Compressed Air Cleaning Filter Series

Compressed ir Cleaning Filter Series M /FF Series For Water Droplet, Solid/Oil Separation and Deodorization Modular connection, Space-saving design, Labor-saving in piping! Uses the same spacer as the F.R.L. combination C series. Possible to make a modular connection with products such as R series regulator. Options added ddition: 5 types 1. MPa specifications FKM specifications With differential pressure switch (125 VC, 30 VDC) With differential pressure switch (30 VDC) White vaseline specifications Spacer Note) Note) Spacer with bracket cannot be mounted. Use the attached bracket. MG C, FF C, M C, MD C MH C, ME C, MF C Differential pressure switch MH + ME MH + ME + MF Height and weight reduced by up to 40% New MG C, FF C, M C, MD C MH C, ME C, MF C Modular connection example The C type is only suitable for modular connection. Compact, Lightweight (ME C, MF C) Current Water Droplet Separation Water Separator/MG Solid/Oil Separation Main Line Filter/FF Mist Separator/M Micro Mist Separator/MD Micro Mist Separator with Pre-filter/MH Super Mist Separator/ME Deodorization Odor Removal Filter/MF H HW T B G K MG FF M MD MH ME MF D D 3 B

M /FF Series Water droplet separation Water Separator Water droplet removal ratio: % Large dust particle filtration, Oil droplet separation Main Line Filter Nominal filtration rating: 3 µm [Filtration efficiency: %] FF2C to 22C Dust filtration, Oil mist separation Mist Separator MG150C to 550C FF37B/75B Nominal filtration rating: 0.3 µm [Filtration efficiency:.%] Oil mist density at outlet: Max. 1.0 mg/m 3 (NR) [ 0.8 ppm] M150C to 550C Dust filtration, Oil mist separation Micro Mist Separator Nominal filtration rating: 0.01 µm [Filtration efficiency:.%] Oil mist density at outlet: Max. 0.1 mg/m 3 (NR) [ 0.08 ppm] MG50/850 FF75 to 2 M50/850 Model 150C 250C 350C MG 450C 550C 50 850 2C 4C 8C 11C 22C FF 37B 75B 75 125 150 2 150C 250C 350C M 450C 550C 50 850 150C 250C 350C 450C MD 550C 50 850 00 00 Rated flow L/min (NR) 300 750 1,500 2,0 3,700,000 12,000 300 750 1,500 2,0 3,700,000 12,000 12,400 23,700 30,000 45,000 300 750 1,500 2,0 3,700,000 12,000 0 500 1,000 2,000 3,700,000 12,000 24,000 40,000 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 50(2B) flange 80(3B) flange 0(4B) flange 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 50(2B), 80(3B), 0(4B) flange 0(4B), 150(B) flange Note Piping support type Piping support type Free standing type Piping support type Piping support type Free standing type MD150C to 550C MD50, 850 B 4

Compressed ir Cleaning Filter Series M /FF Series Dust filtration, Oil mist separation Micro Mist Separator with Pre-filter Built-in 0.3 µm pre-filter The M + MD element have been integrated to achieve a space-saving design. Nominal filtration rating: 0.01 µm [Filtration efficiency:.%] Oil mist density at outlet: Max. 0.1 mg/m 3 (NR) [ 0.08 ppm] Model 150C 250C 350C MH 450C 550C 50 Rated flow L/min (NR) 0 500 1,000 2,000 3,700,000 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 Note Piping support type H HW T 850 12,000 1 1/2, 2 B 150C 0 1/8, 1/4 Super Mist Separator Odor Removal Filter MH150C to 550C MH50/850 Dust filtration, Oil mist adsorption Color change indicates when element is saturated. Nominal filtration rating: 0.01 µm [Filtration efficiency:.%] Oil mist density at outlet: Max. 0.01 mg/m 3 (NR) [ 0.008 ppm] Cleanliness at outlet: Not more than 0 particles of size 0.3 µm or larger/ft 3 [35 particles or less/ L (NR)] ME150C to 550C ME50/850 Deodorization Nominal filtration rating: 0.01 µm [Filtration efficiency:.%] Oil mist density at outlet: Max. 0.004 mg/m 3 (NR) [ 0.0032 ppm] ME MF 250C 350C 450C 550C 50 850 150C 250C 350C 450C 550C 50 850 500 1,000 2,000 3,700,000 12,000 0 500 1,000 2,000 3,700,000 12,000 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 1, 1 1/2 1 1/2, 2 Piping support type Piping support type G K MG FF M MD MH ME MF D D MF150C to 550C MF50, 850 5 B

Compressed ir Cleaning Filter Series M /FF Series Series Water removal rate Nominal filtration rating Oil mist density at outlet Smell Page Water Droplet Separation Water Separator Eliminates water droplets in the compressed air. MG Series % P.7 Main Line Filter Eliminates impurities such as oil and foreign matter, etc. in compressed air. FF Series 3 µm (Filtration efficiency: %) P.215 Deodorization Solid/Oil Separation Mist Separator Eliminates oil mist in compressed air or rust sized 0.3 µm or more, and foreign matter such as carbon. Micro Mist Separator Eliminates foreign matter sized 0.01 µm or more, or oil particles in an aerosol state. Micro Mist Separator with Pre-filter Incorporates pre-filter (equivalent to the M series) into micro mist separator. Super Mist Separator Captures foreign matter sized 0.01 µm or more and adsorbs oil particles in an aerosol state. Odor Removal Filter Eliminates odor from compressed air. M Series MD Series MH Series ME Series MF Series 0.3 µm (Filtration efficiency:.%) 0.01 µm (Filtration efficiency:.%) 0.01 µm (Filtration efficiency:.%) 0.01 µm (Filtration efficiency:.%) 1 mg/m 3 (NR) ( 0.8 ppm) (after oil saturation) 0.1 mg/m 3 (NR) ( 0.08 ppm) (after oil saturation) 0.01 mg/m 3 (NR) ( 0.008 ppm) 0.004 mg/m 3 (NR) ( 0.0032 ppm) Reduces oil smell. Deodorizes oil smell. P.223 P.231 P.241 P.24 P.257 Operating State and Proper Use of uto P.25 Optional ccessories (Spacer for Modular Connection, Piping dapter) P.2 Bowl ssembly P.28 Options Rubber material: FKM - reversal direction White vaseline For medium air pressure guide 1/4 female threaded With element service indicator With differential pressure switch (with indicator) (125 VC, 30 VDC) Refer to How to Order of respective models. pplicable only to the FF37B, 75B, M 50 and 850 by Made to Order. With differential pressure gauge (X) Manage the replacement period by monitoring the clogged element. With differential pressure switch (with indicator) (X37) The differential pressure used as the guide for the element replacement period, can be checked Made to Order visually and with an electrical signal. With - flange (X15) Flange piping connection With differential pressure gauge, - flange (X17) The replacement period due to clogging of the element can be checked by the differential pressure gauge. Flange piping connection pplicable only to the FF37B, 75B, M 50 and 850. Specific Product Precautions uto drain, drain piping threaded connection type (X2) Threaded connection for the piping of the auto drain exhaust port White vaseline specifications (X12) Using white vaseline for lubricant. Main line filter for high flow rate with nominal filtration rating of 0.3 µm (X13) This filter is for high flows with a nominal filtration rating the same as the M series mist separator. With by-pass port (X30) Ports connected to the and sides are provided in two locations. This specification can be used for applications which do not require flow rates, which leads to reduction in piping labor and saves space. P.272 P.277 uto Valve, Motor Operated uto, Heavy Duty uto, Differential Pressure Gauge P.37

Water Separator MG Series RoHS Can remove water droplets in compressed air. Use this product in cases where water must be avoided, but not so dry as when an air dryer is used. Through the adoption of a dedicated element and the ample housing interior space, a % water removal rate has been achieved. Caution Water separator can remove water droplets, but it cannot remove moisture. Condition of inlet air Pressure: 0.7 MPa Temperature: 25 C Relative humidity: 0% Liquid water content (Water droplet content): 15 g/m 3 (NR) Compressed air flow: Rated flow of each model Water removal rate (%) = Removed water (Water droplet) (g) x 0 Inflowed water (Water droplet) (g) Modular connection is possible with MG150C to 550C. (For details, refer to page 2.) Model Model MG150C MG250C MG350C MG450C MG550C MG50 MG850 Note) Rated flow (L/min (NR)) 300 750 1500 20 3700 000 100 Port size 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 1, 1 1 2 1 1 2, 2 Weight (kg) 0.38 0.55 0. 1.4 2.1 4.2.5 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page 2) and Maximum Flow Capacity Line (page 211). Specifications Fluid Compressed air Max. operating pressure 1.0 MPa Min. operating pressure 0.05 MPa Proof pressure 1.5 MPa mbient and fluid temperature 5 to 0 C Water removal rate % Element replacement period 2 years or when pressure drop reached 0.1 MPa With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) ccessory Part No. pplicable model MG150C MG250C MG350C MG450C MG550C MG50 MG850 Bracket assembly M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 (with 2 mounting screws) Caution Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. H HW T B G K MG FF M MD MH ME MF D D MG150C to 550C MG50/850 ( cock specifications) (uto drain specifications) Made to Order (For details, refer to page 272.) 7

MG Series How to Order MG150C to 550C 01 02 03 04 0 MG 550 C Port Options Size 150 250 350 450 550 size 150 1/8 1/4 3/8 1/2 3/4 1 Thread type Type Nil Rc F G N NPT Port size pplicable size 250 350 450 550 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). Nil F H J R V Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Rubber material: FKM For medium air pressure (1. MPa) guide 1/4 female threaded 5 - reversal direction White vaseline 5 Without a valve function uto drain 2 3 Description Nil Without auto drain (With drain cock 4 ) C N.C. (Normally closed) port is closed when pressure is not applied. D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to page 25 for proper use of the auto drain. (Only one auto drain specification can be selected.) 3 Refer to the following table for the available combinations of the auto drain specifications and options. 4 When the option J is selected, the auto drain and drain cock are not available. uto Specifications/Option Combinations : ll types of auto drain specifications are available. (including drain guide, J specification) : N.C. auto drain ( C specification) is not available. : Both N.C. and N.O. auto drain ( C, D specification) are not available. F H R V Nil F H R V : Not available F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. B 8

Water Separator MG Series MG50/850 MG 50 How to Order Options Size 50 850 14 Thread type Type Nil Rc F G N NPT Port size 1 1 1 2 2 Port size pplicable size 50 850 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 2 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Nil J guide 1 4 female threaded 5 R - reversal direction 5 Without a valve function uto drain 2 Description Nil Without auto drain (With drain cock 3 4 ) D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to the following table for the available combinations of the auto drain specifications and options. 3 When the option J is selected, the auto drain and drain cock are not available. 4 Body size 850 is equipped with a ball valve (Rc 3/8). Mount a piping adapter -P0 (page 27) to the ball valve if NPT 3/8 female threaded is required. uto Specifications/Option Combinations : vailable : Not available uto drain specifications/option uto drain specifications Option pplicable model D J R MG50 MG850 uto drain specifications N.O. auto drain guide 1 4 D J Option - reversal direction R R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) H HW T B G K MG FF M MD MH ME MF D D

MG Series Flow Rate Characteristics (Representative values) / Select the model under the max. flow capacity line. Note) Compressed air over max. flow capacity line in the table below may not meet the specifications of the product. MG150C MG450C MG850 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) MG250C MG550C capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) MG350C capacity line MG50 capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) 2

Water Separator MG Series Construction MG150C to 550C, MG50 Component Parts No. Description Material Note 1 2 3 Replacement Parts No. Description Material 4 Element assembly Resin, others pplicable model Except option F For option F MG150C MG-EL150 MG-EL150-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 280 for replacement of auto drain. Maximum Flow Capacity Line capacity (m 3 /min (NR)) Body q r w Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass e Inner/outer surface coating MG250C MG-EL250 MG-EL250-F MG850 MG350C MG-EL350 MG-EL350-F Note) The figure shows the drain cock specification. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 212 to 214 for details. Model MG450C MG-EL450 MG-EL450-F Model Selection MG550C MG-EL550 MG-EL550-F MG50 MG-EL50 MG850 MG-EL850 Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The MG50 is obtained when the max. flow capacity line is above the intersecting point in the graph. Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. H HW T B G K MG FF M MD MH ME MF D D Inlet pressure (MPa) 211

MG Series Dimensions MG150C to 550C P Q R S uto drain C: With auto drain (N.C.) D: With auto drain (N.O.) uto drain F O Color of drain cock Gray: N.C. Black: N.O. 34 One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 K U T D I L M øv Bracket (ccessory) N Combination of D: With auto drain (N.O.) and H: For medium air pressure uto drain H C J E B 2 Port size Note) 1/4 female threaded The same thread type is used for the and. Note) 23 for MG250C Width across flats 17 Option J: guide 1/4 female threaded G Maintenance space M5 Note) The figure shows the drain cock specification. guide Width across flats 24 1/4 female threaded The same thread type is used for the and. Model MG150C MG250C MG350C MG450C MG550C Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 11 175 7 228 22 B 14 18 24 C 113 145 1 0 D 3 7 0 122 E 23 23 23 23 23 F 3 7 0 122 G 15 H 17 13 225 24 281 I 5 J 24 80 28 0 31 0 33 K 5 8 8 T 7 Bracket related dimensions U L M V N 12 35 7 12 14 18 18 7 40 12 50 15 55 15 5 O 54 80 88 2 P 70 Q 2 80 28 5 34 111 50 12 0 R 4.5 5 5 (mm) S 1. 2 2.3 3.2 3.2 212

Water Separator MG Series Dimensions MG50 uto drain D: With auto drain (N.O.) 10 13 12 180 7 4.5 uto drain cock: Black 34 H HW T One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 B 10 Option J: guide 1/4 female threaded 15 11 150 Bracket (ccessory) 85 G K 40 32 guide MG 337 253 314 2 x Port size 1, 1 1 /2 female threaded Width across flats 24 1/4 female threaded The same thread type is used for the and. FF M MD MH ME MF 23 Maintenance space M5 D Note) The figure shows the drain cock specification. D 213

MG Series Dimensions MG850 uto drain D: With auto drain (N.O.) 2 1 2 184 180 24 () 15 13 18 uto drain 3/8 female threaded The same thread type is used for the and. 23 2 180 1 Bracket ccessory 348 Drawing of view B 58 44 3 42 View B 30 2 x Port size 11/2, 2 female threaded 41 Maintenance space Rc 3/8 Note) The figure shows the drain cock specification. 214

Main Line Filter FF Series RoHS Can remove impurities such as oil, water and foreign matter in compressed air and can improve the function of a dryer in the downstream, extend the replacement period of precision filter element, and prevent trouble with the equipment. Modular connection is possible with FF2C to 22C. (For details, refer to page 2.) FF2C to 22C FF37B, 75B ( cock specifications) (uto drain specifications) Made to Order (For details, refer to page 272.) Caution Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. Model Model FF2C FF4C FF8C FF11C FF22C FF37B FF75B FF75 FF125 FF150 FF2 Rated flow Note) 300 750 1500 20 3700 000 100 12400 23700 30000 45000 (L/min (NR)) Port size 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 50(2B) 80(3B) 0(4B) 0(4B) 4 3 4, 1 1, 1 1 2 1 1 2, 2 JIS K FF flange Weight (kg) 0.38 0.55 0. 1.4 2.1 4.2.5 50 52 72 87 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page 218) and Maximum Flow Capacity Line below. Specifications Fluid Max. operating pressure Min. operating pressure Note 2) Proof pressure mbient and fluid temperature Filtration rating Element replacement period ccessory Part No./For FF2C to 22C, FF37B/75B pplicable model FF2C FF4C FF8C FF11C FF22C FF37B FF75B Bracket assembly (with 2 mounting screws) M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 ccessory Part No./For FF75 to 2 pplicable model FF75 FF125 FF150 FF2 uto drain with metal case (2 pcs. each) uto drain with resin case (2 pcs. each) Pressure gauge (2 pcs. each) D402-03-2 D402-03 G4-15-02 Companion flange (2 pcs. each) 50(2B)JIS K FF flange 80(3B)JIS K FF flange 0(4B)JIS K FF flange nchor bolt (3 pcs. each) I-2S Model Selection Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The FF37B is obtained when the max. flow capacity line is above the intersecting point in the graph. Compressed air 1.0 MPa Note 1) 0.05 MPa 1.5 MPa 5 to 0 C 3 µm (Filtration efficiency: %) 2 years Note 1) or when pressure drop reached 0.1 MPa Note 1) The maximum operating pressure of the FF75 to FF2 is 0.7 MPa, and the element replacement period is when the pressure drop reaches 0.1 MPa or after 1 year operation. Note 2) With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Maximum Flow Capacity Line capacity (m 3 /min (NR)) Inlet pressure (MPa) H HW T B G K MG FF M MD MH ME MF D D 215

FF Series FF2C to 22C 01 02 03 04 0 Options Port size 2 1/8 1/4 3/8 1/2 3/4 1 Thread type Type Nil Rc F G N NPT Port size pplicable size 4 8 11 22 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). uto Specifications/Option Combinations Nil F H R S U T V Nil Note F FF 22 C Size 2 4 8 11 22 : ll types of auto drain specifications are available. (including drain guide, J specification) : N.C. auto drain ( C specification) is not available. : Both N.C. and N.O. auto drain ( C, D specification) are not available. H R Note S U T V Note Note Note: Only one drain exhaust method can be selected. : Not available How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table on the lower left for the available combinations. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) J guide 1/4 female threaded 5 R - reversal direction S With differential pressure switch (125 VC, 30 VDC), Note) U With differential pressure switch (30 VDC) T With element service indicator V White vaseline 5 Without a valve function Differential pressure switch is included, (but not assembled). Note) Select U if conformity to the EU directive is required. uto drain 2 3 Description Nil Without auto drain (With drain cock 4 ) C N.C. (Normally closed) port is closed when pressure is not applied. D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to page 25 for proper use of the auto drain. (Only one auto drain specification can be selected.) 3 Refer to the table on the left for the available combinations of the auto drain specifications and options. 4 When the option J is selected, the auto drain and drain cock are not available. F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female thread B R: - reversal direction Flow direction: Right to left ir flow is changed to right to left. (Flow direction of the standard: Left to right) T: With element service indicator Pressure drop 0.1 MPa Clogging of the element can be observed visually. V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. 21 S: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from U. Max. contact capacity: V C, W DC Rated contact voltage (max. operating current): 125 V C (0.08 ), 30 V DC (0.33 ) Reed switch U: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from S. Max. contact capacity: W DC Rated contact voltage (max. operating current): 30 V DC (0.33 ) Reed switch

Main Line Filter FF Series FF37B, FF37B/75B75B 14 FF75 to 2 30 40 FF 37 B Size 37 75 Thread type Type Nil Rc F G N NPT Port size 1 1 1 2 2 Port size pplicable size 37 75 How to Order Option 2 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Nil J guide 1 4 female threaded 5 R - reversal direction T With element service indicator 5 Without a valve function uto drain 2 Description Nil Without auto drain (With drain cock 3 ) D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to the following table for the available combinations of the auto drain specifications and options. 3 When the option J is selected, the auto drain and drain cock are not available. 4 Body size 75B is equipped with a ball valve (Rc 3/8). Mount a piping adapter -P0 (page 27) to the ball valve if NPT 3/8 female threaded is required. uto Specifications/Option Combinations : vailable : Not available uto drain specifications/option uto drain specifications Option pplicable model D J R T FF37B FF75B uto drain specifications Option N.O. auto drain guide 1 4 - reversal direction D J R With element service indicator T Port size 50(2B) JIS K FF flange 80(3B) JIS K FF flange 0(4B) JIS K FF flange ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). FF 75 Size 75 125 150 2 Port size pplicable size 75 125 150 2 uto drain (ccessory) Description Nil Without auto drain D With metal case (2 pcs. each) P With resin case (2 pcs. each) Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. nchor bolt (ccessory) Description Nil Without anchor bolt L nchor bolt (3 pcs. each) Companion flange (ccessory) Description Nil Without companion flange F Companion flange (2 pcs. each) Pressure gauge (ccessory) Description Nil Without pressure gauge G Pressure gauge (2 pcs. each) 217 H HW T B G K MG FF M MD MH ME MF D D

FF Series Flow Rate Characteristics (Representative values)/select the model under the max. flow capacity line. (Element oil saturation) Note) Compressed air over max. flow capacity line in the table below may not meet the specifications of the product. FF2C FF22C FF75 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) FF4C FF37B FF125 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) FF8C FF75B FF150 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) FF11C FF2 capacity line capacity line 218 ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR))

Main Line Filter FF Series Construction FF2C to 22C, FF37B FF75B q Replacement Parts No. Description Material 4 r w Element assembly Cotton paper, others Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 280 for replacement of auto drain. FF75 to 2 ( side) Gauge port pplicable model Except option F For option F FF2C FF-EL2B FF-EL2B-F Component Parts No. Description Material Note 1 2 3 Body Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass e Inner/outer surface coating FF4C FF-EL4B FF-EL4B-F FF8C FF-EL8B FF-EL8B-F Note) The figure shows the drain cock specification. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Please refer to pages 2 through to 222 for details. Model FF11C FF-EL11B FF-EL11B-F FF22C FF-EL22B FF-EL22B-F FF37B FF-EL37B FF75B FF-EL75B H HW T B G K MG FF M MD MH ME MF D D Gauge port ( side) Component Parts No. Description 1 Case 2 Cover Material Carbon steel Carbon steel Note Replacement Parts No. Description Material Qty. 3 Element 4 Seal NBR 1 1 Model FF75 FF125 FF150 FF2 EC700-003N EC800-003N EC00-003N L-33S L-34S L-35S 21

FF Series Dimensions FF2C to 22C P Q uto drain C: With auto drain (N.C.) D: With auto drain (N.O.) uto drain F O 2 x port size S, U: With differential pressure switch (with indicator) Y Z T: With element service indicator W X R S Color of drain cock Gray: N.C. Black: N.O. One-touch fitting Thread type Rc, G: ø Thread type NP: ø3/8 Combination of D: With auto drain (N.O.) and H: For medium air pressure 34 J K U T D I L M øv Bracket (ccessory) N uto drain Note) 23 for FF4C Note) Width across flats 17 1/4 female threaded The same thread type is used for the and. H C E B Option J: guide 1/4 female threaded guide Width across flats 24 1/4 female threaded The same thread type is used for the and. G Maintenance space M5 Note) The figure shows the drain cock specification. Model FF2C FF4C FF8C FF11C FF22C 2 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 11 175 7 228 22 B 14 18 24 C 113 145 1 0 D 3 7 0 122 E 23 23 23 23 23 F 3 7 0 122 G Bracket related dimensions 15 H 17 13 225 24 281 I 5 80 0 0 J 24 28 31 33 K 5 8 8 T 7 U 7 L 12 12 14 18 18 M 7 V 12 15 15 N 35 40 50 55 5 O 54 P 70 Q 2 R 4.5 S 1. (mm) Element Differential service pressure indicator related switch related dimensions dimensions W 24 X 37 Y 32 Z 41 80 88 2 80 5 111 12 28 34 50 0 5 5 2 2.3 3.2 3.2 27 32 37 3 37 37 37 37 3 42 43 51 41 41 41 41

Main Line Filter FF Series Dimensions FF37B uto drain D: With auto drain (N.O.) 180 7 uto drain H HW 12 cock: Black T 10 13 4.5 One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 34 Option B J: guide 1/4 female threaded 10 15 11 150 Bracket (ccessory) 85 guide G K 40 32 Width across flats 24 1/4 female threaded The same thread type is used for the and. T: With element service indicator MG FF M 337 253 314 2 x port size 1, 1 1 /2 female threaded 55 37 MD MH ME MF 23 Maintenance space M5 D Note) The figure shows the drain cock specification. D 221

FF Series Dimensions FF75B 18 2 1 3 2 184 2 180 1 Bracket ccessory 15 180 24 () 13 42 View B 30 348 2 x port size 1 /2, 2 female threaded Drawing of view B 44 uto drain D: With auto drain (N.O.) 58 41 uto drain Rc 3/8 23 Maintenance space Note) The figure shows the drain cock specification. 3/8 female threaded The same thread type is used for the and. FF75 to 2 3 x ø holes For foundation bolt Option T: With element service indicator Label N5: Pressure outlet ( side) N: Pressure outlet ( side) ORIENTTION 222 (mm) Model Port size (Flange) ø B C D E F G FF75 FF125 FF150 50(2B)JISK FF flange 80(3B)JISK FF flange 0(4B)JISK FF flange 0 (8B) 0 (8B) 250 (B) 380 380 450 1125 1125 1178 35 35 80 505 505 540 25 25 25 184 184 23 FF2 0(4B)JISK FF flange 300 (12B) 500 121 70 70 325 288

Mist Separator M Series RoHS Can remove oil mist in compressed air and separate and remove particles such as rust or carbon of more than 0.3 µm. Modular connection is possible with M150C to 550C. (For details, refer to page 2.) M150C to 550C ( cock specifications) M50/850 (uto drain specifications) Made to Order (For details, refer to page 272.) Model Model Note) Rated flow (L/min (NR)) Port size Weight (kg) M150C 300 M250C 750 M350C 1500 M450C 20 M550C 3700 M50 000 M850 100 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 1, 1 1 2 1 1 2, 2 0.38 0.55 0. 1.4 2.1 4.2.5 Note) Maximum flow capacity at 0.7 MPa. Maximum flow capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page 22) and Max. Flow Capacity Line (page 227) below. Note) Refer to Made to Order (page 27) for high flow type of M850 or more. Specifications Fluid Max. operating pressure Min. operating pressure 1 Proof pressure mbient and fluid temperature Nominal filtration rating Oil mist density at outlet Element replacement period 1 With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) 2 When the inlet oil mist density is 30 mg/m 3 (NR). ccessory Part No. pplicable model Bracket assembly (with 2 mounting screws) Caution Compressed air 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.3 µm (Filtration efficiency:.%) Max. 1 mg/m 3 (NR) ( 0.8 ppm) 2 2 years or when pressure drop reached 0.1 MPa M150C M250C M350C M450C M550C M50 M850 M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. H HW T B G K MG FF M MD MH ME MF D D 223

M Series M150C to 550C 01 02 03 04 0 uto Specifications/Option Combinations : ll types of auto drain specifications are available. (including drain guide, J specification) : N.C. auto drain ( C specification) is not available. : Both N.C. and N.O. auto drain ( C, D specification) are not available. Nil F H R S U T V Nil Note F H R Note S U T V Note Note Note: Only one drain exhaust method can be selected. : Not available Options M 550 C Size 150 250 350 450 550 Thread type Type Nil Rc F G N NPT Port size Port pplicable size size 150 250 350 450 550 1/8 1/4 3/8 1/2 3/4 1 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table on the lower left for the available combinations. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) J guide 1/4 female threaded 5 R - reversal direction S With differential pressure switch (125 VC, 30 VDC), Note) U With differential pressure switch (30 VDC) T Element service indicator V White vaseline 5 Without a valve function Differential pressure switch is included, (but not assembled). Note) Select U if conformity to the EU directive is required. uto drain 2 3 Description Nil Without auto drain (With drain cock 4 ) C N.C. (Normally closed) port is closed when pressure is not applied. D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to page 25 for proper use of the auto drain. (Only one auto drain specification can be selected.) 3 Refer to the table on the left for the available combinations of the auto drain specifications and options. 4 When the option J is selected, the auto drain and drain cock are not available. F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded B R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) T: With element service indicator Pressure drop 0.1 MPa Clogging of the element can be observed visually. V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. 224 S: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from U. Max. contact capacity: V C, W DC Rated contact voltage (max. operating current): 125 VC (0.08 ), 30 VDC (0.33 ) Reed switch U: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from S. Max. contact capacity: W DC Rated contact voltage (max. operating current): 30 VDC (0.33 ) Reed switch

Mist Separator M Series M50/850 Options M 50 Size 50 850 Port size 14 1 1 1 2 2 Thread type Type Nil Rc F G N NPT Port size pplicable size 50 850 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). How to Order Option 3 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Nil J guide 1 4 female threaded 5 R - reversal direction T With element service indicator 5 Without a valve function uto Specifications/Option Combinations uto drain specifications/option uto drain specifications N.O. auto drain guide 1 4 Option - reversal direction With element service indicator T J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded uto drain 2 Description Nil Without auto drain (With drain cock 3 4 ) D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to the following table for the available combinations of the auto drain specifications and options. 3 When the option J is selected, the auto drain and drain cock are not available. 4 Body size 850 is equipped with a ball valve (Rc 3/8). Mount a piping adapter -P0 (page 27) to the ball valve if NPT 3/8 female threaded is required. D J R R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. uto drain specifications Option D J R T : vailable : Not available pplicable model M50 M850 T: With element service indicator Pressure drop 0.1 MPa Clogging of the element can be observed visually. H HW T B G K MG FF M MD MH ME MF D D 225

M Series Flow Rate Characteristics (Representative values) /Select the model under the max. flow capacity line. (Element oil saturation) Note) Compressed air over max. flow capacity line in the table below may not meet the specifications of the product. M150C M450C M850 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) M250C M550C capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) M350C M50 capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) 22

Mist Separator M Series Construction M150C to 550C, M50 M850 q Component Parts No. Description Material Note 1 2 3 Body Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass Replacement Parts No. Description Material 4 Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 280 for replacement of auto drain. Maximum Flow Capacity Line Maximum flow capacity (m 3 /min (NR)) r w Element assembly Glass fiber, others pplicable model Except option F For option F M150C M-EL150 M-EL150-F e Inner/outer surface coating M250C M-EL250 M-EL250-F M350C M-EL350 M-EL350-F Note) The figure shows the drain cock specification. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 228 through to 230 for details. Model M450C M-EL450 M-EL450-F Model Selection M550C M-EL550 M-EL550-F M50 M-EL50 M850 M-EL850 Select a model in accordance with the following procedure taking the inlet pressure and the maximum flow capacity into consideration. (Example) Inlet pressure: 0. MPa Maximum flow capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and Maximum flow capacity in the graph. 2. The M50 is obtained when the max. flow capacity line is above the intersecting point in the graph. Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. H HW T B G K MG FF M MD MH ME MF D D Inlet pressure (MPa) 227

Z M Series Dimensions M150C to 550C P Q uto drain C: With auto drain (N.C.) D: With auto drain (N.O.) uto drain F R O S Color of drain cock Gray: N.C. Black: N.O. One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 Combination of D: With auto drain (N.O.) and H: For medium air pressure 34 uto drain H C K J U G Maintenance space T D I L M øv Bracket (ccessory) Width across flats 24 1/4 female threaded The same thread type is used for the and. S, U: With differential pressure switch (with indicator) Y T: With element service indicator W X E B M5 Note) The figure shows the drain cock specification. N 2 x Port size Note) 1/4 female threaded The same thread type is used for the and. Note) 23 for M250C Option J: guide 1/4 female threaded guide Width across flats 17 Model M150C M250C M350C M450C M550C 228 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 158 172 4 225 25 B 14 18 24 C 113 145 1 0 D 3 7 0 122 E F 3 7 0 122 G Bracket related dimensions 15 H 173 10 222 24 278 I 5 80 0 0 J 24 28 31 33 K 5 8 8 T 7 U 7 L 12 12 14 18 18 M 7 V 12 15 15 N 35 40 50 55 5 O 54 P 70 Q 2 R 4.5 S 1. (mm) Element Differential service pressure indicator related switch related dimensions dimensions W 24 X 37 Y 32 Z 41 80 88 2 80 5 111 12 28 34 50 0 5 5 2 2.3 3.2 3.2 27 32 37 3 37 37 37 37 3 42 43 51 41 41 41 41

Mist Separator M Series Dimensions M50 uto drain D: With auto drain (N.O.) 12 180 7 uto drain cock: Black H HW T 10 13 4.5 One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 34 Option B J: guide 1/4 female threaded 10 337 253 15 40 11 150 Bracket (ccessory) 314 32 85 2 x Port size 1, 1 1 /2 female threaded guide Width across flats 24 T: With element service indicator 55 1/4 female threaded The same thread type is used for the and. 37 G K MG FF M MD MH ME MF 23 Maintenance space M5 D Note) The figure shows the drain cock specification. D 22

M Series Dimensions M850 2 1 2 184 18 2 180 1 Bracket (ccessory) 180 () 24 3 42 30 15 View B 15 13 348 2 x port size 1 /2, 2 female threaded Drawing of view B 44 uto drain D: With auto drain (N.O.) 58 23 41 uto drain Maintenance space Rc 3/8 Note) The figure shows the drain cock specification. 3/8 female threaded The same thread type is used for the and. Option T: With element service indicator 230

Micro Mist Separator MD Series RoHS Can separate and remove aerosol state oil mist in compressed air and remove particles such as carbon or dust of more than 0.01 µm. Use this product as a pre-filter for compressed air for precision instruments or clean room requiring higher clean air. Modular connection is possible with MD150C to 550C. (For details, refer to page 2.) MD150C to 550C ( cock specifications) MD50/850 (uto drain specifications) Made to Order (For details, refer to page 272.) Model Note) Rated flow (L/min (NR)) Port size Model Weight (kg) MD150C MD250C MD350C MD450C MD550C MD50 MD850 0 500 00 00 3700 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 000 100 0.38 0.55 0. 1.4 2.1 4.2.5 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page 234) and Maximum Flow Capacity Line (page 233). Model/Free Standing Type Model Rated flow (L/min (NR)) Port size Weight (kg) Specifications Fluid Max. operating pressure Note 1) Min. operating pressure Proof pressure mbient and fluid temperature Filtration rating Oil mist density at outlet Element replacement period MD00 24000 50(2B), 80(3B), 0(4B)JIS K FF flange 2 Note 1) With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) Note 2) When the inlet oil mist density is 30 mg/m 3 (NR). Note 3) 0.7 MPa for free standing type ccessory Part No. pplicable model Bracket assembly (with 2 mounting screws) Caution 1, 1 1 2 1 1 2, 2 MD00 40000 0(4B), 150(B)JIS K FF flange 430 Compressed air Note 3) 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.01 µm (Filtration efficiency:.%) Max. 0.1 mg/m 3 (NR) Note 2) (Before saturated with oil, less than 0.01 mg/m 3 (NR) 0.008 ppm) 2 years (1 year for free standing type) or when pressure drop reached 0.1 MPa MD150C MD250C MD350C MD450C MD550C MD50 MD850 M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. H HW T B G K MG FF M MD MH ME MF D D 231

MD Series MD150C to 550C 01 02 03 04 0 Size 150 250 350 450 550 Options Thread type Type Nil Rc F G N NPT Port size Port pplicable size size 150 250 350 450 550 1/8 1/4 3/8 1/2 3/4 1 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). uto Specifications/Option Combinations Nil F H R S U T V Nil Note MD 550 C : ll types of auto drain specifications are available. (including drain guide, J specification) : N.C. auto drain ( C specification) is not available. : Both N.C. and N.O. auto drain ( C, D specification) are not available. F H R Note S U T V Note Note Note: Only one drain exhaust method can be selected. : Not available How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table on the lower left for the available combinations. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) J guide 1/4 female thread 5 R - reversal direction S With differential pressure switch (125 VC, 30 VDC) U With differential pressure switch (30 VDC) T With element service indicator V White vaseline 5 Without a valve function Differential pressure switch is included, (but not assembled). Note) Select U if conformity to the EU directive is required., Note) uto drain 2 3 Description Nil Without auto drain (With drain cock 4 ) C N.C. (Normally closed) port is closed when pressure is not applied. D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to page 25 for proper use of the auto drain. (Only one auto drain specification can be selected.) 3 Refer to the table on the left for the available combinations of the auto drain specifications and options. 4 When the option J is selected, the auto drain and drain cock are not available. F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded B R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) T: With element service indicator Pressure drop 0.1 MPa Clogging of the element can be observed visually. V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. 232 S: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from U. Max. contact capacity: V C, W DC Rated contact voltage (max. operating current): 125 V C (0.08 ), 30 V DC (0.33 ) Reed switch U: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from S. Max. contact capacity: W DC Rated contact voltage (max. operating current): 30 V DC (0.33 ) Reed switch

Micro Mist Separator MD Series MD50/850 14 Nil D MD 50 Size 50 850 Port size 1 1 1 2 2 Thread type Type Nil Rc F G N NPT Port size pplicable size 50 850 Free standing type MD Size Model Selection 00 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). uto drain 2 Description Without auto drain (With drain cock 3 4 ) N.O. (Normally open) port is open when pressure is not applied. 2 Refer to the table on the right for the available combinations of the auto drain specifications and options. 3 When the option J is selected, the auto drain and drain cock are not available. 4 Body size 850 is equipped with a ball valve (Rc 3/8). Mount a piping adapter -P0 (page 27) to the ball valve if NPT 3/8 female threaded is required. MD, uto drain Description 00 With manual drain cock With auto drain uto drain is N.O. (Normally open). port is open when pressure is not applied. Port size 30 40 0 Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The MD50 is obtained when the max. flow capacity line is above the intersecting point in the graph. Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Nil J guide 1 4 female threaded 5 R - reversal direction T With element service indicator 5 Without a valve function uto Specifications/ Option Combinations : vailable : Not available uto drain uto drain specifications/option specifications Option pplicable model D J R T MD50 MD850 uto drain specifications N.O. auto drain guide 1 4 D J Option - reversal direction R With element service indicator T Port size 50(2B)JIS K FF flange 80(3B)JIS K FF flange 0(4B)JIS K FF flange 150(B)JIS K FF flange pplicable size MD 0 MD 0 Maximum Flow Capacity Line capacity (m 3 /min (NR)) MD MD MD850 MD50 MD550C MD450C MD350C MD250C H HW T B G K MG FF M MD MH ME MF D D MD150C Inlet pressure (MPa) 233

MD Series Flow Rate Characteristics (Representative values)/select the model under the max. flow capacity line. ( Element oil saturation Initial condition) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. MD150C MD250C MD350C capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) MD450C MD550C MD50 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) MD850 MD MD capacity line capacity line capacity line ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) ir flow rate (m 3 /min (NR)) 234

Micro Mist Separator MD Series Construction MD150C to 550C, MD50 q MD850 Replacement Parts No. Description Material 4 r w Element assembly Glass fiber, others MD, 0 pplicable model Except option F For option F MD150C MD-EL150 MD-EL150-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 280 for replacement of auto drain. Component Parts No. Description Material Note 1 2 3 Body Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass Inner/outer surface coating e Details of element mounting part MD250C MD-EL250 MD-EL250-F MD350C MD-EL350 MD-EL350-F Component Parts/Material No. 1 Case 2 Cover Description Replacement Parts No. Description 3 Element 4 Seal 5 Seal Model MD450C MD-EL450 MD-EL450-F MD550C MD-EL550 MD-EL550-F Material NBR NBR Note) The figure shows the drain cock specification. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 23 through to 23 for details. MD50 MD-EL50 Model MD, Carbon steel Carbon steel Model MD MD 3174 3 pcs. 3174 5 pcs. 3148 3 pcs. 3148 5 pcs. O.D112 x I.D0 x T3 3 pcs. MD850 MD-EL850 O.D112 x I.D0 x T3 5 pcs. H HW T B G K MG FF M MD MH ME MF D D Gasket V#500 L-3S L-31S 7 O-ring NBR K0001 3 pcs. K0001 5 pcs. 235

Z MD Series Dimensions MD150C to 550C P Q uto drain C: With auto drain (N.C.) D: With auto drain (N.O.) uto drain F R O S Color of drain cock Gray: N.C. Black: N.O. One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 Combination of D: With auto drain (N.O.) and H: For medium air pressure 34 H C K J U G Maintenance space T D I L M øv Bracket (ccessory) 1/4 female threaded The same thread type is used for the and. S, U: With differential pressure switch (with indicator) Y T: With element service indicator W X E B M5 Note) The figure shows the drain cock specification. N 2 x port size uto drain Note) 1/4 female threaded The same thread type is used for the and. Note) 23 for MD250C Option J: guide 1/4 female threaded guide Width across flats 24 Width across flats 17 Model MD150C MD250C MD350C MD450C MD550C 23 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 11 175 7 228 22 B 14 18 24 C 113 145 1 0 D 3 7 0 122 E 23 23 23 23 23 F 3 7 0 122 G Bracket related dimensions 15 H 17 13 225 24 281 I 5 80 0 0 J 24 28 31 33 K 5 8 8 T 7 U 7 L 12 12 14 18 18 M 7 V 12 15 15 N 35 40 50 55 5 O 54 P 70 Q 2 R 4.5 S 1. (mm) Element Differential service pressure indicator related switch related dimensions dimensions W 24 X 37 Y 32 Z 41 80 88 2 80 5 111 12 28 34 50 0 5 5 2 2.3 3.2 3.2 27 32 37 3 37 37 37 37 3 42 43 51 41 41 41 41

Micro Mist Separator MD Series Dimensions MD50 337 10 253 12 13 15 40 Maintenance space 11 180 7 10 150 4.5 Bracket (ccessory) 314 32 23 M5 Note) The figure shows the drain cock specification. 85 2 x port size 1, 11/2 female threaded uto drain D: With auto drain (N.O.) uto drain cock: Black One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 Option J: guide 1/4 female threaded guide Width across flats 24 T: With element service indicator 55 37 34 1/4 female threaded The same thread type is used for the and. H HW T B G K MG FF M MD MH ME MF D D 237

MD Series Dimensions MD850 2 1 18 180 24 () 15 13 2 184 2 180 1 Bracket ccessory 42 3 View B 30 348 2 x port size 11/2, 2 female threaded Drawing of view B 44 41 uto drain D: With auto drain (N.O.) 58 uto drain Rc 3/8 23 Maintenance space 3/8 female threaded The same thread type is used for the and. Note) The figure shows the drain cock specification. Option T: With element service indicator 238

Micro Mist Separator MD Series Dimensions MD, H HW ORIENTTION T 3 x øh holes Label B G Model MD MD Port size (Flange) 50(2B), 80(3B), 0(4B)JIS K FF flange 7 0(4B), 150(B)JIS K FF flange 870 øb 50 745 øc 400 550 D 300 300 E 13 1380 F 1480 1 G 1585 1740 (mm) H 24 24 K MG FF M MD MH ME MF D D 23

Micro Mist Separator with Pre-filter MH Series RoHS Can separate and remove aerosol state oil mist in compressed air and remove particles such as carbon or dust of more than 0.01 µm. Use this product as a pre-filter for compressed air for precision instruments or clean room requiring higher clean air. The M series and MD series have been integrated to achieve a reduction in installation space and in piping labor. Modular connection is possible with MH150C to 550C. (For details, refer to page 2.) MH150C to 550C ( cock specifications) MH50/850 (uto drain specifications) Made to Order (For details, refer to page 272.) Model Model MH150C MH250C MH350C MH450C MH550C MH50 MH850 Note) Rated flow (L/min (NR)) 0 500 00 00 3700 000 100 Port size Weight (kg) 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 0.38 0.55 0. 1.4 2.1 4.2.5 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page 244) and Maximum Flow Capacity Line below. Specifications Fluid Max. operating pressure Min. operating pressure 1 Proof pressure mbient and fluid temperature Nominal filtration density Oil mist density at outlet Element replacement period 1 With auto drain: 0.1 MPa (N.O. type) or 0.15 MPa (N.C. type) 2 When the inlet oil mist density is 30 mg/m 3 (NR). ccessory Part No. pplicable model Bracket assembly (with 2 mounting screws) Model Selection Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The MH50 is obtained when the max. flow capacity line is above the intersecting point in the graph. Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Caution Compressed air 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.01 µm (Filtration efficiency:.%) Max. 0.1 mg/m 3 (NR) 2 (Before saturated with oil, less than 0.01 mg/m 3 (NR) 0.008 ppm) 2 years or when pressure drop reached 0.1 MPa MH150C MH250C MH350C MH450C MH550C MH50 MH850 M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 Maximum Flow Capacity Line capacity (m 3 /min (NR)) Inlet pressure (MPa) 1, 1 1 2 1 1 2, 2 H HW T B G K MG FF M MD MH ME MF D D Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. 241

MH Series MH150C to 550C 01 02 03 04 0 Options Size 150 250 350 450 550 Thread type Type Nil Rc F G N NPT Port size Port pplicable size size 150 250 350 450 550 1/8 1/4 3/8 1/2 3/4 1 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). Exhaust Specifications/Option Combinations Nil F H R S U T V Nil Note MH 550 C : ll types of drain exhaust specifications are available. (including drain guide, J specification) : N.C. auto drain ( C specification) is not available. : Both N.C. and N.O. auto drain ( C, D specification) are not available. F H R Note S U T V Note Note Note: Only one drain exhaust method can be selected. : Not available How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table on the lower left for the available combinations. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) J guide 1/4 female threaded 5 R - reversal direction S With differential pressure switch (125 VC, 30 VDC) U With differential pressure switch (30 VDC) T With element service indicator V White vaseline 5 Without a valve function Differential pressure switch is included, (but not assembled). Note) Select U if conformity to the EU directive is required., Note) uto drain 2 3 Description Nil Without auto drain (With drain cock 4 ) C N.C. (Normally closed) port is closed when pressure is not applied. D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to page 25 for proper use of the auto drain. (Only one auto drain specification can be selected.) 3 Refer to the table on the left for the available combinations of the auto drain specifications and options. 4 When the option J is selected, the auto drain and drain cock are not available. F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. J: guide 1/4 female threaded Pipe threaded connection for the drain exhaust port 1/4 female threaded B R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) T: With element service indicator Pressure drop 0.1 MPa Clogging of the element can be observed visually. V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. 242 S: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from U. Max. contact capacity: V C, W DC Rated contact voltage (max. operating current): 125 V C (0.08 ), 30 V DC (0.33 ) Reed switch U: With differential pressure switch (with indicator) Clogging of the element can be observed visually or with an electrical signal. The rated contact voltage is different from S. Max. contact capacity: W DC Rated contact voltage (max. operating current): 30 V DC (0.33 ) Reed switch

Micro Mist Separator with Pre-filter MH Series MH50/850 MH 50 14 Size 50 850 Thread type Type Nil Rc F G N NPT Port size 1 1 1 2 2 Port size pplicable size 50 850 ccessory Description Nil B Bracket 1 1 Bracket is included, (but not assembled). How to Order Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Option 3 Multiple options can be selected. Refer to the table below for the available combinations. Indicate symbols in alphabetical order. Description Nil J guide 1 4 female threaded 5 R - reversal direction T With element service indicator 5 piping and piping for a stop valve such as ball valve are required. uto drain 2 Description Nil Without auto drain (With drain cock 3 4 ) D N.O. (Normally open) port is open when pressure is not applied. 2 Refer to the following table for the available combinations of the auto drain specifications and options. 3 When the option J is selected, the auto drain and drain cock are not available. 4 Body size 850 is equipped with a ball valve (Rc3/8). Mount a piping adapter -P0 (page 27) to the ball valve if NPT3/8 female threaded is required. uto Specifications/Option Combinations : vailable : Not available uto drain specifications/option uto drain specifications Option pplicable model D J R T MH50 MH850 uto drain specifications Option N.O. auto drain guide 1 4 - reversal direction D J R With element service indicator T H HW T B G K MG FF M MD MH ME MF D D 243

MH Series Flow Rate Characteristics (Representative values)/select the model under the max. flow capacity line. ( Element oil saturation Initial condition) Note) Compressed air over max. flow capacity line in the table below may not meet the specifications of the product. MH150C MH450C MH850 Inlet air pressure ir pressure Inlet air pressure capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) MH250C MH550C Inlet air pressure ir pressure capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) MH350C MH50 Inlet air pressure ir pressure capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) 244

Micro Mist Separator with Pre-filter MH Series Construction MH150C to 550C, MH50 MH850 q r w Replacement Parts No. Description Material 4 Element assembly Glass fiber, pplicable model Except option F Component Parts No. Description Material Note 1 2 3 Body Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass e MH150C MH-EL150 others For option F MH-EL150-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) Refer to page 280 for replacement of auto drain. Inner/outer surface coating MH250C MH-EL250 MH-EL250-F MH350C MH-EL350 MH-EL350-F Note) The figure shows the drain cock specification. Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 24 through to 248 for details. Model MH450C MH-EL450 MH-EL450-F MH550C MH-EL550 MH-EL550-F MH50 MH-EL50 MH850 MH-EL850 H HW T B G K MG FF M MD MH ME MF D D 245

MH Series Dimensions MH150C to 550C P Q uto drain C: With auto drain (N.C.) D: With auto drain (N.O.) uto drain F R O D I Width across flats 24 1/4 female threaded The same thread type is used for the and. S, U: With differential pressure switch (with indicator) Y Z T: With element service indicator W X S Color of drain cock Gray: N.C. Black: N.O. One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 Combination of D: With auto drain (N.O.) and H: For medium air pressure 34 H C K J U G T L M øv Bracket (ccessory) E B N 2 x port size 1/4 female threaded The same thread type is used for the and. Note) 23 for MH250C Option J: guide 1/4 female threaded guide Maintenance space M5 Note) The figure shows the drain cock specification. Model MH150C MH250C MH350C MH450C MH550C 24 Port size 1/8, 1/4 1/4, 3/8 3/8, 1/2 1/2, 3/4 3/4, 1 11 175 7 228 22 B 14 18 24 C 113 145 1 0 D 3 7 0 122 E 23 23 23 23 23 F 3 7 0 122 G Bracket related dimensions 15 H 17 13 225 24 281 I 5 80 0 0 J 24 28 31 33 K 5 8 8 T 7 U 7 L 12 12 14 18 18 M 7 V 12 15 15 N 35 40 50 55 5 O 54 P 70 Q 2 R 4.5 S 1. (mm) Element Differential service pressure indicator related switch related dimensions dimensions W 24 X 37 Y 32 Z 41 80 88 2 80 5 111 12 28 34 50 0 5 5 2 2.3 3.2 3.2 27 32 37 3 37 37 37 37 3 42 43 51 41 41 41 41

Micro Mist Separator with Pre-filter MH Series Dimensions MH50 uto drain D: With auto drain (N.O.) 12 180 7 uto drain cock: Black H HW T 10 13 4.5 One-touch fitting Thread type Rc, G: ø Thread type NPT: ø3/8 Option 34 J: guide 1/4 female threaded B 10 337 253 15 40 11 150 Bracket (ccessory) 314 32 85 guide Width across flats 24 1/4 female threaded The same thread type is used for the and. T: With element service indicator 55 37 G K MG FF M MD MH ME Maintenance space 23 M5 2 x port size 1, 11/2 female threaded MF D Note) The figure shows the drain cock specification. D 247

MH Series Dimensions MH850 2 1 2 180 18 180 24 () 3 15 13 2 184 1 Bracket ccessory 42 View B 30 348 2 x port size 11/2, 2 female threaded Drawing of view B 44 41 uto drain D: With auto drain (N.O.) uto drain 58 23 Rc 3/8 3/8 female threaded The same thread type is used for the and. Maintenance space Option T: With element service indicator 248

Super Mist Separator ME Series RoHS Can separate and adsorb aerosol state fine oil particles in compressed air and change the oil lubricating compressed air to oilless air or equivalent. Use this product for filtration of compressed air requiring higher clean air for painting lines, compressed air for clean rooms and/or equipment where oils must be avoided. The replacement time of the element is indicated by a color change. When the element becomes saturated with oil content, a red color spot will begin to appear on the front surface. When the red color spot becomes visible, replace the element immediately. Caution Be sure to use either the M, MD, or MH series as a pre-filter. Modular connection is possible with ME150C to 550C. (For details, refer to page 2.) ME150C to 350C ME450C/550C Model Model ME150C ME250C ME350C ME450C ME550C ME50 ME850 Note) Rated flow (L/min (NR)) 0 500 00 00 3700 000 100 Port size Weight (kg) 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3 4, 1 0.3 0.48 0.8 1.3 2.0 4.2.5 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics and Maximum Flow Capacity Line (page 252). Specifications Fluid Max. operating pressure Min. operating pressure Proof pressure mbient and fluid temperature Filtration rating Note 2) Cleanliness at outlet 1, 1 1 2 1 1 2, 2 Compressed air 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.01 µm (Filtration efficiency:.%) Less than 0 particles of 0.3 µm or larger per cubic foot [Less than 35 particles per liters (NR)] Max. 0.01 mg/m Oil mist density at outlet 3 (NR) ( 0.008 ppm) 1. Replace the element when a red color spot occurred on the Note 1) surface. Element replacement period 2. Even if a red color spot does not appear on the surface, the replacement interval for the element is when the pressure drop reaches 0.1 MPa or after two years of operation, whichever comes first. Note 1) Failure to replace the element when the red color spot begins to appear will result in red-pigmented oil content leaking into the secondary side. If immediate element replacement is for some reason not an option, an MF must be installed on the secondary side and the element should be replaced as soon as possible. In such cases, the MF element should be replaced at the same time. Note 2) Depending on the operating conditions, only a miniscule amount of red pigment, which will not affect filtration performance, may leak into the secondary side. Prolonged use under such conditions may result in minimal red-pigmented residue on the interior of the piping on the secondary side. ccessory Part No. pplicable model Bracket assembly (with 2 mounting screws) Caution ME150C ME250C ME350C ME450C ME550C ME50 ME850 M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. H HW T B G K MG FF M MD MH ME MF D D ME50/850 Made to Order (For details, refer to page 272.) 24 B

ME Series ME150C to 550C Size 150 250 350 450 550 Thread type Type Nil Rc F G N NPT How to Order ME 550 C Option Multiple options can be selected. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) R - reversal direction V White vaseline ccessory Description Nil B Bracket Bracket is included, (but not assembled). Port size Port size 150 01 1/8 02 1/4 03 3/8 04 1/2 0 3/4 1 pplicable size 250 350 450 550 Options F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right) V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. B 250

Super Mist Separator ME Series ME50/850 ME 50 Size 50 850 Port size 14 1 1 1 2 2 Thread type Type Nil Rc F G N NPT Port size pplicable size 50 850 How to Order Option Description Nil R - reversal direction ccessory Description Nil B Bracket Bracket is included, (but not assembled). Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. H HW T B G K MG FF M MD MH ME MF D D 251

ME Series Flow Rate Characteristics (Representative values) /Select the model under the max. flow capacity line. (Element initial condition) Note) Compressed air over max. flow capacity line in the table below may not meet the specifications of the product. ME150C ME450C ME50 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ME250C ME550C ME850 capacity line capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) ME350C capacity line Maximum Flow Capacity Line ir flow rate (L/min (NR)) Model Selection Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The ME50 is obtained when the max. flow capacity line is above the intersecting point in the graph. capacity (m 3 /min (NR)) Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. 252 Inlet pressure (MPa)

Super Mist Separator ME Series Construction ME150C to 550C q ME50/850 Component Parts No. Description Material Note 1 2 3 Body Housing (Case) Sight glass luminum alloy luminum alloy Tempered glass Replacement Parts No. Description Material 4 r w Element assembly Glass fiber, others pplicable model Except option F For option F ME150C ME-EL150 ME-EL150-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) e Inner/outer surface coating ME250C ME-EL250 ME-EL250-F ME350C ME-EL350 ME-EL350-F Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 254 through to 25 for details. Model ME450C ME-EL450 ME-EL450-F ME550C ME-EL550 ME-EL550-F ME50 ME-EL50 ME850 ME-EL850 H HW T B G K MG FF M MD MH ME MF D D 253

O B S R T P Q F E Bracket (ccessory) M øw I J V D N L U K G C Maintenance space ME150C to 350C (mm) ME150C ME250C ME350C Model Port size Bracket related dimensions 83 3 132 1/8, 1/4 1/4, 3/8 3/8, 1/2 B 14 18 C 54 73 8 D 3 7 0 E 7.5 5 5 F 3 7 0 G I 121 150 N 5 80 J 24 28 K 5 8 8 U 7 V 7 L 12 12 14 M 7 W 12 O 35 40 50 P 70 80 5 Q 2 28 34 R 54 80 S 4.5 5 5 T 1. 2 2.3 Dimensions ME Series 2 x port size 254

E R Q P D T Bracket (ccessory) L M U N øw V J K C I D H G Maintenance space B O F ME450C/550C ME450C ME550C Model Port size Bracket related dimensions 151 187 1/2, 3/4 3/4, 1 B 24 C 5 130 D 122 E 3 3 F 122 G 15 H 3 44 I 172 N 0 0 J 31 33 K U V L 18 18 M W 15 15 O 55 5 P 111 12 Q 50 0 R 88 2 T 3.2 3.2 (mm) Dimensions Super Mist Separator ME Series 2 x port size 255 H HW T B G K MG FF M MD MH ME MF D D ME

K M ME Series Dimensions ME50/850 Bracket ccessory N L 3 View B J 2 x port size Drawing of view B Maintenance space Model Port size ME50 1, 11 2 21 ME850 1 1 2, 2 403 B 32 42 C 17 235 D 10 2 E F 10 2 G H I 314 40 J 40 30 K 15 15 Bracket related dimensions L 24 M 11 13 N 150 180 O 85 1 P 180 2 Q 7 1 R 13 184 (mm) S 4.5 25

Odor Removal Filter MF Series RoHS Efficiently can remove odor in compressed air with an activated carbon element. Use this unit for applications sensitive to odors, such as for clean rooms. Can remove odor and gas ingredients in compressed air. ctivated carbon element with large filtration area. Easy replacement of elements. Caution Be sure to use the ME series as a pre-filter. Modular connection is possible with MF150C to 550C. (For details, refer to page 2.) MF150C to 350C MF450C/550C Model Port size Model Note) Rated flow (L/min (NR)) Weight (kg) MF150C MF250C MF350C MF450C MF550C MF50 MF850 0 500 00 00 1 8, 1 4 1 4, 3 8 3 8, 1 2 1 2, 3 4 3700 3 4, 1 000 100 0.3 0.48 0.8 1.3 2.0 4.2.5 Note) capacity at 0.7 MPa. capacity varies depending on the operating pressure. Refer to Flow Rate Characteristics (page ) and Maximum Flow Capacity Line (page 25). Specifications Fluid Max. operating pressure Min. operating pressure Proof pressure mbient and fluid temperature Nominal filtration rating Cleanliness at outlet Oil mist density at outlet Element replacement period ccessory Part No. pplicable model Bracket assembly (with 2 mounting screws) Caution Compressed air 1.0 MPa 0.05 MPa 1.5 MPa 5 to 0 C 0.01 µm (Filtration efficiency:.%) Less than 0 particles of 0.3 µm or larger per cubic foot [Less than 35 particles per liters (NR)] (The ME series is required on the inlet side.) Max. 0.004 mg/m 3 (NR) ( 0.0032 ppm) (The ME series is required on the inlet side.) 1. Replace the element when you notice an odor coming from the outlet side. 2. Even if the deodorization performance is normal, the replacement interval for the element is when the pressure drop reaches 0.1 MPa or after two years of operation, whichever comes first. MF150C MF250C MF350C MF450C MF550C MF50 1, 1 1 2 1 1 2, 2 MF850 M-BM1 M-BM2 M-BM3 M-BM4 M-BM5 BM5 BM57 Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages to 8 for ir Preparation Equipment Precautions. H HW T B G K MG FF M MD MH ME MF D D MF50/850 Made to Order (For details, refer to page 272.) 257 B

MF Series MF150C to 550C MF 550 C Size 150 250 350 450 550 Thread type Type Nil Rc F G N NPT How to Order Option Multiple options can be selected. Indicate symbols in alphabetical order. Description Nil F Rubber material: FKM H For medium air pressure (1. MPa) R - reversal direction V White vaseline ccessory Description Nil B Bracket Bracket is included, (but not assembled). Port size Port size 150 01 02 03 04 0 1/8 1/4 3/8 1/2 3/4 1 pplicable size 250 350 450 550 Options F: Rubber material: FKM FKM is used for the parts such as O-ring and gasket. H: For medium air pressure (1. MPa) Can be used up to 1. MPa at maximum. R: - reversal direction Flow direction: Right to left (Flow direction of the standard: Left to right.) V: White vaseline The body/housing is degreased, and the grease used for the parts requiring lubrication has been changed to white vaseline. B 258

Odor Removal Filter MF Series How to Order MF50/850 MF 50 14 Size 50 850 Model Selection Thread type Type Nil Rc F G N NPT Port size 1 1 1 2 2 Port size pplicable size 50 850 Select a model in accordance with the following procedure taking the inlet pressure and the max. flow capacity into consideration. (Example) Inlet pressure: 0. MPa capacity: 5 m 3 /min (NR) 1. Obtain the intersecting point of inlet pressure and max. flow capacity in the graph. 2. The MF50 is obtained when the max. flow capacity line is above the intersecting point in the graph. Note) Make sure to select a model that has the max. flow capacity line above the obtained intersecting point. With a model that has the max. flow capacity line below the obtained intersecting point, the flow rate will be exceeded, thus leading to a problem such as being unable to satisfy the specifications. Option Description Nil R - reversal direction ccessory Description Nil B Bracket Bracket is included, (but not assembled). Maximum Flow Capacity Line capacity (m 3 /min (NR)) Made to Order s are only added at the end for Made to Order. Refer to page 272 and later for the contents of Made to Order, How to Order, and the applicable models. Inlet pressure (MPa) H HW T B G K MG FF M MD MH ME MF D D 25

MF Series Flow Rate Characteristics (Representative values)/select the model under the max. flow capacity line. (Element initial condition) Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. MF150C MF550C MF00 capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) MF250C MF50 MF00 capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR)) MF350C MF800 capacity line MF450C ir flow rate (L/min (NR)) MF850 ir flow rate (m 3 /min (NR)) capacity line capacity line ir flow rate (L/min (NR)) ir flow rate (m 3 /min (NR))

Odor Removal Filter MF Series Construction MF150C to 550C q MF50/850 r w Component Parts No. 1 2 3 Description Body Housing (Case) Sight glass Material luminum alloy luminum alloy Tempered glass Replacement Parts No. Description Material pplicable model Except option F For option F MF150C Element 4 Glass fiber, MF-EL150 assembly others MF-EL150-F Element assembly: With gasket (1 pc.) and O-ring (1 pc.) e Note Inner/outer surface coating MF250C MF-EL250 MF-EL250-F MF350C MF-EL350 MF-EL350-F Note) Sight glass is indicated in the figure for easy understanding of component parts. However, it differs from the actual construction. Refer to dimensions on pages 22 to 24 for details. Model MF450C MF-EL450 MF-EL450-F MF550C MF-EL550 MF-EL550-F MF50 MF-EL50 MF850 MF-EL850 H HW T B G K MG FF M MD MH ME MF D D 21

O B S R T P Q F E M øw I J V D N L U K G C 2 x port size MF150C MF250C MF350C 83 3 132 1/8, 1/4 1/4, 3/8 3/8, 1/2 B 14 18 C 54 73 8 D 3 7 0 E 7.5 5 5 F 3 7 0 G I 121 150 N 5 80 J 24 28 K 5 8 8 U 7 V 7 L 12 12 14 M 7 W 12 O 35 40 50 P 70 80 5 Q 2 28 34 R 54 80 S 4.5 5 5 T 1. 2 2.3 MF150C to 350C Dimensions Bracket (ccessory) Maintenance space Model Port size Bracket related dimensions (mm) 22 MF Series

E R Q P D T L M U N øw V J K C I D H G B O F 2 x port size MF450C MF550C 151 187 1/2, 3/4 3/4, 1 B 24 C 5 130 D 122 E 3 3 F 122 G 15 H 3 44 I 172 N 0 0 J 31 33 K U V L 18 18 M W 15 15 O 55 5 P 111 12 Q 50 0 R 88 2 T 3.2 3.2 MF450C/550C Dimensions Bracket (ccessory) Maintenance space (mm) Model Port size Bracket related dimensions 23 Odor Removal Filter MF Series H HW T B G K MG FF M MD MH ME MF D D MF

K M MF Series Dimensions MF50/850 3 Bracket ccessory N L View B Drawing of view B Maintenance space J 2 x port size Model MF50 MF850 Port size B C D E 1, 11 2 21 32 17 10 1 1 2, 2 403 42 235 2 F 10 2 G H I 314 40 J 40 30 K 15 15 Bracket related dimensions L 24 M 11 13 N 150 180 O 85 1 P 180 2 Q 7 1 R 13 184 (mm) S 4.5 24

uto Operating State and Proper Use of Float Type uto uto drain N.O. Normally open N.C. Normally closed Compressor When pressure is not applied (fter exhausting residual pressure) discharged (Open) Float Piston Orifice not discharged (Close) Float Piston Orifice Proper Use When pressure is not applied (fter exhausting residual pressure) not accumulated Do not want to accumulate drain generated at the inlet side when pressure is not applied. Before drain accumulates not discharged (Close) When pressure is applied Cold climates Want to prevent troubles caused by freezing. When drain accumulates discharged (Open) For both N.O. and N.C., the drain can be discharged manually by turning the drain cock to the O position. (Except for medium air pressure, FF75B, M 850, and free standing type) cock Open 0.75 kw or more Close Minimum operating pressure (Outlet pressure) 0.1 MPa or more M 150 to 850 FF2 to 75 0.15 MPa or more M 150 to 550 FF2 to 22 Recommended auto drain N.O. Note) Normally open H HW T B G K MG FF M MD MH ME MF D D Less than 0.75 kw accumulated N.C. Normally closed Note) For N.O. (Normally open) type, the drain discharge passage is open when pressure is not applied. For this reason, the drain exhaust port is not closed completely in a compressor with a small supply amount (less than 0.75 kw) and the air will ceaselessly blow out. 25

Optional ccessories Spacer for Modular Connection Use a spacer listed below when connecting modular type FF2C to 22C, M 150C to 550C. The spacer must be ordered separately. (Note: Spacer with bracket (Y0T- to Y00T-) cannot be used.) Caution Modular connection Mount the attached bracket on one side when connecting 2 sets. Mount the attached brackets on both sides when connecting 3 sets or more. s a guideline for the number of brackets, one bracket should be mounted for every 2 products. Combination examples of modular type products rrangement example MH250C- B 1 pc. ME250C 1 pc. Y300-1 pc. Spacer: Y300- Bracket 158 rrangement example MH250C- B 1 pc. ME250C 1 pc. MF250C- B 1 pc. Y300-2 pcs. 240 13 175 13 175 ME250C ME250C MF250C- B Spacer (15) MH250C- B MH250C- B (23) D Center of F.R.L. body B C Y0- Y400- Model Y0- Y300- Y400- Y500- Y00- B C D 3.2 4.2 5.2 5.2.2 31.2 43.4 53 57 7. 15. 21.7 2.5 28.5 33.8 44. 57. 8.5 75. 2.5 Model FF2C, M 150C FF4C, M 250C FF8C, M 350C FF11C, M 450C FF22C, M 550C (Spacer width) Seal Replacement Parts Description Seal Note) ssembly of 2 O-rings 2 Material HNBR Y0- Y2P-050S Y300- Y3P-050S Part no. Y400- Y4P-050S Y500- Y5P-050S Y00- YP-050S