Safe Work Permits A Safety Advantage
|
|
- Oswald Harris
- 6 years ago
- Views:
Transcription
1 Safe Work Permits A Safety Advantage AMI Safety Conference March 20, 2013 J. Dan McCausland Senior Director, Worker Safety & HR
2 Safe Work Permits Everyone knows what a Hot Work Permit is -- right? Where do we use HWP s? Where don t we use HWP s? Why do we use? Provides extra focus on fire prevention. Do you use Work Permits at your facility? What permits do you require? Each type focuses on specific hazards outside normal work. Permits should be a key part of any plant safety program/process. Makes us stop and assess the hazards within an entire unit of work before exposures occur. Minimizes risk in non-standard situations.
3 Safe Work Permits Typically, we focus on production work. Also, on routine Sanitation and Maintenance work We know this work, and its hazards, well. Routinely prepare as needed for safety. Non-standard work are things outside our normal frame of reference. Often things done quarterly, or as part of other projects. Or, certain kinds of maintenance work. Ammonia system work Specialty sanitation (e.g. fumigation) Each type has intrinsic hazards that must be dealt with. Each type presents hazards that intrude on production work Permits for such work are task/hazard specific.
4 Today s Agenda: Safe Work Permits What is this about? What is the big picture with regard to Safety Permits? Why are permits necessary and/or appropriate? When are permits most useful? Where should permits be applied? How do you implement a Safety Permit process? Examples of permit applications
5 Safe Work Permits What is this all about? Most of our work is standard and repetitive in nature. Has a variety of risks, but usually those are well known and with safe job practices in place. We are de-sensitized work is normal in a normal area. Non-standard work also occurs from time to time. Need to prepare for those occasions, because they are out of the ordinary frame of reference for standard work. Such work may pose particularly serious hazards and require more than normal attention. These situations are perfect applications for the use of taskspecific safety permits.
6 Safe Work Permits Why bother? One word, Safety. Makes us evaluate the work that will be performed in our otherwise normal work area for possible hazards. Makes us define what Safe Work practices are, and how to follow same for this case. When Every time non-standard work will be done Permit(s) should at least be considered up front. Where Throughout the facility, and grounds.
7 Safe Work Permits How do we set up a Safe Work Permit Process? Identify each type of non-standard work. Key is to do this up front, with time to plan. Evaluate risk/hazard potential. Involve local SME s (subject matter experts). Use the What If analysis approach. Define the safe work process (to be followed). Develop in sufficient detail. Practice the doctrine of no surprises. Define who will be involved, who needs to approve, etc. Plan work well in advance. Cross check for complications of other work being done at same place and time. Resolve any territorial issues.
8 Safe Work Permits How do we set up a Safe Work Permit Process (continued)? Notify all who may be in the work area doing other tasks; may have to clear the work area. Work site security is essential. No non-essential personnel in area during permit work. Follow through with work according to permit plan. Close the permit: follow-up session to learn for next occurrence. Maintain a file on each class of permits will ultimately be very helpful for repeated occurrences of such work.
9 Safe Work Permits What kind of work may warrant a Safe Work Permit? Ammonia system line breaking/opening, device work, etc. Confined Space Entry as required for permit spaces. Energized (live) Electrical Work all occasions Natural Gas work venting, blowing, purging, etc. Hot work outside the welding shop, etc. Sprinkler system impairments, maintenance Extraordinary Hazardous Chemical work Trenching Crane/derrick rigging and lifting Critical Safety Bypass/Device Override situations Let s consider potential permits for each of these work types.
10 Ammonia Line Breaking Permit Valves, Relief valves, Flanges, Piping, Insulation, etc. Pre-work Safety review/plan Subject matter experts involved in review/plan of work. Procedures for opening a pressurized system Lines pumped down and confirmed empty Pipes plugged or capped as appropriate PPE including SCBA, eye wash/shower in place LO/TO for all related valves, vessels Nearest shut-off valves pre-identified Other permits needed Hot work, etc. Return to service protocol to assure safe restart Leak tests completed Formal sign-off on completion of work, permit.
11 Confined Space Entry Permit Follow OSHA 29CFR these things can be deadly; no 2 nd Chance to get it right. Plan the work Characterize the space as Permit or non-permit Plan the entry based on the hazard(s) present Atmospheric checks initial, ongoing Isolation, ventilation Lockout as appropriate to condition PPE body harness, tripod, SCBA, etc. Communication and Rescue procedures planned Permit closing review
12 Energized Electrical Work Permit Require justification why do we have to work hot? Assess Hazard(s) devices, max. voltage/current, etc. Plan the work Job brief by (at least 2) qualified employees Establish Arc Flash boundaries PPE Helmet, V-rated gloves, FRC, etc. Clear the area Complete work under direct supervision Return to service protocol to assure safe restart System returned to Safe status Exposed electrical devices/wiring closed. Formal sign-off on completion of work, permit.
13 Natural Gas Line/Use Permit Incidents where NG permits were not used. Slim Jim plant (NC) explosion and fire Kleen Energy utility plant (CT) explosion Gas-fired hot water heater installation Plan the work and permit conditions Purging, Blowing, or Venting applications Line breaking or new equipment installation Secure ignition sources; clear area Lockout valves Ventilate Return to service protocol to assure safe restart Formal check for leaks Sign-off on completion of work, permit.
14 Hot Work Permit Welding, cutting, plasma arc all types of hot work Use FM Global HWP process very comprehensive Plan the work Precautions specific to area flammables, gases, liquids, etc. Explosive atmospheres must be neutralized Pressurized vessels must be purged, vented and neutralized Pre-work cleanup (e.g. dust) and LO/TO as appropriate. Sprinklers, extinguishers in place and working Protect materials on other side of walls, ceilings, etc. Fire watch during and 1-2 hours after work Return to service protocol to assure safe restart Formal check-off 4 hours post work Sign-off on completion of work, permit.
15 Sprinkler System impairment Permit Whenever a FP water supply valve is closed or water shut-off to the system; sprinklers are out of service. Notify property insurer, fire department, etc. Post fire watch during maintenance work. Provide extra fire safety support. No Hot Work allowed during impairment. Restore system to service and check pressure at inspectors test valve to assure safe restart. Formal check for leaks, other issues. All valves verified as open (in fire water supply loop). Sign-off on completion of work, permit.
16 Hazardous Chemical Permits Use for non-routine chemical applications where chemicals present toxic/deadly properties. Specialty cleanup work, Pesticide/fumigate applications, etc. Plan the work Pre-work meeting; who s required, timeframe, preparations, etc. Review nature of chemicals to be used, OSHA safety data sheets; application criteria and hazard analysis. PPE as appropriate to hazards Secure the area to be treated; no non-essential employees. Perform work. Return to service protocol to assure safe restart Formal check for residual chemical properties Sign-off on completion of work, permit.
17 Other Potential Permits Trenching Treat as a Permit-required Confined Space Follow OSHA rules on shoring, use trench boxes, etc. Monitor from outside trench. Critical Safety Device Override Similar to hot electrical work Lockout to extent possible Active monitoring in place while bypass is in effect. Cranes and Derricks Lifting Permits Clear the area below the lift; maintain security. Review crane and rigging documentation, certificates, etc. Follow OSHA rules rigging, supervision, load control, etc.
18 Conclusion What is unique to each of these work situations? They are outside the normal conduct of production work. Not on our typical radar screen. Hazards associated with each are deadly; injury potential is severe. Bad planning (or no planning) can result in fatalities. Permit processes create safe work conditions, and that is essential.
19 Conclusion Questions and discussion Sample permits are available for those who would like a copy. We will be happy to discuss later as well, and appreciate your time today.
20 Thank you!
TABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
More informationLOCKOUT/TAGOUT PROGRAM
LOCKOUT/TAGOUT PROGRAM HOW CLIMATE ENGINEERS INC. COMPLIES WITH THELO/TO STANDARD It is the intent of Climate Engineers Inc. to comply with OSHA s Control of Hazardous Energy Standard (1910.147). The following
More informationProcess Safety Management Of Highly Hazardous Chemicals OSHA 29 CFR
Process Safety Management Of Highly Hazardous Chemicals OSHA 29 CFR 1910.119 PSM - Definition Not all refining hazards are caused by the same factors or involve ve the same degree of potential damage.
More informationSafety Manual Section 6 Confined Space
6. CONFINED SPACE ENTRY Introduction The following sections provide general guidelines and procedures for confined space entry. This section covers the following topics: Topic Page 6.1 Types of s... 6-2
More informationLOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.147 BASIS: Approximately three million workers in the United States face risks from uncontrolled energy when servicing machinery
More informationSPECIALIZED ONLINE TRAINING COURSE LIST
SPECIALIZED ONLINE TRAINING COURSE LIST Grainger Online Safety Manager provides you with access to online training courses covering today's most relevant safety topics. The training content is designed
More informationLO/TO LOCKOUT/TAGOUT PROGRAM
LO/TO LOCKOUT/TAGOUT PROGRAM April 2017 CONTENTS Section 1: Introduction...1 Section 2: Purpose... 1 Section 3: Application... 1 Section 4: Definitions... 2 Section 5: Roles and Responsibilities... 4 Section
More informationConfined Space. Program Responsibilities
Confined Space CONFINED SPACE ENTRY AND RESCUE The OSHA standard on Permit-Required Confined Spaces (29 CFR 1910.146) requires employers to implement practices and procedures to protect employees from
More informationOPERATING PROCEDURES
OPERATING PROCEDURES 1.0 Purpose This element identifies Petsec s Operating Procedures for its Safety and Environmental Management System (SEMS) Program; it applies to all Petsec operations. Petsec is
More informationCONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE
Office of Environmental Health & Safety CONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE LOCK OUT/TAG OUT OSHA 29 CFR 1910.147 rev. 3 2014 Director of Environmental Health & Safety Control of Hazardous Energy
More informationClear up confusion between the requirements for confined spaces and grain storage structures.
1 Clear up confusion between the requirements for confined spaces and grain storage structures. Discuss safe methods of entry. Keep employees safe during entry! 2 3 4 Work to identify ways to eliminate
More informationLockout/Tagout Program
Lockout/Tagout Program Control of Hazardous Energy Subpart J - 29 CFR 1910.147 29 CFR 1926.417 OSHA Standard All industries must comply Estimated to prevent Approximately 120 fatalities per year 28,000
More informationConfined Space Entry Safety Program
Confined Space Entry Safety Program Table of Contents SCOPE...2 DEFINITIONS..2 PROGRAM ELEMENTS...3 SPACE EVALUATION...4 IDENTIFICATION AND CLASSIFICATION...4 POSTING...4 RECLASSIFICATION OF PERMIT SPACE...4
More informationControl of Hazardous Energy Lockout / Tagout Program
Control of Hazardous Energy Lockout / Tagout Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 1 Environmental Health and Safety Personnel (EH&S)... 1 Directors
More informationHot Work Program. University of Wisconsin-Platteville Reviewed 4/2016
Hot Work Program University of Wisconsin-Platteville Reviewed 4/2016 The purpose of the Hot Work Program is to establish safety procedures for employees, contractors, and subcontractors engaging in any
More informationRecommended Facilitator Notes: (read the following text out-loud to participants while showing this slide)
Slide 1 Confined Space Entry for General Industry These materials have been developed based on applicable federal laws and regulations in place at the time the materials were created. The program is being
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationConfined Space Entry
Confined Space Entry Purpose The purpose of this document is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation,
More informationLockout / Tag out Program
Lockout / Tag out Program Presented by DOSHTI www.doshti.com You will learn Purpose of Lockout- Tag out Requirements for LOTO Types of Hazardous Energy Procedures for LOTO The OSHA Standard for the Control
More informationProduct Information Report Lockout/Tagout Hazardous Energy Control
Overview A properly implemented (LOTO) program is designed to protect workers involved in the maintenance and servicing of equipment from the dangerous effects of hazardous energy caused by the unexpected
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationWelding, Cutting, and Brazing
Welding, Cutting, and Brazing Hazards of Welding Operations Fire hazards Metal splatter Electric shock Explosion hazards Released gases Radiant energy Where would these hazards be found on oil and gas
More informationLockout/Tagout - Energy Control Program
Lockout/Tagout - Energy Control Program Lockout and Tagging of ELECTRICAL Circuits This portion of the K.R. Miller Contractors, Inc. safety program has been created to maintain a written copy of procedures
More information1.0 Scope and Application. 2.0 Definitions. Cal Poly Risk Management Confined Space Program Page 1
Page 1 1.0 Scope and Application The following procedures describe safe operating practices in confined spaces. These may be sewers, pipelines, tanks, boiler compartments, ducts, vaults, pits, vats, bins
More informationAPPLICIPABLE STANDARD: OSHA 29 CFR Confined Space Entry
Northeast Biomanufacturing Center and Collaborative Confined Space Entry (CSE) Program NBC-CSE-000 APPLICIPABLE STANDARD: OSHA 29 CFR 1910.146 Confined Space Entry Document Contents SECTION CONTENT A Scope
More informationPOTENTIAL HEALTH & SAFETY HAZARDS
Number: OH&S 18.09.1 Revision Date: 2011.06 Confined Space 1. PURPOSE 2. SCOPE 1.1. To properly designate Confined Spaces (CS) at Thompson Rivers University (TRU), to provide guidance to ensure the safety
More informationConfined Space Entry
Confined Space Entry Purpose The purpose of this chapter is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation,
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Replace a Light Ballast Job Title(s) Performing Task: Electrician, Maintenance
More informationEntrant / Attendant / Supervisor Training
Entrant / Attendant / Supervisor Training 1 This material was produced under Grant SH-21000-10-60-F-29 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily
More informationEH&S Program Occupational Safety Next Review: 5/9/19. Scope: University Wide Original date created: 2006
Environmental Health & Safety Policy and Procedure Subject: Confined Space Entry Policy & Procedure Published Date: 5/9/18 EH&S Program Occupational Safety Next Review: 5/9/19 Scope: University Wide Original
More informationBP OIL -- TOLEDO REFINERY
Document Type: Procedure BP OIL -- TOLEDO REFINERY Refinery Wide Reference No.: SAF 086 Effective Date: October 3, 2011 Use of Nitrogen (N 2 ) Rev. No.: 7 Owner: Jon Parker Auth. By: D. C. Durnwald (Signature
More informationHYDROSTATIC LEAK TEST PROCEDURE
This information is proprietary and shall not be disclosed outside your organization, nor shall it be duplicated, used or disclosed for purposes other than as permitted under the agreement with Kinetics
More informationMAGB HEALTH and SAFETY GROUP Working In Confined Spaces
MAGB HEALTH and SAFETY GROUP Working In Confined Spaces SCOPE: This document represents best practice advice available and considered pertinent after consultation within the membership and incorporating
More informationConfined Space Policy
Confined Space Policy Introduction Employees of Lawrence University may at times be required to enter into and perform work inside tanks, chests, sewers, vessels and other confined spaces. Due to the potentially
More informationCONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM March 2017 CONTENTS Section 1: Introduction... 1 Section 2: Purpose... 1 Section 3: Definitions... 2 Section 4: Roles and Responsibilities... 4 Section 5: Testing and Monitoring...
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
1. De-energize circuit serving the outlet following LOTO procedure (see pages 3 5). PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All
More informationSAFETY POLICY AND PROCEDURE MANUAL All Euramax Subsidiaries. Number K-3.0 Welding Safety Procedures
Number K-3.0 Issued: 1/2009 Revised: 3/2016 Page 1 of 3 1.0 PURPOSE: To standardize procedures associated with production and maintenance welding and to minimize the potential risk of accident or injury
More informationOrchard Farm Fire Protection District Standard Operating Procedure
Orchard Farm Fire Protection District Standard Operating Procedure Division: 200 Emergency Operations Section: 202 Fire & Rescue Subject: Supersedes: N/A Approved By: Page: 1 of 6 Date Last Reviewed: N/A
More informationSafe Work Practices (SWP) SWP (3) CONFINED SPACE ENTRY
SWP (3) CONFINED SPACE ENTRY The below information has been derived from BC WSBC OHS Regulations, standards and guidelines. If working outside of BC in a confined space, the work jurisdictions OHS Regulations/Codes
More informationConfined Space Entry Program Guidelines (Human Resources - Health and Safety Department)
Confined Space Entry Program Guidelines (Human Resources - Health and Safety Department) Introduction The Thames Valley District School Board, through the Health and Safety Policy is committed to providing
More informationDAILY EXCAVATION CHECKLIST
Appendix 2 Forms DAILY EXCAVATION CHECKLIST Client Project Name Project Location Job Number Excavation Size (Length x Width x Depth) Protective System Used Activities In Excavation Competent Person Date
More information29 CFR CONFINED SPACE ENTRY
29 CFR 1910.146 CONFINED SPACE ENTRY http://esf.uvm.edu/sirippt/powerpt.html 6/5/2000 Marvin Menesini What is a Confined Space? A space that: Is large enough and so configured that an employee can enter
More informationLockout - Tagout. Control of Hazardous Energy OSHA Standard
Lockout/Tagout Lockout - Tagout Control of Hazardous Energy OSHA Standard 1910.147 What Is Lockout/Tagout? Referred to as LOTO Blocks the flow of energy from power source to the equipment Provides means
More informationConfined Space Management
Confined Space Management Latest revised date: October 26, 2011 Page 1 of 8 1.0 Preamble Memorial has implemented workplace procedures to prevent unauthorized and unsafe confined space entry to guide the
More informationWelding and Cutting (Hot Work) Operations Self-Audit Checklist. Building Room Supervisor Date
Welding and Cutting (Hot Work) Operations Self-Audit Checklist Building Room Supervisor Date Audit Performed by A. General Welding and Cutting Controls 1. Welding and cutting operations restricted to authorized
More informationLockout/Tagout Training Overview. Safety Fest 2013
Lockout/Tagout Training Overview Safety Fest 2013 Purpose of Lockout/Tagout The standard covers the servicing and maintenance of machine and equipment in which the unexpected energization or start up of
More informationSECTION 51 NFPA 70E POLICY. Health & Safety Policy and Procedures Manual
SECTION 51 NFPA 70E POLICY Health & Safety Policy and 1. Protection Against Arc Flash A. Policy: An arc flash is a dangerous condition associated with the release of energy caused by an electric arc. An
More informationWHS CONTRACTOR INFORMATION PACKAGE
WHS CONTRACTOR INFORMATION PACKAGE Introduction This information package provides Informa exhibitors and contractors with important information that will be required to plan and manage work on all stages
More informationThe following were determined to be confined spaces; they may not be permit required that employees of the Division of Facilities may encounter:
Confined Space Classifications The following were determined to be confined spaces; they may not be permit required that employees of the Division of Facilities may encounter: Utility Tunnels, Crawl Spaces,
More informationElements of a Lockout/Tagout Program OSHA
September 15, 2015 Elements of a Lockout/Tagout Program OSHA 1910.147 Dayna Noble Industrial Safety Consultant Specialist Ohio BWC 567-204-8917 Dayna.noble@bwc.state.oh.us Top 10 most frequently cited
More informationElectrical Safety PPT-SM-ELECTSFTY V.A.0.0
Electrical Safety 1 Electrical Safety OSHA s electrical safety standard covers Work on or near exposed energized equipment Proper use of electrical protective equipment Safe use of portable electric equipment
More informationProcedure: Confined space safety
Purpose To define the requirements for the control of hazards associated with the use of confined spaces at the Australian National University to ensure compliance with the Work Health and Safety Act 2011
More information2018 NFPA 70E Electrical Safe work practices
This course provides a thorough knowledge of the dangers and recommended safe behaviors for those who work daily around electrical hazards. This course goes into examples of real life application to give
More informationLockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR
Volunteer State Community College Lockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR 1910.147 The information contained in this maual documents the policies and procedures
More informationOKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM. Environmental Health and Safety. Established:
OKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM Environmental Health and Safety Established: Developed in accordance with OSHA Standard 29 CFR 1910.147 1 1.0 SCOPE. Oklahoma City Community
More informationState University of New York College at Oneonta
State University of New York College at Oneonta CONFINED SPACE ENTRY POLICY - PROCEDURE REVIEWED 05/11/17 CONFINED SPACE ENTRY - WRITTEN PLAN POLICY The State University College at Oneonta is committed
More informationConfined Space Entry - General Industry & Construction. Leader s Guide and Quiz
4470 Confined Space Entry - General Industry & Construction Leader s Guide and Quiz INTRODUCTION TO THE PROGRAM Structure and Organization Information in this program is presented in a definite order,
More informationBASF Flash Fire FRC Assessment Tool
BASF Flash Fire FRC Assessment Tool Introduction The assessment tool offered in this document was developed to assist BASF manufacturing units in evaluating the potential for flash fire occurrence and
More informationELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
More informationHEAT EXCHANGE AND TRANSFER, INC. 500 Superior Street Carnegie, PA (412) Fax: (412)
SECTION Bypass Oil Sampling Station (B.O.S.S 1000) GENERAL.......................... SAFETY........................... Hazards............................... Personal Protective Equipment........... PRODUCT
More informationWorking in Confined & Enclosed Space Policy
Working in Confined & Enclosed Space Policy Author: Alan Bryant Page 1 of 9 Table of Contents: 1. INTRODUCTION... 3 2. DOCUMENT HISTORY... 3 3. REFERENCES... 3 4. PURPOSE... 4 5. SCOPE... 4 6. IMPLEMENTATION...
More informationThis session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its
This session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its standard on Control of Hazardous Energy. This is part
More informationLOCKOUT/TAGOUT PLAN August 2015
LOCKOUT/TAGOUT PLAN August 2015 Office of Environmental Health and Safety 423-354-5224 TABLE OF CONTENTS Purpose and Intended Use... 2 A. Types of Energy Sources... 2 B. Activities Requiring Lockout/Tagout
More informationAn Overview of Confined Space Rescue Course Objectives
An Overview of Confined Space Rescue 1 Course Objectives Provide the attendee with the basic understanding of the requirements of Confined Space Rescue so that the attendee can go to the next step of becoming
More informationCourse Objectives. An Overview of Confined Space Rescue
An Overview of Confined Space Rescue 1 Course Objectives Provide the attendee with the basic understanding of the requirements of Confined Space Rescue so that the attendee can go to the next step of becoming
More informationControl of Hazardous Energy (Lockout/Tag-out) 29 CFR
Control of Hazardous Energy (Lockout/Tag-out) 29 CFR 1910.147 What Is Lockout/Tag-out? Referred to as LOTO Blocks flow of energy from power source to the equipment Provides means of warning (tag) Regulatory
More informationBHG Operational Awareness Program May 8, 1998 Confined Spaces Revision 0 Page 1 of 13 CONFINED SPACES
Page 1 of 13 CONFINED SPACES 1.0 SCOPE This Performance Assessment Guide for Confined Spaces will be used to carry out the oversight responsibility of the U.S. Department of Energy (DOE) Brookhaven Group.
More informationDoc #: 1000-AD Revision: - CONFINED SPACES SOP. Author(s): T. Lavoie/ M. Saucedo/ J. Dunlop/ Mtn. Supervisor
Doc #: 1000-AD-015-0005 Revision: - CONFINED SPACES SOP Author(s): T. Lavoie/ M. Saucedo/ J. Dunlop/ Mtn. Supervisor TABLE OF CONTENTS REVISION HISTORY... 3 1.0 INTRODUCTION... 4 2.0 DEFINITIONS... 4 3.0
More informationWHS PROCEDURE P Confined Spaces. Approved by: Ruth Hampton Review Date: 6 th December 2015
5 WHS PROCEDURE P21-01 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment for all persons
More informationLOCATION OF WORK WRITTEN BY: APPROVED BY: DATE LAST REVISION Schools in PTSD Lorie Carriere Gordon Howe June 24, 2010 November 14, 2017
Page 1 of 8 LOCATION OF WORK WRITTEN BY: APPROVED BY: DATE LAST REVISION Schools in PTSD Lorie Carriere Gordon Howe June 24, 2010 November 14, 2017 HAZARDS PRESENT Sharp ceiling protrusions e.g. nails
More informationArc Flash. Safety 21
Arc Flash Safety 21 Arc Flash Introduction Electrical Hazards Safety Planning De-Energizing Equipment Working Hot Summary Introduction Most people don t think about electricity very much, which is surprising
More informationHAZARDOUS INCIDENT SITE SAFETY PLAN
HAZARDOUS INCIDENT SITE SAFETY PLAN NOTE: A site-specific Site Safety Plan must be developed and implemented for each site where investigators may potentially be exposed to hazardous substances while conducting
More information"CONFINED SPACE ENTRY"
PRESENTER'S GUIDE "CONFINED SPACE ENTRY" Training for THE OSHA PERMIT-REQUIRED CONFINED SPACES STANDARDS "Quality Safety and Health Products, for Today...and Tomorrow" OUTLINE OF MAJOR PROGRAM POINTS OUTLINE
More informationHazardous Energy Control/Lockout
This is a photographic template your photograph should fit precisely within this rectangle. Hazardous Energy Control/Lockout MESH 8.0 - Process Safety Awareness Training 2008 Eaton Corporation. All rights
More informationSafety Tips from the WorkSafe People. Building a Safety Program for Your Organization
Building a Safety Program for Your Organization 1 Content Criteria and Examples of Confined Spaces Permit-Required Confined Space Non-Permit-Required Confined Space Employer Requirements Employee Requirements
More informationU.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL
SAFE -14 Page 1 of 8 U.S. CONCRETE, INC. SAFETY POLICY and PROCEDURE MANUAL FUNCTION Safety TOPIC Hotwork Permit Program OBJECTIVE(S): GENERAL POLICY: To provide a work atmosphere that is conducive to
More informationUniversity of Arkansas Office of Environmental Health and Safety
University of Arkansas Office of Environmental Health and Safety Procedure Name: Lockout / Tagout Procedure Number: 600.26 Effective Date: 12-1-2015 Procedure: Developed in accordance with the OSHA Control
More informationConfined Space Program
Insert City Name Page 1 of 6 Purpose Regularly, confined spaces must be entered for inspection, cleaning or repair. Such spaces can present unusual hazards such as lack of sufficient oxygen, special mechanical
More informationRiskTopics. Lockout/Tagout October 2017
RiskTopics Lockout/Tagout October 2017 This Risktopic is designed to outline guidelines for lockout/tagout and provide assistance in developing a management program to reduce the risk of injury from unintended
More informationHAZARDOUS WASTE OPERATIONS AND EMERGENCY RESPONSE
Page 1 of 10 HAZARDOUS WASTE OPERATIONS AND EMERGENCY RESPONSE 1.0 SCOPE This Performance Assessment Guide for Hazardous Waste Operations and Emergency Response (HAZWOPER) will be used to carry out the
More informationSAFETY AND HEALTH STANDARD CONFINED SPACE ENTRY REQUIREMENTS Effective Date: 06/10/10 Standard: 16.2 Document Number: KUCSH0038 Rev: 07
16.2.1 INTRODUCTION 16.2.1.1 The purpose of this standard is to establish safety requirements, which include a permit system, for entry into confined spaces. 16.2.2 DEFINITIONS 16.6.2.1 Confined space
More informationConfined Space Procedure
APAC Confined Space Procedure S3[APAC]-301-PR1 1. Purpose and Scope a. The purpose of this procedure is to define safe systems of work for performing, managing or supervising confined space entry activities.
More informationLock Out/Tag Out Control of Hazardous Energy
Lock Out/Tag Out Control of Hazardous Energy University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF
More informationLockout Tagout Policy
Office of Environmental Health & Safety www.moreheadstate.edu/ehs 606-783-2584 Lockout Tagout Policy PURPOSE To establish procedures for the de-energization and isolation of energy sources or the lockout
More informationH. Control of Hazardous Energy: Lockout/Tag Out
H. Control of Hazardous Energy: Lockout/Tag Out 1. Purpose Control of Hazardous energy is the purpose of the Lockout- Tagout Program. This program establishes the requirements for isolation of both kinetic
More informationDoc No: WELDHOT Midland Engineering Co., Inc. Initial Issue Date 12/14/15 Safety Management System
Revision Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 7 PURPOSE To provide guidelines for the safe operation of welding, cutting and hot work of equipment, and to itemize
More informationControl of Hazardous Energy. Environmental Health and Safety
Control of Hazardous Energy Environmental Health and Safety 11/01/2014 1 CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) OSHA CFR 1910.147 Revised Date: November 2014 STATEMENT OF POLICY Ball State University
More informationManagement Plan for Electrical Safety ISD #535
Management Plan for Electrical Safety ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9 ½ Street Rochester, MN 55904 507-328-4507 MANAGEMENT PLAN FOR ELECTRICAL SAFETY Table of Contents
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationConfined Space Plan Environmental Health & Safety Office July 2017
Environmental Health & Safety Office July 2017 Table of Contents Table of Contents... i Acronyms... ii 1.0 Introduction... 1-1 1.1 Purpose... 1-1 1.2 Scope... 1-1 2.0 Roles and Responsibilities... 2-2
More informationConfined Space Entry Procedure
Purpose The purpose of this chapter is to establish methods to identify confined spaces, classify them according to their risks, and establish guidelines necessary for the safe preparation, entry and rescue
More informationConfined Space Entry
Confined Space Entry Construction Industry Standard 1926.21(b)(6) General Industry Standard 1910.146 Best Practices for all Industries Construction Industry Standard All employees required to enter into
More informationLockout / Tagout Program OSHA 29 CFR
Lockout / Tagout Program OSHA 29 CFR 1910.147 Baylor University utilizes outside contractors to perform set-up, maintenance, service, and repair to equipment utilized on campus. University staff perform
More informationPSM TRAINING COURSES. Courses can be conducted in multi-languages
Courses can be conducted in multi-languages One set of hardcopy course notes will be sent to client for printing and distribution to course participants. The courses will be held at the client s training
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT)
CONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) 1. PURPOSE The purpose of this program is to establish policy, rules and procedures for the protection of employees against the unexpected energizing, start-up,
More informationUTAS EH&S INSTRUCTION No. 036 June 2012 Revision No. 3. Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard)
Purging of Flammable Gas Equipment and/or Piping (Explosion Hazard) APPLICABILITY: This EH&S Instruction applies to UTAS sites worldwide, including contractors working at UTAS facilities. The document
More informationManagement Plan for Confined Spaces
IEA, INC. W A S ECA P U B L I C S C H O O L S I S D # 829 Contact Us: BROOKLYN PARK OFFICE 9201 W. BROADWAY, #600 BROOKLYN PARK, MN 55445 763-315-7900 MANKATO OFFICE 610 N. RIVERFRONT DRIVE MANKATO, MN
More information1.1 OHS Policy and Responsibilities
1.1 OHS Policy and Responsibilities At Canadian Rope Access Specialists Inc. safety is our primary concern and the health and safety of our employees, clients and contractors is of paramount importance
More informationSafety Training Topic HOT WORK
Safety Training Topic HOT WORK Purpose of Meeting To remind workers that perming hotwork can result in a serious injury. To reince hotwork safety rules. To consider ways to protect yourself from hotwork
More informationKey Technology, Inc. Confined Space Entry Program. July, 2017
Key Technology, Inc. Confined Space Entry Program July, 2017 Page 1 of 11 Key Technology, Inc. CONFINED SPACE ENTRY PROGRAM OVERVIEW Purpose: The purpose of this program is to ensure the protection of
More information