Standard Pump SPFP30. Service & Operating Manual. 3" Food Processing. Original Instructions. SPFP30 Models SPFP30NPT SPFP30NPS SPFP30SSS SPFP30SST

Transcription

1 Standard Pump Service & Operating Manual Original Instructions 3" Food Processing SPFP30 Models SPFP30NPT SPFP30NPS SPFP30SSS SPFP30SST SPFP30 STANDARD PUMP, INC 1610 Satellite Blvd Suite D. Duluth, Ga Phone: (770) : CERTIFICATES 3: EXP VIEW 2: INSTAL & OP 1: PUMP SPECS

2 Safety Information IMPORTANT WARNING Read the safety warnings and instructions in this manual before pump installation and start-up. Failure to comply with the recommendations stated in this manual could damage the pump and void factory warranty. When the pump is used for materials that tend to settle out or solidify, the pump should be flushed after each use to prevent damage. In freezing temperatures the pump should be completely drained between uses. CAUTION Before pump operation, inspect all fasteners for loosening caused by gasket creep. Retighten loose fasteners to prevent leakage. Follow recommended torques stated in this manual. Nonmetallic pumps and plastic components are not UV stabilized. Ultraviolet radiation can damage these parts and negatively affect material properties. Do not expose to UV light for extended periods of time. WARNING Pump not designed, tested or certified to be powered by compressed natural gas. Powering the pump with natural gas will void the warranty. When used for toxic or aggressive fluids, the pump should always be flushed clean prior to disassembly. Before maintenance or repair, shut off the compressed air line, bleed the pressure, and disconnect the air line from the pump. Be certain that approved eye protection and protective clothing are worn at all times. Failure to follow these recommendations may result in serious injury or death. Airborne particles and loud noise hazards. Wear eye and ear protection. In the event of diaphragm rupture, pumped material may enter the air end of the pump, and be discharged into the atmosphere. If pumping a product that is hazardous or toxic, the air exhaust must be piped to an appropriate area for safe containment. Take action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers and other miscellaneous equipment must be properly grounded. This pump is pressurized internally with air pressure during operation. Make certain that all fasteners are in good condition and are reinstalled properly during reassembly. Use safe practices when lifting kg Grounding the Pump To be fully groundable, the pumps must be ATEX Compliant. Optional 8 foot long (244 centimeters) Ground Strap is available for easy ground connection. To reduce the risk of static electrical sparking, this pump must be grounded. Check the local electrical code for detailed grounding instruction and the type of equipment required. WARNING Take action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers or other miscellaneous equipment must be grounded.

3 Table of Contents SECTION 1: PUMP SPECIFICATIONS...1 Performance Materials Dimensional Drawings SECTION 2: INSTALLATION & OPERATION...4 Principle of Pump Operation Typical Installation Guide Troubleshooting SECTION 3: EXPLODED VIEW...7 Composite Drawings Parts List Materials Code SECTION 4: CERTIFICATES...11 EC Declaration of Conformity - Directive 2006/42/EC - Machinery EC Declaration of Conformity - Directive 94/9/EC - ATEX EC Declaration of Conformity - Directive 1935/2004/EC - Food Contact Materials 4: CERTIFICATES 3: EXP VIEW 1: PUMP SPECS 2: INSTAL & OP

4 Performance 1: PUMP SPECS Model SPFP30NPS & SPFP30SSS 3" Clamped - Food Processing FDA SANTOPRENE FITTED Flow Rate Adjustable to gpm (886 lpm) Port Size Suction... 3" TRI-CLAMP Discharge... 3" TRI-CLAMP Air Inlet...1/2" NPT Air Exhaust... 1" NPT Suction Lift Dry...20' (6.1 m) Wet....32' (9.8 m) Max Solid Size (Diameter)... 3/8" (9.5 mm) Max Noise Level...96 db(a) Shipping Weights Stainless lbs (86 kg) ** Stainless Center add lbs. (22.7 kg) Meters Feet BAR Discharge Head in PSI Displacement Per Stroke, 1.36 Gal. (5.1 L) 180 AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI SCFM M 3 /HR Capacity in U.S. Gallons Per Minute Capacity in Liters Per Minute NOTE: Performance based on the following: PTFE fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%. Model SPFP30NPT & SPFP30SST 3" Clamped - Food Processing PTFE FITTED Flow Rate Adjustable to gpm (681 lpm) Port Size Suction... 3" TRI-CLAMP Discharge... 3" TRI-CLAMP Air Inlet...1/2" NPT Air Exhaust... 1" NPT Suction Lift Dry...12' (3.7 m) Wet....32' (9.8 m) Max Solid Size (Diameter)... 3/8" (9.5 mm) Max Noise Level...95 db(a) Shipping Weights Stainless lbs (86 kg) ** Stainless Center add lbs. (22.7 kg) Meters Feet BAR Discharge Head in PSI Capacity Per Stroke, 0.92 Gal. (3.5 L) AIR CONSUMPTION IN SCFM AIR PRESSURE IN PSI SCFM M 3 /HR Capacity in U.S. Gallons Per Minute Capacity in Liters Per Minute NOTE: Performance based on the following: PTFE fitted pump, flooded suction, water at ambient conditions. The use of other materials and varying hydraulic conditions may result in deviations in excess of 5%. 1 Model SPFP30 Food Processing

5 Materials Material Profile: CAUTION! Operating temperature limitations are as follows: Santoprene : Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance. Virgin PTFE: (PFA/TFE) Chemically inert, virtually impervious. Very few chemicals are known to chemically react with PTFE; molten alkali metals, turbulent liquid or gaseous fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at elevated temperatures. Operating Temperatures: Max. 275 F 135 C 220 F 104 C Min. - F - C -35 F -37 C Maximum and Minimum Temperatures are the limits for which these materials can be operated. Temperatures coupled with pressure affect the longevity of diaphragm pump components. Maximum life should not be expected at the extreme limits of the temperature ranges. Metals: Stainless Steel: Equal to or exceeding ASTM specification A743 CF-8M for corrosion resistant iron chromium, iron chromium nickel and nickel based alloy castings for general applicaitons. Commonly referred to as 316 Stainless Steel in the pump industry. 1: PUMP SPECS Model SPFP30 Food Processing 2

6 Dimensional Drawings Model SPFP30 Food Processing Dimensions in inches (metric dimensions in brackets). Dimensional Tolerance.125" (3mm) O.D. TRI- CLAMP DISCHARGE FLANGE : PUMP SPECS 1/2" NPT AIR INLET " NPT AIR EXHAUST O.D. TRI- CLAMP SUCTION FLANGE R BOTTOM VIEW 3 Model SPFP30 Food Processing

7 Principle of Pump Operation Air-Operated Double Diaphragm (AODD) pumps are powered by compressed air or nitrogen. The main directional (air) control valve 1 distributes compressed air to an air chamber, exerting uniform pressure over the inner surface of the diaphragm 2. At the same time, the exhausting air 3 from behind the opposite diaphragm is directed through the air valve assembly(s) to an exhaust port 4. As inner chamber pressure (P1) exceeds liquid chamber pressure (P2), the rod 5 connected diaphragms shift together creating discharge on one side and suction on the opposite side. The discharged and primed liquid s directions are controlled by the check valves (ball or flap)6 orientation. The pump primes as a result of the suction stroke. The suction stroke lowers the chamber pressure (P3) increasing the chamber volume. This results in a pressure differential necessary for atmospheric pressure (P4) to push the fluid through the suction piping and across the suction side check valve and into the outer fluid chamber 7. Suction (side) stroking also initiates the reciprocating (shifting, stroking or cycling) action of the pump. The suction diaphragm s movement is mechanically pulled through its stroke. The diaphragm s inner plate makes contact with an actuator plunger aligned to shift the pilot signaling valve. Once actuated, the pilot valve sends a pressure signal to the opposite end of the main directional air valve, redirecting the compressed air to the opposite inner chamber. 2: INSTAL & OP SUBMERGED ILLUSTRATION MUFFLER LIQUID LEVEL 1" DIAMETER AIR EXHAUST PIPING SUCTION LINE Pump can be submerged if the pump materials of construction are compatible with the liquid being pumped. The air exhaust must be piped above the liquid level. When the pumped product source is at a higher level than the pump (flooded suction condition), pipe the exhaust higher than the product source to prevent siphoning spills. Model SPFP30 Food Processing 4

8 Recommended Installation Guide Available Accessories: 1. Surge Suppressor 2. Filter/Regulator 3. Air Dryer Unregulated Air Supply to Surge Suppressor 1 Surge Suppressor Pressure Gauge Shut-Off Valve Note: Surge Suppressor and Piping must be supported after the flexible connection. Pipe Connection (Style Optional) Flexible Connector Discharge Check Valve 2: INSTAL & OP Muffler (Optional Piped Exhaust) Flexible Connector Vacuum Gauge Drain Port Flexible Connector 3 2 Shut-Off Valve Air Inlet Filter Regulator P/N: 020.V Suction Air Dryer Shut-Off Valve Drain Port Pipe Connection (Style Optional) Note: Pipe weight should not be supported by pump connections. CAUTION The air exhaust should be piped to an area for safe disposition of the product being pumped, in the event of a diaphragm failure. Installation And Start-Up Locate the pump as close to the product being pumped as possible. Keep the suction line length and number of fittings to a minimum. Do not reduce the suction line diameter. Air Supply Connect the pump air inlet to an air supply with sufficient capacity and pressure to achieve desired performance. A pressure regulating valve should be installed to insure air supply pressure does not exceed recommended limits. Air Valve Lubrication The air distribution system is designed to operate WITHOUT lubrication. This is the standard mode of operation. If lubrication is desired, install an air line lubricator set to deliver one drop of SAE 10 non-detergent oil for every 20 SCFM (9.4 liters/sec.) of air the pump consumes. Consult the Performance Curve to determine air consumption. Air Line Moisture Water in the compressed air supply may cause icing or freezing of the exhaust air, causing the pump to cycle erratically or stop operating. Water in the air supply can be reduced by using a point-of-use air dryer. Air Inlet And Priming To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air flow as desired. If opening the valve increases cycling rate, but does not increase the rate of flow, cavitation has occurred. The valve should be closed slightly to obtain the most efficient air flow to pump flow ratio. 5 Model SPFP30 Food Processing

9 Troubleshooting Guide Symptom: Potential Cause(s): Recommendation(s): Pump Cycles Once Pump Will Not Operate / Cycle Pump Cycles and Will Not Prime or No Flow Pump Cycles Running Sluggish/Stalling, Flow Unsatisfactory Product Leaking Through Exhaust Premature Diaphragm Failure Deadhead (system pressure meets or exceeds air supply pressure). Air valve or intermediate gaskets installed incorrectly. Bent or missing actuator plunger. Pump is over lubricated. Lack of air (line size, PSI, CFM). Check air distribution system. Discharge line is blocked or clogged manifolds. Deadhead (system pressure meets or exceeds air supply pressure). Blocked air exhaust muffler. Pumped fluid in air exhaust muffler. Pump chamber is blocked. Cavitation on suction side. Check valve obstructed. Valve ball(s) not seating properly or sticking. Valve ball(s) missing (pushed into chamber or manifold). Valve ball(s)/seat(s) damaged or attacked by product. Check valve and/or seat is worn or needs adjusting. Suction line is blocked. Excessive suction lift. Suction side air leakage or air in product. Pumped fluid in air exhaust muffler. Over lubrication. Icing. Clogged manifolds. Deadhead (system pressure meets or exceeds air supply pressure). Cavitation on suction side. Lack of air (line size, PSI, CFM). Excessive suction lift. Air supply pressure or volume exceeds system hd. Undersized suction line. Restrictive or undersized air line. Suction side air leakage or air in product. Suction line is blocked. Pumped fluid in air exhaust muffler. Check valve obstructed. Check valve and/or seat is worn or needs adjusting. Entrained air or vapor lock in chamber(s). Diaphragm failure, or diaphragm plates loose. Diaphragm stretched around center hole or bolt holes. Cavitation. Excessive flooded suction pressure. Misapplication (chemical/physical incompatibility). Incorrect diaphragm plates or plates on backwards, installed incorrectly or worn. Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow. (Does not apply to high pressure 2:1 units). Install gaskets with holes properly aligned. Remove pilot valve and inspect actuator plungers. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation. Check the air line size and length, compressor capacity (HP vs. cfm required). Disassemble and inspect main air distribution valve, pilot valve and pilot valve actuators. Check for inadvertently closed discharge line valves. Clean discharge manifolds/piping. Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow. (Does not apply to high pressure 2:1 units). Remove muffler screen, clean or de-ice, and re-install. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly. Disassemble and inspect wetted chambers. Remove or flush any obstructions. Check suction condition (move pump closer to product). Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket. Clean out around valve ball cage and valve seat area. Replace valve ball or valve seat if damaged. Use heavier valve ball material. Worn valve ball or valve seat. Worn fingers in valve ball cage (replace part). Check Chemical Resistance Guide for compatibility. Check Chemical Resistance Guide for compatibility. Inspect check valves and seats for wear and proper setting. Replace if necessary. Remove or flush obstruction. Check and clear all suction screens or strainers. For lifts exceeding 20 of liquid, filling the chambers with liquid will prime the pump in most cases. Visually inspect all suction-side gaskets and pipe connections. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly. Set lubricator on lowest possible setting or remove. Units are designed for lube free operation. Remove muffler screen, de-ice, and re-install. Install a point of use air drier. Clean manifolds to allow proper air flow Increase the inlet air pressure to the pump. Pump is designed for 1:1 pressure ratio at zero flow. (Does not apply to high pressure 2:1 units). Check suction (move pump closer to product). Check the air line size, length, compressor capacity. For lifts exceeding 20 of liquid, filling the chambers with liquid will prime the pump in most cases. Decrease inlet air (press. and vol.) to the pump. Pump is cavitating the fluid by fast cycling. Meet or exceed pump connections. Install a larger air line and connection. Visually inspect all suction-side gaskets and pipe connections. Remove or flush obstruction. Check and clear all suction screens or strainers. Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket. Inspect check valves and seats for wear and proper setting. Replace if necessary. Purge chambers through tapped chamber vent plugs. Purging the chambers of air can be dangerous. Replace diaphragms, check for damage and ensure diaphragm plates are tight. Check for excessive inlet pressure or air pressure. Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitations and lubrication. Enlarge pipe diameter on suction side of pump. Move pump closer to product. Raise pump/place pump on top of tank to reduce inlet pressure. Install Back pressure device (Tech bulletin 41r). Add accumulation tank or pulsation dampener. Consult Chemical Resistance Chart for compatibility with products, cleaners, temperature limitations and lubrication. Check Operating Manual to check for correct part and installation. Ensure outer plates have not been worn to a sharp edge. Unbalanced Cycling Excessive suction lift. For lifts exceeding 20 of liquid, filling the chambers with liquid will prime the pump in most cases. Undersized suction line. Meet or exceed pump connections. Pumped fluid in air exhaust muffler. Suction side air leakage or air in product. Check valve obstructed. Check valve and/or seat is worn or needs adjusting. Entrained air or vapor lock in chamber(s). Disassemble pump chambers. Inspect for diaphragm rupture or loose diaphragm plate assembly. Visually inspect all suction-side gaskets and pipe connections. Disassemble the wet end of the pump and manually dislodge obstruction in the check valve pocket. Inspect check valves and seats for wear and proper setting. Replace if necessary. Purge chambers through tapped chamber vent plugs. 2: INSTAL & OP Model SPFP30 Food Processing 6

10 Composite Repair Parts Drawing - FDA Santoprene Fitted Torque to: 60 in-lbs Torque to: 275 in-lbs : EXP VIEW Torque to: 300 in-lbs WARREN RUPP INC. THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC. DESCRIPTION E3 FP RUBBER FITTED PUMP REV REVISION CHG DATE APP DATE ECN DRAWING NUMBER E3SJxxxx0C-ATEX REV 01 7 Model SPFP30 Food Processing

11 Composite Repair Parts List - FDA Santoprene Fitted Air Valve Assembly Item # Qty. Description Part Number Nickle Plated 1 1 Valve Body (includes items 2-11) Valve Body Valve Body Gasket Valve Sleeve O-ring Valve Spool Assembly (Includes items 7) Glyde Ring Assembly Stainless Steel Air Valve Screen End Cap Gasket End Cap Mounting Screws Center Section Assembly Item # Qty. Description Part Number Nickle Plated Stainless Steel 12 1 Center Block Assembly (Includes item 13) Main Shaft O-Ring Air Chamber Air Chamber Gasket Bolt Pilot Sleeve Assembly (include item 18) O-ring Retaining Ring Pilot Spool Assembly (Includes item 21) O-ring Muffler Diaphragm Assembly / Elastomers Part Number Item # Qty. Description SPFP30NPS SPFP30SSS FDA Santoprene FDA Santoprene 23 1 Main Shaft Diaphragm Outer Diaphragm Plate Inner Diaphragm Plate Bolt Washer Bumper Washer Back-Up Washer Valve Seat Valve Ball Wet End Assembly Item # Qty. Description Part Number 33 2 Water Chamber Large Clamp Half 35 4 Bolt 36 4 Large Wing Nut 37 1 Discharge Manifold 38 1 Suction Manifold 39 8 Small Clamp Half 8 Bolt 41 8 Small Wing Nut : EXP VIEW Model SPFP30 Food Processing 8

12 Composite Repair Parts Drawing - PTFE Fitted Torque to: 480 in-lbs Torque to: 480 in-lbs Torque to: 60 in-lbs 7 9 BONDED DIAPHRAGM ASSEMBLEY BONDED DIAPHRAGM ASSEMBLEY Torque to: 480 in-lbs : EXP VIEW Torque to: 275 in-lbs WARREN RUPP INC. THIS IS A PROPRIETARY DOCUMENT. DO NOT REPRODUCE OR DISCLOSE WITHOUT THE EXPRESS WRITTEN PERMISSION OF WARREN RUPP INC. DESCRIPTION E3 FP PTFE FITTED PUMP REV REVISION CHG DATE APP DATE ECN DRAWING NUMBER E3Sx5xxx0C-FP-ATEX REV 01 9 Model SPFP30 Food Processing

13 Composite Repair Parts List - PTFE Fitted Air Valve Assembly Item # Qty. Description Part Number Nickle Plated 1 1 Valve Body (Includes items 2-11) Valve Body Valve Body Gasket Valve Sleeve O-ring Valve Spool Assembly (Includes items 7) Glyde Ring Assembly Notes: In addition to this seat, (4) O-Rings are needed. Stainless Steel Air Valve Screen End Cap Gasket End Cap Mounting Screws Center Section Assembly Item # Qty. Description Part Number Nickle Plated Stainless Steel 12 1 Center Block Assembly (Includes item 13) Main Shaft O-Ring Air Chamber Air Chamber Gasket Bolt Pilot Sleeve Assembly (Include item 18) O-ring Retaining Ring Pilot Spool Assembly (Includes item 21) O-ring Muffler Diaphragm Assembly / Elastomers Item # Qty. Description 23 1 Main Shaft 24 2 Diaphragm 25 1 Back Up Diaphragm 26 2 Outer Diaphragm Plate 27 2 Inner Diaphragm Plate 28 2 Bumper Washer 29 2 Back-Up Washer 30 4 Valve Seat 31 4 Valve Ball Part Number Nickle Plated Air End PTFE Two Piece (See Note 1) Wet End Assembly Item # Qty. Description Part Number 32 2 Water Chamber Large Clamp Half Bolt Large Wing Nut Discharge Manifold Suction Manifold Small Clamp Half Bolt Small Wing Nut Diaphragm Seal Tape Kit (Not pictured) : EXP VIEW Model SPFP30 Food Processing 10

14 DECLARATION OF CONFORMITY DECLARATION DE CONFORMITE DECLARACION DE CONFORMIDAD ERKLÄRUNG BEZÜGLICH EINHALTUNG DER VORSCHRIFTEN DICHIARAZIONE DI CONFORMITÀ CONFORMITEITSVERKLARING DEKLARATION OM ÖVERENSSTÄMMELSE EF-OVERENSSTEMMELSESERKLÆRING VAATIMUSTENMUKAISUUSVAKUUTUS SAMSVARSERKLÄRING DECLARAÇAO DE CONFORMIDADE MANUFACTURED BY: FABRIQUE PAR: FABRICADA POR: HERGESTELLT VON: FABBRICATO DA: VERVAARDIGD DOOR: TILLVERKAD AV: FABRIKANT: VALMISTAJA: PRODUSENT: FABRICANTE: STANDARD PUMP, INC Satellite Blvd., Suite D Duluth, GA USA Tel: PUMP MODEL SERIES: SPFP05, SPFP10, SPFP15, SPFP20, SPFP30, SPSN15, SPSN20, SP3A15, SP3A20 This product complies with the following European Community Directives: 2006/42/EC Ce produit est conforme aux directives de la Communauté européenne suivantes: Este producto cumple con las siguientes Directrices de la Comunidad Europea: on Machinery, according Dieses produkt erfüllt die folgenden Vorschriften der Europäischen Gemeinschaft: to Annex VIII Questo prodotto è conforme alle seguenti direttive CEE: Dir produkt voldoet aan de volgende EG-richtlijnen: Denna produkt överensstämmer med följande EU direktiv: Standard Pump, Inc., erklærer herved som fabrikant, at ovennævnte produkt er i overensstemmelse med bestemmelserne i Direkktive: Tämä tuote täyttää seuraavien EC Direktiivien vaatimukstet: Dette produkt oppfyller kravene til følgende EC Direktiver: Este produto está de acordo com as seguintes Directivas comunitárias: This product has used the following harmonized standards to verify conformance: Ce materiel est fabriqué selon les normes harmonisées suivantes, afin d en garantir la conformité: Este producto cumple con las siquientes directrices de la comunidad europa: Dieses produkt ist nach folgenden harmonisierten standards gefertigtworden, die übereinstimmung wird bestätigt: Questo prodotto ha utilizzato i seguenti standards per verificare la conformita : De volgende geharmoniseerde normen werden gehanteerd om de conformiteit van dit produkt te garanderen: För denna produkt har följande harmoniserande standarder använts för att bekräfta överensstämmelse: Harmoniserede standarder, der er benyttet: Tässä tuotteessa on sovellettu seuraavia yhdenmukaistettuja standardeja: Dette produkt er produsert i overenstemmelse med fløgende harmoniserte standarder: Este produto utilizou os seguintes padrões harmonizados para varificar conformidade: EN809:1998+ A1:2009 AUTHORIZED / APPROVED BY: Approuve par: Aprobado por: Genehmigt von: approvato da: Goedgekeurd door: Underskrift: Valtuutettuna: Bemyndiget av: Autorizado Por: Chris Murphy Director of Operations DATE: July 20, 2012 FECHA: DATUM: DATA: DATO: PÄIVÄYS: 10/13/2015 REV 08 VMQR 044FM

15 DECLARATION OF CONFORMITY WITH ATEX 95 DIRECTIVE Date of Issue: 10 May 2014 Technical File No.: /MER Quality System Registration No: ISO Directive: Conforming Apparatus: Hazardous Location Applied: 94/9/EC 23 March 1994 Annex VIII Air-Operated Metal Double Diaphragm Pumps for Use In Potentially Explosive Atmospheres II 2 G c T5 II 2 D c T100 C T5 fluids up to 95 C Manufacturer: Standard Pump, Inc Satellite Blvd., Suite D Duluth, GA USA On File With: DEKRA Certification B.V. (0344) Meander MJ Arnhem The Netherlands Harmonized Standards Applied: BS EN :2009 Non-Electrical Equipment Potentially Explosive Atmospheres-Part 1 Basic Methods and Requirements EN :2011 Non-Electrical Equipment for Potentially Explosive Atmospheres-Part 5 Protection by Constructional Safety Equipment: SPFP20, SPFP30, SPSN20, SPFP15, SPSN15 We hereby certify that the above apparatuses described above conforms with the protection requirements of Council Directive 94/9/EC of 23 March 1994 Annex VIII on the approximation of the laws of the Member States Concerning Equipment and Protective Systems Intended for use in Potentially Explosive Atmospheres DATE/OF REVISION/TITLE: Chris Murphy 13 October 2015 Director of Operations

16 Declaration of Conformity Manufacturer: Standard Pump, Inc Satellite Blvd., Suite D, Duluth, GA 30097, USA certifies that Air-Operated Double Diaphragm Food Processing and Sanitary Pump Models comply with the European Community Regulation 1935/2004/EC for Food Contact Materials. Food Processing Pump Models: SPFP05PPS SPFP30NPS SPFP10PPS SPFP30SSS SPFP15NPS SPFP05PPP SPFP20NPS SPFP10PPP SPFP20SSS SPFP15NPP SPFP30NPT SPFP20NPP SPFP30SST SPFP20SSP Sanitary Pump Models: SPSN15NPS SPSN20NPS SPSN20SSS SPSN15NPP SPSN20NPP SPSN20SSP Signature of authorized person September 11, 2013 Date of issue Chris Murphy Printed name of authorized person Revision Level: B Director of Operations Title October 13, 2015 Date of revision