IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction. The most updated information on this Certificate of Listing is available online at pld.iapmo.org Effective Date: May 2018 -Rev. 6/18/2018- Void After: May 2019 3700 Regency Parkway Suite 100 Cary, NC 27518 Identification: Each fitting shall bear permanent legible markings to identify the manufacturer. This marking shall be the trade name, trademark, or other mark known to identify the manufacturer. The product shall also bear all other markings required by the standard. The marking shall be located where it can be readily seen after installation is complete. The product shall also bear the cupc certification mark. Models in compliance with ICC/ANSI A117.1 shall be marked with "Also listed to ICC/ANSI A117.1" above the cupc certification mark. Characteristics: Plumbing fittings are to be installed in accordance with the manufacturer's instructions and the requirements of the latest edition of the Uniform Plumbing Code. Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025. This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
Products are in compliance with the following code(s): Uniform Plumbing Code (UPC ) National Plumbing Code of Canada International Plumbing Code (IPC ) Products are in compliance with the following standard(s): ASME A112.18.1-2012/CSA B125.1-12
MODELS: Models designated by "*" also comply with ICC/ANSI A117.1 TPK7300-SS Standard valve w/trim and service stops TPK7300-SSC Standard valve w/trim w/copper sweat fittings and service stops TPK7320-SS Standard valve w/trim and screw on diverter and service stops TPK7320-SSC Standard valve w/trim, screw on diverter, copper sweat fittings & service stops Z7300-SS Standard valve w/trim Z7300-SSC Standard valve w/trim w/copper sweat fittings Z7320-SS Standard valve w/trim and screw on diverter Z7320-SSC Standard valve w/trim, screw on diverter and copper sweat fittings *Z744X-YYY Sierra lavatory faucet w/flexible supply hose *Z744X-CST-YYY Sierra lavatory faucet w/copper supply tubes Suffixes: *X = Waste Options (0=None, 1=LR, 2=MP and 3=GS) *1st Y = Handle Type (LP) *2nd Y = Aerator Type (FC, LA and VP) *3rd Y = Finish Options (STN) *FC = 0.5 GPM Aerator *GS = Grid Strainer *LA = Laminar Flow Aerator, 2.2 GPM *LP = Loop Handle *LR = Lift Rod *MP = Metal Pop-up *STN = Satin Nickel Finish *VP = Vandal-Resistant Aerator, 2.0 GPM *Z82200-## Single Control Lavatory Faucet Z-811XY Lavatory Faucet Z-827XY Lavatory Faucet Z-812XY Lavatory Faucet Z-871XY Kitchen Faucet Z-841XY Service Sink Body Z-842XY Service Sink Faucet Z-843XY-Z Service Sink Faucet Z-1996-SF Service Sink Body Z-866A0 Metering Z-867XY Metering Z-80300 Metering Z-86100 Metering Z-86300 Metering Page 3 of 17
Z-86300-7M Metering Z-86500 Metering Z-86500-P Metering Z-825XY Laboratory Z-826XY Laboratory Z-821XY Health care/medical gooseneck spout Z-851XY Health care/medical faucet Z-851XY-WM Health care/medical faucet Z-85500 Health care/medical faucet Z-85500-LM Health care/medical faucet Z-85500-WM Health care/medical faucet Z-85700 Health care/medical faucet "X" in the model denotes Spout Type (A,B,C,F,G,H,I,J,K,L,M,N,Q,R,S,T,U) "Y" in the model denotes Handle Type (1,2,3,4,6) "Z" in the model denotes various options (140, 11F, 11M, 14F 14M, 16F, 16M, 17F, 17M, 18F, 18M, 1F, 1M, 2F, 2M, 3F, 3M, 4F, 4M, 7F, 7M, G, GH, WHK) ## Indicates the unit furnished with the following: 1M 2.2 GPM max aerator 2M 2.0 GPM aerator 3M 0.5 GPM aerator 4M 2.2 GPM max. laminar flow aerator 11M Less aerator 14M 2.2 GPM max. laminar flow aerator CP4 4" chrome plated zinc cover plate CP8 8" chrome plated zinc cover plate 18FH 18" S.S. braided flexible connectors * Z824XY-Z Single-Handle kitchen faucet with swing spout *Z-86000 4" Centerset Metering Mixing Faucet *Z-86000-3M 0.5 GPM Vandal-Resistant Pressure Compensating Male Spray Outlet *Z-86000-16M 1.0 GPM Vandal-Resistant Pressure Compensating Male Spray Outlet X can be replaced with 0, A, B, C, S, Y indicating the spout style Y can be replaced with 0 indicating the handle style Z can be replaced with 0, 1F, 2F, 3F, 4F, 7F, 16F, 17F, 18F, 18FH with the following options: 0-2.2 gpm standard aerator 1F-0.5 gpm spray type flow restrictor 2F-2.2 gpm aerated type junior flow restrictor 3F-0.5 gpm spray type junior flow restrictor 4F-2.2 gpm laminar type flow restrictor Page 4 of 17
7F-1.0 gpm spray type junior flow restrictor 16F-1.0 gpm spray type junior flow restrictor 17F-1.5 gpm aerated type junior flow restrictor 18F-1.5 gpm laminar type junior flow restrictor 18FH-18" gpm flexible inlet hose Z81200-XL 4 Centerset Lavatory Faucet Suffix -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -G 1-1/4 [32mm] Grid Strainer Drain -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Aerator -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow -7F 1.0 GPM [3.8 L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Laminar Flow -21F 1.0 GPM [3.8L] Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Vandal-Resistant Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator Z82100-XL Health Care/Medical Gooseneck Spout -WM Wall Mount Z82500-XL Laboratory Faucet Single Suffix -AR Anti-Rotation Pins -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -G 1-1/4" [32mm] Grid Strainer Drain -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8 L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Laminar Flow Page 5 of 17
-21F 1.0 GPM [3.8L] Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Vandal-Resistant Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator Z82600-XL Laboratory Faucet Suffix -AR Anti-Rotation Pins -CST Copper Supply Tubes -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -G 1-1/4" [32mm] Grid Strainer Drain -MY Mixing Yoke Assembly Instead of Copper Supplies -140 Restricted 140j Swing Spout -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator Z83100-XL Widespread Kitchen Faucet Suffix -CWO Cold Water Only -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -G 1-1/4" [32mm] Grid Strainer Drain -GH 1-1/4" [32mm] Offset Handicap Grid Drain -HS Hose and Spray -ICT Inter-connecting Copper Supply Tubes for 8 In-line Centers -P 1-1/4" [32mm] Pop-up Drain -PT 1-1/4 [32mm] Cast Brass P-Trap with a 7-1/2 [191mm] Long 17-Gauge Wall Bend -TW Third Waterway -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet Page 6 of 17
-17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -20F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Anti-Microbial Female Laminar Flow Outlet -21F 1.0 GPM [3.8L] Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Vandal-Resistant Female Laminar Flow Outlet Z84100-XL Wall Mounted Service Sink Faucet Suffix -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -SSI 3/8" [10mm] Short Swivel Inlets -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8L] Pressure Compensating Female Spray Outlet -15F Female Full Flow Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator -140 140o Restricted Swing Spout Z84200-XL Wall Mounted Service Sink Faucet Suffix -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -LSI 2-1/2" [64mm] Long Swivel Inlets with Integral Stops -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8 L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Laminar Flow -22F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator Page 7 of 17
Z84300-XL Wall Mounted Service Sink Faucet Suffix -CS Check Stops -LSI 2-1/2" [64mm] Long Swivel Inlets -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8 L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Z87100-XL Kitchen Faucet Suffix -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -HS Hose and Spray -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow -7F 1.0 GPM [3.8 L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Female Laminar Flow -22F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator -24F 0.35 GPM [1.3 L] Pressure Compensating Female Spray Outlet -25F 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Female Spray Outlet Z81000-XL 4 Centerset Single Control Lavatory Faucet Suffix -G 1-1/4 [32mm] Grid Strainer Drain -P 1-1/4 [32mm] Pop-up Drain -PT 1-1/4 [32mm] Cast Brass P-Trap with a 7-1/2 [191mm] Long 17-Gauge Wall Bend -1M 2.2 GPM [8.3 L] Variable-Pressure Compensating Male Aerator Page 8 of 17
-2M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Aerator -3M 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Aerator -4M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Laminar Flow -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -17M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Male Aerator -18M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Laminar Flow -19M 1.5 GPM [5.7 L] Anti-Microbial Pressure Compensating Male Laminar Flow Outlet -21M 1.0 GPM [3.8L] Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Vandal-Resistant Male Laminar Flow Outlet -23M 1.5 GPM [5.7L] Pressure Compensating Male Aerator -24M 0.35 GPM [1.3 L] Pressure Compensating Male Spray Outlet -25M 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Male Spray Outlet Z82200-XL Single Control Lavatory Faucet Suffix -CP8 Chrome Plated 8 [203mm] Cover Plate -CST Copper Supply Tubes -G 1-1/4 [32mm] Grid Strainer Drain -P 1-1/4 [32mm] Pop-up Drain -2M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Aerator -3M.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -4M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Laminar Flow Outlet -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Male Spray Outlet -17M 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Male Aerator -18FH 18 [457mm] S.S. Braided Flex Hoses -18M 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Male Laminar Flow -19M 1.5 GPM [5.7 L] Anti-Microbial Pressure Compensating Male Laminar Flow Outlet -21M 1.0 GPM [3.8L] Pressure Compensating Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Male Laminar Flow Outlet -23M 1.5 GPM [5.7L] Pressure Compensating Male Aerator Z82300-XL Single Control Kitchen Faucet Suffix -CP4 Chrome Plated 4 [102mm] Cover Plate -CP8 Chrome Plated 8 [203mm] Cover Plate -CST Copper Supply Tubes -G 1-1/4 [32mm] Grid Strainer Drain -HS Hose and Spray -2M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Aerator -3M 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -4M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Laminar Flow Outlet -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet Page 9 of 17
-16M 1.0 GPM [3.8 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -17M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Male Aerator -18FH 18 [457mm] S.S. Braided Flex Hoses -18M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Male Laminar Flow -19M 1.5 GPM [5.7 L] Anti-Microbial Pressure Compensating Male Laminar Flow Outlet -21M 1.0 GPM [3.8L] Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Vandal-Resistant Male Laminar Flow Outlet -23M 1.5 GPM [5.7L] Pressure Compensating Male Aerator Z82400-XL Single Control Kitchen Faucet Suffix -CST Copper Supply Tubes -FC 2.0 GPM [7.6L] Laminar Flow Control in Base of Spout -HS Hose and Spray -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8L] Pressure Compensating Female Spray Outlet -15F Female Full Flow Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -18FH 18 [457mm] S.S. Braided Flex Hose -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator -140 140o Restricted Swing Gooseneck Spout Z81100-XL 4 Centerset Dual Handle Control Lavatory Faucet -G 1-1/4" [32mm] Grid Strainer Drain -2M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Aerator -3M 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Aerator -4M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Laminar Flow -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -17M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Male Aerator -18M 1.5 GPM [5.7 L] Vandal-Resistant Pressure Compensating Male Laminar Flow -22F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -23F 1.5 GPM [5.7L] Pressure Compensating Female Aerator Page 10 of 17
-24M 0.35 GPM [1.3 L] Pressure Compensating Male Spray Outlet -25M 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Male Spray Outlet Z82700-XL Single Lavatory Faucet - CP4 Chrome-Plated 4 [102mm] Cover Plate -G 1-1/4" [32mm] Grid Strainer Drain -2M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Aerator -3M.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -4M 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Male Laminar Flow Outlet -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Male Spray Outlet -17M 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Male Aerator -18M 1.5 GPM [5.7 L] Vandal Resistant Pressure Compensating Male Laminar Flow -19M 1.5 GPM [5.7 L] Anti-Microbial Pressure Compensating Male Laminar Flow Outlet -21M 1.0 GPM [3.8L] Pressure Compensating Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Male Laminar Flow Outlet -23M 1.5 GPM [5.7L] Pressure Compensating Male Aerator Z82600-XL Laboratory Faucet Suffix -AR Anti-Rotation Pins -CST Copper Supply Tubes -FC 2.0 GPM [7.6 L] Laminar Flow Control in Base of Spout -G 1-1/4" [32mm] Grid Strainer Drain -MY Mixing Yoke Assembly Instead of Copper Supplies -140 Restricted 140j Swing Spout -2F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Aerator -3F 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -4F 2.2 GPM [8.3 L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -7F 1.0 GPM [3.8L] Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8L] Vandal-Resistant Pressure Compensating Female Spray Outlet -17F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Aerator -18F 1.5 GPM [5.7L] Vandal-Resistant Pressure Compensating Female Laminar Flow Outlet -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet Z86100-XL Single Basin Metering Faucet Page 11 of 17
Suffix -CS Check Stop -CP4 Chrome-Plated 4 [102mm] Cover Plate -G 1-1/4" [32mm] Grid Strainer Drain -GH 1-1/4" [32mm] Offset Handicap Drain -IN Institutional Handle- Tamper-Proof and Vandal-Resistant -RKR ADA Compliant Rocker Handle -3M 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -7M 1.0 GPM [3.8 L] Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -21M 1.0 GPM [3.8L] Pressure Compensating Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Male Laminar Flow Outlet -24M 0.35 GPM [1.3 L] Pressure Compensating Male Spray Outlet -25M 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Male Spray Outlet Z86300-XL Single Basin Metering Faucet -CS Check Stops -G 1-1/4 [32mm] Grid Strainer Drain -GH 1-1/4 [32mm] Offset Handicap Grid Drain -IN Institutional Handle - Tamper-Proof and Vandal-Resistant -MY Mixing Yoke -MYCS Mixing Yoke with Check Stops -3M 0.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -21M 1.0 GPM [3.8L] Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Vandal-Resistant Male Laminar Flow Outlet -24M 0.35 GPM [1.3 L] Pressure Compensating Male Spray Outlet -25M 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Male Spray Outlet Z86500-XL 4 Centerset Metering Faucet Suffix -G 1-1/4" [32mm] Grid Strainer Drain -GH 1-1/4" [32mm] Offset Handicap Drain -IN Institutional Handle- Tamper-Proof and Vandal-Resistant -RKR ADA Compliant Rocker Handle -3M.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Male Spray Outlet -16M 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Male Spray Outlet -21M 1.0 GPM [3.8L] Pressure Compensating Male Laminar Flow Outlet -22M 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Male Laminar Flow Outlet -24M 0.35 GPM [1.3 L] Pressure Compensating Male Spray Outlet -25M 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Male Spray Outlet Page 12 of 17
Z86600-XL 4 Centerset Metering Faucet Suffix -G 1-1/4 [32mm] Grid Strainer Drain -GH 1-1/4 [32mm] Offset Handicap Grid Drain -IN Institutional Handle - Tamper-Proof and Vandal-Resistant -P 1-1/4 [32mm] Pop-up Drain -RKR ADA Compliant Rocker Handle -140 140 Restricted Swing Spout -3F.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet -24F 0.35 GPM [1.3 L] Pressure Compensating Female Spray Outlet -25F 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Female Spray Outlet Z86700-XL Widespread metering faucet Suffix -CWO Cold Water Only -G 1-1/4" [32mm] Grid Strainer Drain -GH 1-1/4" [32mm] Offset Handicap Drain -ICT Inter-connecting Copper Supply Tubes for 8 In-line Centers -IN Institutional Handle - Tamper-Proof and Vandal-Resistant -P 1-1/4" [32mm] Pop-up Drain -RKR ADA Compliant Rocker Handle -140 140o Restricted Swing Spout -3F.5 GPM [1.9 L] Vandal-Resistant Pressure Compensating Female Spray Outlet -16F 1.0 GPM [3.8 L] Vandal Resistant Pressure Compensating Female Spray Outlet -22F 1.0 GPM [3.8L] Pressure Compensating Vandal-Resistant Female Laminar Flow Outlet -24F 0.35 GPM [1.3 L] Pressure Compensating Female Spray Outlet -25F 0.35 GPM [1.3 L] Vandal-Resistant Pressure Compensating Female Spray Outlet Z80300-XL Wall Mounted Single Metering Faucet -IN -RKR Institutional Handle Rocker Handle AquaSense Electronic Sensor Faucets Page 13 of 17
Z6913-XL-z Z6915-XL-z Z6920-XL-x-z Z6920XT-XL-x-z Z6923-XL-x-z Z6922-XL-x-z Z6922XT-XL-x-z Z6930-XL-z Z6950-XL-IM-S-z Z6950-XL-S-z Z6951-XL-z Z6952-XL-z Z6953-XL-z Z6954-XL-z Z6955-XL-S-z Z6956-XL-z Z6957-XL-z Deck Mount Sensor-operated Faucet (Three Hole) Deck Mount Sensor-operated Faucet Deck Mount Goose Neck Sensor-operated Faucet Deck Mount Goose Neck Sensor-operated Faucet (Extended Range Sensor) Deck Mount Goose Neck Sensor-operated Faucet Wall Mount Goose Neck Sensor-operated Faucet Wall Mount Goose Neck Sensor-operated Faucet (Extended Range Sensor) Deck Mount Sensor operated Faucet Deck Mount Sensor-operated Faucet with Integral Mixing Valve Deck Mount Sensor-operated Faucet Sensor-operated Lav Faucet Wall Mount Sensor- operated Faucet Deck Mount Sensor-operated Faucet Deck Mount Sensor-operated Faucet Deck Mount Sensor-operated Faucet (Three Hole) Deck Mount Sensor-operated Faucet NACHI Wall-Mounted Sensor Lavatory Faucet x = spout options (0, GA, GA-FC, GB, GB-FC, GC, GC-FC, GC-10, GC-10-FC) -GA -GA-FC -GB -GB-FC -GC -GC-FC -GC-10 -GC-10-FC G67851 3-1/2" centerline gooseneck spout G67856 3-1/2" centerline gooseneck spout with Flow Control G67852 5-3/8" centerline gooseneck spout G67857 5-3/8" centerline gooseneck spout with Flow Control G67853 8" centerline gooseneck spout G67858 8" centerline gooseneck spout with Flow Control G67854 10" centerline gooseneck spout G67859 10" centerline gooseneck spout with Flow Control z= miscellaneous options (ACA, ADM, CP4, CP8, CWB, E, F, GEN, HW6, J, K, L, M, MJ, MV, N, SH, SSH, TMV-1, XT) -ACA -ADM -BN -CP4 -CP8 -CWB -GEN -HW6 -MJ -MT -MV -TMV-1 -SH P6900-ACA, P6957-ACA, 6 VDC A/C Plug-In Adapter P6900-ADM-XL, Above-Deck Mixer Brushed Nickel P6900-CP4, 4" Cover plate P6900-CP8, 8" Cover plate P6900-CWB, connecting wire for power converter P6900-GEN-XL, hydro generator power P6000-HW6, hardwired power converter P6000-MJ, mini junction box P6900-MT-XL, mixing tee P6900-MV-XL, manual mixing valve P6900-TMV-1, thermostatic mixing valve for single faucet P6900-SH, three piece supply hose assembly Page 14 of 17
-SSH P6900-SSH, single supply hose -FC2.0 2.0 GPM Flow Control (93446001) -FC1.5 1.5 GPM Flow Control (93445001) -FC1.0 1.0 GPM Flow Control (93444001) -FC0.74 0.74 GPM Flow Control (200455001) -FC0.5 0.5 GPM Flow Control (93443001) -20E-GN-CG 1.5 GPM spray outlet, with Careguard, female (200080001) -20E-CG 1.5 GPM spray outlet, with Careguard, male (200082001) -PN Polished Nickel -PB Polished Brass -XT Extended Range Sensor -z miscellaneous options (ACA, ADM, CP4, CP8, CWB, E, F, GEN, HW6, J, K, L, M, MJ, MV, N, SH, SSH, TMV-1, XT) Aerators P6900-20E -E, 1.5 GPM spray outlet, male (310505001) P6900-20ES -ES, 1.5 GPM slim spray outlet, male (310584001) P6900-20E-GN -E, 1.5 GPM spray outlet, female (G66695) P6900-20F -F, 0.5 GPM vandal resistant spray outlet, male (310505005) P6900-20FS -FS, 0.5 GPM slim spray outlet, male (310584005) P6900-20F-GN -F, 0.5 GPM vandal resistant spray outlet, female (60440001) P6900-20J -J, 1.5 GPM vandal resistant laminar flow, male (310505002) P6900-20JS -JS, 1.5 GPM slim laminar flow, male (310584002) P6900-20J-GN -J, 1.5 GPM vandal resistant laminar flow, female (81052001) P6900-20K -K, 1.0 GPM laminar flow, male (310505004) P6900-20K-GN -K, 1.0 GPM laminar flow, female (81882001) P6900-20L -L, 1.0 GPM spray outlet, male (310505003) P6900-20LS -LS, 1.5 GPM slim laminar flow, male (310584003) P6900-20L-GN -L, 1.0 GPM spray outlet, female (81883001) P6900-20M -M, 0.35 GPM spray outlet, male (310505006) P6900-20MS -MS, 0.35 GPM slim spray outlet, male (310584006) P6900-20M-GN -M, 0.35 GPM spray outlet, female (309103001) P6900-20N -N, 0.5 GPM laminar flow, male (200456001) P6930-20E -E, 1.5 GPM vandal resistant hidden spray outlet, male (310233001) P6930-20F -F, 0.5 GPM vandal resistant hidden spray outlet, male (310233005) P6930-20J -J, 1.5 GPM vandal resistant hidden laminar flow, male (310233002) P6930-20K -K, 1.0 GPM vandal resistant hidden laminar flow, male (310233004) P6930-20L -L, 1.0 GPM vandal resistant hidden spray outlet, male (310233003) P6930-20M -M, 0.35 GPM vandal resistant hidden spray outlet, male (310233006) P6930-20N -N, 0.5 GPM vandal resistant hidden laminar flow, male (200457001) 81881001 E, 1.5 gpm spray outlet, female 60440001 F, 0.5 gpm vandal resistant spray outlet, female Page 15 of 17
81052001 J, 1.5 gpm vandal resistant laminar flow, female 81882001 K, 1.0 gpm laminar flow, female 81883001 L, 1.0 gpm spray outlet, female 309103001 M, 0.35 gpm spray outlet, female 93446001 2.0 gpm Flow Control 93445001 1.5 gpm Flow Control 93444001 1.0 gpm Flow Control 200455001 0.74 gpm Flow Control 93443001 0.5 gpm Flow Control 1. "X" in the model number denotes spout type (A, B, C, DE F, G H, H, I, J, K, L, M, N, Q, R, S, T, U). 2. "Y" In the model number denotes Handle Type (1, 2, 3, 4, 6) 3. Additional suffix may be added to denote accessories Supply Stops Only Z81006-XL Qtr Turn Stop (1/2" COMP x 1/2" NPT) (Lead Free) Z81017-XL Qtr Turn Stop (3/8" COMP x 1/2" NPT) (Lead Free) Z81005-XL Qtr Turn Stop (1/2" COMP x 3/8" NPT) (Lead Free) Z81016-XL Qtr Turn Stop (3/8" COMP x 3/8" NPT) (Lead Free) Stop & Flex Hose Z81005-XL-LR-8862-12-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 12" SS Hose Z81005-XL-LR-8862-16-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 16" SS Hose Z81005-XL-LR-8862-20-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 20" SS Hose Z81005-XL-LR-8862-30-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 30" SS Hose *Z81005-XL-LR-8862-36-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 36" SS Hose Z81006-XL-LR-8862-12-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 12" SS Hose Z81006-XL-LR-8862-16-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 16" SS Hose Z81006-XL-LR-8862-20-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 20" SS Hose Z81006-XL-LR-8862-30-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 30" SS Hose *Z81006-XL-LR-8862-36-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 36" SS Hose Z81016-XL-LR-8860-12-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 12" SS Hose Z81016-XL-LR-8860-16-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 16" SS Hose Z81016-XL-LR-8860-20-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 20" SS Hose Z81016-XL-LR-8860-30-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 30" SS Hose *Z81016-XL-LR-8860-36-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 36" SS Hose Z81016-XL-LR-8863-12-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 12" SS Hose Z81016-XL-LR-8863-16-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 16" SS Hose Z81016-XL-LR-8863-20-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 20" SS Hose Z81016-XL-LR-8863-30-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 30" SS Hose *Z81016-XL-LR-8863-36-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 36" SS Hose Z81017-XL-LR-8860-12-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 12" SS Hose Z81017-XL-LR-8860-16-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 16" SS Hose Z81017-XL-LR-8860-20-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 20" SS Hose Page 16 of 17
Z81017-XL-LR-8860-30-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 30" SS Hose *Z81017-XL-LR-8860-36-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 36" SS Hose Z81017-XL-LR-8863-12-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 12" SS Hose Z81017-XL-LR-8863-16-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 16" SS Hose Z81017-XL-LR-8863-20-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 20" SS Hose Z81017-XL-LR-8863-30-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 30" SS Hose *Z81017-XL-LR-8863-36-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 36" SS Hose Stop & Lavatory Riser Tube Z81005-XL-LR-8973-12-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 12" Riser Tube Z81005-XL-LR-8973-20-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 20" Riser Tube Z81006-XL-LR-8973-12-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 12" Riser Tube Z81006-XL-LR-8973-20-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 20" Riser Tube Z81016-XL-LR-8972-12-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 12" Riser Tube Z81016-XL-LR-8972-15-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 15" Riser Tube Z81016-XL-LR-8972-20-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 20" Riser Tube Z81016-XL-LR-8972-30-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 30" Riser Tube *Z81016-XL-LR-8972-36-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 36" Riser Tube Z81017-XL-LR-8972-12-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 12" Riser Tube Z81017-XL-LR-8972-15-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 15" Riser Tube Z81017-XL-LR-8972-20-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 20" Riser Tube Z81017-XL-LR-8972-30-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 30" Riser Tube *Z81017-XL-LR-8972-36-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 36" Riser Tube Stop & Closet Riser Tube Z81005-XL-CR-8975-12-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 12" Riser Tube Z81005-XL-CR-8975-15-PC Qtr Turn Stop (1/2" COMP X 3/8" NPT) w/ 15" Riser Tube Z81006-XL-CR-8975-12-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 12" Riser Tube Z81006-XL-CR-8975-15-PC Qtr Turn Stop (1/2" COMP X 1/2" NPT) w/ 15" Riser Tube Z81016-XL-CR-8974-12-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 12" Riser Tube Z81016-XL-CR-8974-15-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 15" Riser Tube Z81016-XL-CR-8974-20-PC Qtr Turn Stop (3/8" COMP X 3/8" NPT) w/ 20" Riser Tube Z81017-XL-CR-8974-12-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 12" Riser Tube Z81017-XL-CR-8974-15-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 15" Riser Tube Z81017-XL-CR-8974-20-PC Qtr Turn Stop (3/8" COMP X 1/2" NPT) w/ 20" Riser Tube Note: Models with an * shall bear the UPC mark. Page 17 of 17