ode No: 0816409 Rev. 1 (07/11) INSTLLTION INSTRUTIONS ND USER MNUL FOR SLON EF GOOSENEK SERIES FUETS EF-700 Powered, Sensor ctivated Electronic Gooseneck Hand Washing Faucets EF-750 attery Powered, Sensor ctivated Electronic Gooseneck Hand Washing Faucets LIMITED WRRNTY Unless otherwise noted, Sloan Valve ompany warrants its product, manufactured and sold for commercial for industrial uses, to be free from defects in material and workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve ompnay will, at its option repair replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve ompany, at customer s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve ompany s products directly from Sloan Valve ompany for purpose of resale. This warranty does not cover the life of the batteries. THERE RE NO WRRNTIES WHIH ExTEND EYOND THE DESRIPTION ON THE FE HEREOF. IN NO EVENT IS SLON VLVE OMPNY RESPONSILE FOR NY ONSEqUENTIL DMGES OF NY MESURE WHTSOEVER. PRIOR TO INSTLLTION Prior to installing the Sloan Optima EF-700 Series Faucets, install the items listed below. lso, refer to rough-in illustrations. Lavatory/sink Drain Line Hot/old Water Supply Lines or Tempered Supply IMPORTNT: LL PLUMING SHOULD E INSTLLED IN ORDNE WITH PPLILE ODES ND REGULTIONS. FLUSH LL WTER LINES PRIOR TO MKING ONNETIONS. KEEP THRED SELNT OUT OF YOUR WTERWY TO PREVENT OMPONENT PRT DMGE! DO NOT USE NY SELNT ON OMPRESSION FITTINGS. Trim Plates When the EF Faucet is installed on a sink that has three (3) hole punchings, a trim plate should be used. Trim Plates must be specified and ordered separately. SFP-11 Trim Plate for 4 (102 mm) enterset Sink SFP-22 Trim Plate for 8 (203 mm) enterset Sink TOOLS REQUIRED FOR INSTLLTION 13 mm open end wrench or nut driver for faucet retainer nut 5/8 open end wrench for female end of flex hose
FUET ROUGH-IN 10-1/32 (255 mm) Model EF-700/750 1.5 gpm (5.7 Lpm) Max. Flow Faucets with Hot/old Water Supply SPOUT Model EF-700/750 1.5 gpm (5.7 Lpm) Max. Flow Faucets with Tempered Water Supply SPOUT 5-7/8 (147 mm) 2-1/4 (57 mm) 24 5-11/32 (151 mm) 3-15/16 (100 mm) 2-9/16 (65 mm) O-RING GSKET RETINER NUT MIXING LEVER (N E SET ND REMOVED) 1-3/16 (30 mm) MIN. DI. HOLE REQUIRED 1-1/2 (38 mm) MX. DEK THIKNESS O-RING GSKET RETINER NUT TEMPERED SUPPLY 13 (330 mm) LONG FLEX HOSE 1-3/16 (30 mm) MIN. DI. HOLE REQUIRED 1-1/2 (38 mm) MX. DEK THIKNESS If a connection to separate hot and cold water supplies is desired, then a ak-hek tee fitting (not supplied) must be used prior to connecting to the faucet. HOT SUPPLY 13 (330 mm) LONG FLEX HOSE OLD SUPPLY When the EF faucet is installed on a sink that has three (3) hole punchings, a trim plate should be used. Trim plate must be specified and ordered separately: ETF-312- Trim Plate for 4 (102 mm) enterset Sink ETF-510- Trim Plate for 8 (204 mm) enterset Sink EF Faucets are furnished with a 1.5 gpm (3.8 Lpm) spray head). 1 - INSTLLTION TO DEK IMPORTNT: FLUSH DIRT, DERIS, ND SEDIMENT FROM SUPPLY LINE(S) EFORE ONNETING FLEx HOSE(S). Remove nut, faucet retainer and gasket. Install faucet into the center hole in deck or lavatory 1-3/16 (30 mm) minimum hole required. NOTE: If installing the faucet on a three (3) hole sink, a trim plate should be installed at this time. 2
2 - ONNETION TO WTER SUPPLY Flush supply stops before making connections. Install strainer and flex hose onto supply stop. D Tighten the flex hose (with strainer in place) securely to the supply. Open supply stop(s). 3 - EF-700 MODELS PLUG DPTER INTO REEPTLE ELETRIL ONNETION FOR UP TO SIx (6) FUETS USING ONE DPTER 6 VD PLUG-IN DPTER POWER SPLITTER ELETRIL LE POWER SPLITTER ELETRIL LE TO DDITIONL FUETS (6 Mx.) 3 - EF-750 MODELS ONNET TTERY PK TTERY PK Ø 2-13/32 (61 mm) LIMIT ONE FUET PER TTERY PK 3
4 - STRT-UP Remove label from faucet sensor. ctivate faucet by pressing the button one (1) time, then immediately step away. Faucet will run water for 4 seconds. Wait 10 seconds and then the faucet is ready to use. 3 7 SET ND FIX TEMPERTURE (OPTIONL) 4
HOT LIMIT STOP DJUSTMENT LIMIT THE MxIMUM WTER TEMPERTURE. NOTE: THIS DOES NOT TKE THE PLE OF N SSE 1070 ERTIFIED MIxING DEVIE. UT IS N DDED MESURE TO LIMIT DELIVERY OF HOT WTER. D E 5
SENSOR RNGE DJUSTMENT FTORY SETTING IS PPROPRITE FOR THE MJORITY OF PPLITIONS ND SHOULD NOT REqUIRE RESETTING UNLESS UNDER ExTREME SITUTIONS. D 8x 7x 2x + 5 Sec. 2x FTORY DEFULT = 6 4x E 5 Sec. (, 2x,...,5x) F G 6
12/24 LINE PURGE FETURE 24 sec h This feature will operate the faucet every 12 or 24 hours since last use, if not used to prevent stagnant water conditions. Default purge duration is two minutes. DETIVTE TIVTE 2x --- 12h onsult factory regarding other timing options. 3x 24h I.Q.-LIK FETURE I. ONTINUOUS RUN ontinuous run of water for 2 minutes. 2 Sec. 2 Sec. 2 Sec. 2 min. OR Faucet will operate normally after 2 minutes or after pressing i.q.-click button once. OR OR min. 2 min. II. LENING MODE Pause faucet for cleaning for 2 minutes. 2 x 2 x Faucet will operate normally after 2 minutes or after pressing i.q.-click button once. OR OR 2 min. 2 min. 6 Sec. 6 Sec. OFF-DELY (FOLLOW UP TIME) DURTION OF TIME THE WTER RUNS FTER TRGET IS REMOVED. Press the button for approximately six (6) seconds. Release. 0-5 Sec. 0-5 Sec. Sensor will flash once and then the faucet is ready to operate. 6 Sec. Press again (water flows) and release when the desired time of water flow (0-5 seconds) is reached. 0-5 Sec. 7
OPERTION s the user s hands enter the beam s effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing water to flow from the faucet. Water will flow until the hands of the user are removed or until the faucet reaches its automatic time out limit setting. TTERY REPLEMENT NOTE: REPLE TTERY WHEN RED LED INDITOR FLSHES EH TIME FUET IS IN USE OR WHEN FUET STOPS FUNTIONING. No need to turn off water. Loosen screw with hex wrench and remove cap. Slide cover forward and lift off. E ctivate faucet by pressing i.q. cliq one (1) time, then immediately step away. 0 V 6 V 0 V 6 V Remove battery. Replace batteries with new R-P2 lithium battery. F Faucet will operate for 4 seconds. 0 V 6 V 0 V 6 V D Replace cover. G Wait 10 seconds and then the faucet is ready for operation. x 6 V 8
TEHNIL DT NOMINL VOLTGE POWER SUPPLY WTER PRESSURE FLOW RTE WTER FLOW DURTION WTER TEMPERTURE TROULESHOOTING 6 VD 120 V/ 6.75 VD 4.3-125 PSI (0.3-8.6 bar) 1.5 gpm (5.7 Lpm) 0.5-4 seconds Mx. 176 F/80 1. Faucet does not function.. dhesive packaging label affixed over sensor eye. Remove adhesive label from sensor eye.. Intermittent Off is activated. Press button once.. Water supply stop(s) closed. Open water supply stop(s). D. attery is dead. Replace battery (refer to attery Replacement section of guide). 2. Faucet delivers water in an uncontrolled manner.. Reflection. Remove reflective surface.. Faucet is not working properly. ontact Sloan Valve ompany Installation Engineering Department. 3. Faucet does not deliver any water when Sensor is activated. Solenoid Valve produces an audible LIK.. Water supply stop(s) closed. Open water supply stop(s).. Water supply stop strainer(s) clogged. Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s), if required. Solenoid Valve DOES NOT produce an audible LIK.. attery low (battery operated models). Replace battery (refer to attery Replacement section of guide).. Power failure. heck power supply. 4. Faucet delivers only a slow flow or dribble when sensor is activated.. Water supply stop(s) are partially closed. ompletely open water supply stop(s).. Water supply stop strainer(s) clogged. Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s), if required.. Spray head is clogged. Remove, clean, and reinstall spray head. Replace spray head, if required. D. Faucet is not working properly. ontact Sloan Valve ompany Installation Engineering Department. 5. Faucet does not stop delivering water or contrinues to drip after user is no longer detected.. Faucet is not working properly. ontact Sloan Valve ompany Installation Engineering Department. 6. LED indicator blinks when faucet is in use.. attery low (battery operated models). Replace battery (refer to attery Replacement section of guide). 7. The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines.. Supply stops are not adjusted properly. djust supply stops. When assistance is required, please contact Sloan s Installation Engineering Department at: 1-888-SLON-14 (1-888-756-2614) RE ND LENING DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean faucets that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom sink, protect the faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating. 9
PRTS LIST 1 2 3 Item Part No. No. Description 1 Spout ssembly 2 Integral Side Mixer Handle ap 3 Integral Side Mixer Kit 4 EF-2 Solenoid 5 Sensor ssembly 6 EF-1 Mounting Hardware 7 EF-44 Power Splitter 8 EF-24-11-13/16 (300 mm) Extension able EF-25-47-1/4 (1200 mm) Extension able EF-17-126 (3200 mm) Extension able 9 EF-1008 13 (330 mm) Flexible Supply Hose 10 EF-9 Filter/Strainer 11 EF-48 attery ox 12 EF-11- Plug-in Voltage dapter, US Plug 5 4 6 7 8 9 10 11 12 The information contained in this document is subject to change without notice. SLON VLVE OMPNY 10500 SEYMOUR VENUE FRNKLIN PRK, IL 60133 Phone: 1-800-9-VLVE-9 (1-800-982-5839) Fax: 1-800-447-8329 www.sloanvalve.com opyright 2011 SLON VLVE OMPNY ode No.: 0816409 Rev. 1 (07/11)