Watts Modernization Package HS-200 PT Reverse Osmosis Processor Getinge Part #

Transcription

1 Equipment modernization package Watts Modernization Package HS-200 PT Reverse Osmosis Processor Getinge Part # PPLITION The HS-200 PT RO Processor is specifically designed to supply treated water for point-of-use electric steam generators to significantly reduce or eliminate boiler scaling and to extend peak equipment performance. This unit is intended for use with a single sterilizer/electric boiler combination with boilers in the range of 12 to 30 KW. FETURES Universal mounting system for quick, easy installation. ttractive Stainless Steel abinet. Small size (24 x16 x20 ) permits installation virtually anywhere. ENEFITS Requires service connection to cold / hot water supply and drain. No electrical requirement. Extended life from boiler heating element. Increased reliability fewer equipment breakdowns due to boiler scaling. onvenient quarterly maintenance intervals with economical PM packages available. SPEIFITIONS Provides 5-50 TS output water from potable water sources up to 2000 TS, 250 ppm or 14 grains hardness. MTERILS N SERVIES SUPPLIE Self contained RO Processor including filters, housings, pressure tank, bypass valve and permeate pumps in a stainless steel cabinet. Includes connection to equipment. WRRNTY Watts HS-200 PT systems are warranted for one year. Labor for repairs is provided for 90 days following installation and start-up. Warranty repairs will be performed Monday through Friday, 8am to 5pm, excluding weekends and Holidays. PM package (available separately) Includes a year s supply of consumable components.

2 HS-200 PT Installation Instructions Refer to drawing 2 in this brochure for mounting instructions, minimum service clearances and service connections. Utility Requirements: Note: floor drain within 10 feet of the oiler Mate is required. ½ potable cold water supply 2gpm, degrees F, psig TS, 250ppm or 14 grains hardness Operation Once all service and output connections are made, simply turn on cold water supply to the unit. Maintenance Quarterly - Replace pre-filters items # 1, 2, 3, & 8. nnually - Replace membrane cartridges item# 4. Replacement Parts PM Package Part# PM package includes a 1 year supply of Items #1, 2, 3, 4 & 8 Individual part numbers for component parts refer to drawing 1 in this brochure. (Front view with access panel removed)

3 LEFT SIE FRONT (ESS PNEL SIE) MNUL YPSS VLVE FOR RPI STRTUP / OILER FILL M-200 PROESSOR SPEIFITIONS 1) INLET WTER: MUST E POTLEWTER THT IS MIROIOLOGILLY SFE. 2) ONNETIONS: 1,2 & 3 RE 1/2" NPT; L GRE OPPER WITH FLIRE FITTINGS REQUIRE. 3) PRESSURE: MIN. 40 PSI, MX 90 PSI (OPTIMUM 65 PSI) PRESSURE REGULTOR P/N REQUIRE IF OVER 90 PSI. 4) PH RNGE: 4-7 PPM. 5) HRNESS: MXIMUM 10 GRINS OR 171 PPM. 6) TEMPRTURE: MIN 40 EG. F MX 100 EG. F (OPTIMUM 77 EG. F). 7) TS: MXIMUM 1200 PPM OR 500mg/L Nal 8) First year preventitive maintenance kit included. (P/N ) 9) LERNE: MINIMUM 18" SERVIE LERNE ON SIES &, MINIMUM 35" ON SIE. 10) FLOOR RIN REQUIREMENTS: MIN. 1/2" I. WITHIN 10' OF PROESSING UNIT (3) FEE WTER ONNETION (1/2" NPT) (2) ONENTRTE WTER ONNETION (1/2" NPT) (1) PERMETE WTER ONNETION (1/2" NPT) OLT HOLES FOR EILING MOUNT (4 PLES) 3/8" THRE STOK WITH WSHERS N LOK NUTS REQUIRE RIGHT SIE IR VLVE ESS PNEL TNK NEES TO E EMPTY WHEN HRGING TO THE REQUIRE 15 P.S.I SOURE OF SUPPLY: PROESSOR P/N MFG: Watts Pure Water Phoenix, Z US RWN raig Schmitt 7/8/2003 HEKE Watts Premier Q TITLE 4 TOP VIEW (ESS PNEL) 3 MFG PPROVE 2 M200 Installation Specifications SIZE WG NO REV SLE M-200 SHEET 1 1 OF 1 07/07/03

4 Equipment Outlet (Product Water) rain Outlet Tapwater Inlet Threaded Rod Threaded rods attached to ceiling Panel over 20-1/4 18 ir Tank ccess 12 Rods run through all four corners. 24 ESS RE ESS RE Flat Washer Nylon Lock Nut Nylon lock nuts & flat washers lock rods at top & bottom Four djustable Leveler Feet of M-200 enclosure NOTE: Need access to front panel and right side ir Tank ccess ap. Recommended: Front Panel ccess - 18 clearance Side Panel ccess - 12 clearnace ottom panel Rear panel alifornia ode requires four sizemic mounting holes for floor attachment Mounting holes for stud attachment on 18 or 16 centers Metal or wood stud %%c.50 E1 G 1 E Top View %%c.50 E 1 E 2 E G 2 G 3 3 E4 G 4 E %%c.375 %%c 2.50 ottom View E E E 4 E 5 E Rear View 1.95 Side View F RWN NME NELSON. TE WEIGHT: O NOT SLE RWING 77 LS TITLE: M-200 oilermate ENG. PRO. SHMITT. HENSS M. WG NO. MTERIL: M Stainless Steel 2 SLES HNFOR J. REVISION 7/15/02 Q. MNGIN P.

5 TPWTER INLET GREEN TUING EQUIPMENT OUTLET 10 X 9 LK TUING RIN OUTLET LK TUING 1 LK TUING 2 3 LUE LUE LUE LK > LK > LK TUING 7 8 PERM IN LUE PERM OUT RINE IN RINE OUT PERM IN PERM OUT RINE IN RINE OUT PERM IN PERM OUT RINE IN LK LUE LK LUE LK RINE OUT LK TUING ITEM PRT NUMER ESRIPTION MIRON SEIMENT FILTER G/KF MIRON RON LOK MEMRNE TFM 100 GP ML FLOW RESTRITOR PERMETE PUMP WITH LIP PRESSURE TNK LL LITE /2 RSS HEK VLVE /2 Y PSS VLVE ON UNIT ONNETION SIZE PPROVE MTERIL PERMETE WTER TO OILER 1/2 FPT 1/2 L OPPER ( SWET OR FLIR ) RIN WTER ONNETION 1/2 FPT 1/2 L OPPER/PV/POLY PROPYLENE INLET OL WTER ONNETION 1/2 FPT 1/2 L OPPER/PV/POLY PROPYLENE E IR TNK ESS MOUNTING LOTION 2 1/2 OPENING SIZE TIRE PRESSURE GUGE 0-50 PSI RNGE PPROVE MTERIL E 1-4 EILING MOUNT ( TOP PNEL ) 3/8 THREE STOK E1-E4 EILING MOUNT ( OTTOM PNEL ) 3/8 THREE STOK H1-H6 WLL MOUNT 3/8 5/16 X 2 1/2 G1-G4 FLOOR MOUNT 3/8 LEG GUIE ( PROVIE )/HILTI G1-G4 FLOOR MOUNT FOR SEISMI STTES 3/8 HILTI NHORS (3/8 X 3 1/2 ) NME TE O NOT SLE RWING TITLE: M-200 oilermate F RWN NELSON. WEIGHT: 77 LS ENG. SHMITT. WG NO. M PRO. HENSS M. MTERIL: 304 Stainless Steel SLES HNFOR J. REVISION 7/15/02 Q. MNGIN P.

6 Model HS-200 oiler Mate # Replacement Parts Item # Item escription Qty per unit Permeate Pump Membrane Filter Flow Restrictor 750 ml Gal Storage tank Filter Sediment 5 micron Filter arbon lock 5 micron Filter G/KF Filter alcite Valve heck 1/2" rass Valve all 1/2" rass HS-200 Unit PM Kit 1

7 HS-200 PT OM 1 OX-FILTERPK PK ROR SHEET WHT15.5 X ET GETIN E 2 OX-HS333 PK OX 28X28X26 FORHS E 3 OX-HS333-PLY PK HS333 PLYWOO INSERT E 4 FOM-HS333 PK FOM ORNER PS FORHS333 UNIT E W RO MOUNTING LIP SINGLE2 1/2" WHITE E 6 I061208W FTG 3/8-1/4 REUER WHITE E 7 ERP-1000 PUMP QUTE PERMETE PUMP UP TO 100 GP/NON ELE E 8 F N-O FTG JO MLE ONNETOR 1/4" NUT X 3/8" MNPT E 9 F SE-5M-Q SERIES Q/-14" E 10 F KF HS-333 Q-SERIES-14" E 11 F HOUSING-LI-Q SER-3/8"F-VLV H E 12 F ROM GP MEMRNE E 13 F TEE-PL-M-RUN-3/8MPTX1/ E 14 F EL-1/4FQX1/4MQ-PLSTIWHITE E 15 F RO HEK VLVE FOR MNIFOL E 16 F TNK PRESSURE (RP-5) E 17 F FLOW RESTRITOR-750ML/M-ST E 18 F SLEEVE-ELRIN-1/2-PL E 19 F INSERT-R-1/ E 20 F HEX NIPPLE-R-1/2MX1/4M-REUR E 21 F ON-R-1/2X1/2M E 22 F ON-R-1/2X3/4M E 23 F EL-R-1/2x3/8M E 24 F EL-R-1/2X1/2M E 25 F TEE-R-1/2 LL E 26 F FTG ELOW R 3/4"F X 3/4"F E 27 F PT-R-ULKHE-1/2F E 28 F VLVE-HEK-R-1/2F-# E 29 F VLVE-LENING 1/2"NPT E 30 F RKET-SINGLE-Q SERIES-14 G E 31 F FRME-M200 SS OX E 32 F P PLUG 8X- M E 33 F INSERT 1/ E 34 F OLT-OME-1/4-20x1/2"L-PHIL-SS E 35 F NUT-1/4-20 HEX FINISH STR LO E 36 F LEG-GLIE-1/ E 37 F NP GUGE PRESSURE/TEMP2.5 ENTER K MOUNT NO E 38 F PLUG-NYLON-LK-2.5" E 39 F MNUL-HS E 40 F STIKER OILER MTE E 41 F LELS-KIT-INFO-M /2X1/ E 42 F LEL-MEMRNE-GETINGE-GREEN# E 43 F LELS-KIT-FILT-#'S-HS E 44 F LEL-GETINGE-RINE & PERMETE SET

8 45 F LEL-FILTER-GET--LK-# E 46 F LEL-FILTER-GET-TS/PH-L-# E 47 F LEL-FILTER-GET-SE-RE E 48 F LEL-FILTER-GET-KF-6L-GL# E 49 F PH/TS LNER-Q SERIES-6" E 50 F FTG LL VLVE RSS 1/2"FXF E 51 FMPE-14-L-500 TU FLOWMTI 1/4" P.E. TUING LUE 500FT ROLL 52 I35216P-6 PL NIPPLE HEX RSS.375" 25/X E 53 I35216P-8 PL NIPPLE HEX RSS.50"10/X E 54 I352200P-6-6 PL ELOW RSS.375" FXF PRKER E 55 I352203P-4 PL TEE RSS.25" FXFXF25/X PRKER E 56 I352203P-6 PL TEE RSS.375" FXFXF PRKER E 57 I352203P-8 PL TEE RSS.50" FXFXFPRKER E 58 I8080 TUING POLYETHYLENE.50"O L LK PER 100' ROLL 59 JG W/MRT TGI-MLE RUN TEE 1/4OX1/4OX1/4NPT WHITE E 60 JG W/3 FTG REUING RNH TE E3/8X3/8X1/4 IMPORT P 61 JG W/3 TGI-PUSH IN FIXE ELOW 1/4"TX1/4,NPT WH P 62 JG W/3 TGI-PUSH IN FIXE ELOW 3/8"T X 3/8,NPT WH P 63 MH-200WL/3 TGI-MEMRNE HOUSING WHITE SIE PORT 1/8"NPT P 64 MS1034 FTG MOUNTING SREW #10X3/4" FOR 4000/4200 SERIES S E 65 N-O-4W FTG JO OMPRESSION NUT1/4" NUT/WHITE E 66 NMSSS8 OLT NUT HEX SS 8/ E 67 PE-08-I-0500F TU 1/4 INH TUE (500FTROLL) LUE ROLL 68 PE-08-I-0500FE TU 1/4 Inch Tube (500ftRoll)LK ROLL 69 PE-08-I-0500FG TU 1/4 Inch Tube (500ftRoll)GREEN ROLL 70 PE-12-EI-0500FN TU 3/8 Inch Tube (500ftRoll)NTURL ROLL 71 PI1808R FTG 1/4 LOKING LIP RE E 72 PI1812R FTG 3/8 LOKING LIPRE E 73 PP301208W FTG 3/8-1/4-3/8 REUING RN WHITE E 74 PP-1000 PRT PERMETE PUMP LIPFOR ERP E 75 Q5721 R - Q SERIES REPLEMENT FILTER 2 1/2" X 14"/10U E 76 R SS OLT N HEX P SREW.25"NX.75" 18-8SS E 77 R1914F-SS OLT WSHER FLT.25" 18-8SS E 78 R1914SN-SS OLT NUT LOK NYLON INSERT.25"N 18-8SS E 79 R19832SN-SS OLT NUT LOK NYLON INSERT SS E 80 W-ME0402 ELOW MLE 1/4"TUE X 1/ E

9 HS-200 Quarterly PM Maintenance Procedure: Figure 1 Remove Front Panel Figure 2 Remove 3 prefilters Figure 3 Remove alcite feeder 1. Remove eight screws from front panel (figure 1). Remove front panel, 2. Unscrew first stage sediment filter by grasping and turning counter clockwise (Figure 2) (No need to turn off incoming water source) discard, unscrew remaining filters and discard. 3. Install new filters by removing yellow cap (figure 3).on top and inserting each filter into corresponding element head. Insure all filters are hand tight and listen for permeate pumps to begin pulsating, check for leaks 4. Secure front panel. full one-year supply of filters is supplied with system upon installation. fter one year of service the HS-200 will need to have an annual PM kit ordered # this kit will include one full year supply of pre-filters and three replacement membranes. ustomer Service Toll Free Hot Line: W. Williams r. -20 Phoenix, Z 85027

10 Membrane replacement: Performed every year after the first year in service. nnual PM Procedures: Follow quarterly PM procedures as described above. 1. Remove top and front panels 2. Remove 3 prefilters and post calcite feeders (O NOT REPLE WITH NEW FILTERS T THIS TIME) 3. Remove 3 Reverse Osmosis Membranes (figure 5) 4. Replace with new membranes provided in PM kit # Replace 3 prefilters and PH alancer. Installing these filters will turn the water supply on to the unit and start production of water. Figure 4 Figure 5 Figure 6 Remove eight screws from front panel. Remove front panel. Remove first stage filter to shut down incoming water flow to system. rain the tank of boiler feed water by performing a blow down on the boiler. fter tank has been completely drained, disconnect the membranes by pressing in on the collets around the colored tubing (figure 6) to the membrane and pull. Each membrane should be removed one at a time insuring proper placement of tubing in corresponding color coded ports. Re-tighten first stage filter to start water flow, listen for permeate pumps to begin pulsating and check for leaks then secure panel. y passing the unit: The HS-200 unit can be placed into by pass if for some reason the equipment has failed and or has clogged filters. To by pass the RO system, open top panel by removing eight screws (figure 7)and open ½ brass Watts ball valve (figure 8) for tap water by-pass. fter service has been achieved close the Watts ball valve and wait for the system to begin permeating. Figure 7 Figure 8 ustomer Service Toll Free Hot Line: W. Williams r. -20 Phoenix, Z 85027

11 Series 1170, L1170 Hot Water Temperature ontrol Valves Size: 1h'\ % 11, 1 11 (15, 20, 25mm) Installation Instructions Valve should be installed and adjusted by a licensed contractor in accordance with local codes and ordinances. Further, this valve should be Installed in a location where it is accessible for cleaning, service or adjustment. 1. lose both the hot and cold water shutoff valves upstream nearest to the intended installation. 2. leed the remaining water from the system. 3. onnect the water supply to valve as shown in Flgure 1 or 2, depending on the application. Supply piping must be flushed clean before making connections to the valve. IMPORTNT!: To prolong the life of the Model 1170-M2, L1170-M2 valve, it is recommended that it be trapped as shown: I.e. t11e hot water inlet to the 1170-M2 valve should be 8" - 12" ( mm) below the hot water supply feed. 4. Valve can be installed in any position. Note: the inlet hot supply is to be connected to the "H" side of the valve, the cold supply side to the "" side and the mixed water outlet to the "M" side. ~ 5. Make sure union nuts are placed over tailpieces prior to '~ soldering or threading to pipe. 6. For valves with Quick-onnect tailpieces refer to "Quick onnect Installation" instructions below. Note: To prevent damage to valve from excessive heat during soldering, remove unions and gaskets from valve body prior to ~ soldering. 7. fter soldering, flush piping and install valve using filter washer on hot and cold water inlet and fiber washer on the mixed water outlet. 8. Start-up: Open cold water supply, then hot water supply. Inspect for leaks. 9. djust temperature to desired setting (see Temperature djustment Section). ( 1170-Q-M2 Quick-onnect Installation To onnect 1 1 /: In. {J.lmm) - -:-t '" ln.plpop2.7mm) 1'1 In. (44.45mm) 'ld :1 Pojl!! ( J) 1'/1 In. (47.63mm) 1 In.Pipe {25.4mm) 1. Mark ~ipe as shown. This is pipe insertion depth. / / IS-1170-M2_L 1170-M UT-M2 2. lean pipe end. Figure 1 omestic Hot Water pplication WattsT&P Relief Valve i + u!!! (I) a. E ~ a -12 I 1170-M2, L 1170 M2 PEX tubing only 3. If using PEX tubing, insert pipe s1kfener (proyided) into end of pipe. lo isconnect /ollolcllp ~ ---- ', -.. t Mark 4. Push tubing into!&piece up to mark. 5. Insert collet clip. l - - I u_~::::::::~-old omestic Hot Water pplication Note: To prolong the life of the valve, it is recommended the valve be trapped as shown evices tested!o SSE Standard 1016 such as Watts USG, L 111 or MMV should be used at fixture to prevent possible injury. \ olle! depll?ss!hf 1. Remove collet clip. 2. epress collet. 3. Pull tubing from tailpiece. WWMI IS

12 Figure 2 Radiant Heat pplication o 11.' all Valve ""\'f..e oie.~,,...,., \0 \'.\'i Period Inspection/Maintenance Tl1is valve requires periodic inspection and verification of the outlet temperature by a licensed contractor. orrosive water conditions, hot inlet water temperature over 200 F (93 ), unauthorized adjustments or repairs could render the valve ineffective for its intended service. Regular cleaning and checking of thermostat assembly helps to maximize valve life and mixing function. Frequency of cleaning depends on local water conditions. i. to oiler Figure 3 Temperature djustment Factory Preset: 1 ~. 170-M2: 120 F (49 ) L 1170-M2: 90 F (31 ) Un.der following conditions: old Inlet: F (16-21 ) Hot Inlet: F (60-63 ) $upply Pressure: 45psi (3.15 bar) Pressure - Temperature Minimum Supply Pressure (Static): 30psi (207 kpa) Inlet Temperatures: hot inlet, 120 F F (49-93 ), cold inlet, 40 F - 5 F (4-29 ) Hot Water Inlet to Outlet ifferential Temperatwe: 5 F (3 ) 1170-M2 Temperature Out: Field range: 90 F F (32-71 ), adjustable. ccurate within ±3 F (1.7 ) L 1170-M2 Temperature Out: Field range: 60 F F (16-49 ), adjustable. ccurate within ±3 F (1.7 ) Maximum Temperature: 200 F (93 ) Maximum Pressure: 150psi (10.3 bar)._. pproval: S 8125 certified Listing: SSE 1017,, 3 /32" Hex Wrench ~ Unscrew, lift cap to adjust 1. Let water flow for at least two minutes to allow supply temperature to stabilize. 2. alibrate the mixed water outlet temperature by placing a thermometer in the mixed water stream. 3. To adjust the setting of the valve, loosen locking cap screw with hex wrench, see Figure 3. ap must be lifted 1/4" to adjust temperature. To increase the temperature, turn counterclockwise. To decrease temperature turn clockwise. 4. Lower handle and tighten screw. 5. heck outlet temperature. l twrnlng Watts Hot Water Temperature ontrol Valves cannot be used for tempering water tempera~e at fixtures. Severe bodily injury O.e. scalding or chilling) and/or dej;th may result depending upon system water pressure changes. SSE Standard 1016, SSE 1070 listed devices such as Watts Model L 111 or Series USG, or MMV should be used at fixtures to prevent possible injury. The Watts Hot Water Temperature ontrol Valves are designed to be inslalled at or near the boiler or water heater. They are not designed to compensate for system pressure fluctuations and should not be used where SSE 1016 devices are required. These WTIS valves should never be used to provide "anti-scald" or 'anti-chill" service. When installing the Series 1170-M2 valves in a radiant heat ilpplicatlon, the components of the radiant heat system must be of materials with a construction capable of wilhstanding the high fimlt output temperatures of the heating boiler. If you are uncertain as to the product's adaptability for your application, please consult an authorized representative before installing or using the product. I " < r'

13 Watts 1170-M2, L 1170-M2 Troubleshooting Guide Problem & ause nswer ~ Unaqle tp reach required sel point or set polnl difficult to set.1 Supply temperatures not within specified llmit!;? Hot and cold supplies reversed.3 Filters are blocked by pebris.1 heck di_fferential temper(!ture betwe_en hpt and cold supplies and outlet 10 F (5.6 ) minimum required.2 Reinstall valve with supplies connected to marked inlets.:,3 lean filters 8. Unable to achieve required flow 8.1 Too much pressure drop at fixture 8.2 hecks valve/filters blocked by debris 8.1 Measure supply pressures and check against flow chart. Look for restrictions in valve or piping- 8.2 lean check valves/filters. Valve does not maintain required temperature or temperature changes over time c.1 Fluctuation in supplx pressures.2 heck valve/fillers bl~cked by debris.3 Recirculation loop not piped properly :o. ischarge temperature loo hot or cold 0.1 Valve not calibrated properly.1 Stabilize water pressures with pressure re!;julatlng or balancing valves.2 lean check valves/fili-ers.3.pipe recirculated tempered water return so ii connects to hot water so~irce and cold side of mixing valve (see Product Guide for piping details) : 1! 0.1 Readjust valve temperature per installation instruclions ~ Hot water from cold water tap or cold from hot ' E.1 heck valves fouled E.1 lean check valves/filters F. Valve is noisy F.1 Water velocity is too high F.2 Valve not sized properly ~ No flow from valve G.1 Hot or cold water supply failure or shutoffs closed G.2 heck valve/filters block~d by debris H. Flow from valve fluctuates H.1 Fluctuation in supply pressures H.2 heck valve/filters blocked by debris r F.1 Reduce water velocity wilt) i;iressure regulating valves F.2 heck flow, required versus rated flow capacity of valve G.1 Open shutoffs or restore hot and cold supply G.2 lean check valves and filters H.1 Stabilize water pressure with pressure regufating valves H.2 lean check valves and filters

14 r I I TTENTION INSTLLER: fter installation, please leave this Instruction Sheet for occupant's information. IMPORTNT: Inquire with governing authorities for local installation requirements. WRNING! For valves with PV or PEX end connections do not exceed the tubing manufacturers pressure and temperature ratinps. Refer to the tubing manufacturers product specifications for that information. LIFORNI PROPOSITION 65 WRNING WRNING: This product contains chemicals known to the State of alifornia to cause cancer and birth defects or other reproductive harm. (alifornia law requires this warning to be given to customers In the State of alifornia.) For more inlonnalion: Umited Warranty: Watts Regulator ompany warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of o rl,~al shipment In the event of such defects wilhin the warranty period, Uie ompany will, at Its option, replace or recondition tile product witllout charge. This shall constitute the solo and exclusive remedy for breach of warranty, and Uie ompany shall not be responsible for any incidental, special or consequential damages, Including without llmltatlon, lost profits or the cost of repairing or replacing other property which Is damaged If this product does not work properly, othor costs resulling from labor charges, delays, vandalism, negligence, fou ling caused by foreign materlal, damage from adverse water conditions, chemical, or any other circumstances over which the ompany has no control. This warranty shall be invalidated by any abuse, misuse, misapplication or Improper installation of the product THIS WRRNTY IS IN LIEU OF ll OTHER WRRNTIES, EXPRESS OR IMPLIE, fnwing NY IMPLIE WRRHTJES OF MERHNTILITY OR TNESS FOR PRTIULR PURPOSE. ny lmpoed warranties that are imposed by law are 6mlled In duration to one year. Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow tile exclusion or limitation or Incidental or consequential damages. Therefore the above limitations may not apply to you. TI1ls limited Warranty gives you specific legal rights, and you may have otlrnr rights that vary from State to State. You should consult applicable state laws to determine your rights. WWMI IS Water Safety & Flow ontrol Products IS-1170-M2_L 1170-M ETmFIE US: l 5 hestnut St., No. ndover, M : anada: 5435 North Service Rd., urlington, ONT. L7L 5H7; EP/I Watts Regulator o., 2007