VICTORIAN AND CLASSIC SHINGLES INSTALLATION DETAILS BERRIDGE MANUFACTURING COMPANY
|
|
- Claire Powers
- 5 years ago
- Views:
Transcription
1 VICTORIAN AND S INSTALLATION DETAILS MANUACTURING
2 INDEX INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INTRODUCTION TO TYPICAL DETAILS OVERVIEW VICTORIAN SHINGLE OVERVIEW VC-0 VCI-1 VCI-2 VCI-3 VC-2 VS-5 CS-5 EAVE DETAIL VC-10 RIDGE AND HIP DETAIL SHED ROO RIDGE CAP DETAIL RIDGE TERMINATION AT DORMER VALLEY GABLE DETAIL VC-20 VC-21 VC-22 VC-30 PARAPET DETAIL HEAD WALL DETAIL HEAD WALL DETAIL RAKE WALL DETAIL RAKE WALL DETAIL SLOPE TRANSITION DETAIL VC-40 VC-41 VC-42 VC-50 VC-51 VC-60 VALLEY DETAIL VC-70 PIPE PENTRATION 4" DIA. OR LESS ROO PENETRATION RECTANGULAR/SQUARE ROO PENETRATION SECTION DETAIL ROO PENETRATION SECTION DETAIL ROO PENETRATION SECTION DETAIL VC-80 VC-81 VC-82 VC-83 VC-84 MANUACTURING INDEX PAGE/ILE VC-0
3 A. B. C. VICTORIAN AND S: VICTORIAN AND S HAVE AN EXPOSURE O 9" X 12" MINIMUM SLOPE: THE VICTORIAN AND S ARE RECOMMENDED OR SLOPES O 3:12 OR GREATER. MATERIAL STORAGE: CAUTION MUST BE EXERCISED IN STORAGE O MATERIALS PRIOR TO INSTALLATION. KEEP ALL PREINISHED MATERIAL IN A DRY LOCATION WITH ADEQUATE VENTILATION AND OUT O DIRECT SUNLIGHT. EXPOSURE TO DIRECT SUNLIGHT AND/OR MOISTURE MAY CAUSE THE ACTORY APPLIED STRIPPABLE PLASTIC ILM TO ADHERE TO THE METAL PERMANENTLY AND DISCOLOR THE INISH. D. E.. G. H. STRIPPABLE ILM: THE STRIPPABLE PLASTIC ILM WHICH IS APPLIED OVER MOST PREINISHED PRODUCTS, PANELS, LASHINGS, COILS AND LAT SHEETS PROTECTS THE INISH DURING ABRICATION AND TRANSIT. THIS ILM MUST BE REMOVED PRIOR TO INSTALLATION. REQUIREMENTS: MANUACTURING RECOMMENDS THE USES O A MINIMUM O SOLID WOOD SHEATHING TO PROVIDE SUICIENT HOLDING POWER OR ASTENERS. CONTACT MANUACTURING'S ENGINEERING DEPARTMENT OR USE O ANY OTHER TYPE O. SHEATHING INSPECTION: 1. SHEATHING END JOINTS SHOULD BE STAGGERED. 2. ALL END JOINTS SHOULD MEET AT EITHER A JOIST OR RATER. 3. BLOCKING OR "H" CLIPS SHOULD BE USED ON PLYWOOD O JOINTS DO NOT REMAIN LAT UNDER THE WEIGHT O WORKMEN. 4. USE SHIMS TO KEEP ENTIRE SUBSTRATE EVEN. SUBSTRATE SHOULD BE LEVEL TO IN 20'-0". 5. ALL CUTS AT PENETRATIONS SHOULD BE TIGHT, WITHOUT GAPS. 6. USE WOOD RAMED CRICKETS AT LARGE PENETRATIONS. 7. MAKE SURE SUBSTRATE JOINTS ARE TIGHT AT ALL HIPS, VALLEYS AND RIDGES. ASCIA/RAKE INSPECTION: 1. STRIKE A LINE THE ULL LENGTH O THE ASCIA OR RAKE. I NOT STRAIGHT, CORRECT WITH SHIMS. 2. MAKE SURE ASCIA/RAKE IS LUSH WITH ROO SUBSTRATE SHEATHING. ELT UNDERLAYMENT: A SINGLE LAYER O NUMBER THIRTY ELT UNDERLAYMENT (OR EQUAL) MUST BE APPLIED OVER AS SHOWN IN THE MANUACTURING TYPICAL ELTING DETAILS. THE USE O ADDITIONAL LAYERS O NUMBER THIRTY ELT IS RECOMMENDED ON LOW-SLOPED ROOS, AT ALL VALLEY CONDITIONS, AT ROO PENETRATIONS, AND CERTAIN OTHER LASHING CONDITIONS AS DEPICTED IN THE VICTORIAN AND CLASSIC TYPICAL DETAILS. GRACE ICE AND WATER SHIELD MAYBE REQUIRED ON LOW SLOPED ROOS OR AT CERTAIN LASHING CONDITIONS. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE VCI-1
4 I. J. K. L. N. ELTING INSTALLATION: 1. DO NOT USE RED ROSIN PAPER UNDER METAL ROOING PANELS. 2. SWEEP ROO AREA CLEAN. 3. USE LAT HEAD GALVANIZED ROOING NAILS X 1- LONG WITH GALVANIZED ELT CAPS. 4. INSTALL VALLEY ELT IRST 5. INSTALL ELT PARALLEL TO EAVE (2 LAYERS REQUIRED AT EAVE), STARTING AT EAVE AND USING MINIMUM 6" LAPS. USE TWO LAYERS O ELT ON ENTIRE ROO DECK I SLOPE IS 3:12. 2 LAYERS REQUIRED AT EAVE REGARDLESS O SLOPE. 6. INSULATE BETWEEN WOOD BLOCKING AND METAL WITH ELT OR ICE AND WATER SHIELD. ELECTROLYSIS: AVOID ALLOWING LASHING AND PANELS TO COME INTO CONTACT WITH EITHER LEAD OR COPPER, AND PREVENT EXPOSURE TO WATER RUNDOWN ROM COPPER AND/OR LEAD. LASHING: I MANUACTURING IS TO SUPPLY LASHING, ALL LASHINGS WILL BE ABRICATED IN 10'-0" LENGTHS WITH SQUARE END CUTS ONLY. THE PURCHASER MUST PROVIDE ALL DIMENSIONS AND DEGREE O ANGLES. LASHING INSTALLATION: 1. REMOVE STRIPPABLE PLASTIC ILM ROM EACH SHINGLE PRIOR TO INSTALLATION. 2. START AT LOWER LET EAVE CORNER AND STAGGER AS SHOWN ON DETAIL VS-5 AND CS USE CHALK LINES TO KEEP SHINGLES STRAIGHT. 4. SHINGLES INTERLOCK AT SIDE LAP AND OVERLAP ROM COURSE TO COURSE. 5. WHEN SHINGLES REACH THE VALLEY OR HIP TRIM THE SHINGLES SO THAT THEY IT TIGHT INTO S. 6. TRIM SHINGLES AS NECESSARY AT THE RIDGE SO THAT THE BOTTOM EDGE O THE SHINGLE OLLOWS THE PATTERN O THE OTHER SHINGLES AND THE TOP O THE SHINGLE ITS TIGHT IN THE. ASTENERS: NAIL SHINGLES THROUGH LOCK SEAM WITH A MINIMUM O (2) 1- GALVANIZED ROOING NAILS. MAKE SURE ALL ASTENERS ARE DRIVEN STRAIGHT AND SET LAT. DO NOT OVERDRIVE ASTENERS, AS THIS WILL CAUSE BUCKLING O SHINGLES. O. SEALANT RECOMMENDATIONS: TREMCO INC. SPECTREM 1 OR EQUAL. DO NOT USE CLEAR CAULK **CONSULT MANUACTURING'S ENGINEERING DEPARTMENT REGARDING THE USE O ANY OTHER TYPE O ASTENER. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE VCI-2
5 MANUACTURING STRIVES TO PROVIDE ITS CUSTOMERS WITH THE HIGHEST QUALITY STRETCHER LEVELED STEEL AVAILABLE. THE LATEST TECHNOLOGY IS ALSO INCORPORATED IN 'S HIGH-PRECISION COIL HANDLING AND ROLL ORMING EQUIPMENT TO MINIMIZE THE STRESS ON METAL DURING PRODUCTION. URTHERMORE, UTILIZES HEAVIER 24 GAUGE METAL RATHER THAN 26 GAUGE STEEL OR LIGHT GAUGE ALUMINUM AS OERED BY MANY COMPETITORS. ALL THESE MEASURES HAVE BEEN TAKEN TO MINIMIZE THE AMOUNT O "OIL-CANNING" (WAVINESS) WHICH IS NATURALLY INHERENT IN LAT SHEET METAL MANY TIMES, HOWEVER, THE CAUSE O WAVINESS OR "OIL-CANNING" CAN BE TRACED TO UNEVEN SHEATHING, IMPROPER ELT INSTALLATION, IMPROPER HANDLING, OR OOT TRAIC ON THE PANELS. ALL ARCHITECTURAL PRODUCTS REQUIRE CARE IN HANDLING AND INSTALLATION TO AVOID DAMAGING OR DEORMING THE PANELS. THESE INSTALLATION INSTRUCTIONS AND THE OLLOWING TYPICAL DETAILS ARE INTENDED TO PROVIDE OUT CUSTOMERS WITH THE INORMATION REQUIRED OR AN AESTHETICALLY PLEASING AND UNCTIONAL INSTALLATION O THE VICTORIAN OR S. NOTE: ALL PRODUCTS, SPECIICATIONS, DETAILS, AND INSTRUCTIONS SUBJECT TO CHANGE WITHOUT NOTICE. OR SPECIIC PROJECT DETAILS, CONTACT MANUACTURING. MANUACTURING INSTALLATION INSTRUCTIONS PAGE/ILE BI-3
6 THE DETAILS CONTAINED IN THE OLLOWING PAGES ARE MERELY RECOMMENDATIONS AS TO HOW MANUACTURING MATERIALS SHOULD BE INSTALLED. THEY MAY REQUIRE ADAPTATIONS OR MODIICATIONS OR A SPECIIC PROJECT AS CONDITIONS VARY IN BOTH BUILDING DESIGN AND LOCAL WEATHER PECULIARITIES. MANUACTURING SHALL BE HELD HARMLESS ORM ANY AND ALL CLAIMS ARISING ROM LACK O WATERTIGHTNESS AS A RESULT O OLLOWING THESE RECOMMENDED DETAILS. ENSURING THE WATERTIGHTNESS ON ANY GIVEN PROJECT IS THE UNCTION O THE INSTALLER. THE ARCHITECT/GENERAL CONTRACTOR/INSTALLER MUST ACCEPT THE RESPONSIBILITY TO ADAPT THESE DETAILS TO MEET PARTICULAR BUILDING REQUIREMENTS AND TO ASSURE ADEQUATE WATERTIGHTNESS. THE INSTALLER CAN VIRTUALLY ASSURE WATERTIGHTNESS I THESE LASHING DETAILS HAVE BEEN PROPERLY ADAPTED, ADEQUATE LAPS HAVE BEEN PROVIDED, CORRECT TYPE O SEALANT USED, ALL JOINT ADEQUATELY CAULKED, AND PROESSIONAL WORKMANSHIP EMPLOYED. MANUACTURING INTRODUCTION TO TYPICAL DETAILS PAGE/ILE VC-2
7 MINIMUM 2 ASTENERS AT LOCK SEAM IELD CUT 1/2 SHINGLE TO CREATE STAGGERED PATTERN VICTORIAN SHINGLES VICTORIAN SHINGLE LOCK SEAM 12" EXPOSURE 9" EXPOSURE MANUACTURING OVERVIEW Victorian Victorian Classic Shingle Shingles PAGE/ILE VS-5
8 MINIMUM 2 ASTENERS AT LOCK SEAM IELD CUT 1/2 SHINGLE TO CREATE STAGGERED PATTERN S START AT EAVE, WORK ROM LET TO RIGHT 12" EXPOSURE LOCK SEAM 9" EXPOSURE MANUACTURING OVERVIEW Victorian Classic or Classic Shingle Shingles PAGE/ILE CS-5
9 VICTORIAN OR # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C. MAX. DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING AND ASTENERS ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING EAVE DETAIL PAGE/ILE VC-10
10 RIDGE/HIP CAP; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 20" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS, 20" O.C. MAX. # 30 ELT UNDERLAYMENT 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELTING UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE RIDGE/HIP CAP MANUACTURING RIDE AND HIP DETAIL PAGE/ILE VC-20
11 SHED RIDGE CAP; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS, POP RIVET TO AT 20" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR # 30 ELT UNDERLAYMENT LAP ELT OVER RIDGE ASTENERS; 40" O.C. MAX. CAULK ASTENER HEAD 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SHED RIDGE CAP MANUACTURING SHED ROO RIDGE CAP DETAIL PAGE/ILE VC-21
12 SECTION VIEW SECTION VIEW IELD ORM END O RIDGE LASHING AND EXTEND UNDER RIDGE LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ; DO NOT CAULK ON OR UNDER VICTORIAN OR VC-20 # 30 ELT UNDERLAYMENT VALLEY LASHING; 12" LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD PLAN VIEW MAIN ROO RIDGE LASHING CONTINUOUS VALLEY LASHING DORMER ROO MANUACTURING RIDGE TERMINATION AT DORMER VALLEY PAGE/ILE VC-22
13 VICTORIAN OR CONTINUOUS BEAD O CAULK TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS DRIP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE DRIP LASHING MANUACTURING GABLE DETAIL PAGE/ILE VC-30
14 CAP LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO COUNTER LASHING 40" O.C. MAX. CAULK ALL RIVET HEADS. ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK VICTORIAN OR 1 ON 12 ASTENERS AT LAPS AND STAGGERED; 20" O.C. AND CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT ASTENERS; 40" O.C. MAX. CAULK ASTENER HEADS ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. 1 ON 12 = INISH SIDE COUNTERLASHING SUB-LASHING CAP LASHING MANUACTURING PARAPET DETAIL PAGE/ILE VC-40
15 ASCIA PANEL COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTERLASHING SUB-LASHING MANUACTURING EAVE DETAIL PAGE/ILE VC-41
16 REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. COUNTERLASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT REGLET CONTINUOUS CAULK AT REGLET CONTINUOUS BEAD O CAULK CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTERLASHING SUB-LASHING REGLET LASHING MANUACTURING HEAD WALL DETAIL PAGE/ILE VC-42
17 # 30 ELT UNDERLAYMENT ASCIA PANEL ASTENERS; 20" O.C. MAX. LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS VICTORIAN OR # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENER; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE LASHING SUB-LASHING MANUACTURING RAKE WALL DETAIL PAGE/ILE VC-50
18 REGLET LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR REGLET CONTINUOUS CAULK AT REGLET CONTINUOUS BEAD O CAULK # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB-LASHING REGLET LASHING LASHING MANUACTURING RAKE WALL DETAIL PAGE/ILE VC-51
19 VICTORIAN OR TRANSITION LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEAD CONTINUOUS BEAD O CAULK VICTORIAN OR SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 40" O.C. # 30 ELT UNDERLAYMENT NOTE: PLACE A DAB O CAULK AT ASTENER LOCATION, DRIVE ASTENER THROUGH CAULK, AND CAULK ASTENER HEADS. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE 10" MIN. TRANSITION LASHING SUB-LASHING MANUACTURING SLOPE TRANSITION DETAIL PAGE/ILE VC-60
20 VICTORIAN OR IELD CUT AS REQUIRED TO VALLEY LINE BUTT ENDS OR WEEP DO NOT CAULK IN OR UNDER 9" MIN. CONTINUOUS BEAD O CAULK BETWEEN VALLEY LASHING AND ELT UNDERLAYMENT VALLEY LASHING 1" # 30 ELT UNDERLAYMENT ASTENERS, 24" O.C., PLACE A DAB O CAULK AT ASTENER LOCATIONS, DRIVE ASTENERS AND CAULK ASTENER HEADS 1. (BY OTHERS) TO BE A MINIMUM O PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE ASTEN THROUGH VALLEY UNDER LAP, NO ASTENERS TOP (OVERLAPPING) VALLEY 2 CONTINUOUS BEADS O CAULK AT LAPS ONLY AT TOP O LASHING ARE TO BE EXPOSED ON 12" LAPS 20" MIN. VALLEY LASHING 20" MIN. MANUACTURING VALLEY DETAIL PAGE/ILE VC-70
21 ROO PIPE PENETRATION O 4" IN DIA. OR LESS RUBBERIZED BOOT LASHING CONTINUOUS CAULK PIPE PENETRATION TO BE IN BODY O SHINGLE VICTORIAN OR SET RUBBERIZED BOOT INTO CONTINUOUS BEAD O CAULK. USE ASTENERS AS SPECIIED BY BOOT MANUACTURER CAULK ASTENER HEADS # 30 ELT UNDERLAYMENT CUT SHINGLE 1" SMALLER THAN PENETRATION, BACK CUT TABS, OLD TABS UP AROUND PENETRATION, AND CAULK. NOTE: I PIPE IS MADE O METAL, IT MUST BE PAINTED TO PREVENT RUST RUN-O ROM STAINING PANELS. NOTE: POSITION SQUARE BASED BOOTS IN A DIAMOND ORIENTATION WHERE POSSIBLE TO AID IN DIVERTING WATER. MANUACTURING PIPE PENETRATION 4" DIA. OR LESS PAGE/ILE VC-80
22 VICTORIAN OR VC-84 CARRY LASHING ROM VC-82 UNDER VC-84 ROM VC-84 TURN CORNER WITH VERTICAL LEG O LASHING ROM VC-84 VC-82 TURN CORNER WITH VERTICAL LEG O LASHING ROM VC-82 VC-83 CARRY LASHING ROM VC-83 UNDER VC-82 ROM VC-84 NOTE: SHINGLES ARE TO BE IELD CUT TO IT TIGHT AROUND PENETRATION MANUACTURING ROO PENETRATION RECTANGULAR/SQUARE PAGE/ILE VC-81
23 COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS CONTINUOUS BEAD O CAULK VICTORIAN OR CONTINUOUS BEAD O CAULK # 30 ELT UNDERLAYMENT TOP LAYER O ELT TO BE PARALLEL WITH ROO SLOPE ASTENERS; 20" O.C. MAX. PLACE A DAB O CAULK AT ASTENER LOCATION DRIVE ASTENER AND CAULK ASTENER HEAD CONTINUOUS BEAD O CAULK 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE SUB-LASHING MANUACTURING COUNTER LASHING LASHING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-82
24 COUNTER LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS ASTENERS; 20" O.C. MAX. LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. POP RIVET TO 40" O.C. MAX. CAULK RIVET HEADS SUB-LASHING; 4" END LAPS WITH CONTINUOUS CAULK AT LAPS. # 30 ELT UNDERLAYMENT CONTINUOUS BEAD O CAULK CONTINUOUS BEAD O CAULK VICTORIAN OR ASTENERS; 20" O.C. MAX. 1. (BY OTHERS) TO BE MINIMUM PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE LASHING SUB-LASHING COUNTER LASHING MANUACTURING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-83
25 VICTORIAN OR BUTT ENDS OR WEEP, DO NOT CAULK IN OR UNDER COUNTER LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS CONTINUOUS BEAD O CAULK BETWEEN LASHING AND ELT UNDERLAYMENT ASTENERS; 20" O.C. MAX. CONTINUOUS BEAD O CAULK LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS 9" MIN. SUB LASHING; 4" END LAPS WITH COTINUOUS CAULK AT LAPS # 30 ELT UNDERLAYMENT ASTENERS, 20" O.C., PLACE A DAB O CAULK AT ASTENER LOCATIONS, DRIVE ASTENERS AND CAULK ASTENER HEADS 1. (BY OTHERS) TO BE A MINIMUM O PLYWOOD OR EQUIVALENT IN STRENGTH OR HOLDING POWER O ASTENERS. 2. ALL ELT UNDERLAYMENT, CAULKING, AND ASTENERS, ARE ITEMS TO BE URNISHED AND INSTALLED BY THE ROOING INSTALLER AT THE DISCRETION O THE ARCHITECT. = INISH SIDE COUNTER LASHING LASHING SUB LASHING MANUACTURING ROO PENETRATION SECTION DETAIL PAGE/ILE VC-84
CLEANROOM GEL GRID CEILING SYSTEM PRODUCT DATA Division
5023 HAZEL JONES ROAD, BOSSIER CITY, LA 71111 888.315.1561 800.877.8746 FAX SALES@GORDONCLEANROOM.COM GORDONCLEANROOM.COM AN EMPLOYEE OWNED COMPANY CLEANROOM GEL GRID CEILING SYSTEM PRODUCT DATA Division
More informationProduct Guide. Latitude Series High-Performance Exterior Metal Wall Panels for Horizontal and Vertical Concealed Clip Application
Product Guide Latitude Series High-Performance Exterior Metal Wall Panels for Horizontal and Vertical Concealed Clip Application Blank Text www.imetco.com (800) 646-3826 Page 2 Contents Standard Profile...
More informationLPCorp.com
T R E A T E D E N G I N E E R E D W O O D C L A D D I N G E N G I N E E R E D F O R C O M M E R C I A L A P P L I C A T I O N S LPCorp.com 888.820.0325 1 LAP & SIDING CEDAR TEXTURE LAP The bold look of
More informationTESTING APPLICATION STANDARD (TAS)
TESTING APPLICATION STANDARD (TAS) No. 00(A)-9 TEST PROCEDURE FOR WIND AND WIND DRIVEN RAIN RESISTANCE AND/OR INCREASED WINDSPEED RESISTANCE OF SOFFIT VENTILATION STRIP AND CONTINUOUS OR INTERMITTENT VENTILATION
More informationSECTION SHOWER AND BATH ENCLOSURES. Display hidden notes to specifier by using Tools / Options / View / Hidden Text.
SECTION 10185 SHOWER AND BATH ENCLOSURES Display hidden notes to specifier by using Tools / Options / View / Hidden Text. PART 1 GENERAL 1.1 SECTION INCLUDES A. Bathtub wall enclosures. B. Shower wall
More informationPrecision Duct Systems 4570 Commerce Cir SW Atlanta, GA Phone (404)
Project Name: Engineer: Contractor: Section Number: Date Submitted: Date Approved: Pressure Class: Material Type: Connections: 2005 Up to 10 wg 1995 2 wg pos 1995 4 wg pos 1995 10 wg 2005 neg WG: 1995
More informationBody - May vary in shape, body beads may be present, and is constructed of electrolytic tinplate (ETP).
2 1 2. CAN TERMINOLOGY Any discussion or description of can defects requires standard terminology relating to the can components (end, body, double seam). The terminology required to describe these components
More informationHIPPLOCK. User s Safety Manual
HIPPLOCK User s Safety Manual This temporary roof anchor device is intended to be used in compliance with OSHA s subpart M (1926.500) as part of a personal fall protection system under the oversight of
More informationBERRIDGE ZEE-LOCK DOUBLE-LOCK SEAMER
OPERATIONS MANUAL BERRIDGE ZEE-LOCK DOUBLE-LOCK SEAMER Berridge Manufacturing Company OWNER: DATE: SER. NO.: CONTENTS I. GENERAL DESCRIPTION... 2 II. EQUIPMENT NOMENCLATURE, FEATURES & SPECIFICATIONS...
More informationPermanent Roof Anchors
User Instruction Manual Permanent Roof Anchors Part Number: RL-02(A) ISO 9001: 2008 Registered Manual 103-0062 General Safety Information Under Penalty of Law This User Instruction Manual is not to be
More informationNUWALL METAL WALL PANEL METL-SPAN CONCEALED FASTENER SINGLE-SKIN PANELS
NUWALL METAL WALL PANEL NuWall combines the ease of installation in both new and retrofit applications with the pleasing aesthetic appeal of a clean, uninterrupted wall. For retrofit construction, all
More informationS110 Steel Level Panel Installation Instructions
S110 Steel Level Panel Installation Instructions NOTE: Fairway Architectural Railing Solutions will not be held liable for incorrect or unsafe installations by installer. It is the installer s resposibility
More informationrondo aluminium components
rondo aluminium components The Rondo Aluminium Ceiling System is an alternative to the Rondo DUO Exposed Grid Ceiling System. Unlike the DUO system, the Aluminium Main Tee to Cross Tee intersection is
More informationWAVE CYBER HANDLING &
WAVE CYBER PRESSURE VESSEL LIFTING, HANDLING & INSTALLATION INSTRUCTIONS 1 Contents Page Rating, Receiving... 3 Basic Handling Rules... 4 UV Protection... 8 Vacuum Protection Flex Connectors... 9 Flexibility
More informationBike-Shell Model 301P
Bike-Shell Model 301P NEW design, one piece FRP Composite bike locker NO ASSEMBLY required Specify the 300 Series lockers for the highest customer satisfaction from the no-assembly ready-touse delivery
More informationWater Management Residential Podium Construction BSC Experts Session Overview. Overview
Building Science Experts' Seminar Water Management Residential Podium December 11-12, 2013 Peter Baker, P.Eng. Water Management Residential Podium BSC Experts Session 2013 Overview Building Enclosure Commissioning
More informationS Surge Arresters
Surge Arresters UltraSIL Polymer-Housed VariSTAR Type US, UH, and UX Station-Class Surge Arresters Installation and Maintenance Instructions Service Information S235-88-1 Contents Product Information...........................1
More informationBARRIER OFFSET 0" A 6" 6" A 12" 12" A 26" A 26" 3A OR 4A L OR S * ** L OR S L OR S
ACCEPTABLE (TCB) TYPES AND ANCHORING DETAILS BASED ON UNDERLYING SURFACE TYPE AND BARRIER OFFSET FROM DROP-OFF BARRIER OFFSET UNDERLYING SURFACE 0" A 6" 6" A 12" 12" A 26" A 26" TCB TYPE DETAIL TCB TYPE
More informationSorcerer and Warlock
Sorcerer and Warlock Advanced Software for Roof and Wall Design and Estimating Tutorial - Crickets Revision: 1.1 12 August 2009 English Units / Feet-Inches AppliCad Tutorial Big Crickets Page 2 Tutorial
More informationINSTALLATION & OPERATION MANUAL AORCS ATLAS OPERATING ROOM CEILING SYSTEM. Redefine your comfort zone.
INSTALLATION & OPERATION MANUAL AORCS ATLAS OPERATING ROOM CEILING SYSTEM IOM AORCS ATLAS OPERATING ROOM CEILING SYSTEM Table of Contents Inspection...3 Examination...3 Preparation...3 Installation...4
More informationDomed Ceilings and Barrel Vaults
Page 1 of 12 Domed Ceilings and Barrel Vaults USG Drywall Suspension System These installation instructions are divided into two parts: Part 1 applies to domed ceilings, and Part 2 applies to vaulted ceilings.
More informationUSG Ceiling Solutions. LOGIX Integrated Ceiling Systems INSTALLATION GUIDE
USG Ceiling Solutions LOGIX Integrated Ceiling Systems INSTALLATION GUIDE LOGIX Integrated Ceiling Systems INSTALLATION GUIDE Logix Brand Integrated Ceiling Systems integrated ceiling systems from USG
More informationUtility Anchor System
Utility Anchor System The Dayton Superior Utility Anchor System is designed to economically simplify the lifting and handling of precast concrete elements. Its economics, ease of use and versatility will
More informationThis machine is setup to seam 1.5 panel - 180⁰ seam
This machine is setup to seam 1.5 panel - 180⁰ seam Instructions to change this setup are included in this Guide. (You may discard this page.) CONTRACTOR SERIES ROOF SEAMER UNIVERSAL CONVERSION KIT PLEASE
More informationTECHNICAL BULLETIN USE OF SNOW GUARDS
Page 1 of 10 USE OF SNOW GUARDS Snow guards are used to hold snow and ice on the roof until they can melt and run off as water. Their use should be restricted to areas where snow and ice falling off the
More informationTABLE OF CONTENTS International Racquetball Federation officially approved specifications. Copyright 01/13/1983; rev.
Racquetball Court Specifications TABLE OF CONTENTS International Racquetball Federation officially approved specifications. Copyright 01/13/1983; rev. 1988; 1997, 2013 SECTION ONE: Performance and Specifications
More informationNICROS-GRANITPANELS INSTALLATION MANUAL
NICROS-GRANITPANELS INSTALLATION MANUAL NICROS, INC. 845 PHALEN BLVD. ST. PAUL, MN 55106 PHONE: 651.778.1975 FAX: 651.778.8080 THANK YOU FOR YOUR PURCHASE OF THIS NICROS PRODUCT Nicros-GranitPanels are
More informationInflatable Stand Up Paddle Board Manual
Inflatable Stand Up Paddle Board Manual V-Max AIR 12 6 Voyager AIR 11 6 Koa AIR 10 2 and 10 8 Heavy duty built in carrying handles Steel D Ring Built in Cargo Straps EVA Deck Pad High Pressure Air Valve
More informationPro-Form Direct Vent System
The Pro-Form direct vent system has best in industry features that provide ease of installation, extreme durability and superior performance. The Pro-Form direct vent system is fully tested and listed
More informationLED 14W POLO BULKHEAD WITH MICROWAVE SENSOR
INTRODUCTION The LED 14W POLO Bulkhead is a modern lowcost and energy efficient fitting ideal for domestic and utility applications. SPECIFICATION LED 1150lm IP54 220-240V IK09 4000K 50/ 60Hz >82 Ra 14W
More informationTECHNICAL DATA. TRIMPAC Model B-5 & B-5B
September 16, 2013 Trimpac 250a 1. DESCRIPTION DEsCRIPTIoN is a factory assembled trim package for a ed an electric/pneumatic release module in a metal enclosure. The standard trim normally required on
More information8. Fall Protection Procedures WAC
1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall
More informationTECHNICAL DATA. Trimpac 251a. Spetember 16, 2013
Spetember 16, 2013 Trimpac 251a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-6 and B-6B is a factory assembled trim package for a double interlocked preaction system with an electric/pneu-lectric release
More informationHandle the film very carefully. As with aluminum foil, once creased, the film will remain creased.
RECOMMENDED TOOLS: Bottled water (not tap water) Spray bottle Squeegee or squeegee card Break-away utility knife (for cutting film) Single-edged razor blade (for cleaning glass) Ruler or tape measure Soft,
More informationA N C H O R T A B S N O R T H W E S T ANCHOR TAB VF. Patented. User Instructions
A N C H O R T A B S N O R T H W E S T www.anchortabs.com ANCHOR TAB VF Patented User Instructions National standards, and state, provincial, and federal laws, require installer/user of this product to
More informationFOLD AND ROLL PLAYBACK TABLE TENNIS TABLE
OWNER'S MANUAL FOLD AND ROLL PLAYBACK TABLE TENNIS TABLE MODEL NOs. T8269 T8169 Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such
More informationFOLD AND ROLL PLAYBACK TABLE TENNIS TABLE
OWNER'S MANUAL FOLD AND ROLL PLAYBACK TABLE TENNIS TABLE MODEL NOs. T8268 T8168 Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such
More informationSection 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices. Unit Objectives. Pressure Vessels and Piping (1 of 2)
Section 2 Safety, Tools and Equipment, Shop Practices Unit 4 General Safety Practices Unit Objectives After studying this chapter, you should be able to: Describe proper procedures for working with pressurized
More informationInstructions for the following series products:
Instructions for the following series products: U-Bolt Roof Anchors (See back page for specific model numbers.) User Instruction Manual U-bolt Roof Anchor This manual is intended to be used as part of
More informationMSC Guidelines for Independent Fuel Tanks
References: Contact Information a. 46 CFR 58.50 (Independent Fuel Tanks) b. 46 CFR 119.440 (Independent Fuel Tanks) c. 46 CFR 182.440 (Independent Fuel Tanks) C. J. Robuck, LCDR, Chief, Engineering Division
More informationPOP UP ANCHOR. Part Number Spectrum Lane ~ Missoula MT ~
POP UP ANCHOR Part Number 153169 7100 Spectrum Lane ~ Missoula MT 59808 800.791.8056 ~ www.spectrumproducts.com You have purchased a Spectrum Products Pop Up Lane Rope Anchor. Providing the unit is installed
More informationInstallation and Maintenance Manual. Compact Medical Gas Outlets
Installation and Maintenance Manual Compact Medical Gas Outlets Contents Product Description 3 Cleaning and Lubricating 4 Inspection and Testing 4 Installation and Dimensions 5-6 Compact Outlet Indexing
More information3M DICHROIC Glass Finishes
3M DICHROIC Glass Finishes DF-PA DF-PA Chill Chill & & DF-PA DF-PA Blaze Blaze Doc TypeInstallation Product #Guide (opt.) Revision D, April 2018 Product Description 3M DICHROIC Glass Finish DF-PA (the
More informationRight-Angle Tube Roller Model
SPECIFICATIONS Model no. Free Speed (RPM) Throttle Rotation Max. Torque Ft-Lb Air Pressure psi Air Inlet Hose Air Flow @Free Speed Spindle Weight 909-1700 95 Lever type Reversible 240 90 1/2 NPT 1/2 I.D.
More informationTECHNICAL DATA SINGLE INTERLOCKED PREACTION SYSTEM WITH PNEUMATIC RELEASE
1 of 10 1. DESCRIPTION (Refer to Figures 1-3.) Viking supervised Single Interlocked Preaction Systems utilize a Viking Deluge Valve and a pneumatically pressurized automatic sprinkler system. The system
More informationModular skylight warranty
Modular skylight warranty Specific limited product warranty 10 year limited warranty (a) (b) (c) VELUX insulating glass For a period of (10) ten years from the date of purchase, VELUX warrants to the end-user
More informationCARBOLINE NORGE AS QMS INCORPORATED DOCUMENT
Carboline Norge AS CARBOLINE NORGE AS QMS INCORPORATED DOCUMENT Page 1 of 5 1 PURPOSE This procedure has been made to assure that the material is correctly used, and that the work is properly done, on
More informationREFLECTIT. Reflectit Spray Application Instructions DS % Acrylic Coating Providing a Pearlescent Appearance
REFLECTIT 100% Acrylic Coating Providing a Pearlescent Appearance Reflectit Spray Application Instructions I. General Instructions The following instructions apply to using Binks 2001 pressure pot spray
More informationKTM OM-2 SPLIT BODY FLOATING BALL VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood SECTION 1 - STORAGE 1.1 Preparation and preservation for storage All valves should be properly packed in order to protect the parts
More informationExterior Trim. Product Specification Guide
Exterior Trim 2018 Product Specification Guide Trimboards Smooth/Smooth, Natural White CERTAPAK FULL UNIT HALF UNIT 5/8 in. 5/8 in. x 6 in. x 18 ft. 5/8 in. x 5-1/2 in. x 18 ft. 11040618005 4 160 2880
More informationORNAMENTAL ALUMINUM FENCING
ORNAMENTAL ALUMINUM FENCING Clearfi eld Fencing Direct offers fencing to meet your every need. With a variety of fence styles, colors and accessories - virtually endless design possibilities can be created
More informationSIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
More informationSummit Anchor Company, Inc.
Summit Anchor Company, Inc. Safety From The Top Down Roof and Wall Safety/Tie-Back Anchors Suspended Access Systems and Fall Protection Overview United States and Canadian national safety standards require
More informationREFER TO AQUATHERM TECHNICAL BULLETIN A-AQTTB FOR ADDITIONAL INFORMATION AND SAFETY PRECAUTIONS
Aquatherm Standard Pressure Testing Procedure Aquatherm offers an extensive warranty to protect against damages caused by failure from manufacturer s defect. Aquatherm requires that all installations be
More informationTHE PROCESS OF JOINT INTEGRITY
BOLTED JOINTS A.333 THE PROCESS OF JOINT INTEGRITY To assist in managing a process, ask yourself the following questions: why, what, who, and how? Why do we need a Flange Joint Integrity program? This
More information602 STRINGING MACHINE OWNER'S MANUAL
PROGRESSION 602 STRINGING MACHINE OWNER'S MANUAL AL Issue 1- April 2000 Copyright 2000 GAMMA Sports - All Rights Reserved PROGRESSION 602 STRINGING MACHINE TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 331a 1. Description Viking supervised Double-Interlocked Electric/Pneumatic Release Preaction Systems utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated
More informationMetal Roofing
Metal Roofing Does your roof need snow guards? Alpine SnowGuards snow retention systems are important for any lowfriction, sloped roof. Snow and ice can avalanche off a low-friction, sloped roof and pose
More informationtubepress press procedure
tubepress press procedure tubepress 15mm up to 35mm tubepress 15 mm up to 35 mm 1. The tube ends must be clean with no scratches or grooves. Remove end caps. Cut tube to length. 2. Deburr tube inside and
More informationHot Tub Pre-Delivery Guide
Hot Tub Pre-Delivery Guide To prepare for the delivery of your hot tub, make sure the delivery path is clear and no obstructions are present. Obstacles such as overhanging tree limbs, awnings, protruding
More informationgalvanized bins galvanized bins
galvanized bins galvanized bins Since launching our product line over 65 years ago, Meridian has set the standard in excellence for the storage and handling industry. Meridian has continuously incorporated
More informationA A A T E C H N O L O G Y
A A A T E C H N O L O G Y & SPECIALTIES CO., INC. C O N S T A N T E F F O R T S U P P O R T S TOTAL SOLUTION SERVICE For the Industrial Piping Marketplace 2012 www.aaatech.com 4 1 Y E A R S S E R V I N
More informationInstallation Instructions
Round Type B Gas Vent Model E - Sizes 3" through 6" Model R - Sizes 7" through 30" HART & COOLEY GAS VENT AND ACCESSORIES ARE FOR USE ONLY WITH LISTED GAS-FIRED APPLIANCES EQUIPPED WITH A DRAFT HOOD OR
More informationInstruction Manual. PE-25/32/37 Tapping Machines. POLYTAPP Valves
Instruction Manual PE-25/32/37 Tapping Machines & POLYTAPP Valves Nov 2016, Revision 2 Document Number 3000111 2 M.T. Deason Company, Inc. PO Box 101807 Birmingham, AL 35210 Phone: 205 956 2266 Fax: 205
More informationPart #: 15158; 15159; 15188; 61027; 61029; 61140; 61141
Product Name: Guardrail Receivers Part #: 15158; 15159; 15188; 61027; 61029; 61140; 61141 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationInstallation Instructions Topo Ceiling System
Topo Ceiling Page 1 of 12 Before beginning installation of the TOPO Ceiling, check the enclosed bill of materials to ensure that all parts are present and undamaged. Read all installation instructions
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 10801 - TOILET AND BATH ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions apply to this Section.
More informationThe Outer Seal is highly abrasion resistant and provides mechanical stiffness to the splice in order to better match the cable stiffness.
The Sealing Compound encapsulates the electrical splices, provides a strain relief for the conductors, acts as a water block, eliminates air voids which tend to act as pumps to draw in water during pressure
More informationOperating Instructions in compliance with Pressure Equipment Directive 2014/68/EU. FAS Brass Check Valve RDL
Operating Instructions in compliance with Pressure Equipment Directive 2014/68/EU FAS Brass Check Valve RDL Please read these operating instructions carefully to ensure a safe operation and keep the same
More informationCoiling Tube with Twist-Proof Fitting
http://www.pisco.co.jp FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Anti-Twisting Coiling Tube for Air Tool Coiling Tube with Twist-Proof Fitting 306 Avoid Twisted Tube Problem
More informationGeneral Information Gravity roller conveyors are available in many sizes and configurations as shown on the following pages. There are many factors to consider when selecting a gravity conveyor. The following
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION 6" X 8" (NOMINAL POST) 3-1/2" DIA. 2 HOLES TAPERED HARD WOOD WEDGES (HARDWOOD WEDGE
X (NOMINAL POST) 1-1/ DIA. 2 HOLES X 8" (NOMINAL POST) 3-1/ DIA. 2 HOLES TAPERED HARD WOOD WEDGES (HARDWOOD WEDGE TO BE OAK, MAPLE OR OTHER APPROVED DENSE HARDWOODS) TO HOLD POST IN A STABLE POSITION AFTER
More informationL.Ph. Bolander & Sons 1355 Evans Ave. 800/
L.Ph. Bolander & Sons 1355 Evans Ave. 800/434-5611 San Francisco, Ca. 94124 Fax 415/648-0402 GOUNDSET ALUMINUM FLAGPOLE INSTALLATION INSTRUCTIONS STEP 1: DIG THE HOLE TO THE DIMENSIONS LISTED BELOW STEP
More informationPORTABLE LIGHTNING MAST PROTECTION PLP SERIES INSTRUCTION MANUAL
PORTABLE LIGHTNING MAST PROTECTION PLP SERIES INSTRUCTION MANUAL LBA Technology, Inc. Greenville, NC May 20, 2014 Rev 061515 NOTICE This Instruction Manual is prepared by LBA Technology, Inc. specifically
More informationCOOPER POWER SERIES. 50 A 2:1 series multiple (dual voltage) switch cap/wrench, lever or hotstick operable handles installation instructions
Voltage Regulators MN800013EN Effective February 2016 Supersedes S800-70-1 August 2012 COOPER POWER SERIES 50 A 2:1 series multiple (dual voltage) switch cap/wrench, lever or hotstick operable handles
More informationSTATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING
9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS
More informationXSPLATFORMS ROOFTOP SYSTEMS -
XSPLATFORMS Since 1995, XSPlatforms has built a compelling track record designing, manufacturing, assembling, inspecting, and managing rooftop fall protection systems worldwide. XSPlatforms systems are
More informationFLEXIBLE SHAFTING (Wet & Dry)
TM-5 April 5, 2004 Elliott offers a complete line of precision tube tools, including: tube expanders Boiler Expanders Heat Exchanger Expanders Condenser Expanders Refinery Expanders tube rolling motors
More informationExterior Trim. Product Specification Guide
Exterior Trim 2019 Product Specification Guide Trimboards Smooth/Smooth, Natural White CERTAPAK FULL UNIT HALF UNIT Nominal Actual Order Number* PCS/UNIT PCS/UNIT LF/UNIT Weight** PCS/UNIT LF/UNIT Weight**
More informationSCOUT DECK ANCHOR 3 1/4" BONDING SCREW
SCOUT DECK ANCHOR 16" 16" 1" X 4" ANCHOR BOLT (4) 10" 3 1/8" 5" 6" MIN COPPER WIRE TO ATTACH TO BONDING GRID 3 1/4" BONDING SCREW CONCRETE DECK SPECIFICATIONS: THE AQUA CREEK PRODUCTS' SCOUT DECK ANCHOR
More informationPole & Tree Climbers. Pole & Tree Climbers. 1972AR Series. Pole Climbers with 1-1/2" Gaffs Complete Set
MADE IN USA 8" x 8" (203 x 203 mm) cushioned, high-grade leather climber pads for maximum comfort. Adjustable climber length. Steel sleeve moves in 1/4" (6 mm) increments for the most comfortable fit.
More informationYoke Block Instruction Manual
Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These
More information1. BLADE STAND-OUT 3m (10ft): 1,4m (4-2/3ft) / 5m (16ft): 1,8m (6ft) / 8m (26ft): 2,0m (6-1/2ft)
86 LAYOUT TOOLS IRWIN TAPE MEASURES IRWIN Tools offers a new full range of measuring tapes designed for tradesmen looking for accuracy, comfort and durability. The range features a brand new ergonomically
More informationTECHNICAL DATA. Q = C v P S
January 6, 2012 Preaction 333a 1. Description Viking supervised Surefire Preaction Systems Utilize the Viking G-3000P Valve. The small profile, lightweight, pilot-operated Viking G-3000P Valve comes complete
More informationTECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS
TECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS CONTENTS: 1.0 General Information 2.0 Preparation and Splicing of PinPoint Wire 3.0 PinPoint Direct Bury Splice Kit Specifications
More informationSPIRAL PIPE - OVAL SINGLE WALL
SPIRAL PIPE - OVAL SINGLE WALL Duct Direct Pipe and Fittings are manufactured in accordance with 2005 SMACNA Duct Construction Standards (1995 SMACNA Standards on request) OVAL SUBMITTAL Oval Single Wall
More informationProduct Name: Alligator Guardrail System
Product Name: Alligator Guardrail System Part #s: 15167; 61074; 61075; 15161; 15162; 15168; 15165; 15166; 61027 Instruction Manual Do not throw away these instructions! Read and understand these instructions
More informationBALL STOP INSTALLTION GUIDE
BALL STOP INSTALLTION GUIDE GROUND SLEEVE INSTALLATION: 1. Locate the exact location of the ground sleeve. NOTE: Maximum recommended pole spacing is 20 feet on center. 2. Excavate the pole footing; refer
More informationUser Instruction Manual For Davit Rescue System
Instructions for the following series products: Rescue Davit System Model numbers 8004000 and 8302500 User Instruction Manual For Davit Rescue System This manual should be used as part of an employee training
More informationFall Protection Refresher Orientation. Fall Protection Refresher Orientation 1
Fall Protection Refresher Orientation Fall Protection Refresher Orientation 1 Course Objectives! Understand the definitions of fall prevention, fall restraint, and fall arrest.! Understand the requirements
More informationNEXT GENERATION FLEX FENCE
NEXT GENERATION FLEX FENCE Area To Be Fenced.. With Next Generation Flex Fence any post that is not in a straight line with another post must be braced. Layout your fence installation. Determine all end
More informationSPOOLER INSTRUCTIONS. STEP 12 If you are going to paint your posts, that should be done at this time.
STEP 4 Starting where you marked the end post location, move down your fence line 6 feet and make another mark. This mark is where your second upright post will be installed. Continuing down the fence
More informationTechnical Service Bulletin June 2015 TSB122.06
Technical Service Bulletin June 2015 TSB122.06 Element Loading Guidelines This bulletin provides general information and guidelines for installing Hydranautics elements in order to provide optimally reliable
More informationWarranty. The VELUX promise. Specific limited product warranty 10-year No Leak installation warranty Warranty claim procedure
Warranty The VELUX promise Specific limited product warranty 10-year No Leak installation warranty Warranty claim procedure 20 year limited warranty VELUX insulating glass (b)(c) For a period of (20) twenty
More informationAluminium. Overview. Door stops. Pull handles. Cabinet knobs. Card frames. Cable box. Numerals. Indicators. Budget lock roses.
Accessories Overview Door stops Pull handles Cabinet knobs Card rames Cable box Numerals Indicators Budget lock roses Window locks Door viewer Key tag Flush pulls Flush ring handles Engraving 78 79 88
More informationITEM 400 STRUCTURAL EXCAVATION AND BACKFILL
AFTER MARCH 1, 2012 ITEM 400 STRUCTURAL EXCAVATION AND BACKFILL 400.1 Description. This item shall govern for all excavation required for the construction of all structures, except pipe or box sewers for
More informationFirestop Products and Systems Estimating Guide
F i rr eessttooppppi ni ng g http://flamesafe.rectorseal.com PRODUCT DATA UPDATES TECH LETTERS DETAILS MSDS CONTACTS FAQS Firestop Products and Systems Estimating Guide Through-penetrations Estimating
More informationTECHNICAL DATA. Trimpac 244a. September 16, 2013
September 16, 2013 Trimpac 244a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-1 and B-1B is a factory-assembled trim package with an electric release module in a metal enclosure. The standard trim normally
More information