e l b a t adjus Hydraulic Damper (HB)
EL2 = 2x + 40 M5x5 Ø15 Ø6 M5x5 Size 6/15 : (Extension and compression force 20N to 800N) size EL1 V0 V0 A 6 100 240* V0 = Thread V0 = Thread 6 = 6/15 25 90* S2 = S2 = 50 140* B3 = B3 = 75 190* G5 = G5 = 100 240* 350 N R7 = R7 = 340* 300 N J3 = Ball socket J3 = Ball socket S2 Technical advices: * the length of chosen s has to be added EL1 = EL2 + s B3 G5 R7 Ball socket J3 force = 50N. Please indicate in case of an order. EL2 = 2.45 x + 47 Chosen s have to be secured
EL2 = 2x + 50 M8x8 Ø22 Ø8 M8x9 Size 8/22 : (Extension and compression force 30N to 1.800N) B0 N0 A 1 100 250* size EL1 B0 = Thread N0 = Thread 1 = 8/22 50 * 1. 1. S3 = S3 = 100 250* 1. 1. A3 = A3 = 350* 1. 1. C5 = C5 = 200 450* 1.000 N 1. A7 = A7 = 250 550* 1.000 N 1. S3 Technical advices: * the length of chosen connecting parts has to be added EL1 = EL2 + s A3 C5 A7 Ball socket P3 force = 100N. Please indicate in case of an order. EL2 = 2.38 x + 55 Chosen s have to be secured
EL2 = 2x + 60 M8x8 Ø28 Ø10 M8x9 Size 10/28 : (Extension and compression force 30N to 3.000N) H0 N0 A 3 300 660* size EL1 H0 = Thread S3 = A3 = C5 = A7 = N0 = Thread S3 = A3 = C5 = A7 = 3 = 10/28 100 200 250 300 350 400 500 260* 360* 460* 560* 660* 760* 860* 1060* 2.500 N 2.000 N 1.500 N 1.000 N S3 Technical advices: * the length of chosen s has to be added EL1 = EL2 + s A3 C5 A7 Ball socket P3 force = 100N. Please indicate in case of an order. EL2 = 2.35 x + 60 Chosen s have to be secured
EL2 = 2x + 75 MF14x15 Ø40 Ø14 MF14x15 Size 14/40 : (Extension and compression force 30N to 10.000N) Z0 Z0 A B 400 875* size EL1 Z0 = Thread S5 = B4 = L5 = C8 = Z0 = Thread S5 = B4 = L5 = C8 = B = 14/40 100 200 300 400 500 600 700 800 275* 375* 475* 675* 875* 1.075* 1.275* 1.475* 1.675* 8.000 N 6.000 N 4.000 N * the length of chosen s has to be added EL1 = EL2 + s S5 B4 L5 C8 Technische Hinweise: force = 200N. Please indicate in case of an order. EL2 = 2.32 x + 82 Chosen s have to be secured
Hydraulic damper (HB) Technical advices / installation recommendations To consider: The maximum loads and pull direction may not be exceeded. There must be a mechanical limit stop approx. 1-2 mm before end of. Mounting of the dampers is in any position possible. The s should be secured against rotation. Due to constructional reasons, Type has a free travel of approx. 20 % For a function without free travel, Type has to be chosen. Adjustment of the dampers: - An adjustment is only possible in completely inserted or extended position - The force can be adjusted by turning the piston as described below. Thereby, the length EL2 will be extended by max. 6 mm. Please take care during the adjustment that you don't damage the adjustment segment by turning it too strong against the limit stop. In case of considerable resistance, please stop the adjustment. The dampers of Type can be adjusted either in completely inserted or extended position. The dampers of Type can be adjusted in completely extended position. 1. Hold the. 2. Adjust the damper by turning the. In case of adjustment with extended, please pull the slightly during the turning process until the piston locks. In case of adjustment with inserted, the has to be pushed slightly until it locks. Turning to the right: Damping will be increased, speed will be reduced Turning to the left: Damping will be reduced, speed will be increased