Specification for Approval (Ver 1.0) Part No. : LWH1000N comments LUXPIA Co., Ltd. Designed by Checked by Approved by Approved by Approved by Approved by / / / / / / Date :... Date :... LUXPIA CO.,LTD. 948-1, Dunsan-Li Bongdong-Eup, Wanju-Gun, JeonBuk, Korea Tel 82-70-8671-2400 Fax 82-70-8620-8080
- CONTENTS - 1. Features 2. Package Outline Dimensions and Materials 3. Absolute Maximum Ratings 4. Electro-Optical Characteristics 5. CIE Chromaticity Diagram 6. Materials 7. Taping 8. Packing 9. Reliability 10. Cautions 11. Warranty 12. Others 13. Characteristic Diagrams 1/14
1. Features Package : SMD type ( 1 Chip in 1 PKG ) 1.6 0.8 0.4 mm 2 2. Package Outline Dimensions and Recommended Solder Patterns 2/14
3. Absolute Maximum Ratings (T a =25) item symbol value unit forward current I F 20 ma pulse forward current 1) I FP 100 ma reverse current V R 5 V power dissipation P D 70 mw operating temperature T opr -30 to+85 storage temperature T stg -40 to +100 1) I FP conditions : pulse width 10msec & duty ratio 1/10 4. Electro-Optical Characteristics (T a =25, I F =5mA) item rank symbol condition min typ max unit forward voltage 2) luminous intensity 3) V27 2.70-2.80 V F V28 I F = 5mA 2.80-2.90 V29 2.90-3.00 2E12 120-160 2E16 160-200 I V I F = 5mA 2E20 200-250 V mcd 2E25 250-300 reverse - I R V R =5V - - 50 current 2) Forward voltages are tested at a current pulse duration of 10 ms and an accuracy within ±0.1V. 3) The allowance of luminous intensity measurement is within ±11%. * To avoid optical difference, please do not mix differently ranked product. * All measurements were made under the standardized environment of LUXPIA. 3/14
5. CIE Chromaticity Diagram 4) (T a =25, I F =5mA) 4) The allowance of color coordinates measurement is within ±0.01. (CIE1931 standard colorimetric system) 4/14
6. Materials item LED chip Wire PCB encapsulation material InGaN gold C3965 (Cu/Ni/Au plating) Epoxy + Silicone resin 7. Taping 7.1. tape (material : PS conductive, 10 4 ~10 5 Ω) (units : mm) 5/14
7.2. wheel (color : black, material : PS conductive, 10 9 ~10 12 Ω) (units : mm) - quantity per reel LWH1000N : 5,000pcs 7.3. label part no. LWH1000N size (L X W) : 85mm 50mm A 2E20 V27 5,000ea color rank I V rank V F rank 6/14
8. Packing The LEDs are packed in cardboard boxes after taping. The label shows part number, lot number, rank, and quantity. In order to protect the LEDs from mechanical shock, they are packed with cardboard boxes for transportation. The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so cautions must be taken to prevent any possible damage. The boxes are not water-resistant and, therefore, must be kept away from water and moisture. When the LEDs are transported, it is recommended that the same packing method as Luxpia's is used. If noticeable damage on a box appears upon arrival at the user s warehouse, the user should submit a claim to Luxpia within one week after arrival of the products. 7/14
9. Reliability 9.1. test items and results no. 1 2 test item resistance to soldering heat (reflow) solderability (reflow) 3 temperature cycle 4 5 6 7 8 9 high temperature storage high humidity and temperature storage low temperature storage steady-state operating lifetime test steady-state operating lifetime of high humidity and temperature steady-state operating lifetime of low temperature Standard Test Method JESD22-B106 EIAJED4701-200 JESD22-B102 EIAJED4701-100 JESD22-A104 EIAJED4701-200 JESD22-A103 EIAJED4701-200 JESD22-A101 EIAJED4701-200 JESD22-A103 MIL-STD-883E JESD22-A108 - MIL-STD-810F JESD22-A108 Test Conditions Note number of damaged sample T sld =260 o C, 10sec (pre treatment 2 times 0/45 30 o C,70%,168hrs) T sld =215±5 o C, 3sec 1 time over 95% 0/45-40 o C through +25 o C to +100 100 cycles 0/45 (30min/5min/30min) T a =100 1000 hrs 0/45 T a =60, RH=90% 1000 hrs 0/45 T a =-30 1000 hrs 0/45 T a =25, I F =10mA 500 hrs 0/45 T a =60, RH=90%, I F =5mA 500 hrs 0/45 T a =-30, I F =10mA 500 hrs 0/45 * LED with Luxpia standard circuit board 9.2. criteria for judging the damage item symbol test condition criteria for judgement min max forward voltage V F I F = 5mA - U.S.L. 5) 1.2 luminous intensity I V I F = 5mA L.S.L. 6) 0.5-5) U.S.L. : upper standard level L.S.L. : lower standard level 8/14
10. Cautions White LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of White LEDs is subject to change a little by an operating current. Care should be taken after due consideration when using LEDs. (1) Moisture-Proof Package When moisture is absorbed into the SMT package it may vaporize and expand products during soldering. There is a possibility that this may cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture-proof package is used to keep moisture to a minimum in the package. A package of a moisture-absorbent material (silica gel) is inserted into the shielding bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage Storage Conditions - After opening the package : The LEDs should be kept at 5~30 or less and 60%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture-proof packaging with moisture-absorbent material (silicagel) is recommended. If unused LEDs remain, they should be stored in moisture-proof packages, such as sealed containers with packages of moisture-absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture-proof bag and to reseal the moisture-proof bag again. If the moisture-absorbent material (silica gel) has faded away or the LEDs have exceeded the recommended storage time, baking treatment should be performed using the following conditions. - Baking treatment : more than 24 hours at 125±5 (This condition is LED standards which are not in the reel) Luxpia's LED electrode sections are comprised of a silver-plated copper alloy. The silver surface may be affected by environments which contain corrosive gases and so on. Please avoid condition which may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when the system is designed. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in the specification. The operating current should be decided after considering the ambient maximum temperature of LEDs. 9/14
(4) Soldering Conditions The LEDs can be soldered in place using the reflow soldering method. Luxpia does not make any guarantee on the LEDs after they have been assembled using the dip soldering method. Recommended soldering conditions Reflow Soldering Hand Soldering Lead Solder Lead-free Solder pre-heat 120~150 200~220 temperature 350 max pre-heat time 120sec max 120sec max soldering time 3sec max peak temperature soldering time condition 240 max 10sec max refer to profile * After reflow soldering, rapid cooling should be avoided. 260 max 5sec max refer to profile (one time only) [temperature-profile (surface of circuit board)] Use the conditions shown to the following figures. < : Lead Solder> < : Lead-free Solder> 10/14
Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a doublehead soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Reflow soldering should not be done more than two times. When soldering, do not put stress on the LEDs during heating. After soldering, do not warp the circuit board. (5) Cleaning It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (6) Static Electricity Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an antielectrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded. It is recommended that measurements be taken against surge voltage to the equipment that mounts the LEDs. When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a V F test at a lower current (below 1mA is recommended). Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. - criteria : V F > 2.0V at I F =0.5 (7) Others Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LEDs with matrix drive. The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. 11. Warranty (1) Luxpia warrants that its LEDs conform to the foregoing specifications and that Luxpia will convey good title to all LEDs sold. (2) LUXPIA disclaims all other warranties including the implied warranties of merchantability and fitness for a particular purpose. (3) In the event any LED supplied by Luxpia is found not to conform to the foregoing specifications within ninety days of receipt, Luxpia will repair or replace the LED, at Luxpia s discretion, provided that the User (a) promptly notifies Luxpia in writing of the details of the defect (b) ships the LEDs at the User s expense to Luxpia for examination, and (c) the defect is due to the negligence of Luxpia and not mishandling or misuse by the User. (4) Luxpia will not take responsibility for any trouble that is caused by using the LEDs at conditions exceeding our specifications. (5) These specifications are applied only when a LED stands alone and it is strongly recommended that the User of the LEDs confirms the properties upon assembly. Luxpia is not responsible for failures caused during and after assembling. It will be excepted from the rule if the failure would caused undoubtedly by Luxpia. 11/14
(6) A claim report stating details about the defect shall be made when returning defective LEDs. Luxpia will investigate the report immediately and inform the user of the results. (7) The LEDs described in the specification are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices) (8) LUXPIA s liability for defective lamps shall be limited to replacement and in no event shall LUXPIA be liable for consequential damage or lost profits. 12. Others (1) The warranties of quality set forth herein are exclusive. All previous negotiations and agreements not specifically incorporated herein are superseded and rendered null and void. (2) Both parties shall sincerely try to find a solution when any disagreement occurs regarding these specifications. (3) User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Luxpia. When defective LEDs are found, the User shall inform Luxpia directly before disassembling or analysis. (4) These specifications can be revised upon mutual agreement. (5) Luxpia understands that the User accepts the content of these specifications, if the User does not return these specifications with signatures within 3 weeks after receipt. 12/14
13. Characteristic Diagrams (1) forward voltage vs. forward current (2) forward current vs. relative luminosity (T a =25) (T a =25) forward current IF [ma] relative luminosity [a.u.] forward voltage V F [V] forward current I F [ma] (3) ambient temperature vs. allowable forward current (4) ambient temperature vs. relative luminosity allowable forward current IAF[mA] relative luminosity[a.u.] (I F =5mA) ambient temperature T a [] ambient temperature T a [] 13/14
(7) relative spectral emission V(λ) = standard eye response curve (T a =25, I F =5mA) (8) radiation characteristics (T a =25, I F =5mA) Relative Luminous Intensity Iv[%] 14/14