SCOPE OF WORK. The Repair of the Mobile Harbour Crane leaking Luffing Cylinder
|
|
- Jasmin Hoover
- 5 years ago
- Views:
Transcription
1 EAST LONDON MULTI-PURPOSE TERMINAL Document Title: SCOPE OF WORK Scope Of Work Title: The Repair of the Mobile Harbour Crane leaking Luffing Cylinder TPT MHC luffing cylinder repair 1
2 1. BACKGROUND East London Transnet Port Terminals (TPT) has the Liebherr-550 Mobile Harbour Crane (MHC) that is used in handling various. The MHC has a hydraulic oil leak on the Luffing cylinder. The lifting capacity of the machine will be affected should we not attend to this. Secondly this poses an environmental impact with oil dropping uncontrollable. 2. PURPOSE Repair MHC leaking luffing cylinder. 3. SCOPE OF WORK 3.1. The scope will be in two options: Option 1 repair of cylinder option 2 replace cylinder with new Removal and refitting of hydraulic cylinder The appointed contractor will be responsible for: Safely removing the cylinder from the machine. Contractor must take in to consideration OEM specifications of the machine so that the removal does not negatively affect the machine. All tools and lifting equipment for the job. Removal of cylinder valve block. Containing oils to prevent environmental contamination. Once all the repairs are concluded on the cylinder the contractor will refit the cylinder to OEM specifications. All pins, bearings for the works must be catered for Cylinder Repairs Contractor will be responsible for the following: The contractor will be responsible for transporting the cylinder from TPT to contractor s premises. Drain hydraulic fluid and completely inspect the rod for more scarring which are causing the seals failure. Remove all the nuts, snap-ring or other devices that holds the rod end in place. TPT MHC luffing cylinder repair 2
3 Pull the rod completely out of the cylinder barrel to expose the piston and any other attached components to remove all the seals and replacing them and any other components to be replaced. Repair the damages on the rod. Clean and inspect the inside of the cylinder barrel, re-inspect the rod, piston and any other attaching parts. Install new seals on every applicable part to OEM specifications. Tighten the piston nut to its specified torque with a calibrated torque wrench. Reinstall all the parts back to the cylinder barrel and the cylinder. Carry out the Pressure test to OEM Specifications to ensure the safety, reliability, and leak tightness of the cylinder. Provide test certificate. OPTION 2 REPLACEMENT Contractor will be responsible for removal and refitting cylinder as per item 3.2. Supply new hydraulic cylinder as per OEM requirements. Carry out the Pressure test to OEM Specifications to ensure the safety, reliability, and leak tightness of the cylinder. Provide test certificate NOTE: For purposes of engaging the OEM for machine specific details use the following: Name: LHM 550 SERIAL Number: SHE File Requirements Below are some of the documents that make up a SHE file: a) Risk Assessment and Control measures for the specific activities to be performed b) Fall Protection Plan c) Signed section 37(2) form (from TPT)-Contractor Appointment d) Letter of Good Standing with Compensation Commissioner e) List of PPE to be used f) Registers vehicles/machinery/tools/safety Talks g) Team members medical certificates for the current financial year. h) Copies of Contractor SOP s / Work Instructions i) If Hot work to be done: Competence certificates for persons performing Hot Work j) List of equipment / tools with valid log sheets. Before awarding a service provider is expected to submit a full SHE file to SHEQ department for approval. TPT MHC luffing cylinder repair 3
4 5. GENERAL Working hours will be allowed from 07h00 to 15h00 (Monday to Friday), the successful contractor based on the amount of work and resources must determine own working hours needed to ensure all work is completed. All sandblasting should be done by suitably qualified artisans. All Scaffolding shall be erected by qualified, certified erecters and inspection certificate to be provided. Contractor shall practice good housekeeping and leave the site clean and tidy. When vacating the area the contractor will remove equipment and debris from site. Anything damaged by the contractor will be the responsibility of the contractor to repair that area at their own cost. Electrical power point will be provided. Toilet facilities will be provided by East London MPT. All work to be carried out must adhere to OHS Act 6. SAFETY RELATED ITEMS Safety of all electrical tools shall be checked and certified as per statutory requirement and certificates must be presented to TPT. Tenderer to provide inspection certificates of all lifting gear, equipment, scaffolding and rigging equipment as per statutory requirement and certificates must be submitted with the Tender Document. Prior to start of work a comprehensive safety file needs to be submitted to the TPT Safety, Health, Environmental and Quality (SHEQ) Department for approval. As part of the safety file a comprehensive risk assessment and method statement must be included for approval. All workers must be qualified for their specific work- proof of qualification must be included in safety file The contractor must adhere to Transnet Lockout Procedure and other relevant safety rules. The contractor must ensure that all its personnel have all the necessary protective clothing whilst within and` working in TPT premises. All personnel working in the TPT premises must undergo a complete induction course with the SHEQ department before commencing with the project on site. The contractor must ensure that they apply for a permit to work from TPT prior to commencement of works and for a hot work permit from Transnet National Port Authority (TNPA) prior to commencing with any work that might institute a hazard or an explosion through SHEQ department. TPT MHC luffing cylinder repair 4
5 The contractor must ensure that all the necessary fire protection and a qualified fire fighter will be on site whilst carrying out such work. Only after receiving permission in writing from TNPA can work commence. 7. SCHEDULING OF THE WORKS: The Tenderer with his first-hand knowledge of contracts of this nature, his own capabilities and the current activity in the engineering environment is to give a schedule time for execution of the works; Tenderers must note that other parts of the terminal will be operational during the execution of the works; and The successful contractor would be required to schedule his site work such that it does not interfere with the terminal s operations or there is minimal disturbance to operation. Signed: Name: Linamandla Busakwe Title: Technical Manager ELMPT Date: Sign: TPT MHC luffing cylinder repair 5
WHEATLEY Series 500 Swing Check Valve
Document Number: TC003001-13 Revision: 02 WHEATLEY Series 500 Swing Check Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS...3 SCOPE...5 INSTALLATION AND OPERATION
More informationMODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL
MODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL Index 1. List of components / General arrangement 2. Description 3. Handling 4. Installation 5. Actuators / Operation 6. Maintenance a. Changing
More informationCOSASCO 6000 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE
COSASCO 6000 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com Page: 2 of 26 Revision
More informationContractor handbook. Purpose
Page no: 1 / 6 Contractor handbook Purpose Mitie aims to ensure that the highest levels of performance are achieved by all persons working for us or on our behalf. We require the same level of performance
More informationDate Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision #
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE MAINTENANCE TASKS Date Issued: November 2011 Revision Date: December 2012 Review Date: December 2015 Revision
More informationINSTALLATION COMMISSIONING, OPERATION & MAINTENANCE MANUAL
WedgeRock RW Series Worm Gear Actuators INSTALLATION COMMISSIONING, OPERATION & MAINTENANCE MANUAL Revision 01 Date 4/3/17 Page 1 Table of Contents 1.0 INTRODUCTION... 4 1.1 PURPOSE... 4 1.2 AUDIENCE...
More informationSEMPEO SQA Unit Code FP2M 04 Maintaining mechanical devices and equipment
Overview This standard covers a broad range of basic mechanical maintenance competences that will prepare you for entry into the engineering or manufacturing sectors, creating a progression between education
More informationCOSASCO 3600 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE
COSASCO 3600 PSI SINGLE ISOLATION SERVICE VALVE (FR) MAINTENANCE Rohrback Cosasco Systems, Inc. 11841 E. Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com
More informationTHE BP-301 SERIES. Operating and Service Manual. Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv)
THE BP-301 SERIES Operating and Service Manual Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv) Issue B October 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation...
More informationSAPAG. Safety valves, type 5700 Storage, Use, Operation and Maintenance Instructions. IMPORTANT NOTICE
SAPAG IMPORTANT NOTICE Contents Important notice 1 0 Valve identification 2 1 Storage 2 2 Installation 2 3 Operation 2 4 Maintenance 3 4.1 Dismantling 3 4.2 Inspection 3 4.3 Repair 3 4.4 Assembly 4 4.5
More informationSection J. How to develop safety elements for project safety management system. How to develop safety elements for project SMS
Section J How to develop safety elements for project safety management system 1. Once the project management has developed or adopted a safety policy, it needs to develop safety elements to meet the objectives
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationSEMPEO SQA Unit Code FP2P 04 Maintaining fluid power equipment
Overview This standard covers a broad range of basic fluid power maintenance competences which will prepare you for entry into the engineering or manufacturing sectors, creating a progression between education
More informationEASTERN ENERGY SERVICES PTE LTD. 60 Kaki Bukit Place #02-19 Eunos Tech Park Singapore, SG Singapore Telephone: Fax:
2 Table Of Contents 1. Introduction 3 2. About this Manual 3 3. Contacting YZ Systems 3 4. Vessel Components 4 5. Specifications 5 6. Application 6 7. Theory of Operation 7 8. DuraSite Installation & Use
More informationTHE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301
THE HF-300 SERIES Operating and Service Manual Series includes all variants of HF-300/301 Issue A July 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 3.1. Spring Loaded...
More informationSERVICE INSTRUCTIONS PVWJ A-FRAME PUMPS -011/-014/-022 FOR TYPE P-1NN AND P-LNN PRESSURE COMPENSATING CONTROLS
Bulletin 947633 SERVICE INSTRUCTIONS PVWJ A-FRAME PUMPS -011/-014/-022 FOR TYPE P-1NN AND P-LNN PRESSURE COMPENSATING CONTROLS OILG0250 PURPOSE OF INSTRUCTIONS Figure 1. Typical Oilgear Type P-1NN and
More informationRelated Products: Auto Drain Valve. Model/Specifications. Model
Related Products: Auto Drain Valve /600 Drainage is automatically discharged in a reliable manner, without requiring human operators. Highly resistant to dust and corrosion, operates reliably, and a bowl
More informationSALCO PRODUCTS, INC. PRESSURE RELIEF VALVE STORAGE, INSTALLATION, OPERATING, MAINTENANCE/TESTING, AND INSPECTION INSTRUCTIONS
STORAGE INSTRUCTIONS Until it is time to install a new or reconditioned valve on the car, the valve must be kept in its original packaging in order to protect it from dirt and damage. INSTALLATION INSTRUCTIONS
More informationCOSASCO 3600 PSI SINGLE SERVICE VALVE MAINTENANCE
COSASCO 3600 PSI SINGLE SERVICE VALVE MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 Revision History Record www.cosasco.com Page: 2 of
More informationSOP GEN-007X Crane and Winch Operations
Page 1 of 7 SOP GEN-007X 1.0 Introduction 2.0 Responsibility 3.0 References 4.0 Training and Qualifications 5.0 Operational Inspections 6.0 Maintenance and Load Tests 7.0 Cranes 8.0 Winches 9.0 Mobile
More informationMeuangvang Development Co.LTD Standard Working Procedure 058 Use of Hydraulic Torqueing Devices
1. Application To provide a standard work procedure for as required in accordance with Meuangvang Development Co Ltd Safety Management Program 2. Revision Schedule Rev # Old Section Ref New Section Ref
More informationLOCKOUT SYSTEM AND POLICIES
LOCKOUT SYSTEM AND POLICIES Lockout System Purpose Employees health and safety takes top priority. Isolating hazardous energy to prevent sudden and unexpected energisation of machines, equipment, and processes
More informationWKM Model 320F Floating Ball Valve
Date: 4 WKM Model 320F Floating Ball Valve Installation, Operation, and Maintenance Manual 1 Date: 4 All the information contained in this manual is the exclusive property of Cameron. Any reproduction
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk WIRE ROPE CUTTER WCS75HDZ PRODUCT CODE No. 980482 INSTRUCTIONS FOR
More informationWHEATLEY WHEATLEY SERIES 500 SWING CHECK VALVE. Installation, Operation and Maintenance Manual
WHEATLEY SERIES 500 SWING CHECK VALVE STANDARD INTEGRAL SEAT & OPTIONAL REMOVABLE SEAT 2" FP - 6" FP 150# - 1500# 8" FP - 12" FP 150# - 900# API 6D and B16.34 2" FP - 4" FP 5000# DRILLING PRODUCTION VALVE
More informationInstructions: Use this format to prepare the security plans for ACP contracts. EVERY point has to be covered; if they do not apply, write N/A.
APPENDIX F - RISK CONTROL PLAN FORMAT FOR CONTRACTORS OF THE PANAMA CANAL Instructions: Use this format to prepare the security plans for ACP contracts. EVERY point has to be covered; if they do not apply,
More informationStandard Operating Procedure Measuring & Testing Equipment
Standard Operating Procedure Measuring & Testing Equipment Purpose: 7.6 Responsibility: 7.6d Scope To have a procedure to ensure that all is controlled, maintained and calibrated to ensure that Product
More informationSERVICE INSTRUCTIONS PVWJ A-FRAME PUMPS -011/-014/-022 FOR TYPE P-C AND P-K SOFT START PRESSURE COMPENSATING CONTROLS
Bulletin 947639 SERVICE INSTRUCTIONS PVWJ A-FRAME PUMPS -011/-014/-022 FOR TYPE P-C AND P-K SOFT START PRESSURE COMPENSATING CONTROLS OILG0260 Figure 1. Typical Oilgear Type P-C and P-K Soft Start Controls
More informationSERVICE INSTRUCTIONS P-A OR P-B ELECTRONIC PRESSURE COMPENSATOR, SERIES F1U CONTROLS
Bulletin 947556 SERVICE INSTRUCTIONS P-A OR P-B ELECTRONIC PRESSURE COMPENSATOR, SERIES F1U CONTROLS OILG0390 Figure 1. Typical Oilgear Type P-A or P-B Electronic Pressure Compensator, Series F1U Controls
More informationi) Filtration machine, measuring equipment and other related machinery
5 MVA TRANSFORMER SERVICE AND MAINTENANCE FOR TATA CHEMICALS MAGADI. SAFETY MEASURES AND REQUIREMENTS i) A thorough site risk assessment to be done before commencement of work. ii) All personnel involved
More informationCOSASCO 6000 PSI DOUBLE ISOLATION SERVICE VALVE MAINTENANCE
COSASCO 6000 PSI DOUBLE ISOLATION SERVICE VALVE MAINTENANCE 11841 Smith Avenue Santa Fe Springs, CA 90670 Tel: (562) 949-0123 (800) 635-6898 Fax: (562) 949-3065 www.cosasco.com Page: 2 of 28 Revision History
More informationContractor/Visitor Safety Orientation UNBC
Contractor/Visitor Safety Orientation UNBC 3333 University Way, Prince George, BC V2N 4Z9 Revised: October 2015 For All Emergencies call Security 250-960-7058 ***DO NOT DIAL 911*** Important UNBC Telephone
More informationREV0709. Parts List. Hydraulic Cylinder Model MODEL C SINGLE-ACTING, SPRING RETURN HYDRAULIC CYLINDER. Max. Capacity: 55.2 Tons at 10,000 PSI
REV0709 Parts List Hydraulic Cylinder Model 10312 MODEL C SINGLE-ACTING, SPRING RETURN HYDRAULIC CYLINDER Max. Capacity: 55.2 Tons at 10,000 PSI REV0709 Item No. Part No. No. Req d Description 1 10606
More informationYoke Block Instruction Manual
Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These
More informationKirby Morgan Manifold Block Monthly Inspection and Maintenance Checklist A2.2 B WARNING
Kirby Morgan Manifold Block Monthly Inspection and Maintenance Checklist A2.2 This inspection is the minimum recommended maintenance and should be performed at least ONCE A MONTH with manifold blocks in
More informationBUTTERFLY VALVES Series 800
BUTTERFLY VALVES Series 800 WARNING Before proceeding read ALL instructions and become familiar with the equipment and associated drawings. Follow ALL applicable safety regulations and codes for pressurized
More informationSERVICE INSTRUCTIONS P-2 DUAL PRESSURE COMPENSATOR, SERIES F1U CONTROL
Bulletin 947555 SERVICE INSTRUCTIONS P-2 DUAL PRESSURE COMPENSATOR, SERIES F1U CONTROL OILG0389 Figure 1. Typical Oilgear Type P-2 Dual Pressure Compensator, Series F1U Control for PVG 100/130 (F1U Series)
More informationSERVICE INSTRUCTIONS P-C SINGLE PRESSURE - SOFT START, SERIES F1U CONTROL
Bulletin 947557 SERVICE INSTRUCTIONS P-C SINGLE PRESSURE - SOFT START, SERIES F1U CONTROL OILG0392 Figure 1. Typical Oilgear Type P-C Single Pressure - Soft Start, Series F1U Control for PVG 100/130 (F1U
More informationNeedle valve. Contents. User s Manual. (1) Be sure to read the following warranty clauses of our product 1. (2) General operating instructions 2
Serial No. H-V024-E-7 Needle valve User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for transportation,
More informationService Call: Procedure for Bleeding the Hydraulic Leveling System. Tools Required: S-Wrench 1/2, 9/16, 5/8, 11/16, & 3/4 Drain Pan
Service Call: Procedure for Bleeding the Hydraulic Leveling System Tools Required: S-Wrench 1/2, 9/16, 5/8, 11/16, & 3/4 Drain Pan Model(s): 5TC, 6TC, 5FC, HRM, HR-OM, HRX, TCX, RM, RMX, XM, & XML Tech-Tip
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk WIRE ROPE CUTTER RCO40LP PRODUCT CODE No. 980503 INSTRUCTIONS FOR
More informationSWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6
Samark North Qld Pty Ltd SWMS SWMS No 0 Samark North Qld Pty Ltd ABN : 99 08 98 87 Electrical Contractors License C37 Page of 6 Safe Work Method Statement Title: SWMS:0 INSTALLING LIGHT POLES Work Method
More informationSERVICE INSTRUCTIONS P-1NN/G HORSEPOWER LIMITER WITH LOAD SENSE, SERIES F1U CONTROL
Bulletin 947554 SERVICE INSTRUCTIONS P-1NN/G HORSEPOWER LIMITER WITH LOAD SENSE, SERIES F1U CONTROL OILG0388 Figure 1. Typical Oilgear Type P-1NN/G Horsepower Limiter w/load Sense, Series F1U Control for
More informationPotable Water Truck Safe Work Procedure PTES_HSE_SWP_041. Name Date Signature. Author Geoff Selfe 25/01/2016. Reviewed Solomon Site 25/01/
Potable Water Truck Safe Work Procedure PTES_HSE_SWP_041 Name Date Signature Author Geoff Selfe 25/01/2016 Reviewed Solomon Site 25/01/2016 ----- Approved Michael Garkaklis 25/01/2016 Key Safety Acts Complete
More informationMUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5
operating Instructions manual MUELLER Mega-Lite Drilling Machine table of contents PAGE Equipment 2 Operating Instructions 3-4 Parts Information 5 Travel Charts 6-11! WARNING: 1. Read and follow instructions
More information2.0 Management Systems and Documentation
SHE Rules BOW142.3 1.0 Introduction This document details the safety, health and environment rules that apply to anyone accessing Arqiva sites and describes the standards of performance expected. This
More informationOperation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039. Name Date Signature. Author Jarred Hearle 27/11/2015
Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039 Name Date Signature Author Jarred Hearle 27/11/2015 Reviewed FMG Site Team 27/11/2015 ---------- Approved Geoff Selfe 27/11/2015
More informationOperating instructions. Bolt-on Bar Joist Anchorage
Reliance Industries, LLC Operating instructions for the Bolt-on Bar Joist Anchorage Model # 3072 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650 Fax (303)
More informationIsolation and Lockout
Work Procedure Facilities Management UBCO-RMS-OHS-WP 16-001 Date Created: July 13, 1999 Date Updated: April 4, 2016 Supersedes: September 18, 2003 1. SCOPE Isolation and Lockout This procedure establishes
More informationNAVSEA STANDARD ITEM. 1.1 Title: Contractor Crane, Multi-Purpose Machine and Material Handling Equipment at a Naval Facility; provide
NAVSEA STANDARD ITEM ITEM NO: 009-40 DATE: 26 MARCH 2018 CATEGORY: I 1. SCOPE: 1.1 Title: Contractor Crane, Multi-Purpose Machine and Material Handling Equipment at a Naval Facility; provide 2. REFERENCES:
More informationTHE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401
THE MF-400 SERIES Operating and Service Manual Series includes all variants of MF-400/401 Issue A October 2013 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationWHEATLEY Series 822/820 Swing Check Valve
Document Number: TC003001-12 Revision: 02 WHEATLEY Series 822/820 Swing Check Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS...3 SCOPE...4 INSTALLATION AND OPERATION
More informationConstant Pressure Crude Oil Container Model CPCCP
Installation, Operations, and Maintenance Manual Constant Pressure Crude Oil Container Model CPCCP The information in this manual has been carefully checked for accuracy and is intended to be used as a
More informationInstruction sheet for Hydraulic Cylinder
Oper at or smanual 1088710891 Hydr aul i ccyl i nder s Instruction sheet for Hydraulic Cylinder NOTE PLEASE READ AND FOLLOW THIS INSTRUCTION BEFORE YOU USE Yellow Jackit CYLINDERS. Carefully inspect all
More informationSAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE CAT A-2 SOP #33
SUNCOR ENERGY PRODUCTS DISTRIBUTION TERMINAL OPERATING MANUAL STANDARD OPERATING PROCEDURE SAFEWORK PRACTICES EQUIVALENCY PROCEDURE FOR ACCESSING FLOATING ROOF TANKS ON STORAGE TANKS IN SERVICE Date Issued:
More informationSERVICE INSTRUCTIONS PVWJ B-FRAME PUMPS -025/-034/-046 FOR TYPE P-1NN/F/J/K AND P-LNN/F/J/K LOAD SENSING CONTROLS
Bulletin 947637 SERVICE INSTRUCTIONS PVWJ B-FRAME PUMPS -025/-034/-046 FOR TYPE P-1NN/F/J/K AND P-LNN/F/J/K LOAD SENSING CONTROLS OILG0258 Figure 1. Typical Oilgear Type P-1NN/F/J/K and P-LNN/F/J/K Load
More informationSERVICE INSTRUCTIONS P-2NN/H DUAL PRESSURE COMPENSATOR WITH HORSEPOWER LIMITER, SERIES F1U CONTROL
Bulletin 947559 SERVICE INSTRUCTIONS P-2NN/H DUAL PRESSURE COMPENSATOR WITH HORSEPOWER LIMITER, SERIES F1U CONTROL OILG0413 Figure 1. Typical Oilgear Type P-2NN/H Dual Pressure Compensator with Horsepower
More informationContractors' Code of Safe Practice
Contractors' Code of Safe Practice Introduction As the controller of premises, The University of Hong Kong has a duty to ensure, so far as is reasonably practicable, the health and safety of all its employees,
More informationCO2 Tank Conversion Kit P.N , P.N , and P.N
Foodservice Group Multiplex Beverage Equipment Installation Instructions for CO2 Tank Conversion Kit P.N. 002247, P.N. 0022505, and P.N. 0025099 Introduction The following instructions cover the installation
More informationSite Specific Rules at Plants. Individual Unit Function: Safety Procedure No.: SOP-0135 Page: 1 of 8
Procedure No.: SOP-0135 Page: 1 of 8 Preparer: Owner: Approver: Safety Safety Safety 1. PURPOSE To provide BASF site specific rules for the protection of all MIDGA and contract personnel. These rules will
More information1 2 CONTENTS INTRODUCTION Owner Information 4 Warranty Registration 5 Safety Instructions Safety 6 Safety Decals 7 Safety Identification Labels 8 Safety Notice 10 Safety Standards 11 Risk Assessment 13
More informationSWMS No 007 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6
Samark North Qld Pty Ltd SWMS Manual SWMS No 007 Samark North Qld Pty Ltd ABN : 99 082 958 487 Electrical Contractors License C37121 Page 2 of 6 Safe Work Method Statement Title: SWMS:007 WORKING ON ENERGISED
More informationTHE BP-690 SERIES. Operating and Service Manual. Series includes all variants of BP-LF/MF-690/691
THE BP-690 SERIES Operating and Service Manual Series includes all variants of BP-LF/MF-690/691 Issue B April 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM ITEM NO: 009-40 DATE: 18 JUL 2014 CATEGORY: I 1. SCOPE: 1.1 Title: Requirements for Contractor Cranes, Multi-Purpose Machines and Material Handling Equipment at Naval Facilities; accomplish
More informationGeneral maintenance engineering applications
Unit 868 General maintenance engineering applications UAN: J/600/6007 Level: Level 2 Credit value: 12 GLH: 55 Relationship to NOS: Endorsement by a sector or regulatory body: Aim: This unit has been derived
More informationINSTRUCTIONS AND MAINTENANCE MANUAL SERIES: RT
INSTRUCTIONS AND MAINTENANCE MANUAL 05/11/2015 SERIES: RT cmo @cmo.es http://www.cmo.es page 1 ASSEMBLY THE RT VALVE COMPLIES WITH THE FOLLOWING: Machinery Directive: DIR 2006/42/EC (MACHINERY) Pressure
More informationConfined Spaces. This procedure applies to all workers of the Diocese of Maitland Newcastle (DoMN).
Purpose To provide guidance in controlling the risks associated with confined spaces including identifying confined spaces, working in a confined space and issuing confined space entry permits. Scope This
More informationSAILTEC, INC CONGER COURT, OSHKOSH, WI USA
OK to make this valve hand tight. Pin Mount Style Integral lies 4-5 Degrees above Horizontal. If you store your Hunter "bow down" you will get air-lock in the Integral. Slot Mount Style Pump Body "Down"
More informationSWMS No 001 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 5
Samark North Qld Pty Ltd SWMS Manual SWMS No 00 Samark North Qld Pty Ltd ABN : 99 082 98 87 Electrical Contractors License C372 Page 2 of Safe Work Method Statement Title: SWMS:00 USING PORTABLE LADDERS
More informationHYDRAULIC CYLINDER TEST
In the event that a coach equipped with hydraulic slide-outs begins to experience room drift, whether the room drifts out after retract, or drifting in after extension, a test of the hydraulic cylinders
More informationP5513. Users Manual. Pneumatic Comparison Test Pump. Test Equipment Depot Washington Street Melrose, MA TestEquipmentDepot.
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com P5513 Pneumatic Comparison Test Pump Users Manual PN 3963372 November 2010 2010 Fluke Corporation. All
More informationFlexfence Swaging Unit. Product Manual. Release 02/16.
Product Manual www.ingalcivil.com.au 1.0 Safety Precautions 1.1 Personal Protection While operating this equipment it is recommended that the following personal protective equipment be worn; Long sleeve
More informationARGUS MODEL C PIG VALVE
ARGUS MODEL C Installation, Operation, and Maintenance Manual Dedicated to Improving Your Operations for Over 50 Years Argus Machine Co. Ltd. 5820-97 Street, Edmonton, Alberta, Canada T6E 3J1 Phone: (780)
More informationDuPage County Environmental, Safety, Health & Property Loss Control Program Hazardous Energy Control (Lockout/Tagout)
Purpose: To provide the minimum requirements for the lockout or tagout of energy isolating devices whenever work is performed or servicing is done on County of DuPage machinery, equipment, vehicles and
More informationPlant Risk Assessment Self Propelled Scissorlift type Elevating Work Platform Model: S2755RT
134 Ogilvie Avenue, Echuca 3564 Plant Risk Assessment Self Propelled Scissorlift type Elevating Work Platform This Hazard Identification & Risk Assessment has been prepared based on several key assumptions:
More informationRisk Assessment Form
Assessment Form GROUP #1 Bow Thruster Overhaul TABE #1 Additional Control 1 Preparation of tools truck by tools Proper tools 1 1 Oil pill lip and Fall Housekeeping 4 2 M 2 Isolate Hydraulic system and
More informationIndex Table. Model 794. Installation, Operating and Maintenance Instructions
CLOCKWISE MANUAL MAKING INTO CCW TABLE Index Table Model 794 Installation, Operating and Maintenance Instructions Black & Webster Products Division 545 Hupp Ave. P.O. Box 831, Jackson, Michigan 49204 2009
More informationGeneral maintenance engineering applications
Unit 068 General maintenance engineering applications Level: 2 Credit value: 12 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover
More informationTech Tips. Service Call: Adjustable Hydraulic Valves Flow controls Pressure controls Sequence valves Holding valves
Service Call: Adjustable Hydraulic Valves Flow controls Pressure controls Sequence valves Holding valves Tools Required: Flow Meter Pressure gauge Holding valve test block Wrenches for installation of
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk WIRE ROPE CUTTER RCO40 PRODUCT CODE No. 980502 INSTRUCTIONS FOR INSTALLATION,
More informationYoke Block Instruction Manual
Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These
More informationPressure Regulators. Operating Instructions. Instrumentation
Pressure Regulators Operating Instructions FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THIS PRODUCT CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from the
More informationKIRBY MORGAN DEEP SEA DIVING HELMETS ALL MODELS HELMET AND EMERGENCY GAS SYSTEM DAILY SET-UP AND FUNCTIONAL CHECKLIST APPENDIX A2.
KIRBY MORGAN DEEP SEA DIVING HELMETS ALL MODELS HELMET AND EMERGENCY GAS SYSTEM DAILY SET-UP AND FUNCTIONAL CHECKLIST APPENDIX A2.3 01-25-17 THIS DAILY SET-UP AND FUNCTIONAL CHECKLIST SHOULD BE COMPLETED
More informationAllspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk SOFT LINE CUTTER SL55 PRODUCT CODE No. 980504 INSTRUCTIONS FOR INSTALLATION,
More informationDBML-60/80 Squeeze Tool
DBML-60/80 Squeeze Tool OPERATORS MANUAL Description The Mustang Model DBML-60/80 Hydraulic squeeze tool has been manufactured since 1995. A Mustang 3 3/4 bore doubleacting cylinder producing 41,000 lbs
More informationModel 7989T Steel Pipe Squeezer Sch. 40 & Sch. 80. Operations Manual
10-12 Steel Pipe Squeezer Sch. 40 & Sch. 80 Operations Manual 1.0 Introduction This manual is issued as a basic operation manual covering the Regent Model 7989T, Pipe Squeezer and Pump as manufactured
More informationWHS CONTRACTOR INFORMATION PACKAGE
WHS CONTRACTOR INFORMATION PACKAGE Introduction This information package provides Informa exhibitors and contractors with important information that will be required to plan and manage work on all stages
More informationAir Tractor Preventative Maintenance Manual And Troubleshooting
1.0 Overview This maintenance schedule will assist in the maintenance and troubleshooting procedures for the Unified Industries Air Tractor. The first portion of this section details the general maintenance
More informationHot Tapping Machine. OPERATIONS MANUAL and OPERATING INSTRUCTIONS
262-2040 Hot Tapping Machine For performing 1/4 6 Hot taps 285 psi or less. Municipal Water, Sewage, & Building Services Use OPERATIONS MANUAL and OPERATING INSTRUCTIONS WARNING: These instructions are
More informationINSPECTORATE FOR DIVING EQUIPMENT SERVICING & TESTING CODE OF PRACTICE CP11:2011
D003 INSPECTORATE FOR DIVING EQUIPMENT SERVICING & TESTING CODE OF PRACTICE CP11:2011 For INSPECTING and TESTING Transportable Pressure Receptacles (Cylinders) for Breathing Gases manufactured from Steel
More informationPV4 and PV6 Piston Valves
1181250/1 IM-P118-05 ST Issue 1 PV4 and PV6 Piston Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Commissioning 5. Operation 6.
More informationHANDBOOK. Squeeze Off Unit SOU 400. Please refer any queries to:
HANDBOOK Squeeze Off Unit SOU 400 Please refer any queries to: Hy Ram Engineering Co Ltd Pelham Street Mansfield Nottinghamshire NG18 2EY Telephone No: (01623) 422982 Please note all queries should state
More information310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment
OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility
More informationKMB 18/28 (BANDMASK) OVERHAUL, MAINTENANCE, AND INSPECTION CHECKLIST APPENDIX A
KMB 18/28 (BANDMASK) OVERHAUL, MAINTENANCE, AND INSPECTION CHECKLIST APPENDIX A2.1 01-31-17 THIS INSPECTION AND MAINTENANCE SHOULD BE PERFORMED AT LEAST ANNUALLY AND AS DICTATED BY CONDITION REVEALED DURING
More informationProduct Bulletin No.: D99-RRV2015-PIB-001
Product Bulletin No.: D99-RRV2015-PIB-001 Titan BX Automatic Pressure Relief Valves Issue Date: April 22, 2016 Subject: Product: Affected Assemblies Objectives: Structural failure of a Titan Type BX pneumatically-operated
More informationRS(H)10,15 USER MANUAL. Read the complete manual before installing and using the regulator.
RS(H)10,15 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to
More informationIPSWICH. Port Safety Notice
IPSWICH Port Safety Notice 19th October 2018 1 Associated British Ports Ipswich Port Safety Notice to Masters Introduction: This Port Safety Notice has been developed and communicated to provide general
More informationLOCK-OUT / TAG-OUT SYSTEM & PROCEDURE
Date Adopted 8/04/2008 Due for Review 8/4/2009 Business Unit HR & Safety Current Policy Date 8/4/2008 LOCK-OUT / TAG-OUT SYSTEM & PROCEDURE 1.0 PURPOSE 2.0 SCOPE To prevent injuries to persons or damage
More informationTroubleshooting Lift Cylinder Drift and Tilt Cylinder Drift
Troubleshooting Lift Cylinder Drift and Tilt Cylinder Drift Compact Track Loader: All Multi Terrain Loader: All Skid Steer Loader: All ReferenceTesting and Adjusting, RENR4837, "216, 226, 232, and 242
More informationSERVICE MANUAL. Technical Bulletin No GEOPROBE GH40 HYDRAULIC HAMMER. PREPARED: February, REVISED: April, 2002 A DIVISION OF KEJR, INC.
This document describes charging the GH40 Hydraulic Hammer with nitrogen gas. Text and illustrations were taken directly from the service manual shown below. GEOPROBE GH40 HYDRAULIC HAMMER SERVICE MANUAL
More information