MPS Series
D e s c r i p t i o n The MPS spin-on filter series is a complete product range suitable, for both suction and return applications. Utilising spin-on canisters, the MPS series are quick and easy to service and provide a clean solution when changing elements. The filter elements are either resin-impregnated paper (ßx>), glass fibre (ßx³ ) or square wire mesh. The unique filter head is designed for both European CS and American CG standard canister series. One head design series accomodates both styles of elements. Also available is a new design utilizing a pressure differential visual and electrical indicators - ideal for lubrication applications. MPS filters are specifically designed for contamination control in hydraulic and lubrication circuits for mobile applications, agricultural and machine tool systems. The CW series of canister removes water from oil while filtering the oil at the same time. Water absorbent polymers up to 8 times their own weight, provide this major feature. Water holding capacities: - CW - 4 ml. CW 1-788 ml. DIFFERENTIAL INDICATORS For Use with series 1 filter heads. New absolute filter elements independently tested in the following Institutes: For Use with series filter head. SUCTION INDICATORS ELECTRICAL VISUAL RETURN LINE INDICATORS VISUAL UNI EN ISO 91 N 37/98 ELECTRICAL MPS /3./UK
F i l t r a t i o n t e c h n o l og y element: Materials End caps: Galvanized steel Support tube: Galvanized steel Support frames: Galvanized steel with an epoxy coating A Series Inorganic microfibre Pre-filtration and External support media External wire mesh Inner support tube Internal wire mesh Microfibre filtration media Internal support media MP elements - Conform to the following ISO standards ISO 941 - Verification of collapse/burst resistance. ISO 94 - Verification of fabrication integrity and determination of the first bubble point. ISO 943 - Verification of material compatibility with fluids. ISO 373 - Method for end load test. ISO 374 - Verification of flow fatigue characteristics. ISO 3968 - Evaluation of pressure drop versus flow characteristics. ISO 16889 - Multi-pass method for evaluating filtration performance. Element material Absolute filtration A Series Inorganic microfibre with acrilic support Contamination retention as per ISO 16889: Multi-pass test. New improved ß ³ filter elements with greater efficiency and increased dirt holding capacity elements A3 A6 A1 Dimensions for ß (µm) values ß ³ ß ³ ß ³ 7 ß ³ (%) (9%) (98,7%) (99,%),4 3 3 4,6 6 3 6 7,8 1 13 19 N.B. Other materials giving different degrees of filtration are available on request. ß 8 1, Filtration ratios ß 1 ß > 1. > 1. >. > 1. ³ > 1. > 1, > 3 D P (bar) 7 7 7 7 ing area elements CS-CG-CT A3/A6 A1/ 7 1 19 316 39 19 316 39 1 39 39 Values in cm Element material Nominal filtration P Series Resin - impregnated paper M Series Square wire mesh (filtration degree is defined in microns by the maximum diameter of a sphere corresponding to the mesh size) ing area elements CS-CG-CT P1/P M 7 1 1 44 414 43 76 1 17 199 4 CWSeries Resin - impregnated paper M6 M9 1 17 199 4 1 17 199 4 Values in cm CW 1 P1/P 3
S p e c i f i c a t i o n Materials Head Aluminium Bypass valve Nylon Working temperature Pressure filter body Collapse pressure filter elements Seals A Series: Nitrile (Buna-N) V Series: Viton Maximum working pressure up to Indicator Brass From - to +11 C For temperatures outside this range, please consult our Sales Network Organization 1 bar 4 bar Bypass valve Calibration pressure s of indicators for MPS series (MPS -7-1 ) and MST series Visual indicator Electrical indicator Bypass valve, differential opening pressure: S series:,3 bar ± 1% (MPS series only) R series: 1,7 bar ± 1% Description: MPS series filters are fitted with indicators 1 Kpa =.1 bar switching: Suction filters at a pressure of: kpa ± 1% Line filters at a pressure of: 1,3 bar ± 1% (MPS series only) Return filter at a pressure of: 1,3 bar ± 1% (MPS-MST series only) Suction filter: (MPS series only) VS vacuum switch Return and line filter VA Pressure gauge VR colour coded pressure gauge Suction filter (MPS series only) E Vacuum switch with change over contact Return filter ER Pressure switch with N.O. contacts EC Pressure switch with N.C. contacts s of indicators for MPS series 1 (MPS 1-71-11-11-31-31) MPS filter series 1 (1-71-11 and so on) are fitted with, differential style indicators. Visual indicator Electrical indicator Visual-electrical indicator scale - 76 cm Hg scale - 1 bar scale - 6 bar Operational information: 1V - Z1 Series for with bypass set switching at 1, bar ± 1% to 1,7 bar V6 - Z6 Series for without bypass switching at bar ± 1% N1 Series for with bypass set switching at 1, bar ± 1% to 1,7 bar N6 Series for without bypass switching at bar ± 1% 1E - K1* Series for with bypass set switching at 1, bar ± 1% to 1,7 bar E6 - K6* Series for without bypass switching at bar ± 1% *For K visual-electrical indicator, specify the voltage (il. K61 = LED: 4 volt) Switching at kpa ± 1% Max voltage: V 6 Hz Max current: A resistive, A inductive Protection degree IP6 Switching at 1,3 bar ± 1% Max voltage: 48V 6 Hz Max current:,a resistive,a inductive * 1-4 Volt { - 11 Volt 3-3 Volt
S p e c i f i c a t i o n Pressure differential indicator option K - E - N Series Supply voltage (/6 Hz) (V) Vca 1 Vca Vcc 3 Vcc 1 Vcc Resistive load (A),, Inductive load (A) 3,3,3 CONNECTOR DIN 436 ELECTRICAL CONNECTION E - N SERIES N.C. N.O. ELECTRICAL CONNECTION K SERIES N.C. N.O. Visual V series Visual Z series Ø16 G1/ Ø16 G1/ Electrical N series Visual led - Electrical K series Led Visual - Electrical E series, Ø16 G1/ Ø16 G1/ Ø16 G1/
S p e c i f i c a t i o n Fluid Compatibility head and bowls compatible for use with: mineral oils (types HH-HL-HM-HR-HV-HG as per ISO 6743/4) water-based emulsions (types HFAE-HFAS as per ISO 6743/4) synthetic fluids (types HS-HFDR-HFDS-HFDU as per ISO 6743/4) water-glycol (types HFC as per ISO 6743/4) Seals A Series Nitrile (Buna-N) compatible with mineral oils (types HH-HL-HM-HR-HV-HG as per ISO 6743/4) water-based emulsions (types HFAE-HFAS as per ISO 6743/4) water - glycol (types HFC as per ISO 6743/4) V Series Viton compatible with synthetic fluids (types HS-HFDR-HFDS-HFDU as per ISO 6743/4) elements As per ISO 943; suitable for mineral oils (types HH-HL-HM-HR-HV-HG as per ISO 6743/4) and synthetic fluids (A and M series only) (types HS-HFDR-HFDS-HFDU as per ISO 6743/4) For water-based emulsions (types HFAE-HFAS as per ISO 6743/4) and fluids other than those mentioned, please consult our Sales Network Organization. International standards for contamination fluid control A general (no direct) comparison between ISO 446 and NAS 16 is given in table below. Contamination Correspondent Recommended Typical applications codes codes filtration ISO 446 NAS 16 degree 4µm(c) 6µm(c) 14µm(c) B x ³ 14 1 9 3 3 High precision and laboratory servo-systems 17 1 1 6 3-6 Robotic and servo-systems 18 16 13 7 1-1 Very sensitive - high reliability systems 18 1 9 1-1 Sensitive - reliable systems 1 19 16 1 1- General equipment of limited reliability 3 1 18 1-4 Low - pressure equipment not in continuous service
S e l e c t i o n & i n s t a l l a t i o n i n f o r m a t i o n elements types Pl eas e r e fe r t o A Series P Series M Series Absolute inorganic microfibre Nominal cellulose impregnated Metal mesh media, available in filtration media, available in paper media, available in 1, 6, and 9 micron. 3, 6, 1 and micron and micron. Example - M, M6 or M9. Example - A3, A6, A1 or Example - P1 or P in div i d ual pr e ss ur e dr o p cu r ve s t o ob t ai n f ilt er a ss emb ly pre ss ur e dr o p i n fo r mat io n The following filter sizing recommendations are based using a mineral oil fluid at 3 mm /s (cst) with a maximum total filter (housing and filter element) pressure drop of 3% of the filter condition indicator (.4 bar) for line and return filter and 8 kpa for suction filter. Indicator port for return line filter IN MPS -7 Series C - No. Threaded holes Ø 96 OUT Indicator port for suction line filter Lengths MPS 1-71 Series Indicator for suction filter MPS -7 (only for option G1-G) ø 4 B 14 3 9 VS 9 9 EO 4 1/8 BSP Revolving PG 11 ø Cable 8/1 H H1-1 18 7-71 48 68 Indicator port Indicator for return filter MPS -7 (only for option G1-G) VR - VA A/F.14 ER - EC 6 43 A/F.4 Pg 7 MPS -71 Thread connections MPS SERIES -1 SIZES A3 A6 A1 P1 M6-M9 Flow rates with 3 mm /s fluid viscosity including filter element A B C G1 3/4 BSP 1/8 BSP M6 G 3/4 NPT 1/8 NPT 1/4 UNC G3 SAE 1-1 1/16-1 UN 1/8 NPT 1/4 UNC G4 SAE 8-3/4-16 UNF 1/8 NPT 1/4 UNC G 1 BSP 1/8 BSP M6 G6 1 NPT 1/8 NPT 1/4 UNC 1 7, MPS SERIES 7-71 SIZES A3 A6 A1 P1 M6-M9 4 44 48 8 4 49 3 63 8 9 11 14 18 16 4 11 13 1 18 6 SEE TABLE BELOW SEE TABLE BELOW 1, 1,3 Suction filter - Housing pressure drop ø 4, Indicator for line filter MPS 1-71 Led.,4 1 1 3 Return line filter - Housing pressure drop,3, Z V N K E,1 1 3 4 6 7 9
S e l e c t i o n & i n s t a l l a t i o n i n f o r m a t i o n Pl eas e r e fe r t o in div id ual pr e ss ur e dr o p cu r ve s t o o b t ai n f ilt er a ss e mb ly pre ss ur e dr o p i n fo r mat io n The following filter sizing recommendations are based using a mineral oil fluid at 3 mm /s (cst) with a maximum total filter (housing and filter element) pressure drop of 3% of the filter condition indicator (.4 bar) for line and return filter and 8 kpa for suction filter. Indicator por t for return line filter C - No. Threaded holes MPS SERIES 1-11 SIZES IN OUT Indicator por t for suction line filter Lengths MPS 1-11 H H1 1-11 41 66 1-11 86 311 A3 A6 A1 P1 M6-M9 7 8 11 14 13 16 19 4 3 6 1 1/4 MPS SERIES 1-11 SIZES, Ø 19 MPS 1-1 Series 16 3 B MPS 11-11 Series 8 Indicator port A3 A6 A1 8 18 1 11 3 16 4 1 1/4,3 P1 M6-M9 1 4 68 9 1/8 BSP Indicator for return filter MPS 1-1 (only for option G1) ø 4 133 Indicator for suction filter MPS 1-1 (only for option G1) ø 4 VS VR - VA A/F.14 Indicator for line filter MPS 11-11 EO ER - EC 6 43 A/F.4 133 Thread connections Led Revolving PG 11 ø Cable 8/1 Pg 7. Flow rates with 3 mm /s fluid viscosity including filter element A B C G1 1 1/4 BSP 1/8 BSP M8 G 1 1/4 NPT 1/8 NPT /16 UNC G3 SAE - 1 /8-1 UN 1/8 NPT /16 UNC Suction filter - Housing pressure drop 1 7,, 1 3 4 6 7 9 Return line filter - Housing pressure drop,4,3,,1 3 7 1 14 17 1 Z V N K E
& S e l e c t i o n i n s t a l l a t i o n i n f o r m a t i o n Pl e as e r e fe r t o in div i d ual pr e ss ur e dr o p cu r ve s t o o b t ai n f ilt e r a ss emb ly pre ss ur e dr o p i n fo r mat io n The following filter sizing recommendations are based using a mineral oil fluid at 3 mm /s (cst) with a maximum total filter (housing and filter element) pressure drop of 3% of the filter condition indicator (.4 bar) for line and return filter and 8 kpa for suction filter. MPS SERIES SIZES MPS - A3 13 3 A6 17 4 A1 6 1 1/ 4, 9 11 46 7 7 P1 M6-M9 7 1 1 IN OUT MPS SERIES SIZES indicator (return) indicator (suction) A3 A6 Line Flow rate l/min * 18 1 Suction Flow rate l/min * 6 A1 31 8 1 1 1/ 4, P1 M6-M9 8 118 13 Flow rates with 3 mm /s fluid viscosity including filter element Ø 19 Lengths H 16 61 H1 41 86 14 Thread connections G1 G G3 1 A 1 1/ BSP 1/8 BSP 1 1/ NPT 1/8 NPT SAE 4-1 7/8-1 UN B 1/8 NPT Suction filter - Housing pressure drop C M1 3/8 UNC 3/8 UNC Indicator for suction filter (only for option G1) VS 9 EO Revolving 7,, ø 4 PG 11 ø Cable 8/1 1/8 BSP 7 1 1 1 Return line filter - Housing pressure drop,4,3 Indicator for return filter (only for option G1) ø 4 VR - VA A/F.14 ER - EC 6 43 A/F.4 Pg 7,,1 6 1 18 4 3 36
S e l e c t i o n & i n s t a l l a t i o n i n f o r m a t i o n Please r e fe r t o in di v id ua l pr e ss ur e d r o p c ur ves t o o bt ai n f i l t e r a ss e m bl y p re ss ur e d r o p i n f or ma t io n The following filter sizing recommendations are based using a mineral oil fluid at 3 mm /s (cst) with a maximum total filter (housing and filter element) pressure drop of 3% of the filter condition indicator (.4 bar) for line and return filter and 8 kpa for suction filter. indicator (suction) indicator (return line) D indicator (suction) Indicator port for MPS 31-31 indicator (return line) indicator (return line) Lengths 3-31 3-31 Indicator for suction filter MPS 3-3 (only for option G1-G-F1) ø 4 VS Ø 19 83 1 A OUT IN A 186 F - No. 4 Threaded holes 9 EO Revolving PG 11 ø Cable 8/1 MPS 3-31 H H1 6 9 31 33 Thread connections Flange MPS SERIES 3-31 SIZES A3 A6 A1 P1 M6-M9 Flow rates with 3 mm /s fluid viscosity A B C D E F connections F1 1 1/ SAE 3 PSI/M 1/8 BSP M1 69,8 3,71 M1 F 1 1/ SAE 3 PSI/UNC 1/8 NPT 1/ UNC 69,8 1 MPS SERIES 3-31 SIZES A3 A6 A1 P1 M6-M9 13 17 9 7 Line Flow rate l/min * 18 1 31 8 3 4 6 11 1 1 Suction Flow rate l/min * 6 8 1 118 13 including filter element 1 1/ 1 1/ A B G1 1 1/ BSP 1/8 BSP G 1 1/ NPT 1/8 NPT G3 SAE 4-1 7/8-1 UN 1/8 NPT,4,6 Suction filter - Housing pressure drop C M1 3/8 UNC 3/8 UNC 3,71 1/ UNC 1/8 BSP Indicator for return filter MPS 3-3 (only for option G1-G-F1) VR - VA A/F.14 ER - EC 6 43 A/F.4 Pg 7 7,, 7 1 1 1 ø 4 Indicator for line filter MPS 31-31 Led.,4,3, Return line filter - Housing pressure drop,1 6 1 18 4 3 36 Z V N K E Datasheet Reference: HM-19