Note: The serial number/identification label is located within the equipment compartment and skimmer housing.

Transcription

1 Spa OWNER S MANUAL

2 Model: Serial Number: Date Installed: Dealer: Address: Telephone: Note: The serial number/identification label is located within the equipment compartment and skimmer housing. Model Average Fill Weight Weight Gallons Filled lbs. Empty lbs # Polo # Adelphi # Putnam # Travers # Excelsior # Canfield # Pavilion # Victoria Select Plus Series # Lexington* Plus # Clifton* Plus # Franklin* Plus Thank you for your recent Saratoga Spa Purchase. This owners manual has been designed to acquaint you with your Saratoga Spa s operation and general maintenance. Keep this manual available for future reference. If you have any questions regarding your Saratoga Spa, contact your local dealer. Thank you.

3 Table of Contents SARATOGA SPA SAFETY INSTRUCTIONS Avoiding Risk to Children...2 Avoiding Risk of Electrical Shock...3 Avoiding Risk of Injury...3 Unclean Water... 4 Avoiding Risk of Hyperthermia...4 Avoiding Risk of Skin Burns... 5 Important Spa Instructions...5 LUXURY AND SELECT LINE SPA MODELS Specifications... 6 LUXURY LINE FEATURES AND OPERATIONS Polo...7 Adelphi...8 Putnam...9 Travers Excelsior Canfield Victoria Pavilion SELECT LINE FEATURES AND OPERATIONS Lexington Plus Clifton Plus Franklin Plus INSTALLATION INSTRUCTIONS Location Preparation Outdoor Installation Indoor Installation ELECTRICAL REQUIREMENTS AND PRECAUTIONS 220 Volt Permanently Connect Models Electrical Installation Instructions 220 Volt Models Electrical Spa Wiring Connection Instructions 220 Volt Models /220 Volt Convertible Models Electrical Installation Instructions 110 Volt Models Electrical Spa Wiring Connection Instructions 110 Volt Models INITIAL OPERATING INSTRUCTIONS Start-up and Re-fill Procedures Start-up Procedures Saratoga Spa Jet Identifications Saratoga Spa Jet Selectors JET SYSTEM MENUS Polo Adelphi Putnam Travers Excelsior Canfield Victoria Pavilion Lexington Plus Clifton Plus Franklin Plus EQUIPMENT MAINTENANCE Jet Selector Maintenance Light Bulb Replacement CONTROL PANEL OPERATION Main Panel Temperature Control Conserve Mode Jet Buttons Option Button Light Control Button Optional Color Blast and Color Splash Lighting Main Control Panel Locking Features Major Spa Panel Lock Minor Temperature Lock SPA CARE AND WATER MAINTENANCE General Information Filter Cartridge Removal and Cleaning Care of Pillows Care of Exterior Care of Spa Cover Winterizing Your Spa Water Quality Maintenance TROUBLESHOOTING Troubleshooting Guides Smart Winter Mode Summer Setting Mode Diagnostic Display Messages PARTS AND WARRANTY INFORMATION Service and Warranty Information Replacement Parts Accessories Spa Care and Maintenance Record

4 Saratoga Spa Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS AVOIDING THE RISK TO CHILDREN SPA SAFETY REMINDERS DANGER: RISK OF CHILD DROWNING Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use a spa unless they are supervised at all times. WARNING: To reduce the risk of injury, do not permit children to use this spa unless they are closely supervised at all times. To reduce the risk of injury, lower water temperatures are recommended for young children. Children are especially sensitive to hot water. DO: Make sure you always lock the child resistant spa cover locks after using the spa for your children s safety. Every Saratoga Spa is equipped with a locking cover that meets the ASTM F Standard for Safety Covers. Test the water temperature with your hand before allowing children to enter the spa to be sure that it s comfortable. Children are especially sensitive to hot water. Remind children that wet surfaces can be very slippery. Make sure that children are careful when entering or exiting the spa. DON T: Allow children to climb onto the spa cover. Allow children to have unsupervised access to the spa. DANGER: RISK OF ELECTROCUTION Connect only to a grounded source. Do not bury the power cord. A buried power cord may result in death, or serious personal injury due to electrocution if direct burial-type cable is not used, or if improper digging occurs. A ground terminal (pressure wire connector) is provided on the control box inside the unit to permit connection of a minimum No. 8 AWG (8.4 mm) solid copper bonding conductor between this point and any metal equipment, metal water pipe, metal enclosures of electrical equipment, or conduit within five feet (1.5 m) of the unit as needed to comply with local requirements. To reduce the risk of electrocution, replace all damaged cords immediately. Failure to do so may result in death or serious personal injury due to electrocution. 2

5 DANGER: RISK OF ELECTRIC SHOCK Do not permit any electrical appliance, such as a light, telephone, radio or television within 5 feet (1.5m) of a spa. These units DO NOT have an internal ground fault circuit interrupter. The installation of a ground fault circuit interrupter MUST be done by a qualified Electrician and must meet all local and national codes. Failure to maintain a safe distance may result in death, or serious personal injury due to electrocution, if the appliance should fall into the spa. Install at least 5 feet (1.5 m) from all metal surfaces. A spa may be installed within 5 feet of a metal surface if each metal surface is permanently connected by a minimum No. 8 AWG (8.4 mm) solid copper conductor attached to the wire ground connector on the terminal box that is provided for this purpose if in accordance with National Electrical Code ANSI/ NMFPA Install your spa is such a way that drainage is away from the electrical compartment and from all electrical components. DO: Do test the water temperature with your hand before entering the spa to be sure the water temperature is comfortable. Do keep the spa cover locked when the spa is not in use. Do check the equipment compartment monthly for any signs of tampering to the spa equipment. Do follow the maintenance instructions of the spa found in this owner s manual. Be sure your spa is connected to the power supply correctly - use a licensed electrical contractor. Test the Ground Fault Circuit Interrupter(s) once a month. DON T: Use the spa with the equipment compartment door removed. Place electrical appliances within 5 feet (1.5m) of the spa. Don t allow children to have unsupervised access to the spa. Don t block the equipment compartment vents. This could cause damage to the spa equipment and will void the warranty. DANGER: RISK OF PERSONAL INJURY To reduce the risk of injury to persons, DO NOT remove suction fittings located at the bottom footwells of the spa. The suction fittings in the spa are sized to match the specific water flow created by the pump. Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting. Never operate the spa if the suction fittings are broken or missing. There is a danger of slipping and falling. Remember that wet surfaces can be very slippery. Take care when entering or exiting the spa. People with infectious diseases should not use the spa. Keep any loose articles of clothing or hanging jewelry away from rotating jets or other moving components. The use of drugs, alcohol, or medication before or during spa use may lead to unconsciousness with the possibility of drowning. Persons using medications should consult a physician before using a spa; some medication may cause a user to become drowsy, while other medication may affect heart rate, blood pressure, and circulation. 3

6 Persons taking medications which induce drowsiness, such as tranquilizers, antihistamines or anticoagulants should not use the spa. Water temperature in excess of 38ºC (100.4ºF) may be injurious to your health. Pregnant women should consult a physician before using spa. Persons suffering from obesity, or with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using spa. UNCLEAN WATER Keep the water clean and sanitized with correct chemical care. Maintain water chemistry in accordance with chemical manufacturer s instructions. Important: Turn on Jet Pump #1, on high speed, for a 15 minute cycle after adding ANY spa water chemicals into the spa. Clean the filter cartridges monthly to remove debris and mineral buildup which may affect the performance of the jets, limit the flow, or trip the high limit thermostat. DANGER: RISK OF HYPERTHERMIA The causes, symptoms and effects of hyperthermia may be described as follows: Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6ºF. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting. The effects of hyperthermia include: 1. Failure to perceive heat. 2. Failure to recognize the need to exit the spa or hot tub. 3. Unawareness of impending hazard. 4. Fetal damage in pregnant women. 5. Physical inability to exit the spa or hot tub. 6. Unconsciousness resulting in drowning. WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas. TO REDUCE THE RISK OF INJURY: The water in the spa should never exceed 104 F (40ºC). Water temperatures between 100 F (37.7ºC) and 104 F (40ºC) are considered safe for a healthy adult. Lower water temperatures are recommended for extended use (exceeding ten minutes) and for young children. Extended use can cause hyperthermia. Pregnant or possibly pregnant women should limit spa water temperatures to 100 F. Failure to do so may result in permanent injury to your baby. Do not use spa immediately following strenuous exercise. 4

7 DANGER: AVOIDING THE RISK OF SKIN BURNS To reduce the risk of injury, before entering a spa the user should measure the water temperature with an accurate thermometer, since the tolerance of temperature-regulating devices may vary by as much as ±5 F. Test the water with your hand before entering the spa to be sure it s comfortable. Important: The following contains important spa information, and we strongly encourage you to read and apply them. DO: Use and lock the vinyl cover when the spa is not in use, whether it is empty or full. Follow the Spa Care and Maintenance recommendations stated in this manual. Use only approved accessories and recommended spa chemicals and cleaners. DON T: Leave the Saratoga spa exposed to the sun without water or the cover in place. Exposure to direct sunlight can cause solar distress of the shell material. Lift or drag the vinyl cover by using the cover lock straps; always lift or carry the cover by using the handles. Attempt to open the electrical control box. There are no user serviceable parts inside. Opening of the control box by the spa owner will void the warranty. If you have an operational problem, carefully go through the steps outlined in the Troubleshooting section. If you are not able to resolve the problem, contact your authorized Saratoga Spa dealer. Many problems can easily be diagnosed over the telephone by an Authorized Service Technician. Block or sit on the filter compartment area. Allow excessive weight to be placed on the spa cover. Doing so could damage the spa cover and void any warranty. * SAVE THESE INSTRUCTIONS * 5

8 Luxury Line Spa Specifications Width Height Length Average Dry Average Seating Fill Weight Full Weight Locations Polo gal 385 lbs. 1,609 lbs. 2 1, 45m 0,74m 2,03m 862L 175 kg 731 kg 2 Adelphi gal 400 lbs. 2,358 lbs ,70m 0,74m 2,03m 908L 181 kg 1,071 kg 3-4 Putnam gal 475 lbs. 3,250 lbs ,90m 0,86m 2,13m 1,287L 215 kg 1,474 kg 4-6 Travers gal 525 lbs lbs m 0.85m 2,29m 1,287L 238 kg 1656 kg 4-5 Excelsior gal 630 lbs. 3,160 lbs ,13m 0,91m 2,13m 1,173L 285 kg 1,433 kg 4-5 Canfield gal 580 lbs. 3,640 lbs ,13m 0,91m 2,13m 1,419L 263 kg 1,652 kg 5-6 Victoria gal 800 lbs lbs ,26m 0,96m 2,36m 1987L 363 kg 2306 kg 6-7 Pavilion gal 800 lbs lbs ,26m 0,96m 2,36m 1987L 363 kg 2306 kg 6-8 Select Plus Series Specifications Width Height Length Average Dry Average Seating Fill Weight Full Weight Locations Lexington gal 480 lbs lbs. 5 Plus 2,03m 0,86m 2,13m 1324L 218 kg 1516 kg 5 Clifton gal 570 lbs lbs. 6-7 Plus 2,13m 0,91m 2,13m 1419L 260 kg 1647 kg 6-7 Franklin gal 570 lbs lbs. 6-7 Plus 2,26m 0,96m 2,36m 1987L 260 kg 1647 kg 6-7 Important: Saratoga Spa Company suggests a structural engineer or contractor be consulted before the spa is placed on an elevated deck. Note: The Average Full weight of the spa includes only the spa and the water inside the spa. 6

9 Polo 110V/220V - Spa Features A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jet H. Storm Jets I. Vortex Circulation Jet J. Relax Stream Waterfall K. Bottom Spa Drain L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light Polo 110V/220V - Saratoga Spa Operations Center 1. 1 Uni- Speed Hydro Pump 2. 1 kw/4 kw Heater 3. Purity Circulation Pump 4. Convertible Power Pak 110V/220V 5. Whisper Zone Ozonator 6. Drain Valve 7. Bonding Terminal 7

10 Adelphi 110V/220V - Spa Features A. Versa-Flo /CFE Valves B. Roto Stream Valve C. Power Massage Jet D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jets H. Vortex Circulation Jet I. Bottom Spa Drain J. Relax Stream Waterfall K. Backlit Digital Control Panel L.. Microban Filtration M. Toploading Skimmer N. Pillows O. Storm Jets P. Mood Light Adelphi 110V/220V - Saratoga Spa Operations Center 1. 1 Uni Speed Hydro Pump 2. 1 kw/4 kw Heater 3. Purity Circulation Pump 4. Convertible Power Pak 110V/220V 5. Whisper Zone Ozonator 6. Drain valve 7. Mood Light 8. Bonding terminal

11 Putnam 110/220V - Spa Features * 220V Unit Shown With Optional Blower Jets * A. Versa-Flo /CFE Valves B. Roto-Stream Valve C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jets H. Storm Jets I. Vortex Circulation Jet J. Relax Stream Waterfall K. Bottom Spa Drain L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light Putnam 110V/220V or 220V - Saratoga Spa Operations Center 1a. 110V/220V Model - 1 Uni Speed Hydro Pump 1b. 220V Model - 1 Two Speed Hydro Pump 2a. 110V/220V Model - 1 kw/4 kw Heater 2b. 220V Model - 4 kw Heater 3. Purity Circulation Pump 4. Convertible Power Pak 110V/220V for 110V/220V Model, 220V Power Pak for 220 Model 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood Light 8. Bonding Terminal 6 8 * 110V/220V Operations Center Shown * 9

12 Travers - Spa Features * Travers 220V Unit Shown With Optional Blower Jets * A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Storm Jets H. Deluxe Jets I. Vortex Circulation Jet J. Relax Stream Waterfall K. Bottom Spa Drain L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light Travers 110V/220V or 220V - Saratoga Spa Operations Center 1a. 110V/220V Model - 1 Uni Speed Hydro Pump 1b. 220V Model - 1 Dual Speed Hydro Pump 2a. 110V/220V Model - 1 kw/4 kw Heater 2b. 220V Model - 4 kw Heater 3. Purity Circulation Pump 4. Convertible Power Pak 110V/220V for 110V/220V Model, 220V Power Pak for 220V Model 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood Light 8. Bonding Terminal 6 8 * 110V/220V Operations Center Shown *

13 Excelsior - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo / CFE Valves B. Roto Stream Valve C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jets H. Storm Jets I. Vortex Circulation Jet J. Bottom Spa Drain K. Relax Stream Waterfall L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light Excelsior - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 2. 4 kw Heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood Light 8. Bonding Terminal 11

14 Canfield - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo /CFE Valves B. Roto Stream Valve C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jets H. Storm Jets I. Vortex Circulation Jet J. Bottom Spa Drain K. Relax Stream Waterfall L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light 12 Canfield - Saratoga Spa Operations Center 1. (2) Dual Speed Hydro Pumps 2. 4 kw Heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood Light 8. Bonding Terminal

15 Victoria - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jet H. Storm Jets I. Vortex Circulation Jet J. Relax Stream Waterfall K. Bottom Spa Drain L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Turbo Jets Q. Satellite Controls R. Mood Light Victoria - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 1a. 1 Uni Speed Hydro Pump (behind Power Pak) 2. 4 kw heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood light 8. Bonding Terminal 13

16 Pavilion - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo / CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Power Stream Jets E. Cluster Jets F. Mini Jets G. Deluxe Jet H. Storm Jets I. Turbo Jets J. Vortex Circulation Jet K. Relax Stream Waterfall L. Bottom Spa Drain M. Backlit Digital Control Panel N. Microban Filtration O. Toploading Skimmer P. Pillows Q. Mood Light 14 Pavilion - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 1a. 1 Uni Speed Hydro Pump (behind PowerPak) 2. 4 kw heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood light 8. Bonding Terminal

17 SELECT *PLUS* SERIES Lexington *Plus* - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Cluster Jets E. Mini Jets F. Deluxe Jet G. Master Massage H. Vortex Circulation Jet I. Bottom Spa Drain J. Relax Stream Waterfall K. Backlit Digital Control Panel L. Microban Filtration M. Toploading Skimmer N. Pillows O. Mood Light Lexington *Plus* - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 2. 4 kw heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood light 8. Bonding Terminal 15

18 SELECT *PLUS* SERIES Clifton *Plus* - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Cluster Jets E Mini Jets F. Deluxe Jet G. Storm Jets H. Vortex Circulation Jet I. Bottom Spa Drain J. Relax Stream Waterfall K. Backlit Digital Control Panel L. Microban Filtration M. Toploading Skimmer N. Pillows O. Mood Light 16 Clifton *Plus* - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 2. 4 kw heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood light 8. Bonding Terminal

19 SELECT *PLUS* SERIES Franklin *Plus* - Spa Features *Unit Shown With Optional Blower Jets* A. Versa-Flo /CFE Valves B. Roto Stream Valves C. Power Massage Jets D. Cluster Jets E. Mini Jets F. Deluxe Jet G. Storm Jets H. Master Massage I. Vortex Circulation Jet J. Bottom Spa Drain K. Relax Stream Waterfall L. Backlit Digital Control Panel M. Microban Filtration N. Toploading Skimmer O. Pillows P. Mood Light Franklin *Plus* - Saratoga Spa Operations Center 1. 2 Dual Speed Hydro Pumps 2. 4 kw heater 3. Purity Circulation Pump V Power Pak 5. Whisper Zone Ozonator 6. Drain Valve 7. Mood light 8. Bonding Terminal 17

20 Installation Instructions Location Pr eparation Your Saratoga Spa is totally self-contained and portable. You can install the spa outside or inside. Preferable places are on a patio, deck or indoors. The spa should always be placed on a structurally strong, level surface. Other items you need to consider are the following: Verify that the location chosen can support the weight of the spa, the water of the spa and its occupants. Always check the surface of the site to see if it is level before filling the spa with water. Allow access to the equipment compartment for routine maintenance. When positioning the spa, be sure to allow for drainage away from the electrical compartment. Leave easy access to the GFCI breaker. WARNING: The Saratoga Spa is manufactured to be a portable unit. Any permanent installation of this product is done at the risk of the owner. Permanent installation of this unit violates warranty coverage. Outdo or Installation Always keep in mind what type of climate you live in. In a climate with cold, snowy winters you may want to consider locating the spa close to the house for easy access. In climates where it is normally warm or hot year-round, it would be recommended to place the spa in a shaded or cool area. With deck installations it is recommended that a qualified building contractor or structural engineer review the weight the deck can support. The spa specification sheet (on page 6) can assist you with the weights and dimensions of your spa. Indo or Installation Special requirements are needed for indoor installation. Spas normally produce moisture. A ventilation system needs to be considered. Your spa area should contain moisture resistant wall/floor coverings and building materials to avoid damage from moisture over time. Proper drainage of the spas water also needs to be considered. Important: Your Saratoga Spa is equipped with air vents to allow for circulation of air throughout the equipment compartment. These vents are found on the face of the equipment compartment panel and under the corners of the spa at the equipment compartment end. Do not allow vents to be blocked as to prevent the circulation of air in the equipment compartment. YOUR SARATOGA SPA DEALER CAN HELP YOU WITH INFORMATION SUCH AS LOCAL ZONING REGULATIONS AND BUILDING CODES. 18

21 Electrical Requir ements and Pr ecautions: Your Saratoga Spa has gone through numerous tests to verify that all the spas functions operate. Beyond the tests, your Saratoga Spa has been designed to provide the maximum safety against electrical shock. Read and follow the electrical installation requirements and instructions completely. The next few pages will assist you in properly connecting the electrical input. Follow the electrical instructions for your specific spa model. Serious risks or injuries may occur if the spa is improperly wired. 220 Volt Permanently Connected Models: -Polo -Adelphi -Putnam -Travers -Excelsior -Canfield -Victoria -Pavilion -Lexington *Plus* -Clifton *Plus* -Franklin *Plus* SARATOGA SPAS MUST BE WIRED IN ACCORDANCE WITH ALL APPLICABLE LOCAL ELECTRICAL CODES. ALL ELECTRICAL WORK SHOULD BE DONE BY AN EXPERIENCED, LICENSED ELECTRICIAN. WE RECOMMEND THE USE OF APPROPRIATE ELECTRICAL CONDUIT, FITTINGS AND WIRE FOR ALL CIRCUITS. 220 Volt installations require a 60Hz, single phase, three-wire electrical service plus ground (Line 1, Line 2, Neutral and Ground) and must be connected using a minimum supply conductor ampacity of 50 AMPs and a minimum circuit breaker size of 50 AMPs. Note: Use copper wire only (3 wire with ground. 8 gauge under 50', 6 gauge over 50') 220 volt model spas must be connected to a dedicated 220 volt 50 Amp grounded circuit. The term dedicated means the electrical circuit is not being used for any other electrical items (lights, appliances, etc.). If the spa is connected to a non-dedicated circuit, overloading will occur and nuisance tripping of the GFCI breaker switch at the house breaker panel will occur. A ground lug connector is provided on the exterior surface of the spa pack (operations center) inside the equipment compartment. This is to permit the connection of a bonding wire between this point and any metal equipment, enclosures, pipe or conduit within five feet (1.5m) of the spa. This bonding wire must be at least 8AWG solid copper wire. Important: Use only approved pressure-type wire splicing lugs or connectors suitable for the size and type of wiring used! Electrical Installation Instructions for 220 Volt Models 1.To connect the electrical service, first remove the screws from the equipment compartment door. Carefully remove the access panel. 2.Locate the blue M-Class spa control box. Loosen the screws on the front of the control box. Remove the screws and the control box cover. 3.Input the electrical service from the GFCI breaker into the spa equipment compartment. 19

22 Note: The GFCI breaker must be placed in sight of the spa, at a minimum distance of five feet (1.5m) away. Note: As of January 1, 1996 the National Electric Code (NEC) requires GFCI (Ground Fault Circuit Interrupter) on all spa installations. 4. Connect the supply conduit to the blue M-Class spa control box. Factory Installed Neutral (Pigtail) Incoming Ground (Green) Incoming Power (Black) Bottom View of Breaker Power to Spa Neutral to Spa Factory Installed Neutral (Pigtail) Ground to Spa Outgoing Power to Spa Outgoing Neutral to Spa Incoming Power (Black or Red) Incoming Neutral (White) Electrical Spa Wiring Connection Instructions Wiring Connections 20 Important: Never, under any circumstances, should you connect power to the neutral terminal. 1. Identify the TB-1 terminal block, located inside the blue M-Class control box on the left side. 2. Connect the 8 AWG, BLACK wire, from the GFCI 50 amp breaker, terminal L1 to TB-1, Line Connect the 8 AWG, WHITE wire, from the GFCI 50 amp breaker, terminal N to TB-1, neutral. 4. Connect the 8 AWG, GROUND wire, from the GFCI 50 amp breaker, terminal GND (ground) to TB-1, ground. 5. Connect the 8 AWG, RED wire, from the GFCI 50 amp breaker, terminal L2 to TB-1, Line At least two additional lugs marked Bonding Lugs are provided on the external surface of one of the bonded components metal enclosures. To reduce the risk of electrical shock, connect the local common bonding grid in the area of the hot tub or spa to these terminals with an insulated or bare copper conductor not smaller than No. 6 AWG. 7. All field-installed metal components such as rail, ladders, drains or other similar hardware within 10 ft (3m) of the spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than No. 6 AWG. 8. Replace the control box cover and securely tighten the fastening screws. Close and secure the equipment compartment panel. Note: Always use copper wire only (3 wire with ground. 8 gauge under 50ft, 6 gauge over 50ft) The electrical supply for this product must include a suitable rated switch or circuit breaker to open all ungrounded supply conductors to comply with Section of the National Electrical Code ANSI/NEPA The disconnecting means must be readily accessible to the tub occupant but installed at least 5 feet (1.5m) from tub water.

23 110 / 220 Volt Convertible Models - Polo - Putnam Adelphi - Travers Volt Electrical Requirements: The above models are manufactured with the SC-MP 110V/220V convertible spa pack. The units are factory wired for 220 Volt applications and come equipped with a 4KW heater. The models can be converted for 110 Volt applications and to run with a 1KW heater. The 110 Volt models must be connected to a dedicated 110 Volt 20Amp grounded circuit. The term dedicated means the electrical circuit is not being used for any other electrical items (lights, appliances, etc.). If the spa is connected to a non-dedicated circuit, overloading will occur and nuisance tripping of the GFCI breaker switch at the house breaker panel or GFCI cord will occur. Never connect the spa to an extension cord. The 110 Volt models may be optionally equipped with a GFCI power cord (approximately 13 feet long). These models must be plugged into a grounding type, 110 Volt 20Amp receptacle as shown below. No other electrical appliances or fixtures should be used on this circuit. Correct DEDICATED 110V, 20A RECEPTACLE Data label amperage rating of 16 Amps must use this type of 20 Amp dedicated receptacle and plug. Incorrect DEDICATED 110V, 15A RECEPTACLE DO NOT USE THIS TYPE WARNING: The use of any other receptacle or the connection of the plug to a 220 Volt service may cause the spa pack to operate improperly, create the potential for an electrical hazard and may void the spas warranty. Saratoga Spa models must be wired in accordance with all local electrical codes. All electrical work should be done by an experienced, licensed electrician familiar with spa installations. Note: As of January 1, 1996 the National Electrical Code (NEC) requires a GFCI (Ground Fault Circuit Interrupter) on all spa installations. Installation Instructions: The following instructions are for the conversion of the SC-MP 110V/220V control pack from a 220 Volt application to a 110 Volt application. Important: Use only approved pressure-type wire splicing lugs or connectors suitable for the size and type of wiring used. 21

24 Before servicing the spa, make sure all power to the spa is disconnected. Follow the following instructions for a successful electrical installation. 1. Unscrew the screws on the front access panel. 2. Carefully pull access panel towards you (away from spa) and pull upward. Set access panel aside. 3. Locate the blue SC-MP 110V/220V spa control box. Loosen the screws on the front of the control box. Lift the control box cover upward and the terminal block will be exposed. 4. Route the GFCI power cord through the vent hole in the base of the equipment compartment and out from under the corner of the spa. NOTE: 110 Volt installations require a 60Hz, single phase, two-wire electrical service plus ground (Line 1, Neutral and Ground) and must be connected using a minimum supply conductor ampacity of 20Amps and a minimum GFCI circuit breaker size of 20Amps. 5. Input the GFCI power cord to the terminal block inside the spa pack. 6. Connect the #8 AWG black wire, from the power cord, to Line 1 on the input terminal block. 7. Connect the #8 AWG ground wire, from the power cord, to the GND (ground) on the input terminal block. 8. Connect the #8 AWG white wire, from the power cord, to the neutral on the input terminal block. 9. Place a jumper cable between the neutral and Line 2 at the input terminal block. 10. Locate Jumper #1 on the PC board (see wiring diagram) and move Jumper #1 to the right position (low current mode). 11. Close spa pack cover and re-tighten screws. 22

25 Initial Operating Instructions: Start-Up and Refill Pr ocedures Your Saratoga Spa has been tested at the manufacturing plant to ensure that all the spas functions operate. During the test procedure, a small amount of water may have remained in the spas plumbing. Through the shipping process water may have spotted the spas shell. You may need to wipe down the shell with a soft cloth. Please read and follow the start-up instructions to ensure a successful start-up or refill. Important: Inspect and clean spa shell of any debris Do not turn power on to spa unless filled with water to appropriate level (See Page 24). The spa pack must never be operated without water in the spa; serious damage to the heater and/or pump(s) may result. Do not fill spa with water before checking the items below (below items may become loose in transit): A A a) Hand tighten unions at the pumps b) Tighten drain valve Note: Drain Valve is left open for shipping - drain valve must be closed before filling spa. C c) Tighten unions on heater C Do not fill spa with hot water. This may cause a false error code to the high limit sensor. 23

26 Start-up Pr ocedures 1. For a successful start-up, fill the spa with water through the Whisper Clean cartridge. The Whisper Clean cartridge is the cartridge with the coarse threaded yellow ACME style adapter. a. Locate the filter compartment area. Note: Pavilion and Victoria models have three filters, all other models use only two filters. b. Pull up and remove filter cover. c. Remove the filter cartridge and screen adapter by turning them counter clockwise. d. After removing the filter cartridge and screen adapter, place a garden hose through the filter opening. e. At this point, open the air bleeder valve(s) in your filter compartment by turning counter clockwise. f. Turn water on and run water until it reaches a minimum level of 2 above the top of the filters. Note: Besides filling the spa to 2 above the top of the filter, all models will need to be filled to 2 above the highest jet(s) in the spa. This is the minimum level allowed to run the Whisper Clean circulation system. Note: When using a mineral cartridge system, please refer to your dealer for specific instructions on installation. 2. Check all plumbing (clamps, unions and drain valve) connections for leaks. 3. Re-install filter cartridges and screen adapters by turning them clockwise. Exit garden hose from the spa. 24

27 4. At this point, turn power on to the spa control system by turning on the GFCI breaker. The MSPA operations center will begin heating the spa to the factory set temperature of 95ºF (35ºC). 5. The next step is to check that the jet system(s) are operational. Press on the Jet(s) button to turn on the pump(s). A strong force of water flowing through the jets indicates the pump(s) are primed. Weak or surging jet(s) indicates the pump(s) still need to be primed (see Troubleshooting section). 6. Once pump(s) are primed, close the air bleeder valve(s) in the filter compartment. Note: Water will be exiting from the air bleeder valves. 7. Re-install filter cover and allow spa to heat to desired set temperature; this normally takes 24 hours. 110 Volt models may take up to 48 hours to reach desired set temperature hours after initial start-up the spa will go through its first power filtration cycle. Jets 2 (pump 2), Jets 3 (pump 3) and optional Blower will run on high speed for one (1) minute. Then Jet 1 (pump 1) will turn on and run on low speed for one (1) minute. This power filtration cycle is repeated every 24 hours at the exact time as initial power-up. Note: If water bubbles are not coming out of the Whisper Clean Jet/bottom drain, the system is air locked. Refer to the Trouble Shooting Section on page 55 for further instructions. Note: It is recommended to press and release the ground fault circuit interrupter (GFCI) RESET button monthly to verify GFCI is working properly. Note: If power is interrupted, and the conserve filtration cycle has been activated, it will be reset to the continuous 24 hour cycle. 9. Water must be balanced and shocked upon start-up. See your dealer or pages of this manual for details. This procedure must be repeated each time the spa is drained and refilled. 10. The Whisper Clean Jet The combination of the Whisper Clean and Vortex Jet return systems help the Whisper Clean System circulate water from the surface and bottom level of the spa. The Whisper Clean Jet also induces temperature controlled water and ozone into the spas footwell area 24 hours a day. Note: A slow or non-moving Whisper Clean Jet may indicate that the filter cartridge pores are obstructed with dirt, body oils or calcification. Follow the filter cartridge cleaning procedures in this manual (See page 48). Whisper Clean Jet 25

28 Versa-Flo Jets and CFE Jet Descriptions Power Massage Plus Patented jet provides dual water massage to your neck or back from under the built-in headrest. The jet is controlled by a small selector valve, giving the bather total control. Power Stream Underwater jet patterned after the Power Massage. This jet runs a ribbon of water parallel to the surface of the spa body. Not found in all units. Cluster Jet The Cluster Jet provides a concentrated stream of water and air for precise pressure point areas. Mini Swirl Jet The Mini Swirl Jet has an adjustable eyeball for directional or rotational use. To change from directional to rotational, with finger, simply adjust inner nozzle to the rotating position. Cyclo Swirl Jet A larger version of the Mini Swirl Jet, this jet gives a mid-size rotational massage and pulsating massage. To change from directional to rotational, with finger, simply adjust inner nozzle to the rotating position. 26

29 Cyclo Flo Jet This jet provides a balanced mix of air and water to give a soft, powerful, direct pressure massage to mid-size muscle groups. The design allows for higher GPM for performance and maximum relief. Twin Rotational Jet This jet provides multiple adjustment for varied rotational intensities. Turbo Jet Provides an intense lower body massage and whirlpool stimulation through a large orifice. Xtr eme Flo Jet The Xtreme Flo jet provides a mix of water and air. To change from a straight stream to directional, with finger, move inner nozzle to position desired. Gatling Jet A rotating dual nozzle, diffused by seven holes, creates a pulsating body massage. Veri Massage Jet Multiple pressure point flow, provides foot and large muscle relief. 27

30 Saratoga Spa Jet Selectors The Jets in the Saratoga Spa Luxury Line have different ways to adjust the jet therapy systems. While having the Hydro Jet pump(s) on the user has the ability to turn on and off each individual Versa-Flo Jet. The Versa Flo Jet(s) can be turned on and off by turning the outer scallop on the face of the jet. In addition to having the ability to control each individual jet, the jets can be adjusted by zones. Saratoga Spa uses three different ways to adjust the jet therapy zones. The Roto Stream Valves, Versa-Flo Selectors, and CFE Selectors give the user the ability to control the different Jet Therapy Zones. The following pages will discuss the different jet therapy zones found in the Luxury Line Spas and Select Plus Systems. CFE Selector Versa-Flo or CFE Selector Versa-Flo Selector Roto Stream Selector Roto Stream Selector 28

31 Jet Therapy Zones This example will help you to understand the following pages that discuss the jet system menus. The navigational tool was read from standing outside of the spa and in front of the particular selector. Keep this in mind when the following pages discuss 12,3,6 or 9 o clock position settings. The Versa-Flo selector, and CFE selector can only be rotated 180º. The Roto Stream valve can be rotated 360º

32 Polo Jet System Menu A 2A 1 2 2B 1- CFE SELECTOR Controls the Power Massage Jet 1A By turning the CFE selector to the 9, 12 or 3 o clock position the different settings in the Power Massage Plus Jet 1A will turn on. 2 - VERSA-FLO SELECTOR The 3 o clock position activates the jets in the lounge seat 2B. Setting the Versa-Flo Selector to the 9 o clock position turns on the two Power Stream jets and the one Versa-Flo Jet in the footwell area 3A A 3B 4A 4B 4C 3 - CFE SELECTOR The 9 o clock position activates the Power Massage Jet 3A. Turning the small CFE selector to the 3 o clock setting turns on the Relax Stream 3B. 4 - THE ROTO STREAM VALVE Controls the entire seat and footwell area, 4A, 4B, and 4C. Adjusting the Roto Stream valve to different positions will allow different jets to be activated in 4A, 4B, and 4C. 30

33 Adelphi Jet System Menu A 1 2A 2 1- CFE SELECTOR Controls the amount of water flowing through the Power Massage Jet 1A. By setting the CFE selector to the 12 o clock or 6 o clock position the Power Massage Jet 1A is turned on. Setting the CFE selector to the 9 o clock position turns off the Power Massage Jet 1A. 2 - ROTO STREAM VALVE Controls the 6 jets in seat 2A. Adjusting the Roto Stream valve to different settings allows for certain jets to come on in seat 2A. 3A 3 3B 4 4B 4A 3 - VERSA-FLO SELECTOR The small Versa-Flo selector in the 12 o clock position turns on the jets in seat 3A. Versa-Flo selector in the 6 o clock position turns on the Relax Stream 3B. 4 - VERSA-FLO SELECTOR Positioning the small Versa-Flo selector in the 12 o clock position turns on the jets in seat 4B. Pointing the Versa-Flo selector to the 6 o clock position turns on the Power Massage jet behind pillow 4A. 31

34 Putnam Jet System Menu B 2A 1A 2 1 JET 1 HYDRO PUMP ACTIVITIES All Jets in Spa 1 - ROTO STREAM VALVE The Roto Stream valve controls the six Versa- Flo Jets 1A. 2 - CFE SELECTOR Small CFE selector allows the user to adjust the Power Massage Jet 2A or the Relax Stream 2B. 4A 4 3 3A 4B CFE SELECTOR By adjusting the small CFE selector the user is able to adjust the amount of water flowing through the Power Massage Jet 3A. Small CFE selector is able to be positioned from 12, 3 or 6 o clock position. * 220 unit shown 4 -THE VERSA-FLO SELECTOR Controls the jets in zone 4. By turning the Versa-Flo selector to the 12 o clock position the jets in zone 4A will turn on. Positioning the Versa-Flo selector to the 6 o clock position allows the jets in zone 4B to turn on. Versa-Flo selector in 3 o clock position turns on both seats (jets).

35 Travers Jet System Menu A 2 2A 1 3A 3 1B JET 1 HYDRO PUMP ACTIVATES ALL JETS IN SPA 1 - THE CFE SELECTOR Controls the Power Massage Jet 1A and the Relax Stream 1B. Pointing the CFE selector to the 12 o clock position turns on the Power Massage Jet 1A. Pointing the CFE selector to the 6 o clock position will activate the Relax Stream 1B. 2 - THE ROTO STREAM VALVE Controls the jets in seat 2A. 3 - THE SECONDARY ROTO STREAM VALVE Controls the jets in seat 3A. By adjusting each Roto Stream valve to different positions it allows different jets to come on in each seat 2A and 3A. 4A A 5A 4 - THE THIRD ROTO STREAM VALVE Controls the jets in seat 4A. 5 - THE FOURTH ROTO STREAM VALVE Controls the jets in seat 5A. By turning each Roto Stream valve to different positions, it allows different jets to come on in each seat, 4A and 5A. 6 - THE CFE SELECTOR Turns the Power Massage Jet 6A on and off. Adjusting the CFE selector to the 3 o clock or 9 o clock position turns on the Power Massage Jet 6A. Pointing the selector to the 12 o clock position turns off the Power Massage Jet 6A. * 220 unit shown 33

36 Excelsior Jet System Menu A 2B 2C 1 1A 1B 2 2D 2E 1 - CFE SELECTOR Controls the Power Massage Jet 1A and the Relax Stream 1B. Positioning the CFE selector to the 12 o clock position turns on the Power Massage Jet 1A. Pointing the CFE selector to the 6 o clock position turns on the Relax Stream 1B. 2 - VERSA-FLO SELECTOR 12 o clock setting turns off the CFE jets, 2B and 2C. 3 o clock position turns off the wall jet 2E(but leaves all other jets on). 6 o clock position turns on jets in calf area 2B and turns off the jets in seat 2A A 4A 5A ROTO STREAM VALVE Controls the jets in seat 3A. The rotating of the Roto Stream valve allows the user to select the sequence best for them. 4 - CFE SELECTOR 6 o clock position turns off the Power Massage Jet 4A. 9 o clock or 3 o clock positioning will turn on the Power Massage Jet 4A. 5 - VERSA-FLO SELECTOR Allows you to control the jets in seat 5A. 3 o clock positioning turns on the jets in seat 5A. 9 o clock positioning turns off the jets in seat 5A. 34

37 Canfield Jet System Menu C 1 1B 1A 2 2B 2A 1 - VERSA-FLO SELECTOR VALVE Versa-Flo selector valve controls the jets in the lounge seat 1A and bucket seat 1C. 6 o clock position controls the seven jets in the lounge seat 1A and four Power Stream Jets 1B. 12 o clock jets position turns on all jets in zone 1, except for the four Power Stream Jets 1A. 2 - CFE SELECTOR CFE selector controls the Power Massage Jet 2A and Relax Stream 2B. CFE selector on 6 o clock position controls Relax Stream 2B. CFE selector on 12 o clock position activates Power Massage Jet 2A. 4A 5A 4 5 3A VERSA-FLO SELECTOR VALVE Controls bucket seat 3A. 9 o clock position turns off jets in seat 3A. 3 o clock position turns on jets in seat 3A. 4 - ROTO STREAM VALVE Controls the six Versa-Flo Jets 4A. Controls six jets in valve seat 4A at different levels depending on setting. 5 - CFE SELECTOR Allows control of Power Massage Jet 5A. 12 o clock position turns on Power Massage Jet 5A. 6 o clock adjustment turns off Power Massage Jet 5A. 35

38 Victoria Jet System Menu A 1A 1B 1C 1D 1E VERSA-FLO SELECTOR Turning the Versa-Flo selector to the 9 o clock position will turn on the jets in the lounge seat 1E and the bucket seat 1A. The lounge foot jets 1B and all six Power Stream Jets,1C and 1D will be off. Pointing the Versa-Flo selector to the 12 o clock position turns on all the jets in zone 1, 1A,1B, and 1E. Adjusting the Versa-Flo selector to the 3 o clock position turns off the jets in the lounge seat, 1B and 1E. 2 - CFE SELECTOR The small CFE selector controls the Relax Stream 2A. Setting the CFE selector to the 9 o clock position activates the Relax Stream 2A. The 3 o clock setting turns off the Relax Stream 2A. 3A 4A SECONDARY CFE SELECTOR Controls the middle Power Massage Jet 3A. 9 o clock or 3 o clock position will activate the jet. Adjusting the CFE selector to the 12 o clock position turns off the Power Massage Jet 3A. 4 - THIRD CFE SELECTOR The third CFE selector controls the other two Power Massage Jets 4A. Pointing the CFE selector to the 9 o clock setting turns on the two Power Massage Jets 4A. Placing the CFE selector to the 3 o clock position turns off both Power Massage Jets 4A. 36

39 Victoria Jet System Menu A 6A 5 - ROTO STREAM VALVE Controls seat 5A. The turning of the Roto Stream valve allows the user to select which sequence is best for them. 6 - CFE SELECTOR Controls the Power Massage Jet 6A. Setting the CFE selector to the 3 o clock position turns off the Power Massage Jet 6A. The 9 o clock position activates the Power Massage Jet 6A A 8A 8B 7 - VERSA-FLO SELECTOR Controls the jets in seat 7A. The moving of the Versa-Flo selector from left to right turns jets in seat 7A on and off. 8 - VERSA-FLO SELECTOR The 3 o clock position will activate the two wall jets 8A. The footwell jet will be off 8B. The 9 o clock setting will activate the footwell jet 8B and will turn off the two wall jets 8A. 37

40 Pavilion Jet System Menu A 2 3 3A 1A ROTO STREAM VALVE Controls jets in seat 1A. By rotating the Roto Stream valve allows the user to select the sequence best for them. 3 - CFE SELECTOR controls two of the Power Massage Jets 3A. 2 - ROTO STREAM VALVE Seat 2A is controlled in the same manner as seat 1A, by using the Roto Stream valve A 7 6A 7A 5A SECONDARY CFE SELECTOR Controls the third Power Massage Jet 4A. 5 - THIRD CFE SELECTOR The third CFE selector allows you to control one of the two Relax Streams 5A. By positioning the CFE selectors in the 3, 6, or 9 o clock positions it gives the user the ability to turn on or off the jets discussed above, 4A and 5A. 6 - CFE SELECTOR The small CFE selector allows for control of the second Relax Stream 6A. 7 - SECOND CFE SELECTOR Controls one of the three Power Massage Jets 7A.

41 Pavilion Jet System Menu A 8 9A THIRD CFE SELECTOR The third small CFE selector allows for adjustment of the other two Power Massage Jets 8A. 9 - ROTO STREAM VALVE The Roto Stream valve controls the jets in seat 9A. Rotating the Roto Stream valve allows the user to select the sequence best for them. 11A 10A B 10 - VERSA-FLO SELECTOR Pointing the large Versa-Flo selector in the 9 o clock position turns off the jets in seat 10A. Positioning the Versa-Flo selector in the 3 o clock position turns on the jets in seat 10A VERSA-FLO SELECTOR The large Versa-Flo selector controls the sidewall 11A, and footwell jets 11B. Turning the selector to the 12 o clock position activates jets in footwell area 11B. Selector in 6 o clock position turns on jets on side wall 11A. 39

42 Lexington Plus Jet System Menu A 1 1A 2 3B 3A 1 - ROTO STREAM Controls the jets in seat 1A. The adjusting of the Roto Stream valve allows the user to select which sequence is best for them. 2 - CFE SELECTOR Setting the small CFE selector to the 12 o clock position or 6 o clock position will turn on the Power Massage Jet 2A. Placing the CFE selector to the 3 o clock position turns off the Power Massage Jet 2A. 3 - VERSA-FLO SELECTOR Controls seat 3B and the large Master Massage jet 3A. The 9 o clock position will turn on the jet in the footwell 3A and will turn off jets in seat 3B. The 6 o clock position turns on both, seat jets and the jet in the footwell 3A. The 3 o clock setting turns on seat 3B and turns off the jet in the footwell 3A. 5B 4A 4B 4A 4 4B 5 5A VERSA-FLO SELECTOR Controls the jets in the lounge seat. The 9 o clock setting activates the jets in zones 4A. The jets in zone 4B will be turned off. Adjusting the large Versa-Flo selector to the 3 o clock position activates the jets in zones 4B. The jets in zones 4A will be turned off. 5 - CFE SELECTOR The 9 o clock position turns on the Relax Stream 5B and turns off the Power Massage Jet 5A. The 12 o clock setting turns off both the Power Massage Jet 5A and the Relax Stream 5B. Adjusting the CFE selector to the 3 o clock position will activate the Power Massage Jet 5A, and turn off the Relax Stream 5B.

43 Clifton Plus Jet System Menu A 1B 2 2A 3 3A 1 - VERSA-FLO SELECTOR Controls the jets in zone 1A and 1B. The 6 o clock position will turn on the jets in seat 1A. At the same time the jets in sections 1B will be off. Positioning the Versa-Flo selector to the 12 o clock will turn on the jets in section 1B. The jets in seat 1A will turn off CFE SELECTOR Controls the amount of water flowing through the Power Massage Jet 2A. The 3 o clock position will turn off the Power Massage Jet 2A. The 12 or 6 o clock position will turn on the Power Massage Jet 2A. 3 - ROTO STREAM Controls the jets in seat 3A. The turning of the Roto Stream valve allows the user to select which sequence is best for them. 5A 4A 4B 5B CFE SELECTOR Controls the Power Massage Jet 4A and the Relax Stream 4B. Turning the CFE selector to the 3 o clock position activates the Relax Stream 4B, turning the Power Massage Jet 4A off. Setting the CFE selector to the 9 o clock setting will turn on the Power Massage Jet 4A and turn off the Relax Stream 4B. 5 - VERSA-FLO SELECTOR The large Versa-Flo selector 5 in the 12 o clock position will turn on the jets in the seat 5A and turn off the jets in the footwell 5B. Large Versa-Flo selector in 6 o clock position turns off the jets in the seat 5A, while the footwell jets 5B will be on. 41

44 Franklin Plus Jet System Menu B 1 1A 1B 2 2A 1 - CFE SELECTOR Controls the Power Massage Jet 1A and Relax Stream 1B. Pointing CFE selector to the 12 o clock position turns on the Power Massage Jet 1A. Turning the CFE selector to the 6 o clock position activates the Relax Stream 1B. 2 - VERSA-FLO SELECTOR The large Versa-Flo selector is used to turn on the jets in the seat 2Aand the jet in the footwell section 2B. By turning the Versa-Flo selector to the 12 o clock position the jets in the seat 2A will be off. The jet in the footwell 2B will be turned on. Positioning the Versa-Flo 2B selector to the 6 o clock position will turn on the jets in the seat 2A and will turn off the jet 2B in the footwell. 3A 3 4 4A 3 - ROTO STREAM VALVE The Roto Stream valve controls the jets in seat 3A. By positioning the Roto Stream valve allows the user to select which sequence is best for them. 4 - CFE SELECTOR The small CFE selector allows for control of the Power Massage Jet 4A. Setting the CFE selector to the 3 or 9 o clock position will turn on the Power Massage Jet 4A. Pointing the CFE selector to the 12 o clock position will turn off the Power Massage Jet 4A. 42

45 Equipment Maintenance Saratoga Spa Jet Selector Maintenance After a period of time it may become difficult to adjust and rotate the valves. It is necessary to clean the valves to ensure that they continue to perform well. The following instructions will walk you through the steps. 1. Turn power off to the spa. 2. Un-thread valve cover by turning valve cover counter clockwise. 3. Remove complete valve assembly, by pulling outward. 4. Clean or remove debris from valve or diverter. 5. Re-assemble and re-thread valve cover. Replacing the Spa s Light Bulb The spa s light bulb is located inside of the equipment compartment. Remove the front access panel, by first removing the screws on the access panel. Then locate the light housing mounted to the spa shell. Grasp the bulb holder on the back of the light niche. Turn bulb holder counter clockwise to release it from the light niche. Pull bulb out of receptacle and replace it with a new GE 912 bulb. Re-attach the light bulb holder to the light niche by turning the light bulb holder clockwise. Note: Colored lenses for the underwater mood light are an option. 43

46 Contr ol Panel Functions Main Contr ol Panel The panel/topside will indicate the operations of the hydro jet pump(s), air blower, spa light, water temperature and will display diagnostic symbols. Saratoga Spa models are equipped with a main control panel located on the top collar of the spa. The main control panel controls all of the spa functions. It displays the spa s status and any error messages. The main control panel and digital display are illuminated by a light from the inside of the panel. The Victoria model has an additional satellite panel located across from the main control panel that allows the spa user to operate the jets and blower from the other side of the spa. Main Contr ol Panel Buttons and Digital Display The main control panel has buttons which the spa user presses to set the temperature, vary the intensity of the light and activate or deactivate the hydro jet pump(s). The control panel also has a digital display that displays the spas diagnostics (ie-temperature setting, jet functions or error messages). TEMPERATURE CONTROL The set temperature range is from 59ºF (15ºC) to 104ºF (40ºC). The set temperature of the spa water will automatically be 95ºF (35ºC) the first time that power is applied. This is the setting programmed at the factory. If power is disconnected from the spa, it will automatically revert to the last set temperature when power is reapplied. To display the set temperature of the spa, press the Cool or Warm button once. The set temperature will be displayed unless the control panel is locked. To increase the set temperature of the spa water, press the Warm button twice. Pressing the button once will display the current set temperature. Pressing the button again will increase the set temperature by one degree. To decrease the set temperature of the spa water, press the cool button twice. Pressing the button once will display the current set temperature. Pressing the button again will decrease the set temperature by one degree. Note: The temperature shown on the display without pressing on any of the temperature buttons reflects the temperature of the water at that particular moment. CONSERVE BUTTON The Conserve button gives the user the ability to program the number of hours the spa filters. Your Saratoga Spa is factory programmed to filter 24 hours a day. By using the 44

47 Conserve button, the filtering cycles can be adjusted. Each filtration cycle setting will run twice in a 24 hour period. The filtration cycles can be adjusted from 0 to 12 (0 equals no filtering and 12 equals 24 hour filtering). To program the filtering cycles, press and hold the Conserve button until the topside window displays a two-digit number. Release the Conserve button and then use the warm or cool button(s) to reach the desired setting. Once the desired setting has been displayed in the topside window, press the Conserve button to confirm the setting. At that time the new filtration cycle will begin. Note: Saratoga Spa does not recommend setting the filtration cycle to zero (0). Nonfiltered water can create odors, become cloudy, and also be generally unhealthy. Operating the Hydr o Pumps JETS 1 BUTTON Activates the hydro jet pump for maximum hydrotherapy jet action. Press Jets 1 button once for low speed (Jets 1 triangle icon will flash). Press Jets 1 button again for high speed and again to turn off (Jets 1 triangle icon will stay solid when Jets 1 is on high speed). Jets 1 will automatically shut off after 15 minutes of operation on low/or high speed. Note: On 110 Volt systems there is only one speed on the jet pumps. JETS 2 BUTTON This button will activate the secondary hydro jet pump for additional hydrotherapy jet action. Press Jets 2 button once for low speed (Jets 2 triangle icon will flash). Press Jets 2 button again for high speed and again to turn off (Jets 2 triangle icon will stay solid when Jets 2 is on high speed). Pump will automatically turn off after 15 minutes of operation on high or low speed. JETS 3 BUTTON (VICTORIA AND PAVILION MODELS) This button will activate the 3rd hydro jet pump. Press Jets 3 button once for high speed and again for off position (Jets 3 triangle icon will stay solid when pump is on). Pump will automatically turn off after 15 minutes of operation. OPTION BUTTON Activates the 3 stage Blower. Press the Blower button once for high, again for medium again for low and then off. When operating, bubbles of air will come from air jets or Versa-Flo jets in the spa. Blower triangle icon will stay solid on high speed. Blower triangle icon will flash on medium or low speeds. The blower will turn off after 15 minutes of operation. Note: The spa light will begin flashing 15 seconds before the pumps shut off as a reminder, that the pump(s) cycle is about to end. Note: Saratoga spas are designed for maximum heat retention. The unit is not designed to cool water. If the set or desired temperature is below that of the ambient temperature, the unit will not be able to achieve this demand. Depending on the desired temperature, it may be necessary to add cool water to the unit to lower your spas water temperature. 45