Proportional damper actuator, non-spring return, Multi-Function Technology Torque min. Control to 0 VDC (DEFULT) Feedback to 0 VDC (DEFULT) For proportional modulation of dampers in HVC systems. The is a non-spring return type actuator. When supply power is removed the actuator will maintain its last position. 9D5 Technical Data Power supply Power consumption Transformer sizing Electrical connection Overload protection Operating range Y* Input impedance Feedback output U* Torque* VC, ± 0%, 50/0 Hz VDC, ±0% running:.5 W; holding:. W 5 V (Class power source) ft, 8 G, appliance cable, / conduit connector electronic throughout 0 to 95 rotation to 0 VDC, to 0 m (w/500 Ω, / W resistor) ZG-R0 00kΩ for to 0 VDC (0. m) 500Ω for to 0 m 500Ω for PWM, Floating point and On-Off control to 0 VDC, 0.5 m max min (8 Nm) Direction of rotation* reversible with switch CW/CCW CW=CW with decrease in signal CCW=CCW with a decrease in signal ngle of rotation* 0 to 95, adjust with mechanical stops Running time* 50 seconds constant ngle of Rotation Off (Default) daptation* Override control* Min. (Min Position) = 0% ZS (Mid. Position) = 50% Max. (Max. Position) = 00% Manual override Manual push button Position indication clip on indicator Humidity 5 to 95% RH, non-condensing mbient temperature - to + F (-0 to +50 C) Storage temperature -0 to +7 F (-0 to +80 C) Housing Housing material NEM, IP5 (with cable entry down) UL 9-5V (flammability rating) Noise level less than 5 d () gency listings UL 87 listed, CE, CS C. No. certified Quality standard ISO 900 Servicing maintenance free Weight.8 lbs. (.kg.) * Variable when configured with MFT options Default/ The default parameters for to 0 VDC applications of the actuator are assigned during manufacturing. If necessary, custom versions of the actuators can be ordered. The parameters noted in the Technical Data table are variable. These parameters can be changed by three means: Pre-set configurations from elimo Custom configurations from elimo s set by the customer using the MFT-Handy or the MFT-ctuate PC software application. Operation The actuator provides 95 of rotation and is provided with a position indicator. The actuator will synchronize it s mechanical stop or the damper or valves mechanical stop and use this point for its zero position during normal control operations. The actuator uses a brushless DC motor which is controlled by an Specific Integrated Circuit (SIC) and a microprocessor. The microprocessor provides the intelligence to the SIC to provide a constant rotation rate and to know the actuator s exact position. The SIC monitors and controls the brushless DC motor s rotation and provides a Digital Rotation Sensing (DRS) function to prevent damage to the actuator in a stall condition. The position feedback signal is generated with out the need for mechanical feedback potentiometers using DRS. The actuator may be stalled anywhere in its normal rotation without the need of mechanical end switches. The is mounted directly to control shafts up to.05 diameter by means of its universal clamp and anti-rotation bracket. crankarm and several mounting brackets are available for damper applications where the actuator cannot be direct coupled to the damper shaft. The actuator provides constant torque to the application with and without power applied to the actuator. The actuator is shipped in a Mid position, compression against seats or gaskets for tight shut-off is accomplished manually. Dimensions [ll numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).05" Centered (Field Selectable) K- US (optional) /" to.05" djustable K US (optional) /8" to /" djustable.0" [7] 8.75" [] 7.5" [9].8" [].90" [].77" [5]." [9] D007 G09-IG-Subject to change. elimo ircontrols (US), Inc.
Proportional damper actuator, non-spring return, Multi-Function Technology Control Signal to 0 VDC to 0 VDC Feedback Signal Standard Wiring lk () Common Wht () Y Input, to 0V Grn (5) U Output, to 0V W0 Control Signal to 0 m Standard Wiring Ω 500Ω / watt to 0 VDC Feedback Signal lk () Common Wht () Y Input, to 0V Grn (5) U Output, to 0V W0 CCW(L) CW(R) CCW(L) CW(R) Control Signal to 0 VDC Open = 0 V Position Closed = Normal Operation Override to zero position lk () Common Wht () Y Input, to 0V Override to zero position lk () Common Ω 500Ω / watt Control Signal to 0 m Wht () Y Input, to 0V Open = m Position Closed = Normal Operation M G09-Subject to change. elimo ircontrols (US), Inc. Control Signal to 0 VDC C Closed = 0 V Position C Closed = Normal Operation Override to 0 V position Ω Control Signal -0 VDC or to 0 m 500Ω / watt C lk () Common Wht () Y Input, to 0V Override control to min, mid, max, positions lk () Common Wht () Y Input, to 0V Functions a b c Min* Mid* Max* Normal** 0% 50% 00% Control mode acc. to Y * Default selectable 0-00%. See Data Sheet. ** Customizable. See Data Sheet. Override to 0 m position lk () Common Ω Control Signal to 0 m Wht () Y Input, to 0V 500Ω C / watt Closed = 0 m Position C Closed = Normal Operation to 0 m Control Signal Notes With a -0 m Input, up to actuators may be wired in parallel. % shift in the signal is seen when using a 500Ω resistor. Power consumption must be observed. Provide overload protection and disconnect as required. ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. S S S NC NO S US uxiliary Switches for ctuator may also be powered by VDC. ZG-R0 may be used. S S S S S5 S NC NO NC NO S US W0 5
Pre-set MFT configurations for DC voltage control, P-000 F-MFT(-S) US in-lb NF-MFT US Non- GM-MFT US 0 in-lb LF-MFT(-S) US 5 in-lb LF-MFT(-S)-0 US 5 in-lb NM-MFT US LM-MFT US 5 in-lb P-000 configuration types are used for VDC control applications. Pre-set configurations are listed which offer solutions for standard control applications. dditional pre-set configurations are listed which offer solutions for non-standard control application for: djustable Start and Stop points Sequencing actuators Combination for master slave Wiring VDC VC/DC Transformer lk () Common 9D5 W00 Control Signal Position Feedback Wht () Y Input Control Motion Diagnostics (larms)* actuators) Range Feedback Time Torque % daptation Feedback Feedback Feedback Feedback P-000.0 to 0.0 VDC.0 to 0.0 VDC 50 00 OFF P-000 0.0 to 0.0 VDC 0.0 to 0.0 VDC 50 00 OFF P-000.0 to 0.0 VDC 0.0 to 5.0 VDC 50 00 OFF P-000.0 to 7.0 VDC.0 to 0.0 VDC 50 00 OFF P-0005.0 to 9.0 VDC.0 to 0.0 VDC 50 00 OFF P-000 0.5 to.5 VDC.0 to 0.0 VDC 50 00 OFF P-0007 0.0 to 5.0 VDC.0 to 0.0 VDC 50 00 OFF P-0008 0.0 to 5.0 VDC 0.0 to 0.0 VDC 50 00 OFF P-0009 5.0 to 0.0 VDC.0 to 0.0 VDC 50 00 OFF P-000 5.0 to 0.0 VDC 0.0 to 0.0 VDC 50 00 OFF P-00 0.0 to 5.0 VDC 0.0 to 5.0 VDC 50 00 ON-Manual 8.5 VDC P-00 0.0 to 5.0 VDC 0.0 to.5 VDC 50 00 ON-Manual 5.5 VDC P-00 0.0 to 0.0 VDC.0 to 0.0 VDC 50 00 OFF P-00 0.0 to 0.0 VDC 0.0 to.5 VDC 00 00 ON-Manual 5.5 VDC P-005.0 to 5.0 VDC.0 to 0.0 VDC 50 00 OFF P-00.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-007.0 to 0.0 VDC.0 to 0.0 VDC 50 00 OFF P-008.0 to 7.0 VDC.0 to 0.0 VDC 50 00 OFF P-009.0 to 0.0 VDC.0 to 0.0 VDC 00 00 OFF P-000 9.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-00.0 to 0.0 VDC 0.0 to 5.0 VDC 50 00 OFF 8.5 VDC 5.5 VDC P-00 0.0 to.9 VDC 0.0 to.9 VDC 50 00 OFF P-00 5. to 0.0 VDC 5. to 0.0 VDC 50 00 OFF P-00 0.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-005.0 to 0.0 VDC.0 to 0.0 VDC 75 00 OFF P-00.0 to 9.0 VDC.0 to 0.0 VDC 50 00 OFF P-007 5.0 to 9.0 VDC.0 to 0.0 VDC 50 00 OFF P-008 0.0 to 0.0 VDC 0.0 to 0.0 VDC 00 00 OFF P-009.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-000.0 to 9.0 VDC.0 to 0.0 VDC 50 00 OFF P-00 0.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-00.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-00.0 to.0 VDC.0 to 0.0 VDC 50 00 OFF P-00.0 to 0.0 VDC.0 to 0.0 VDC 0 00 OFF P-005.0 to 0.0 VDC.0 to 0.0 VDC 78 00 OFF Voltage * Contact elimo if you wish to use any of these functions. **Select ONE Fault and ONE Maintenance larm. The GM-MFT US running time is limited to a range of 0-00 seconds. 8 Pre-set MFT Order Form, page 00 and 0. Custom Order Form on page 0. G09-IG-Subject to change. elimo ircontrols (US), Inc.
Pre-set MFT configurations for pulse width modulation control, P-000 F-MFT (-S) US in-lb NF-MFT US LF-MFT (-S) US 5 in-lb LF-MFT (-S)-0 US 5 in-lb Non- GM-MFT US 0 in-lb NM-MFT US LM-MFT US 5 in-lb P-000 configuration types are used for Pulse Width Modulation control outputs. Most D.D.C. controllers have digital outputs which incorporate a default PWM range. This enables a D.O. to be used as a proportional output when needed. Simply select the appropriate configuration code according to your application. Wiring PWM, triac source and sink (C only) Position Feedback VDC lk () Common Wht () Y Input 9D5 W0 Control signal may be pulsed from either the Hot (Source) or Common (Sink) VC line Position feedback cannot be used with a Triac sink controller. The actuators internal common reference is not compatible. G09-Subject to change. elimo ircontrols (US), Inc. Pulse Width actuators) Control Motion Diagnostics (larms)* Range Feedback Time Torque % daptation Feedback Feedback Feedback Feedback P-000 0.59 to.9 sec..0 to 0.0 VDC 50 00 OFF P-000 0.0 to 5.00 sec..0 to 0.0 VDC 50 00 OFF P-000 0.0 to 5.50 sec..0 to 0.0 VDC 50 00 OFF P-000 0.0 to 5.0 sec..0 to 0.0 VDC 50 00 OFF P-0005 0.0 to 5.0 sec. 0.0 to 5.0 VDC 50 00 OFF P-000 0.59 to.9 sec. 0.0 to 5.0 VDC 50 00 ON-Manual 8.5 VDC P-0007 0.0 to 5.00 sec. 0.0 to 5.0 VDC 50 00 ON-Manual 8.5 VDC P-0008 0.0 to 5.50 sec. 0.0 to 5.0 VDC 50 00 ON-Manual 8.5 VDC P-0009 0.59 to.9 sec. 0.0 to.5 VDC 50 00 ON-Manual 5.5 VDC P-000 0.0 to 5.00 sec. 0.0 to.5 VDC 50 00 ON-Manual 5.5 VDC P-00 0.0 to 5.50 sec. 0.0 to.5 VDC 50 00 ON-Manual 5.5 VDC P-00 0.50 to 5.50 sec. 0.0 to 0.0 VDC 50 00 OFF P-00 0.50 to.9 sec. 0.0 to 5.0 VDC 50 00 OFF P-00 0.0 to 0.00 sec..0 to 0.0 VDC 50 00 OFF MFT * Contact elimo if you wish to use any of these functions. **Select ONE Fault and ONE Maintenance larm. The GM-MFT US running time is limited to a range of 0-00 seconds. Pre-set MFT Order Form, page 00 and 0. Custom Order Form on page 0. 8
Pre-set MFT configurations for floating point control, P-000 F-MFT (-S) US in-lb NF-MFT US LF-MFT (-S) US 5 in-lb LF-MFT (-S)-0 US 5 in-lb P-000 configuration types are used for floating point control outputs. In this application MFT actuators offer constant running time and standard feedback options. IN00 or IN007 diode is required. Wiring Floating Point 9D5 Non- GM-MFT US 0 in-lb NM-MFT US LM-MFT US 5 in-lb Floating Point actuators) (C only) Triac Sink Wiring Hot Controller COM Position Feedback Diode may be placed at the control panel. Reduces field wiring lk () Common 5 Wht () Y Input (C only) Triac Source Wiring Hot Controller COM IN00 or IN007 diode. (IN007 supplied, elimo part number 055) Triac and can also be contact closures. Why is a diode required? The actuator is designed to recognize the rectified voltage as an opposite control signal request. * Contact elimo if you wish to use any of these functions. ** Select ONE Fault and ONE Maintenance larm. The GM-MFT US running time is limited to a range of 0-00 seconds. Position Feedback Position feedback cannot be used with a Triac sink controller. The actuators internal common reference is not compatible. CCW CW Diode may be placed at the control panel. Reduces field wiring lk () Common Wht () Y Input Direction of rotation switch Control Motion Diagnostics (larms)* CCW CW Range Feedback Time Torque % daptation Feedback Feedback Feedback Feedback P-000 Floating point.0 to 0.0 VDC 50 00 OFF P-000 Floating point 0.0 to 0.0 VDC 50 00 OFF P-000 Floating point.0 to 0.0 VDC 00 00 OFF P-000 Floating point 0.0 to 5.0 VDC 00 00 OFF P-0005 Floating point 0.0 to 0.0 VDC 00 00 OFF P-000 Floating point 0.0 to 5.0 VDC 50 00 OFF P-0007 Floating point.0 to 0.0 VDC 00 00 ON-Manual P-0008 Floating point.0 to 0.0 VDC 75 00 OFF P-0009 Floating point.0 to 0.0 VDC 85 00 OFF P-000 Floating point 0.0 to.5 VDC 50 00 ON-Manual W0 5 The Common connection from the actuator must be connected to the Hot Connection of the controller. The actuator Hot must be connected to the control board Common. MFT actuators are compatible with contact closure, triac source and triac sink type contollers. W0 G09-IG-Subject to change. elimo ircontrols (US), Inc. 8 Pre-set MFT Order Form, page 00 and 0. Custom Order Form on page 0.
Pre-set MFT configurations for on/off control, P-000 F-MFT (-S) US in-lb NF-MFT US LF-MFT (-S) US 5 in-lb LF-MFT (-S)-0 US 5 in-lb P-000 configuration types are used for on/off control outputs. The configuration allows for service replacement of on/off actuators when a true on/off actuator is not available. In addition the MFT actuator offers additional functionality in the on/off mode, such as configuration P-000 with minimum position and to 0 VDC feedback. Non- GM-MFT US 0 in-lb NM-MFT US LM-MFT US 5 in-lb Wiring Two Position VC/DC Transformer 9D5 lk () Common Red () Hot W0 Position Feedback VDC a Wht () Y Input G09-Subject to change. elimo ircontrols (US), Inc. On/Off 5 actuators) connected to the Hot Connection of the controller. The actuator Hot must be connected to the control board Common. MFT actuators are compatible with contact closure, triac source and triac sink type contollers. Control Motion Diagnostics (larms)* Range Feedback Time Torque % daptation Feedback Feedback Feedback Feedback P-000 On/Off None 75 00 OFF P-000 On/Off.0 to 0.0 VDC 50 00 OFF P-000 On/Off None 75 00 OFF P-000 On/Off 0.0 to 5.0 VDC 00 00 OFF P-0005 On/Off 0.0 to 0.0 VDC 00 00 OFF MFT * Contact elimo if you wish to use any of these functions. ** Select ONE Fault and ONE Maintenance larm. The GM-MFT US running time is limited to a range of 0-00 seconds. Pre-set MFT Order Form, page 00 and 0. Custom Order Form on page 0. 85