IN-SITU ZIRCONIA OXYGEN ANALYZER < ZIRCOMAT-C > DATA SHEET ZFK, ZRY This oxygen analyzer is used to continuously measure oxygen concentration in combustion exhaust gas of industrial boilers or furnaces, and is ideally suited for combustion monitoring and control. The detector (ZFK) used with the analyzer is directly inserted into the objects measured, eliminating the need for a sampling device and provides quick response. The converter (ZRY) features 3 measuring ranges, one touch calibration and NEMA4 housing. Comparing to the current converter (ZRM), this ZRY is recognized as economical type with simple functions. General-use detector FEATURES. Sampling device is unnecessary Gas sampling devices such as a gas aspirator, a dehumidifier, etc. are unnecessary because of use of directinsertion type detector.. High speed response The adoption of a flow guide tube utilizing the flow of the measured gas assures quick response (less than 7sec). 3. Dust-tight and water-proof housing Aluminum die casting housing of converter satisfies NEMA4 and IP6 standard. 4. 3-measuring ranges and one touch calibration The converter has 0-, 0, vol% 3 ranges easily changed by pin connection and zero and span are simply calibrated by key operation. SPECIFICATIONS General Measuring object: Oxygen contained in noncombustible gas Measuring principle: Direct-insertion zirconia system Measuring range: 0 to, 0 or vol% O (Changed by internal set pin) Repeatability: Within ±.0% of full scale Linearity: ±% of full scale Response time: Within 7sec for 90% response (from calibration gas inlet) Power supply: 00,, 0 or 30V AC, 0/60Hz Power consumption: (approx.) + 0VA (at steady state) + 00VA (at start) Warmup time: Approx. min Converter Oxygen detector (ZFK, ) Measuring detector: For general-use: ZFK For corrosive gas: ZFK Measured gas temperature: system; 0 to +600 C Measured gas pressure: 3 to +3kPa : Flange; JISK 6A FF (JISK-80AFF for high particulate gas) Insertion length; 0.3, 0., 0.7, m (0.8m for high particulate gas) Ambient temperature: 0 to +60 C for cable section C or less at detector flange surface with power applied Structure: Dust/rain-proof structure(iec IP equivalent) Filter: Alumina(filtering accuracy 0μm) and quartz paper Main materials of gas-contacting parts: General-use detector(zfk ); Zirconia, SUS36, platinum, SUS304 Anticorrosive detector(zfk ); Zirconia, tita-nium, platinum, SUS36 ; SUS304 or SUS36 EDSX3-9a Date Sep.0,999
ZFK, ZRY Calibration gas inlet: Brass joint for φ/4 inch tube. Reference air inlet (option): Rc/8 or NPT/8 Detector mounting: Horizontal plane ± 4, ambient surrounding air should be clean. Outer dimensions: (L x max. dia.) 0mm x 00mm (detector) Mass (approx.) {weight}: Detector;.6kg (general-use, m); kg Finish color: Silver and SUS metallic color Oxygen converter (ZRY) Measuring range: 0-, 0, vol% O Changeable by internal set pin. Repeatability: ±.0% of full scale Lineality: ±.0% of full scale Indication: Oxygen concentration; 3-digit LED Oxygen concentration output signal: 4 to 0mA DC (allowable load resistance: 00 Ω or less) Isolated output, linear Fault contact output: 0V AC, A rating (close contact or open contact for fault should be specified when you place an order.) Self-diagnoses: Fault of sensor temperature, zero calibration error, span calibration error Calibration method: Manual calibration with key operation Calibration gas: Recommended calibration gas concentration Zero gas;.0 to.0% O Span gas; 0.6 to.0% O (oxygen concentration in the air) Ambient temperature: 0 to +0 C Ambient humidity: 90% RH or less Power supply: 90 to 0 or 30 V AC, 0/60Hz Construction: Dust-tight, waterproof construction, NEMA4 (corresponding to IP6 of IEC) Material: Aluminum die casting Outer dimensions (H x W x D): 0 X 30 X 9mm Mass {weight}: Approx. 4.kg (excluding cable and detector) Finish color: Munsell 6PB 3./0. (blue): cover, silver; case Mounting method: Mounted flush on panel Exclusine cable (ZRZP) Cable: 4-cores sealed wire (O signal and R- themo couple signal) and -cores cable (power) Cable conduit: Flexible type Length: Refer to code symbols SCOPE OF DELIVERY Detector: Detector main unit x, Viton O ring x, mounting screw (Mmm x ) x 6, thermal sticker x, flow guide tube (as specified) x, ceramic filter x, cover (as specified) x, reference air inlet (as specified) x Converter: Converter main unit x Accessories (AC0V 00mA T fuse x, AC0V 3.A T fuse x ) Items to be prepared separately: () Standard gas for calibration Type ZBM NSK4-0 () Reduction valve for standard gas (type ZBD6003) (3) Flowmeter Type; ZBD03, 0. to L/min (for calibrating gas) CAUTIONS If combustible gas (CO, H etc.) exists in the measured gas, error will occur due to burning at the sensor section. The inclusion of corrosive gas (Si vapor, alkaline metal, P, Pb etc.) will shorten the life of the sensor. When the measured gas temperature is high (+300 C or higher), the flange should be separated from the furnace wall in order to bring the detector flange surface temperature below the specified value + C). The flow guide should be attached in the direction in which the gas flow to the detector decreases. When dust more than g/nm 3 is included in the gas, manual blow down is necessary. The product conforms to the requirements of the Electromagnetic compatibility Directive 89/336/EEC as detailed within the technical construction file number TZ73704. The applicable standards used to demonstrate compliance are : EN 0 : 99 CLASSA Conducted and Radiated emissions EN 008- : 99 Radiated immunity, ESD and FBT ZFK, ZRY
DEVICE CONFIGURATION The device to be combined differ according to the conditions of the gas to be measured. Please select the devices to be combined with reference to the following table. Measured gas Device configuration Application Temperature Gas Flow DUST Protection cover Note Detector type Converter type Ejector type General-use 600 C or (boiler) less Anti-corrosive use (incinerator) to 0m/s Less than 0.g/m 3 [nor] Less than 0g/m 3 [nor] no Less than g/m 3 [nor] yes Fuel; gas, oil Fuel: coal with manual blow down Included high moisture with manual blow down ZFK R 4- ZFK R 4-6 D 8 ZFK R 4-6 E 8 ZRY ZRY ZRY Note () Dust volume is approximate value. () Instrument quality air or bottled air is available as reference air by selecting detector with reference air inlet, when oxygen concentration in air around sensor changes. CODE SYMBOLS (Detector) 4 6 7 8 ZFK R 4 3 9 03 0 Y 0 A 3 A A 7 A B 3 B B 7 B 6 D 8 6 E 8 Y A Y A B Cal. gas inlet For φ/4 inch tube ( Replacement Detector element) 4 6 7 8 ZFK R 4 3 9 03 Description Application General use. For corrosive gas (refuse incinerator) Power supply 00/VAC 0/60Hz 00/0VAC 0/60Hz 30VAC 0/60Hz (CE-marking approved) flange application length SUS304 general use 300mm SUS304 general use 00mm SUS304 general use 70mm SUS304 general use 000mm SUS36 for corrosive gas 300mm SUS36 for corrosive gas 00mm SUS36 for corrosive gas 70mm SUS36 for corrosive gas 000mm SUS36 for high particulate 800mm SUS36 for high particulate with 800mm cover Protection cover Without With Reference air inlet Non Rc/8 NPT/8 Description Application General use. For corrosive gas (refuse in cinerator) Cal. gas inlet For φ/4 inch tube Power supply 00/VAC 0/60Hz 00/0VAC 0/60Hz 30VAC 0/60Hz (Converter) 3 4 6 7 8 9 0 Z R Y Y - R 0 B C (Exclusive-special cable) 3 4 6 7 8 Z R Z PR P R YA YB YC YD YE YF YG YH YJ YK YL YM AA BB CC DD - 9 0 Y E Description Connectable devices For ZRY Types For R thermocouple Conduit length Cable length 6m 0m m 0m 30m 40m 0m 60m 70m 80m 90m 00m 6m 6m 0m 0m m m 0m 0m Cable end treatment One side (detector side) Both sides Note: Description Output signal and fault output 4 to 0mA DC, close contact 4 to 0mA DC, open contact Power supply 90 to 30V AC 0/60Hz (CE marking approved) Mounting method Panel mounting Instruction manual NO YES (English) For connection between detector and converter, the conduit to be used should be rainproof flexible type. 3
ZFK, ZRY CONFIGURATION system Cover for retaining warmth Status of fault contact output Detector ZFK digit of model Power off Power on and normal Power on and fault B open open close Gas temperature. 600 C max. C open close open Sample gas outlet *3 Ball valve 3 4 6 Bule Black Red Yellow White White Rainproof flexible conduit. 0m max. Gas temperature. 600 C max. -core cable 4-core cable Thermocouple signal Zirconia signal Converter (ZRY) Analog output Fault contact output Sensor heater for high particulate 6mm or 4 inch tube for calibration gas (not supplied) *3 Ball valve 3 4 6 7 8 9 0 3 4 Red White Blue Yellow Cell/thermocouple output Heater power supply DC4 to 0mA Black White AC power supply Sample gas outlet Gas temperature. 600 C max. Flow guide for high particulate with cover Change valve Reduction valve (ZBD6) to Detector * Ref. air Flowmeter (ZBD4) ( to.l/min) Standrad gas for zero point (ZBM) Reduction valve (unnecessary when supply air pressure is 0 to 00kPa * Air supply (0. to 0.L/min) Reduction vale (ZBD6) * Standard gas for span point (ZBM) Note * Sandard gas or instrumentation air can be used in place of span gas. * Instrument quality air or bottled air is available as reference air instead of ambient air, when oxygen concentration in air around sensor changes. *3 Blow down air inlet pressure in 00 to 300kpa. 4
60 OUTLINE DIAGRAM (Unit:mm) Detector (ZFK) Proof cover (to order) Approx. 30 Approx. 6 Approx. 8 80 4.4 36 6 Filter EXTERNAL CONNECTION DIAGRAM 8 Heater Thermocouple Element output A Approx. Ref. air inlet (to order) NPT/8 or Rc/8 6-6 3 4 6 Black / White/ Red / White/ Yellow / Blue -core wire 4-core wire Exclusive-special cable Exclusive cable gland Calibration gas inlet for /4 inch tube. Approx. L Approx. 0 30 Gas inlet 0 34 Z F K R 4 - A 3 7 Gas outlet 6-M detector side Oxygen detector Cord th L (m) MASS Approx (kg) 3 7 0.3 0. 0.7.0.7 3.3 4. 4.8 Z L= (to order) 8 MTG. holes
ZFK, ZRY Detector (ZFK) Proof cover (to order) Approx. 30 Approx. 6 Approx. 8 80 4.4 36 6 Filter EXTERNAL CONNECTION DIAGRAM 8 Heater Thermocouple Element output 60 Approx. 3 Ref. air inlet (to order) NPT/8 or Rc/8 6-6 3 4 6 Black / White/ Red / White/ Yellow / Blue -core wire 4-core wire Exclusive-special cable Exclusive cable gland Calibration gas inlet for /4 inch tube. 3 Approx. L Approx. 40 30 Gas inlet 60. Z F K R 4 - B 3 7 Gas outlet 6-M detctor side Oxygen detector Cord th L (m) MASS Approx (kg) 3 7 0.3 0. 0.7.0 3.3 4. 6. 7.6 Z L= (to order) 8- MTG. holes 6
(for high particulate) 4 - Rc /4 with plug int thd. 80 4 Blow down air inlet 8-9 MTG. hole Select an upper port to avoid the condensation in the piping 9. Flange: JIS K80A FF ZFK MTG. position Packing 8 Z F K R 4-6 D8 0 Gas outlet 800 30 Gas flow Tube (0A SCH40) (for high particulate with cover) 4 - Rc /4 with plug int thd. 80 4 8-9 MTG. holes Blow down air inlet Select an upper port to avoid the condensation in the piping 9. Flange: JIS K80A FF ZFK MTG. position Packing (7) 0 Z F K R 4-6 E8 Gas outlet (790) 800 30 Gas flow Protection tube (6A SCH40) (38) Tube (0A SCH40) 7
ZFK, ZRY Converter (ZRY) Panel flush mounted -φ9 7 3 0 0 3. 9 4 30 CABLE GRAND φ 39 -G/ 40 40 40 40 CONNECTION DIAGRAM 3 4 6 7 8 9 0 3 4 + + + L N THERMO- COUPLE ELEMENT INPUT OUTPUT SIGNAL FAULT CONTACT OUTPUT HEATER POWER FOR SENSOR POWER SUPPLY Fuji Electric Your distributor: Coulton Instrumentation Ltd 7 Somerford Business Park, Christchurch, BH3 3RU, UK Tel: +44 0 480 303 E-mail: sales@coulton.com Web: www.coulton.com Information in this catalog is subject to change without notice. Printed in Japan