User manual and technical specifications Lat Pulley GB File: Lat Pulley 702876, 702965, 704192 Date: 2017-06-27 Manufacturer: Rev.: RM 02 Ring Mekanikk AS Tlf.: +47 62 33 00 00 e-post: ringorder@ringmek.com Date: 2017-06-27 web adr.: www.ringmek.com 1
Introduction : This user manual for your lat-pulley is ment to guide you to the best use of the apparatus, and ensure that the patient safety is taken care of. This user manual is for: 1. RM art. 702876 - lat pulley 50 kg 2. RM art. 702965 - lat pulley 80 kg 3. RM art. 704192 - lat pulley 100 kg Read the user manual carefully before using the apparatus. Content in this manual: Chapter Text Page a) Declaration of conformity 2 b) User manual 3 c) Maintenance 4 d) Precautions 4 e) Limitations 4 f) Adjustment/settings 5 g) Areas of use 5 h) Repairs 5 i) Drawings 6-8 j) Technical specifications 9 k) Additional equipment 9(8) CE labelling is done in accordance with the machine directive 89/392/EEC Date: 2017-06-27 2
A. EC DECLARATION OF CONFORMITY FOR MACHINERY Manufacturer: Ring Mekanikk AS Adress: Industriveien 10, 2390 Moelv, NORWAY Herewith declares that: Apparatus with number 702876, 702965, 704192 is in conformity with the provisions of the Machinery Directive(directive 89/392/EEC), as amended, and with national implementing legislation. Moelv, Norway 2017-06-27 Ole Edvard Bakken Ole Edvard Bakken Development Manager Date: 2017-06-27 3
B. User manual: 1. Installation and unwrapping. Inspect the wrapping carefully when receiving the pulley, and if there are signs of damage, you must contact your forwarder immediately for damage claims. 2. Do NOT remove straps on the pulleys weight stack, before you have placed the equipment where it is supposed to be used. 3. For mounting the pulley to a wall: a. Place the apparatus where it should stand, and remove straps around the weights stack. b. Mark of holes up and down, against wall. see drawing page.6. If concrete wall, drill Ø10 holes for plugs enclosed. c. When attachment to tree/chipboard/plaster, You must find proper attachment for nails, or use other attachment equipment that is ment for this area of use. d. When attachment to module frame, use attachment holes up and down that compares with the holes in the module frame. For this attachment use bolts that are enclosed in this shipment. e. For mounting of gallow on top of the apparatus, it can be mounted in 3 different heights. Attachment of rope and rope shortener see drawing on page 6. C. Maintenance: 1. Check the rope every week for damage, if there are damage it must be replaced. Use only the same rope. 2. Check the carabinhook for damage, it there are damage, it must be replaced. Use only the same type. 3. The gliding tube on the weight stack must be cleaned and smeared with silicone spray. 4. If the apparatus is attached to wall, the wall bearings must be checked regularely to maintain the users safety. 5. Note. when ordering parts, contact the dealer and see for part no. on page 7. Date: 2017-06-27 4
D. Precautions: The pulley is only ment to be used for specific theraputic and training excercises, and with the additional equipment we have described. see page 8 and 9. E. Limitations: 1. One must not push or pull the apparatus using the gliding rods, this can cause damage to the functioning of the gliding of weights. 2. One must not load the apparatus with more weights or kg s than the weights that are attached to the weight stack, this can cause damage on both apparatus and user. 3. Apparatus is ment for indoors use only. 4. Apparatus must not be placed in rooms with haigh humidity or in rooms with connection to swimming pools. This can cause corrotion and/or rust. F. Adjustments/settings: 1. When setting the desired weight, set the weight pin for the right weight on the weight stack, see scale. 2. Too adjust the length of the rope, use the little metal piece that are attached to the rope. Lift this up and pull the rope until you have the desired length. Then release the rope for locking, see drawing on page 6 no.1. G. Area of use: The pulley is ment to be used for training or treatment in different categories. To get the best use of the apparatus, it should be used according to instructions from instructor or therapeut. Date: 2017-06-27 5
H. Repairs: 1. If any problems occur during use, try to correct it using this manual. 2. Note. When replacing parts, use only the original parts that you can order from your dealer. Use the partslist drawing on page 7. 3. If there is still a problem, take contact with your dealer. Remember to take note of the production year, serial no., and art. no., before calling the dealer. Date: 2017-06-27 6
Date: 2017-06-27 7
I. Date: 2017-06-27 8
I. Date: 2017-06-27 9
J. Technical specifications: Max height: 255cm Min height : 235cm Depht : 24cm Width : 35cm Weightstack types: 50 kg RM art. 702876 80 kg RM art. 702965 100 kg RM art. 704192 Type of rope: Roblon Admiral 2000 8mm nylon with kevlar core. Lenght 3,8 m. K. Additional equipment: Item description Item no. 1. 2.5 Kg weight for lat pulley 180119-10 2. Deload device lat pulley-bent 180115-50 3. Deload device lat pulley-streight 180115-60 4. Step stool 180113 5. Handgrip for rowing 180 875-10 6. Device for rowing 180 115-20 7. Device for up-pull 180 115-10 8. Stool for lat pulley 180115-30 9. Rotary triceps rod-streight 180 888-20 10. Triceps rod 35cm-streight 180 888 11. Triceps rod 35cm-bent 180 888-10 For more information on additional equipment, take contact with dealer. If ordering additional equipment, always rember to give up the art.no. you are ordering for, and the production year of your apparatus. Date: 2017-06-27 10