P1H INITURE COINTION UNITS ilter/regulators and lubricators P1H - 1/8, 1/4 Combinations of filterregulators and lubricators can be ordered as pre-assembled units Complete control of filtration, regulation and lubrication at a single point icro-fog versions for most general purpose pneumatic applications TECHNICL DT edium: Compressed air only aximum inlet pressure: 10 mbient temperature: -20 C... +50 C Consult our Technical Service for use below +2 C Pressure range: 0,3... 8, TERILS ody: zinc alloy owls: polycarbonate ilter element: polypropylene Elastomers: nitrile kg ODELS uto CCESSORIES Neck bracket auge 0 10 1/8 0,35 P1H-100-3Q P1H-100-3Q 18-025-003 18-013-989 1/4 0,35 P1H-200-3Q P1H-200-3Q 18-025-003 18-013-989 P H- - Integral wall bracket Without (P1H Combination Unit) 1 With T PT ISO Rc taper ISO parallel 1/8" 1 1/4" 2 ilter/regulator bowl Outlet pressure djustment range* psig Relief type auge Transparent 0,3... 8, 5... 125 Relieving Without 01 Transparent 0,3... 8, 5... 125 Non relieving Without 02 Transparent 0,3... 3.5 5... 50 Relieving Without 04 Transparent 0,3... 3.5 5... 50 Non relieving Without 0 etal 0,3... 8, 5... 125 Relieving Without 41 etal 0,3... 8, 5... 125 Non relieving Without 42 etal 0,3... 3.5 5... 50 Relieving Without 44 etal 0,3... 3.5 5... 50 Non relieving Without 4 * Do not use these units to control pressures outside of the specified ranges. -088 Lubricator reservoir Transparent with Transparent without etal with etal without Q ilter/regulator element 5 μm 1 40 μm 3 ilter/regulator utomatic www.norgren.com/info/en-088
98** 94*** 78**** 211# 10 42 8 28 LOW CHRCTERISTICS 8 8 Outlet pressure 4 Outlet pressure 0 2 4 8 10 DIENSIONS 90 : 1/4" Inlet pressure: 7 Range: 0,3... 7 : 1/4" Inlet pressure: 10 Range: 0,3... 7 4 2 2 0 ir flow 0 0 2 4 8 10 ir flow 3 28-44 # inimum clearance to remove bowl ** ***utomatic ****Without. -089
INITURE ENERL PURPOSE ILTERS 07-1/8, 1/4 07 Direct ported filters with high water removal efficiency utomatic s supplied as standard High flow miniature unit Transparent bowl for 30 visibility TECHNICL DT edium: Compressed air only aximum inlet pressure: 10 mbient temperature: -34 C... +50 C Consult our Technical Service for use below +2 C TERILS owl: polycarbonate to S 005, zinc alloy (optional) ody: zinc alloy Elastomers: neoprene & nitrile ilter element: polypropylene ODELS CCESSORIES SERVICE KIT low* () uto Wall bracket uto 1/8 9 07-100-3T 07-100-3T 5939-0 07-KIT40 07-KIT40 1/4 11,5 07-200-3T 07-200-3T 5939-0 07-KIT40 07-KIT40 *Typical flow with,3 inlet pressure and 0,5 pressure drop 07-00- 1/8" 1 1/4" 2 PT ISO Rc taper ISO parallel owl Transparent etal T Element 5 μm 1 40μm 3 Drain utomatic -090 www.norgren.com/info/en-090
LOW CHRCTERISTICS Inlet pressure () Pressure drop 0, 0,5 0,4 0,3 0,2 0,1 1,0 1, 2,5 4,0,3 8,0 10,0 : 1/4 40 μm element 2 4 8 10 12 14 1 18 20 ir flow DIENSIONS C racket D * Ø E utomatic * inimum clearance required to remove bowl Series Drain C Ø kg Series D E H 07 1/8, 1/4 uto 104 154 10 42 37 0,13 07 1/8, 1/4 35 34 52-108 158 10 42 37 0,13-091
INITURE OIL REOVL ILTERS 39-1/8, 1/4 39 High efficiency coalescing oil-removal filters aximum remaining oil content 0,01 mg/m 3, particle removal to 0,01 μm TECHNICL DT edium: Compressed air only aximum inlet pressure: 10 (transparent bowls) 17 (metal bowls) Remaining oil content: 0,01 mg/m 3 maximum Particle removal: 0,01 μm mbient temperature: -34 C... +50 C transparent bowls -34 C... +5 C metal bowls Consult our Technical Service for use below +2 C TERILS owl: polycarbonate to S 005, zinc alloy (optional) ody: zinc alloy Elastomers: neoprene & nitrile ain filter element: synthetic fibre & polyurethane foam ODELS CCESSORIES SERVICE KIT low* owl kg uto () Wall bracket 1/8 2,8 Transparent 0,13 39-100-0T 39-100-0T 5939-0 4141-10 2,8 etal 0,23 39-100-0 39-100-0 5939-0 4141-10 1/4 3 Transparent 0,13 39-200-0T 39-200-0T 5939-0 4141-10 3 etal 0,23 39-200-0 39-200-0 5939-0 4141-10 # aximum flow with,3 inlet pressure to maintain stated oil removal performance. or optimum coalescing element life a pre-filter should be fitted to remove coarse particles. oil removal filters are not recommended in service where plant maintenance is irregular. Consult our Technical Service for further details. 39-00- 1/8" 1 1/4" 2 PT ISO Rc taper ISO parallel Drain utomatic owl Transparent etal T Element Coalescing 0-092 www.norgren.com/info/en-092
TYPICL PERORNCE CHRCTERISTICS Inlet pressure aximum flow * () 39 1 1,2 3 2,0 5 2,7,3 3,0 7 3,1 9 3, * aximum flow to maintain stated oil removal performance DIENSIONS C racket E D # utomatic # inimum clearance required to remove bowl Series Drain C Ø kg Series D E 39 1/8, 1/4 uto 104 154 10 42 37 0,13 108 158 10 42 37 0,13 39 1/8, 1/4 35 34 52 LOW CHRCTERISTICS Inlet pressure () Pressure drop 0, 0,5 0,4 0,3 0,2 0,1 2,5 4,0,3 8,0 10,0 : 1/4 Element: Dry 1 2 3 4 5 ir flow -093
INITURE PRESSURE REULTORS R07-1/8, 1/4 R07 iniature regulators for general purpose pneumatic applications Relieving operation as standard Non-rising adjusting knob with snap-action lock Options include non-relieving models and alternative spring ranges TECHNICL DT edium: Compressed air only aximum inlet pressure: 20 auge ports: Rc1/8 mbient temperature: -34 C... +5 C Consult our Technical Service for use below +2 C Pressure range: 0,3... 10 TERILS ody: zinc alloy djusting knob: acetal resin Elastomers: nitrile low* () kg ODELS Pressure 0,3 7 Pressure 0,5 10 CCESSORIES Neck bracket auge 0 10 Panel nut SERVICE KIT 1/8.5 0,19 R07-100-RNK R07-105-RN 18-025-003 18-013-989 292-89 (Plastic nut) R07-KITR 1/4 7 0,19 R07-200-RNK R07-205-RN 18-025-003 18-013-989 292-04 (etal nut) R07-KITR *Typical flow with 10 inlet pressure,.3 set pressure and 1 drop from set. R07-0 - Size 1/8" 1 1/4" 2 Option Standard 0 H.P. unit, 10 (150 psig) 5** * Outlet pressure can be adjusted to pressures in excess of, and less than, those specified. Do not use these units to control pressures outside of the specified ranges. ** When specifying 10 (150 psig) unit, eg. R07-205-RN, also note correct code at th digit. PT ISO Rc taper ISO parallel Outlet pressure adjustment ranges* 0,1... 0,7 0,3... 3,5 E 0,3... 7 K 0,3... 10 ** auges With Without N Diaphragm Relieving Non relieving R N -094 www.norgren.com/info/en-094
LOW CHRCTERISTICS 8 Inlet pressure (10 ) : 1/4 Range: 0,3... 7 Outlet pressure 4 2 0 0 2 4 8 10 ir flow DIENSIONS ø 28 racket ø 30 max. (42) 4 24 24 75 19 23 3 28-44 34 42 54 Weight: 0,19 kg ø 40-095
INITURE ILTER/REULTORS 07-1/8, 1/4 07 ilter-regulators for all general purpose pneumatic applications High performance design provides high flow with minimum pressure drop Non-rising adjusting knob has snap-action lock Transparent bowl for 30 visibility etal bowl for high pressures Standard options include nonrelieving models, metal bowls and alternative pressure ranges TECHNICL DT edium: Compressed air only aximum inlet pressure: 10 auge ports: Rc1/8 Pressure range: 0,3...10 mbient temperature: -34 C... +50 C Consult our Technical Service for use below +2 C TERILS ody: zinc onnet: acetal Valve: brass/nitrile Valve seat: acetal owl: transparent polycarbonate; metal zinc Element: sintered polypropylene Elastomers: nitrile low* () ODELS CCESSORIES SERVICE KIT uto ounting bracket and nut auge 0 10 Panel nut uto 1/8,2 07-101-3K 07-101-3K 18-025-003 18-013-989 292-89 (Plastic nut only) 07-KIT40R 07-KIT40R 1/4,5 07-201-3K 07-201-3K 18-025-003 18-013-989 292-04 (etal nut only) 07-KIT40R 07-KIT40R *Typical flow with 10 inlet pressure,.3 set pressure and 1 drop 07- - 1/8" 1 1/4" 2 PT ISO Rc taper ISO parallel owl Relief type auge Transparent Relieving Without 01 Transparent Non relieving Without 03 etal Relieving Without 33 etal Non relieving Without 35 etal Relieving Without 05** etal Non relieving Without 07** * Outlet pressure can be adjusted to pressures in excess of, and less than, those specified. Do not use these units to control pressures outside of the specified ranges. ** When specifying 10 (150 psig) unit, eg. 07-205-3, also note correct code at 5th and th digits. Outlet Pressure djustment Ranges* 0,1... 0.7 0,3... 3.5 E 0,3... 7 K 0,3... 10 ** Element 5 μm 1 40 μm 3 Drain utomatic -09 www.norgren.com/info/en-09
DIENSIONS N racket # D C * 3 28-44 utomatic # inimum clearance required to remove bowl *1/8" SP connection Drain C D Panel Ø Panel depth kg 1/8, 1/4 uto 10 210 8 28 41 30 0... 0,2 14 214 8 28 41 30 0... 0,2 LOW CHRCTERISTICS Inlet pressure (10 ) : 1/4" 40 μm element Range 0,3... 7 Outlet pressure 5 4 3 2 1 1 2 3 4 5 7 8 9 10 ir flow -097
INITURE LURICTORS L07-1/8, 1/4 L07 icro-fog lubricators provide a fine mist for most general purpose pneumatic applications Transparent bowl for 30 visibility TECHNICL DT edium: Compressed air only aximum inlet pressure: 10 Start point: 0,24 inimum flow required for lubricator operation at,3 inlet pressure mbient temperature: -20 C... +50 C Consult our Technical Service for use below +2 C TERILS owl: polycarbonate, zinc alloy (optional) ody: zinc alloy Sight-feed dome: transparent nylon Elastomers: neoprene & nitrile ODELS CCESSORIES SERVICE KIT low* () kg Neck bracket 1/8 5 0,13 L07-100-PQ 18-025-003 L07-KIT 1/4,7 0,13 L07-200-PQ 18-025-003 L07-KIT *Typical flow with.3 inlet pressure and 0.5 pressure drop L07-00-P 1/8" 1 1/4" 2 PT ISO Rc taper ISO parallel owl and Transparent without etal with Q -098 www.norgren.com/info/en-098
DIENSIONS racket * C E D Without # inimum clearance required to remove bowl Series C Ø kg Series D E H L07 1/8, 1/4 120 183 42 41 37 0,1 L07 1/8, 1/4 19 28... 44 3 - LOW CHRCTERISTICS Inlet pressure () 0, 1,0 2,0 4,0,3 8,0 10,0 Pressure drop 0,5 0,4 0,3 0,2 0,1 : 1/4 1 2 3 4 5 7 8 9 10 ir flow -099
INITURE RELIE VLVES Diaphragm type V07-1/8, 1/4 V07 Protect compressed air systems from over-pressurisation Norgren pressure relief valves comply with category O(S.E.P.) and category 1 of the Pressure Equipment Directive 97/23/EC. TECHNICL DT edium: Compressed air only auge ports: Rc1/8 Relief port: s inlet port Pressure range: 0,3...9 mbient temperature: -34 C... +5 C Consult our Technical Service for use below +2 C Relief pressure adjustment range: 0,1... 10 TERILS ody: zinc alloy djusting knob & bonnet: acetal resin Valve seat: polyphenylene Elastomers: nitrile ODELS CCESSORIES SERVICE KIT kg Neck bracket auge 0 10 1/8 0,13 V07-100-NNL 18-025-003 18-013-989 V07-KIT 1/4 0,13 V07-200-NNL 18-025-003 18-013-989 V07-KIT V07-00-N Size 1/8" 1 1/4" 2 auges With Without DIENSIONS 28 N racket kit (V07) 24 LOW CHRCTERISTICS PT ISO Rc taper ISO parallel Relief pressure adjustment ranges 0,1... 0,7 0,3... 3,5 E 0,3... 7 K 0,3... 10 8 7 Ø 30 max. 24 8 75 34 42 Relief pressure 5 4 3 2 R c 1 /8 1 : 1/4 41 1 2 3 4 5 7 8 9 10 3 28-44 ir flow -100 www.norgren.com/info/en-100
INITURE ERNE DRIERS W07-1/4 W07 Removes water vapour from compressed air Provides dewpoint suppression up to 44 C below the ambient temperature, depending on air flow through the membrane Dewpoint suppression of 11 C below the ambient temperature is suitable for most industrial applications W07 available for in-line installation only Easy installation, no power required aintenance free with proper pre-filtration inimal pressure drop TECHNICL DT edium: Compressed air, pre-filtered to 0,01 μm and oil free aximum operating pressure: 10 mbient temperature: -20 C... 80 C* *ir supply must be dry enough to avoid ice formation at temperatures below +2 C. Required pre-filter: eneral purpose filter (5 μm element) and an oil removal filter (0,01 μm particle removal) with equivalent pipe and flow capacity equal to or greater than the membrane air dryer Selection programme available on request TERILS ody and end caps: nodized aluminium embrane: polymeric materials Nominal flow ()* Outlet Inlet Differential pressure () kg ODELS 1/4 1,00 1,0 0,028 0,39 W07-2N-NN *7 inlet pressure, C ambient temperature and dew point suppression of 11 C PT ISO parallel DIENSIONS W07-2N-NN 40 30 www.norgren.com/info/en-101 ºC 40 30 W07-2 N-NN LOW CHRCTERISTICS W07-2N-NN Dewpoint suppression C D E : 1/4" Range: 0,1... 1,0 Inlet air dewpoint: C Inlet 20 pressure () = 3,5 = 5 10 C = 7 D = 8,5 E = 10 0 0 0,5 1,0 1,5 2,0 2,5 ir flow low () 1,00 2,40 4,75 C 9,50 D 14,20 E -101