to 24V-electric* 7412.30 Extra 2.13 m (7') luff foil extrusion 7412.31 Extra 229 mm (9") connector with bushings 7424-12 -12 rod adaptor stud (thread Ø UNF 5 /8")** 7425-17 -17 rod adaptor stud (thread Ø UNF 5 /8")** 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4")** *Includes switches and 12- or 24-volt control box and circuit breaker. Requires toggle assembly. ** Use with conventional turnbuckle. 7412.13 12V 7412.13 24V C Halyard shackle A Head shackle B Unit 3E Typical Boat Length 13.7-18.3 m (45' - 60') 11, 12 mm ( 7 /16", 1 /2") -22, -30 (9.53, 11.10 mm) 19.1, 22.2 mm ( 3 /4", 7 /8") Headstay Length Standard 22.88 m (75'1"); max 25.02 m (82'1") 7413.13 12V Furling system 12-volt with control box, switches, and circuit breaker 7413.13 24V Furling system 24-volt with control box, switches, and circuit breaker 7413.22 3/4 Jaw/jaw with link plate with 19.1 mm ( 3 /4") clevis pin 7413.22 7/8 Jaw/jaw with link plate with 22.2 mm ( 7 /8") clevis pin 7406 Through-deck fitting for power cable 7413.12V.CONV Conversion kit MKIV manual to 12V-electric* 7413.24V.CONV Conversion kit MKIV manual to 24V-electric* 7413.30 Extra 2.13 m (7') luff foil extrusion 7413.31 Extra 248 mm (9 3 /4") connector with bushings 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4")** 7427-30 -30 rod adaptor stud (thread Ø UNF 7 /8")** * Includes switches and 12- or 24-volt control box and circuit breaker. Requires toggle assembly. **Use with conventional turnbuckle. Tack shackle G F E D H 7406 Foil Dimensions 7412.31 7413.31 Electric Furler Dimensions 7412.30 7413.30 7424-12 7425-17 7426-22 7427-30 J K Foil length Unit in mm in mm ft m Luff tape* 2E 1 1 /4 32 1 3 /8 36 7 2.13 #6 5 mm ( 6 /32") 3E 1 1 /2 38 1 11 /16 43 7 2.13 #6 5 mm ( 6 /32") *Nominal dimensions only, actual luff tape dimensions are larger. 7312.22 5/8 7413.22 3/4 7413.22 7/8 K 7413.13 12V 7413.13 24V J Unit 2E, 3E Part A B C D E F G H No. in mm in mm in mm in mm in mm in mm in mm in mm 7412.13 with 7312.22 5/8 toggle 5 3 /8 143 9 1 /8 231 3 1 /4 82 33 1 /16 841 24 1 /2 622 22 5 /8 574 4 1 /2 116 8 11 /32 212 7412.13 with 7413.22 3/4 toggle 5 3 /8 143 9 1 /8 231 3 1 /4 82 33 11 /19 856 25 3 /32 637 23 1 /4 590 5 3 /16 132 8 11 /32 212 7413.13 with 7413.22 3/4 toggle 7 5 /16 186 11 5 /8 296 3 1 /4 82 32 1 /2 826 25 3 /32 637 23 1 /4 590 5 3 /16 132 8 11 /32 212 7413.13 with 7413.22 7/8 toggle 7 5 /16 186 11 5 /8 296 3 1 /4 82 33 3 /16 840 25 11 /16 652 23 13 /16 605 5 3 /4 146 8 11 /32 212 181

Toggle & Rigging Options Use these rigger-supplied options to fit Harken toggles and leg kits shown below. Harken toggle and leg kit assemblies sold separately. See unit pages. Model MKIV Toggle Clevis Pin Ø in mm 7311.20 1/2 Jaw/jaw 1 /2 12.7 7311.21 1/2 Long link plate w/toggle 1 /2 12.7 7311.21 5/8 Long link plate w/toggle 5 /8 15.9 7312.20 5/8 Jaw/jaw 5 /8 15.9 7312.21 5/8 Long link plate w/toggle 5 /8 15.9 7312.21 3/4 Long link plate w/toggle 3 /4 19.1 7413.20 3/4 Jaw/jaw w/short link plate 3 /4 19.1 7413.20 7/8 Jaw/jaw w/short link plate 7 /8 22.2 7313.21 3/4 Long link plate w/toggle 3 /4 19.1 7313.21 7/8 Long link plate w/toggle 7 /8 22.2 7414.20 7/8 Jaw/jaw w/short link plate 7 /8 22.2 7414.20 1 Jaw/jaw w/short link plate 1 25.4 7414.20 1 1/8 Jaw/jaw w/short link plate 1 1 /8 28.57 Fits Unit Furler Part No. 1 7411.10 2 7412.10 3 7413.10 4 7414.10 Rigger Supplied Harken Long link plate w/toggle Jaw/jaw toggle assembly MKIV 7410.20 5/16 Eye/jaw (reversible) 5 /16 7.9 7410.20 3/8 Eye/jaw (reversible) 3 /8 9.5 0 7410.10 7410.20 7/16 Eye/jaw (reversible) 7 /16 11.1 7411.20 1/2 Eye/jaw (reversible) 1 /2 12.7 1 7411.10 7412.20 5/8 Eye/jaw (reversible) 5 /8 15.9 2 7412.10 Eye/jaw toggle assembly Stud/jaw toggle assembly MKIV ELECTRIC HYDRAULIC 7311.20 5/8 Stud/jaw* 5 /8 15.9 1 7411.10 7312.20 3/4 Stud/jaw** 3 /4 19.1 2 7412.10 *Thread Ø: 5 /8 18 LH **Thread Ø: 3 /4 16 LH Toggle flips for alternate chainplate position. 7312.22 5/8 Jaw/jaw w/ link plate 5 /8 15.9 7413.22 3/4 Jaw/jaw w/ link plate 3 /4 19.1 7413.22 3/4 Jaw/jaw w/ link plate 3 /4 19.1 7413.22 7/8 Jaw/jaw w/ link plate 7 /8 22.2 741X.25 X/X Hydraulic furling toggles 3 /4 2 7 /16 19.9 61.9 741X.26 X/X Furling toggles and cylinders 3 /4 2 7 /16 19.9 61.9 2E 3E 7312.13 12V/24V 7413.13 12V/24V 3H - 8H 741X.15 Boats with larger clevis pins use special Harken lower stud fitting. Hydraulic 7320.20 5/16 Short leg kit* 5 /16 8 7320.20 3/8 Short leg kit* 3 /8 9.5 7320.21 5/16 Long leg kit 5 /16 8 0 7320.10 7320.21 3/8 Long leg kit 3 /8 9.5 7321.20 7/16 Short leg kit* 7 /16 11 7321.20 1/2 Short leg kit* 1 /2 12.7 7321.22 7/16 Medium leg kit** 7 /16 11 7321.22 1/2 Medium leg kit** 1 /2 12.7 1 7321.10 7321.21 7/16 Long leg kit 7 /16 11 7321.21 1/2 Long leg kit 1 /2 12.7 7322.20 5/8 Short leg kit* 5 /8 15.9 7322.20 3/4 Short leg kit* 3 /4 19.1 7322.22 5/8 Medium leg kit** 5 /8 15.9 7322.22 3/4 Medium leg kit** 3 /4 19.1 2 7322.10 7322.21 5/8 Long leg kit 5 /8 15.9 7322.21 3/4 Long leg kit 3 /4 19.1 7323.20 7/8 Short leg kit* 7 /8 22.2 7323.20 1 Short leg kit* 1 25.4 7323.22 7/8 Medium leg kit** 7 /8 22.2 7323.22 1 Medium leg kit** 1 25.4 3 7323.10 7323.21 7/8 Long leg kit 7 /8 22.2 7323.21 1 Long leg kit 1 25.4 *Marine eye only. Does not fit turnbuckle. **Check maximum turnbuckle length for medium leg kit. See unit pages 178-179. 182 ESP Electric Hydraulic Short leg kit* Medium leg kit** Long leg kit

MKIV Hydraulic Jib Reefing and Furling 1 PUSH-BUTTON SAIL CONTROL Harken MKIV Hydraulic Jib Reefing and Furling systems allow sails to be reefed, furled, or set with the touch of a button. The unit s compact size brings the sail s tack close to the deck for smoother furling and improved sail shape. Both tack and head have independent swivels, improving sail shape when partially reefed. MKIV hydraulic furlers are used on cruisers and performance cruisers with headstays up to -320 rod or equivalent fiber stay. Worldwide parts and service. 2 DETAILS MAKE THE DIFFERENCE STANDARD TRANSMISSION REDUCES FRICTION AND PRESSURE LOSS A standard transmission, rather than a diverter valve, engages and disengages the powered and manual gear drive. Reduces mechanical friction and hydraulic pressure loss for efficient power and manual operation. The motor has no case drain line, reducing the number of hoses plumbed on the boat from three to two. Worm gear drive prevents backwinding and unloads the hydraulic motor when reefed. LONG-LASTING MATERIALS Torque tube, motor, and gear housing are hardcoatanodized aluminum for long-term wear and UVstabilized to withstand the effects of saltwater and sun. Aluminum foils are clear-anodized. Large-diameter Torlon ball bearings in halyard and tack swivel minimize friction, require no lubrication or isolating seals. Hardened steel gears and bearings are permanently lubricated in an oil bath for minimal maintenance. 1. Easy Headstay Adjustment Over-the-turnbuckle system allows easy headstay adjustment. The lower toggle assembly fixes at 90-degree intervals to accept any chainplate direction. 2. Optional Hydraulic Cylinder An optional hydraulic cylinder installed below the unit adjusts the headstay so luff tension remains constant. This prevents halyard and tack attachments from overloading when the headstay is adjusted. 3. Improved Sail Shape Independent head and tack swivels improve sail shape when reefed. Hard and Soft Attachments Unit 3 uses a hard shackle; halyard and tack swivels on Units 4 and larger are lashed on with Spectra line using a patented system to evenly distribute loads and eliminate heavy shackles. 4. Double Foil Grooves Aerodynamic aluminum sections handle extreme reefing loads. Double luff grooves allow fast hoists, douses, and sail changes. 5. Carbon Foils Contact Harken for availability and price. 3 4 5 DO NOT use Harken equipment for human suspension. Torlon is a registered trademark of Solvay Advanced Polymers. Spectra is a registered trademark of Honeywell International, Inc. 183

MKIV Hydraulic Jib Reefing & Furling 7413.30 7414.30 7413.31 7414.31S 7414.31L Contact Harken for availability of carbon foils. 7426-22 7427-30 7428-40 7429-48 7413.25 3/4 7413.25 7/8 7414.25 7/8 7414.25 1 7414.25 1 1/8 7413.26 3/4 7413.26 7/8 7414.26 7/8 7414.26 1 7414.26 1 1/8 Manual operation switch and gear socket. Unit 3 11, 12 mm ( 7 /16", 1 /2") -22, -30 (9.53, 11.10 mm) 19, 22.2 mm ( 3 /4", 7 /8") Headstay Length* Aluminum foil: standard 22.77 m (74'9"), max 24.91 m (81'9") 7413.15 Furling system with aluminum foils 7413.25 3/4 Toggle for 19 mm ( 3 /4") clevis pin 7413.25 7/8 Toggle for 22.2 mm ( 7 /8") clevis pin 7413.26 3/4 Toggle and hydraulic cylinder for 19 mm ( 3 /4") clevis pin 7413.26 7/8 Toggle and hydraulic cylinder for 22.2 mm ( 7 /8") clevis pin 7413.30 Extra 2.13 m (7') aluminum foil extrusion 7413.31 Extra 248 mm (9 3 /4") connector with bushings 7426-22 -22 rod adaptor stud (thread Ø UNF 3 /4")** 7427-30 -30 rod adaptor stud (thread Ø UNF 7 /8")** Contact Harken to request quote and lead time. *Hydraulic cylinder increases standard and maxiumum lengths. **Use with conventional turnbuckle. Unit 4 12, 14, 16 mm ( 1 /2", 9 /16", 5 /8") -30, -40, -48 (11.10, 12.7, 14.3 mm) 22.2, 25.4, 28.6 mm ( 7 /8", 1", 1 1 /8") Headstay Length* Alumiunum foil: standard 22.93 m (75'3"), max 29.33 m (96'3") 7414.15S Furling system with aluminum foils and small bushing; fits -30, -40 rod, 12 mm ( 1 /2") wire 7414.15L Furling system with aluminum foils and large bushing; fits -48 rod, 14 mm, 16 mm ( 9 /16", 5 /8") wire 7414.25 7/8 Toggle for 22.2 mm ( 7 /8") clevis pin 7414.25 1 Toggle for 25.4 mm (1") clevis pin 7414.25 1 1/8 Toggle for 28.6 mm (1 1 /8") clevis pin 7414.26 7/8 Toggle and hydraulic cylinder for 22.2 mm ( 7 /8") clevis pin 7414.26 1 Toggle and hydraulic cylinder for 25.4 mm (1") clevis pin 7414.26 1 1/8 Toggle and hydraulic cylinder for 28.6 mm (1 1 /8") clevis pin 7414.30 Extra 2.13 m (7') aluminum foil extrusion 7414.31S Extra 10 3 /4" (270 mm) connector with bushings, fits -30, -40 rod, 12 mm ( 1 /2") wire 7414.31L Extra 10 3 /4" (270 mm) connector with bushings, fits fits -48 rod, 14 mm, 16 mm ( 9 /16", 5 /8") wire 7427-30 -30 rod adaptor stud (thread Ø UNF 7 /8")** 7428-40 -40 rod adaptor stud (thread Ø UNF 1")** 7429-48 -48 rod adaptor stud (thread Ø UNF 1 1 /8")** Contact Harken to request quote and lead time. *Hydraulic cylinder increases standard and maximum lengths. 184 **Use with conventional turnbuckle. Unit 3 Unit 4 Unit 3 Unit 4

MKIV Hydraulic Jib Reefing & Furling 7415.30 7416.30 Unit 5 Contact Harken for availability of carbon foils. 7415.31S 7415.31M 7415.31L 7416.31S 7416.31M 7416.31L 7429-48 7415.25 1 1/8 7415.25 1 1/4 7415.25 X X/X 7416.25 1 1/4 7416.25 1 3/8 7416.25 1 9/16 7416.25 X X/X 7415.26 1 1/8 7415.26 1 1/4 7415.26 X X/X 7416.26 1 1/4 7416.26 1 3/8 7416.26 1 9/16 7416.26 X X/X 16, 19, 22 mm ( 5 /8", 3 /4", 7 /8") -48, -60, -76 (14.3, 16.8, 17.9 mm) 28.6, 31.8 mm (1 1 /8", 1 1 /4") Headstay Length* 7415.15S aluminum foil: standard 23.8 m (78'), max 34.7 m (114'); 7415.15M and 7415.15L aluminum foil: standard 26.5 m (87'), max 34.7 m (114') 7415.15S Furling system with aluminum foils and small bushing; fits -48, -60 rod, 16 mm ( 5 /8") wire 7415.15M Furling system with aluminum foils and medium bushing: fits -76 7415.15L Furling system with aluminum foils and large bushing; fits 19, 22 mm ( 3 /4", 7 /8") wire 7415.25 1 1/8 Toggle for 28.6 mm (1 1 /8") clevis pin 7415.25 1 1/4 Toggle for 31.8 mm (1 1 /4") clevis pin 7415.25 X X/X** Toggle for all other clevis pin sizes (customer supplied dimensions) 7415.26 1 1/8 Toggle and hydraulic cylinder for 28.6 mm (1 1 /8") clevis pin 7415.26 1 1/4 Toggle and hydraulic cylinder for 31.8 mm (1 1 /4") clevis pin 7415.26 X X/X** Toggle and hydraulic cylinder for all other clevis pin sizes (customer supplied dimensions) 7415.30 Extra 2.74 m (9') aluminum foil extrusion 7415.31S Extra 305 mm (12") connector with small bushing; fits -48, -60 rod, 16 mm (5/8") wire 7415.31M Extra 305 mm (12") connector with medium bushing; fits -76 rod 7415.31L Extra 305 mm (12") connector with large bushing; fits 19, 22 mm ( 3 /4", 7 /8") wire 7429-48 -48 rod adaptor stud (thread Ø UNF 1 1 /8")*** Contact Harken to request quote and lead time. *Hydraulic cylinder increases standard and maximum lengths. Continuous rod only. If rod is sectional, order Unit 6. **Specify rigging dimensions when ordering. ***Use with conventional turnbuckle. Unit 6 22, 25 mm (7/8", 1") -76, -91, -115 (17.9, 19.5, 22.2 mm) 31.8, 34.9, 39.7 mm (1 1 /4", 1 3 /8", 1 9 /16") Headstay Length* Aluminum foil: standard 28.8 m (94'6"), max 38.8 m (127'6") 7416.15S Furling system with aluminum foils and small bushing; fits -76 rod 7416.15M Furling system with aluminum foils and medium bushing; fits -91 rod 7416.15L Furling system with aluminum foils and large bushing; fits -115 rod, 22, 25 mm ( 7 /8", 1") wire 7416.25 1 1/4 Toggle for 31.8 mm (1 1 /4") clevis pin 7416.25 1 3/8 Toggle for 34.9 mm (1 3 /8") clevis pin 7416.25 1 9/16 Toggle for 39.7 mm (1 9 /16") clevis pin 7416.25 X X/X** Toggle for all other clevis pin sizes (customer supplied dimensions) 7416.26 1 1/4 Toggle and hydraulic cylinder for 31.8 mm (1 1 /4") clevis pin 7416.26 1 3/8 Toggle and hydraulic cylinder for 34.9 mm (1 3 /8") clevis pin 7416.26 1 9/16 Toggle and hydraulic cylinder for 39.7 mm (1 9 /16") clevis pin 7416.26 X X/X** Toggle and hydraulic cylinder for all other clevis pin sizes (customer supplied dimensions) 7416.30 Extra 3.35 m (11') aluminum foil extrusion 7416.31S Extra 330 mm (13") connector with small bushing; fits -76 rod 7416.31M Extra 330 mm (13") connector with medium bushing; fits -91 rod 7416.31L Extra 330 mm (13") connector with large bushing; fits -115 rod, 22, 25 mm ( 7 /8", 1") wire Contact Harken to request quote and lead time. *Hydraulic cylinder increases standard and maximum lengths. **Specify rigging dimensions when ordering. Unit 4 Unit 5 Unit 6 185

MKIV Hydraulic Jib Reefing & Furling 7417.30 7418.30 Contact Harken for availability of carbon foils. 7417.25 1 9/16 7417.25 1 3/4 7417.25 1 7/8 7417.31S 7417.25 X X/X 7417.31M 7418.25 1 7/8 7417.31L 7418.25 2 1/8 7418.31 7418.25 2 1/4 7418.25 2 7/16 7418.25 X X/X Unit 7Fiber Stay Rod Ø Clevis pin Ø 7417.26 1 9/16 7417.26 1 3/4 7417.26 1 7/8 7417.26 X X/X 7418.26 1 7/8 7418.26 2 1/8 7418.26 2 1/4 7418.26 2 7/16 7418.26 X X/X Customer-supplied dimensions -115, -150, -170 (22.2, 25.4, 27.1 mm) 39.7, 44.5, 47.6 mm (1 9 /16", 1 3 /4", 1 7 /8") Headstay Length Aluminum foil: contact Harken with stay length 7417.15S Furling system with aluminum foils and small bushing; fits -115 rod 7417.15M Furling system with aluminum foils and medium bushing; fits -150 rod 7417.15L Furling system with aluminum foils and large bushing; fits -170 rod 7417.15 X.XXX** Furling system with aluminum foils for all other rigging (customer-supplied dimensions) 7417.25 1 9/16 Toggle for 39.7 mm (1 9 /16") clevis pin 7417.25 1 3/4 Toggle for 44.5 mm (1 3 /4") clevis pin 7417.25 1 7/8 Toggle for 47.6 mm (1 7 /8") clevis pin 7417.25 X X/X** Toggle for all other clevis pin sizes (customer-supplied dimensions) 7417.26 1 9/16 Toggle and hydraulic cylinder for 39.7 mm (1 9 /16") clevis pin 7417.26 1 3/4 Toggle and hydraulic cylinder for 44.5 mm (1 3 /4") clevis pin 7417.26 1 7/8 Toggle and hydraulic cylinder for 47.6 mm (1 7 /8") clevis pin 7417.26 X X/X** Toggle and hydraulic cylinder for all other clevis pin sizes (customer-supplied dimensions) 7417.30 Extra 3.96 m (13') aluminum foil extrusion 7417.31S Extra connector with small bushings; fits -115 rod 7417.31M Extra connector with medium bushings; fits -150 rod 7417.31L Extra connector with large bushings; fits -170 rod Contact Harken to request quote and lead time. **Specify rigging dimensions when ordering. Unit 8Fiber Stay Rod Ø Clevis pin Ø Customer-supplied dimensions -170, -195, -220, -260, -320 47.6, 54.0, 57.2, 61.9 mm (27.1, 28.6, 30.3, 33.4, 38.10 mm) (1 7 /8", 2 1 /8", 2 1 /4", 2 7 /16") Headstay Length Aluminum foil: contact Harken with stay length 7418.15 Furling system with aluminum foils 7418.15 X.XXX** Furling system with aluminum foils for all other rigging (customer-supplied dimensions) 7418.25 1 7/8 Toggle for 47.6 mm (1 7 /8") clevis pin 7418.25 2 1/8 Toggle for 54.0 mm (2 1 /8") clevis pin 7418.25 2 1/4 Toggle for 57.2 mm (2 1 /4") clevis pin 7418.25 2 7/16 Toggle for 61.9 mm (2 7 /16") clevis pin 7418.25 X X/X** Toggle for all other clevis pin sizes (customer-supplied dimensions) 7418.26 1 7/8 Toggle and hydraulic cylinder for 47.6 mm (1 7 /8") clevis pin 7418.26 2 1/8 Toggle and hydraulic cylinder for 54.0 mm (2 1 /8") clevis pin 7418.26 2 1/4 Toggle and hydraulic cylinder for 57.2 mm (2 1 /4") clevis pin 7418.26 2 7/16 Toggle and hydraulic cylinder for 61.9 mm (2 7 /16") clevis pin 7418.26 X X/X** Toggle and hydraulic cylinder for all other clevis pin sizes (customer-supplied dimensions) 7418.30 Extra 3.96 m (13') aluminum foil extrusion 7418.31 Extra connector with bushings Contact Harken to request quote and lead time. **Specify rigging dimensions when ordering. 186 Unit 7 Unit 8

Hydraulic Furling Dimensions Contact Harken for furler dimensions larger than Unit 6. E** A B C D* Max Min Unit in mm in mm in mm in mm in mm in mm 3 7 5 /16 186 12 300 8 1 /4 209 3 1 /4 80 47 9 /16 1209 47 1194 4 8 15 /16 227 14 1 /4 360 8 7 /8 225 4 1 /2 115 55 1 /2 1409 54 3 /8 1381 5 10 1 /2 267 17 430 10 3 /8 264 5 120 63 1 /2 1613 62 13 /16 1596 6 12 1 /2 314 20 1 /2 520 11 3 /16 285 6 1 /4 160 67 3 /8 1711 66 1 /16 1679 *From boltrope **If hydraulic cylinder is used, dimensions E through I will increase according to cylinder length and settings. See cylinder length addition chart. See installation manual for detailed cylinder dimension information. A B F** G** H** Max Min Max Min Max Min Unit in mm in mm in mm in mm in mm in mm 3 32 7 /8 836 32 5 /16 821 18 7 /8 480 18 1 /2 470 16 11 /16 424 16 1 /8 409 4 38 1 /4 971 37 1 /8 943 22 1 /4 565 21 1 /4 540 19 11 /16 500 18 9 /16 472 5 41 11 /16 1059 41 1042 27 1 /2 700 26 3 /4 680 24 1 /2 619 23 11 /16 602 6 46 9 /16 1183 45 1 /4 1150 30 3 /8 770 28 3 /4 730 26 1 /4 666 25 634 **If hydraulic cylinder is used, dimensions E through I will increase according to cylinder length and settings. See cylinder length addition chart. See installation manual for detailed cylinder dimension information. I** J K Max Min Max Min Max Min Unit in mm in mm in mm in mm in mm in mm 3 5 3 /16 132 4 5 /8 118 2 9 /16 65 2 51 11 9 /16 293 6 7 /8 174 4 6 5 /16 160 5 3 /16 132 3 3 /4 95 2 5 /8 66 13 7 /8 353 7 3 /8 188 5 7 1 /4 185 6 5 /8 168 4 5 /16 109 3 5 /8 91.8 15 13 /16 402 9 1 /8 232 6 8 9 /16 218 7 1 /4 185 5 7 /16 139 4 3 /16 106 18 1 /2 469 9 13 /16 249 **If hydraulic cylinder is used, dimensions E through I will increase according to cylinder length and settings. See cylinder length addition chart. See installation manual for detailed cylinder dimension information. D E Cylinder Length Addition Add min length Add max length Stroke length Unit in mm in mm in mm 3 14 7 /8 378 19 483 4 100 4 16 1 /4 413 21 5 /8 549 5 125 5 18 7 /8 479 24 7 /8 631 6 150 6 21 1 /16 535 28 7 /16 722 7 175 H G F Foil Dimensions L M Foil length Unit in mm in mm ft m Luff tape* 3 1 1 /2 38 1 11 /16 43 7 2.13 #6 5 mm ( 6 /32") 4 1 3 /4 44 1 27 /32 47 7 2.13 #6 5 mm ( 6 /32") 5 2 13 /32 61 2 5 /8 63 9 2.74 #6 5 mm ( 6 /32"), #7 6 mm ( 7 /32") 6 3 3 /16 82 3 9 /32 83 11 3.35 #6 5 mm ( 6 /32"), #7 6 mm ( 7 /32") 7 3 11 /32 98 4 101 13 3.96 #6 5 mm ( 6 /32"), #7 6 mm ( 7 /32") 8 4 1 /2 115 4 5 /8 118 13 3.96 #6 5 mm ( 6 /32"), #7 6 mm ( 7 /32") *Nominal dimensions only, actual luff tape dimensions are larger. L M C J I K Mistress, Swan 53, Nautor s Swan 187

Furling Accessories Carbo Furling Lead Block Assemblies Harken recommends equipping every system with Carbo lead blocks for safe furling from the cockpit. The 7404 kit s lightweight, UV-stabilized Carbo blocks run exclusively on ball bearings for fast trimming under any load. A 7402 ratchet maintains tension when spooling so the unit furls smoothly and easily. The 7403 outboard assembly allows the furling line to travel outboard of the stanchion to keep the sidedeck clear. Block mounts with a strong four-screw clamp without removing the stanchion or lifelines. Use the 7401 block on the bow pulpit as an inboard lead. Use the 7405 as an inboard lead for two lines, for continuous line furlers, or cutter-rigged boats with two furlers. 7401, 7402, and 7405 have ball-and-socket bases to align blocks for smooth leads aft. The 7404 lead block kit provides a complete system for most boats. Stanchion Mount Bases The 061 bases for Carbo and Classic blocks lead furling line inside the stanchion. Halyard Restrainers A halyard restrainer keeps the halyard against the mast. This provides a better angle to the halyard swivel and prevents it from wrapping around the foil. Stainless steel brackets feature hardcoat-anodized aluminum sheaves that accommodate both wire and rope. Halyard Deflector A halyard deflector prevents the jib halyard and other halyards (such as a spinnaker or additional jib halyards) from wrapping around the foil. Prefeeders and Snap Shackles Prefeeders and snap shackles facilitate fast sail changes. The 7006 prefeeder features hardcoat-anodized rollers with low-friction bushings. The 7403 outboard assembly allows furling line to travel outboard of the stanchion to keep the sidedeck clear. 7401 7402 7405 7403 448 061 944 945 7301, 7302 7303, 7304 7404 947 7006 884 885 7430 7431 188

Furling Accessories Flying Tiger 10m, Flying Tiger Boats, Robert Perry design, 10 m (32.68') Heidi Harken photo Part Sheave Ø Weight Max line Ø Maximum working load No. Description in mm oz g in mm lb kg Use with 061 Stanchion mount base* 2 57 350 159 7 /8", 1" (22, 25 mm) stanchions 448 Halyard lead block 1 1 /2 38 2.1 60 3 /8 10 300 136 0/1/2 884 Snap shackle 2.3 65 1500 680 00AL, MKIV 0/1 885 Snap shackle 5 141 2300 1040 MKIV 2 944 Halyard restrainer** 15 /16 25 3 85 00AL/0/1 945 Halyard restrainer** 1 1 /4 31 6 170 2/3/3.25 7301 Halyard deflector 1.6 45 MKIV and ESP Unit 0 7302 Halyard deflector 2.4 68 MKIV and ESP Unit 1 7303 Halyard deflector 4.8 136 MKIV and ESP Unit 2 7304 Halyard deflector 8 227 MKIV and ESP Unit 3 947 Prefeeder 1 28 All 7006 Carbo racing foil prefeeder 3 85 All 7401 40 mm Carbo lead block assembly 1 9 /16 40 3.7 106 3 /8 10 485 220 1" (25 mm) stanchions 7402 57 mm Carbo ratchet lead block assembly 2 1 /4 57 5.4 152 3 /8 10 500 227 1" (25 mm) stanchions 7403 29 mm outboard lead block assembly 1 1 /8 29 3 84 3 /8 10 1" (25 mm) stanchions 7404 Lead block kit*** Kit includes 3 x 7403 / 1 x 7401 / 1 x 7402 / 1 cleat 1" (25 mm) stanchions 7405 40 mm Carbo stanchion mount double lead 1 9 /16 40 5.6 159 3 /8 10 485 220 1" (25 mm) stanchions 7430 Powered furling crank handle 7 198 Electric/hydraulic furling 7431 Powered furling drill adapter 2.5 71 Electric/hydraulic furling *Stanchion mount base fits Classic Bullet, Big Bullet, 2.25 in, 57 mm Carbo single blocks, and ratchet blocks with swivel post. ***Max line Ø: 10 mm ( 3 /8"); Weight: 544 g (19.2 oz). **#10 RH (5 mm) fasteners. 189