1500 psi (103 bar) for Metallic Pump Heads 350 psi (24 bar) for Non-metallic Pump Heads

Transcription

1 G1 eries Maximum Flow Rate: Maximum Pressure: 8.8 gpm (33.4 l/min) 15 psi (13 bar) for Metallic Pump eads 35 psi (24 bar) for Non-metallic Pump eads G1 with ast Iron pump head G1 with Brass pump head G1 with Polypropylene pump head G1 with tainless teel pump head and ANI flanges 44

2 G1 eries Performance apacities Flow Max. Max. Flow 1 psi (69 bar) Model rpm gpm l/min G1-X G G G1-I psi (13 bar) G1-X G Performance and specification ratings apply to G1 configurations unless specifically noted otherwise. Maximum Flow at Designated Pressure Pressure Maximum Inlet Pressure 25 psi (17 bar) Maximum Discharge Pressure Metallic Pump eads: G1-X,,, I to 1 psi (69 bar) G1-X to 15 psi (13 79 rpm max. Non-metallic Pump eads: 25 psi (17 bar) Polypropylene 35 psi (24 bar) PVDF G1-X bar (1 psi) 34 bar (5 psi) 69 bar (1 psi) G Gallons Per Minute G Liters Per Minute bar (15 psi) 79 rpm G1-I Revolutions Per Minute 45

3 G1 eries pecifications Flow 69 bar (1 psi) 4-pole 5 z Model rpm gpm l/min G1-X G G G1-I Flow 69 bar (1 psi) 6-pole 5 z Model rpm gpm l/min G1-X G G G1-I bar (15 psi) Model gal/rev liters/rev G1-X G bar (1 psi) Model gal/rev liters/rev G1-X G G G1-I Maximum Discharge Pressure Metallic eads: 69 bar (1 rpm (G1-X) 69 bar (1 rpm (G1-,, I) 13 bar (15 rpm (G1-X) Non-metallic eads: 17 bar (25 psi) Polypropylene 24 bar (35 psi) PVDF Maximum Inlet Pressure 17 bar (25 psi) Maximum Operating emperature Metallic eads: Non-metallic eads: Maximum olids ize Inlet Port Discharge Port haft Diameter haft Rotation Bearings Oil apacity Weight Metallic eads: Non-metallic eads: 121 (25 F) - onsult factory for correct component selection for temperatures from 71 (16 F) to 121 (25 F). 6 (14 F) 5 microns 1 inch BP 1 inch NP 15lb ANI RF flange 3/4 inch BP 3/4 inch NP 6lb ANI RF flange 22.2 mm (7/8 inch) Reverse (bi-directional) apered roller bearings 1.5 liters (1.1 U quarts) - ee pages 96 and 97 for oil selection and specification kg (48 lbs.) 15.9 kg (35 lbs.) alculating Required Power 15 x rpm + gpm x psi = electric motor hp 63, 1,46 When using a variable frequency drive (VFD) calculate the hp or kw at minimum and maximum pump speed to ensure the correct hp or kw motor is selected. Note that motor manufacturers typically de-rate the service factor to 1. when operating with a VFD. Net Positive uction ead (NPr) NPr (feet of water) 15 x rpm + l/min x bar = electric motor kw 84, ee page 164 for calculating pulley size Positive inlet pressure required for: A) All pumps with PF diaphragms elf-priming: Revolutions Per Minute B) Pumps with I-cam (consult factory) ach ydra-ell pump has different lift capability depending on model size, cam angle, speed, and fluid characteristics. o ensure that your specific lift characteristics are met, refer to the inlet calculations regarding friction, and acceleration head losses in your ydra-ell Installation & ervice Manual. ompare those calculations to the NPr curves above. X I NPr (meters of water) 46 For technical assistance in pump selection, see Frequently Asked Questions on page 162, Design onsiderations on page 163, and Installation Guidelines on pages

4 G1 eries Representative Drawings G1 Models with Metallic Pump ead mm (Inches) 3/4 BP OUL Ø184.2 (7.25) Ø22.2 (.87) 4.8 (.19) 57.2 (2.25) 28.6 (1.13) 61.8 (2.44) 18.3 (4.27) (9.42) 19.5 (7.5) 1 BP INL 43.7 (1.72) 52.3 (2.6) 283. (11.14) 76.2 (3.) 11.8 (4.36) 47.3 (1.86) 4X 1.31 X 19.5 (.46 X.75) (6.25) (4.97) G1 Models with Non-metallic Pump ead mm (Inches) Ø184.2 (7.25) 12.7 (.5) 3/4 BP OUL 24.7 (.97) Ø22.2 (.87) 4.8 (.19) 57.2 (2.25) 14.3 (.56) (9.42) 18.3 (4.27) 61.8 (2.44) 19.5 (.75) 1 BP INL 43.7 (1.72) 52.3 (2.6) 76.2 (3.) (5.6) 65.1 (2.56) 12.2 (.48) 4X 1.31 X 19.5 (.46 X.75) (6.25) (4.97) 3.8 (11.84) Note: ontact factory for additional drawings of specific models and configurations. 47

5 51.7 (2.4) G1 eries Adapters/Valves/kids 11.7 (4.) Ø (7.35) Pump/Motor Adapter mm (Inches) Part Number: A Must be ordered separately for G1 models for use with I 8-9 frame motors, B5 flange. NMA adapter available - consult factory. Ø 11 (3.98) MAX OUPLR O.D. Part Number: A Must be ordered separately for G1 models for use with I frame motors, B5 flange. NMA adapter available - consult factory (4.95) 51.7 (2.4) 11.7 (4.) 75.7 (2.98) Ø (7.35) Ø 11 (3.98) MAX OUPLR O.D. Ø (9.65) Ø 18 (4.25) MAX OUPLR O.D. Valve election A seal-less 62 Pressure Regulating Valve is recommended for ydra- ell G1 pumping systems, especially for highpressure requirements or when handling dirty fluids. ee page 88 for more information. A 22 Pressure Regulating Valve provides a capable, lower-cost alternative to 62 valves for ydra-ell G1 pumping systems. ee page 84 for more information. kid-mounted G1 with 3hp, 3-phase motor. 48

6 G1 eries ow to Order Ordering Information A complete G1 eries Model Number contains 12 digits including 9 customer-specified design and materials options, for example: G1XKBFA. Order Digit ode Description 1-3 Pump onfiguration G1 haft-driven (BP Ports or ANI Flanges)* *Pump/motor adapters ordered separately. ee previous page. 4 ydraulic nd am X Max 3.6 l/min ( rpm I Max 25.1 l/min ( rpm Max 18.8 l/min ( rpm Max 12.5 l/min ( rpm 5 Pump ead Version K R X Kel-ell BP Ports Kel-ell Reduced Pocket AX (Note: AX 94/9/ ertified, ategory 2, Zone 1. Includes certificate and oil level monitor.) 6 Pump ead Material B Brass G M N P ast Iron (Nickel-plated) Duplex Alloy 225 (with astelloy followers & follower screws) PVDF (with astelloy followers & follower screws) Polypropylene (with astelloy followers & follower screws) Polypropylene (with 316L tainless teel followers & follower screws) R 316L tainless teel ANI flange class 15 x 6 316L tainless teel astelloy W12MW 7 Diaphragm & O-ring Material A Aflas diaphragm / PF o-ring G J P PDM (requires PDM-compatible oil - Digit 12 oil code ) FKM PF (available with and cams only; 12 rpm max.) Neoprene Buna-N Order Digit ode Description 8 Valve eat Material D eramic ungsten arbide 17-4 tainless teel 316L tainless teel astelloy 9 Valve Material D F eramic ungsten arbide 17-4 tainless teel N Nitronic 5 astelloy 1 Valve prings lgiloy 17-7 tainless teel astelloy 11 Valve pring Retainers M P Y elcon 17-7 tainless teel PVDF Polypropylene astelloy Nylon (Zytel) 12 ydra-oil A B G 1W3 standard-duty oil 4-wt for continuous-duty oil (use with 316L or astelloy W12MW pump head - standard) PDM-compatible oil Food-contact oil 5W3 cold-temp severe-duty synthetic oil 15W5 high-temp severe-duty synthetic oil G1 Pump ousing is standard as ast Aluminum. Upgrade to Ductile Iron available. Note: For motors, bases, couplings and other pump accessories, refer to the Accessories section beginning on page

7 eal-less Pumps World eadquarters & Manufacturing Wanner ngineering, Inc. 124 hestnut Avenue, Minneapolis, MN 5543 UA Phone: Fax: oll-free Fax (UA): mail: Regional Office 27 U ighway 281 Wichita Falls, X 7631 UA Phone: oll-free: mail: sales@wannereng.com Latin American Office R. Álvaro Anes, 15 Bairro ampestre anto André/ão Paulo, Brazil - P 97-3 Phone: +55 (11) mail: mmagoni@wannereng.com Wanner International, Ltd. ampshire - United Kingdom Phone: +44 () mail: sales@wannerint.com Wanner Pumps Ltd. Wanner Pumps, Ltd. Kowloon - ong Kong Phone: mail: sales@wannerpumps.com hanghai - hina Phone: mail: sales@wannerpumps.com Printed in UA Wanner ngineering, Inc. P M-M 8.16 Rev B