In addition to this SOP, the policies and procedures of each operating company will be strictly observed by Rockwater personnel.
|
|
- James Bridges
- 5 years ago
- Views:
Transcription
1 SOP FB-009 (Revised MAR 2014) STANDARD OPERATING PROCEDURES-FLOWBACK Control of Trapped Pressure Section 1.0 Introduction and Background Rockwater Energy Solutions, Inc. (and all its affiliated and subsidiary companies, hereinafter collectively referred to as Rockwater ) is committed to providing its employees a safe working environment and avoiding injury to our contractors, customers, and neighbors. As part of our overall commitment to safety, Rockwater seeks to prevent acts or conditions that could result in injury and/or illness to any employee, customer, contractor, neighbor, and/or the environment. In an effort to prevent potentially harmful acts or conditions, Rockwater has developed this Standard Operating Procedure (SOP). This SOP will discuss steps to be taken to promote a safe process, as well as a list of potential hazards that should be identified and remediated prior to commencing these activities. This SOP will be reviewed and revised on an ongoing basis to keep pace with best oilfield practices. This SOP will be a part of the training provided to all affected employees when they begin their employment with Rockwater and any time the plan is changed. This SOP will also be reviewed with an employee if his/her responsibilities change under the plan. A written copy of this plan will remain in the regional Safety Office, and will be available for employee review. The Vice-President of Health Safety and Environment, or his agents, may be contacted by any employee if he/she needs additional information about this SOP. This SOP has been developed to assist affected employees with the operational steps that may be used to complete the task safely. It must be noted, however, that the experience and background of a trained flowback operator is essential to the success of any project or task. Nothing contained in this SOP is a substitute for each employee s individual judgment in any given situation. In the event that any employee believes that any task outlined in any SOP cannot be completed safely, then that employee should immediately halt the performance of such task and notify their direct supervisor. In addition to this SOP, the policies and procedures of each operating company will be strictly observed by Rockwater personnel. Section 2.0 Background and Process Steps, Control of Trapped Pressure Due to the inherent nature of flowback operations, pressurized piping and equipment is a daily hazard that must be mitigated. The purpose of this SOP is to outline the steps needed to identify potential sources of trapped pressure and then to mitigate those hazards. NEVER hammer on, apply force to, or manipulate any threaded connection (hammer union or National Pipe Thread [NPT]) while it is under pressure. o Isolate the equipment that will be worked on and bleed off pressure. Ensure that pressure is bled off entirely before work with the connection begins. Open the valve slowly and carefully to commence bleeding off the pressure. Pressure should be vented in a safe manner and directed toward a tank or to atmosphere.
2 o Make sure that no one is in the line of fire as pressure is bled off. Be wary of obstruction at point of bleed-off. Do not walk on or apply unnecessary force to pressurized iron. Hammer unions o Make sure that the unions are properly assembled, as per manufacturer specifications. Note that some mis-matched unions may nest or thread together, but they will have an extremely high probability of failure. o Hammer unions should be properly spaced and aligned. Do not connect hammer unions that are out of alignment (in a bind). Iron should be rigged up in a straight line, and all unions should match up neatly. o Use wood blocks as cribbing when making up hammer union connections. Wood blocks allow necessary clearance for hammer union wing, avoiding damage to containment. This will allow for a solid surface to support iron so that union can be properly tightened. o Prior to use, inspect hammer unions to ensure that they are in good condition. Inspect threads for dings and burrs. Clean and lubricate threads prior to every connection. Clean threads with a wire brush prior to applying lubricant. Inspect and clean wing threads. Inspect wing ears for damage. Damaged wing ears may shed metal shards while hammering, creating a potential hazard. o Wing ears should be ground down to a solid, undamaged surface. Visually inspect wing half segments (dogs) and the retention rings in each wing section. Inspect hammer union seal ring for any sign of wear. Replace if there is any sign of damage or wear The raised lip around the outside of the seal ring should be inserted first into the thread half connection, such that it fits into the groove in the union. o Do not cross-thread hammer unions when making up connections. o Hammer unions should be properly secured. Block up with wood blocks so that lines are resting on a solid surface. Use one of the following types of securement (as required for the operation): Cement blocks
3 o Chains and binders may be used Whip checks Nylon/Kevlar restraints Cable and clamp systems Secure iron such that operational flow will not cause iron to move. For NPT threaded connections, always review the following: o Always make sure that threaded connections are a matched pair, per manufacturer specifications. o Prior to use, inspect threads for signs of visible damage. o Always comply with manufacturers specifications for pressure rating and usage. o Use Teflon thread tape 2-3 wraps around threads Wrapped clockwise if looking at end of threaded piece o Do not cross-thread. o Tighten threaded connection completely. These connections should be tightened with a sledge hammer until they are fully secure. Do not over-tighten Boeing connections and other connections o Always comply with manufacturer specifications. o Properly maintain and lubricate unions. Contributing factors for the failure of pressurized iron include the following: o Vibration and movement. o Connections improperly made Force applied to connection o Damaged iron Washed out or excessively worn Damaged threads o Improper use Any usage outside of manufacturer specifications Pressure up iron gradually. o See SOP regarding pressuring up to manifold Utilize all pertinent safety practices. o Proper energy isolation, per requirements of operation. o Lock out/tag out as needed o Maintain good communication with everyone involved in operation Section 3.0 Potential Hazards Any time that flowback operations are in progress, the following potential hazards must be considered and mitigated: Latent natural gas Wind direction
4 Ignition sources within 100 feet of the wellhead and/or frac tanks Pressure Line of fire/body placement/grease valve placement Hydrogen Sulfide (H 2 S) Stored energy Overhead work or suspended loads Section 4.0 Other Safety Items In addition to the above potential hazards, the following items should be discussed and implemented during the pre-project tailgate safety meeting and JSA process, prior to commencement of onsite activities: All possible flammable gas or liquid sources are to be identified and controlled or remediated. All possible ignition sources are to be identified and controlled or remediated. Environmental controls; o Erosion and Sedimentation (E&S) controls in place? o E&S controls appropriately located? o E&S controls adequate for situation? Ensure that safety equipment and personal protective equipment (PPE) is onsite and available and properly utilized when necessary or otherwise required pursuant to this SOP or the operating company s policies and procedures. Access signs or tape (as required) are available. Non-sparking tools for potential leaks are available. Potential communication issues should be identified and resolved; o Among Rockwater employees. o Between Rockwater and other contractors onsite. Strategies for limiting site access should be discusses and implemented, if possible. Rally points for and routes for emergency evacuations should be identified. o Identify a secondary rally point, along with a secondary evacuation route. Grounding and bonding of tanks and equipment must be completed. Appropriate actions on/around tanks must be discussed. Spill/leak cleanup procedures must be reviewed. Containment requirements must be reviewed. Reporting requirements and procedures must be reviewed. Discuss that the integrity of lines is not guaranteed, and can be negatively impacted by o Pressure; o Vibration; o Torque; or o Binds. Record-keeping and project log requirements should be reviewed. Water for pressure testing, purging requirements and processes must be identified. A minimum of two workers must be present onsite at all times.
5 SOP In-Field Checklist, Control of Trapped Pressure NEVER hammer/apply force/manipulate any threaded connection while under pressure Always isolate equipment off all pressure, open valve slowly Do not walk on or apply unnecessary force to pressurized iron Make sure hammer unions are properly assembled, as per specs Ensure hammer unions are properly spaced/aligned, don t connect hammer unions that are out of alignment Use wood blocks as cribbing when making up hammer union connections Prior to use, inspect hammer unions to ensure that they are in good condition Clean and lubricate threads prior to every connection Inspect and clean wing threads Inspect wing ears for damage Visually inspect wing half segments and retention rings in each wing section Inspect hammer union seal ring for any sign of wear, replace as needed Do not cross-thread hammer unions when making up connections Hammer unions should be properly secured For NPT threaded connections, always review the following: Confirm threaded connections are a matched pair, as per specs Prior to use, inspect threads for signs of visible damage Always comply with manufacturers specs for pressure rating and usage Use Teflon thread tape Do not cross-thread. Tighten threaded connection completely; use sledge hammer until fully secure For Boeing connections (and other connections), always review the following: Always comply with manufacturer specs Properly maintain and lubricate unions Pressure up iron gradually Utilize all pertinent safety practices Proper energy isolation, per requirements of operation. Lock out/tag out as needed Maintain good communication with everyone involved in operation
In addition to this SOP, the policies and procedures of each operating company will be strictly observed by Rockwater personnel.
SOP FB-08 (Revised MAR 2014) STANDARD OPERATING PROCEDURES-FLOWBACK Hydrogen Sulfide Operations Section 1.0 Introduction and Background Rockwater Energy Solutions, Inc. (and all its affiliated and subsidiary
More informationIn addition to this SOP, the policies and procedures of each operating company will be strictly observed by Rockwater personnel.
SOP FB-10 (Revised MAR 2014) STANDARD OPERATING PROCEDURES-FLOWBACK Test Separator Operations Section 1.0 Introduction and Background Rockwater Energy Solutions, Inc. (and all its affiliated and subsidiary
More informationHOT OILING OPERATIONS ALL HSE PRC 172. Approved By: Manager, HSE Performance Assurance. Table of Contents
Owner: HSE Performance Assurance ALL HSE PRC 172 Approved By: Manager, HSE Performance Assurance Retention Code: CG01 CA Revised: March 2015 Review Frequency: Five years or less Table of Contents 1.0 Purpose...
More informationCOSASCO 3600 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE
COSASCO 3600 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE Rohrback Cosasco Systems, Inc. 11841 E. Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com
More informationINSTALLATION & MAINTENANCE INSTRUCTION
ARCHON Industries, Inc Liquid Level Gauges Models: BT-LLG ND-LLG INSTALLATION & MAINTENANCE INSTRUCTION Instruction No.: 1014.2 Revision Issued: 3/01/03 Approved: Engineering Manager Warning ONLY QUALIFIED
More informationCOSASCO 3600 PSI SINGLE SERVICE VALVE MAINTENANCE
COSASCO 3600 PSI SINGLE SERVICE VALVE MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 Revision History Record www.cosasco.com Page: 2 of
More informationCOSASCO 6000 PSI DOUBLE ISOLATION SERVICE VALVE MAINTENANCE
COSASCO 6000 PSI DOUBLE ISOLATION SERVICE VALVE MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com Page: 2 of 28 Revision History
More informationCOSASCO 6000 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE
COSASCO 6000 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com Page: 2 of 26 Revision
More informationHealth and Safety Program Inspections
POLICY: It is CPP s policy to maintain a program of safety inspections. The objective of this program is to control and mitigate hazards in the workplace and worksite. All CPP s facilities and worksites
More informationTriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7
TriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7 March 2014 Form FVC097 - Rev03 IMPORTANT: KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER.
More informationTHE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301
THE HF-300 SERIES Operating and Service Manual Series includes all variants of HF-300/301 Issue A July 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 3.1. Spring Loaded...
More informationAmmonia Purge Near Miss. Jason Clarke, Gulf Power Co.
Ammonia Purge Near Miss Jason Clarke, Gulf Power Co. Four generating units 2-82 MW 1-320 MW 1-500 MW Plant Crist Overview All four units run through a common scrubber The two large units utilize SCR technology
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationCOSASCO MODEL 60 RETRACTABLE 1500 PSI SYSTEM RETRACTOR KIT Work Instruction
COSASCO MODEL 60 RETRACTABLE 1500 PSI SYSTEM RETRACTOR KIT Work Rohrback Cosasco Systems, Inc. 11841 E. Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com
More informationASPEC Engineering HSE Management System. Work Instruction. 1 Objective. 2 Working in confined spaces. 2.1 What is a confined space?
1 Objective This work instruction has been developed to abide by the WHS Regulations (2011) and AS/NZ 2865 Safe working in a confined space. It has been developed around Hadden s typology for risk management,
More informationWHEATLEY Series 822/820 Swing Check Valve
Document Number: TC003001-12 Revision: 02 WHEATLEY Series 822/820 Swing Check Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS...3 SCOPE...4 INSTALLATION AND OPERATION
More informationTheory Assessment CS Confined Space Entry
Theory Assessment CS 100 - Confined Space Entry Version 8.02 Confined Space Entry Theory Assessment This Theory Assessment will form part of the formal assessment for the following unit/s of competency:
More informationIsolation Lockout and Tagging
PURPOSE To define the minimum system requirements for isolation of plant and equipment from hazardous substances, mechanical, electrical or other energy sources to protect all workers from personal injury
More informationIsolation and Lockout
Work Procedure Facilities Management UBCO-RMS-OHS-WP 16-001 Date Created: July 13, 1999 Date Updated: April 4, 2016 Supersedes: September 18, 2003 1. SCOPE Isolation and Lockout This procedure establishes
More informationREL-46 WARNING NOTICE 15 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD. Compatible with RELIABLE R15 and P Style dies. REL-46 Manual
OPERATORS ORS GUIDE REL-46 15 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD Compatible with RELIABLE R15 and P Style dies. RELIABLE EQUIPMENT & SERVICE CO., INC. 301 Ivyland Road Warminster, PA 18974
More informationSAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE CAT A-2 SOP #33
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE SAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE Date Issued:
More informationREL-510H WARNING NOTICE 12 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD
OPERATORS ORS GUIDE REL-510H 12 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD Compatible with U style and RELIABLE R12 shell type 12 ton compression dies. RELIABLE EQUIPMENT & SERVICE CO., INC. 92 Steamwhistle
More informationPoppetted Coaxial Drop Tube Assembly for use with Auto Limiter II. Installation Instructions
Poppetted Coaxial Drop Tube Assembly for use with Auto Limiter II Installation Instructions Franklin Fueling Systems 3760 Marsh Rd. Madison, WI 53718 USA Tel: +1 608 838 8786 800 225 9787 Fax: +1 608 838
More informationHydrostatic Pressure Testing
General An experienced or qualified person will be put in charge of hydro and should meet with the supervisor in charge of the job prior to test. Customer expectations should be clarified prior to beginning
More informationEntry to these spaces must be rigorously controlled to prevent serious injury or death.
Chapter 6 - Confined Spaces Chapter 6 Confined Spaces Definitions A confined space is defined as any structure that must be entered and that has or may contain dangerous concentrations of hazardous gases
More informationCB7 Bayonets Male & Female 1/4", 3/8, & 1/2 Size
12501 Telecom Drive, Tampa, FL 33637 Ph: (813) 978-1000 Fax: (813) 977-3329 www.cpc-cryolab.com INSTALLATION, OPERATING, AND MAINTENANCE INSTRUCTIONS 17/3.5.6 Rev. 0 CB7 Bayonets Male & Female 1/4", 3/8,
More informationKENNEDY VALVE OPERATION & MAINTENANCE MANUAL
2 54 ROTATING DISC GATE VALVE OPERATION & MAINTENANCE MANUAL Rel. 5/27/16 1 TABLE OF CONTENTS 3 General 3 Receipt & Inspection 4 Gate Valve Storage & Handling 5 6 Installation 7 Operation 8 Field Testing
More informationDate Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision #
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE MAINTENANCE TASKS Date Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision
More informationPDY TON HYDRAULIC CRIMPING TOOL WARNING
OPERATORS ORS GUIDE PDY-1220 12 TON HYDRAULIC CRIMPING TOOL All information found in this guide must be read and understood before use or testing of this tool. Failure to read and understand these warnings
More information6. Each mitigation was verified and individually documented
CHESM/MSW Field Verification Instructions: All information in sections A, B and C must be completed. Information in section B related to subcontractors should be obtained from the work crew if possible.
More informationTEM# Air Hammer Combo USER'S MANUAL
Air Tools TEM# 40 Air Hammer Combo USER'S MANUAL Read carefully and understand RULES FOR SAFE OPERATION and instructions before operating. Failure to follow the safety rules and other basic safety precautions
More informationPressure Regulators. Operating Instructions. Instrumentation
Pressure Regulators Operating Instructions FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THIS PRODUCT CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from the
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationOperation Manual. Carbon Filtration Industrial Drive, Orlinda, TN fax
Operation Manual Carbon Filtration 615-654-4441 sales@specialtyh2o.com 615-654-4449 fax TABLE OF CONTENTS Section 1 GENERAL 1.1 Warnings and Cautions... 1 1.2 Theory of Operation... 2 1.3 System Illustration...
More informationBUTTERFLY VALVES Series 800
BUTTERFLY VALVES Series 800 WARNING Before proceeding read ALL instructions and become familiar with the equipment and associated drawings. Follow ALL applicable safety regulations and codes for pressurized
More informationLockout Tagout Program
Lockout Tagout Program 1.0 INTRODUCTION Public Safety Department Environmental, Health and Safety (EHS) Division Standard Operating Procedure (SOP) #18 Purpose To ensure that machinery or equipment is
More information1 Purpose. 2 Responsibilities. 3 Policy Content ENVIRONMENTAL, HEALTH AND SAFETY STANDARDS. TITLE: CONFINED SPACE ENTRY Document Number: *
(Insert Company Logo) CORPORATE SAFETY MANUAL ENVIRONMENTAL, HEALTH AND SAFETY STANDARDS TITLE: CONFINED SPACE ENTRY Document Number: * Issue Date: Revision Date: * 1 Purpose The purpose of this policy
More informationInstallation, Operation & Maintenance Manual for Flo-Max Coupler Bracket Model FM150
Installation, Operation & Maintenance Manual for Flo-Max Coupler Bracket Model FM150 January 2013 Form FVC 084 - Rev 02 IMPORTANT: KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. 1.
More informationTHE BP-690 SERIES. Operating and Service Manual. Series includes all variants of BP-LF/MF-690/691
THE BP-690 SERIES Operating and Service Manual Series includes all variants of BP-LF/MF-690/691 Issue B April 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationSafety Manual Section 6 Confined Space
6. CONFINED SPACE ENTRY Introduction The following sections provide general guidelines and procedures for confined space entry. This section covers the following topics: Topic Page 6.1 Types of s... 6-2
More informationPlant Isolation Lock out/tag out Procedure
Plant Isolation Lock out/tag out Procedure Related Policy Responsible Officer Approved by Work Health and Safety Policy Approved and commenced November, 2014 Review by November, 2017 Responsible Organisational
More informationConfined Space Entry Program 8 CCR 5157
TABLE OF CONTENTS 1. POLICY... 2 2. PURPOSE... 2 3. SCOPE... 2 4. DEFINITIONS... 2 5. CONFINED SPACES IN THE SACRAMENTO STATE... 4 6. PERMIT SPACE ENTRY - PERSONNEL RESPONSIBILITIES... 4 6.1. CONFINED
More informationAE14 Automatic Air Vents for Liquid Systems Installation and Maintenance Instructions
1490050/7 IM-P149-06 CMGT Issue 7 AE14 Automatic Air Vents for Liquid Systems Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation 4. Commissioning
More information453 Series Steam Heated Vaporizing Regulator
ADI 0453A Certified ISO 9001:2000 453 Series Steam Heated Vaporizing Regulator INSTALLATION AND OPERATION INSTRUCTIONS Before Installing or Operating, Read and Comply with These Instructions Controls Corporation
More information97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO
97C COMPRESSOR KIT 12V PART NO. 00097 97C COMPRESSOR KIT 24V PART NO. 02497 98C COMPRESSOR KIT PART NO. 00098 97C 98C IMPORTANT: It is essential that you and any other operator of this product read and
More informationConfined Space Program
Type: POLICY Revision: 01 Owner: BRL Document Name: HSPOL 011 Status: Current Nov 2014 Review Date: September 2017 Effective Date: 01 January 2015 Total Pages: 6 Definitions: New Old Confined space means
More informationJacuzzi. J-CQ420 Cartridge Filter Installation and Operating Instructions
Jacuzzi J-CQ420 Cartridge Filter Installation and Operating Instructions IMPORTANT SAFETY PRECAUTIONS ATTENTION INSTALLER: This guide contains important information about the installation, operation and
More information35 TON HYDRAULIC PUNCH WARNING
OPERATORS GUIDE REL-35T-PNC 35 TON HYDRAULIC PUNCH NOTICE Sizes, weights and tool specifications listed in this manual are subject to change without notice. Please consult factory for information and updates.
More informationTHE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401
THE MF-400 SERIES Operating and Service Manual Series includes all variants of MF-400/401 Issue A October 2013 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationInstallation Operation Maintenance. Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow IOM.
Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow Model: FP 450-80 Installation Operation Maintenance PAGE 1 OF 5 1. Safety First BERMAD believes that the safety of personnel
More informationMethod statement for. The installation of. Precast Concrete Piles. (Site Name).
Method statement for The installation of Precast Concrete Piles At (Site Name). 1 of 5 Standard Operating Procedures for Pile Driving. This method statement will outline how the authorised/ competent operatives
More informationLockout Tagout Policy
Office of Environmental Health & Safety www.moreheadstate.edu/ehs 606-783-2584 Lockout Tagout Policy PURPOSE To establish procedures for the de-energization and isolation of energy sources or the lockout
More informationCA16 and CA16S-14 Air and Gas trap Installation and Maintenance Instructions
1483250/3 IM-P148-10 ST Issue 3 CA16 and CA16S-14 Air and Gas trap Installation and Maintenance Instructions 1 General safety information CA16 and CA16S-14 ½" and ¾" 2 General product information 3 Installation
More informationSafety Manual: Hazardous Energy. January, 2017
Safety Manual: Hazardous Energy January, 2017 9.0 Hazardous Energy Introduction Energized equipment in the workplace pose a significant risk of injury and death. If the unexpected energization or start-up
More informationTool Box Talk. Confined Space Entry New Construction Standard (2015)
Confined Space Entry New Construction Standard (2015) What s all this about Confined Space Entry and how does it affect the construction industry? On May 4, 2015 the Occupation Safety and Health Administration
More informationBSA6T and BSA64T Stainless Steel Bellows Sealed Stop Valves Installation and Maintenance Instructions
1843950/3 IM-P184-03 ST Issue 3 BSA6T and BSA64T Stainless Steel Bellows Sealed Stop Valves Installation and Maintenance Instructions 1. General safety information 2. General product information 3. Installation
More informationInstallation Instructions WARNING: WARNING: WARNING: LP AND HIGH ALTITUDE LP GAS CONVERSION KIT FOR UNITED STATES INSTALLATIONS
LP AND HIGH ALTITUDE LP GAS CONVERSION KIT FOR UNITED STATES INSTALLATIONS Installation Instructions For Model Series *G7/*GC2 Furnaces and Appliances Using Honeywell Gas Valves. BEFORE THE CONVERSION
More informationTHE OSHA LOCK-OUT/TAG-OUT STANDARD
PRESENTER'S GUIDE "LOCK-OUT/TAG-OUT" Training for THE OSHA LOCK-OUT/TAG-OUT STANDARD Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE OF MAJOR PROGRAM
More informationSAFETY MANUAL FOR FLAMMABLE PRODUCT TRANSFER
SAFETY MANUAL FOR FLAMMABLE PRODUCT TRANSFER SUPPLIMENT TO eom IMPORTANT READ THIS MANUAL BEFORE PRODUCT INSTALLATION, OPERATION, INSPECTION & MAINTENANCE Tougher and more rigid guidelines are being established
More informationThis written Compressed Gas Plan is kept at the corporate office and in the written Safety & Health Program.
Safety & Health Program 10627 Midwest Industrial Boulevard, St. Louis, MO Phone: 314-785-6425 Fax: 314-785-6426 Compressed Gas Plan Purpose It is the policy of EMA to permit only trained and authorized
More informationMST21 Stainless Steel Balanced Pressure Thermostatic Steam Trap
1250650/6 IM-P125-07 ST Issue 6 MST21 Stainless Steel Balanced Pressure Thermostatic Steam Trap Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
More informationIFTGS14 Ball Float Steam Trap ½" and ¾" with Integral Spiratec Sensor
6150350/3 IM-P615-12 ST Issue 3 IFTGS14 Ball Float Steam Trap ½" and ¾" with Integral Spiratec Sensor Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation
More information1.1 OHS Policy and Responsibilities
1.1 OHS Policy and Responsibilities At Canadian Rope Access Specialists Inc. safety is our primary concern and the health and safety of our employees, clients and contractors is of paramount importance
More informationCompressed Gases and Cryogens
Compressed Gases and Cryogens University of Tennessee Safety Guide HM-011 Document Contact: EHS Date effective: January 1, 2009 Revision Date: October 1, 2015 Purpose This guideline adheres to the Occupational
More informationINSTALLATION, OPERATION AND MAINTENANCE GUIDE
INSTALLATION, OPERATION AND Placement in Pipeline System When installing Process Development & Control s ElastoTITE Elastomer-Hinged Check Valves in a pipeline, a minimum of five pipe diameters should
More informationOKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM. Environmental Health and Safety. Established:
OKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM Environmental Health and Safety Established: Developed in accordance with OSHA Standard 29 CFR 1910.147 1 1.0 SCOPE. Oklahoma City Community
More informationBuild Your Own Flamethrower Step-by-step Manual
Build Your Own Flamethrower Step-by-step Manual Table of Contents: Parts List.. page 1 Operation...page 6 Diagrams. pages 7-9 Parts list: Required: Air tank (large) Pressure washer gun with high-pressure
More informationRULES OF THE OIL AND GAS PROGRAM DIVISION OF WATER RESOURCES CHAPTER DRILLING WELLS TABLE OF CONTENTS
RULES OF THE OIL AND GAS PROGRAM DIVISION OF WATER RESOURCES CHAPTER 0400-52-06 DRILLING WELLS TABLE OF CONTENTS 0400-52-06-.01 Drilling Equipment 0400-52-06-.03 Casingheads 0400-52-06-.02 Blowout Prevention
More informationTABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
More informationHIGH RATE BASKET STRAINER
Installation and Operation Instruction Manual INSMAN-105 High Rate Basket Strainer Phone: 951.656.6716 Toll-Free: 800.854.4788 www.yardneyfilters.com Yardney Water Management Systems, Inc. 6666 Box Springs
More informationSpiratec ST14, ST16 and ST17 Sensor Chambers and sensors
0862050/1 IM-P086-18 MI Issue 1 Spiratec ST14, ST16 and ST17 Sensor Chambers and sensors Installation and Maintenance Instructions 1. Safety Information 2. General product information 3. Installation 4.
More informationMARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM
MARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM INTRODUCTION Mariposa County ( County ) facilities have equipment and systems that must be deenergized to allow for safe cleaning, repairing, servicing, setting-up,
More informationState University of New York College at Oneonta
State University of New York College at Oneonta CONFINED SPACE ENTRY POLICY - PROCEDURE REVIEWED 05/11/17 CONFINED SPACE ENTRY - WRITTEN PLAN POLICY The State University College at Oneonta is committed
More informationLRS(H)4 Pressure-Reducing Regulator User Manual
LRS(H)4 Pressure-Reducing Regulator User Manual Read the complete manual before installing and using the regulator. 2 Safe Product Selection When selecting a product, the total system design must be considered
More informationTHE BP-301 SERIES. Operating and Service Manual. Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv)
THE BP-301 SERIES Operating and Service Manual Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv) Issue B October 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation...
More informationSafety Risk Assessment Working at Height: Mobile Tower Scaffold
Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees Mark Bloxidge H&S Manager 0208 821 5197 Working at height from Mobile Tower B Contractors/Sub contractors
More informationInstallation Instructions and valve Maintenance Rev. 0 of 21/09/15
ASSEMBLING PROCEDURE AND VALVE MAINTENANCE 1.0.... Safety Information 2.0.. INTRODUCTION 3.0 VARIATIONS 4.0..ASSEMBLING PROCEDURE FOR THE STEM 5.0 ASSEMBLING PROCEDURE FOR OUTLET CONNECTIONS 6.0 PROCEDURE
More information200 PSI COMPRESSORS - MODEL NUMBERS
200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read
More informationLockout / Tag out Program
Lockout / Tag out Program Presented by DOSHTI www.doshti.com You will learn Purpose of Lockout- Tag out Requirements for LOTO Types of Hazardous Energy Procedures for LOTO The OSHA Standard for the Control
More informationHEALTH AND SAFETY PROGRAM 201 HOT TAP PERMIT/FILLET WELD REPAIRS
Page 1 of 15 1.0 PURPOSE 1.1. Axiall, Plaquemine Complex, has developed this Hot Tap Permit Program to eliminate potential accidents, injuries, and to enhance employee protection. 1.2. To provide for the
More informationWESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107
WESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107 Draft Issued 12/97 Revised 11/00 Please direct any questions or comments about the applicability of this document to Luigi Marcone, WCSU
More informationLockout/Tagout Safety Policy
University of North Carolina Wilmington Environmental Health & Safety Workplace Safety Lockout/Tagout Safety Policy GENERAL The UNCW Environmental Health & Safety Department (EH&S) is authorized by UNCW
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationUIB30 and UIB30H Sealed Inverted Bucket Steam Traps for use with Pipeline Connectors
1130050/4 IM-P113-02 ST Issue 4 UIB30 and UIB30H Sealed Inverted Bucket Steam Traps for use with Pipeline Connectors Installation and Maintenance Instructions 1. Safety information 2. General product information
More informationSAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED. This Administrative Directive shall apply to all Town of Marana departments and employees.
SAFETY DIRECTIVE Title: Control of Hazardous Energy Lock-out/Tag-out/Try-out Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type
More information1 DRIVE INDUSTRIAL IMPACT WRENCH
1 DRIVE INDUSTRIAL IMPACT WRENCH 92622 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight
More information100C Air Compressor Kit
10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is
More informationCONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM Last updated: November 2017 1.0 PURPOSE Entry into a confined space represents a significant risk of serious injury or death to individuals not prepared for the hazards they may
More informationAPI MPMS Chapter 17.6 Guidelines for Determining the Fullness of Pipelines between Vessels and Shore Tanks
API MPMS Chapter 17.6 Guidelines for Determining the Fullness of Pipelines between Vessels and Shore Tanks 1. Scope This document describes procedures for determining or confirming the fill condition of
More informationInstallation, Operation, Maintenance Manual For Quick-Jaw Models AL363, L364 & AL366
Installation, Operation, Maintenance Manual For Quick-Jaw Models AL363, L364 & AL366 February 2014 Form FVC076 - Rev 07 IMPORTANT: KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. 1.
More information420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO
420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this
More informationTITAN FLOW CONTROL, INC.
PREFACE: This manual contains information concerning the installation, operation, and maintenance of Titan Flow Control (Titan FCI) Simplex Basket Strainers. To ensure efficient and safe operation of Titan
More informationSITE SAFETY PLAN AND NEW EMPLOYEE SAFETY ORIENTATION
SITE SAFETY PLAN AND NEW EMPLOYEE SAFETY ORIENTATION LOCATION: TSMF REVISED: 09-11-09 The following summarizes the orientation requirements for new employees at the facility. This plan augments the company
More informationConfined Space Entry Procedure
Purpose The purpose of this chapter is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation, entry and rescue
More informationSITE INSPECTION PROCEDURE FORM
SITE INSPECTION PROCEDURE FORM The Oil and Gas Commission, as regulators of British Columbia s oil and gas industry focuses on effectively regulating and managing the Provinces oil and gas sector. The
More informationType BBS-03, BBS-05, BBS-06, BBS-25
Type BBS-03, BBS-05, BBS-06, BBS-25 Sterile connection elements Sterile Verbindungselemente Raccords union stériles Operating Instructions Bedienungsanleitung Manuel d utilisation 1. THE OPERATING INSTRUCTIONS
More informationINTENDED USE TECHNICAL SPECIFICATIONS
1/2IN. HEAVY-DUTY AIR IMPACT WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationLRS(H)4 USER MANUAL. Read the complete manual before installing and using the regulator.
LRS(H)4 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to the
More informationManual Actuated Boiler Blowdown Valves
Manual Actuated Boiler Blowdown Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Operation 5. Maintenance 6. Spare parts p.1 1. Safety
More informationLeader s Guide ERI Safety Videos
1609 WORKING SAFELY WITH COMPRESSED GASCYLINDERS Leader s Guide ERI Safety Videos WORKING SAFELY WITH COMPRESSED GAS CYLINDERS PROGRAM SYNOPSIS: Safety must be a worker s number one priority when handling,
More information