LEADING EDGE SAFETY. Weighted Base Guardrail Instruction Manual Complete Perimeter Fall Protection System

Transcription

1 AD D AFTY Complete Perimeter Fall Protection ystem Weighted Base uardrail nstruction Manual *WAR* erious injury or death may result if this product is used for purposes other than designed. The manufacturer provides the following instructions for the installation, use, and care of this equipment. t is the responsibility of the purchaser to understand and convey explicit instruction to each user. This eading dge afety product complies with the requirements of the Federal Occupational afety and ealth Administration (OA) when set up and used according to the manufacturers instructions. eading dge afety, C expressly disclaims any and all liability from injury, damage, or other loss resulting from improper or unau thorized installation or use of this product.

2 Weighted Base nstruction Manual Published by eading dge afety, C, Kansas City, MO 1345 Taney treet Kansas City, Missouri (T) Copyright 2015 by eading dge afety, C PRTD T UTD TAT OF AMRCA 1

3 PRODUCT OVRVW Use and imitations The Weighted Base uardrail can be used with many different applications when installed by a competent professional and the structure is capable of withstanding the weight of the system as determined by a competent professional. The Weighted Base uardrail system is intended for use as leading edge and roof opening protection as defined by OA tandards and meets and exceeds those tandards when properly designed and installed. O component of the Weighted Base uardrail system has been designed, tested or intended as an Anchorage point as defined by OA tandards and should VR be used as such. oisting and snap hook devices should never be attached to any component of the Weighted Base uardrail system. eading dge afety Weight Base uardrails are designed to prevent employees from falling when properly installed. While companies can provide safety training and safety systems, such as guardrail systems, every employee is responsible for their own safety and should act in a safe and responsible manner. n additional to fall protection such as guardrails, eading dge afety recommends implementing a Fall Protection Plans and safety training in accordance with OA Rule mproper use of eading dge afety products can result in serious injury or death. The Weighted Base uardrail should be used as a part of a complete fall protection system and plan. After a Fall or mpact All components that have been subjected to fall or impact forces must be removed from service immediately for inspection by qualified personnel and replaced if necessary. Before ach Use The Weighted Base uardrail system should be inspected prior to each use for wear, damage or deterioration, and defective components shall be removed from service. PCTO TP TP 1: Check for loose, bent or damaged parts. TP 2: Check fasteners/connectors for distortion, cracks, or other damage and proper torque. TP 3: All labels must be present and fully legible. TP 4: Check for corrosion on Parts. MATAC AD CAR: A. nspect all Weighted Base uardrail components before each use. B. Annually and before each use, inspect all fasteners for proper torque. C. Maintain paint finish to prevent corrosion. D. Replace damaged or deteriorated parts immediately. eneral afety Use common sense and safe work practices. The guardrails should not be used by persons whose ability or alertness is impaired by fatigue, intoxication, illegal or prescription drugs, or any other physical cause that exposes the user or others to injury. Always wear proper safety attire. Workers on the roof should be trained in accordance with OA tandards. 2

4 1.0 Assembly/etup WBP-F (WTD BA POT) RB-RA-10 (10 ORZOTA RA) RB-RA-8 (8 ORZOTA RA) RB-RA-120 ( ADJUTAB RA) RB-RA-70 (43-70 ADJUTAB RA) RB-RA-43 (29-43 ADJUTAB RA) RP-UC-000 (UVRA CORR) WB-000 (WTD BA) (5-OB KOB) 1.1 Place the Weighted Bases at the appropriate location based on drawing layout and/or location appropriate for field conditions, ensuring toe board pockets are parallel to the leading edge being protected. 1.2 nsert Weighted Base Post into receiver of Weighted Bases, ensuring drop-lock pins or insert rivet nuts are facing away from the leading edge. Tighten 5-obe Knob securely to ensure post are securely locked in place. 1.3 Attach appropriate length orizontal Rails to Weighted Base Post by either sliding rails on to drop-lock pins or fastening in to insert rivet nuts with bolts provided. When attaching horizontal rails using bolts and insert nuts, tighten bolts to recommended torque of 70 inch pounds for clean and dry bolts. 3

5 2.0 Proper ayout and Design 4 OUTRR (RQURD AT B, D, AD AY TRUPTO OF COTUOU CTO.) 10-0 MAX MMUM AD D V BOW RAD AD FOOW TAATO AD D TRUCTO PROR TO TAATO. UR YTM DO OT XCD OAD MT OF UBTRAT. DO OT D OR TA PRODUCT WT 10 OF VOTA CTRCA. VR TA DAMAD PRODUCT. DO OT TA PRODUCT O PPRY URFAC. DO OT TA PRODUCT O OPD URFAC. OY TA WTD BA OVR CA, DRY AD DBR-FR URFAC. DO OT T-OFF TO OR U AY COMPOT OF T YTM A A ACOR POT. DO OT U AY COMPOT OF T YTM FOR OT. PCT T YTM AFTR TAATO TO UR A COMPOT AR CURY ATTACD. PCT YTM AUAY FOR DAMA AD TO UR COMPOT AR CURY ATTACD. AY DAMA TO T F OUD B TRATD WT A RUT BTV PAT OR COAT. F YOU AR UUR OF PROPR D, TAATO, U OR CAR OF T T YTM, COTACT T MAUFACTUR WT AY QUTO OR COCR. 4

6 T PA TTOAY FT BAK 5

7 DAT -RVC: AMBD BY: (PRT AM) ATUR: APPDX B - Assembly, nspection and Maintenance og *** Please Copy This xample og and Review Before ach Use and During Regularly cheduled Maintenance *** COMPAY: TDD U OR OTR RVAT DTA: DAT: PCTD BY: OT CODTO OF: UPRT: UPRT RA COCTOR: RA: OTR MC PART: OT: DAT: PCTD BY: OT CODTO OF: UPRT: UPRT RA COCTOR: RA: OTR MC PART: OT: 6

8 1345 Taney treet orth Kansas City, Missouri Copyright 2015 by eading dge afety, C PRTD T UTD TAT OF AMRCA 7