CC24-7 ELITE. Temperature Controller USER S MANUAL Legion Dr. Mason, MI USA April 2011 Ph. (517) Fax (517)

Transcription

1 Temperture Controller CC24-7 ELITE USER S MANUAL Ative Alrms Selet Progrm Room Set Point Min Vent Timer Vent Door / Stti Pressure Tunnel Curtin Messge Center USER DEFINED SHORT-CUT KEY Aeroteh, In. FORM: QM Legion Dr. Mson, MI USA April 2011 Ph. (517) Fx (517)

2 WARNINGS The wrrnty n e voi if this prout is use in mnner not speifie y the mnufturer. Every effort hs een me to ensure tht this mnul is omplete, urte n up-to-te. The informtion ontine in it is however sujet to hnge without notie ue to further evelopments.

3 TABLE OF CONTENTS 1. INTRODUCTION Preutions Symols of the Mnul Controller s Overview Desription of the Controller Wht s New Min Fetures MOUNTING INSTRUCTIONS Instlling the Controller on the Wll Connetions Min Wiring Alrm Connetion Proe Inputs V Output Connetion Instlling Stti Pressure Sensor Tuings USER INTERFACE Lotion of the Controls Prmeter Ajustment Sttus LEDs CONTROLLER SETUP Time & Dte Dy / Night Times Psswor Controller Progrms & Sesonl Settings Seleting Progrm Copying / Psting Progrm Configurtion Mesuring Units Instlltion Setup Proe Settings Proe Assignment Proe & Wter Meter Clirtion Rely Assignment Priniple of Opertion Heters Rely Assignment Fn Stge Rely Assignment Ventiltion Relys : Priniple of Opertion Fn Stge Rely Settings Vrile Outputs & Timer Settings Copying / Psting Fn Stge Relys Curtin, Vent Door & Atti Relys Clok Output Relys Clok Output Relys Seleting Common Relys Cooling Output Relys Bkup Box Rely Feeer Rely Test Moe Version TEMPERATURE SETTINGS Temperture Set Point Set Point Settings Set Point Curve VENTILATION & COOLING Minimum Ventiltion Minimum Ventiltion Cyles Priniple of Opertion Settings Minimum Ventiltion Curve Priniple of Opertion Min Vent. Curve Settings Min Vent. Rmp & Compenstion Stge 1 On Time Rmp On Time Compenstion Below the Set Point Fn Stges Priniple of Opertion On/Off Fn Stges Vrile Outputs V Ventiltion Output Settings Fn Stge Settings V Output Fn Settings Tunnel Curtin Stti Pressure Curtins Priniple of Opertion Settings Timer-Bse Curtin Priniple of Opertion Settings Inlets & Vent Doors Inlet on Externl SB Moules Settings Pressure-se Vent Doors Priniple of Opertion Settings Timer-Bse Vent Doors Priniple of Opertion Settings Atti Vent Pressure-se Atti Vent Timer-se Atti Vent Cooling Outputs Nturl Ventiltion Priniple of Opertion Trnsition Between Nturl & Tunnel Ventil Settings CC24-7 ELITE rev.23 3

4 7. HEATERS Heting Stges Heter Curve Priniple of Opertion Settings Copy/Pste Het Curves Het Mts (0-10V Heting Outputs) LIGHTS Priniple of Opertion Ativting Aitionl 0-10V Light Outputs Light Progrm Settings TECHNICAL SPECIFICATIONS TRANSFER MENU Sreen Contrst Communition Spee Upte/Bkup Proess INSTALLATION REPORT INDEX CLOCK OUTPUTS RELATIVE HUMIDITY (RH) CONTROL Priniple of Opertion RH Comp. on the Min. Ventiltion Intensity RH Comp. with Heting Outputs RH Comp. on the Mist Output Settings ALARMS Alrm Log Alrm Conitions & Settings Temperture Alrms Stti Pressure Alrms SP Alrm Settings: Low SP Alrm Rely Hi Stti Pressure Alrm Settings Wter Spill Alrms Feeer Alrms MONITORING FUNCTIONS Current Conitions History Monitoring the Animl Age & Numer Messge Center Messge Log Clering the Messge Log Serviing Sheule Rely Run Time CC24-7 ELITE rev.23

5 1. INTRODUCTION 1.1. Preutions WARNING: Re n sve these instrutions! Sfety my e jeoprize if the equipment is use in mnner not speifie y the mnufturer. Crefully re n keep the following instrutions for future referene. We strongly reommen instlling supplementry nturl ventiltion s well s kup thermostt on t lest one ooling stge. Although fuses t the input n outputs of the ontroller protet its iruits in se of n overlo or over-voltge, we reommen instlling n itionl protetion evie on the ontroller s supply iruit. The room temperture where the ontroller is lote must lwys remin etween 32 F n 104 F (0 C to 40 C). Inoor use only! To voi exposing the ontroller to hrmful gses or exessive humiity, it is preferle to instll it in orrior. If the equipment is use in mnner not speifie y the mnufturer, the protetion provie y the equipment my e impire. Do not spry wter on the ontroller! In orer to len the ontrol, wipe it with mp loth. Before serviing or lening unit, swith power off t servie pnel n lok the swith isonneting mens to prevent power from eing swithe ientlly. When the servie isonneting mens nnot e loke, seurely fsten prominent wrning evie, suh s tg, to the servie pnel Symols of the Mnul Wrning. Re the following text refully; it ontins importnt informtion whih, if ignore, my use the ontroller to operte improperly. High Voltge. Hzr of eletril shok. Re the messge n follow the instrutions refully. Py ttention. The following text ontins very useful informtion. Both iret n lternting urrent (AC/DC). Diret urrent (DC). Alternting urrent (AC). Erth Groun Terminl Primrily use for funtionl erth terminls whih re generlly ssoite with test n mesurement iruits. These terminls re not for sfety erthing purposes ut provie n erth referene point. For Customer Use: Enter elow the seril numer lote on the sie of the lrm system n keep this informtion for future referene. Moel: Seril numer: Dte instlle: CC24-7 ELITE 1.3. Controller s Overview Desription of the Controller The CC24-7 ELITE is n eletroni evie use for environmentl ontrol in livestok uilings. It llows to mintin speifie trget temperture y ontrolling the opertion of ventiltion n heting equipment. The ontroller n operte the following inputs & outputs: OUTPUTS: 100 On/Off relys lote in externl rely pnels. 8 heting stges (n the possiility to simulte up to 16 stges); 16 fn stges; 8 lok outputs; 1 tunnel urtin; 4 nturl ventiltion urtins; 1 stir fn output; 4 ooling outputs; 1 inlet output use to onnet up to 10 externl ir inlet moules (SB moules) or to onnet vent oor. 1 inlet output use to onnet n tti vent, supplementry siewll vent (vent oor) or supplementry tunnel urtin. 2 Vrile-spee outputs; V outputs use for: - het mts; - lights; - fns. INPUTS: 8 insie temperture proes; 1 outsie temperture proe; 1 stti pressure sensor; 1 humiity sensor; 10 wter meters; 2 ry ontt inputs to monitor: - 1 feeer; - 1 evie for the messge enter. Refer to the en of this mnul to onnet the sensors n los. CC24-7 ELITE rev.23 5

6 Wht s New The ontroller now uses new n improve ore pltform. Here s the list of improvements relte to this new pltform: Sreen ontrst The sreen ontrst n now e moifie iretly from the TRANS- FER menu. Stility of the sreen ontrst The ontroller now ensures stility in the sreen ontrst when the isply is sumitte to temperture hnges. A-BOX Rey The high spee ommunition protool require to onnet the ontroller to the A-BOX system n now e tivte from the TRANSFER menu. There is no nee to hnge mirohip insie the ontroller to hnge the ommunition spee. Esier firmwre uptes Pltform firmwre uptes n now e ownloe from USB r (see TRANSFER menu). There is no nee to hnge mirohip insie the ontroller to mke this upte. Simplifie firmwre The new ore pltform now uses one firmwre only. Memory r The lssi memory r (Config200 r) hs een reple y stnr USB rive (inlue with the ontroller). Improve nvigtion proess Sroll rs, pop-up menus n pge-up/ pge-own funtions were e to ese nvigtion insie the menus. Less ontroller reset Inste of resetting when there is instility in the power supply, the ontroller now isplys Zero Crossing lrm messge. Event uffer The ontroller s event log n e sve on the USB r (see TRANSFER menu) Min Fetures Very lrge LCD isply A lrge sreen provies n effiient interfe for isplying, monitoring n justing the prmeters. 4 Controller progrms The ontroller hs 4 progrms to ontrol the room temperture. You n thus hoose progrm tht suits the urrent ge of the nimls for instne. Sttus LEDs Pilot lights inite the sttus of the ontroller s outputs, llowing you to monitor the system s opertion without hving to enter the uiling. Removle onnetors You n remove the onnetors from the min or to mke the onnetions. Minimum ventiltion yle When ventiltion is not require to reue the room temperture, the fn outputs n run either ontinuously or intermittently to reue the humiity level n supply oxygen to the room. Proe reings reore for pst ys The ontroller keeps ily reor of the minimum n mximum reings of the stti pressure n humiity proes for the pst 75 ys. The minimum n mximum reings of eh iniviul temperture proe is lso reore ily for the pst 7 ys. Wter monitoring Ten pulse inputs re provie to monitor the wter onsumption. The ontroller keeps ily reor of the wter onsumption for the pst 60 ys. Alrm mngement Alrms re provie for high-low tempertures, efetive proes n other system filures. The ontroller keeps in memory the 25 previous lrm onitions. Eight inepenent temperture proe inputs Eight insie temperture proes n e onnete to the ontroller in orer to otin n urte reing of the verge house temperture n fster retion time. Humiity Control The ontrol offers mny wys to ompenste for high or low humiity levels. 0-10V outputs Four 0-10V outputs n e use to tivte itionl fns, het mts, or lights. Control of the ir inlet movement If the ontroller is use in omintion with one or more ir inlet moules, the movement of ir inlets n e oorinte with the opertion of the fns, using potentiometer lote on the pnel rive. This llows the ir inlets to e juste orretly, without the influene of unontrollle ftors suh s win or ir from joining rooms. Reupertion of the wrm ir in the tti In orer to mke energy svings, the ontroller n extrt the wrm ir from the tti n sen it k into the room. Nturl ventiltion The ontroller n ontrol up to 4 urtins lote in inepenent nturl zones. Tunnel urtin ontrol An enwll urtin n e ontrolle oring to the room temperture or oring to the stti pressure level in the house. Vent oors The ontroller n open n lose vent oors oring to timer t the strt-up of eh fn stge or it n oorinte the vent oor opertion with the stti pressure level of the room. Psswor protetion A psswor is use to restrit ess to some of the ontroller setup funtions. Bkup ttery A kup ttery llows the unit to keep time in se of power filure. Overlo n overvoltge protetion Resettle fuses re provie t low-voltge inputs n outputs of the ontroller to protet its iruitry in the se of n overlo or overvoltge. Computer ontrol The ontroller n e onnete to omputer, thus mking it possile to entrlize the mngement of informtion n iversify ontrol strtegies. Test moe The test moe llows the user to simulte temperture hnges n verify the performnes of the ontroller. 6 CC24-7 ELITE rev.23

7 2. MOUNTING INSTRUC- TIONS 2.1. Instlling the Controller on the Wll Fsten the two metl rkets on the mounting holes lote ehin the ontroller using six srews. Then, mount the enlosure on the wll using four other srews. Leve lerne of t lest 16 to the left of the enlosure to llow the over to e remove for mintenne Connetions Min Wiring Refer to the wiring igrm enlose with this user s mnul to onnet the ontroller. Drill holes t the ottom of the enlosure to pss the wires n instll wtertight onnetors to prevent wter from entering in the enlosure. Do not mke ny holes t the sie n top of the enlosure. All wiring must e one y n uthorize eletriin n must omply with pplile oes, lws n regultions. Mke sure power is off efore oing ny wiring to voi eletril shoks n equipment mge Alrm Connetion There re two types of lrms on the mrket. One type tivtes when urrent is ut off t its input; the other type of lrm tivtes when urrent is supplie t its input. For n lrm of the first type, use the NC terminl s shown on the wiring igrm. For n lrm of the seon type, use the NO terminl Proe Inputs Proes operte t low voltge n re isolte from the supply. Mke sure tht proe les remin isolte from ll high voltge soures. In prtiulr, o not route the proe les through the sme eletril knokout s other les. Do not onnet the shiel from the proe le to terminl or groun. Extening proe: Eh proe n e extene up to 500 feet (150 meters). To exten proe: Use shiele le of outsie imeter etween n in (6.22 n 6.60 mm) (the le imensions shoul not e uner 18 AWG) to ensure the le entry is liqui tight. Do not groun the shieling. It is preferle to soler the le joint to ensure proper ontt etween the two les. Do not run proe les next to other power les. When rossing over other les, ross t 90. Defetive proes: An lrm is generte when efetive proe is etete. Defetive proes re ientifie in the Alrm Log menu. Refer to hpter 11 for further informtion on the lrms V Output Connetion It is reommene to use 18 to 22 AWG wire to onnet the evies to the 0-10V outputs. This type of output n e use to onnet vrious evies suh s het mts or fns. CC24-7 ELITE rev.23 7

8 2.3. Instlling Stti Pressure Sensor Tuings The integrte stti pressure sensor is very roust n relile tool for ontrolling your vent oor openings. However, the instlltion requires some re in orer to ensure tht the ontroller funtions properly. 10 of ler tuing n inset filters re provie with the ontroller. Insert plsti inset filter t the en of eh tue s illustrte. Leve lerne etween the en of the tue n the plsti filter to voi ostruting the tue. Cler tue Inset filter Free spe ) Using the Atti s Referene The tti is usully onsiere goo referene s long s the following onitions re oserve: i) The tti must hve suffiient openings on ll sies of the uiling to llow outsie ir to permete it n ensure tht no permnent pressure ifferene uils up etween the tti n outsie ir (usully, n tti with openings overing 4% of its re is suffiient). To test the suitility of the tti s referene, ple the referene tue in the tti n the room tue outsie or in room with wie openings to the outsie (for exmple, the entrne of house with wie open oors so the pressure in the room is the outsie pressure). The pressure ifferene must e ner zero. You ll notie tht the win my inue pressure ifferene for short perios of time (euse of rething effet). This is the reson the pressure sensor hs time ely on ny tion. The tti is goo referene if you on t see ny permnent pressure ifferene. ii) The tti must e irtight with respet to the jent livestok floor. This wy, no pressure ifferene is inue etween the referene (tti) n outsie pressure ue to the tion of fn. To test the irtightness of the tti with respet to the ventilte room, ple the referene tue in the tti n the room tue outsie or in room with wie openings to the outsie. There shoul e no sensitive pressure rop when you tivte or etivte the fns in the spe next to the tti. No vuum shoul uil up in the tti. Choosing Goo Referene The purpose of the stti pressure sensor is to mintin slight vuum insie the uiling s ompre to the outsie tmospheri pressure. This pressure ifferene (usully in the orer of 0.03 to 0.09 inhes of wter) inues the esire ir spee t the vent oor for n optimum irflow istriution. It is importnt to unerstn tht the pressure ifferene to e ontrolle is the one tht exists etween either sie of the vent oor wll. We must therefore e sure tht the referene is representtive of the urrent outsie pressure. Testing the suitility of the tti Air outlet (room) Atti Plsti inset filters Air inlet (referene) 8 CC24-7 ELITE rev.23

9 Instlltion of n Extene Referene Tue into the Atti: It my hppen tht the supplie 10 of ler tuing isn t long enough to lose the irflow iruit etween the room n the tti (referene). In this se, we reommen instlling the ontroller within 10 of the room to e ontrolle. Use the ler tuing to reh the room n exten the referene tue with lrger pipe or tue (1 pipe is goo) to the lotion of the referene (see igrm). At the referene lotion, the opening of the pipe shoul e s lrge s its setion. It shoul point ownwrs, using n elow if neessry, n e protete from ny iret irflow from the outsie. The use of orse sreen is reommene to stop insets from plugging up the pipe. One the instlltion is omplete, perform the ove tests to vlite the referene. Testing the irtightness of the tti Air outlet (room) Air inlet (referene) Atti Plsti inset filters Ventilte room Fn Averging Two Sies of the Builing: Some ttis re not suitle s referene euse they hve eve openings only on one sie or they hve only rige openings. In this se, we reommen using referene ox in the tti onnete to extene referene tues. This ox shoul e irtight n mounte in the enter of the tti. It shoul e onnete to two 1 tues tht exten to either sie of the uiling t 25 from the uiling en. Connet the supplie ler tue to the referene sie of the pressure sensor n mke loop lose to the ontroller. Connet the extene referene tue to the ox. Instlling n extene referene tue in the tti inset sreen 1 pipe Air outlet (room) Atti loop to trp humiity Air inlet (referene) Plsti inset filter Ventilte room Averging 2 sies of the uiling Atti 1 pipe 1 pipe Air outlet (room) loop to trp humiity Air inlet (referene) Plsti inset filter Ventilte room CC24-7 ELITE rev.23 9

10 ) Using An Extene Outoor Referene If, for ny reson, the tti fils to meet one or oth of the ove two onitions, or if the uiling oes not hve n tti, you shoul onsier using n outsie referene. A goo ple to strt is on the inlet sie of the room, t minimum istne of 25 feet from ny orner of the uiling to voi win vuum effet. The tue shoul e instlle in ox or restrite spe to voi unesirle sun n win effets. Avoi mounting the ox in the irflow pth into the uiling. Sty t lest 2 feet from the inlet opening. The ox shoul e fille with minerl wool to sor most of the flututions use y the win. Mke t lest thirty holes of ¼ on the sies n ottom of the ox (o not mke holes on the top). Use the ler tue to reh the room n mke moisture trp loop. On the referene sie, use the supplie ler tue, mke loop n join the extene referene tue. The extene referene tue shoul hve igger imeter (1 is goo). Run the extene tue to the lotion of the referene. Mke loop on the wy to trp moisture if unesirle irflows our. This trp shoul inlue plug to rin the wter. Try to run the pipe insie the uiling s muh s possile. Using n extene outoor referene Atti 1 pipe Removle plug Air outlet (room) 2 loop to trp humiity Air inlet (referene) Plsti inset filter Ventilte room 10 CC24-7 ELITE rev.23

11 3. USER INTERFACE 3.1. Lotion of the Controls LED Disply MAIN LCD SCREEN The lrge LCD sreen is use to isply the vrious prmeters n menus. It utomtilly isplys the Current Conitions menu fter 4 minutes of intivity n its ontrst n e moifie in the TRANSFER menu 14). Alrm Log key Shortut keys Ative Alrms Selet Progrm Room Set Point Min Vent Timer Vent Door / Stti Pressure Tunnel Curtin LCD Sreen Sttus LEDs Ajustment uttons Messge Center Arrow keys LED DISPLAY This isply either shows the urrent verge room temperture n/ or the stti pressure level. User-efine shortut key USER DEFINED SHORT-CUT KEY STATUS LEDS The sttus pilot lights inite the urrent sttus of the ifferent stges n outputs. Refer to setion 3.3 for further informtion out these LEDs. ARROW KEYS Use the rrow keys to selet prmeter on sreen. The right n left rrow keys n lso e use to move through the isply y pges in some menus (left=pge-up, right=pge-own). ADJUSTMENT BUTTONS Press + or - to moify the vlue of prmeter. ENTER Press Enter to ess the selete menu. BACK Press BACK to return to the previous menu. SHORTCUT KEYS Press shortut key to ess preefine menu of the ontroller. ALARM LOG Press this key to ess the Alrm Log menu. USER-DEFINED SHORTCUT KEY Press n hol the User-efine shortut key 3 seons to ssoite the selete menu with the shortut key. The estintion of this key n e hnge nytime Sttus LEDs LED ALARM MESSAGE CENTER PROGRAM A-D STAGE 1-16 HEATER 1-8 MEANING Turns on when n lrm onition is etete. Flshes when n lrm onition ourre n ws re-estlishe y itself. Turns on when n messge is signle in the messge log menu. Inites whih sesonl prmeters re urrently in use. Inites whih progrm is urrently in use. Turns on when the selete fn stge is tive. Flshes when one step of the heting output is operting (regulr or high fire step). Turns on when oth steps of the heting output re operting (regulr n high fire steps). Off Time of the minimum ventiltion timer Prmeter Ajustment When prmeter is selete, follow the instrutions isplye t the ottom of the sreen to hnge its vlue. CC24-7 ELITE rev.23 11

12 4. CONTROLLER SETUP 4.1. Time & Dte 23. Controller Setup 4. Time n Dte Time n Dte We Aug 27 20XX 7 : 07 : 07 PM 2. Press Enter to strt eiting the time n te. A pop-up winow for justing the month is isplye. Use the +/- justment uttons to selet n hnge prmeter insie pop-up winow. Do not use the rrow keys for this purpose. 3. Use the +/- justment uttons to selet the urrent month from the srolling list. 4. Press Enter to ontinue. 5. The y is now selete. Press the +/- justment uttons to hnge the urrent y. 6. Press Enter to ontinue. 7. The yer is now selete. Use the +/- justment uttons to hnge the urrent yer. 8. Press Enter to ontinue. A pop-up winow for justing the time is then isplye. 9. Use the +/- justment uttons to set the hours. 10. Press Enter to ontinue. 11. The minutes re now selete. Use the +/- justment uttons to set the minutes. 12. Press Enter to ontinue. 13. The seons re now selete. Use the +/- justment uttons to set the seons. 14. Press Enter to vlite the new time n te Dy / Night Times If night funtions re use, you must speify t wht time the y n night strt n wht is the trnsition time etween oth of them. The trnsition time is the intervl of time over whih the ontroller grully swithes from ytime to nighttime settings. 23. Controller Setup 6. Dy / Night Time* * Aville if night funtions re enle (se. 4.5). Dy Strts At Night Strts At Trnsition Time Dy / Night Time 7:30 A 8:00 P 30 min 2. Set the y n night strt times n the trnsition time etween oth of them Psswor This funtion llows ientifying 2 ifferent types of users. The psswor is me up of 4 igits n it is use to restrit ess to ertin funtions of the ontroller. When orret psswor is entere, the urrent user is ientifie. Instller Psswor (efult = ) The instller moe gives full ess to ll the ontroller funtions. The instller psswor n e moifie s expline elow. User Psswor (efult = & ) The user moe gives ess to the si funtions of the ontroller. The ontroller utomtilly returns to the user moe fter 15 minutes of intivity. The user psswors nnot e moifie. 23. Controller Setup 7. Psswor Current User Psswor Instller Chnge User * * * * Chnge Psswor * * * * Confirm Psswor * * * * Entering psswor: 2. Press Enter to isply the psswor popup winow. 3. Use the +/- justment uttons to enter the first igit of the psswor. Use the +/- justment uttons to selet n hnge prmeter insie pop-up winow. Do not use the rrow keys for this purpose. 4. Press Enter to step to the next igit. 5. Proee the sme wy to enter ll 4 numers. Chnging the instller psswor: To hnge the pssor, enter the instller psswor first s expline ove. The messge Chnge Psswor will then e isplye. Chnge it if require. 12 CC24-7 ELITE rev.23

13 4.3. Controller Progrms & Sesonl Settings Progrms: The ontroller hs 4 progrms of temperture settings. Eh progrm hs its own proe n rely ssignment to run fn stges 1-6 n heting stges (optionl). Using progrms is useful when ifferent setions of the room re oupie in the ourse of th. Refer to setion 4.5 to enle the progrms. Sesons: The temperture t whih fn n ooling stges re tivte n e set seprtely for summer n winter. You must selet the urrent seson s expline elow. Mke sure the right progrm & seson re selete efore justing ny prmeter Seleting Progrm 1. Selet 6. Progrm Seletion or press A Progrm Seletion Copying / Psting Progrm Configurtion Use the opy-pste funtion to uplite the seletion of proes tht re use to mesure the verge room temperture n the seletion of relys (regulr & timer-se relys), n vrile outputs tht re use y fn stges 1 to 6 from progrm onto nother. This vois repeting the sme progrmming sequene severl times. 22. Rely n Proe Assignment 21. Copy Pste * This menu is only essile from the instller moe (se. 4.2). Copy / Pste Selet item to opy: Copy from: Pste to: Confirm? Progrm Progrm A Progrm B No 2. The prompt Selet item to opy is isplye. Choose the Progrm option Mesuring Units 23. Controller Setup 8. Units Unit Seletion Time Moe AM/PM Temperture F Wter gl Stti Pressure WC 2. Selet the proper mesuring units: Time isply AM/PM / 24 hours; Temperture units Celsius (Deg C) or Fhrenheit (Deg F). Wter Gllons / Liters Stti Pressure Inhes of wter ( WC) or Psl (P). Mesuring units re ommon to ll progrms of the ontroller. Running progrm Temperture Settings Progrm A Summer 3. Set the following prmeters: Copy From Selet the soure progrm. The one tht will e uplite. 2. Selet the esire progrm. *Only the progrms tht hve een enle in the instlltion setup re ville (se. 4.5). 3. Selet the urrent seson. The ventiltion, heting n ooling outputs will run oring to the prmeter settings tht re ssoite with this seson. Pste to Selet the trget progrm. The one on whih the opie progrm will e pste. Confirm One ifferent soure n trget progrms re selete, selet Yes to mke the progrm opy. The messge Copy in progress is isplye. Wit until the t trnsfer is over. CC24-7 ELITE rev.23 13

14 4.5. Instlltion Setup The following setion shows how to ustomize the ontroller for your prtiulr pplition. You will lern how to enle your ontroller s inputs n outputs, n how to set other si funtions. Normlly, this setup nees to e one only one. 1. Selet 23. Controller Setup 2. Instlltion* * This menu is only essile from the instller moe (se. 4.2). Instlltion Cler Alrms? No Numer of T Proes 8 Numer of Wter Meters 10 Numer of Relys 40CS Numer of Inlets 10 Numer of Fn Stges 16 Numer of Cooling 4 Numer of Progrms Numer of Light Progrms 8 Numer of Heters 8 Numer of Nturl 2 Numer of Cloks 4 # of Progrm Clok 1 4 # of Progrm Clok 2 4 # of Progrm Clok 3 4 # of Progrm Clok 4 4 Clok 5 Moe Strt/Stop Clok 6 Moe Strt/Run Clok 7 Moe Strt/Rep. Clok 8 Moe Strt/Rep. Clok Inrement 10 min Use Night Set Point? Yes Use Set Point Curve? Yes Use Minimum Vent. Curve? Yes Use Heter Offset Curve? Yes Use Animl Age Funtion? Yes Use Heter Progrms? Yes Use Heter Hi / Lo Yes Use Tunnel? Yes... Exit: Press Bk Chnge: Press +/- Press to selet n item Cler Alrms? Selet Yes to reset the Alrm Log. Numer of Insie T Proes Selet the numer of temperture proes tht re onnete to the ontroller. This prmeter rnges from 1 to 8 proes. Numer of Wter Meters Selet the numer of wter meter tht re onnete to the ontroller. This prmeter rnges from 0 to 10 wter meters. The first 2 wter meters re iretly onnete to the min or of the ontroller; wter meters 8 to 10 re onnete to n externl wter meter moule. Refer to the wiring igrm. Numer of Relys Selet the totl numer of relys provie y the externl rely pnels (10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 16, 32, 48, 64, 40CS, 48CS, 80CS,88CS, 96CS). *Selet the CS option if your rely pnel is omptile with the CS tehnology (urrent sensing relys). Numer of Inlets If the inlets re onnete to externl inlet moules suh s the SB 3000 or SB 3500 moules, speify how mny inlets (or moules) re onnete to the first inlet output. This prmeter rnges from 0 to 10 inlets. *This prmeter is ville if the vent oor moe is set to Ext elow. Numer of Fn Stges Selet the numer of fn stges. This prmeter rnges from 1 to 16 stges. *The minimum numer of fn stge is limite y the stge tht is use to enter in tunnel ventiltion. Refer to setion to selet the first tunnel stge. Numer of Coolings (Mist) Selet the numer of ooling outputs. This prmeter rnges from 0 to 4 outputs. Numer of Progrms Selet the numer of ontroller progrms. This prmeter rnges from 1 to 4 progrms None=1 progrm; =2 progrms; =3 progrms; =4progrms. Numer of Light Progrms Selet the numer of light progrms. This prmeter rnges from 0 to 8 progrms. Numer of Heters Selet the numer of heting stges. This prmeter rnges from 0 to 8 stges. Numer of Nturls Selet the numer of nturl ventiltion zones. This prmeter rnges from 0 to 4 zones. Numer of Cloks Selet the numer of lok outputs. This prmeter rnges from 0 to 8 outputs. # of Progrm Clok x Selet the proper numer of timer progrms use y lok outputs 1-4. This prmeter rnges from 1 to 4 progrms. Clok Moe Selet the operting moe of lok outputs 5 to 8: Strt/Run: the output stops fter userefine run time. Strt/Stop: the output stops t userefine time of the y; Strt/Repet: the lok output opertes oring to timer whih is repete t regulr intervls. Clok Inrement The strt & stop times of lok outputs n either e juste in inrements of 1, 5 or 10 minutes. Selet the esire time inrement. Use Night Set Point? Selet Yes to enle night settings. Use Set Point Curve? Selet Yes to enle urve to get n utomti justment of the set point over time. Use Minimum Vent. Curve? Selet Yes to enle urve to get n utomti justment of the minimum ventiltion fn spee (or fn On Time) over time. Use Heter Offset Curve? Selet Yes to enle urve to get n utomti justment of the heters strt temperture over time. Use Animl Age Funtion? Selet Yes to use funtions tht re se on the ge of the niml ge (urves, light progrms, tunnel urtins, et.) *This prmeter is ville if ll urves re isle ove. Use Heter Progrms? Selet Yes to use seprte het settings for eh progrm (proe n rely ssignment); selet No if these settings re ommon to ll progrms. *This prmeter is ville if heters & progrms re enle ove. Use Heter Lo/Hi Fire? Selet Yes to tivte the heting outputs Lo & Hi fire option. This funtion llows ouling the numer of heters. Refer to se. 7.1 for further informtion. *This prmeter is ville if heters re enle ove. 14 CC24-7 ELITE rev.23

15 Use Tunnel? Selet Yes to enle the tunnel urtin. Tunnel Moe The tunnel urtin opertes oring to the stti pressure level or uses timer? *This prmeter is ville if the stti pressure proe is enle elow. Vent Door Trnsition Selet the trnsition moe etween lterl n tunnel ventiltion *This prmeter is ville if the tunnel urtin is enle n if the vent oor opertion is se on the stti pressure. Open: vent oors fully open t the strtup of the first tunnel stge. As is: vent oors remin in position t the strt-up of the first tunnel stge (only ville if the urtin opertes oring to the stti pressure level). SP: vent oors keep eing ontrolle y the stti pressure level uring the trnsition (only ville if the urtin opertes in timer moe). Tun. PreOpenType Selet t wht moment the tunnel urtin strts eing ontrolle y the stti pressure level: right fter the pre-opening ely (Norml Pre- Opening), or t the strtup of the seon tunnel stge (Tunnel Help moe). In tunnel help moe, the urtin opens uring the preopening ely then remins in position; it strts eing ontrolle y the stti pressure when the following stge strts. *This prmeter is ville if the tunnel urtin s opertion is se on the stti pressure n if the urtin is not use in nturl ventiltion (see elow). Tunnel Pre open Time This ely is use to open the urtin efore tivting the fns when the ontroller enters in tunnel ventiltion. This prmeter rnges from 0 to 60 seons. *This prmeter is ville if the tunnel urtin s opertion is se on the stti pressure n if the urtin is not use in nturl ventiltion (see elow). Mult. Tun. Stg w/ge (Multiple Tunnel Stges with ge) This prmeter limits the use of tunnel stges oring to the niml ge. It llows speifying the mximum tunnel stge tht n e performe t three ifferent ges. *This prmeter is ville if the tunnel urtin n niml ge funtions re enle. Use Tunnel in Nturl? Selet Yes to keep using the tunnel urtin while the ontroller is in nturl ventiltion (se ) Use Stir Fns? Set to Yes to use stir fn relys on stge 1 (se ). Use Vrile? Selet Yes to enle 2 vrile outputs. Vr. 1-2 Minimum Spee Set the solute minimum spee of oth vrile outputs. Use Rmping on Stge 1? This funtion llows to smooth out the trnsition from the minimum ventiltion yles to the full opertion of stge 1. Selet Yes to enle this option. *This prmeter is ville if vrile outputs re isle. Refer to setion for further informtion. Use Rmp. Below SetP With this funtion, the ontroller utomtilly justs the run time of stge 1 fns in minimum ventiltion oring to the outsie temperture: s the wether gets oler, the fn run time ereses grully to ompenste for the hnge. Refer to setion for further informtion. Stge 1 Rmp Dely (Avne) This ely is use when the outsie temperture is greter thn the outsie set point (or if no outsie temperture sensor is use). If the ifferene etween the urrent On Time of stge 1 n the On Time lulte y the rmping lgorithm is greter thn this ely, the On Time eomes the new lulte vlue (se ). *This prmeter is ville from the ftory moe n if vrile outputs re isle. Stge 2 Rmp Dely (Avne) This ely is use when the outsie temperture is lower thn the outsie set point. If the ifferene etween stge 1 s urrent On Time n the lulte On Time vlue is greter thn this ely, the On Time eomes the new lulte vlue (se ). *This prmeter is ville from the ftory moe, if the rmping on stge 1 funtion is enle ove, n if the outsie temperture proe is enle elow. Outsie T Set Point (Avne) The ontroller uses this vlue to lulte the rmping ely (se ). *This prmeter is ville from the ftory moe (eler), if the rmping funtion on stge 1 is enle, n if the outsie temperture sensor is enle elow. Instlltion Use Tunnel? Yes Tunnel Moe Time/SP Vent Door Trnsition Open/SP/As is Tun. PreOpenType TunnelHelp /Norml Tunnel Pre open Time 15 se Mult. Tun. Stg w/ge Yes Use Tunnel In Nturl? Yes Use Stir Fns? Yes Use Vrile? Yes Vr. 1 Minimum Spee 10 % Vr. 2 Minimum Spee 10 % Use Rmping on Stge 1? Yes Use Rmp. Below SetP Yes Stge 1 Rmp Dely 10 se Stge 2 Rmp Dely 10 se Outsie T Set Point 50.0 F Rmping Cyle 5 se Use Outsie Temperture? Yes Use Reltive Humiity? Yes Use Stti Pressure? Yes SP Vent Set 2 None/Stge/T Out Pre-Open Moe Auto/Mn Pre-Open Vent Doors 10 se Pre-Open Atti 10 se SP Tunnel Set 2? None/Stge Exit: Press Bk Chnge: Press +/- Press to selet n item Rmping Cyle (Avne) Frequeny t whih the rmping yle is lulte (se ). *This prmeter is ville from the ftory moe (eler), n if the rmping funtion on stge 1 is enle ove. Use Outsie Temperture? Selet Yes if n outsie temperture proe is onnete to the ontroller. Use Reltive Humiity?: Selet Yes if humiity sensor is onnete to the ontroller. Use Stti Pressure? Selet Yes if stti pressure (SP) sensor is onnete to the ontroller. SP Vent Set 2 Selet t wht moment the seon set of pressure set points strt eing use for the opertion of vent oors: Selet Stge to strt using the seon group of set points t the strtup of speifi fn stge; selet Out T to strt using it s the outsie temperture ereses; selet None to isle this funtion. Refer to setion for further informtion.*this prmeter is ville if the tunnel urtin opertes oring to the stti pressure. CC24-7 ELITE rev.23 15

16 Instlltion SP Tunnel Set 2? None/Stge Use SP Comp. on Inlets? Yes Sen temp. Comp. eh 2:00 (m:s) Use Curve on Low SP Alrm? Yes Monitor Breker Temp.? Yes Vent Door Moe SP/Time/Ext Use 2n Inlet? Atti/2n inlet/none Atti moe Time/SP 2n Inlet type Siewll/Tunnel 2n Inlet moe Time/SP Atti/2n Inlet Proe Room/Iniv Shown on LED Disply Stti Pressure? Yes Vent Door Position? Yes Exit: Press Bk Chnge: Press +/- Press to selet n item Pre-Open Moe In minimum ventiltion, the ontroller slightly opens the vent oors efore tivting the fns. Selet Auto to use n utomti pre-opening ely or selet Mn to set this ely. *This funtion only pplies to the vent oor outputs; it oes not pply to the tti vent. Pre-Open Vent Doors The pre-opening of vent oors n e juste from 0 to 60 seons. *This prmeter is ville if the pre-opening moe is set to Mn ove. Pre-Open Atti The pre-opening of the tti vent rnges from 0 to 60 seons. *This prmeter is ville if the seon inlet is use s n tti vent (see elow). SP Tunnel Set 2? Selet Stge if the tunnel urtin strts using seon group of stti pressure set points t the strt-up of speifi ventiltion stge; selet None if the tunnel urtin oes not use 2n group of pressure settings. *This prmeter is ville if the tunnel opertes oring to the stti pressure. Refer to setion for further informtion. Use SP Comp. on Inlets? Selet Yes for the ontroller to just the opening of the ir inlets when the stti pressure level gets out of rnge. *This prmeter is ville if n ir inlet n the stti pressure sensor re enle ove. To enle n ir inlet, set the Vent Door Moe to Ext elow n then enle the proper numer of inlets ove. Sen Temperture Compenstion eh If temperture ompenstion hs to e pplie on the position of the ir inlets, the ontroller only sens ompenstion request of 1% t time. Speify the frequeny t whih 1% ompenstion must e pplie on the position of the inlets. This prmeter prevents moving the ir inlets too muh in short perio of time (refer to setion for further informtion on this ompenstion). *This prmeter is essile if n ir inlet is enle ove ( Vent Door Moe is set to Ext elow n numer of inlets is greter thn 1 ove). Use Curve on Low Stti Pressure (SP) Alrms? The ontroller n utomtilly hnge the low stti pressure lrm limit with time. With the low SP lrm urve, you n progrm 3 ifferent low pressure lrm limits n the moment t whih eh limit strts eing use is efine s funtion of the niml ge. Selet Yes to enle the low SP lrm urve or selet No to isle this urve. Monitor Breker Temp.? Selet Yes to monitor the temperture of the min reker. When this funtion is enle, the ontroller souns n lrm if the temperture of the sensor lote ner the reker gets too high. Instll the reker s proe lose to the reker ox, not insie the ox! Vent Door Moe Selet the proper operting moe of the first ir inlet output. SP: Selet SP if the first inlet output is use to ontrol pressure-se vent oors. Time: Selet Time if the first inlet output is use to ontrol timer-se vent oors tht re using the uilt-in timer of the ontroller. DO NOT selet this option if the vents re using the timer of n externl SB3500 moule: in this prtiulr se, selet the Ext option to enle the externl moule. Ext: Selet Ext if the first inlet output is use to onnet externl ir inlet moules suh s SB3000 potentiometer feek moules or SB3500 timerse inlet moules. *Up to 10 SB moules n e onnete to the first inlet output. Go k to the top of the instlltion menu so set the numer of moules properly ( Numer of Inlets prmeter). Use 2n Inlet? In orer to enle the seon inlet output, selet the prtiulr funtion of this output: it n either e use to ontrol n tti vent (selet Atti ), or it n e use s supplementry tunnel urtin or vent oor output (in oth ses, selet 2n Inlet ). Atti Moe Speify the operting moe of the tti vent: selet SP if it moves oring to the level of stti pressure or selet Time if it moves oring to timer. *This prmeter is essile if the seon inlet output is use to ontrol n tti vent n if the stti pressure sensor is enle ove. 2n Inlet Type If the seon inlet oes not ontrol n tti vent, selet its prtiulr funtion: tunnel urtin or siewll (siewll = vent oor). *This prmeter is essile if the seon inlet output oes not ontrol n tti vent. 2n Inlet Moe Speify the operting moe of the seon inlet: selet SP if it moves oring to the level of stti pressure or selet Time if it moves oring to timer. *This prmeter is essile if the seon inlet output oes not ontrol n tti vent n if the stti pressure sensor is enle ove. Atti/2n Inlet Proe The ontroller llows you to speify the temperture proe tht is use y the seon ir inlet output. Selet Room if the output refers to the room temperture or selet Iniv to speify prtiulr proe in the Proe Assignment menu. *Note tht this prmeter is isplye for onsulttion purpose only. It hs no effet on the wy the 2 n inlet opertes. Shown on LED Disply The re LED isply is use to show the room temperture. You n lso hoose to isply the room temperture long with the stti pressure level n/ or the vent oor position. *Note tht the stti pressure level n only e shown if the SP sensor is enle ove n the vent oor position n only e shown when using timer-se vent oors. 16 CC24-7 ELITE rev.23

17 4.6. Proe Settings Proe Assignment Priniple of Opertion: This setion explin how to selet temperture proes tht re use to mesure the room temperture n how to ssign temperture proes tht re use to ontrol/ monitor the outputs of the ontroller. Worksheets re ville t the en of this mnul to write own your seletion of sensors. 22. Rely n Proe Assignment* 2. Selet the esire proe ssignment menu: 12. Proes for Stges 13. Proes for Heters 14. Proes for Coolings 15. Proes for Nturls 16. Proes for Inlets 17. Proes for 0-10V Outputs 18. Proes for Min Breker 19. Proes for Vent Door Proes for Atti/2n Inlet** *This menu is only essile from the instller moe (se. 4.2). ** This menu is essile if the Atti / Ven Doors Proes prmeter is set to Iniv. in the instlltion menu (se. 4.5). Cooling Proe Assignment Show Proes of : Cooling Depening on the hosen output, ssign the temperture proes s follows: Proes for Stges (or Room Temperture) All fn stges operte oring to the verge temperture in the room. Selet wht proes re use to mesure the verge room temperture. *Mke this proe ssignment seprtely for eh progrm in use (if pplile). Proes for Heters Eh heting output opertes oring to the verge temperture reing of hosen temperture proe set. Selet wht proes re use to ontrol eh one of them (regulr & Hi Fire heting stges). *Mke this proe ssignment seprtely for eh progrm in use (if pplile) Proes for Cooling Outputs Eh ooling output opertes oring to the verge temperture of hosen temperture proe set. Selet wht proes re use to ontrol eh one of them. Note tht the outsie temperture proe (proe 0) n lso e prt of the verge temperture. Tht is to mke sure the outsie temperture is suffiient to permit the tivtion of the ooling output. *This prmeter is ville if ooling outputs re enle in the instlltion setup (se. 4.5). Proes for Nturls Speify whih temperture proes re lote in eh nturl ventiltion zone. When the ontroller opertes in nturl ventiltion, the nturl urtin will move s funtion of the mient temperture of its respetive zone. Note tht the outsie temperture proe (proe 0) n lso e prt of the verge temperture of zone. Tht is to mke sure the outsie temperture is suffiient to permit the opening of the nturl urtin. Proes for Nturl Assign temperture proes to eh nturl zone (proe 0 refers to the outsie temperture proe). *This prmeter is ville if nturl zones re enle in the instlltion setup (se. 4.5). Proes for Inlets Eh inlet tht is onnete to SB moule opertes oring to the verge reing of hosen temperture proes. Selet wht proes re use to ontrol eh one of them. *This prmeter is ville if inlets re enle in the instlltion setup (se. 4.5). 0-10V Outputs Eh 0-10V output tht is use for ooling or heting opertes oring to the verge temperture reing of hosen temperture proe set. Selet wht proes re use to ontrol eh one of them. Min Breker Proes A proe n e use to monitor the temperture of the min reker so tht the ontroller n soun n lrm if the reker s temperture gets too high. Selet whih proe is use for this purpose. Proes for Atti/2n Inlet If the seon ir inlet output uses prtiulr temperture proes, plese selet them in this tle. *Note tht this seletion of proe is me for onsulttion purpose only. It hs no effet on the wy the 2 n inlet opertes. Proes for Vent Door 1 If the first vent oor output uses prtiulr temperture proes, plese selet them in this tle. *Note tht this seletion of proe is me for onsulttion purpose only. It hs no effet on the wy the vent oor opertes Proe & Wter Meter Clirtion You n slightly just the reing of eh proe input in orer to otin urte n uniform reings from ll proes. In ition, if wter meter is use, you must lirte its wter flow rte. 23. Controller Setup 3. Proe Clirtion* * This menu is only essile from the instller moe (se. 4.2). Proe Clirtions Insie Temp. Proe F Insie Temp. Proe F Insie Temp. Proe F Outsie Temperture 0.0 F Reltive Humiity 0 % Stti Pressure.000 WC Wter Meter 1 1 gl/p Wter Meter 2 1 gl/p 2. Ajust the reing of the proes (if require). Insie Temperture Proe The reing of the insie n outsie temperture sensors n juste of ±5 F (±2.3 C). Reltive Humiity Proe The reing of the humiity sensor n juste of ±3%. Stti Pressure (SP) Proe The reing of the stti pressure proe n juste of ± WC (±7P). Wter Meters Set the wter flow per pulse of eh wter meter. This prmeter rnges from 1 to 100 gllons (or liters) per pulse. CC24-7 ELITE rev.23 17

18 4.7. Rely Assignment Priniple of Opertion RELAY PANELS: Externl rely pnels n e onnete to the ontroller. In ll, the ontroller n monitor up to 100 externl On/ Off relys n 2 vrile outputs. The following proeure shows how to link up the relys with the vrious stges n outputs. Refer to the wiring igrm enlose with this mnul to onnet the rely pnels to the ontroller n to wire the los. Note tht the rely ssignment n only e one from the instller moe Worksheets re ville the en of this mnul to write own your rely ssignment settings. Use the rrow keys to nvigte through the rely ssignment winow Heters Rely Assignment Assign relys to ll heting outputs n to ll hi fire heting outputs (if pplile). If heter progrms re enle in setion 4.5, mke the rely ssignment seprtely for eh progrm in use. 22. Rely n Proe Assignment* 2. Relys for Heters** * This menu is only essile from the instller moe (se. 4.2). ** This menu is essile if heters re enle (se. 4.5). Heter Rely Assignment Selet the proper heting output mongst the ones tht hve previously een enle (se. 4.5). 3. Put hek mrk to ssign rely Fn Stge Rely Assignment This setion shows how to ssign relys to fn stges, how to use vrile outputs, n how to enle stir fns n timer-se relys in the stges Ventiltion Relys : Priniple of Opertion TIMER-BASED RELAYS ON FAN STAGES Timer-se relys run oring to timer s long s their ssoite fn stge is on. They re useful to run evies tht nee to follow the sme progression s fn stges in timer moe. Setion shows how to tivte timer-se relys n setion shows how to set the timer. STIR FAN RELAYS ON FAN STAGE 1: Stir fn relys of stge 1 run ontinuously in minimum ventiltion n uring stge 1. Using this type of rely llows tivting stir fn outputs without interruption while minimum ventiltion yles re performe. VARIABLE OUTPUTS: Eh fn stge n use two vrile fn outputs. Speify the operting moe of the vrile outputs for eh fn stges s follows: Vr.: When the fn stge strts, the vrile outputs strts t its minimum intensity then grully inreses in spee s the fn stge progresses. ON: The vrile output ts s n ON/ OFF output: it is tivte t its full pity when its ssoite fn stge is on. OFF: The vrile output is not tivte Fn Stge Rely Settings Selet the relys ssoite with eh fn stge: 1. Selet 22. Rely n Proe Assignment* 1. Relys for Stges ** * This menu is only essile from the instller moe (se. 4.2). ** Refer to the previous setion to get further informtion out these prmeters. Stge Rely Assignment Show Rely of : Stge Selet fn stge. 3. Mke the rely ssignment for the selete stge: put hek mrk to ssign n On/Off rely, selet TMR to ssign timer-se rely, STR to ssign stir fn rely. YOU MUST ASSIGN RELAY(S) TO ALL FAN STAGES IN USE! An lrm sets off when fn stge tht oes not tivte ny rely is tivte (this is true exept for nturl ventiltion stges n for vrile stges 1 n 2). When this type of lrm ours, the ontroller keeps using the relys of the previous fn stge. Timer-se relys re use to tivte misting units. If ooling units re progrmme to stop when the humiity level gets too high, timer-se relys will lso stop running (exept if the ontroller is in minimum ventiltion. Refer to setion 10.2 for further informtion out the mist shutoff option. The rely ssignment for fn stges 1 to 6 must e one seprtely for eh progrm in use. Press A to selet progrm. 18 CC24-7 ELITE rev.23

19 Vrile Outputs & Timer Settings The following proeure shows how to enle vrile outputs within fn stges. It lso emonstrtes how to just the On n Off times of fn stges timer-se relys. 22. Rely n Proe Assignment* 10. Rely Timer/Vrile Settings** * This menu is only essile from the instller moe (se. 4.2). ** See se for further informtion. Rely Timer n Vrile Settings Show Settings of Stge 1 Vrile 1 Vrile 2 Rely Timer Moe Rely On Time Rely Off Time 2. Selet fn stge. Off Off Se 15 se 0 se Vrile 1-2 Set the sttus of oth vrile outputs uring the selete fn stge (On, Vr. or Off). *This prmeter is ville if vrile outputs re enle (se. 4.5). Rely Timer Moe Selet whether the relys timer is set in seons (0 to 900 seons) or in hours (0 to 9:00 hh:mm). Relys On Time This is the run time of timer-se relys for the selete fn stge. This prmeter rnges from 0 to 900 seons (or 0 to 9:00 hh:mm). Relys Off Time This is the ile time of timer-se relys for the selete fn stge. This prmeter rnges from 0 to 900 seons (0 to 9:00 hh:mm). The sttus of the vrile output n the timer of fn stges 1 to 6 must e set seprtely for eh progrm in use. Press A to selet progrm. YOU MUST ASSIGN RELAY(S) TO ALL FAN STAGES IN USE! An lrm sets off whenever fn stge tht oes not tivte ny rely is tivte. When this sitution ours, the ontroller keeps using the relys of the previous fn stge Copying / Psting Fn Stge Relys It is possile to uplite the rely seletion of fn stge onto nother stge y using the opy n pste funtion. This vois repeting the sme progrmming sequene severl times. 22. Rely n Proe Assignment* 21. Copy Pste * This menu is only essile from the instller moe (se. 4.2). Rely Timer n Vrile Settings Selet item to opy: Stg Rely Copy from: Stge 1 Pste to: Stge 2 Confirm? No 2. Set the following prmeters: Selet item to opy Selet the Stg Rely option. Copy From This is the soure fn stge. The one tht will e uplite. Pste to This is the trget fn stge. The one on whih the opie relys will e pste. 3. One the soure n the trget stges hve oth een efine, the messge Confirm? ppers on the isply. Selet Yes to onfirm the stge relys uplition. The messge Copy in progress... plese wit.. is isplye. Wit until the uplition proess is over Curtin, Vent Door & Atti Relys Assign n opening n losing rely to eh output tht uses n tutor (nturl ventiltion urtin, vent oors, 2n ir inlet output & tunnel urtin). Connet these outputs to the relys tht hve een esigne for this purpose on the rely pnels (Open/ Off/Close rely). 22. Rely n Proe Assignment* 2. Selet the rely ssignment menu **: 3. Tunnel Curtin 4. Vent Door 5. Atti/2n Inlet (for the 2n tunnel urtin, 2n siewll vent or for the tti vent) 9. Nturl * This menu is only essile from the instller moe (s.4.2). ** Only the outputs tht re enle in the instlltion menu re ville (se. 4.5). Tunnel Door Rely Assignment Show Relys of : Open Door Selet the output s opening rely n then put hek mrk to ssign the opening rely. 4. Selet the output s losing rely n then put hek mrk to ssign the losing rely. CC24-7 ELITE rev.23 19

20 Clok Output Relys The following proeure shows how to ssign lok outputs relys. It lso explins the priniple of opertion of the ommon relys. Common Relys: It is possile to mth the tivtion of some outputs with the tivtion of lok outputs; i.e. ll outputs tht shre ommon rely must e tivte simultneously for the rely to swith. This funtion my e use to etivte n output uring night or on speifi ys of the week for instne. Devies tht shre ommon relys with lok outputs re thus stoppe when the lok output is off. This is true for ll type of outputs exept for fn stges n ooling outputs: these outputs relys re not ffete y ommon relys. Exmple of how to etivte n output uring night: 1. Heter 4 uses rely 6; 2. Rely 6 is lso use y lok output 1 n is ommon rely. 3. Clok output 1 is isle uring night. Result : Heter 4 opertes normlly s long s lok output 1 is tive ut nnot e enle uring night while the lok output is off Clok Output Relys Selet the relys tht re ssoite with eh lok output. 22. Rely n Proe Assignment* 6. Relys for Cloks** 1. Rely Assignment * This menu is only essile from the instller moe (se. 4.2). ** Aville if lok outputs re enle (se. 4.5). Clok Rely Assignment Show Relys of : Clok Selet lok output. 3. Put hek mrk to ssign rely Seleting Common Relys When ommon rely is ssigne to lok output n to ny other output, ll outputs tht use tht sme rely must e tivte simultneously for the rely to swith (exept for fn stge n ooling output relys). 22. Rely n Proe Assignment* 6. Relys for Cloks** 2. Common Relys * This menu is only essile from the instller moe (s.4.2). ** Aville if lok outputs re enle (se. 4.5). Common Rely Put hek mrk to ientify ommon rely Cooling Output Relys Selet the relys tht re ssoite with eh tivte ooling output s follows: 22. Rely n Proe Assignment* 7. Relys for Cooling** * This menu is only essile from the instller moe (se. 4.2). * This menu is essile if ooling outputs re enle (se. 4.5). 2. Selet ooling output. 3. Put hek mrk to ssign rely Bkup Box Rely Selet the kup ox rely. This normlly lose rely opens when ontroller or power filure ours. 22. Rely n Proe Assignment* 8. Relys for Bkup * This menu is only essile from the instller moe (se. 4.2). 2. Put hek mrk to ssign rely Feeer Rely Feeer relys re normlly lose ontt. This ontt opens when feeer run time lrm ours, using the stop of the feeer s motor. 22. Rely n Proe Assignment* 11. Relys for Feeer * This menu is only essile from the instller moe (se. 4.2). 2. Put hek mrk to ssign rely. 20 CC24-7 ELITE rev.23

21 4.8. Test Moe The test moe is use to simulte temperture n stti pressure hnges to verify the ontroller s performne. The temperture proe n stti pressure inputs re turne off while the test moe is on. This moe is utomtilly etivte fter 15 minutes of intivity or when you isle it. 23. Controller Setup 9. Test Moe Test Moe 4.9. Version This menu shows your ontroller s version numer. This piee of informtion is useful to get tehnil support. 23. Controller Setup 10. Version SETTINGS Core CC24-7 Elite Dte V X.X V X.Xx Test Moe Sttus Off Temperture 77.9 F Stti Pressure.080 WC 2. Set the following prmeters: Test Moe Sttus Selet Yes to enle the test moe, selet No to exit from the test moe. Temperture Enter the simulte room temperture. *This prmeter n only e hnge if the test moe sttus is enle ove. Stti Pressure This is the urrent stti pressure level in the room. This vlue is shown s referene only; it nnot e moifie. *This prmeter is only shown if the stti pressure sensor is enle (se. 4.5). CC24-7 ELITE rev.23 21

22 5. TEMPERATURE SETTINGS 5.1. Temperture Set Point The set point is trget temperture; the tivtion n etivtion of the vrious stges is se on this referene temperture. NIGHT SET POINT: A night set point n e enle to lower the trget room temperture uring night. This set point is reltive to the regulr temperture set point, whih mens tht if the regulr set point hnges with time, the night set point is juste oringly. To use night set point, enle the night set point funtion in the instlltion in setion 4.5 n set the time t whih the night egins in setion SET POINT CURVES: Use temperture urve to get n utomti justment of the set points over given perio of time. The trget temperture is thus lwys pte to the nimls nees s they grow. Refer to setion for further informtion out the urves Set Point Settings 7. Temperture Set Point or press B. The set points n only e moifie while the urve is off. Curve Sttus Temperture Set Point Off Temperture Set Point 80.0 F Night Temp. Set Point 80.0 F 2. Set the following prmeters: Curve Sttus Shows the urrent sttus of the set point urve. This piee of informtion nnot e moifie. Refer to setion to moify the urve sttus. *This prmeter is ville if the set point urve option is enle (se. 4.5). Temperture Set Point This prmeter rnges from -40 F to 100 F (-40.0 C to 37.8 C). *Cn only e moifie when the urve sttus is Off (se ) Set Point Curve The set point urve llows n utomti justment of the trget room temperture over time. The set point hnges using 10 steps. Eh step speifies y numer n trget temperture for tht y. These steps re se on the niml ge. One ll steps re efine, the urve must e tivte. The ontroller then strts hnging the temperture set point every hour in liner fshion etween onseutive steps of the urve. When the lst step is rehe, the temperture set point for tht y is mintine until new niml th strts n until the niml ge is reset. Set Point Curve Set Point Dy Night Set Point This prmeter rnges from -40 F to 100 F (-40.0 C to 37.8 C). *This prmeter is ville if the night set point funtion is enle (se. 4.5). This vlue n only e moifie while the urve sttus is Off (se ). Night set point: If night set point is use, the set point urve stops eing use uring night. NOTE: Certin restritions pply to reue the risk of errors: - The highest possile y numer is Deresing y numers is not llowe. - All ten steps must e speifie. If you on t nee ten ifferent steps, repet the lst temperture for eh unneessry step. 22 CC24-7 ELITE rev.23

23 9. Curve Settings* 1. Temperture Set Point * This menu is essile if the set point urve option is enle in setion 4.5. Temperture Set Point Curve Set Point 70.0 F y F y F y F y F y F y F y F y F y F y F Curve Sttus: Off Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: The urve steps n only e moifie while the urve is isle. Dy Numer Set the y for eh of the 10 steps. This numer orrespons to the niml ge n is justle from -5 to 450 ys. Negtive vlues re use to prepre the house efore the letting the nimls enter the uiling. *Cn only e moifie while the urve is isle. Temperture Set the temperture ssoite with eh step of the urve. *Cn only e moifie while the urve is isle. Curve Sttus Selet Yes to tivte the urve. One it is enle, the set point utomtilly eomes juste etween onseutive points of the urve; for this reson, the set point n urve steps nnot e moifie while the urve is on. 6. VENTILATION & COOLING 6.1. Minimum Ventiltion Minimum Ventiltion Cyles Priniple of Opertion Minimum ventiltion yles re use elow fn stge 1. Running the fns even though ventiltion is not require for reuing the room temperture is useful to reue the humiity level n supply oxygen to the room. It lso prevents the fns from freezing in winter. If vrile fn outputs re enle, the ontroller tivtes these fns t user-efine spee uring the minimum ventiltion yles; if they re not use, the ontroller then uses stge 1 fns. Minimum Ventiltion Timer: The minimum ventiltion timer is ompose of n On Time n of Cyle Time. The fns run uring the On Time n then stop until the en of the Cyle Time. Min.Vent Fn Sttus ON OFF Minimum Ventiltion Timer ON Time Cyle Time Time Stir Fns In Minimum Ventiltion: Stir fn relys of stge 1 run ontinuously uring the minimum ventiltion yles n on stge 1. This llows ypssing the minimum ventiltion s timer. Refer to setion to use this feture Settings WITH VARIABLE OUTPUTS: 8. Minimum Ventiltion or press C Test Moe Vrile 1 Curve Off Sttus On On Time 15 se Off Time 15 se Minimum Spee 30 % Vrile 2 Curve Off Sttus On On Time 15 se Off Time 15 se Minimum Spee 30 % 2. Set the following prmeters: Curve Sttus The minimum ventiltion urve sttus is isplye ut nnot e moifie. Refer to setion to moify it. On / Off Times Set the minimum ventiltion timer s On n Off times of oth vrile outputs. This prmeter rnges from 0 to 900 seons. Minimum Spees Set the spee of oth vrile outputs tht is use in minimum ventiltion. *Cn only e moifie if the urve is isle (se ). WITHOUT VARIABLE OUTPUTS: 8. Minimum Ventiltion or press C Minimum Ventiltion Minimum Ventiltion Curve Minimum Vent. On Time Minimum Vent. Cyle Time Clulte On Time 2. Set the following prmeters: Off 30 se 60 se 30 se On / Cyle Times Set the On & Cyle times of the minimum ventiltion timer. These prmeters rnge from 0 to 900 seons. *The yle time is limite y the pre-opening ely of the ir intke tht is use in minimum ventiltion (tti vent or vent oor); it must e greter thn twie pre- opening ely + 10 seons (s.4.5). In ition, the yle time must e greter thn the On Time. Finlly, note tht these prmeters n only e moifie if the urve is isle (se ). Clulte On Time If the minimum ventiltion urve is enle, the fns on time in minimum ventiltion is utomtilly juste over time. The lulte On Time is the urrent On Time, s efine y the urve. *This vlue nnot e moifie. CC24-7 ELITE rev.23 23

24 Minimum Ventiltion Curve Priniple of Opertion If Vrile Outputs re use: If vrilespee fns re use in minimum ventiltion, the ontroller n utomtilly inrese the minimum ventiltion spee over time with urve. The spee urve must e efine seprtely for eh vrile-spee fn. Without Vrile Outputs: If On/Off fns re use in minimum ventiltion, the ontroller n utomtilly inrese the On Time portion of the minimum ventiltion yle with time. Curve efinition: A urve is ompose of 10 steps. Eh step speifies y numer n minimum ventiltion spee (or On Time ) for tht y (the y numer refers to the niml ge). When the urve is tivte, the ontroller hnges the minimum ventiltion spee (or On Time ) every hour in liner fshion etween onseutive steps of the urve. When the lst step is rehe, the ontroller keeps using the spee (or On Time ) ssoite to tht y. Min Vent. Spee (or On Time) Min. Ventiltion Curve DAYS Notes: Certin restritions pply to reue the risk of errors: 1. The highest possile y numer is Deresing y numers is not llowe. 3. All ten steps must e speifie. If you on t nee 10 ifferent steps, repet the lst spee (or On Time ) for eh unneessry step Min Vent. Curve Settings WITH VARIABLE OUTPUTS: 9. Curve Settings 2. or 3. Vrile 1 or 2* * This menu is essile if the minimum ventiltion urve n vrile outputs re enle (se. 4.5). * Only the vrile outputs tht re use in minimum ventiltion re ville (se ). Minimum Ventiltion Vrile 1 Curve Spee 30 % y 1 10 % y % y % y % y % y % y % y % y % y % Curve Sttus Off Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: The urve steps n only e moifie while the urve is isle. Dy Numer Set the y for eh of the 10 steps. This y numer orrespons to the niml ge, n is justle from -5 to 450 ys. Negtive vlues re use to prepre the house efore the nimls rrivl. *Cn only e moifie while the urve is isle. Spee Set the fn spee ssoite with eh step of the urve. *Cn only e moifie while the urve is isle. Curve Sttus Selet Yes to tivte the minimum ventiltion spee urve. One it is enle, the minimum ventiltion fn spee is utomtilly juste etween onseutive steps of the urve; for this reson, these steps nnot e moifie while the urve is on. WITHOUT VARIABLE OUTPUTS: 9. Curve Settings 2. Minimum Vent. On Time Curve * This menu is essile if vrile outputs re isle (se. 4.5). 2. Set the following prmeters: The urve steps n only e moifie while the urve is isle. Dy Numer Set the y for eh of the 10 steps. This y numer orrespons to the niml ge, n is justle from -5 to 450 ys. Negtive vlues re use to prepre the house efore the nimls rrivl. *Cn only e moifie while the urve is isle. On Time Set the On Time of the minimum ventiltion yles for eh step of the urve. *Cn only e moifie while the urve is isle. Curve Sttus Selet Yes to tivte the minimum ventiltion urve. One it is enle, the running time of the fns, uring the minimum ventiltion, is utomtilly juste etween onseutive steps of the urve; for this reson, these steps nnot e moifie while the urve is on. 24 CC24-7 ELITE rev.23

25 Min Vent. Rmp & Compenstion Stge 1 On Time Rmp The ontroller hs rmping funtion to smooth out the trnsition from minimum ventiltion to the full opertion of the stge 1 fns; the fns running time n e utomtilly juste to hieve grul inrese or erese in the ventiltion level. This funtion is use when stge 1 oes not use vrile fns. When the room temperture is t or elow the set point, the fns of stge 1 operte oring to the minimum ventiltion yles. When the room temperture inreses ove the set point, new On Time is lulte perioilly s the temperture inreses to llow smooth progression (from point A to point B) up to full opertion of the fns when the strt temperture of stge 1 is rehe. If the room temperture ereses to stge 1 s stop temperture, the ON TIME vlue of the minimum ventiltion yle ereses grully from vlue equl to the totl yle time (point C) to the vlue efine y the rmping funtion. Run Time Stge 1 On Time Rmp On Time Compenstion Below the Set Point The ontroller hs the pility of utomtilly justing the running time of the minimum ventiltion fns s funtion of outsie temperture. As the wether gets oler, the on time is erese grully to ompenste for the hnge. This n help reue osts y reuing the ventiltion when it is not require. A urve is use to lulte the require ompenstion s perentge of urrent on time (see grph elow). Only the running time is juste; the totl yle time remins unhnge. Exmple: In the first exmple, ompenstion is not neee when the outsie temperture is greter thn 50 F. The fns operte oring to their full running time. In the seon exmple, the running time is erese to 66.5% to ompenste for the oler outoor temperture. The yle time remins unhnge. Compenstion Rte (%) Min.Vent Fn Sttus ON OFF Min.Vent Fn Sttus ON OFF Minimum Ventiltion Compenstion Exmple of the On Time Compenstion Temperture > 50 F Compenstion = 100% ON Time Cyle Time Temperture > 25 F Compenstion = 66.5 % ON Time Cyle Time Time Time On Time = Cyle Time C B On Time A OFF MinV. Set Point Stge 1 Stop T Stge 1 Strt T Stge 2Strt T Room T The ontroller uses two user-efine rmping elys to etermine when to just the rmping yle. Rmping ely 1 is use when the outsie temperture is greter thn the outsie set point (it is lso use permnently if no outsie temperture proe is use); rmping ely 2 is use when the outsie temperture is elow the outsie set point. If the ifferene etween the urrent on time vlue n the on time vlue lulte y the rmping lgorithm is greter thn the rmping ely, the on time vlue eomes the lulte vlue. Outsie T CC24-7 ELITE rev.23 25

26 6.2. Fn Stges Priniple of Opertion On/Off Fn Stges The ontroller hs 16 On/Off fn stges whih operte in sequene to inrese the level of ventiltion s the room temperture inreses. Eh stge n tivte two vrile outputs n omintion of timer relys for ooling purposes. A fn stge is tivte when the room temperture rehes its strt temperture; it is isle when the room temperture ereses to its stop temperture. Ventiltion Level Operting Digrm of Fn Stges Timer Relys for Cooling Devies: Fn stges n tivte relys tht will run in timer moe. This option n e use to tivte ny kin of evie tht nees to follow the sme progression s ventiltion stges. The timer is me of n On Time n n Off Time. Refer to setion to tivte timer-se relys. Fn Sttus ON OFF Fn Stge Timer On Time Off Time Time Fn Spee 100% Min Spee Set Point Operting Digrm of Vrile-Spee Fns Stge x Stop T Stge x Strt T Stge x+1 Strt T Room T Stg y Stg x Set Point Stge x Stop T Stge x Strt T Stge y Stop T Stge y Strt T Room T Fn stges strt tempertures re efine with respet to the set point n with respet to eh other. This mens tht when one of these vlues is juste, ll the onseutive vlues re juste y the sme mount. For exmple, if the set point is inrese y 1 F, the strt temperture of ll fn stges will e inrese y the sme mount. The strt n stop tempertures of ll fn stges must e set seprtely for summer n winter. Press A to selet seson Vrile Outputs Vrile outputs re tivte when their ssoite fn stge strts (se. 4.7). They re enle t their minimum spee, s efine in setion 4.4, n grully inrese in spee s the room temperture inreses. They reh their full spee when the strt temperture of the following fn stge is ttine. Min spee stge 2 Spee of vrile fns Min spee 100% Trnsition etween fn stges 1 n 2 : If the next stge is n ON/OFF fn stge, the vrile output is etivte when the new stge strts. If the next stge is nother VARIABLE fn stge, the spee of the first vrile fn stge is reue to minimum when the seon vrile fn stge strts. This llows smooth trnsition etween oth stges. The grph elow sums up the sitution: Trnsition etween Stges 1 & 2 Bnwith 0.3 F Off Room T Bnwith Stge 1 Strt T Stge 2 Stop T Stge 2 Strt T 26 CC24-7 ELITE rev.23

27 * Strting Spee: The vrile outputs use in VAR (vrile) in stge 1 or 2 strt t the sme spee s efine for the minimum ventiltion yles (se ). The vrile outputs use in VAR (vrile) within Stge 3 n higher strt t their solute minimum spee (s efine in setion 4.5). The nwith efines the intervl over whih the vrile output goes from its minimum to its full spee. This is true even if full spee is never rehe s in the exmple ove. When the strt temperture of stge 2 is rehe, the vrile output ereses to its minimum spee. V1 nwith is then use to inrese the fn spee s the temperture inreses. When the temperture ereses elow stge 2 s strt temperture, the minimum fn spee is mintine until the stge s stop temperture is rehe. The lst fn stge must not e onfigure in vrile moe. If the lst fn stge uses vrile output, it must e use s n on/off output (se. 4.7) V Ventiltion Output The ontroller hs four 0-10V outputs to ontrol supplementry vrile fn stges, lights, or heting evies. The following proeure shows how to use 0-10V outputs for the tivtion of inepenent vrile fns. This setion explins how 0-10V ventiltion outputs work. At n elow the Stop T : The output is etivte. At the Strt T : The output opertes ontinuously t its minimum spee, n strts inresing in spee s the temperture inreses; At Strt T + Bnwith: The fns reh their mximum spee; Intensity Mx Min 0-10V Ventiltion Output Settings Fn Stge Settings If sesonl settings re use, set the fn stge prmeters seprtely for oth sesons. Press A to selet seson. 14. Fn/Cool./Nt. Temp. Settings 1. Fn Temperture Settings Fn Temperture Settings Current Temp. Set Point 80.0 F Stge 1 Strt Temperture 80.5 F Stop Temperture 80.0 F V1 Bnwith 2.0 F V2 Bnwith 2.0 F Stge 2 Strt Temperture 80.5 F Stop Temperture 80.0 F V1 Bnwith 2.0 F V2 Bnwith 2.0 F Stge 3 Strt Temperture 81.0 F Stop Temperture 80.5 F... Stge 16 Strt Temperture 81.0 F Stop Temperture 80.5 F Exit: Press Bk Chnge: Press +/- Press to selet n item OFF Stop T Strt T Bnwith Room T 2. Set the following prmeters: Refer to setion for further informtion on these prmeters. Current Temp. Set Point This is the urrent temperture set point. It is isplye for onsulttion only n nnot e moifie. *Refer to setion 5.1 for further informtion. Strt & Stop Tempertures Set the strt n stop tempertures of eh fn stge. The minimum temperture ifferene etween two onseutive strt tempertures is of 0.5 F (0.3 C). *These prmeters must e set seprtely for winter & summer. V1-V2 Bnwiths Set the numer of egrees tht is require for vrile outputs to reh their full spee (se ). This prmeter rnges from 0.5 to 20.0 F (0.3 to 11.1 C). *These prmeters must e set seprtely for winter & summer.. In ition, they re only essile if vrile outputs re enle (se. 4.5) n if the vrile outputs re using the vrile operting moe (se ). CC24-7 ELITE rev.23 27

28 V Output Fn Settings V Output Settings 0-10V Output Settings Show Settings of : Output 2 Output Type Cooling Strt Temperture 80.0 F Stop Temperture 80.0 F Bnwith 3.0 F Minimum 15 % Mximum 100 % Moe 0-10V 2. Set the following prmeters: Refer to setion for further informtion on these prmeters) Show Settings of Selet the proper 0-10V output. One tht will e use for ventiltion or ooling purpose. *Note tht the first 0-10V output is reserve to ontrol lights if lights hve een enle uring the instlltion. Output Type Selet Cooling for the output to operte s n inepenent fn stge. Press Enter to vlite the sttus. The following menus re then isplye: Strt temperture this is the temperture t whih the 0-10V output strts operting ontinuously t minimum spee. The strt temperture n e juste of +/- 40 F (22.2 C) from the set point. Stop Temperture Temperture t whih the 0-10V output is etivte when the room temperture ereses. It n e juste from 0.5 F (0.3 C) elow the strt temperture to -40 F (22.2 C). Bnwith Temperture intervl over whih the output goes from its minimum spee to its mximum spee (refer to the previous grph). The nwith n e juste from 0.5 to 10 F (0.3 to 11.1 C). Min/Mx Spees Minimum n mximum spees of the selete 0-10V output. This prmeter rnges from 0 to 100%. The mximum spee must e greter thn the minimum spee. Moe Selet the proper signl use y the selete output : 0-10V or 10-0V. 28 CC24-7 ELITE rev.23

29 6.3. Tunnel Curtin The ontroller n ontrol up to 2 enwll urtins for tunnel ventiltion. These urtins n either ontrolle y the stti pressure (SP) level or they n move oring to timer. Refer to setion 4.5 to selet the proper operting priniple (Time/SP) Stti Pressure Curtins Priniple of Opertion The ontroller n ontrol 2 pressure-se tunnel urtins. To enle the first tunnel urtin output, nswer Yes to the Use Tunnel question in the instlltion menu n set the tunnel moe to SP. To use the seon inlet output s pressure-se tunnel urtin, enle the 2n inlet output in the instlltion menu n set it s eing tunnel urtin tht works oring to stti pressure (refer to setion 6.5). The tunnel urtins strt opening when the fn stge tht signls the eginning of tunnel ventiltion is rehe. At tht moment, the urtins strt eing ontrolle oring to the pressure level. High / Low Pressure Limits: When the stti pressure level exees the high pressure limit, the urtins open uring the Open Time n then sty in ple uring the Off Time. This proess is repete up until the stti pressure level goes k into the eptle pressure rnge. The reverse proess is performe when the stti pressure ereses elow the low pressure limit; the urtins lose uring the Close Time n then sty in ple uring the Off Time. The Off Time is ommon for oth the losing n opening yles. Animl Age: It is possile to limit the use of the tunnel ventiltion stges oring to the ge of the nimls: you n either speify the minimum ge t whih tunnel ventiltion is llowe, or you n speify the mximum llowle tunnel stge for 3 ifferent ges (refer to setion 4.5 to enle/isle the Multiple Tunnel w/ Age funtion). Stti pressure Groups: Two groups of stti pressure settings n e efine for the tunnel urtin. These groups llow using ifferent high/low pressure limits s the room temperture hnges. The seon group of pressure settings strts eing use t the strt-up of user-efine fn stge. Exmple: When the strt temperture of stge 7 is rehe, the tunnel urtin strts using the seon group of stti pressure settings; in other wors, new high n low pressure limits strt eing use. The initil group of prmeters re use one gin when the room temperture ereses elow the stop temperture of stge 7. Stti pressure limits Hi Set point2 (Open t) Hi Set point1 (Open t) Lo Set point2 (Close t) Lo Set point1 (Close t) Exmple: Trnsition etween stti pressure groups (oring to fn stges) Fn Stge 7 Stop T Fn Stge 7 Strt T Room T Stti Pressure Opening of the Curtin s Funtion of Stti Pressure Siewll Hi pressure limits* The urtin open The urtin strts losing fter the Win Dely hs elpse. The urtin stop losing The urtin strt opening fter the Win Dely hs elpse. The urtin stop opening Siewll Lo pressure limits* The urtin o not move Win Dely The urtin lose Win Dely *The Hi n Lo pressure limits n utomtilly e juste oring to the outsie temperture Time CC24-7 ELITE rev.23 29

30 Settings 11. Tunnel Curtin or press E * or 12. Tunnel Curtin 2** * This menu is essile if the first tunnel urtin is enle (s.4.5). ** This menu is essile if the 2n inlet output is use s tunnel urtin (se. 4.5). Tunnel Curtin Tunnel Strts t Stge 3 Minimum Animl Age 0 ys Animl ge #1 21 ys Mximum Tunnel Stge #1 10 Animl ge #2 28 ys Mximum Tunnel Stge #2 10 Animl ge #3 35 ys Mximum Tunnel Stge #3 10 Close Curtin t Open Curtin t.050 WC.080 WC Stti Pressure Settings 2 Strt t Stge # 10 Close Curtin t.050 WC Open Curtin t.080 WC Open Time Close Time Off Time 60 se 60 se 10 se Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: The prmeters elow will only pper this wy if the selete tunnel urtin opertes oring to the stti pressure level (see setion 4.5). Tunnel Curtin strts t Stge The urtin strts eing use when the strt temperture of this fn stge is rehe. Minimum Age Animl ge elow whih the tunnel urtin remins lose. Tunnel ventiltion n only e enle when this ge is rehe. This prmeter rnges from 1 to 450 ys. Derese the vlue to Off if you wnt to isle this funtion. *Aessile if the Multiple Tunnel Stge w/ Age funtion is isle (se. 4.5). Animl Age #1-3 This is the niml ge elow whih tunnel ventiltion is limite to the speifie mximum tunnel stge. This prmeter rnges from -5 to 450 ys. Negtive y vlues re use to prepre the room efore letting the nimls enter the uiling. Derese the vlue to Off if you wnt to isle this funtion. *Aessile if the Multiple Tunnel Stge w/ Age funtion is enle (se. 4.5). Mximum Tunnel Stge #1-3 This is the mximum tunnel stge tht n e performe when the nimls re younger thn the speifie ge. Note tht mximum tunnel stge #3 is utomtilly set to the highest fn stge. *Aessile if the Multiple Tunnel Stge w/ Age funtion is enle (se. 4.5). Open / Close Curtin t Set the stti pressure limits elow/ove whih the tunnel urtin opens n loses oring to timer. This prmeter rnges from 0 to 0.2 inhes of wter (0 to 50P). Stti Pressure Settings 2 The following proeure shows how to set the tunnel urtin s seon group of pressure settings. *Refer to the previous setion for further informtion on these prmeters. Note tht the following menus re only essile if the seon group of pressure settings is enle (se. 4.5). Strt t stge Selet the fn stge t whih the ontroller swithes from its regulr pressure settings to the seon group of pressure settings. This menu only is only shown if the Stge trnsition metho etween groups of pressure settings is selete (se. 4.5). Open/Close Limits (seon settings) Set the stti pressure level elow whih the urtin loses n ove whih it opens when the seon groups of stti pressure settings is use. This prmeter rnges from 0 to 0.2 inhes of wter (0 to 50P). Open / Close / Off Times Set the urtin s opening n losing times to the esire vlue. This timer is use when the stti pressure level exees the high or low pressure limits n re ommon to oth stti pressure groups. This prmeter rnges from 0 to 30 minutes. 30 CC24-7 ELITE rev.23

31 Timer-Bse Curtin Priniple of Opertion The ontroller n ontrol 2 timer-se tunnel urtins. To enle the first tunnel urtin, nswer Yes to the Use Tunnel question in the instlltion menu n set the tunnel moe to Time. To use the seon inlet output s timer-se tunnel urtin, enle the 2n inlet output in the instlltion menu n set it s eing tunnel urtin tht works oring to time (refer to setion 6.5). The tunnel urtins strt opening when the fn stge tht signls the eginning of tunnel ventiltion is rehe. At tht moment, the urtins open oring to the opening time tht is ssoite with tht stge. When hlf of the opening time hs elpse, the stge s fns re tivte. The tivtion of every onseutive fn stge uses the urtins to open further. Animl Age: It is possile to limit the use of tunnel ventiltion oring to the ge of the nimls: you n either speify the minimum ge t whih tunnel ventiltion n strt eing use, or you n speify the mximum llowle tunnel stge ssoite with three ifferent ges (refer to setion 4.5 to enle/ isle the Multiple Tunnel w/ Age funtion). Opening Times: The urtin s opening times re ssoite with the tivtion of the fn stges. When the strt temperture of stge is rehe, the urtin opens oring to the opening time ssoite with the stge Settings The following settings re only ville if the tunnel urtin opertes in timer moe. Refer to setion 4.5 to enle this operting moe. 11. Tunnel Curtin or press E * or 12. Tunnel Curtin 2** * This menu is essile if the first tunnel urtin is enle (s.4.5). ** This menu is essile if the 2n inlet output is use s tunnel urtin (se. 4.5). 2. Set the following prmeters: The prmeters elow will only pper this wy if the selete tunnel urtin opertes oring to timer (see setion 4.5). Tunnel Curtin strts t Stge The tunnel urtin strts opening when the strt temperture of this fn stge is rehe. Minimum Age Animl ge elow whih the tunnel urtin remins lose. Tunnel ventiltion n only e enle when this ge is rehe. This prmeter rnges from 1 to 450 ys. Derese the vlue to Off if you wnt to isle this funtion. *This prmeter is essile if the Multiple Tunnel Stge w/ Age funtion is isle (se. 4.5). Tunnel Curtin Tunnel Strts t Stge 3 Minimum Animl Age 0 ys Animl ge #1 21 ys Mximum Tunnel Stge #1 10 Animl ge #2 28 ys Mximum Tunnel Stge #2 10 Animl ge #3 35 ys Mximum Tunnel Stge #3 10 Open n Close Time Totl Curtin Run Time Stge 3 Stge 4... Stge 16 2:00 (m:s) 0:30 (m:s) 0:30 (m:s) 0:00 (m:s) Exit: Press Bk Chnge: Press +/- Press to selet n item Animl Age #1-3 This is the niml ge elow whih tunnel ventiltion is limite to the speifie mximum tunnel stge. This prmeter rnges from -5 to 450 ys. Negtive y vlues re use to prepre the room efore letting the nimls enter the uiling. Derese the vlue to Off if you wnt to isle this funtion. *Aessile if the Multiple Tunnel Stge w/ Age funtion is enle (se. 4.5). Mximum Tunnel Stge #1-3 This is the mximum tunnel stge tht n e performe when the nimls re younger thn the speifie ge. Note tht mximum tunnel stge #3 is utomtilly set to the highest fn stge. *Aessile if the Multiple Tunnel Stge w/ Age funtion is enle (se. 4.5). Fn Stge Sttus Stge x+1 ON Stge x ON Opening of Tunnel Curtin s Funtion of Temperture Strtup of stge #x + 1: The urtin opens oring to the opening time ssoite to fn stge #x + 1. Totl Curtin Run Time Set the totl time tht is require for the tunnel urtin to open totlly. The sum of ll opening times elow nnot exee this time limit. This prmeter rnges from 0 to 15 minutes. Curtin Opening Times Selet the opening time tht is ssoite with the tivtion of eh fn stge. This prmeter rnges from 0 to 15 minutes. Off The urtin strts opening n then stge X fns strt running. Set Point Fn stge #X Stop T Fn stge #X Strt T (first tunnel stge) Fn stge #X+1 Stop T Fn stge #X+1 Strt T Room T CC24-7 ELITE rev.23 31

32 6.4. Inlets & Vent Doors 1. First Inlet Output: The first inlet output n either e use to ontrol vent oors (pressure or timer-se) or it n e use to onnet up to 10 externl ir inlet moules suh s the SB3000 (potentiometer feek ontrol) or the SB3500 (timer-se inlet ontrol). To etermine the use of the first inlet output, set the Vent Door Moe prmeter properly in the instlltion menu (see setion 4.5). 2. Seon Inlet Output: The 2 n inlet output n either e use to ontrol n tti vent, siewll vent (vent oor) or supplementry tunnel urtin. To enle the seon inlet output, selet the proper output funtion in the instlltion menu ( Use 2n inlet? question in setion 4.5). The ir inlet tht is onnete to the seon output n either operte oring to the stti pressure level or in timer moe, s funtion of room temperture. Refer to setion 4.5 to hoose the proper funtion n operting moe of the seon inlet output ( Atti Moe or 2n Inlet Moe prmeter). 32 CC24-7 ELITE rev.23

33 Inlet on Externl SB Moules The first inlet output n e use to onnet externl ir inlet ontrollers (SB moules). To progrm the ir inlets tht re onnete to these SB moules, you must refer to the user s mnul enlose with your prtiulr moule (SB3000 or SB3500) When externl SB moules re use to efine the position of the ir inlets, the CC24-7 Elite n still sk these moules to just the inlet opening when the stti pressure or the room temperture gets out of rnge. This setion explins how these opening ompenstion methos work. No ompenstion is pplie on the inlets t the strtup of new fn stge. When fn stge strts, the ontroller resets the urrent ompenstion vlues n reefines them oring to the pressure & temperture onitions mesure t tht time. The SB3500 limits the ompenstion vlue tht n e pplie on the ir inlets to 50% of their regulr opening. If the ontroller sens ompenstion request tht exee this limit the SB Moule just won t onsier it n won t move the inlet ny further. Stti Pressure Compenstion: A ompenstion n e use to ensure ertin uniformity in the stti pressure level in the room. This stti pressure ompenstion llows opening or losing inlets further when the stti pressure level gets out of rnge. When the stti pressure level exees the norml rnge (ove the Hi Pressure Set point or elow the Lo Pressure Set Point), the ontroller wits for the Win Effet Dely to mke sure this unusul pressure onition is not temporry. If the pressure is still out of rnge fter this ely hs elpse, the inlet ompenstion (%) is pplie on the opening of ll inlets: they lose further y their respetive ompenstion vlue (%) when the pressure level is too low [point A on the grph] or open further y their ompenstion vlue (%) when the pressure level is too high [point C on the grph]. The ontroller then wits for the Win Effet Dely one gin. If the pressure level is still out of rnge fterwrs, the opening ompenstion is pplie one more. This yle is repete up until the pressure gets k in the norml rnge or until new stge strts. When the pressure level gets k to the norml rnge [points B & D on the grph], ll inlets keep their ompenste position until the eginning of new stge. No ompenstion is pplie on the inlet opening when new stge strts. Temperture Compenstion: A ompenstion n e tivte to ensure ertin uniformity in the room temperture: the ir inlet positions re utomtilly juste when the temperture reing of the inlets proes iffers from the verge room temperture re y the ontroller. The inlet temperture ompenstion is expresse s perentge per egree ifferene etween the verge ontroller temperture n the verge reing of the proes ssigne to the inlet. It etermines y how muh the inlet must open or lose to help reue the temperture ifferenes in the uiling. For eh egree ove or elow the verge temperture, the inlet will open or lose using the ompenstion vlue ssigne y the user. For exmple, if the ompenstion vlue is set to 2%/ F n the inlet s proes re 3 F ove the verge ontroller temperture, the inlet will open 6% further to help erese the temperture in tht zone. Refer to setion to ssign the inlets temperture proes. If temperture ompenstion hs to e pplie on the position of the ir inlets, the ontroller only sens ompenstion request of 1% t time. Refer to the instlltion menu to speify the frequeny t whih the 1% ompenstion must e pplie ( Sen Compenstion Eh prmeter in setion 4.5). Inrese inlet opening Stti Pressure Stti Pressure Compenstion on the Inlet Opening Hi Set Point* Keep inlet position Lo Set Point* Derese inlet opening Win Dely Win Dely Win Dely Win Dely Win Dely Win Dely Time Inlet loses further (y omp vlue%) Inlet loses further (y omp vlue%) Inlet loses further (y omp vlue%) Inlet opens further (y omp vlue%) Inlet opens further (y omp vlue%) Inlet opens further (y omp vlue%) CC24-7 ELITE rev.23 33

34 Settings 10. Inlet Compenstion * * This menu is essile if n inlet is enle in the Instlltion menu: Vent Door Moe is set to Ext n numer of inlets is greter thn 1 (setion 4.5). Inlet Compenstion Show Settings of : Inlet 1 T Opening Comp. 5 %/ F SP Comp. 5 % Stti Pressure Low.050 WC Stti Pressure High.080 WC Win Dely 30 se High Set Point The stti pressure ompenstion strts when the pressure level inreses eyon this level. This prmeter rnges from 0 to 0.40 WC. Note tht the high pressure limit must e greter thn the low limit. *This prmeter is ommon to ll inlets n is ville if the stti pressure ompenstion funtion is enle in setion 4.5. Win Dely Eh time this ely hs elpse n the pressure exees the norml rnge, the stti pressure ompenstion is pplie on the opening of ll ir inlets. This prmeter rnges from 30 to 900 seons. *This prmeter is ommon to ll inlets n is ville if the stti pressure ompenstion funtion is enle in setion Set the following prmeters: Refer to the previous setion to get further informtion on these prmeters. Show Settings of Selet the proper inlet then set the ompenstion openings of eh inlet seprtely: T Opening Compenstion Selet the opening perentge tht must e e or remove when the temperture ompenstion is pplie on the inlet openings. This prmeter rnges from 0 to 100%/ F. SP Compenstion Selet the opening perentge tht must e e or remove when the stti pressure ompenstion is pplie on the inlet openings. This prmeter rnges from 0 to 10% *This prmeter is ville if the stti pressure ompenstion funtion on ir inlets is enle in setion 4.5. Low Set Point The stti pressure ompenstion strts when the pressure level ereses elow this level. This prmeter rnges from 0 to 0.40 WC. *This prmeter is ommon to ll inlets n is ville if the stti pressure ompenstion funtion is enle in setion CC24-7 ELITE rev.23

35 Pressure-se Vent Doors Priniple of Opertion When vent oor opertes oring to the level of stti pressure, it loses in timer moe when the pressure level gets lower thn the Low pressure set point or opens in timer moe when the pressure level exees the Hi pressure set point. Groups of stti pressure settings: Two groups of high/low stti pressure settings n e efine. The seon group of settings either strts eing use t the strt-up of hosen fn stge or when the outsie temperture rehes user-efine vlue. The following grphs sum oth ses. 1. Trnsition etween stti pressure settings se on the ventiltion stges: Stti pressure limits Hi Set point2 (Open t) Hi Set point1 (Open t) Exmple: Trnsition etween stti pressure groups (oring to fn stges) The ontroller n ontrol 2 pressure-se vent oor outputs. To enle the first vent oor output, set the Vent Door Moe to SP in the instlltion menu. To use the seon inlet output s pressure-se vent oor, enle the 2n inlet output in the instlltion menu n set it s eing siewll vent tht works oring to stti pressure (refer to setion 6.5). Pre-opening Dely: If the vriles fns re not use uring minimum ventiltion, the vent oors open uring pre-opening time efore the fns strt running. The sme ely is use to lose the vent oors when the fns stop. Refer to setion 4.5 to set the vent oors pre-opening ely. If n tti vent is use, the vent oors will not open until the trnsitionl fn stge is rehe (see setion 6.4.3). Exmple: When the strt temperture of stge 5 is rehe, the vent oors strt operting oring to the seon group of stti pressure settings; therefore, new high n low pressure limits re use. The initil settings eome use one gin when the room tempe rture ereses elow the stop temperture of stge Trnsition etween stti pressure settings se on the outsie temperture: Exmple: When the outsie temperture flls n rehes the outsie temperture influene prmeter vlue + 5 F (2.8 C), grul trnsition etween the two groups of stti pressure settings strts eing one. The seon group of settings is fully use when the outsie temperture rehes the outsie influene temperture vlue. Lo Set point2 (Close t) Lo Set point1 (Close t) Stti Pressure Set Points Hi Set point2 (Open t) Hi Set point1 (Open t) Fn Stge 5 Stop T Fn Stge 5 Strt T Room T Exmple: Trnsition etween stti pressure groups (oring to the outsie temp.) Lo Set point2 (Close t) Stti Pressure Opening of the Vent Door s Funtion of Stti Pressure Lo Set point1 (Close t) 50 F 5.0 F (outsie T influene) 55 F Outsie T Siewll Hi pressure limits* The v.oor open The v.oor strts losing if the low pressure onition is mintine for 5 seons The v.oor stop losing The v.oor strts opening if the low pressure onition is mintine for 5 seons The v.oor stop opening The v.oor o not move 5 seons Siewll Lo pressure limits* The v.oor lose 5 seons *The Hi n Lo pressure limits n utomtilly e juste oring to the outsie temperture Time CC24-7 ELITE rev.23 35

36 Settings 10. Vent Doors / Stti Pressure* or 12. Vent Doors 2 / Stti Pressure** * This menu is essile pressure-se vent oors re enle (se. 4.5). ** This menu is essile if the 2n inlet output is use s siewll vent (se. 4.5). Vent Doors / Stti Pressure Close Vent Doors t Open Vent Doors t.050 WC.080 WC Stti Pressure Settings 2 Strt t Stge # 10 Outsie T Influene 50.0 F Close Vent Door t.050 WC Open Vent Door t.080 WC Open Time Close Time Off Time Close Vent Doors t Stge 60 se 60 se 60 se Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: None Outsie T Influene Set the outsie temperture elow whih the ontroller fully swithes to the seon group of pressure settings. *This prmeter is essile if the seon group of pressure settings uses the Out T trnsition moe (se. 4.5).. Open/Close Limits (seon settings) Set the stti pressure level elow whih the vent oors lose n the temperture ove whih they open when the seon groups of stti pressure settings is use. The open n lose limits n e juste from 0 to 0.2 inhes of wter olumn (0 to 50P).*This prmeter is essile if the seon group of pressure settings is enle (s.4.5). Open Time When the stti pressure exees the Hi pressure set point, the vent oors open uring this ely. This prmeter rnges from 0 to 900 seons. Close Time When the stti pressure level ereses elow the Lo pressure set point, the vent oors lose uring this ely. This prmeter rnges from 0 to 900 seons. Off Time After they hve move, the vent oors hve then sty still uring the Off Time. This ely rnges from 0 to 900 seons. Open/Close Limits Set the pressure level elow whih the vent oors lose n ove whih they open. These prmeters rnge from 0 to 0.2 inhes of wter olumn (0 to 50P). Stti Pressure Settings 2 The following proeure shows how to set the seon group of pressure settings. *This prmeter is essile if the seon group of pressure settings is enle (s.4.5). Close Vent Doors t Stge Selet the fn stge t whih the vent oors must lose. This option n e use to lose the vents t the strtup of tunnel ventiltion for instne. Selet None to etivte this funtion. Strt t stge Selet the fn stge t whih the ontroller swithes from its regulr stti pressure settings to the seon group of stti pressure settings. *This prmeter is essile if the seon group of pressure settings uses the Stge trnsition moe (se. 4.5). 36 CC24-7 ELITE rev.23

37 Timer-Bse Vent Doors This setion only pplies to vent oor output tht uses the uilt-in timer of the CC24-7 Elite ontrol; if the vent oor uses the timer of n externl SB 3500 moule, refer to setion Priniple of Opertion The ontroller n ontrol 2 timer-se vent oor outputs. To enle the firrst vent oor output, set the Vent Door Moe to Time in the instlltion menu. To use the seon inlet output s timer-se vent oor, enle the 2n inlet output in the instlltion menu n set it s eing siewll vent tht works oring to timer (refer to setion 6.5). When vent oor output works in timer moe, you must speify the totl mount of time require to fully open the vent. You must then ssoite n opening with the strtup of eh fn stge (the opening is efine s perentge of the totl opening time). As the room temperture inreses n new stges re tivte, the vent oors will open or lose oringly. An opening step is lso e when vrile fn stge strts (this pplies to stges 1 n 2 only). This step is lle Stge x Min. In the exmple ove, Stge x Min represents the point where stge 1 fns strt running t their minimum intensity. The regulr opening of the vent oor in stge 1 is rehe when the fns reh their full intensity. Vent Doors in Minimum Ventiltion: During the Off Time portion of minimum ventiltion yle, the vent oors lose to their Stge 0 position; uring the On Time, they open to position ssoite with stge 1 (or Stge 1 Min if vrile fns re use). If n tti vent is use, the vent oors will not open until the trnsitionl fn stge is rehe (see setion 6.4.3). Automti Reset of the Vent Doors Position: Resetting the tutor s position lers ll umulte time offsets use y the frequent openings n losings of vent oors. The ontroller resets the tutor s position t regulr intervl to mke sure the vent oors position is lwys urte. This reset is performe utomtilly oring to one of these two methos: Reset the minimum position only (Close moe): Eh time reset is performe, the vent oors totlly lose. One the tutor s position is reset, they return to their previous position Reset towr the nerest position (Open/Close moe): Eh time reset is performe, vent oors fully open if their urrent opening lrey ws higher thn 25%; otherwise, the ontroller loses vent oors to reset the tutor s position. This wy, they o not lose when the room temperture lrey sks for lrge opening. Mke sure limit swithes re lote t oth ens of the tutors when using this resetting metho Settings This proeure shows how to progrm the vent oors tht re using the uilt-in timer of the ontroller n oes not pplies to vent oors tht re using the timer of n externl SB 3500 moule. Refer to setion 4.5 to hoose the operting moe of the vents. 10. Vent Doors / Stti Pressure* or 12. Vent Doors 2 / Stti Pressure** * This menu is essile if timer-se vent oors re enle (se. 4.5). ** This menu is essile if the 2n inlet output is use s siewll vent (se. 4.5). Vent Doors / Stti Pressure Open n Close Times Stge 0 10 % Stge 1 Min 10 % Stge 1 10 % Stge 2 Min 10 % Stge 2 10 % Stge 3 10 %... Stge % Vent Door Run Time 2:00 m:s Auto Reset Moe OPEN/CLOSE Auto Reset Time 6:00A Auto Reset. Every 3 ys Open / Close Time 120 se Strt Mnul Reset Now? No Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: % of totl opening time Stge 3 Opening of Timer-Bse Vent Doors Stge 0 This is the position of the vent oor when the fns re not running in minimum ventiltion ( Off Time portion of the minimum ventiltion timer). Stge x Min Assign vent oor position to the strt-up of eh vrile-spee fn stge (for stges 1 & 2 only). Stge 2 Stge 1 Stge x Assign vent oor position to eh fn stge. Stge 1 min Stge 0 Stge 1 strt T Bnwith Stge 2 strt T Stge 3 strt T Room T Vent Door Run Time Speify the ext time tht is require to reh the tutor s mximum limit swith. The ontroller will limit opening of the vent oors vent oring to this time vlue. CC24-7 ELITE rev.23 37

38 Auto Reset Moe Selet the esire reset moe for the vent oor tutor: hoose Open/Close to reset the tutor towr its nerest position; selet Close to reset it towrs its lose position only; selet Off to isle the uto-reset funtion. *Refer to the previous setion for further informtion out resets. Auto Reset Time Selet the time t whih the tutor reset is performe. Auto Reset Every Selet the frequeny t whih the tutor is reset. This prmeter rnges from 1 reset every 1 to 7 ys. Open / Close Time (Avne) During reset, the ontroller opens or loses the vent oors uring this ely, or up until limit swith is rehe. By efult, this vlue is equl to the totl run time of the tutor. *Aessile from the ftory moe only. Strt Mnul Reset Now? Selet Yes to reset the vent oor position now Atti Vent In orer to extrt the wrm ir from the eiling, the tti vent n open prior to the opening of siewll vents. The seon inlet output of the CC24-7 Elite n e use to ontrol n tti vent (pressure or timer-se vent). To enle this vent, set the sttus of the seon inlet output to Atti in the instlltion menu n then selet its operting moe: Time or SP (see setion 4.5) Pressure-se Atti Vent Opening of the Atti Vent: When it is se on the stti pressure level, the tti vent moves oring to the pressure vritions in the uiling. This is the ext sme priniple s for the pressure-se vent oor outputs. Refer to setion to see how pressure-se tutor moves. Ativtion Perio & Trnsition: When pressure-se tti vent is use, the ir intke insie the uiling is exlusively provie y the tti vent until the room temperture rehes the strtup point of the fn stges tht sks for trnsition ( Atti trnsition stge ). When this trnsition egins, the tti vent stops moving n the vent oors open uring the Trnsition Pre-Open Time. After this ely, the tti vent either stops moving or opens ompletely (epening on the hosen option) n the vent oors strt working normlly. The tti vent will lose when the room temperture rises n rehes userefine fn stge ( Close t stge). Pre-opening Dely: If the vriles fns re not use uring minimum ventiltion, the tti vent opens uring pre-opening time efore the fns strt running. The sme ely is use to lose the tti vent when the fns stop. Refer to setion 4.5 to set the tti vent pre-opening ely. 12. Atti Settings* * Aville if the 2n inlet output is use to ontrol n tti vent (se. 4.5). 2. Set the following prmeters: Refer to setion to get further informtion on these prmeters. The prmeters elow will only pper this wy if the tti vent opertes oring to the stti pressure level (see setion 4.5). Atti Inlet Close Atti t stge 3 Atti trnsition stge 2 Atti stte in trnsition As is/open Trnsition Pre-Open.10 se Close Atti t Open Atti t Open Time Close Time Off Time.050 WC.080 WC 60 se 60 se 60 se Exit: Press Bk Chnge: Press +/- Press to selet n item Close Atti t Stge Set the fn stge t whih the tti vent must lose. The ir intke in the uiling is exlusively provie y the vent oors t the strtup of this stge. The losing stge must e higher thn the trnsition stge tht is efine elow. Atti Vent Trnsition Stge The ir intke in the uiling is exlusively provie y the tti vent up until the room temperture rehes the strt temperture of the hosen fn stge. Selet the fn stge t whih the ir intke must strt eing provie y the vent oors (fn stge 1 to 6). Atti Stte in Trnsition Speify wht the tti vent must o uring trnsition stge: it n either sty in ple ( As is ) or it n open ompletely ( Open ). Trnsition Pre-Open Selet uring how muh time the vent oors must open prior to moving the tti vent when the trnsitionl fn stge is rehe. At the en of this ely, the ir intke is provie y oth the tti vent n the vent oors. Open/Close Limits Set the pressure level elow whih the tti vent loses n ove whih it opens. These prmeters rnge from 0 to 0.2 inhes of wter olumn (0 to 50P). Open Time When the stti pressure exees the Hi pressure set point, the tti vent opens uring this ely. This prmeter rnges from 0 to 900 seons. Close Time When the stti pressure level ereses elow the Lo pressure set point, the tti vent lose uring this ely. This prmeter rnges from 0 to 900 seons. Off Time After is hs move, the tti vent then stys still uring the Off time. This ely rnges from 0 to 900 seons. 38 CC24-7 ELITE rev.23

39 Timer-se Atti Vent Opening of the Atti Vent: When n tti vent works in timer moe, you must speify the totl time tht is require to fully open the vent. You must then ssoite n opening time to the strtup of eh fn stge tht preees the trnsition stge. As the room temperture inreses n new stges re tivte, the tti vent will open or lose oringly. Ativtion Perio & Trnsition: When timerse tti vent is use, the ir intke insie the uiling is exlusively provie y the tti vent until the room temperture rehes the strtup point of the fn stges tht sks for trnsition ( Atti trnsition stge ). When the trnsition egins, the vent oors strt operting normlly n the tti vent either stops moving or opens ompletely (epening on the hosen option). The tti vent finlly loses when the room temperture rehes the fns stge tht sks for it to lose ( Close tti t stge ). The ir intke eomes exlusively provie y the vent oors t tht moment. Atti Vent in Minimum Ventiltion: A preopening ely must e efine to open the tti vent when the fns re running in minimum ventiltion ( On Time portion of the minimum ventiltion timer). Note tht the pre-opening is me prior to the tivtion of the fns t the eginning of eh yle. 12. Atti Settings* * Aville if the 2n inlet output is use to ontrol n tti vent (se. 4.5). 2. Set the following prmeters: The prmeters elow will only pper this wy if the tti vent opertes oring to timer (see setion 4.5). Close Atti t Stge Set the fn stge t whih the tti vent must lose. The ir intke in the uiling is exlusively provie y the vent oors t the strtup of this stge. The losing must e higher thn the trnsition stge efine elow. Atti Trnsition Stge Selet the fn stge t whih trnsition is me from the tti to the siewll ir intke. When this stge is rehe, the tti vent either stops moving or opens for its totl run time (epening on the trnsition stte elow) n the vent oors strt operting normlly. Atti Stte in Trnsition Speify wht the tti vent must o uring trnsition stge: it n either sty in ple ( As is ) or it n open for its totl run time ( Open ). Totl Atti Run Time Speify the ext time tht is require to reh the tutor s mximum limit swith. The ontroller will limit opening of the tti vent oring to this time vlue. Stge x Opening Time Assign n opening time of the tti vent to ll fn stges tht preee the trnsition stge. *The sum of ll stge openings must e shorter thn the Totl Atti Run time if the trnsition moe is set to Open ove. Atti Inlet Close Atti t stge 3 Atti trnsition stge 2 Atti stte in trnsition As is/open Open n Close Time Totl Atti Run Time Stge 1 Pre-Open Atti ely 2:00 (m:s) 0:30 (m:s) 10 se Exit: Press Bk Chnge: Press +/- Press to selet n item Pre-Open Atti Dely Assign the opening time of the tti vent for the minimum ventiltion moe: the tti vent will open uring this mount of time just efore the fns strt running n will sty in ple until the fns stop uring minimum ventiltion yle.. CC24-7 ELITE rev.23 39

40 6.5. Cooling Outputs The ontroller hs 4 ooling outputs tht n e use to operte ooling evies suh s mist units. The intensity of these outputs inreses grully s the house temperture inreses. The following igrm illustrtes the ooling outputs opertion. Cooling Output Timer Mx Timer Regulr Timer OFF OFF T Cooling Output ON T Mx Run T The ooling output strts operting oring to timer (On Time & Off Time) when its strt temperture is rehe. The output s timer grully hnges s the temperture inreses. It rehes the mx timer settings (Mx On Time & Mx Off Time) when the house temperture rehes the Mximum Run Temperture. Strt n stop tempertures of ooling outputs re relte to the house set point. This mens tht when the house set point hnges, strt n stop tempertures re juste onsequently. T You n speify n operting time rnge in orer to stop ooling outputs uring night. Sine they re relte to the set point, the On n Off tempertures of the ooling outputs re likely to hnge with time. For this reson, temperture limit n e efine to voi tivting the ooling outputs when the room temperture is not high enough to ensure wter evportion (see following grph). Cooling Output Timer Mx Timer Regulr Timer OFF 14. Fn/Cool./Nt. Temp. Settings 2. Cooling Temperture Settings* * Aville if ooling outputs re enle (se. 4.5). Cooling 1 Temperture Limit for the Cooling Output NO COOLING Hyst. No Cooling T COOLING Cooling Temperture Settings Strt Temperture 95.0 F Stop Temperture 94.0 F Mximum Temperture F On Time 1 1:00 (m:s) Off Time 1 3:00 (m:s) On Time 2 2:00 (m:s) Off Time 2 12:00 (m:s) Strt t 6:00 A Stop t 9:00 P Cooling 2 Strt Temperture 95.0 F Stop Temperture 94.0 F... No ooling uner 72.0 F Hysteresis 0.5 F Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Strt Temperture Set the temperture t whih the ooling output strts operting using the first timer. This prmeter rnges from the set point to 120 F (48.9 C). T Mximum Temperture Set the temperture t whih the ooling output swithes to the seon timer. This prmeter rnges from 0.5 F (0.3 C) ove the strt temperture to 120 F (48.9 C). On Time 1 & 2 Set oth timers On n Off times to the esire vlues. This prmeter rnges from 0 to 30 minutes. Strt / Stop t Cooling outputs n only e tivte over this perio of time. This llows etivting these outputs uring night for instne. No ooling uner The ooling output is utomtilly isle when the verge temperture of its proes flls elow the No ooling uner temperture. Set this prmeter to the esire vlue (from F to 85.0 F). Hysteresis (Avne) An hysteresis is use to restrt the ooling output when the temperture rises ove the No Cooling T. By efult, the hysteresis is set to 0.5 F. *This prmeter is only essile with the ftory psswor. Stop Temperture Set the temperture elow whih the ooling output stops. This prmeter rnges from 0.5 F (0.3 C) elow the strt temperture to -40 F (-40 C). 40 CC24-7 ELITE rev.23

41 6.6. Nturl Ventiltion Priniple of Opertion The urtins operte oring to the verge temperture in their respetive zones. Their opening n losing tempertures re relte to the room set point, whih mens they re juste onsequently when hnge in the set point ours. Refer to setion to ssign the temperture proes lote in eh nturl zone. Nturl ventiltion egins when the room temperture rehes the strt temperture of user-efine fn stge (Strt Nturl t Stge). At tht moment, the ontroller opens ll nturl ventiltion urtins uring their respetive Initil Opening Time. One the ontroller is in nturl ventiltion, the urtins strt operting in timer moe: they open oring to n opening yle (Open Time & Off Time) when the verge temperture in their respetive zone is ove the Open At temperture; they lose oring to the losing yle (Close Time & Off Time) when the temperture in their zone is lower thn the Close At temperture. Nturl ventiltion is isle t the strtup of the first tunnel stge or when the room temperture ereses to the nturl ventiltion s stop temperture. When it stops, the ontroller fully loses ll nturl ventiltion urtins Trnsition Between Nturl & Tunnel Ventil. 1. NATURAL VENTILATION > TUNNEL VENTILATION: When the room temperture inreses n rehes the Open t temperture of the nturl ventiltion urtin [point A on the piture], the urtin opens in timer moe [point B on the piture]. If the tunnel urtin is lso use in nturl ventiltion, it will lso open following this timer. When the room temperture rehes the strt temperture of the first tunnel stge [point C on the piture], the nturl ventiltion urtin stys still uring the Nturl Close Dely (5 minutes y efult) then fully loses. Here is wht hppens to the tunnel urtin when the first tunnel stge is rehe: Nturl ventiltion Tunnel ventiltion 1st tunnel stge (Open t) (Close t) GRAPH 1 From nturl to tunnel ventiltion Temperture rises If the tunnel urtin is se on timer: If the tunnel urtin ws not use in nturl ventiltion: The tunnel urtin opens to the position ssoite with the first tunnel stge. When it rehes hlf the opening of tht stge, the fns strt running. Curtin Sttus Reltion etween Fn Stges & Nturl Ventiltion Curtins If the tunnel urtin ws use in nturl ventiltion: The tunnel urtin opens uring its Totl Run Time prmeter vlue (se ) then repositions itself to the opening ssoite with the first tunnel stge. This llows resetting the urtin s position efore moving on to the tunnel ventiltion moe. ON The urtin loses in timer moe The urtin opens in timer moe If the tunnel urtin is se on the stti pressure: OFF Nturl Ventiltion Sttus Set Point 0.5 F Close t Open t Averge T of the urtin s proes If the tunnel urtin ws not use in nturl ventiltion: The tunnel urtin opens uring its Pre Open Time prmeter vlue. When this ely hs elpse, the ontroller strts the fns n the opening of the urtin eomes se on the stti pressure settings. ON OFF If the tunnel urtin ws use in nturl ventiltion: The opening of the urtin eomes se on the stti pressure settings t the strt-up of the first tunnel stge. Set Point Stop Nturl Strt Nturl First tunnel stge Stge Ativtion CC24-7 ELITE rev.23 41

42 2. TUNNEL VENTILATION > NATURAL VENTILATION: If the tunnel urtin is not use in nturl ventiltion: When the room temperture flls n gets lower thn the stop temperture of the first tunnel stge [point A], the ontroller reenters in nturl ventiltion: it opens the nturl urtin uring the Nturl Open Dely (5 minutes y efult) n loses the tunnel urtin. When the ely hs elpse, the nturl urtin strts operting oring to the nturl ventiltion timer [point B]. If the tunnel urtin is use in nturl ventiltion: When the room temperture flls n gets lower thn the stop temperture of the first tunnel stge [point A], the ontroller reenters in nturl ventiltion n opens the tunnel n nturl ventiltion urtins uring the Nturl Open Dely (5 minutes y efult). When this ely hs elpse, oth urtins operte oring to the nturl ventiltion timer [point B]. Nturl ventiltion Tunnel ventiltion 1st tunnel stge (Open t) (Close t) Temperture flls Settings 14. Fn/Cool./Nt. Temp. Settings 3. Nturl Temperture Settings * This menu is essile if nturl zones re enle (se. 4.5). Nturl Zone Settings Nturl Zone 1 Open Curtin 84.5 F Close Curtin 85.5 F Open Time 0:30 (m:s) Close Time 0:30 (m:s) Off Time 1:00 (m:s) Win Dely 0:15 (m:s) Initil Open Time 0:20 (m:s)... Strt Nturl t Stge 4 Stop Nturl t Stge 3 Tunnel Strts t Stge 6 Tunnel 2 Strts t Stge 6 Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Refer to the previous setion to get further informtion on these prmeters. Mke sure to selet the right zone efore justing these prmeters. Press the own-rrow key to sroll the isply n selet the esire nturl ventiltion zone. Open Curtin Set the temperture ove whih the urtin opens oring to timer when the ontroller is in nturl ventiltion. This prmeter rnges from the set point to 120 F (48.9 C). *This prmeter must e set seprtely for eh seson. elpse. This wy, the ontroller oes not open or lose urtins when win rfts use temporry temperture vritions. Set the win ely to the esire vlue. This prmeter rnges from 0 to 15 minutes. Initil Open Time Curtins of ll nturl zones open uring their respetive Initil Open Time when the ontroller enters in nturl ventiltion. This prmeter rnges from 0 to 15 minutes. Strt Nturl t Stge Selet the fn stge t whih the ontroller enters in nturl ventiltion. Stop Nturl t Stge Selet the fn stge t whih the ontroller exits from nturl ventiltion. Tunnel/ Tunnel 2 Strts t Stge This is the fn stge t whih eh tunnel urtin strts opening. This menu is shown for onsulttion purpose only n nnot e hnge. *Refer to the tunnel ventiltion hpter to moify the first tunnel stge. Nturl Close Dely (Avne) This ely is lunhe t the eginning of the first tunnel stge. One it hs elpse, the ontroller loses ll urtins in nturl zones. *Ftory setting. Nturl Open Dely (Avne) All nturl ventiltion urtins open uring this ely when the ontroller swithes from the tunnel moe to nturl ventiltion. *Ftory setting. GRAPH 2 From tunnel to nturl ventiltion Close Curtin Set the temperture elow whih the urtin loses oring to timer when the ontroller is in nturl ventiltion. *This prmeter must e set seprtely for eh seson. Open / Close / Off Times Set the timer tht is use to open n to lose the urtins in eh nturl zone (the Off time is ommon to oth the opening n losing yles). This prmeter rnges from 0 to 15 minutes. Win Dely When the ontroller is in nturl ventiltion n the temperture in nturl zone ereses elow the Close At temperture or inreses ove the Open At temperture, the urtin in tht zone only strts moving fter the win ely hs 42 CC24-7 ELITE rev.23

43 7. HEATERS 7.1. Heting Stges The ontroller n operte up to 16 inepenent heting outputs. These outputs operte oring to their strt n stop temperture s illustrte elow. Refer to setion 4.5 to tivte the heting outputs. Heters 1-8: These re the si heting outputs of the ontroller. Heters Hi Fire: The hi fire option llows ing supplementry step to eh tivte heting output. Eh heting output n hi fire step opertes oring to its own settings: proe ssignment, rely seletion n strt/stop tempertures. In other wors the hi fire option llows ouling the numer of heting outputs. Refer to setion 4.5 to tivte the heters hi fire option. Operting Temp. of the Heting Outputs: Strt Temperture: The strt temperture of eh heting output is relte to the set point. This mens tht if the set point hnges, the strt temperture is juste onsequently. Stop Temperture: If the heting urve n the Hi/Lo Fire options re oth isle, the stop temperture of eh heting output is relte to the set point (this mens tht if the set point hnges, the stop temperture is juste onsequently). If the heting urve or the Hi/Lo Fire option is enle, the stop temperture for given heting output eomes se on the strt temperture of the output (this mens tht if the strt temperture of the output hnges, the stop temperture is juste onsequently). 13. Heter Strt / Stop Temperture Heter Strt / Stop Temperture Current Temp. Set Point 80.0 F Heter 1 Curve Off Strt Temperture 78.0 F Stop Temperture 79.0 F or Stop Aove Strt Tmp 1 F Heter 1 Hi Curve Off Strt Temperture 78.0 F Stop Temperture 79.0 F or Stop Aove Strt Tmp 1 F Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters. The strt n stop tempertures of heting output nnot e moifie if the heter uses urve. Refer to the following setion to enle/isle heters urves. Heters Strt / Stop Tempertures Set the strt n stop temperture of eh heting output. The stop temperture must e t lest 0.5 F (0.3 C) greter thn the strt temperture for given heter. Not. Due to some tehnil limittions, the Stop Temperture of the heting outputs n either e expresse s n solute vlue (e.g F) or s reltive vlue (e.g. Stop 1 F ove the Strt Temperture). Hi Fires Strt / Stop Tempertures Set the strt n stop tempertures of eh hi fire heting output. The stop temperture must e t lest 0.5 F (0.3 C) greter thn the strt temperture for given heter. *This prmeter is ville if the hi fire option is enle (s.4.5). Not. Due to some tehnil limittions, the Stop Temperture of the heting outputs n either e expresse s n solute vlue (e.g F) or s reltive vlue (e.g. Stop 1 F ove the Strt Temperture). Heting Output Heter Stges Heter 1 Hi Fire ON Heter 1 Hi Fire OFF Heter 1 ON Heter 1 OFF Heter 1 Hi Fire Strt T Numer of egrees ove Strt T Heter 1 Hi Fire Stop T Heter 1 Strt T Numer of egrees ove Strt T Heter 1 Stop T Room T CC24-7 ELITE rev.23 43

44 7.2. Heter Curve Priniple of Opertion This urve llows n utomti justment of the heters strt temperture over time. The heters strt temperture hnges using 10 steps. Eh step speifies y numer n strt temperture for tht y. The y numer is se on the niml ge. One the 10 steps re efine, the urve must e tivte. The ontroller then strts hnging the heters strt temperture every hour in liner fshion etween onseutive steps of the urve. When the lst step is rehe, the strt temperture of the heters for tht y is mintine until new th strts n until the niml ge is reset. Heter x Strt Temp Heter Curve Dy NOTE: Certin restritions pply to reue the risk of errors: - The highest possile y numer is Deresing y numers is not llowe. - Inresing the strt temperture over time is not llowe. - All ten steps must e speifie. If you on t nee ten ifferent steps, repet the lst temperture for eh unneessry step. Use the opy/pste funtion to progrm severl heting output tht use the sme urve. Refer to setion Settings 1. Selet 9. Curve Settings x. Heter x Strt Temperture* * Aville if the heters Offset urve is enle (se. 4.5). Heter 1 Strt Temperture Curve Strt Temp F y F y F y F y F y F y F y F y F y F y F Curve Sttus Off Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: The urve steps n only e moifie while the urve is off. Dy Numer Set the y for eh of the 10 steps. This numer orrespons to the niml ge n is justle from -5 to 450 ys. Negtive vlues re use to prepre the house efore the letting the nimls enter the uiling. Strt Temperture Set the heter s strt temperture for eh step. Curve Sttus Selet Yes to tivte the urve. One it is enle, the heter s strt temperture eomes utomtilly juste etween onseutive points of the urve; for this reson the urve steps nnot e moifie while the urve is on Copy/Pste Het Curves 1. Selet 9. Curve Settings 20. Copy Pste Heter Curve* * Aville if the heters Offset urve is enle (se. 4.5). Copy Pste Heter Curve Copy from: Heter 1 Pste to: Heter 2 Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Selet the heting urve tht nees to e uplite n the trget urve s follows: Copy From This is the soure urve. The one tht will e uplite. Pste to This is the trget urve. The one on whih the opie urve will e pste. 3. One the soure n the trget urves re efine, the messge Confirm? ppers on the isply. Selet Yes to onfirm the uplition. The messge Copy in progress... plese wit.. is then isplye. Wit until the opying proess is over. 44 CC24-7 ELITE rev.23

45 7.3. Het Mts (0-10V Heting Outputs) The ontroller hs four 0-10V outputs to ontrol supplementry vrile fn stges, lights, or heting evies. The following proeure shows how to use 0-10V outputs to ontrol heting units. This type of output is tivte t its minimum intensity when its Strt Temperture is rehe. It inreses in intensity s the room temperture ereses n rehes its mximum intensity when the temperture ereses elow the Mx. Het. temperture. It stops operting when the room temperture inreses ove the output s Stop Temperture V Output Settings 0-10V Output Settings Show Settings of Output 4 Output Type Heter Strt Temperture 80.0 F Stop Temperture 80.5 F Bnwith 3.0 F Minimum 15 % Mximum 100 % Moe 0-10V Exit: Press Bk Chnge: Press +/- Press to selet n item Intensity (%) Mx Min 0-10V Heting Output 2. Set the following prmeters: Show Settings of Selet the proper 0-10V output. Note tht the first 0-10V output is utomtilly reserve to tivte itionl lights if light progrms re enle. Output Type Choose Heter to use the 0-10V output to operte n heting evie. Off Mx T Strt T Stop T T of het lmp proes Strt temperture Set the temperture t whih the 0-10V output strts operting ontinuously t its minimum spee. It n e juste of +/- 40 F (22.2 C) from the set point. Stop Temperture Selet the temperture t whih the output stops. It n e juste from 0.5 F (0.3 C) ove the strt temperture to 40 F (22.2 C). Moe Selet the type of signl use y the output (0-10V or 10-0V). CC24-7 ELITE rev.23 45

46 8. LIGHTS Light Progrm 8.1. Priniple of Opertion LIGHT PROGRAMS : The ontroller hs 8 ily light progrms to ontrol the light intensity on ily sis. Eh progrm is ompose of up to 30 steps to vry the light intensity in the y n their tivtion is relte to the niml ge. The following grph illustrtes 4-step light progrm. Light Intensity (%) 80% 30% 0% Step 1 trnsition Step 1 ON time Step 2 trnsition Step 2 ON time Step 3 trnsition Step 3 ON time Step 4 trnsition Step 4 ON time Time 8.2. Ativting Aitionl 0-10V Light Outputs The ontroller hs four 0-10V outputs to ontrol supplementry vrile fn stges, lights, or heting evies. If light progrms re enle, the ontroller utomtilly reserves the first 0-10V output to ontrol itionl lights. The lights tht re onnete to 0-10V outputs follow the sme vrition s the ongoing light progrm V Output Settings* *Aessile if 0-10V outputs re enle (se. 4.5). 0-10V Output Settings Show Settings of Output 3 Output Type Light Moe 0-10V 2. Set the following prmeters: Show Settings of Selet the proper 0-10V output. Note tht the first 0-10V output is utomtilly reserve to tivte itionl lights if light progrms re enle. Output Type Selet Light if lights re onnete to the selete 0-10V output.*0-10v outputs n only ontrol lights if light progrms re enle (se. 4.5) Light Progrm Settings 15. Light Settings* x. Progrm x * This menu is essile if light progrms re enle (se. 4.5). 2. Set the following prmeters: Animl Age This ge is the y t whih the selete light progrm strts eing use. Lights on 24 Hours When this funtion is enle, lights lwys sty lit while the progrm is running. Numer of Steps Selet the numer of steps performe within the selete progrm. *This prmeter is ville if the Lights on 24 Hours funtion is isle ove. Settings for Step #x Selet the proper step then set the following prmeters: *This prmeter is ville if the Lights on 24 Hours funtion is isle ove. Strt Time Selet the time t whih the selete step strts. Intensity Selet the intensity tht is rehe uring the selete step. Trnsition Selet the time frme tht is require for the lights to reh the speifie light intensity. Light Settings Progrm x Animl Age 1 ys Lights on 24 hours? No Numer of Steps 2 Disply Settings Step 01 Strt Time 6:00A Intensity 50 % Trnsition 0:30 (h:m) Exit: Press Bk Chnge: Press +/- Press to selet n item Moe Selet the type of signl tht is use y the selete output: 0-10V or 10-0V. 46 CC24-7 ELITE rev.23

47 9. CLOCK OUTPUTS The ontroller hs 8 outputs to ontrol vrious evies using the rel-time lok. Notes: To run lok output ontinuously, set ll of its strt n stop times to 12:00AM. An lrm sets off if lok progrm is not set properly; i.e., if n tivte progrm oes not hve ny strt time. This usully ours when the strt n stop times of progrm re ll set to the sme vlue (other thn 12:00AM). When this hppens, the ontroller keeps using the previous lok progrm until the efetive progrm is orrete. Refer to setion 4.5 to: - enle lok outputs; - enle lok progrms; - selet the proper time inrement for justing strt/run/stop times; - selet the proper operting moe for lok outputs 5-8. CLOCK OUTPUTS 1 TO 4 : Clok outputs 1-4 n use up to 4 progrms eh. Eh of the 4 progrms is ompose of 10 strt n stop times n the progrm seletion is me s funtion of the niml ge. Note tht progrm 1 utomtilly omes into effet one it is progrmme. Clok Output 1 PROG.1 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.2 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 Clok Output 2 PROG.1 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.2 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 Clok Output 3 PROG.1 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.2 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 Clok Output 4 PROG.3 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.3 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.3 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.4 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.4 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.4 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 CLOCK OUTPUTS 5 TO 8 Clok outputs 5 to 8 o not use the progrms ut they n operte in 3 ifferent wys: 1. Strt/Stop moe: With the Strt/Stop moe, lok outputs n operte oring to 10 ifferent strt n stop times. Fn Sttus ON OFF Strt Time Time Clok Strt/Stop Moe Stop Time Strt Time Time Stop Time 2. Strt/Run moe: With the Strt/Run moe, lok outputs n operte oring to 10 ifferent strt n run times. Fn Sttus ON OFF Strt Time Time Clok Strt/Run Moe Run Time Strt Time Run Time Time 3. Strt/Repet moe: With the Strt/Repet moe, the lok output opertes oring to timer whih is repete t regulr intervls. This timer is me of strt n run time. PROG.1 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.2 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.3 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 PROG.4 ON/OFF 1 ON/OFF 2 ON/OFF 3 ON/OFF 4 ON/OFF 5 ON/OFF 6 ON/OFF 7 ON/OFF 8 ON/OFF 9 ON/OFF 10 Fn Sttus ON OFF Time Clok Strt/Repet Moe Time etween repets Repet 1 Strt Time Run Time Time Refer to setion 4.5 of this mnul to hoose the esire operting moe for eh lok output. CC24-7 ELITE rev.23 47

48 16. Clok Times* x. Clok x Strt/Stop Time * Aville if lok outputs re enle (se. 4.5). Clok X Show Settings of Progrm 2 Animl Age 7 ys On Time 1 6:00A Off Time 1 6:00A On Time 2 6:00A Off Time 2 6:00A... On Time 10 6:00A Off Time 10 6:00A Operting Dy Settings: 1. Selet 16. Clok Times* 9. Dy of the Week * This menu is essile if lok outputs re enle (se. 4.5). Clok Time Dy of the Week Show Settings of Clok 1 Suny : Mony : Tuesy : Wenesy : Thursy : Stury : Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Show Settings of Selet progrm (for lok outputs 1 to 4 only). The 10 yles of the selete progrm re isplye. Animl Age Selet the ge t whih the progrm strts (for lok outputs 1 to 4 only). This menu is not ville for progrm 1 sine this progrm utomtilly strts one it is progrmme (y 0). Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Show Settings of Selet lok output. The operting ys of the selete lok output re isplye. Dys Put hek mrk to ientify on whih y(s) the lok output must e use. On / Off / Run Times Set the strt time n the stop time / or run time of eh yle. If 10 yles re not require, set the strt n stop times of unuse yles to the sme vlue (other thn 12:00AM) or set the run time to 0 min n 0 se. Numer of repets If the hosen lok output uses the Strt/Repet operting moe, selet how mny times the yle must e repete over the y. The output strts running t its strt time, performs the first yle n then repets it s require. Time etween repets If the hosen lok output uses the Strt/Repet operting moe, speify the perio of time etween yles (this perio of time must inlue the run time). 48 CC24-7 ELITE rev.23

49 10. RELATIVE HUMIDITY (RH) CONTROL Priniple of Opertion The ontroller offers ifferent options to ompenste for high/low humiity levels in the room. This setion esries the opertion of eh humiity ontrol metho RH Comp. on the Min. Ventiltion Intensity The humiity level n e erese y inresing the fns running time (or the fn spee) in minimum ventiltion. If vrile fns re use, their spee inreses uring the minimum ventiltion yles s the humiity level inreses; if On/Off fns re use, their running time inreses s the humiity level inreses. The e fns on time (or spee) is fully e when the humiity level exees the RH set point y 10%. Min Vent. On Time (or spee) Mximum On Time (or spee) Regulr On Time (or spee) Time (or spee) e RH Comp. on Minimum Ventiltion Intensity RH Set Point 10% RH Comp. with Heting Outputs RH Level (%) The ontroller n tivte heting units in timer moe to erese the humiity level. As the humiity level inreses, the heters On- Time inreses proportionlly to ompenste for the hnge. They reh their full On-Time when the humiity is t or ove RH Set Point + 10% s shown elow. On Time of the Heting Timer Mximum On Time Minimum On Time Off Time RH Comp. with Heting Outputs RH Set Point 10% RH Comp. on the Mist Output RH Level (%) The ontroller n stop mist units when the humiity level is too high. This pplies to fn stges with timer-se relys n ooling stges. The mist shutoff ours when the humiity level inreses ove the mist shutoff limit Settings 23. Controller Setup 1. Reltive Humiity Compenstion* * This menu is essile if the humiity proe is enle (se. 4.5). Reltive Humiity Compenstion Rel. Humiity SetPoint 65 % Use Minimum Vent. Comp? Yes A On Time 60 se A Spee 30 % Use Mist Shut Off? Yes Stop Misting t 90 % Use Heter Compenstion? Yes Heter Min. On Time 15 se Heter Mx. On Time 45 se Heter Off Time 285 se Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Reltive Humiity Set Point This is the humiity level ove whih the ompenstion strts. This prmeter rnges from 25 to 99%. Inrese the vlue to Off to isle ll humiity ompenstion funtions. Use Minimum Ventiltion Compenstion Selet Yes to ompenste high humiity levels with the fns run time or spee in minimum ventiltion. Ae Spee Spee tht is e to the vrile fns s uring the minimum ventiltion yles. This prmeter rnges from 1 to 100%. Selet Off to etivte this funtion. *This prmeter is ville if vrile outputs re enle (se. 4.5). Ae On Time Time tht is e to the fns run time uring the minimum ventiltion yles. This prmeter rnges from 0 to 900 seons. *This prmeter is ville if the vrile outputs re isle (se. 4.5). Use Mist Shut Off? Selet Yes to isle mist units (fn stges timer-se relys & ooling outputs) when the humiity level is too high. Stop Misting t Set the humiity level ove whih the stges timer-se relys n ooling stges stop. This prmeter rnges from 25% to 99%. Inrese the vlue to Off if you wnt to isle this funtion. Use Heter Compenstion? Selet Yes to tivte heting units in timer moe when the humiity level is too high. Min / Mx On Time Set the minimum n mximum run times of the heters timer. This prmeter rnges from 0 to 900 seons. Off Time Set the off time of the heting yle. This prmeter rnges from 0 to 900 seons. CC24-7 ELITE rev.23 49

50 11. ALARMS Alrm Log When n lrm ours, the lrm LED is turne on n the lrm is store in the lrm log menu, long with the time n te. The ontroller keeps in memory the lst 25 lrm onitions. 20. Alrm Log or press the Alrm Log shortut key Exit: Press Bk Alrm Log Logge on: Jn :03P Temperture Low F Proe #x Defetive Stti Pressure Proe Defetive Reltive Humiity Proe Defetive et. 2. Use the rrow keys to selet n lrm. The te n the time t whih the selete lrm onition ourre re isplye t the top of the isply Alrm Conitions & Settings The following setions esrie how the lrms re set off n how to just the lrm limits. Refer to the tle elow to see ll possile lrm onitions. Alrm Conitions Low Temp Alrm High Temp Alrm Low Pressure Alrm High Pressure Alrm Vr. Moule omm Inlet ommunition Rely ommunition Rely Progrmming Fult Clok 1-4 fult, Progrm #"x" Proe #x Defetive Outsie Proe Defetive Reltive Humiity proe Defetive Stti Pressure Proe Defetive Wter Spill Wter Moule Com Feeer run time Power Filure Zero rossing pop-up sreen: This lrm messge is isplye when there is instility in the ontroller power supply: Mke sure power supply is goo. Mke sure the flt le is onnete properly etween the top n ottom ors insie the ontroller. Mke sure oth power les re onnete properly insie the ontroller (min power or n power le etween min iruit or n upper iruit or). Another lrm sitution ours when power to the ontroller fils. In this se, the lrm rely is tivte. When the lrm rely is tivte, the normlly open ontt ( ) loses. Alrm Limits Set Point + Hi Offset Detetion of Temperture Alrms Hi T lrm Set Point Set Point Lo Offset Room T 50 CC24-7 ELITE rev.23

51 Temperture Alrms The following igrms explin how temperture lrms re etete: Room temperture Outoor T Compenstion on Temp. Alrms When the verge room temperture exees the high temperture lrm setting (Set Point + Hi Offset), high temperture lrm sets off. When the verge room temperture ereses elow the low temperture lrm limit (Set Point - Lo Offset), low temperture lrm sets off. The ritil temperture is the solute mximum llowle temperture in the room. Outsie Temperture Influene on Alrms: This feture vois flse lrms ue to wrm wether: the room temperture n exee the Hi temperture limit in the se where the outsie temperture is wrm enough. The room temperture must remin equl or lower thn Outsie T + Outsie Influene or lower thn the Set Point + Hi Offset, whihever is higher ut in every se, it must remin elow the ritil temperture, no mtter wht the outsie temperture is. Critil T Set Point + Hi Offset Set Point Lo Offset Out.T Influene Outsie temperture Critil lrm limit High T lrm limit Low T lrm limit Time Legen Alrm limits Outsie temperture Temperture lrm No lrm Outsie temperture influene (no lrm) 23. Controller Setup 5. Alrm Settings 1. Temperture Temperture Alrm Settings Low Offset Temperture 10.0 F High Offset Temperture 15.0 F Outsie Influene 5.0 F Critil Temperture 90.0 F High Breker Alrm F 2. Set the following prmeters: Low High Temperture Offset The Hi n low offsets re the numer of egrees elow n ove the set point t whih temperture lrm sets off. The low temperture limit rnges from 20 F to 0.5 F (11.1 to 0.3 C) elow the set point (Lo Offset). The high temperture limit rnges from 0.5 F to 35 F (0.3 to 19.4 C) ove the set point (Hi Offset). Outsie Influene The outsie temperture influene is the numer of egrees tht re e to the outsie temperture to voi flse lrms on wrm ys. Refer to the previous igrm. Critil Temperture The ritil temperture is the solute mximum temperture tht is llowe in the room. High Breker Alrm If the temperture of the min reker is monitore y proe, set the proe temperture over whih reker temperture lrm must soun. *Aessile if the reker s monitoring funtion is enle in setion 4.5. Instll the reker s proe lose to the reker ox, not insie the ox! CC24-7 ELITE rev.23 51

52 Stti Pressure Alrms The ontroller n generte n lrm if the stti pressure ereses elow the low pressure limit or if it exees the high pressure limit. The lrm onition must e mintine uring user-efine ely efore the lrm sets off. Lo Stti Pressure Alrm: You n ssign rely tht will e tivte if Low Stti Pressure Alrm ours. This rely my e use to tivte fn for instne. When low stti pressure lrm ours, this rely turns on for 15 minutes. If the stti pressure level is still elow the Low Pressure Limit fter this ely hs elpse, the rely keeps running for nother 15 minutes, up until the pressure level returns in the norml rnge. Low Stti Pressure Alrm Curve The ontroller n utomtilly hnge the low stti pressure lrm limit with time. With the low SP lrm urve, you n progrm 3 ifferent low pressure lrm limits n the moment t whih eh limit strts eing use is efine s funtion of the niml ge. Refer to the instlltion setup setion of this mnul to enle the Low SP Curve (setion 4.5). HI Stti Pressure Alrm: When high stti pressure lrm ours, the ontroller n open vent oors n the tunnel urtin. The urtin or vent oors open uring user-efine ely (Open-Time) n then sty still for 15 minutes (this time inlues the Open-Time). If the pressure level still exees the Hi Stti Pressure Limit fter 15 minutes, the sme yle strts over gin, up until the pressure level goes k in the norml rnge SP Alrm Settings: 23. Controller Setup 5. Alrm Settings 2. Stti Pressure* 1. Low n High Limits * This menu is essile if the stti pressure sensor is enle (se. 4.5). or Stti Pressure Lo n Hi Alrm Limits Low Alrm High Alrm Low Dely High Dely Low SP limit 1 : Low SP limit 2 : Animl Age 2 : Low SP limit 3 : Animl Age 3 : High Alrm Low Dely High Dely 2. Set the following prmeters:.10 WC.150 WC 600 se 300 se.02 WC.02 WC 20 ys.02 WC 40 ys.150 WC 600 se 300 se Low /High Pressure Alrm Set pressure limits to the esire vlues (from 0.00 to 0.40 WC) or selet Off to isle the low pressure lrm. If the Low SP lrm urve is use, set ll 3 low pressure lrm limits. *Low SP limits 2-3 re only essile if the Low SP lrm urve is enle in the Instlltion Setup (se. 4.5). Animl Age If the Low SP lrm urve is use, set the niml ge t whih eh low pressure lrm limit strts eing use (note tht the first lrm limit is use when the nimls re younger thn the ge speifie for lrm limit 2. *Aessile if the Low SP lrm urve is enle in the Instlltion Setup (se. 4.5). Low/High Dely Set the ely over whih the lrm onition must e mintine for n lrm to set off. Set this ely seprtely for the Hi n Lo stti pressure lrms Low SP Alrm Rely 23. Controller Setup 5. Alrm Settings 2. Stti Pressure* 2. Low Alrm Rely * This menu is essile if the stti pressure sensor is enle (se. 4.5). Low Stti Pressure Alrm Rely Put hek mrk to ientify the rely tht is use in se of low pressure lrm Hi Stti Pressure Alrm Settings 23. Controller Setup 5. Alrm Settings 2. Stti Pressure* 3. High Alrm * This menu is essile if the stti pressure sensor is enle (se. 4.5). Hi Stti Pressure Alrm Settings Open Vent Door 30 se 2. Selet the moving time of the urtin n/ or vent oors* when stti pressure lrm ours. The urtin or vent oor opens or loses uring this ely every 15 minutes, up until the stti pressure returns in the norml rnge. *For stti pressure-se vent oors n urtin only. 52 CC24-7 ELITE rev.23

53 Wter Spill Alrms A wter spill lrm sets off when the wter onsumption exees ertin limit. This limit n e juste from 0 to 10,000 gllons or liters per 15 minutes. The lrm is tivte if greter mount of wter is etete within the 15 minute intervl. 23. Controller Setup 5. Alrm Settings 3. Wter Consumption* * This menu is essile if wter meters re enle (se. 4.5). Wter Spill Alrm Settings Feeer Alrms An lrm sets off when the ontinuous feeer run time is too high. When this type of lrm ours, the lrm rely swithes n the ontroller opens the feeer rely to stop the feeer motor. 23. Controller Setup 5. Alrm Settings 4. Feeer Mximum Run Time Feeer Alrm Settings 1:30 (h:m) Wter Meter 1 Wter Meter 2 Wter Meter 3 Wter Meter 4 Wter Meter 5 Wter Meter 6 Wter Meter 7 Wter Meter 8 Wter Meter 9 Wter Meter gl 10 gl 10 gl 10 gl 10 gl 10 gl 10 gl 10 gl 10 gl 10 gl 2. Set the following prmeters: Mximum Run Time Set the mximum onseutive run time of the feeer motor. This prmeter rnges from 0:00 to 23:59 h:m. Stop t Mx Run Time? Selet Yes to stop the feeer when feeer run time lrm ours (the feeer rely opens). Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set eh the mximum wter onsumption per perio of 15 minutes of eh wter meter. Restrt Feeer If feeer lrm is urrently tive, the messge Restrt Feeer is isplye. Selet Yes to reset the feeer lrm n to restrt the feeer. CC24-7 ELITE rev.23 53

54 12. MONITORING FUNCTIONS Current Conitions The urrent onition menus give quik view of the tul onitions in the rn: 1. Current Conitions 2. Selet the esire onition menu: 1. Current Conition To see the urrent proe temperture reing n other useful piees of informtion. The ontroller utomtilly selets this menu fter 4 minutes of intivity. Current Conition Current Temp. Set Point 80.0 F Animl Age 5 ys Stti Pressure.02 WC Minimum Vent. On Time 0:30 (m:s) Light Intensity 80 % Vent Door Opening 10 % Vent Door 2 Opening 0 % Insie Temp. Proe F (...) Insie Temp. Proe F Reltive Humiity 30 % Averge House Temperture 79.0 F Outsie Temperture 58.0 F History The input reings re logge in the history menus t minight every y. These histories re reset when new th strts. AVERAGE HOUSE T : The ily minimum n mximum reings of the verge room temperture re isplye for the pst 75 ys. 1. Selet 2. Averge House Temperture Averge House Temperture 75 ys Temperture 77.9 F Dte Minimum Mximum De :O5A :34A 78.2 De :19A :58A 79.3 De :28A :34P 80.1 De :21P :12P 78.2 De :34A :14A 79.3 De :14A :32P 78.2 De :52A :28P 78.7 De :39P :33P 79.2 INDIVIDUAL PROBE TEMPERATURE: The ily minimum n mximum temp erture reings of eh iniviul proe re isplye for the pst 7 ys. OUTSIDE TEMPERATURE: The ily minimum n mximum reings of the outsie temperture proe re isplye for the pst 75 ys. 1. Selet 4. Outsie Temperture* * This menu is essile if the outsie T sensor is enle (se. 4.5). Outsie Temperture (75 ys) Temperture 68.4 F Dte Minimum Mximum De :O5A :34A 68.2 De :19A :58A 69.3 De :28A :34P 60.1 De :21P :12P 68.2 De :34A :14A 69.3 De :14A :32P 68.2 De :52A :28P 68.7 De :39P :33P 69.2 RELATIVE HUMIDITY: The ily minimum n mximum reings of the humiity proe re isplye for the pst 75 ys. 1. Selet 5. Reltive Humiity* Exit: Press Bk Press to selet n item 1. Selet 3. Iniviul Proe Temperture * This menu is essile if humiity sensor is enle (se. 4.5). 2. Ative Sensors To see wht temperture sensors re urrently use to mesure the verge room temperture. 3. Current Ative Relys To see whih relys re urrently tive. Selet All to view ll tive relys; selet Fn/Cool to see the relys of fn n ooling stges only Current Ative Relys Show Ative Relys : All (or Fn/Cool) Iniviul Proe Temperture (7 ys) Disply Proe 1 Temperture 77.0 F Dte Minimum Mximum De :O5A :34A 78.2 De :19A :58A 79.3 De :28A :34P 80.1 De :21P :12P 78.2 De :34A :14A 79.3 De :14A :32P 78.2 De :52A :28P 78.7 De :39P :33P 79.2 WATER CONSUMPTION: The ily wter onsumption of eh wter meter is isplye for the pst 60 ys. The totl onsumption is isplye s well. 1. Selet 18. Wter Consumption* Selet the esire wter meter * This menu is essile if wter meters re enle (se. 4.5). Wter Consumption of Meter X (60 ys) Totl Toy Mrh Mrh Mrh lit 5 lit 4 lit 5 lit 6 lit Exit: Press Bk Press to selet n item 54 CC24-7 ELITE rev.23

55 HEATER RUN TIME: The ily run times of eh heting outputs re isplye for the pst 7 ys. The totl run time is isplye s well. 1. Selet 19. Heter Run Time Selet the esire heting stge Heter X Run Time (7 ys) Monitoring the Animl Age & Numer Animl Age: The ontroller uses the niml ge s referene to fin its position in the vrious urves (minimum ventiltion n set point urves). It lso uses this ge to tivte the proper light progrm n to limit the tunnel ventiltion level. Using the niml ge is optionl, refer to setion 4.5 to enle or isle niml ge funtions. New Mortlity Post up the mortlities s they our. One you hve entere vlue, the ontroller vlites it n isplys 0 fterwrs. The ontroller then s this vlue to the totl numer of mortlities n removes it from the remining niml ount. Totl Mortlity This is the totl numer of mortlities sine the eginning of the th. This vlue is isplye s reing n nnot e moifie. Totl Toy Mrh Mrh Mrh Exit: Press Bk Press 1000 min 600 min 600 min 450 min 550 min to selet n item Numer of nimls: At the eginning of th, you must speify wht is the initil numer of nimls in the room. You must then post up every vrition in the numer of nimls (mortlities & ulle nimls). This wy, the ontrollers keeps trk of the numer of remining n e niml within th. ALL histories re reset when new th strts. Remining Count This is the totl numer of nimls remining in the house. Initil Count - Totl Mortlity. Strt New Bth When new th strts the ontroller resets ll histories. The remining ount goes k to the initil ount n the totl numer of mortlities goes k to zero. One you hve nswere Yes to the Strt New Bth question, the ontroller vlites the nswer then isplys No gin mening the new th hs just strte. 17. Animl Age & Mortlity Animl Age & Mortlity Animl Age 5 ys Initil Count 0 New Mortlity 0 Totl Mortlity 0 Remining Count 0 Strt New Bth No Exit: Press Bk Chnge: Press +/- Press to selet n item 2. Set the following prmeters: Animl Age This prmeter rnges from -5 to 450 ys. Negtive y vlues re use to prepre the house efore the nimls rrivl. *This prmeter is ville if the niml ge funtion is enle in setion 4.5. Initil Count Enter the initil numer of nimls t the eginning of the th. CC24-7 ELITE rev.23 55

56 12.4. Messge Center Use the messge enter s reminer for the mintenne of your equipment. You must first enter the frequeny t whih your vrious serviing tivities must e performe. The ontroller will then vise you when the serviing time hs elpse. When this hppens, the ontroller turns on the Messge Center sttus LED n posts messge telling the nture of the serviing tivity tht nees to e exeute in the Messge Center menu Messge Log The Messge Log menu tells whih serviing tivity nee to e one. When the Messge Center sttus LED is lit when messge is present in the Messge Log menu. The ontroller keeps in memory the lst 25 events. 24. Messge Center 1. Messge Log or press F Clering the Messge Log One you hve omplete the serviing tivities, ler the messge logs s follows: 24. Messge Center 3. Cler Messge Center 2. Selet Yes to ler the messges tht re urrently present in the Messge Log menu. Cler Messge Center Do you relly wnt to ler ll the messges reore? Serviing Sheule Speify the frequeny t whih your serviing tivities must e performe : No Rely Run Time The ontroller keeps in memory the running time of the first 50 relys (relys 1-50). Follow this proeure to see the relys run times. 25. Rely Run Time 2. Show Rely Run Time Rely #1: Rely #2: Rely #3: Rely #4: Rely #5: Rely #6: Rely #7: Rely #8: Rely #9: Rely #10: Rely #11: Exit: Press Bk Show Rely Run Time 1250 hours hours 1550 hours 540 hours hours 9920 hours 820 hours 4580 hours 7821 hours 0 hours 0 hours Messge Log Logge on: Jn :03P Temperture Low F Ajust Overrie Thermostts Chek Ctrl Alrm output 24. Messge Center 2. Messge Settings Messge Center Settings Externl Input 500 hours Clering the Rely Run Time: Follow this proeure to ler the run time of speifi rely (mongst rely 1 to rely 50). 25. Rely Run Time 1. Cler Rely Run Time Aj. Overrie Thermostts Chek Ctrl Alrm Output 7 ys 3 month 2. Put hek mrk to ler the run time history of rely then nswer Yes to the Cler Run Time question. Exit: Press Bk 2. Set the following prmeters: To isle monitoring funtion, erese the prmeter until the wor Off ppers. Externl Input Selet fter how mny hours of opertion the externl input must e heke. Cler Rely Run Time of selete Rely Cler Run Time : No Ajust Overrie Thermostts / Chek Control Alrm Output Set the frequeny t whih oth of these mintenne tivities must e performe. The ountown strts from the moment the ontroller is powere up. 56 CC24-7 ELITE rev.23

57 13. TECHNICAL SPECIFICATIONS Type...CC24-7 ELITE Min supply fuse F A, fst-low Min supply/frequeny...120/240 V, 50/60Hz 0-10V outputs # V, 30mA soure mx. Preision on 0-10V outputs...±1 % 14V Outputs...14 V ± 10%, regulte, 250mA mx. Alrm Contt...ON/OFF output, 24VDC or AC, 0.15A. Enlosure...ABS, moisture n ust-tight. Operting temperture...32 to 104 F (0 to 40 C). Inoor use only. Storge temperture...5 to122 F (-15 to 50 C) Amient reltive humiity...mx. 95% Reltive humiity input ma Pressure input ma Temperture 77 F (25 C), NTC CC24-7 ELITE rev.23 57

58 14. TRANSFER MENU Sreen Contrst 1. Simultneously press n hol the right n left rrow keys for 5 seons to isply the trnsfer menu. 2. Choose 6. Contrst n press Enter. 3. Set the sreen ontrst to the esire intensity then press Enter to vlite. 4. Simultneously press n hol the right n left rrow keys for 5 seons to exit from the trnsfer menu Communition Spee 1. Simultneously press n hol the right n left rrow keys for 5 seons to isply the trnsfer menu. 2. Choose 5. Comm Spee n press Enter. 3. Set the ommunition spee to the esire vlue: selet the high spee moe if the ontroller uses the A-BOX ommunition system or selet the low spee if it uses AGNET. 4. Simultneously press n hol the right n left rrow keys for 5 seons to exit from the trnsfer menu. USB rive Upte/Bkup Proess The USB rive llows upgring the firmwre or softwre of your ontroller. It n lso e use to mke kup of your ontroller settings or to opy these settings on nother ontroller of the sme type. Turn off power eh time you open the ontroller s enlosure. This prevents ientl exposure to res of high voltge. 1. Turn off power to the ontroller. 2. Lift the lthes to open the front oor of the ontroller. 3. Insert the USB rive in the onnetor ehin the front oor. 4. Close the front over n repply power to the ontroller. 5. Simultneously press n hol the right n left rrow keys for 5 seons to isply the trnsfer menu. 6. Selet the esire option: Trnsfer Menu 1. MemoryCr -> Control 2. Control -> MemoryCr 3. Upte Firmwre 4. Sve Event Buffer 5. Comm Spee 6. Contrst 1. MemoryCr -> Control Choose 1. MemoryCr -> Control to lo new onfigurtion file into your ontroller. This trnsfer will upte your ontroller s softwre n prmeter settings. When seleting this option, list of ll onfigurtion files lote on the r is isplye (*.DMP files). Selet the esire file n then simultneously press the up n own-rrow keys to strt the trnsfer. Note tht the ontroller n only re the files tht re lote t the root of the USB rive. It nnot ess ny su-iretory! 2. Control -> MemoryCr Choose 2. Control -> MemoryCr to sve your ontroller settings on the USB rive n press Enter. The sving proess will strt s soon s you enter this menu. The ontroller will rete new SAVE~1. DMP file t the root of the USB rive. If this file nme lrey exists, it will e sve uner ifferent nme ( SAVE~2.DMP for instne). This wy, the ontroller will never erse file on the r. 3. Upte Firmwre Choose 3. Upte Firmwre to ownlo new firmwre file into your ontroller. This proess will not ffet your prmeter settings. When seleting this option, list of ll firmwre files lote on the USB rive is isplye (*.PKG files). Selet the esire file n then simultneously press the up n own-rrow keys to strt the trnsfer. Note tht the ontroller n only re the files tht re lote t the root of the USB rive. It nnot ess ny su-iretory! 4. Sve Event Buffer Choose 4. Sve Event Buffer to sve the event uffer of the ontroller on your USB r. The file will hve *.txt extension. (USB r only!) Simultneously press n hol the right n left rrow keys for 5 seons to exit from the trnsfer menu. Remove the USB rive from the onnetor when the trnsfer is over! 58 CC24-7 ELITE rev.23

59 15. INSTALLATION REPORT CLIENT Nme: Aress: City: Phone: Fx: INSTALLER Nme: Aress: City: Phone: Fx: CC24-7 ELITE rev.23 59

60 Instlltion Setup Worksheet (se. 4.5). Prmeter Rnge Your settings Cler Alrms Yes / No Numer of T Proes 1 to 8 Numer of Wter Meters 0 to 10 Numer of Relys 10 to 100 Numer of Inlets 0 to 10 Numer of Fn Stges 1 to 16 Numer of Cooling 0 to 4 Numer of Progrms None / / / Numer of Light Progrms 0 to 8 Numer of Heters 0 to 8 Numer of Nturl Zones 0 to 4 Numer of Cloks 0 to 8 # of Progrms - Clok Output 1 1 to 4 # of Progrms - Clok Output 2 1 to 4 # of Progrms - Clok Output 3 1 to 4 # of Progrms - Clok Output 4 1 to 4 Clok Output 5 Moe Strt-Stop / Strt-Run / Strt-Repet Clok Output 6 Moe Strt-Stop / Strt-Run / Strt-Repet Clok Output 7 Moe Strt-Stop / Strt-Run / Strt-Repet Clok Output 8 Moe Strt-Stop / Strt-Run / Strt-Repet Clok Inrements 1, 5 or 10 min Use Night Set Point? Yes / No Use Set Point Curve? Yes / No Use Minimum Ventiltion Curve? Yes / No Use Heter Offset Curve? Yes / No Use Animl Age funtion? Yes / No Use Heter Progrms? Yes / No Use Heter Hi / Lo Fire? Yes / No Use Tunnel? Yes / No Tunnel Moe : Time / Stti Pressure Vent Door Trnsition moe : Open / Stti Pressure / As is Tunnel Pre-opening Type Norml / Tunnel Help Tunnel Pre-opening Time n/ seons Multiple tunnel stges with ge? Yes / No Use tunnel urtin in nturl? Yes / No Use Stir Fns? Yes / No Use Vriles? Yes / No Vrile 1 Minimum Spee : n/ % 60 CC24-7 ELITE rev.23

61 ... Instlltion Setup Worksheet (se. 4.5). Prmeter Rnge Your settings Vrile 2 Minimum Spee : n/ % Use Rmping on Stge 1? Yes / No Use Rmping elow Set Point? Yes / No Stge 1 Rmping Dely (vne) n/ seons Stge 2 Rmping Dely (vne) n/ seons Outsie T Set Point (vne) n/ Rmping yle (vne) n/ seons Use Outsie Temperture? Yes / No Use Reltive Humiity Proe? Yes / No Use Stti Pressure (SP) Proe? Yes / No SP Set 2 - Vent Doors None / Stge / Outsie T Vent Doors' Pre-opening Moe Auto / Mnul Pre-opening ely for Vent Doors n/ seons Pre-opening ely for Atti Vents n/ seons SP Set 2 - Tunnel Curtin None Stge Use SP Compenstion on Inlets? Yes / No Sen Temperture Compenstion eh n/ : (m:s) Use Curve on Low SP Alrms? Yes / No Monitor reker temperture? Yes / No Vent Door Moe SP / Potentiometer / Timer Use 2n Inlet? Atti Moe 2n Inlet Type 2n Inlet Moe Atti/2n Inlet Proe Atti / 2n inlet SP / Time Siewll / Tunnel SP / Time Room / Iniv. Shown on LED Disply Temperture n: - Stti pressure -Vent oor position CC24-7 ELITE rev.23 61

62 Proe Assignment Worksheet T Proes OUTPUTS Avg Room T Progrm Progrm Progrm Progrm Heter 8 Hi Progrm Progrm Progrm Progrm Heter 8 Progrm Progrm Progrm Progrm Heter 7 Hi Progrm Progrm Progrm Progrm Heter 7 Progrm Progrm Progrm Progrm Heter 6 Hi Progrm Progrm Progrm Progrm Heter 6 Progrm Progrm Progrm Progrm Heter 5 Hi Progrm Progrm Progrm Progrm Heter 5 Progrm Progrm Progrm Progrm Heter 4 Hi Progrm Progrm Progrm Progrm Heter 4 Progrm Progrm Progrm Progrm Heter 3 Hi Progrm Progrm Progrm Progrm T Proes OUTPUTS Heter 3 Progrm Progrm Progrm Progrm Heter 2 Hi Progrm Progrm Progrm Progrm Heter 2 Progrm Progrm Progrm Progrm Heter 1 Hi Progrm Progrm Progrm Progrm Heter 1 Progrm Progrm Progrm Progrm Inlet 1 Inlet 2 Inlet 3 Inlet 4 Inlet 5 Inlet 6 Inlet 7 Inlet 8 Inlet 9 Inlet V Output V Output V Output V Output 4 Nturl Zone 1 Nturl Zone 2 Nturl Zone 3 Nturl Zone 4 Cooling 1 Cooling 2 Cooling 3 Cooling 4 Min Breker T Atti Vent 62 CC24-7 ELITE rev.23

63 63 CC24-7 ELITE rev.23 CC24-7 ELITE Relys Desription

64 Rely Assignment Worksheet HEATING OUTPUTS (relys 1 to 50) RELAY # Heter 8 Hi Heter 8 Hi Heter 8 Hi Heter 8 Hi Heter 8 Heter 8 Heter 8 Heter 8 Heter 7 Hi Heter 7 Hi Heter 7 Hi Heter 7 Hi Heter 7 Heter 7 Heter 7 Heter 7 Heter 6 Hi Heter 6 Hi Heter 6 Hi Heter 6 Hi Heter 6 Heter 6 Heter 6 Heter 6 Heter 5 Hi Heter 5 Hi Heter 5 Hi Heter 5 Hi Heter 5 Heter 5 Heter 5 Heter 5 Heter 4 Hi Heter 4 Hi Heter 4 Hi Heter 4 Hi Heter 4 Heter 4 Heter 4 Heter 4 Heter 3 Hi Heter 3 Hi Heter 3 Hi Heter 3 Hi Heter 3 Heter 3 Heter 3 Heter 3 Heter 2 Hi Heter 2 Hi Heter 2 Hi Heter 2 Hi Heter 2 Heter 2 Heter 2 Heter 2 Heter 1 Hi Heter 1 Hi Heter 1 Hi Heter 1 Hi Heter 1 Heter 1 Heter 1 Heter CC24-7 ELITE rev.23

65 HEATING OUTPUTS (relys 51 to 100) RELAY # Heter 8 Hi Heter 8 Hi Heter 8 Hi Heter 8 Hi Heter 8 Heter 8 Heter 8 Heter 8 Heter 7 Hi Heter 7 Hi Heter 7 Hi Heter 7 Hi Heter 7 Heter 7 Heter 7 Heter 7 Heter 6 Hi Heter 6 Hi Heter 6 Hi Heter 6 Hi Heter 6 Heter 6 Heter 6 Heter 6 Heter 5 Hi Heter 5 Hi Heter 5 Hi Heter 5 Hi Heter 5 Heter 5 Heter 5 Heter 5 Heter 4 Hi Heter 4 Hi Heter 4 Hi Heter 4 Hi Heter 4 Heter 4 Heter 4 Heter 4 Heter 3 Hi Heter 3 Hi Heter 3 Hi Heter 3 Hi Heter 3 Heter 3 Heter 3 Heter 3 Heter 2 Hi Heter 2 Hi Heter 2 Hi Heter 2 Hi Heter 2 Heter 2 Heter 2 Heter 2 Heter 1 Hi Heter 1 Hi Heter 1 Hi Heter 1 Hi Heter 1 Heter 1 Heter 1 Heter CC24-7 ELITE rev.23 65

66 OTHER OUTPUTS (relys 1 to 50) Fn 1 Fn 2 Fn 3 Fn 4 Fn 5 Fn 6 Fn 7 Fn 8 Fn 9 Fn 10 Fn 11 Fn 12 Fn 13 Fn 14 Fn 15 Fn 16 Cooling 1 Cooling 2 Cooling 3 Cooling 4 Nturl 1 Nturl 2 Nturl 3 Nturl 4 Tun. Curtin Vent Doors RELAY # 2n inlet output (use s siewll vent, tunnel urtin or tti vent) OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO Clok 1 Clok 2 Clok 3 Clok 4 Clok 5 Clok 6 Clok 7 Clok 8 Lo Pressure Alrm Bkup Rely Feeer 66 CC24-7 ELITE rev.23

67 OTHER OUTPUTS (relys 51 to 100) RELAY # Fn 1 Fn 2 Fn 3 Fn 4 Fn 5 Fn 6 Fn 7 Fn 8 Fn 9 Fn 10 Fn 11 Fn 12 Fn 13 Fn 14 Fn 15 Fn 16 Cooling 1 Cooling 2 Cooling 3 Cooling 4 Nturl 1 Nturl 2 Nturl 3 Nturl 4 Tun. Curtin Vent Doors 2n inlet output (use s siewll vent, tunnel urtin or tti vent) OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO OPN CLO Clok 1 Clok 2 Clok 3 Clok 4 Clok 5 Clok 6 Clok 7 Clok 8 Lo Pressure Alrm Bkup Rely Feeer CC24-7 ELITE rev.23 67

68 MAIN MENU SUB-MENUS 1 Current Conitions 1 Current Conitions 2 Ative Sensors 3 Current Ative Relys 2 Averge House Temperture 3 Iniviul Proe Temperture 4 Outsie Temperture 5 Reltive Humiity 6 Progrm Seletion 7 Temperture Set Point 8 Minimum Ventiltion 9 Curve Settings 1 Temperture Set Point 2 Minimum Ventiltion (Vr./On Time) 3 Minimum Ventiltion Vrile 2 4 Heter 1 Strt Temperture 5 Heter 1 Hi Strt Temperture 6 Heter 2 Strt Temperture 7 Heter 2 Hi Strt Temperture Heter 8 Strt Temperture 20 Heter 8 Hi Strt Temperture 10 Inlet Comp. / Vent Doors & SP 11 Tunnel Curtin 12 Atti Settings MAIN MENU SUB-MENUS 12 Vent Doors 2 / Stti Pressure 12 Tunnel Curtin 2 13 Heter Strt/Stop Temperture 14 Fn/Cool./Nt. Temp. Settings 1 Fn Temperture Settings 2 Cooling Temperture Settings 3 Nturl Temperture Settings 15 Light Settings 1 Progrm 1 2 Progrm 2 3 Progrm 3 4 Progrm 4 16 Clok Time 1 Clok 1 2 Clok 2 3 Clok 3 4 Clok 4 5 Clok 5 6 Clok 6 7 Clok 7 8 Clok 8 9 Dy of the week 17 Animl Age & Mortlity 18 Wter Consumption 1 Wter Meter 1 2 Wter Meter 2,,, 10 Wter Meter Heter Run Time 1 Heter 1 2 Heter 1 Hi 3 Heter 2 4 Heter 2 Hi,,, 15 Heter 8 16 Heter 8 Hi MAIN MENU SUB-MENUS 20 Alrm Log V Output Settings 22 Rely n Proe Assignment 1 Relys for Stges 2 Relys for Heters 3 Rely for Tunnel Curtin 4 Relys for Vent Doors 5 Relys for Atti/2n inlet 6 Relys for Cloks 7 Relys for Coolings 8 Relys for Bkup 9 Relys for Nturls 10 Rely Timer/Vrile Settings 11 Relys for feeer 12 Proes for Stges 13 Proes for Heters 14 Proes for Coolings 15 Proes for Nturls 16 Proes for Inlets 17 Proes for 0-10V Outputs 18 Proes for the min reker 19 Proes for Atti/2n Inlet 20 Copy Pste 23 Controller Setup 1 Reltive Humiity Compenstion 2 Instlltion 3 Proe Clirtion 4 Time n Dte 5 Alrm Settings 6 Dy / Night Time 7 Psswor 8 Units 9 Test Moe 10 Version 24 Messge Center 25 Rely Run Time 68 CC24-7 ELITE rev.23

69 CC24-7 ELITE rev.23 69

70 A 16. INDEX Age see Animls Alrms Alrm onitions & settings 50 Alrm log 50 Reset the lrm log 14 Clok progrm lrm 47 Critil temperture lrms 51 Low SP lrm urve Ativtion 16 Priniple of opertion 52 Settings 52 Zero-rossing sreen 50 Animls Animl ge funtions 14 Informtion 55 Multiple tunnel stge with ge 15 Posting new mortlities 55 Strting new flok 55 Assignment Proe ssignment 17 Rely Assignment 18 Atti vent Ativtion 16 Opertion & settings Pre-opening 16 Proe ssignment 17 Rely ssignment 19 B Bkup Mking kup of the ontroller 58 Bkup rely ox 20 Birs see Animls Breker Monitoring the reker s T Ativtion 16 Hi temperture lrm limit 51 Proe ssignment 17 C Clirtion Proe lirtion 17 Celsius units 13 Clok Disply : AM/PM or 24hours 13 Setting the time n te 12 Clok outputs Ativtion 14 Opertion & settings 47 Rely ssignment 20 Time inrement 14 Common relys see Relys Communition spee 58 Compenstion Humiity omp. see Reltive humiity Inlet ompenstion: se on SP Priniple of opertion 33 Inlet s T & pressure ompenstions Ativtion 16 Priniple of opertion 33 Min. ventiltion ompenstion 25 Conitions 54 Connetions 7 Contrst 58 Contrst (LCD sreen) 11 Controller Fetures 5 Instlltion setup Lotion of the ontrols 11 Mounting instrutions 7 Progrm version 21 Tehnil speifitions 57 Cooling outputs (mists) Ativtion 14 Priniple of opertion 40 Proe ssignment 17 Rely ssignment 20 Settings 40 Shutoff on hi humiity levels 49 Copy & Pste funtion Controller progrms 13 Fn stges relys 19 Heters urves 44 Current onitions 54 Curtins see Tunnel or Nturl Ventiltion Curves Heters offset urve Ativtion 14 Copy & Pste 44 Priniple of opertion 44 Settings 44 Minimum ventiltion - On Time urve Ativtion 14 Priniple of opertion 24 Minimum ventiltion - Spee urve Ativtion 14 Priniple of opertion 24 Settings 24 Set point urve Priniple of opertion 22 D Dte Setting the time n te 12 Dy / Night Dy/night times 12 Night set point Ativtion 14 Priniple of opertion 22 Disply Re le isply Lotion 11 Unit seletion 16 Sttus les 11 E Eletril speifitions 57 Externl input 56 F Fhrenheit units 13 Fn stges 0-10V ventiltion Priniple of opertion 27 Proe seletion 17 Settings 28 Ativtion 14 Min. Vent. see Minimum ventiltion Optionl ventiltion stges see 0-10V Priniple of opertion 26 Proe ssignment 17 Rely ssignment 18 Settings 27 Stir fns see Stir fns Timer-se relys Ativtion 18 Priniple of opertion 18, 26 Settings 19 Trnsition etween stges 1 n 2 Priniple of opertion 26 Settings 27 Vrile fns Ativtion 15, 19 Minimum fn spee 15 Priniple of opertion 26 Feeer Alrm settings 53 Rely ssignment 20 Fire see Heters G Gllons 13 H Heters 0-10V het mts Opertion & settings 45 Proe seletion 17 Ativtion 14 Copy & Pste urve see Curves Heter progrms CC24-7 ELITE rev.23

71 Heters offset urve see Curves Humiity ompenstion Priniple of opertion 49 Settings 49 Lo/Hi fire Ativtion 14 Opertion & Settings Opertion & Settings Proe ssignment 17 Rely ssignment 18 RH ompenstion see Rel. humiity Run times 55 History House temperture see Temperture Humiity see Reltive humiity I Inlet Atti Inlet see Atti Inlet (onnete to SB Moules) Ativtion 14 Current opening 54 Inlet s T & pressure ompenstion Ativtion 16 Priniple of opertion 33 Opertion & settings 32, 33 Proe ssignment 17 Inputs 5, 14 Inset filter 8 Instlltion setup Worksheet 60, 61 Instller psswor 12 L LCD sreen Contrst justment 11, 58 Les Le isply 11 Unit seletion 16 Sttus les 11 Lights (0-10V) Ativtion 14, 46 Current intensity 54 Priniple of opertion 46 Settings 46 Liters 13 Logs see lso History Alrm log 50 M Mnul moe see Test moe Mesuring units 13 Memory r Trnsfer proess 58 Messge enter 56 Minimum ventiltion Compenstion 25 Min. vent. urve see Curves Priniple of opertion 23 Rmping funtion Priniple of opertion 25 Settings 15 RH ompenstion see Rel. Humiity Settings 23 Spee urve see Curves Mist see Cooling outputs Mounting instrutions 7 N Nturl ventiltion zones Ativtion 14 Curtins rely ssignment 19 Priniple of opertion 41 Proe ssignment 17 Settings 42 Tunnel urtin in nturl ventiltion Ativtion 15 Night see Dy / Night O Outputs 5 Outputs (0-10V) see Lights, Heters, or Fn stges Outsie T see Temperture P Prmeter justment 11 Psswor 12 Potentiometer (for inlets) Ativtion 16 Pressure see Stti pressure Proe Connetion 7 Extension 7 Proes Ativtion 14, 15 Assignment Mke the ssignment 17 Clirtion 17 Current tive proes 54 Current reings 54 Progrms Ativtion 14 Clok progrms see Clok outputs Copy/pste progrm settings 13 Heter progrms 14 Light progrms see 0-10V outputs Progrm seletion 13 Progrm version (ontroller s) 21 R Rmping see lso Curves Min. ventiltion rmping Ativtion & settings 15 Priniple of opertion 25 Reltive humiity (RH) History 54 RH Compenstion Priniple of opertion 49 Settings 49 RH sensor Ativtion 15 Clirtion 17 RH set point 49 Relys Ativtion 14 Bkup rely ox 20 Common relys Priniple of opertion 20 Seletion 20 Copy/Pste 19 Current tive relys 54 Low SP lrm rely 52 Rely ssignment Worksheet 64 Rely pnels 18 Run time history 56 Stir fns relys Ativtion 15 Assigning stir fn relys 18 Priniple of opertion 18 Timer-se relys Opertion & Ativtion 18 Settings 19 Reset (vent oor s position) 37, 38 Room temp. see lso Temperture Proe ssignment 17 S Sreens see LED or LCD Disply Seson seletion 13 Sensors see Proes Set point see Temperture Setup (Instlltion) Shortut keys 11 Siewll vents see Vent oors Simultion see Test moe Spee (ommunition) 58 Stti pressure (SP) Current pressure level 54 Groups of SP settings See Vent oors or Tunnel Curtin Mesuring units 13 Pressure lrms 52 Low lrm urve 16, 52 CC24-7 ELITE rev.23 71

72 SP Proe Ativtion 15 Clirtion 17 Stti pressure simultion 21 Tuing instlltion 8 Vent oors see Vent oors Stir fns Ativtion 15 Priniple of opertion 18 Rely seletion 18 Summer see Sesons T Tehnil speifitions 57 Temperture Averge room temperture Current verge T 54 Proe ssignment 17 T History 54 Critil temperture 51 Outsie temperture Ativtion (Out T proe) 15 Current reing 54 History 54 Outsie influene on T lrms 51 Out. T Influene on SP groups 36 Proes Proe ssignment 17 Set points Current set point 54 Curve 14, 22 Night set point 14, 22 Opertion & settings 22 Temperture lrms Priniple of opertion 51 Settings 51 Temperture urve see Curves Temperture simultion 21 Temperture units 13 Test moe 21 Time Setting the time n te 12 Time formt 13 Timer-se relys see Relys Timer see Clok outputs Tuing instlltion (Stti pressure) 8 Tunnel urtin (pressure-se) Ativtion 15 Multiple tunnel stge with ge Ativtion 15 Priniple of opertion 29 Open tunnel on lrm 52 Pre-opening Ativtion (norml or tunnel help) 15 Pre-opening ely 15 Priniple of opertion 29 Rely ssignment 19 Settings 30 Stti pressure (2n group settings) Ativtion 16 Settings 30 Trnsition 36 Trnsition from lterl to tunnel 15 Tunnel help 15 Use in nturl ventiltion Ativtion 15 Tunnel urtin (timer-se) Ativtion 15 Multiple tunnel stge with ge Ativtion 15 Priniple of opertion 31 Priniple of opertion 31 Rely ssignment 19 Settings 31 Trnsition from lterl to tunnel 15 U Units 13 User-efine shortut key 11 User psswor 12 V Vrile fns see Fn stges Vent oors (pressure-se) Ativtion 16 Open vents on lrm 52 Pre-opening ely 16 Priniple of opertion 35 Rely ssignment 19 Settings 36 Stti pressure (2n group settings) Ativtion 15 Settings 35 Trnsition 36 Trnsition from lterl to tunnel 15 Vent oors (timer-se) Ativtion 16 Priniple of opertion 37 Rely ssignment 19 Settings 37 Vent oors (with potentiometer) see Inlets Ventiltion see Fn stges or Min. Vent. Version 21 W Wter meter Ativtion 14 Mesuring units 13 Wter onsumption Consumption history 54 Current reing 54 Wter spill lrm 53 Wether see Temperture Win ely 42 Winter see Sesons Wiring 7 Worksheet Instlltion setup 60, 61 Rely ssignment 64 Z Zero-rossing sreen CC24-7 ELITE rev.23

73

74 M rev.23 REV. 15