E3G-L1/L3. Effectively Cuts the Influence of Workpiece Characteristics, Such as Gloss, Incline, and Color. Distance-setting Photoelectric Sensor

Transcription

1 Distance-setting Photoelectric EG-L/L CSM_EG-L_L_DS_E Effectively Cuts the Influence of Workpiece Characteristics, Such as Gloss, Incline, and Color. Be sure to read Safety Precautions on page. Features A -mm-dia. Pin-point Beam Allows Detection of Minute Objects Smallest in the Industry EG-L OMR's unique Hyper LED achieves a pinpoint light source only /7 the size of conventional light sources, with uniform light-intensity distribution. The Hyper LED achieves stable detection of small objects by eliminating the dead band that results from the drop-out that commonly occurs at the center of conventional LEDs. The clearly visible spot makes it easy to check the optical axis adjustment and sensing position. Stable Detection Based Not Only on Object Color, But Also on and Glossiness The EG-L is. times more stable than previous models with inclination characteristics. The use of the shine-proof optical system with conventional triangulation reduces the discrepancies in sensing distance due to object color, surface, and inclination. (The EG-L is. times more stable than previous models.) Shine-proof Optical System (EG-L, EG-L) First in the Industry Previous Distancesetting Models OK Distance fluctuation detected due to slight lifting. NG (Lifting of IC) Intensity Light source LED PSD A low-error distance signal is assured because an image is formed on the photosensing device (PSD), irrespective of the sensing distance. Detection is also stable with respect to the inclination of the object. Error Center of gravity Intensity Light source LED PSD At some distances, images cannot be formed on the photosensing device (PSD). The spot diameter is large, distance errors occur due to displacement of the center of gravity, and detection is unstable with respect to the inclination of the object.

2 EG-L/L Simple Detection of Glossy, Uneven Objects Normal Mode Threshold (light) Conveyor (background) (dark) Triangulation with hysteresis of % or less (EG-L) is used, so objects beyond the set distance are not detected. At a set distance of mm, steps that are. mm high can be detected. Selectable IP7 Waterproofing CE Marking (dark) Threshold (light) Threshold First in the Industry Zone Mode Conveyor (background) (dark, when dark is set for ) Glossy, uneven objects are reliably detected because (light) status occurs only when the conveyor is detected, and (dark) status occurs when an object is present. The meets the European EMC Directive, allowing it to be mounted in export devices with confidence. Optimal and Conveyor Teaching. Double-bar Display Shows Excess Gain at a Glance. The features onetouch teaching settings. After the workpiece, background, and conveyor teaching are complete, fine adjustment of the sensitivity can be made in levels for Normal Mode or levels for Zone Mode. The excess gain in distance or detecting of small steps can be easily set. A Lineup of M8 Connectors Easy to disconnect, making maintenance simple. The operation indicator turns when the light incident level exceeds a certain threshold. Excess gain can also be checked at a glance. Straight L-shaped Meets the Needs of All Industries, Including Semiconductors, Electronic Components, Food, and Packaging Normal Mode EG-L (-mm Models) Detecting minute electronic components in a tray Detecting thin or uneven objects EG-L (-mm Models) Detecting objects on a production line with a glossy background IC No packaging Zone Mode EG-L (-mm Models) Detecting packaged candies Detecting tiles on a conveyor EG-L (-mm Models) Detecting packaged confectionery on a conveyor Glossy wrapping Glossy wrapping

3 Ordering Information s Appearance Connection method Sensing/Setting range Operation mode Red light EG-L/L Infrared light Model NPN output PNP output Pre-wired mm mm mm mm Min.setting Setting range: Max. setting to mm EG-L EG-L Connector (M8) Sensing range: to mm Light Dark EG-L EG-L Pre-wired mm mm mm mm (selectable) Setting range: Min.setting to mm for white EG-L EG-L Connector (M8) Sensing range: EG-L EG-L to mm for white Accessories (Order Separately) Mounting Brackets Max.setting Appearance Model Quantity Remarks E9-L9 Provided with the EG-L@/-L@ E9-L Provided with the EG-L@/-L@ I/O Connectors (M8) Cable specifications Appearance Cable type Model Straight m XSF-M--A Standard Cable m Four-wire XSF-M--A L-shaped m type XSF-M--A m XSF-M--A

4 Ratings and Specifications EG-L/L Item Sensing method Model Sensing range Setting range NPN output PNP output Distance-setting EG-L EG-L EG-L EG-L EG-L EG-L EG-L EG-L to mm ( mm white, setting distance: mm) to mm ( mm white, black ) to mm ( mm white, setting distance: mm) to mm ( mm black, setting distance: mm) to mm ( mm white ) to mm ( mm black ) Differential travel % max. of setting distance % max. of setting distance (typical) Reflectivity characteristics (black/white error) Light source (wavelength) % max. of setting distance Red LED (7 nm) % max. of setting distance (at to -mm setting distance) Infrared LED (8 nm) Spot size -mm dia. max. (at 8-mm sensing distance) -mm dia. max. (at -mm sensing distance) Power supply voltage to VDC including % (p-p) ripple Current consumption ma max. ma max. Control output Protection circuit Load power supply voltage: VDC max., Load current: ma max. (Residual voltage: NPN output:. V max., PNP output:. V max.) Open collector output (NPN/PNP, depends on the model) Light /Dark selectable Power supply reverse polarity protection, Load short-circuit protection, Mutual interference prevention Response time Operate or reset:. ms max. Operate or reset:. ms max. Distance setting Indications Ambient illumination (Receiver side) Ambient temperature Ambient humidity Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Degree of protection Connection method Teaching (in NORMAL or ZE mode) Manual fine threshold adjustment (NORMAL mode: levels, ZE mode: levels) Operation indicator, Distance indicator (green: 8 levels), Threshold indicator (red, NORMAL mode: levels, ZE mode: levels) Incandescent lamp:, lx max., Sunlight:, lx max. Operating: C to C, Storage: C to 7 C (with no icing or condensation) Operating: % to 8%, Storage: % to 9% (with no condensation) MΩ min. at VDC, VAC, /Hz for min to Hz,.-mm double amplitude for hours each in X, Y, and Z directions m/s times each in X, Y, and Z directions IEC IP7 (with protective cover) Pre-wired (Standard length: m) Connector (M8) Pre-wired (Standard length: m) Connector (M8) Weight (packed state) Approx. g Approx. g Approx. g Approx. g Case PBT (polybutylene terephthalate) Fine distance adjustment Cover Accessories Mounting Bracket Methacrylic resin Stainless steel (SUS) Mounting Bracket (with screws), Instruction sheet

5 Engineering Data (Typical) EG-L/L Operating Range Spot Diameter vs. Sensing Distance (in NORMAL Mode) (in ZE Mode) Operating range Y (mm) Setting distance: mm, mm, mm Sensing object: White, mm mm Operating range Y (mm) Setting distance: mm mm mm mm mm Spot diameter (mm). mm X Y. mm mm. Distance X (mm) Distance X (mm) EG-L@ (in NORMAL Mode) EG-L@ (in ZE Mode) EG-L@ Operating range Y (mm) Setting distance: mm, mm, mm Sensing object: White, mm mm X Y Operating position Y (mm) Setting distance: mm, mm, mm mm Spot diameter (mm) Distance (mm) 8 mm mm mm mm Angle Characteristics Distance X (mm) Distance X (mm) EG-L@ (Vertical) EG-L@ (Horizontal) EG-L@ Sensing object: White, mm Sensing distance: mm Vertical +θ θ Sensing object Center line (θ) Sensing object: White, mm Sensing distance: mm Vertical +θ θ Sensing object Center line (θ) EG-L@ (Vertical) EG-L@ (Horizontal) EG-L@ Sensing object: White, mm Sensing distance: mm Sensing object: White, mm Sensing distance: mm 8 8 Distance (mm) Sensing Object Size vs. Setting Distance Min. sensing object dia. (mm) Min. sensing object dia. (mm)..... Sensing object: Stainless steel rod Setting distance: white, mm Distance (mm). Sensing object: Stainless steel rod Setting distance: white, mm. (Vertical) Sensing object Center line (θ) (Horizontal) +θ θ Sensing object Center line (θ). 8 8 Distance (mm)

6 EG-L/L Angle Characteristics Close-range Characteristics (Vertical) (Horizontal) 8 Sensing object: White, mm Sensing distance: mm Vertical +θ θ 8 Sensing object Center line (θ) 8 Sensing object: White, mm Sensing distance: mm Horizontal +θ θ 8 Sensing object Center line (θ) EG-L@ (Vertical) EG-L@ (Horizontal) EG-L@ 8 Sensing object: White, mm Sensing distance: mm Sensing object Center line Vertical (θ) Sensing object: White, mm 8 Sensing distance: mm mm White White Sensing Distance vs. Sensing Object EG-L@ (at -mm Setting Distance) EG-L@ (at -mm Setting Distance) EG-L@ (at -mm Setting Distance) Horizontal +θ θ 8 Sensing object Center line (θ) Setting distance: mm Setting distance: mm mm mm 8 mm mm mm mm mm Setting distance: mm Setting distance: mm mm 78 mm mm 8. mm 8. mm 9 mm mm White White mm White Veneer Fiberboard rubber Mirror White Veneer Fiberboard rubber Mirror White Veneer Fiberboard rubber Mirror EG-L@ (at -mm Setting Distance) EG-L@ (at -mm Setting Distance) EG-L@ (at -mm Setting Distance) White Veneer Fiberboard rubber Mirror White Veneer Fiberboard rubber Mirror White Veneer Fiberboard rubber Mirror

7 I/O Circuit Diagrams EG-L/L NPN Output Model Operation mode Timing charts Mode selector switch Output circuit EG-L EG-L EG-L EG-L Light- Dark- Incident light No incident light Operation indicator Output transistor Load Operate (e.g., relay) Reset (Between brown and black) Incident light No incident light Operation indicator Output transistor Load Operate (e.g., relay) Reset (Between brown and black) L- (LIGHT ) D- (DARK ) 8-level -level distance threshold indicator indicator (green) (red) Operation indicator Photoelectric main circuit Brown to VDC NPN output transistor Load Control ma output max. ZD Blue Connector Pin Arrangement V Note: Pin is not used. PNP Output Model Operation mode Timing charts Mode selector switch Output circuit EG-L EG-L EG-L EG-L Light- Dark- Incident light No incident light Operation indicator Output transistor Load (e.g., relay) Operate Incident light No incident light Operation indicator Output transistor Load (e.g., relay) Reset (Between blue and black) Operate Reset (Between blue and black) L- (LIGHT ) D- (DARK ) 8-level -level distance threshold indicator indicator (green) (red) Operation indicator Photoelectric main circuit Connector Pin Arrangement ZD PNP output transistor Brown to VDC Blue ma max. Control output Load V Note: Pin is not used. Plugs ( I/O Connectors) Pin No. XSF-M--A XSF-M--A XSF-M--A XSF-M--A Wire colors Blown White Blue Classification Wire color Connector pin No. Application Blown Power supply (+ V) DC White --- Blue Power supply ( V) Output Note: Pin is not used. Nomenclature UP/DOWN selector switch Selects the switching direction at threshold. Operation indicator Lit when output is. Distance indicator (green) Displays the distance relative to the threshold. Threshold indicator (red) Indicates threshold level. SET button Used for teaching or for threshold adjustment. ZE D Operation mode selector switch Selects L- or D-. NORMAL/ZE selector switch Selects the detection mode. Mode selector switch Selects the mode. 7

8 Adjustments EG-L/L Adjustment Procedure Step Operation Install, wire, and turn the. Perform distance setting (teaching). Refer to Distance Setting (Teaching), below. Make a fine adjustment of the threshold, if necessary. Refer to Manual Teaching (Fine Distance Setting). Page Check that the mode selector switch is set to. Distance Setting (Teaching) Select the most appropriate teaching method in reference to the following descriptions. Application Teaching without sensing objects (i.e., teaching the background). Detection of slight differences in surface level. Setting a threshold in the middle between the background and sensing object for operation. Detection of glossy objects in front of the background. Teaching Normal one-point teaching Normal two-point teaching Zone one-point teaching Setting method TEACH Press the background object. button with the TEACH Press the button with the background object and with the sensing object. TEACH Press the button with the background object (conveyor, etc.). Object Set threshold Threshold (a) is set immediately in front of the background. Threshold (a) is set approximately in the middle between the background and sensing object. A pair of thresholds, (a) and (b), are set. The output is between the and La. The output is between the and La. The output is between La and Lb. EG-L EG-L D- L- EG-L Output range Threshold a (La) Threshold a (La) Threshold a (La) Threshold b (Lb) La: Distance equivalent to threshold (a) Lb: Distance equivalent to threshold (b) The following settings are also possible: Setting the maximum sensing distance of the : Maximum distance setting. Setting the minimum differential travel of the : Minimum distance setting. Distance from to background must not exceed the values shown below during normal one-point or zone one-point teaching. Model EG-L@ EG-L@ Distance from to background mm min. mm min. Maximum sensing distance of the EG-L@ may differ depending on the color of the sensing object when setting distance is more than mm. Confirm the operation of the before actual operation. 8

9 EG-L/L Normal One-point Teaching EG-L Threshold a (La) Step Operation Panel status Set the mode selector switch to TEACH. Set the NORMAL/ZE mode selector switch to NORMAL. Press the SET button with the background. ZE D The threshold indicator (red) will turn. Threshold indicator (red) turns. Set the mode selector switch to. Set to L- or D- mode with the operation mode selector switch. L-: Output between background and. D-: Output between background and. Press Application Example Adjusting the differential travel to the minimum distance. Set the mode selector switch to TEACH. Set the NORMAL/ZE mode selector switch to NORMAL. Set the UP/DOWN selector switch to DOWN. Press the SET button for at least s. The threshold indicator (red) will turn. The distance indicator (green) will turn. This means that teaching is successful. Set the mode selector switch to to complete the teaching operation. ZE D Press Press the SET button for s or more. Set the mode selector switch to. Set to L- or D- mode with the operation mode selector switch. (Refer to Normal One-point Teaching) Threshold indicator (red) turns. Distance indicator (green) turns. Application Example Setting the to the maximum distance. Set the mode selector switch to TEACH. Set the NORMAL/ZE mode selector switch to NORMAL. Set the UP/DOWN selector switch to UP. Press the SET button for s or more. The threshold indicator (red) will turn. The distance indicator (green) will turn. This means that teaching is successful. Set the mode selector switch to to complete the teaching operation. ZE D Press Press the SET button for s or more. Set the mode selector switch to. Set to L- or D- mode with the operation mode selector switch. (Refer to Normal One-point Teaching) La: Distance equivalent to threshold (a) Threshold indicator (red) turns. Distance indicator (green) turns. 9

10 EG-L/L Normal Two-point Teaching EG-L Object Object Threshold a (La) Step Operation Panel status Set the mode selector switch to TEACH. Object Set the NORMAL/ZE mode selector switch to NORMAL. Press the SET button with a sensing object located at sensing position. The threshold indicator (red) will turn. Move the sensing object and press the SET button with the background. If the teaching is successful, the distance indicator (green) will turn. If the teaching is not successful, the threshold indicator (red) will start to flash. If the teaching is successful, set the mode selector switch to to complete the teaching operation. If the teaching is not successful, change the position of the object and setting distance that have been set and repeat from the above step. Set to L- or D- mode with the operation mode selector switch. ZE D Press ZE D OK NG Threshold indicator (red) turns. Distance indicator (green) turns. Threshold indicator (red) starts to flash. Press La: Distance equivalent to threshold (a) Zone One-point Teaching EG-L Threshold a (La) Threshold b (Lb) Step Operation Panel status Set the mode selector switch to TEACH. Set the NORMAL/ZE mode selector switch to ZE. Press the SET button with the background. All threshold indicators (red) will turn OK while the SET button is pressed. When the SET button is released: ZE D If the teaching is successful, the distance indicator (green) will turn. If the teaching is not successful, the threshold indicator (red) will start to flash. Set the mode selector switch to. Set to L- or D- mode with the operation mode selector switch. L-: Output with the background. D-: Output with the background. La: Distance equivalent to threshold (a) Press NG Distance indicator (green) turns. Threshold indicator (red) starts to flash.

11 EG-L/L Manual Teaching (Fine Distance Setting) Step Operation Panel status Fine adjustment of the threshold is possible after teaching. Set the mode selector switch to. Set the adjustment direction in the mode with the UP/DOWN selector switch. The threshold changes each time the SET button is pressed. The setting can be made in up to levels (for normal one-point or two-point teaching). After the adjustment is complete, set the mode selector switch to. ZE D Press SET pressed with UP/ DOWN selector switch set to UP. SET pressed with UP/ DOWN selector switch set to DOWN. Threshold increases. Threshold decreases. Threshold Indicator Display during Distance Adjustment Max. adjustment levels for normal teaching. Level Threshold indicators Five adjustment levels for zone teaching. Threshold indicators Level Threshold and Distance Indicator Displays Display for Distance Setting with Normal One-point or Two-point Teaching The distance indicators show the distance level. The distance indicators show distances relative to the threshold. The threshold can be shifted using the UP/DOWN selector and SET button. The differential travel cannot be changed. Display for Distance Setting with Zone Teaching The distance indicators show the current distance band. The distance indicators show distances relative to the threshold. The range can be shifted using the UP/DOWN selector and SET button. The differential travel cannot be changed. UP UP Control output: UP UP Control output: DOWN DOWN DOWN (No change) Control output:

12 Safety Precautions WANINNG This product is not designed or rated for ensuring safety of persons. Do not use it for such purpose. Precautions for Correct Use Do not use the product in atmospheres or environment that exceed product ratings. Wiring Cable The bending radius of the cable must be no smaller than mm. Avoiding Malfunctions If using the Photoelectric with an inverter or servomotor, be sure to ground the FG (frame ground) and G (ground) terminals, otherwise the may malfunction. Mounting Mounting Conditions If s are mounted face-to-face, make sure that no optical axes cross each other. Otherwise, mutual interference may result. Be sure to install the carefully so that the directional range of the will not be directly exposed to intensive light, such as sunlight, fluorescent light, or incandescent light. Do not strike the Photoelectric with a hammer or any other tool during the installation of the, or the will loose its water-resistant properties. Use M screws to mount the. When mounting the case, make sure that the tightening torque applied to each screw does not exceed. N m. M8 Connector Always turn the before connecting or disconnecting the M8 connector. Be sure to hold the connector cover when connecting or disconnecting the M8 connector. Secure the M8 connector by hand. Do not use any pliers, otherwise the connector may be damaged. If the M8 connector is not connected securely, the M8 connector may be disconnected by vibration or the proper degree of protection of the may not be maintained. Mounting Directions Make sure that the sensing side of the is parallel with the surface of each sensing object. Do not incline the towards the sensing object. If the sensing object has a glossy surface, incline the by to as shown below, provided that the is not influenced by any background objects. Sensing side Surface of sensing object EG-L/L If there is a mirror-like object below the, the may not be in stable operation. Therefore, incline the or keep the a distance away from the mirrorlike object as shown below. Make sure not to install the in the incorrect direction. Refer to the following. Sensing object Sensing object Moving direction Mirror-like object Sensing object Moving direction Install the as shown in the following if each sensing object greatly differs in color or material. Moving direction Sensing object Moving direction Moving direction Adjustments If the is not in stable operation due to color differences, make a fine adjustment of the threshold level and confirm that operation is stable. Refer to Manual Teaching (Fine Distance Setting) Page Maintenance and Inspection Cleaning Paint thinner will damage the casing of the. Do not use paint thinner to clean the. Others EEPROM Writing Error If a teaching data error occurs with the operation indicator flashing due to a power failure or static noise, perform the teaching operation of the again. Water Resistivity To ensure the water resistivity of the, tighten the screws of the operation panel cover to a torque of. to. N m. Glossy object

13 EG-L/L Dimensions s (Unit: mm) Unless otherwise specified, the tolerance class IT is used for dimensions in this data sheet. Pre-wired Models EG-L/L EG-L/L With Mounting Bracket Attached. *A Two, R. Two, M. Distance indicators (green) Operation indicator 8 Threshold indicators (red) M. 7. * Mounting Bracket can be attached to side A Two, M Mounting Holes Two, 8-dia. lens Emitter 8. A* 7 Two, M through holes. Six, R. Optical axis Receiver B*. Two,. dia.. dia. -dia. (8/. dia.) vinyl-insulated round cable with three conductors, Standard length: m. 9. * Model A B EG-L@..88 EG-L@. Connector Models EG-L/L EG-L/L With Mounting Bracket Attached *A Two, M Two, R. 9.. Mounting Holes Distance indicators (green) Operation indicator 8 Threshold indicators (red) M.. * Mounting Bracket can be attached to side A Two, M Two, 8 -dia. lens Emitter 8. 7 Two, M through holes Six, R. A*. Two,. dia. 7. Optical axis Receiver B* dia. M8 Connector. * Model A B EG-L@..88 EG-L@. Accessories (Order Separately) Mounting Brackets In the interest of product improvement, specifications are subject to change without notice.

14 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMR's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMR. OMR MAKES NO WARRANTY OR REPRESENTATI, EXPRESS OR IMPLIED, REGARDING N-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMR DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIS OF LIABILITY OMR SHALL NOT BE RESPSIBLE FOR SPECIAL, INDIRECT, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED CTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMR for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMR BE RESPSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMR'S ANALYSIS CFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CTAMINATI, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATI OR REPAIR. Application Considerations SUITABILITY FOR USE OMR shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMR will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITH ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMR shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMR representative at any time to confirm actual specifications of purchased products. DIMENSIS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMR s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMR Warranty and Limitations of Liability. ERRORS AND OMISSIS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. OMR Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation 8 All Right Reserved.

15 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: E9-L9 E9-L EG-L