lectro-hydraulic control valve his valve uses a D solenoid in a traditional 4- way solenoid valve to create a solenoid valve capable of both direction switching and highspeed control. he lineup consists of the direct system 01 size and the pilot system 03, 04, and 06 sizes. Direction control is performed by supplying input current to one of the two tem odel o. R-YDRU RR W D DR R VV lectro-hydraulic roportional low and Direction ontrol Valve eatures Specifications SD-G01-** 20-12 proportional solenoid valves, and the size of the flow rate is controlled in accordance with the size of the input current. his type of valve can be used for remote control and shockless acceleration and deceleration control, and for simple configuration of hydraulic circuits. SD-G03-** 40 80 -(**)-12 SD-G04- **140-(**)-12 aximum perating ressure a{kgf/cm 2 } 25{255} SD-G06- **2-(**)-13 Rated low Rate l/min /20(ote 1) 40/80(ote 1) 140(ote 1) 2(ote 1) aximum low Rate l/min 25(ote 2) (ote 2) 140(ote 2) 2(ote 2) ilot ressure a{kgf/cm 2 } t least 1.0{}(ote 3) to 2l/min 25a ilot low Rate l/min t least 2(ote 4) t least 3(ote 4) t least 5(ote 4) ort llowable ack nternal Drain: 2.5 {25.5} 2.5{25.5} ressure a{kgf/cm 2 } xternal Drain: 21 {214} Rated urrent m 8 oil Resistance Ω 20(20 ) ysteresis % 5 max.(ote 5) Response ime S 0.04(ote 6) 0.05(ote 6) 0.08(ote 6) 0.1(ote 6) Weight kg 2.2 7.2 15 ote) 1. Value when pressure drop volume to and is Δ = 1.0a {kgf/cm 2 }. 2. ndicates maximum throughput volume value between each port. 3. ndicates differential between the pilot port and tank port, or drain port. 4. Value when 0.1 second is assumed for the response time from zero to the rated flow volume. 5. Value when a achi-ujikoshi special amplifier is used. 6. Response time is typical value for a supply pressure of 14a {143kgf/cm 2 } and oil temperature of 40 (kinematic viscosity: 40mm 2 /s). xplanation of model o. SD G 03 5 80 (***) 12 Design number uxiliary symbol (an be combined in alphabetic sequence.) (or G03, G04, G06 size only) one: nternal pilot, external drain (standard) : nternal pilot, internal drain : xternal pilot, external drain : xternal pilot, internal drain G : odular pilot With pressure reducing valve (G-G01-1-21) (See ote n under andling. ) Rated flow rate (See the rated flow rate item in the specifications.) Spool type (See able 1.) ominal diameter: 01, 03, 04, 06 andling zir leeding n order to ensure stable control, loosen the air vent and bleed air from the valve before starting operation. or details, see the user's guide. x ort iping When configuring piping, ensure that the port (pilot valve port for the G03, G04, and G06 sizes) is filled with operating fluid. canual djusting Screw or the initial adjustment or when there is no input current to the valve due to an electrical problem or some other reason, the valve can be operated and valve pressure can be increased by rotating the manual adjustment screw clockwise (rightward). ormally, the manual adjusting screw should be rotated back fully to the left (counterclockwise). vvalve ounting rientation nstall the valve so the spool axis line is horizontal. bombining with a ressure ompensation Valve Use of the optional pressure compensation kit is recommended when higher precision flow rate control is required or in high-pressure applications. or details, see page -20. nf pilot pressure (SD-G03, G04, G06) exceeds a {2kgf/cm 2 } use a modular type port reduction valve (G-G01-1-21) at a setting of 2a {20kgf/cm 2 }. mn a system that requires large brake pressure during deceleration or a system that uses a vertical cylinder, equip a counter balance valve. Use a single rod, if the rod exit is not slowed sufficiently, use a counter balance valve on the rod.,aintain hydraulic operating fluid contamination so it is at least lass. Use of a G01 modular filter (bsolute: 8μm) is also helpful. (xample: aisei ogyo o., td. V-01-8-1) (ontinued on next page) able 1 Spool ype b ounting method G: Gasket type ump type SD: lectro-hydraulic proportional flow and directional control valve ydraulic ircuit SD-G01 SD-G03,G04 SD-G06 a b a b a 5 b a b DR a b DR a 6S DR DR -14
nstallation Dimension Drawings SD-G01 4- φ.5x11 counterbore φ 5.5 holes anual pressure adjusting screw 4- φ 7.5 ir vent (ir bleeding) (hex width across flats 3) 66 X 287.6.undled ccessories (Valve ounting olts) odel o. olt Size Q'ty ightening orque m{kgf cm} SD-G01 5 45l 4 5 to 7{ 51 to 71} SD-G03 6 35l 4 to 13{ 2 to 133} 6 45l 2 to 13{ 2 to 133} SD-G04 l 4 45 to 55{ 460 to 560} SD-G06 12 60l 6 60 to 70{ 6 to 715} or information about sub plates, see S-01Y- on page -3. Gasket Surface Dimensions (S 4401-03-02-0-4) SD-G03 S.b port port port (Used in the case of external pilot port.) 54 S.a 4 set screw (hex Width across flats 2) 4- φ11x11 counterbore port φ6.8 hole DR port (Used in the case of external drain.) 1.5 80 48 25.5 0Use an operating fluid that conforms to the both of the following. il temperature: 20 to 70 inematic Viscosity: 12 to 400mm 2 /s. he recommended kinematic viscosity range is 15 to 60mm 2 /s. SD-G03 ounting Gasket Surface Dimensions Gasket Surface ounting Dimensions (S4401-05-0-05) 46 6.4 xternal pilot port 5 to φ.5 (max.) xternal drain port port X 143.8 X 287.6 1 port 4 set screw (hex Width across flats 2) ir vent (ir bleeding) (hex width across flats 3) anual flow rate adjusting screw 70 min. 46 32.5 21.4 11 S.a S.b 87 112.5 135 178.5 3.2 16.7 27 37.3.8 54 8 62 4 min. 2 to φ 7 (max.) 4 to 6x12 tap SD-G04 2- φ 11x1 counterbore 4 38 170 φ6.6 hole port 4- φ 17.5x1 counterbore port (Used in the case of external pilot.) φ11 hole port port 20 S.a 34.1 1.6 140 X 287.6 X Y port Y S.b 27 35 1.6 6. 71.5 DR port (Used in the case of external drain.) 70 4 set screw (hex Width across flats 2) ir vent (ir bleeding) (hex width across flats 3) anual flow rate adjusting screw 4 12.5 126.5 1 35 33 36 uxiliary symbol G: quipping a modular type pilot reduction valve increases the height by 40mm. he gasket surface dimensions comply with the S standards shown below. SD-G04 S 4401-07-06-0-05 SD-G06 S 4401-08-07-0-05 SD-G S 4401--08-0-05 ote) he coil cover has an 4 set screw. o change the air vent orientation, loosen the 4 screw and then rotate the cover. fter bleeding air, tighten the cover and then secure it with the 4 screw. lectro-hydraulic control valve 2 2- φ 3 204 1-15
SD-G06 6- φ 21x2 counterbore φ13.8 holes port port DR port (Used in the case of external drain.) 46 2.1 port (Used in the case 12 of external pilot port.) 53.2 77 130.2 154 port X287.6 port set screw (hex Width across flats 2) ir vent (ir bleeding) (hex width across flats 3) anual flow rate adjusting screw S.b S.a 6 211.5 145.5 120 48 43 127.5 255 2- φ 6 58 116 erformance urves nput urrent low Rate haracteristics are characteristic when the or pressure drop is Δ = 1.0a {kgf/cm 2 }. ydraulic perating luid inematic Viscosity 32mm 2 /s or ressure low Rate haracteristics, the horizontal shaft valve differential pressure indicates the pressure drop volume of the entire control valve (between,,, ), and flow rate is measured at the oil motor. lectro-hydraulic control valve nput urrent low Rate haracteristics SD-G01 SD-G03 25 low rate l/min low rate l/min SD-G01-**20-12 20 15 5 SD-G01-**-12 0 0 200 400 600 800 0 nput current m SD-G06 2 SD-G06-**2-13 200 1 low rate l/min SD-G03-**80-12 75 25 SD-G03-**40-12 0 0 200 400 600 800 0 nput current m low rate l/min SD-G04 2 SD-G04-**140-12 200 1 0 200 400 600 800 nput current m 0 0 0 200 400 600 800 0 nput current m -16
ressure low Rate haracteristics low rate l/min 40 30 20 SD-G01-520-12 i=8m i=700m i=600m i=0m 0 5 15 20 25 {51} {2} {153} {204} {255} Valve differential pressure a{kgf/cm 2 } low rate l/min 125 75 25 SD-G03-580-12 i=8m i=700m i=600m 0 5 15 20 25 {51} {2} {153} {204} {255} Valve differential pressure a{kgf/cm 2 } low rate l/min 2 200 1 SD-G04-5140-12 i=8m i=700m i=600m 0 5 15 20 25 {51} {2} {153} {204} {255} Valve differential pressure a{kgf/cm 2 } 300 2 SD-G06-52-13 i=8m low rate l/min 200 1 ross-sectional Drawings SD-G01-****-12 i=600m i=0m 0 5 15 20 25 {51} {2} {153} {204} {255} Valve differential pressure a{kgf/cm 2 } 13 12 5 11 8 7 4 6 2 1 3 Seal art ist (it odel umber DS-G01-1) art o. art ame art umber Q'ty 6 S 568-012(R-0) 4 7 S 568-01(R-0) 2 8 R-0 22 2 S 568-016(R-0) 2 R-0 7 2 11 S-25(R-70-1) 2 12 R-70-1 20 2 13 Seal W00 2 ote) he materials and hardness of the conforms with S 2401. art o. 1 2 3 4 5 6 7 8 11 12 13 art ame ody Spool Retainer Spring oil Seal ote) oil model number D64-D2-17 lectro-hydraulic control valve
SD-G03-****-(**)-12 8 7 anual adjustment section (SD-G03, G04, G06, G) 4 set screw ir vent D DR 15 6 4 5 12 13 11 2 1 3 SD-G04-****-(***)-12 ote) he coil cover has an 4 set screw. When changing the orientation of the air vent, loosen the 4 screw and rotate the cover. Retighten after bleeding the air. ethods for hanging the ilot/drain System fter hange exagon Socket ead lug ilot nternal hange to port from. xternal hange from port to. Drain nternal hange from D to DR port. xternal hange from DR port to D. 7 8 15 R Y(DR1) X() lectro-hydraulic control valve art o. 1 2 3 4 5 6 7 8 11 12 13 14 15 4 12 6 5 2 1 11 16 art ame ody Spool over Retainer all Spring ilot spool Stopper Screw roportional solenoid ote) oil model number D64-D2 R 13 3 ross Section - 14 ross Section R-R ethods for hanging the ilot/drain System fter hange exagon Socket ead lug nternal Remove from ilot xternal nsert from nternal hange from to Drain xternal hange from to ote) single hex head plug ( 1/16) is required when changing to external pilot. ex ead lug: U-1/16 Seal art ist (it odel umber S-**) art- SD-G03 SD-G04 art ame o. art umber Q'ty art umber Q'ty R-0 12 5 R-0 22 4 11 R-0 2 R-0 2 12 R-0 28 2 R-0 34 2 13 R-0 6 R-0 2 14 R-0 8 3 it odel o. S G03 S G04 ote) he materials and hardness of the conforms with S 2401. -18
SD-G06-****-(***)-13 11 17 ilot, Drain System hange 16 8 R R X 8 6 7 12 13 14 15 Seal art ist (it odel umber S-G06) art o. art ame art umber Q'ty 12 R-0 28 4 13 R-0 20 2 14 R-0 G45 2 15 R-0 2 16 R-0 8 3 ote) he materials and hardness of the conforms with S 2401. X() Y(DR1) ross-sectional - ross-sectional R-R hanging the ilot and Drain onnections fter hange exagon Socket ead lug nternal Switch from to X. ilot xternal Switch from X to. nternal Switch from to. Drain xternal Switch from to. art o. 1 2 3 4 5 6 7 8 11 12 13 14 15 16 17 art ame ody Spool over Retainer all Spring Spring Screw in ilot spool Stopper roportional solenoid lectro-hydraulic control valve -1
ressure compensation valve kit Specifications odel o. tem -027-03040() -03080() -06170() aximum perating ressure a{kgf/cm 2 } 21{214} 25{255} 25{255} 21{214} ressure ompensation Differential ressure a{kgf/cm 2 } 1.0{} 0.6{6} 1.4{14} 0.8{8} aximum low Rate l/min 27 40 80 170 Weight kg 1.5 4.7 5.0 12 xplanation of model o. 03 040 () uxiliary symbol (See "andling.") one : nternal pilot : xternal pilot aximum low Rate (l/min) ominal diameter 01, 03, 06 ressure compensation valve kit andling zwhen using the pressure compensation kit, use an external pilot type for the SD valve (G03, 06). xn internal pilot type pressure compensation valve kit is used when the pilot flow rate is supplied from the port, without an eternal pilot port (p port) on the manifold. n external pilot type pressure compensation valve kit is used when there is an external pilot port (p port) on the manifold. lectro-hydraulic control valve nstallation Dimension Drawings ressure compensation valve kit -027-20
-03040() -03080() -06170() ote) ounting bolts are not included with the pressure compensation kit. Use the valve mounting bolt lists on pages D-3 through D-5 to select mounting bolts. lectro-hydraulic control valve DR DR nternal pilot xternal pilot -21