VICTORIAN AND S INSTALLATION DETAILS MANUACTURING 800-669-0009 www.berridge.com
INDEX INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INTRODUCTION TO TYPICAL DETAILS OVERVIEW VICTORIAN SHINGLE OVERVIEW VC-0 VCI-1 VCI-2 VCI-3 VC-2 VS-5 CS-5 EAVE DETAIL VC-10 RIDGE AND HIP DETAIL SHED ROO RIDGE CAP DETAIL RIDGE TERMINATION AT DORMER VALLEY GABLE DETAIL VC-20 VC-21 VC-22 VC-30 PARAPET DETAIL HEAD WALL DETAIL HEAD WALL DETAIL RAKE WALL DETAIL RAKE WALL DETAIL SLOPE TRANSITION DETAIL VC-40 VC-41 VC-42 VC-50 VC-51 VC-60 VALLEY DETAIL VC-70 PIPE PENTRATION 4" DIA. OR LESS ROO PENETRATION RECTANGULAR/SQUARE ROO PENETRATION SECTION DETAIL ROO PENETRATION SECTION DETAIL ROO PENETRATION SECTION DETAIL VC-80 VC-81 VC-82 VC-83 VC-84 MANUACTURING INDEX PAGE/ILE VC-0
A. B. C. VICTORIAN AND S: VICTORIAN AND S HAVE AN EXPOSURE O 9" X 12" MINIMUM SLOPE: THE VICTORIAN AND S ARE RECOMMENDED OR SLOPES O 3:12 OR GREATER. MATERIAL STORAGE: CAUTION MUST BE EXERCISED IN STORAGE O MATERIALS PRIOR TO INSTALLATION. KEEP ALL PREINISHED MATERIAL IN A DRY LOCATION WITH ADEQUATE VENTILATION AND OUT O DIRECT SUNLIGHT. EXPOSURE TO DIRECT SUNLIGHT AND/OR MOISTURE MAY CAUSE THE ACTORY APPLIED STRIPPABLE PLASTIC ILM TO ADHERE TO THE METAL PERMANENTLY AND DISCOLOR THE INISH. D. E.. G. H. STRIPPABLE ILM: THE STRIPPABLE PLASTIC ILM WHICH IS APPLIED OVER MOST PREINISHED PRODUCTS, PANELS, LASHINGS, COILS AND LAT SHEETS PROTECTS THE INISH DURING ABRICATION AND TRANSIT. THIS ILM MUST BE REMOVED PRIOR TO INSTALLATION. REQUIREMENTS: MANUACTURING RECOMMENDS THE USES O A MINIMUM O SOLID WOOD SHEATHING TO PROVIDE SUICIENT HOLDING POWER OR ASTENERS. CONTACT MANUACTURING'S ENGINEERING DEPARTMENT OR USE O ANY OTHER TYPE O. SHEATHING INSPECTION: 1. SHEATHING END JOINTS SHOULD BE STAGGERED. 2. ALL END JOINTS SHOULD MEET AT EITHER A JOIST OR RATER. 3. BLOCKING OR "H" CLIPS SHOULD BE USED ON PLYWOOD O JOINTS DO NOT REMAIN LAT UNDER THE WEIGHT O WORKMEN. 4. USE SHIMS TO KEEP ENTIRE SUBSTRATE EVEN. SUBSTRATE SHOULD BE LEVEL TO IN 20'-0". 5. ALL CUTS AT PENETRATIONS SHOULD BE TIGHT, WITHOUT GAPS. 6. USE WOOD RAMED CRICKETS AT LARGE PENETRATIONS. 7. MAKE SURE SUBSTRATE JOINTS ARE TIGHT AT ALL HIPS, VALLEYS AND RIDGES. ASCIA/RAKE INSPECTION: 1. STRIKE A LINE THE ULL LENGTH O THE ASCIA OR RAKE. I NOT STRAIGHT, CORRECT WITH SHIMS. 2. MAKE SURE ASCIA/RAKE IS LUSH WITH ROO SUBSTRATE SHEATHING. ELT UNDERLAYMENT: A SINGLE LAYER O NUMBER THIRTY ELT UNDERLAYMENT (OR EQUAL) MUST BE APPLIED OVER AS SHOWN IN THE MANUACTURING TYPICAL ELTING DETAILS. THE USE O ADDITIONAL LAYERS O NUMBER THIRTY ELT IS RECOMMENDED ON LOW-SLOPED ROOS, AT ALL VALLEY CONDITIONS, AT ROO PENETRATIONS, AND CERTAIN OTHER LASHING CONDITIONS AS DEPICTED IN THE VICTORIAN AND CLASSIC TYPICAL DETAILS. GRACE ICE AND WATER SHIELD MAYBE REQUIRED ON LOW SLOPED ROOS OR AT CERTAIN LASHING CONDITIONS. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE VCI-1
I. J. K. L. N. ELTING INSTALLATION: 1. DO NOT USE RED ROSIN PAPER UNDER METAL ROOING PANELS. 2. SWEEP ROO AREA CLEAN. 3. USE LAT HEAD GALVANIZED ROOING NAILS X 1- LONG WITH GALVANIZED ELT CAPS. 4. INSTALL VALLEY ELT IRST 5. INSTALL ELT PARALLEL TO EAVE (2 LAYERS REQUIRED AT EAVE), STARTING AT EAVE AND USING MINIMUM 6" LAPS. USE TWO LAYERS O ELT ON ENTIRE ROO DECK I SLOPE IS 3:12. 2 LAYERS REQUIRED AT EAVE REGARDLESS O SLOPE. 6. INSULATE BETWEEN WOOD BLOCKING AND METAL WITH ELT OR ICE AND WATER SHIELD. ELECTROLYSIS: AVOID ALLOWING LASHING AND PANELS TO COME INTO CONTACT WITH EITHER LEAD OR COPPER, AND PREVENT EXPOSURE TO WATER RUNDOWN ROM COPPER AND/OR LEAD. LASHING: I MANUACTURING IS TO SUPPLY LASHING, ALL LASHINGS WILL BE ABRICATED IN 10'-0" LENGTHS WITH SQUARE END CUTS ONLY. THE PURCHASER MUST PROVIDE ALL DIMENSIONS AND DEGREE O ANGLES. LASHING INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM EACH SHINGLE PRIOR TO INSTALLATION. 2. START AT LOWER LET EAVE CORNER AND STAGGER AS SHOWN ON DETAIL VS-5 AND CS-5. 3. USE CHALK LINES TO KEEP SHINGLES STRAIGHT. 4. SHINGLES INTERLOCK AT SIDE LAP AND OVERLAP ROM COURSE TO COURSE. 5. WHEN SHINGLES REACH THE VALLEY OR HIP TRIM THE SHINGLES SO THAT THEY IT TIGHT INTO S. 6. TRIM SHINGLES AS NECESSARY AT THE RIDGE SO THAT THE BOTTOM EDGE O THE SHINGLE OLLOWS THE PATTERN O THE OTHER SHINGLES AND THE TOP O THE SHINGLE ITS TIGHT IN THE. ASTENERS: NAIL SHINGLES THROUGH LOCK SEAM WITH A MINIMUM O (2) 1- GALVANIZED ROOING NAILS. MAKE SURE ALL ASTENERS ARE DRIVEN STRAIGHT AND SET LAT. DO NOT OVERDRIVE ASTENERS, AS THIS WILL CAUSE BUCKLING O SHINGLES. O. SEALANT RECOMMENDATIONS: TREMCO INC. SPECTREM 1 OR EQUAL. DO NOT USE CLEAR CAULK **CONSULT MANUACTURING'S ENGINEERING DEPARTMENT REGARDING THE USE O ANY OTHER TYPE O ASTENER. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE VCI-2
MANUACTURING STRIVES TO PROVIDE ITS CUSTOMERS WITH THE HIGHEST QUALITY STRETCHER LEVELED STEEL AVAILABLE. THE LATEST TECHNOLOGY IS ALSO INCORPORATED IN 'S HIGH-PRECISION COIL HANDLING AND ROLL ORMING EQUIPMENT TO MINIMIZE THE STRESS ON METAL DURING PRODUCTION. URTHERMORE, UTILIZES HEAVIER 24 GAUGE METAL RATHER THAN 26 GAUGE STEEL OR LIGHT GAUGE ALUMINUM AS OERED BY MANY COMPETITORS. ALL THESE MEASURES HAVE BEEN TAKEN TO MINIMIZE THE AMOUNT O "OIL-CANNING" (WAVINESS) WHICH IS NATURALLY INHERENT IN LAT SHEET METAL MANY TIMES, HOWEVER, THE CAUSE O WAVINESS OR "OIL-CANNING" CAN BE TRACED TO UNEVEN SHEATHING, IMPROPER ELT INSTALLATION, IMPROPER HANDLING, OR OOT TRAIC ON THE PANELS. ALL ARCHITECTURAL PRODUCTS REQUIRE CARE IN HANDLING AND INSTALLATION TO AVOID DAMAGING OR DEORMING THE PANELS. THESE INSTALLATION INSTRUCTIONS AND THE OLLOWING TYPICAL DETAILS ARE INTENDED TO PROVIDE OUT CUSTOMERS WITH THE INORMATION REQUIRED OR AN AESTHETICALLY PLEASING AND UNCTIONAL INSTALLATION O THE VICTORIAN OR S. NOTE: ALL PRODUCTS, SPECIICATIONS, DETAILS, AND INSTRUCTIONS SUBJECT TO CHANGE WITHOUT NOTICE. OR SPECIIC PROJECT DETAILS, CONTACT MANUACTURING. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE BI-3
THE DETAILS CONTAINED IN THE OLLOWING PAGES ARE MERELY RECOMMENDATIONS AS TO HOW MANUACTURING MATERIALS SHOULD BE INSTALLED. THEY MAY REQUIRE ADAPTATIONS OR MODIICATIONS OR A SPECIIC PROJECT AS CONDITIONS VARY IN BOTH BUILDING DESIGN AND LOCAL WEATHER PECULIARITIES. MANUACTURING SHALL BE HELD HARMLESS ORM ANY AND ALL CLAIMS ARISING ROM LACK O WATERTIGHTNESS AS A RESULT O OLLOWING THESE RECOMMENDED DETAILS. ENSURING THE WATERTIGHTNESS ON ANY GIVEN PROJECT IS THE UNCTION O THE INSTALLER. THE ARCHITECT/GENERAL CONTRACTOR/INSTALLER MUST ACCEPT THE RESPONSIBILITY TO ADAPT THESE DETAILS TO MEET PARTICULAR BUILDING REQUIREMENTS AND TO ASSURE ADEQUATE WATERTIGHTNESS. THE INSTALLER CAN VIRTUALLY ASSURE WATERTIGHTNESS I THESE LASHING DETAILS HAVE BEEN PROPERLY ADAPTED, ADEQUATE LAPS HAVE BEEN PROVIDED, CORRECT TYPE O SEALANT USED, ALL JOINT ADEQUATELY CAULKED, AND PROESSIONAL WORKMANSHIP EMPLOYED. MANUACTURING INTRODUCTION TO TYPICAL DETAILS PAGE/ILE VC-2
MINIMUM 2 ASTENERS AT LOCK SEAM IELD CUT 1/2 SHINGLE TO CREATE STAGGERED PATTERN VICTORIAN SHINGLES VICTORIAN SHINGLE LOCK SEAM 12" EXPOSURE 9" EXPOSURE MANUACTURING OVERVIEW Victorian Victorian Classic Shingle Shingles PAGE/ILE VS-5
MINIMUM 2 ASTENERS AT LOCK SEAM IELD CUT 1/2 SHINGLE TO CREATE STAGGERED PATTERN S START AT EAVE, WORK ROM LET TO RIGHT 12" EXPOSURE LOCK SEAM 9" EXPOSURE MANUACTURING OVERVIEW Victorian Classic or Classic Shingle Shingles PAGE/ILE CS-5
VICTORIAN OR # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C. MAX. DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING EAVE DETAIL PAGE/ILE VC-10
RIDGE/HIP CAP; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 20" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS, 20" O.C. MAX. # 30 ELT UNDERLAYMENT 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELTING UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RIDGE/HIP CAP MANUACTURING RIDE AND HIP DETAIL PAGE/ILE VC-20
SHED RIDGE CAP; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO AT 20" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR # 30 ELT UNDERLAYMENT LAP ELT OVER RIDGE ASTENERS; 40" O.C. MAX. CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SHED RIDGE CAP MANUACTURING SHED ROO RIDGE CAP DETAIL PAGE/ILE VC-21
SECTION VIEW SECTION VIEW IELD ORM END O RIDGE LASHING AND EXTEND UNDER RIDGE LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ; DO NOT CAULK ON OR UNDER VICTORIAN OR VC-20 # 30 ELT UNDERLAYMENT VALLEY LASHING; 12" LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD PLAN VIEW MAIN ROO RIDGE LASHING CONTINUOUS VALLEY LASHING DORMER ROO MANUACTURING RIDGE TERMINATION AT DORMER VALLEY PAGE/ILE VC-22
VICTORIAN OR CONTINUOUS BEAD O CAULK TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING GABLE DETAIL PAGE/ILE VC-30
CAP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO COUNTER LASHING 40" O.C. MAX. CAULK ALL RIVET HEADS. ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK VICTORIAN OR 1 ON 12 ASTENERS AT LAPS AND STAGGERED; 20" O.C. AND CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT ASTENERS; 40" O.C. MAX. CAULK ASTENER HEADS ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 1 ON 12 = INISH SIDE COUNTERLASHING SUB-LASHING CAP LASHING MANUACTURING PARAPET DETAIL PAGE/ILE VC-40
ASCIA PANEL COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTERLASHING SUB-LASHING MANUACTURING EAVE DETAIL PAGE/ILE VC-41
REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT REGLET CONTINUOUS CAULK AT REGLET CONTINUOUS BEAD O CAULK CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTERLASHING SUB-LASHING REGLET LASHING MANUACTURING HEAD WALL DETAIL PAGE/ILE VC-42
# 30 ELT UNDERLAYMENT ASCIA PANEL ASTENERS; 20" O.C. MAX. LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS VICTORIAN OR # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENER; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE LASHING SUB-LASHING MANUACTURING RAKE WALL DETAIL PAGE/ILE VC-50
REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR REGLET CONTINUOUS CAULK AT REGLET CONTINUOUS BEAD O CAULK # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB-LASHING REGLET LASHING LASHING MANUACTURING RAKE WALL DETAIL PAGE/ILE VC-51
VICTORIAN OR TRANSITION LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEAD CONTINUOUS BEAD O CAULK VICTORIAN OR SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 40" O.C. # 30 ELT UNDERLAYMENT NOTE: PLACE A DAB O CAULK AT ASTENER LOCATION, DRIVE ASTENER THROUGH CAULK, AND CAULK ASTENER HEADS. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 10" MIN. TRANSITION LASHING SUB-LASHING MANUACTURING SLOPE TRANSITION DETAIL PAGE/ILE VC-60
VICTORIAN OR IELD CUT AS REQUIRED TO VALLEY LINE BUTT ENDS OR WEEP DO NOT CAULK IN OR UNDER 9" MIN. CONTINUOUS BEAD O CAULK BETWEEN VALLEY LASHING AND ELT UNDERLAYMENT VALLEY LASHING 1" # 30 ELT UNDERLAYMENT ASTENERS, 24" O.C., PLACE A DAB O CAULK AT ASTENER LOCATIONS, DRIVE ASTENERS AND CAULK ASTENER HEADS 1. (BY OTHERS) TO BE A MINIMUM O PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE ASTEN THROUGH VALLEY UNDER LAP, NO ASTENERS TOP (OVERLAPPING) VALLEY 2 CONTINUOUS BEADS O CAULK AT LAPS ONLY AT TOP O LASHING ARE TO BE EXPOSED ON 12" LAPS 20" MIN. VALLEY LASHING 20" MIN. MANUACTURING VALLEY DETAIL PAGE/ILE VC-70
ROO PIPE PENETRATION O 4" IN DIA. OR LESS RUBBERIZED BOOT LASHING CONTINUOUS CAULK PIPE PENETRATION TO BE IN BODY O SHINGLE VICTORIAN OR SET RUBBERIZED BOOT INTO CONTINUOUS BEAD O CAULK. USE ASTENERS AS SPECIIED BY BOOT MANUACTURER CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT CUT SHINGLE 1" SMALLER THAN PENETRATION, BACK CUT TABS, OLD TABS UP AROUND PENETRATION, AND CAULK. NOTE: I PIPE IS MADE O METAL, IT MUST BE PAINTED TO PREVENT RUST RUN-O ROM STAINING PANELS. NOTE: POSITION SQUARE BASED BOOTS IN A DIAMOND ORIENTATION WHERE POSSIBLE TO AID IN DIVERTING WATER. MANUACTURING PIPE PENETRATION 4" DIA. OR LESS PAGE/ILE VC-80
VICTORIAN OR VC-84 CARRY LASHING ROM VC-82 UNDER VC-84 ROM VC-84 TURN CORNER WITH VERTICAL LEG O LASHING ROM VC-84 VC-82 TURN CORNER WITH VERTICAL LEG O LASHING ROM VC-82 VC-83 CARRY LASHING ROM VC-83 UNDER VC-82 ROM VC-84 NOTE: SHINGLES ARE TO BE IELD CUT TO IT TIGHT AROUND PENETRATION MANUACTURING ROO PENETRATION RECTANGULAR/SQUARE PAGE/ILE VC-81
COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR CONTINUOUS BEAD O CAULK # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB-LASHING MANUACTURING COUNTER LASHING LASHING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-82
COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE LASHING SUB-LASHING COUNTER LASHING MANUACTURING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-83
VICTORIAN OR BUTT ENDS OR WEEP, DO NOT CAULK IN OR UNDER COUNTER LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS CONTINUOUS BEAD O CAULK BETWEEN LASHING AND ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS 9" MIN. SUB LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C., PLACE A DAB O CAULK AT ASTENER LOCATIONS, DRIVE ASTENERS AND CAULK ASTENER HEADS 1. (BY OTHERS) TO BE A MINIMUM O PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTER LASHING LASHING SUB LASHING MANUACTURING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-84