Add more bike racks closer to building entries; consider hitching post style racks to save space; include cut sheets of proposed bike rack.

Transcription

1

2 July 29, 2009 Urban Design Commission City of Madison, Wisconsin 215 Martin Luther King Jr. Boulevard, Room LL-100 Madison, Wisconsin Re: Proposed Development at 7017 Mineral Point Road Initial and Final Approval Submittal Letter of Intent ka/jn: Dear Urban Design Commission Members: On behalf of CBL and Associates Properties, Inc., it is our pleasure to submit to you our application package for appearance at the August 5, 2009 UDC meeting to seek Initial and Final Approvals from the Commission. As the programming, tenants and use of the proposed building have not changed, this Letter of Intent will simply outline the revisions to the site plan, landscape plan and building design. These revisions are being presented in response to comments received at our last appearance before the Commission on July 15. Site and Landscape Plans Add more bike racks closer to building entries; consider hitching post style racks to save space; include cut sheets of proposed bike rack. Six more spaces were added to the east side of the building three each in proximity to the buildings primary entry points. There are now sixteen 6 x2 spaces provided on the proposed development. The bike parking spaces will each be outfitted with a Dero Bike Hitch, which allows flexible and efficient bike parking. Each rack can hold two bikes. Don t bring crosswalks to curb ramps at an angle. Better organize the pedestrian connections and ADA access. The ramp configurations were modified to be perpendicular to the curb. The pedestrian connection to Gammon Road was shifted north to accommodate a ramp that meets the curb at 90-degrees. Tighten curb radii at corners of building pad to promote traffic calming. For consistency, the curb radii were adjusted to match the design of the neighboring parking end islands: 10 on west side of building, 8 on east side. The sidewalks at each corner were re-designed to create room for landscape areas that will house boulders and ornamental grasses to keep cars from jumping the curb, thus protecting pedestrians at the sidewalk level.

3 July 29, 2009 Urban Design Commission - City of Madison, Wisconsin ka/jn: Page 2 Landscaping should be more special. Use material that has more height, shape and color. More new landscaping is proposed to provide interest and color, particularly at the very prominent northeast corner, where the pedestrian ramp meets the intersection. Material was selected to tolerate site conditions while providing seasonal color, buffering and enhancement to existing material to remain. A rock outcropping will be added to the northeast corner to create distinct planting areas and a gateway look. Add honeylocust and understory landscaping along the Smashburger patio to provide more screening from the parking area. Building Design The building was shifted south, thus widening the planting area to approximately ten feet. There is now ample room for proposed Skyline Honeylocust trees, an evergreen hedge and abundant perennials and ornamental grasses that will create lush landscaping along the outdoor dining area. Design is too neutral, too safe and too traditional. The forms, colors and materials were updated to be bolder, more modern and more out-of-theordinary. The tower at the retail space employs an asymmetrical form in a prominent copper color to punctuate the south corner of the building, while providing balance to the Smashburger tower at the north end. The use of metal panels broadens the elevations palette of colors, while bringing clean lines and a sleeker appearance to the design. Tower feature and detail along top of building looks too much like cornices. Put a different hat on the building. The south tower now features a metal soffit in non-traditional proportions that will emphasize the building s unique character. Metal coping along the top of the building will provide a finish detail that is flush to the face of the building, again representing a non-traditional style that steers clear of the cornice look so typical of suburban retail developments. Proportions of retail space s architecture too traditional. Proportions have been adjusted to be more like Smashburger, with glazing reaching above the canopy level. Smashburger too different from rest of the building. Carry either materials or forms throughout, without branding the entire building in Smashburger s look. Forms and colors were used to balance the building from north to south. The Smashburger brick is also used on the retail facade to help intermingle the design of both. Lessen the use of EIFS. Bring the higher quality materials into the design even more. Most of the EIFS was replaced with flat and corrugated metal panels, brick and cast stone accent bands.

4 July 29, 2009 Urban Design Commission - City of Madison, Wisconsin ka/jn: Page 3 We look forward to presenting the revised design to the UDC next week. In the meantime, if you would like to discuss or have questions, please do not hesitate to contact us. Very truly yours, ka architecture Chris Meske, ASLA, LEED-AP Senior Landscape Architect Site Planner c: File X:\Projects\09007\Documents\Letters Memos\ CAM LT LOI Urban Design Commission.doc/trk

5 ABOLITE EASTPORT LSI OUTDOOR LIGHTING BUILDING & WALL MOUNT DIMENSIONS 11 13/16" [299 mm] ARM MOUNT 6" [152 mm] PENDANT MOUNT 11 15/16" [302 mm] FIXTURE HOUSING/GUARD - Die cast aluminum. FINISH - Available in High Gloss and Architectural Textured polyester powder finishes. LAMP OPTIONS - 26, 32 and 42-Watt Compact Fluorescent Lamp (CFL) or low wattage, medium based Pulse-Start Metal Halide (PSMV) or Metal Halide (MH) lamps (available separately - consult factory). Incandescent is approved for up to 200-Watt maximum (lamp by other). MOUNTING - Pendant mount is top entry and may be used with 3/4 rigid stems, or a variety of gooseneck and pole brackets (see accessory section). Wall mount is designed for side entry 3/4 rigid conduit arm brackets. Surface mounted unit designed to mount over 4 recessed outlet box (box by other). Note: Electronic CFL or EMH electronic ballast, is supplied as part of the surface mount fixture, but must be ordered separately for the Pendant and Wall mount fixtures. GLOBE - 4 linear prismatic glass globe is fully tempered and heat resistant. GUARD - Die cast aluminum guard. Guard assembly easily removed as a unit by loosening 1/8 hex set screw and quarter turning assembly leaving globe intact and accessibly for lamping. SOCKET - Smart CFL socket design accepts both 26/32W (GX24q-3 base) and 42W (GX24q4 base). Metal Halide and Pulse- Start Metal Halide sockets are porcelain medium base and pulse rated. BALLASTS - All electronic ballasts are designed for v, +/-10%, 50/60 Hz. Designed to operate -30ºC/-20ºF with a Power Factor greater than 90%. Surface Fixtures include ballast. Pendant and Wall fixtures require Remote Ballast (specify separately). Postline ballast available for 26/32/42 CFL lamps only. Ø6 1/8" [156 mm] 2 1/4" [57 mm] Ø7 3/4" [197 mm] 3 3/8" [86 mm] All Abolite products available as Wall, Pole, & Ceiling Mounted and can be used Indoors 11 15/16" [304 mm] 13 1/16" [331 mm] SURFACE MOUNT CFL & INC SURFACE MOUNT EMH & CFL DIM wet location 03/16/ LSI INDUSTRIES INC. Project Name Catalog # Fixture Type Catalog No: EPT-S-26-CFL-UE-MSV-(GLOBE COLOR) Lamp Type: (1) PL-T26W/830/4P/ALTO The Lighting Practice Date: 07/01/2009 Fixture Type: D1

6 ABOLITE EASTPORT LUMINAIRE ORDERING INFORMATION TYPICAL ORDER EXAMPLE: Luminaire Prefix EPT Mounting S-Surface P-Pendant W-Wall EPT P 150 MH 120 GWT LDS96 FG Rated Wattage /32/ /32/ FOOTNOTES: 1- Uses the SMB less ballast. 2- Available pre-wired with surface mount only. Line Light Source Voltage Finish Wiring Options INC 1 -Incandescent CFL - Single Compact Fluorescent EMH - Electronic Metal Halide 2 INC -Incandescent CFL - Single Compact Fluorescent MH - Metal Halide PSMV - Pulse-Start Metal Halide UE 347 UE UE MSV-Metallic Silver GWT-Gloss White GBK-Gloss Black GRD-Gloss Red GGN-Gloss Green GPT-Textured Graphite RUS-Textured Rust SVG-Satin Verde Green SCP - Satin Copper STQ - Satin Turquoise 3- If 347 is required, the WTRB or RB2 Remote Ballast is required. 4- Consult factory for other light sources available for export. LDS96-8' prewired leads (P)(Wall comes with 36" Leads Standard) DIM-Dimming Ballast FG-Frosted Globe BLG-Blue Globe GNG-Green Globe RDG-Red Globe YLG-Yellow Globe FG-Frosted Globe BLG-Blue Globe GNG-Green Globe RDG-Red Globe YLG-Yellow Globe USER INSTALLED ACCESSORIES (Accessories are finished in gloss white powder, other optional colors are available. Perf Baffles are Natural Aluminum Mill only.) Remote Ballasts + CRB 26/32/42 CFL UE GWT - Wall Mounted CFL Remote Ballast for use with Contemporary Brackets only CRB 50, 70, 100, 150 EMH UE GWT - Wall Mounted EMH Remote Ballast for use with Contemporary Brackets only PB 26/32/42 CFL UE GWT - Pole Mounted CFL Postline Remote Ballast Contemporary Wall Brackets CWBM 1 GWT 20 tall x 14 deep Medium Contemporary Wall Mount Stem and Bracket; Gloss White CWBL 1 GWT 23 tall x 20 deep Large Contemporary Wall Mount Stem and Bracket; Gloss White Note: Order Pendant Mount Fixture and CRB separately SMB 26/32/42 CFL UE GWT - Surface Mounted CFL Remote Ballast with swivel for Pendant Mounting SMB2 50, 70, 100, 150 EMH UE GWT- Surface Mounted EMH Remote Ballast with swivel for Pendant Mounting WMB 26/32/42 CFL UE GWT - Wall Mounted CFL Remote Ballast WMB2 50, 70, 100, 150 EMH UE GWT - Wall Mounted EMH Remote WTRB 175 PSMV MT WHT Weather-tight Remote Ballast RB2 175 PSMV MT Indoor Remote Ballast + Other Remote Ballasts (WTRB or RB2) are available. Straight Wall Brackets SWB 3 3 GWT - 3/4" x 3" (19mm x 76mm) Stem & Wall Plate SWB 6 3 GWT - 3/4" x 6" (19mm x 152mm) Stem & Wall Plate SWB 12 3 GWT - 3/4" x 12" (19mm x.4mm) Stem & Wall Plate SWB 18 3 GWT - 3/4" x 18" (19mm x.5mm) Stem & Wall Plate SWB 24 3 GWT - 3/4" x 24" (19mm x.6mm) Stem & Wall Plate Note: Designed for mounting over recessed 4" (102mm) Octagon box (box by other). Conduit Stems ST 12 3 GWT - 3/4" x 12" Conduit Stem ST 36 3 GWT - 3/4" x 36" Conduit Stem Perf Baffles (Surface and Wall Mounting Only) ST 18 3 GWT - 3/4" x 18" Conduit Stem ST 48 3 GWT - 3/4" x 48" Conduit Stem PR4E - Perforated metal ring diffuses and shields lamp image ST 24 3 GWT - 3/4" x 24" Conduit Stem PR4E Half perforated metal ring provides a wall wash behind fixture Natural aluminum Clevis Wall Mount Arm Brackets CMA 3 12 GWT - 12" (305mm) Clevis Bracket for Wall Mount Style CMA 3 18 GWT - 18" (457mm) Clevis Bracket for Wall Mount Style Note: Assembly includes Clevis, 3/4" Stem and CA5 Wall Plate. Fixture and WMB/WMB2 extra, order separately. LSI OUTDOOR LIGHTING BUILDING & WALL MOUNT Clevis Arm Bracket and WMB Balllast SWB 6 Bracket CWB Bracket CRB 26//32/42 CFL Remote Ballast For Wet Locations 03/16/ LSI INDUSTRIES INC. Project Name Catalog # Fixture Type Catalog No: EPT-S-26-CFL-UE-MSV-FG Lamp Type: (1) PL-T26W/830/4P/ALTO The Lighting Practice Date: 07/01/2009 Fixture Type: D1

7 Linear wall luminaires unshielded Housing: Die-cast aluminum top and bottom connected to an extruded aluminum body. Provided with a flat mounting plate for direct attachment to the wall over a single gang vertical switch box. Requires free space of minimum 18" above luminaire for relamping Electrical: Lampholder; 2G11, 4 pin rated 75 W, 600 V. Ballasts are electronic universal voltage 120 V through 277 V. Finish: Available in five standard BEGA colors: Black (BLK); White (WHT); Bronze (BRZ); Silver (SLV); Eurocoat (URO). To specify, add appropriate suffix to catalog number. Custom colors supplied on special order. U.L. listed, suitable for wet locations. Protection class: IP 44. Type: BEGA Product: Project: Voltage: Color: Options: Modified: B A C Wall luminaire Lamp Lumen A B C 4530 P 1 39 W CF twin-4p BEGA-US 1000 BEGA Way, Carpinteria, CA (805) FAX (805) copyright BEGA-US 2008 Updated 2/08 Catalog No: 4530P-SLV Date: 07/02/2009 Lamp Type: (1) PL-L40W/830/4P/RS/IS The Lighting Practice Fixture Type: F1

8 Linear wall luminaires unshielded Housing: Die-cast aluminum top and bottom connected to an extruded aluminum body. Provided with a flat mounting plate for direct attachment to the wall over a single gang vertical switch box. Requires free space of minimum 14" above luminaire for relamping. Electrical: Lampholder; 2G11, 4 pin rated 75 W, 600 V. Ballasts are electronic universal voltage 120 V through 277 V. Finish: Available in five standard BEGA colors: Black (BLK); White (WHT); Bronze (BRZ); Silver (SLV); Eurocoat (URO). To specify, add appropriate suffix to catalog number. Custom colors supplied on special order. U.L. listed, suitable for wet locations. Protection class: IP 44. Type: BEGA Product: Project: Voltage: Color: Options: Modified: B A C Wall luminaire Lamp Lumen A B C 4520 P 1 27 W CF twin-4p BEGA-US 1000 BEGA Way, Carpinteria, CA (805) FAX (805) copyright BEGA-US 2008 Updated 2/08 Catalog No: 4520P-SLV Date: 07/02/2009 Lamp Type: (1) PL-L24W/830/4P The Lighting Practice Fixture Type: F2

9 2 Catalog No: DU2-9-T8-P-10-0-(VOLT)-T-0 Date: 07/01/2009 Lamp Type: (1) CDM35/T6/830 The Lighting Practice Fixture Type: F3

10 Catalog No: DU2-9-T8-P-10-0-(VOLT)-T-0 Date: 07/01/2009 Lamp Type: (1) CDM35/T6/830 The Lighting Practice Fixture Type: F3

11 5305-WL CHEFREN How to Specify: 5304-WL ALBEDO EXAMPLE: 5305-WL-18 - MH39-120V - OA - LBPS - RMB - STD CATALOG NUMBER LAMPING OPTION VOLTAGE LENS OPTION FINISH BALLAST (HID ONLY) SPECIAL (STD OR MOD) TECHNICAL DATA: PRODUCT SPECIFICATIONS: Catalog#: 5304-WL or 5305-WL Lamping: 5304-WL-18 *I - (1) 60W HALOGENA/Med. & 5305-WL-18 F - (1) CFTR26W/GX24q-3 (Surface Mount) MH39-(1) 39W T-6/G12 MH50-(1) 50W ED-17/Med. (Recessed Mount) I/RW- (1) 75W HALOGENA/Med. F/RW- (1) CFTR26W/GX24q-3 MH39/RW - (1) 39W T-6/G12 MH50/RW - (1) 50W ED-17/Med WL-24 *I - (1) 75W HALOGENA/Med. & 5305-WL-24 F - (1) CFTR42W/GX24q-4 (Surface Mount) MH100-(1) 100W ED-17/Med. (Recessed Mount) I/RW- (1) 75W HALOGENA/Med. F/RW- (1) CFTR42W/GX24q-4 MH100/RW - (1) 100W ED-17/Med. * HALOGENA is a product of Philips Lighting Company Voltage: 120V or 277V, Incandescent 120 Volt Only Lens Options: OA: Opal Acrylic (Etched) (Does not apply FAH: Hand Painted Faux Alabaster to fixture 5304) FAH4: White Vein FAH5: Antique Alabaster (Beige) FAH6: Gray Vein FAH7: Beige Vein FGH: Faux Glass Finishes: Standard GLV: Galvanized Paint LBPS: Light Bronze Paint Smooth PEW: Pewter Paint SGB: Semi-Gloss Black Paint VCP: Verdi Copper Patina Paint Custom CPF: Custom Paint Finish (Consult Factory) CMF: Custom Metal Finish (Consult Factory) Ballast: (HID only) IMB: Integral Electronic RMB: Remote Mount Magnetic Special: STD: Standard MOD: Modified Standard Weight: 5304-WL-18 RANGE: 11lbs. to 13lbs WL-18 RANGE: 11lbs. to 13lbs WL-24 RANGE: 14lbs. to 16lbs WL-24 RANGE: 14lbs. to 16lbs. EXTERIORS WL-18 OR 5305-WL-18 12" 18" WL-24 OR 5305-WL /8" 24" SURFACE MOUNT 18" 24" 5304-WL-18 OR 5305-WL-18 RECESSED MOUNT 16-1/2" 5-9/16" 10-1/4" 18" WL-24 OR 5305-WL /8" 5-9/16" 12-1/2" 24" " 24" ** Recessed Mount: Rough in Diameter Opening 3760 West Fourth Street Winona, MN Fax Catalog No: 5305-WL-18-MH39/RW-(VOLT)-OA-GLV-IMB-STD Date: 07/10/2009 Lamp Type: (1) CDM35/T6/830 The Lighting Practice Fixture Type: F4

12 COMMERCIAL & ARCHITECTURAL LIGHTING 4" HID-MH SERIES OPEN REFLECTOR/BAFFLE 50W MAX (PAR-20/30 OR ED17) 4MH SERIES FIXTURE SPECIFICATIONS SIDE VIEW FIXTURE SP4MH LAMP PAR-20 WATTS 39 BALLAST EX - 120/ mm ED17-50 watt only 50 TOP VIEW mm mm mm TRIM NO: 4410 TRIM SPECIFICATIONS FINISH: CL- Clear Alzak, Low Iridescence WE- Wheat Alzak GO- Gold Alzak UM- Umber Alzak PW- Pewter Alzak BL- Black Finish WH- White Finish TRIM OPTIONS SG- Soft Glow Finish-add SG to color number PF- Polished Flange BF- Black Flange BB- Black Micro Baffle WB- White Micro Baffle mm TYPICAL ORDER Line item 1 (FRAME): SP4MH35EX Line Item 2 (TRIM): 4410 CL BB PRODUCT INFORMATION: Fixture designed for open rated lamps. Heavy gauge spun aluminum reflector with white flange. #20 Gauge galvanized frame, easy to install. 12" bar hangers expandable to 24". Junction box pre-wired, grounded, listed for through branch circuit wiring. Extruded aluminum socket housing dissipates heat. Electronic ballast standard up to 50 Watts, serviceable from below ceiling. True 120/277 volt operation. Electronic ballast with low operating temperature extends lamp life. Suitable for use in damp location. Manufactured and tested to UL standard No. 1598/ETL Listed. FRAME OPTIONS RM - Remodeler (Cut Away). FS - Fusing QRS - Quartz re-strike BH27-27" Mounting Bars (2 Per Set). PR - Plaster Ring (consult factory). FIXTURE NO. FRAME-IN-KIT NO. FIXTURE TYPE SUBMITTAL WORKSHEET TRIM OPTIONS GS - Gasket (For Reflector) Jefferson Street Fall River, MA TEL: FAX: Catalog No: SP4MH-39PAR20-EX-4410-CLSGPF Date: 07/28/2009 Lamp Type: (1)CDM35/PAR20/M/FL/3K/ALTO The Lighting Practice Fixture Type: K1

13 Everest Series TM The Everest Series utilizes the popular Master Color PAR20 metal halide lamp. The Master Color lamp provides long life, high lumen output and great color. The Everest Series will provide years of trouble free performance. Available in three different cutoff configurations and when combined with the many optical, accessory and ballast options, the Everest Series is unmatched in metal halide lighting performance. The Everest Series uses B-K Lighting s exclusive 360SL Mounting System which incorporates the Posilock Knuckle. This allows for horizontal and rotational aiming without removing the ballast cover and will ensure the integrity of the aiming position. Features Tamper proof design. Completely sealed optical compartment. Clear, tempered glass lens, factory sealed. Machined aluminum construction with stainless steel hardware. 360SL Mounting System allows vertical to horizontal and rotational aiming with Posilock feature, provides integral wireway. Medium base, pulse rated lamp holder with 250 C, 18 ga., wire leads Listed with 35W PAR20 metal halide lamps. For use with 35W, 120V or 277V metal halide ballast. For ballast information, see page B-K LIGHTING Catalog No: EV-58-SAP-13-B-PC35-(VOLT) Date: 07/01/2009 Lamp Type: (1) CDM35/PAR20/M/SP/3K/ALTO The Lighting Practice Fixture Type: L1

14 HP Metal Halide Ballast Product Update See Precision 2 Brochure Everest Series TM Ballast Options RM Metal Halide Ballast HP Remote Metal Halide Product Update See Precision 2 Brochure TSB Metal Halide Ballast PPII Metal Halide Ballast TMB Metal Halide Ballast PC Metal Halide Ballast For ballast electrical data and remote ballast wiring distances, see page 127. B-K LIGHTING 23 Catalog No: EV-58-SAP-13-B-PC35-(VOLT) Date: 07/01/2009 Lamp Type: (1) CDM35/PAR20/M/SP/3K/ALTO The Lighting Practice Fixture Type: L1

15 Notes: Job: Type: 100 LINE 101 PERFORMANCE SCONCE GENERAL DESCRIPTION: The Gardco 101 Trapezoidal Wedge high performance sconce offers an excellent alternative to unsightly wall mounted fixtures. These architecturally refined luminaires are designed to integrate naturally to wall surfaces. The 101 luminaires are available with three (3) different distribution patterns - a wide throw, a medium throw and a forward throw. Each luminaire is designed to accept HID sources up to 175MH, and Compact Fluorescent up to (2) 42W. Housings are sealed throughout, completely excluding moisture, dust, insects and contaminants. CUTOFF PERFORMANCE: 101 luminaires installed in the normal downlight position, with a flat glass lens, provide full cutoff performance. ORDERING PREFIX DISTRIBUTION WATTAGE VOLTAGE FINISH OPTIONS 101EMC MT 226QF NP SL Enter the order code into the appropriate box above. Note: Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. PREFIX DISTRIBUTION 101 Trapezoidal Wedge below for Refer to confiiguration chart FT Forward Throw Not Available with Fluorescent or LPS sources. 101EM Emergency Sconce available combinations. WT Wide Throw Not Available with Fluorescent or LPS sources. 101EMC Emergency Sconce Cold Temperature 101EMR Remote Emergency Sconce MT Medium Throw WATTAGE AND VOLTAGE LAMP / VOLTAGE CHART Combinations marked with a dot or shown with UNIV are available CONFIGURATION CHART - 101EM OR 101EMC 5 Voltage for ordering. Distribution Voltage HID* MH 70MH 100MH 150MH 175MH** 50CMHE 1 UNIV 70CMHE 1 UNIV 100CMHE 1 UNIV 35HPS 50HPS 70HPS 100HPS 150HPS 18LPS Fluorescent 26QF 1 UNIV 226QF 1 UNIV 32TRF 1 UNIV 232TRF 1 UNIV 42TRF 1 UNIV 242TRF 1 UNIV FINISH OPTIONS MH - Metal Halide CMHE - Ceramic Metal Halide with Electronic Ballast HPS - High Pressure Sodium LPS - Low Pressure Sodium TRF - Triple Tube Fluorescent QF - Quad Fluorescent * MH, CMHE and HPS types require medium based E17 lamps. All MH 150W and below are pulse start by design, including CMHE types. ** 175MH not available for sale in the United States. Fluorescent FT WT MT QF 2 32TRF 42TRF CONFIGURATION CHART - 101EMR 5 Distribution Voltage Fluorescent FT WT MT QF 2,3,4 32TRF 232TRF 2,3,4 42TRF 242TRF 2,4 1. Fluorescent and CMHE luminaires feature electronic ballasts that accept 120V through 277V, 50hz to 60hz, input. Specify UNIV voltage for 120V through 277V. 2. One (1) lamp is powered in emergency mode with EM, EMC and EMR types with the B84CG option. 3. Available with ICE420 option, which powers two (2) lamps in emergency mode. ICE420 option only available with 226QF or 232TRF. CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 4. Available with I162 option, which powers two (2) lamps in emergency mode. Lamps are wired in parallel. In emergency mode, should one lamp become inoperable, the remaining lamp will operate with a minimum total initial output of 2,250 lumens. 5. Refer to 101 Emergency Sconce Table on page 2 for additional information. BRP Bronze Paint F 6 Fusing EMR Luminaires Only: 15 BLP Black Paint PCB 7 Button Type Photocontrol B84CG Bodine Remote Emergency Pack WP White Paint QS 8 Quartz Standby ICE IOTA Remote Emergency Pack 226QF / 232TRF only. NP Natural Aluminum Paint QST 8 Quartz Standby - Timed Delay I IOTA Remote Emergency Pack 226QF / 232TRF / 242TRF only. BGP Beige Paint Q924 9 Quartz Emergency OC Optional Color Paint Q12V 9 Quartz 12V Emergency V through 277V only 15. All Emergency Battery Packs for EMR types MUST be ordered Specify Optional Color or RAL Q20MR 10 (2)MR16 12V Emergency - 20 Watt 7. Not available with 480V. with luminaires and supplied by Gardco. ex: OC-LGP or OC-RAL7024. Q35MR 10 (2)MR16 12V Emergency - 35 Watt 8. HID only, Not available with CMHE Ballasts, FT Optics or in 16. CAUTION: Maximum battery pack input power for EMR units SL Solite 480V. 100w Quartz maximum. with ICE420 option is 100 watts (.83 amps) when heating element SC Special Color Paint Diffusing Lens 9. WT Optic only. 150w HID maximum, 100w Quartz maximum. is on. This is in addition to the normal input power for luminaire Specify. Must supply color chip. UT 5 Uptilt 10. WT Optic only. 50CMHE or 70CMHE only. Supplied with two lamps and ballast. WLU 11 (2) 20W MR16 or two (2) 35W MR16 Flood (40 beam) lamps. 17. Lamps are wired in parallel. In emergency mode, should one lamp Wet Location Door for Inverted Mount 11. Not available with WG or POLY options. become inoperable, the remaining lamp will operate with a WS 12 Wall Mounted Box for Surface Conduit 12. Rear entry permitted. minimum total initial output of 2,250 lumens. WS/UT 12 WS Option w/5 Uptilt 13. Not Available with WLU option watt HID maximum. Polycarbonate lenses carry a WG 13 Wire Guard 1 year warranty only. POLY 13,14 Polycarbonate Sag Lens Philips Gardco 1611 Clovis Barker Road San Marcos, TX (800) (512) FAX: (512) Copyright 2009 Philips Group. All Rights Reserved. International Copyright Secured. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program /0509 Catalog No: 101EMC-MT-226QF-(VOLT)-NP-SL Date: 07/01/2009 Lamp Type: (2) PL-C26W/830/4P/ALTO The Lighting Practice Fixture Type: M1

16 SPECIFICATIONS GENERAL: Each Gardco 101 luminaire is a wall mounted cutoff luminaire for high intensity discharge or compact fluorescent lamps. Internal components are totally enclosed in a rain-tight, dust-tight and corrosion resistant housing. The housing, back plate and door frame are die cast aluminum. A choice of three (3) optical systems is available. Luminaires are suitable for wet locations (damp locations if inverted). HOUSING: Housings are die cast aluminum. A memory retentive gasket seals the housing to the door frame to exclude moisture, dust, insects and pollutants from the optical system. A black, die cast ribbed backplate dissipates heat for longer lamp and ballast life. DOOR FRAME: A single-piece die cast aluminum door frame integrates to the housing form. The door frame is hinged closed and secured to the housing with two (2) captive stainless steel fasteners. The heat and impact resistant 1/8 (.32cm) tempered glass lens and one-piece gasket are mechanically secured to the door frame with four (4) galvanized steel retainers. OPTICAL SYSTEMS: Reflectors are composed of specular extruded and faceted components, electropolished, anodized and sealed. Reflector segments are set in arc tube image duplicating patterns to achieve the wide throw, forward throw or medium throw downlight distributions. ELECTRICAL: 100 LINE 101 PERFORMANCE SCONCE STANDARD LUMINAIRES: Each high power factor HID core and coil ballast is the separate component type. All HID ballasts are capable of providing reliable lamp starting down to -20 F/-29 C. Standard fluorescent units have a starting temperature of 0 F/-18 C. Standard fluorescent ballasts are high power factor electronic solid state. Component-tocomponent wiring within the luminaire will carry no more than 80% of rated current and is listed by UL for use at 600 VAC at 150 C or higher. Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. LUMINAIRES with Q924 / G12V /QMR20 / QMR35 OPTIONS: Luminaires with the Q924 option require a separate source of 120V power (by others.) Luminaires with Q12V, Q20MR or Q35MR options require a separate source of 12V power (by others.) EMERGENCY LUMINAIRES: All emergency luminaires feature an indicator light visible through the lens and a test switch accessible through the door assembly. Minimum battery pack ambient temperatures are as indicated in the 101 Emergency Sconce Table. In the event of a power interruption, emergency luminaires will power compact fluorescent lamps as indicated in the 101 Emergency Sconce Table at reduced light levels for a minimum of 90 minutes. EMR LUMINAIRES include a 7.5 /2.29m, 12 wire, quick disconnect assembly for wiring through conduit (by others) to a B84CG, I162 or ICE420 fluorescent emergency battery pack. The fluorescent emergency battery pack MUST be supplied by Gardco. The B84CG option, the I162 option or the ICE420 option required on the order to the factory. DIMENSIONS 7" cm CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 101 Emergency Sconce Table Emergency Luminaire Battery Pack Min. Ambient Temperature 101EM (Integral) 32 F / 0 C 101EMC (Integral) 101EMR (Remote) with B84CG Option LAMPHOLDER: Pulse rated medium base sockets are glazed porcelain with nickel plated screw shell. Fluorescent sockets are high temperature (PBT) with brass contacts. FINISH: Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors are as listed. Consult factory for specs on custom colors. LABELS: All luminaires bear UL or CUL (where applicable) labels, except as noted. Lens down application is Wet Location and lens up is Damp Location. Emergency luminaires do not bear CUL label. WARRANTY: Gardco luminaires feature a 5 year limited warranty. See Warranty Information on for complete details and exclusions. Polycarbonate lenses carry a 1 year warranty only. FULL CUTOFF PERFORMANCE: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle of 90 above nadir. Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire. CUTOFF PERFORMANCE: Cutoff performance means a luminaire distribution where the candela per 1000 lamp lumens does not numerically exceed 25 (2.5 percent) at an angle at or above 90 above nadir, and 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire. Mounting Plate 4 5/16" cm 1 3/4" dia. 4.4 cm -4 F / -20 C 32 F/ 0 C 101EMR (Remote) with I162 Option F/ 0 C 101EMR (Remote) with ICE420 Option 20 0 F / -18 C 3" 7.62 cm Lamps Powered in Emergency Mode (1) 26, (1) 32, or (1) 42 Watt Compact Fluorescent Lamp (2) 26, (2) 32 or (2) 42 Watt Compact Fluorescent Lamps (2) 26, or (2) 32 Watt Compact Fluorescent Lamps Notes: 18. See Gardco Emergency Light Output Information ( ) for emergency lumen output data. 19. Lamps are wired in parallel. In emergency mode, should one lamp become inoperable, the remaining lamp will operate with a minimum total initial output of 2,250 lumens. 20 CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 16 1/4" cm 9" cm Mounting Bolt Pattern Note: Mounting plate center is located in the center of the luminaire width and 3.5"(8.89cm) above the luminaire bottom (lens down position). Splices must be made in the J-box (by others). Mounting plate must be secured by max. 5/16" (.79cm) diameter bolts (by others) structurally to the wall. Philips Gardco 1611 Clovis Barker Road San Marcos, TX (800) (512) FAX: (512) Copyright 2009 Philips Group. All Rights Reserved. International Copyright Secured. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program /0509 Catalog No: 101EMC-MT-226QF-(VOLT)-NP-SL Date: 07/01/2009 Lamp Type: (2) PL-C26W/830/4P/ALTO The Lighting Practice Fixture Type: M1

17 Notes: Job: Type: 100 LINE 101 PERFORMANCE SCONCE GENERAL DESCRIPTION: The Gardco 101 Trapezoidal Wedge high performance sconce offers an excellent alternative to unsightly wall mounted fixtures. These architecturally refined luminaires are designed to integrate naturally to wall surfaces. The 101 luminaires are available with three (3) different distribution patterns - a wide throw, a medium throw and a forward throw. Each luminaire is designed to accept HID sources up to 175MH, and Compact Fluorescent up to (2) 42W. Housings are sealed throughout, completely excluding moisture, dust, insects and contaminants. CUTOFF PERFORMANCE: 101 luminaires installed in the normal downlight position, with a flat glass lens, provide full cutoff performance. ORDERING PREFIX DISTRIBUTION WATTAGE VOLTAGE FINISH OPTIONS 101 FT 100MH NP SL Enter the order code into the appropriate box above. Note: Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. PREFIX DISTRIBUTION 101 Trapezoidal Wedge below for Refer to confiiguration chart FT Forward Throw Not Available with Fluorescent or LPS sources. 101EM Emergency Sconce available combinations. WT Wide Throw Not Available with Fluorescent or LPS sources. 101EMC Emergency Sconce Cold Temperature 101EMR Remote Emergency Sconce MT Medium Throw WATTAGE AND VOLTAGE LAMP / VOLTAGE CHART Combinations marked with a dot or shown with UNIV are available CONFIGURATION CHART - 101EM OR 101EMC 5 Voltage for ordering. Distribution Voltage HID* MH 70MH 100MH 150MH 175MH** 50CMHE 1 UNIV 70CMHE 1 UNIV 100CMHE 1 UNIV 35HPS 50HPS 70HPS 100HPS 150HPS 18LPS Fluorescent 26QF 1 UNIV 226QF 1 UNIV 32TRF 1 UNIV 232TRF 1 UNIV 42TRF 1 UNIV 242TRF 1 UNIV FINISH OPTIONS MH - Metal Halide CMHE - Ceramic Metal Halide with Electronic Ballast HPS - High Pressure Sodium LPS - Low Pressure Sodium TRF - Triple Tube Fluorescent QF - Quad Fluorescent * MH, CMHE and HPS types require medium based E17 lamps. All MH 150W and below are pulse start by design, including CMHE types. ** 175MH not available for sale in the United States. Fluorescent FT WT MT QF 2 32TRF 42TRF CONFIGURATION CHART - 101EMR 5 Distribution Voltage Fluorescent FT WT MT QF 2,3,4 32TRF 232TRF 2,3,4 42TRF 242TRF 2,4 1. Fluorescent and CMHE luminaires feature electronic ballasts that accept 120V through 277V, 50hz to 60hz, input. Specify UNIV voltage for 120V through 277V. 2. One (1) lamp is powered in emergency mode with EM, EMC and EMR types with the B84CG option. 3. Available with ICE420 option, which powers two (2) lamps in emergency mode. ICE420 option only available with 226QF or 232TRF. CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 4. Available with I162 option, which powers two (2) lamps in emergency mode. Lamps are wired in parallel. In emergency mode, should one lamp become inoperable, the remaining lamp will operate with a minimum total initial output of 2,250 lumens. 5. Refer to 101 Emergency Sconce Table on page 2 for additional information. BRP Bronze Paint F 6 Fusing EMR Luminaires Only: 15 BLP Black Paint PCB 7 Button Type Photocontrol B84CG Bodine Remote Emergency Pack WP White Paint QS 8 Quartz Standby ICE IOTA Remote Emergency Pack 226QF / 232TRF only. NP Natural Aluminum Paint QST 8 Quartz Standby - Timed Delay I IOTA Remote Emergency Pack 226QF / 232TRF / 242TRF only. BGP Beige Paint Q924 9 Quartz Emergency OC Optional Color Paint Q12V 9 Quartz 12V Emergency V through 277V only 15. All Emergency Battery Packs for EMR types MUST be ordered Specify Optional Color or RAL Q20MR 10 (2)MR16 12V Emergency - 20 Watt 7. Not available with 480V. with luminaires and supplied by Gardco. ex: OC-LGP or OC-RAL7024. Q35MR 10 (2)MR16 12V Emergency - 35 Watt 8. HID only, Not available with CMHE Ballasts, FT Optics or in 16. CAUTION: Maximum battery pack input power for EMR units SL Solite 480V. 100w Quartz maximum. with ICE420 option is 100 watts (.83 amps) when heating element SC Special Color Paint Diffusing Lens 9. WT Optic only. 150w HID maximum, 100w Quartz maximum. is on. This is in addition to the normal input power for luminaire Specify. Must supply color chip. UT 5 Uptilt 10. WT Optic only. 50CMHE or 70CMHE only. Supplied with two lamps and ballast. WLU 11 (2) 20W MR16 or two (2) 35W MR16 Flood (40 beam) lamps. 17. Lamps are wired in parallel. In emergency mode, should one lamp Wet Location Door for Inverted Mount 11. Not available with WG or POLY options. become inoperable, the remaining lamp will operate with a WS 12 Wall Mounted Box for Surface Conduit 12. Rear entry permitted. minimum total initial output of 2,250 lumens. WS/UT 12 WS Option w/5 Uptilt 13. Not Available with WLU option watt HID maximum. Polycarbonate lenses carry a WG 13 Wire Guard 1 year warranty only. POLY 13,14 Polycarbonate Sag Lens Philips Gardco 1611 Clovis Barker Road San Marcos, TX (800) (512) FAX: (512) Copyright 2009 Philips Group. All Rights Reserved. International Copyright Secured. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program /0509 Catalog No: 101-FT-100MH-(VOLT)-NP-SL Date: 07/01/2009 Lamp Type: (1) MHC100/U/M/3K/ALTO The Lighting Practice Fixture Type: M2

18 SPECIFICATIONS GENERAL: Each Gardco 101 luminaire is a wall mounted cutoff luminaire for high intensity discharge or compact fluorescent lamps. Internal components are totally enclosed in a rain-tight, dust-tight and corrosion resistant housing. The housing, back plate and door frame are die cast aluminum. A choice of three (3) optical systems is available. Luminaires are suitable for wet locations (damp locations if inverted). HOUSING: Housings are die cast aluminum. A memory retentive gasket seals the housing to the door frame to exclude moisture, dust, insects and pollutants from the optical system. A black, die cast ribbed backplate dissipates heat for longer lamp and ballast life. DOOR FRAME: A single-piece die cast aluminum door frame integrates to the housing form. The door frame is hinged closed and secured to the housing with two (2) captive stainless steel fasteners. The heat and impact resistant 1/8 (.32cm) tempered glass lens and one-piece gasket are mechanically secured to the door frame with four (4) galvanized steel retainers. OPTICAL SYSTEMS: Reflectors are composed of specular extruded and faceted components, electropolished, anodized and sealed. Reflector segments are set in arc tube image duplicating patterns to achieve the wide throw, forward throw or medium throw downlight distributions. ELECTRICAL: 100 LINE 101 PERFORMANCE SCONCE STANDARD LUMINAIRES: Each high power factor HID core and coil ballast is the separate component type. All HID ballasts are capable of providing reliable lamp starting down to -20 F/-29 C. Standard fluorescent units have a starting temperature of 0 F/-18 C. Standard fluorescent ballasts are high power factor electronic solid state. Component-tocomponent wiring within the luminaire will carry no more than 80% of rated current and is listed by UL for use at 600 VAC at 150 C or higher. Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. LUMINAIRES with Q924 / G12V /QMR20 / QMR35 OPTIONS: Luminaires with the Q924 option require a separate source of 120V power (by others.) Luminaires with Q12V, Q20MR or Q35MR options require a separate source of 12V power (by others.) EMERGENCY LUMINAIRES: All emergency luminaires feature an indicator light visible through the lens and a test switch accessible through the door assembly. Minimum battery pack ambient temperatures are as indicated in the 101 Emergency Sconce Table. In the event of a power interruption, emergency luminaires will power compact fluorescent lamps as indicated in the 101 Emergency Sconce Table at reduced light levels for a minimum of 90 minutes. EMR LUMINAIRES include a 7.5 /2.29m, 12 wire, quick disconnect assembly for wiring through conduit (by others) to a B84CG, I162 or ICE420 fluorescent emergency battery pack. The fluorescent emergency battery pack MUST be supplied by Gardco. The B84CG option, the I162 option or the ICE420 option required on the order to the factory. DIMENSIONS 7" cm CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 101 Emergency Sconce Table Emergency Luminaire Battery Pack Min. Ambient Temperature 101EM (Integral) 32 F / 0 C 101EMC (Integral) 101EMR (Remote) with B84CG Option LAMPHOLDER: Pulse rated medium base sockets are glazed porcelain with nickel plated screw shell. Fluorescent sockets are high temperature (PBT) with brass contacts. FINISH: Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors are as listed. Consult factory for specs on custom colors. LABELS: All luminaires bear UL or CUL (where applicable) labels, except as noted. Lens down application is Wet Location and lens up is Damp Location. Emergency luminaires do not bear CUL label. WARRANTY: Gardco luminaires feature a 5 year limited warranty. See Warranty Information on for complete details and exclusions. Polycarbonate lenses carry a 1 year warranty only. FULL CUTOFF PERFORMANCE: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle of 90 above nadir. Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire. CUTOFF PERFORMANCE: Cutoff performance means a luminaire distribution where the candela per 1000 lamp lumens does not numerically exceed 25 (2.5 percent) at an angle at or above 90 above nadir, and 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire. Mounting Plate 4 5/16" cm 1 3/4" dia. 4.4 cm -4 F / -20 C 32 F/ 0 C 101EMR (Remote) with I162 Option F/ 0 C 101EMR (Remote) with ICE420 Option 20 0 F / -18 C 3" 7.62 cm Lamps Powered in Emergency Mode (1) 26, (1) 32, or (1) 42 Watt Compact Fluorescent Lamp (2) 26, (2) 32 or (2) 42 Watt Compact Fluorescent Lamps (2) 26, or (2) 32 Watt Compact Fluorescent Lamps Notes: 18. See Gardco Emergency Light Output Information ( ) for emergency lumen output data. 19. Lamps are wired in parallel. In emergency mode, should one lamp become inoperable, the remaining lamp will operate with a minimum total initial output of 2,250 lumens. 20 CAUTION: Maximum battery pack input power for EMR units with ICE420 option is 100 watts (.83 amps) when heating element is on. This is in addition to the normal input power for luminaire lamps and ballast. 16 1/4" cm 9" cm Mounting Bolt Pattern Note: Mounting plate center is located in the center of the luminaire width and 3.5"(8.89cm) above the luminaire bottom (lens down position). Splices must be made in the J-box (by others). Mounting plate must be secured by max. 5/16" (.79cm) diameter bolts (by others) structurally to the wall. Philips Gardco 1611 Clovis Barker Road San Marcos, TX (800) (512) FAX: (512) Copyright 2009 Philips Group. All Rights Reserved. International Copyright Secured. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program /0509 Catalog No: 101-FT-100MH-(VOLT)-NP-SL Date: 07/01/2009 Lamp Type: (1) MHC100/U/M/3K/ALTO The Lighting Practice Fixture Type: M2

19 DERO Bike Hitch High security Great for sidewalk placement One unit parks two bikes The Bike Hitch is an attractive and space efficient bike rack. The Bike Hitch was specifically designed for sidewalks and other narrow space applications. The rack s design restricts bikes to parking parallel with the rack so bikes won t protrude out into the sidewalk or street. Your Logo Here! We can include your organization s logo in the center of a specially designed Bike Hitch. Contact us for more details on this unique option Printed on recycled paper

20 B i k e H i t c h Specifications and Space Use 16.5" Product Capacity Dero Bike Hitch As manufactured by Dero Bike Racks 2 Bikes 35" 1.5" Materials Centerbeam: 2 schedule 40 pipe (2.375 OD) Ring: 1.5 OD 11 gauge tube 2.375" Finishes An after fabrication hot dipped galvanized finish is standard. 250 TGIC powder coat colors, a thermoplastic coating and a stainless steel option are also available. 75" Our powder coat finish assures a high level of adhesion and durability by following these steps: 1. Sandblast 2. Iron phosphate pretreatment 3. Epoxy primer electrostatically applied 4. Final thick TGIC polyester powder coat Stainless Steel: 304 grade stainless steel material finished in either a high polished shine or a satin finish. A rubbery PVC Dip is also available 32" Installation Methods In-ground mount is embedded into concrete base. Surface mount has one 5 x 6 foot which is anchored to the ground with four anchors (included with rack). WALL WALL Space Use and Setbacks Wall Setbacks: For racks set parallel to a wall: Minimum: 12 Recommended: 24 For racks set perpendicular to a wall: Minimum 35 (centerline measurement) Recommended: 38 (54 if aisle is needed between bike and wall) STREET 24" 76" 36" 54" (36 if no aisle needed) STREET Distance Between Racks: Minimum: 24 Recommended: 38 Street Setbacks: Minimum:

21 B i k e H i t c h Installation Instructions - Surface Mount Tools Needed for Installation Tape Measure Marker or Pencil Masonry Drill Bit Drill (Hammer drill recommended) Hammer Wrench 9/16 Level Washers (for leveling if necessary) Recommended Base Materials: Solid concrete is the best base material for installation. Ask your Dero Rack representative which anchor is appropriate for your application to ensure the proper anchors are shipped with your rack. Be sure nothing is underneath the base material that could be damaged by drilling. Installation: 3/8 anchors are shipped with the rack. Place the rack in the desired location. Use a marker or pencil to outline the holes of the flange onto the base material. Drill the holes in accordance with the specifications shipped with the anchors. Make sure the holes are at least 6 away from any cracks in the base material. Concrete Spike 1 2 Mark holes 3 4 Use washers to level rack Wedge Anchor Drill hole 3 Deep Tamper Resistant Fasteners (Anchors will vary according to install surface) The concrete spike is a permanent anchor. The top of the wedge anchor can also be pounded sideways after installation so that it cannot be removed. Other tamper resistant fasteners are also available for purchase. When using the special tamper resistant nuts, always set and first tighten the anchors. Once the rack is installed, replace two nuts from the bracket (opposite sides from each other) with the tamper resistant fastener. DO NOT OVERTIGHTEN the tamper resistant nut. Breakaway Nut Spanner Nut Triple-slot Nut If you have any questions about installation or other features of the Bike Bike Rack, please call us toll free at Concrete Spike

22 B i k e H i t c h In-ground Installation Instructions Tools needed for installation Level Cement mixing tub Shovel Trowel Installing into Existing Sidewalk Hole coring machine with 4 bit Access to water hose Materials to build brace (see Install Tip at bottom of page) Core holes no less than 3 diameter (4 recommended) and no less than 6 deep into sidewalk. Place Bike Hitch into hole making sure the rack is level. Fill hole with Por-Rok or epoxy grout of the Bike Hitch should remain above the surface. Make sure Hitch is level and held in place until the grout has completely set Recommended hole diameter = 4 Installing Into a New Sidewalk: Stake Method: Rack Foot Final grade level Sleeve Method: Final grade level Use rack to measure exact location in pour bed. Pound stake into pour bed where end of rack will sit. Slide rack end onto stake. You may need to dig the end of the rack into the sand to make sure the rack sits at least 35 above final grade level. The stake keeps the rack straight while the concrete is being poured. Make sure the rack is level and true. Pour concrete around the rack. Make sure the rack is not touched until the concrete has completely set. Poured concrete (4-7 deep) Sand pour bed Place corrosion resistant sleeve (min. 3 inside diameter) in sand pour bed in exact location where rack will be installed. Make sure top of sleeve is at same level as desired finished concrete surface. Fill sleeve with sand to keep it in place and prevent it from filling with concrete. Pour concrete and allow to cure. After appropriate cure time, dig out sand from sleeves and insert racks, making sure they are level and at the appropriate height. Pour in Por-Rok or epoxy grout and allow to set. Sand pour bed Poured concrete (4-7 deep) INSTALL TIP An easy way to brace the Bike Hitch while the grout sets is to bolt two 1x4 boards together at one end and clamp them onto the legs of the Bike Hitch like a clothes pin. Note: Sleeve should have profile to keep it from coming loose from hardened concrete ID

23

24

25

26

27

28

29

30

31 Proposed Retail Development at 7017 Mineral Point Road Acres Zone: C3L Out Parcel of the Greater West Towne development Initial/Final Approval Presentation to the Urban Design Commission August 5, 2009 On behalf of CBL & Associates Properties, it is ka Incorporated s pleasure to present to the Urban Design Commission of the City of Madison our design for a proposed 6,000 square foot retail development. Located on the site of the existing West Towne Mall, the property sits at the prominent corner of Mineral Point Road and Gammon Road. The building will be comprised of an up-and-coming restaurant tenant and retail space for one or two future tenants. SmashBurger, a sleek, fast casual restaurant named for the unique way they prepare their grilled sandwiches, will bring their novel dining concept to the north side of the development in a 2,000 s.f. space, with an outdoor dining patio facing Mineral Point Road. The remaining 4,000 s.f. will be developed as a shell building that will provide attractive, yet flexible lease space for its future occupants. The proposed building will enjoy high visibility from multiple directions. Traffic generated from U.S. 12/14 to the south, existing shopping and dining at West Towne Mall, and the upcoming arrival of a Longhorn Steakhouse on the same parcel make the site highly leasable and ideal for development. The intent of the design was to create a building that would not only meet the needs of modern retail tenants, but also serve as a feature piece for the Greater West Towne area. Location Map (Not to Scale) 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. Location Map and Narrative 7017 Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC August 5, 2009 ka#

32 SITE DATA: SITE ZONING: SITE AREA: FLOOR AREA: F.A.R.: BUILDING HEIGHT: PARKING: BIKE PARKING: LOADING SPACES: TREE ISLANDS: (COMMERCIAL SERVICE DISTRIBUTION DISTRICT) C3L Ac. (110,163 SF) 4,000 sf RETAIL 2,000 sf SMASHBURGER 5,695 sf LONGHORN (RESTAURANT) 11,695 sf TOTAL.1069 (<3.0) (11,695 SF / 110,163 SF) 25 FEET (3 STORY / 40 FEET MAX.) 14 SPACES RETAIL (4,000 SF 1/300 SF) 33 SPACES 83 SPACES 130 SPACES TOTAL REQ D 141 PROVIDED (2 ACCESSIBLE) 16 SPACES PROVIDED 1 10 x35 SPACE REQUIRED 1866 sf REQUIRED 3649 sf PROVIDED (RESTAURANT) SMASHBURGER (72 INDOOR % SEATING CAP.) LONGHORN (276 30% SEATING CAPACITY) (3% OF 62,172 SF) (5,000 TO 10,000 GROSS SF) (See enlarged site plan, sheet UDC-3) 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. Overall Site Plan and Data 7017 Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-1 August 5, 2009 ka#

33 West Towne Mall Olive Garden Office use across Mineral Point Rd. Existing Site Existing Site Existing pedestrian connection Looking west down Mineral Point Road Looking north from Gammon Road 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. Contextual Site Information and Existing Site Photos Future Longhorn Existing Smokey Bones (to be demolished) 7017 Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-2 August 5, 2009 ka#

34 LEASE PARCEL LINE 7 7 LANDSCAPE AREA (TYP.) PEDESTRIAN CONNECTION R=10 5 BIKE PARKING 4 2 x6 SPACES WITH ONE HITCH-STYLE RACK PER SPACE RETAIL 4,000 SF SHARED WASTE / RECYCLING AREA TRANSFORMER AND LANDSCAPE SCREENING LOADING SPACE SMASHBURGER 2,000 SF R=10 10 ELECTRICAL EASEMENT BIKE PARKING 6 2 x6 SPACES WITH ONE HITCH-STYLE RACK PER SPACE LEASE PARCEL LINE 7 OUTDOOR DINING - SCORED CONCRETE PATIO LANDSCAPE AREA (TYP.) BIKE PARKING 3 2 x6 SPACES WITH ONE HITCH-STYLE RACK PER SPACE R=8 R=8 LANDSCAPE AREA W/BOULDERS FOR TRAFFIC CONTROL 41 PEDESTRIAN CONNECTION BIKE PARKING 3 2 x6 SPACES WITH ONE HITCH-STYLE RACK PER SPACE LANDSCAPE AREAS W/BOULDERS FOR TRAFFIC CONTROL EXISTING AND PROPOSED PLANTING (SEE SHEET LP-1) PEDESTRIAN CONNECTION 7 ACCESSIBLE PARKING 8 STEPS 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. Enlarged Site Plan 7017 Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-3 August 5, 2009 ka#

35 Signage by tenant, typ. Signage by tenant, typ. ELEV T/O STUD Metal panel Flat glavanized metal panel Signage by tenant, typ. Corrugated galvanized metal panel Brick ELEV T/O STUD ELEV T/O STUD L1 L1 ELEV T/O STUD F4 F4 D1 D1 D1 D1 Metal panel ELEV T/O STOREFRONT Brick Cast stone water table/accent bands Split/ground face base F2 F2 F1 F1 F3 F3 Aluminum storefront system, typ. Split/ground face base Fenced outdoor seating area by tenant ELEV T/O SIDEWALK Piers detailed to be removable for tenant flexibility Open/closed metal canopies ELEV T/O SIDEWALK East Elevation Signage by tenant, typ. Metal panel ELEV T/O STUD ELEV T/O STUD ELEV T/O STUD Brick D1 D1 D1 D1 D1 D1 Corrugated galvanized metal panel ELEV T/O STOREFRONT Flat galvanized metal panel Aluminum storefront system, typ. F3 F3 M1 Cast stone water table/accent bands Split/ground face base ELEV T/O SIDEWALK Fenced outdoor seating area by tenant Open metal canopies North Elevation All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. 3/32 = Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-4 August 5, 2009 ka#

36 Signage by tenant, typ. Metal panel ELEV T/O STUD ELEV T/O STUD ELEV T/O STUD Brick D1 D1 D1 Corrugated galvanized metal panel Flat galvanized metal panel Metal panel L1 Corrugated galvanized metal panel L1 Signage by tenant, typ. ELEV T/O STUD Cast stone water table/accent bands M2 Brick Split/ground face base M1 M1 M1 F2 Cast stone water table/accent bands Fenced outdoor seating area by tenant Shared waste/recycling area Split/ground face base ELEV T/O SIDEWALK Open metal canopies Painted hollow metal doors, typ. Brick ELEV T/O SIDEWALK West Elevation Flat galvanized metal panel Corrugated galvanized metal panel Signage by tenant, typ. ELEV T/O STUD Metal panel L1 L1 ELEV T/O STUD ELEV T/O STOREFRONT Brick Note: Signage depicted in anticipated locations. Actual signage to be submitted later as separate permit. Landlord signage requirements for the center: signage to be individual letters which are internally illuminated, letters not to exceed 4' in height with total length not exceeding the lesser of 40% of the facade or 30' F2 Aluminum storefront system, typ. F2 F2 F2 Open/closed metal canopies Cast stone water table/accent bands Split/ground face base ELEV T/O SIDEWALK South Elevation All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. 3/32 = Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-5 August 5, 2009 ka#

37 Northeast Perspective North Perspective Northwest Perspective Southwest Perspective 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-6 August 5, 2009 ka#

38 Alucobond - Russet Mica (metal panels) Belden Brick Company Brown (field brick) Belden Brick Company Dark (field brick) Alucobond - Roasted Red Pepper (metal panels) Reading Rock Rockcast - Marigold GP-C (watertable & accents) Akron Brick and Block - Dark Burnt Umber (split face base) Reading Rock Rockcast - Crystal White GP-A (watertable & accents) Berridge Metals - satin finish galvalume (corrugated metal panels) Akron Brick and Block - Seashell (split face base) Berridge Metals - preweathered galvalume (flat metal panels) 2009 All ideas, arrangements, and plans indicated or represented by the above drawings are property of ka inc. and were created for the sole use in connection with the specified project. No part of the drawings, arrangements, or ideas therein shall be duplicated or used in whole or part for any other purpose whatsoever without the expressed written permission of ka inc. Materials 7017 Mineral Point Road - Proposed Development MADISON, WISCONSIN kainc.com UDC-7 August 5, 2009 ka#