Nerf N-Strike Elite Alpha Trooper CS-12 Hammer Rod Replacement

Size: px

Start display at page:

Download "Nerf N-Strike Elite Alpha Trooper CS-12 Hammer Rod Replacement"

Derrick Howard Bishop
5 years ago
Views:

1 Nerf N-Strike Elite Alpha Trooper CS-12 Hammer Rod Replacement This guide shows you how to replace the silver hammer rod next to the barrel of the Nerf gun. Written By: Elizabeth Coffey ifixit CC BY-NC-SA Page 1 of 12

2 INTRODUCTION A damaged hammer rod may make it difficult, or entirely prevent the slide from operating. This can make loading the rifle difficult. This guide shows you how to access and replace the silver hammer rod next to the barrel of the Nerf gun. TOOLS: Phillips #0 Screwdriver (1) PARTS: Compatible Replacement Spring (1) ifixit CC BY-NC-SA Page 2 of 12

Step 1 Notes Before Starting There are many screws of varying lengths involved in the

It is important to keep track which screws correspond to which holes.

Be sure that the rifle is discharged and unloaded before starting disassembly.

3 Step 1 Notes Before Starting There are many screws of varying lengths involved in the disassembling of this device. It is important to keep track which screws correspond to which holes. This will help ensure proper reassembly. Be sure that the rifle is discharged and unloaded before starting disassembly. Step 2 Rear Cap Removal Looking from the rear of the rifle, remove the two 10 mm phillips screws holding the orange cap to the butt of the rifle. Pull off the orange cap. ifixit CC BY-NC-SA Page 3 of 12

Step 3 Slide Removal With the rifle barrel pointing left,

4 Step 3 Slide Removal With the rifle barrel pointing left, remove the two 8mm phillips screws holding the slide mechanism together. Remove the three 10 mm phillips screws from the bottom of the slide mechanism. Separate and remove the two halves of the slide mechanism. Make sure to keep track of which screws correspond to which holes. ifixit CC BY-NC-SA Page 4 of 12

Remove the two 8 mm phillips screws from the main body.

5 Step 4 Again with the rifle barrel pointing left, remove the fourteen 10 mm phillips screws from the main body of the rifle. Remove the two 5 mm phillips screws from the main body. Remove the two 8 mm phillips screws from the main body. Screws are varying lengths, make sure to keep track of which screws correspond to which holes. ifixit CC BY-NC-SA Page 5 of 12

Step 5 Pull the two halves of the rifle apart.

to gently pry the edges of the body apart.

be easy to lose. Remove the access gate and barrel cover.

6 Step 5 Pull the two halves of the rifle apart. Be careful of the spring at the rear end of the rifle. It may come flying out. If you have difficulty pulling the two halves apart, spudger to gently pry the edges of the body apart. Also be careful of small parts when opening the gun, they may be easy to lose. Remove the access gate and barrel cover. Step 6 Spring Removal You should now be able to pull the main firing spring from the rear of the rifle. ifixit CC BY-NC-SA Page 6 of 12

7 Step 7 Hammer Rod Remove the two 5 mm phillips screws holding the muzzle in place. Step 8 Remove the barrel and muzzle assembly from the gun body. ifixit CC BY-NC-SA Page 7 of 12

8 Step 9 Remove the 5mm phillips screw holding in the chamber lock mechanism. Step 10 Pull the front chamber lock spring up and out of its seat. Pull the front chamber lock mechanism down and out of the rifle barrel. Note there are two pieces to this mechanism. ifixit CC BY-NC-SA Page 8 of 12

9 Step 11 Holding the rear chamber slide lock down, slide the chamber to the rear of the rifle. Remove the rear section of the barrel. Step 12 With the plunger in the air cylinder, pull the plunger lock out of the rifle body. ifixit CC BY-NC-SA Page 9 of 12

Step 14 While holding the slide lock mechanism down, pull the bullet

10 Step 13 Pull the air cylinder and plunger assembly rearwards and out of the rifle. Step 14 While holding the slide lock mechanism down, pull the bullet chamber assembly up and out of the rifle. Part of the magazine lock mechanism should come along with it. ifixit CC BY-NC-SA Page 10 of 12

Step 15 With the hammer rod side of the bullet

11 Step 15 With the hammer rod side of the bullet chamber facing you, unscrew the 5 mm phillips screw holding the hammer rod in place. Step 16 Remove the hammer rod. To reassemble your device, follow these instructions in reverse order. ifixit CC BY-NC-SA Page 11 of 12

12 This document was last generated on :49:21 PM. ifixit CC BY-NC-SA Page 12 of 12

Written By: Marcus C

Cleaning a Browning BPS Shotgun How to clean the Receiver and Barrel of a Browning BPS Shotgun. Written By: Marcus C ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide will take you