Vautex Elite ET Dual SCBA

Transcription

1 Operating Manual Vautex Elite ET Dual SCBA Chemical Protective Suit Type 1a EN 943-2:2002 Order No.: D /02

2 MSA AUER GmbH, D Berlin Thiemannstrasse 1 Germany MSA AUER GmbH. All rights reserved

3 MSA CONTENTS Contents 1. Safety Regulations Correct Use Liability Information Description Design of the Protective Suit Surfaces for Customer-Specific Marking Use Safety Instructions Helmet cover as visor holder Preparation Donning the Protective Suit Removing the Protective Suit Disposal Cleaning, Disinfection Cleaning Disinfection Maintenance Maintenance Intervals Tightness Test of the Protective Suit Replacing the Suit Valves Tightness Test of the Valves Zip Visual Control of the Protective Suit Repair Replacing the Lens Replacing the Gloves Replacing the Safety High Boots Transport and Storage Technical Data / Approvals Approvals General Characteristics of the Protective Suit Mechanical Characteristics of the Suit Material Chemical Characteristics of the Suit Material Ordering Information Vautex Elite ET Dual SCBA 3

4 SAFETY REGULATIONS MSA 1. Safety Regulations 1.1. Correct Use The chemical protective suit Vautex Elite ET Dual SCBA (hereinafter referred to as protective suit) is particularly intended to protect the wearer's skin from danger caused by liquid or gaseous toxic agents. As total encapsulating protective clothing it is worn over working clothes and the protective breathing apparatus. It offers excellent protection in emergencies, decontamination work, securing leaks or similar. The Vautex Elite ET Dual SCBA does not provide protection against heat or cold and is not itself a complete breathing protection apparatus. It must be worn in conjunction with the following series of compressed air breathing apparatus: Internal air supply with compressed air breathing apparatus (SCBA) models BD AirGo AirMAXX Classic DA 300 DA External air supply with ASV and SCBAs for decontamination purposes BD AirGo AirMAXX Classic DA 300 DA DSL air line 5, 10, 20 m up to a maximum length of 50 m. For decontamination purposes an external air supply can be connected. Information regarding the VFDB Directive 0802:2002 In the scope of the German fire brigades, the oxygen supply should not exceed 2000 l for the models mentioned above. The time the suit is worn should not exceed 30 minutes. [only available in German language] The protective suit described in this operating manual comply with the European Directives 89/686/EEC and 94/9/EC ( Section 7.1). The EC type examination was carried out by DEKRA EXAM GmbH (Dinnendahlstrasse 9, D Bochum).. Reference number of the organisation concerned: 0158 EC type certificate No A / 05 / 28 4 Vautex Elite ET Dual SCBA

5 MSA SAFETY REGULATIONS It is imperative that this operating manual be read and observed when using the protective suit. In particular, the safety instructions, as well as the information for the use and operation of the apparatus, must be carefully read and observed. Furthermore, the national regulations applicable in the user's country must be taken into account for a safe use. Danger! This product is supporting life and health. Inappropriate use, maintenance or servicing may affect the function of the device and thereby seriously compromise the user s life. Before use the product operability must be verified. The product must not be used, if the function test is unsuccessful, it is damaged, a competent servicing/maintenance has not been made, genuine MSA spare parts have not been used. Alternative use, or use outside these specifications will be considered as non-compliance. This also applies especially to unauthorised alterations to the apparatus and to commissioning work that has not been carried out by MSA or authorised persons Liability Information MSA accepts no liability in cases where the product has been used inappropriately or not as intended. The selection and use of the product are the exclusive responsibility of the individual operator. Product liability claims, warranties also as guarantees made by MSA with respect to the product are voided, if it is not used, serviced or maintained in accordance with the instructions in this manual. Vautex Elite ET Dual SCBA 5

6 DESCRIPTION MSA 2. Description 2.1. Design of the Protective Suit Fig. 1 Design of the Protective Suit 1 Suit shell 6 Gloves 2 Head strap (on the inside of the suit) 7 Rucksack 3 Helmet cover as visor holder 8 Safety high boot 4 Lens 9 External compressed air supply for decontamination purposes 5 Suit valves (2 pieces) The one-piece suit is made of a special compound material with a gas-tight zip protected by a zip cover. The zip runs vertically on the front from the right leg up to the head section. The lens is fitted gas and fluid-tight. The protective gloves and safety high boots can be changed and fitted as gas and liquid-tight. The helmet cover as visor holder provides added comfort to the protective suit. It fixes the visor of the protective helmet (only MSA GALLET Helmets F1S, F1SA, F1E and F1SF). 6 Vautex Elite ET Dual SCBA

7 MSA DESCRIPTION Wearing a protective suit and a compressed air breathing apparatus will put a physical strain on the wearer. Wearing the protective suit for extended periods can cause heat stress. The wearer must, therefore, be suited to wearing the protective suit (good health, possibly carry out a preventive medical examination first). Moreover, when in use, regional guidelines and accident prevention regulations must be observed. The operating time must be limited in accordance with specific national regulations. The back part is prepared for wearing a compressed air breathing apparatus under the protective suit. The head part in the protective suit is spacious enough to allow a protective helmet ( Section 3.1) to be worn under the protective suit. In order to adapt to different helmet sizes an adjustable head strap is fitted to the inside of the suit between both suit valves. The inhalation air is supplied to the wearer from the compressed air breathing apparatus via the automatic lung mechanisms and the full face mask. The exhalation air passes through the exhalation valve of the full face mask to the inside of the protective suit and finally via the suit valves into the ambient atmosphere. The suit is equipped with an additional external air supply connection which can be used for decontamination purposes in case of too low remaining breathing air capacity in the SCBA or an unlikely malfunction of the SCBA ( Section 2.2). The protective suit is equipped with transponder technology for protective suits. The transponder is an electronic data carrier on which a code is saved. The code is read contactless with the AUER transponder reader ( Section 8) and thus enables a clear identification of the chemical protective suit. In order to show, and to further process the code, a PC or MSA Proficheck and the corresponding MSA / TecBos software is required in conjunction with the AUER transponder reader. The service life of the protective suit is a minimum 15 years when correctly serviced and stored and does not apply to use. Operating temperatures: -30 C to +60 C Vautex Elite ET Dual SCBA 7

8 DESCRIPTION MSA 2.2. External compressed air supply for decontamination purposes Fig. 2 Air Line System Fig. 3 Automatic Switch Valve w/o whistle 1 Protective Suit 1 Connection to lung governed demand valve 2 Automatic Switch Valve (ASV) w/o whistle 3 External compressed air feeding 2 Connection to compressed air breathing apparatus 3 Automatic Switch Valve (ASV) w/o whistle 4 Compressed air feeding line The wearer of the suit is supplied with breathable air via a compressed air breathing apparatus worn on the back. This SCBA is mounted to the Automatic Switch Valve ( Fig. 2 and Fig. 3). The suit is equipped with an additional external air supply connection ( Fig. 3, Pos. 4) which can be used for decontamination purposes in case of too low remaining breathing air capacity in the SCBA or an unlikely malfunction of the SCBA. After connecting the external compressed air feeding ( Section 7) to the protective suit the ASV switches over automatically the breathable air supply from the SCBA to the external compressed air feeding. When the external air flow is interrupted, the pressure drops or the compressed air feeding is disconnected from the protective suit the ASV will switch back automatically to the SCBA.. 8 Vautex Elite ET Dual SCBA

9 MSA DESCRIPTION 2.3. Automatic Switch Valve (ASV) w/o whistle Please refer to the operation manual for the Automatic Switch Valve (ASV) w/o whistle when using this ASV Fig. 4 Automatic Switch Valve (ASV) w/o whistle 1 Connection, Mask Mounted Regulator (Lock coupling) 5 Clip 2 Locking Screw, Setback valve 6 Connection, Air supply hose (long plug nipple) 3 Connection, SCBA (short plug nipple) 7 Connection Tool Vautex Elite ET Dual SCBA 9

10 DESCRIPTION MSA 2.4. Surfaces for Customer-Specific Marking The following surfaces are provided on the protective suit for customer-specific marking. Front view Back view Fig. 5 Marking Surfaces on the Protective Suit Surfaces for Marking Field Max. sticker size 1 B 200 mm x H 400 mm 2 B 100 mm x H 700 mm 3 B 250 mm x H 700 mm 4 B 450 mm x H 550 mm 10 Vautex Elite ET Dual SCBA

11 MSA USE 3. Use 3.1. Safety Instructions In order to prevent electrostatic load when entering explosive atmospheres the protective suit must be moistened with water on the outside and kept moistened whilst in the explosive area. To comply with the ATEX classification ( Section 7.1) please apply antimist agent klar-pilot spray on the outside of the lens. The protective suit is not suitable for firefighting. Before donning the suit, the wearer must check that there are no missing parts (e.g. suit valves, gloves and boots). When using in the colder environments heat insulating clothing is recommended. As clothing under the protective suit the following is recommended: cotton underwear and socks, cotton gloves, e.g. one-piece overall with legs and sleeves that can be closed tightly or a firefighting protective suit, protective helmet (e.g. DIN firefighting helmet MSA Linesman, MSA GALLET: F1S, F1SA, F2 or F2 XTREM, protective helmets with helmet cover as visor holder (MSA GALLET F1S, F1SA, F1E, F1SF) ( Section 3.2) Helmet cover as visor holder The helmet cover as visor holder is available for the helmets MSA GALLET F1S, F1SA, F1E, F1SF. Pulling on the helmet cover as visor holder (1) Pull the helmet cover as visor holder over the visor. (2) Pull the helmet cover as visor holder completely over the bottom edge of the helmet. Vautex Elite ET Dual SCBA 11

12 USE MSA 3.3. Preparation Before donning the protective suit the following instructions must be followed: (1) Spread the protective suit on the floor. (2) Align the sleeves and legs of the protective suit ensuring there are no twists. (3) Open the zip fully and carefully in stages. (4) Treat the suit lens on the inside and the lens of the respiratory protective mask on the inside and outside with the anti-misting agent MSA klar-pilot. (5) Place the safety high boots upright and expose the boot openings. (6) Align the suspenders if available. (7) Switch on the radio, adjust and test. (8) Check the compressed air breathing apparatus and full face mask in accordance with the corresponding operating manual and check the sealing Donning the Protective Suit When donning the protective suit a second person (assistant) is required to help. Suspenders can be supplied by MSA as an option including a supplementary sheet for donning. They keep the suit held in position better. The suspenders do not form part of the supply of the EC prototype test! Donning respiratory protection (1) Put the compressed air breathing apparatus and full face mask on. (2) Open cylinder valves fully. (3) Don the protective helmet and put on the cotton gloves. Ensure that the mask is properly tightened since it could slip as a result of the wearer's increased sweat when wearing the protective suit. Adjusting the head strap (4) The assistant adjusts the head strap so that the head section is set to the optimum size for the size of the helmet. Donning the boots (5) Stand next to the protective suit, remove footwear. (6) Step into the suit. (7) Step into the right, followed by the left, boot. 12 Vautex Elite ET Dual SCBA

13 MSA USE Attaching the support belt (8) Roughly adjust the length of the support belt from the crotch of the protective suit. (9) Pull the protective suit up to crotch. (10) Attach the support belt to the waist belt of the compressed air breathing apparatus. (11) Adjust the length of the support belt. The belt must be attached tightly whilst ensuring freedom of movement. Pulling the left glove over fully (12) The assistant holds on to the loose hanging sleeves of the protective suit at the support ring of the left glove system and pulls the sleeve without creases to the side. (13) Pull the left sleeve on fully whilst ensuring that the glove system fits properly. Pulling the protective suit on (14) The assistant raises the protective suit over the compressed air cylinders. (15) Hold the lens up by the bottom edge using your left hand. (16) The assistant places the head part over the helmet. Automatic Switch Valve (ASV) w/o whistle (17) Insert the clip of the ASV into the belt of the breathing apparatus. (18) Connect safety coupling of the SCBA to the short plug nipple. (19) Connect plug nipple of lung governed demand valve to the lock coupling. Fitting the radio (if available) (20) Connect the radio with the headset and place in the radio holder. (21) Carry out a communication test and adjust the channel and volume if required The radio pocket does not form part of the supply of the EC prototype test! Vautex Elite ET Dual SCBA 13

14 USE MSA Pulling the right glove over fully (22) The assistant holds on to the support ring of the right glove system and pulls the sleeve without creases to the side. (23) Pull the right sleeve on fully whilst ensuring that the glove system fits properly. Carefully close the zip by gently pulling. As the zip slider moves downwards, hold on to the suit material at the same level. Pulling with excessive force can lead to irreparable damage and to the zip opening when in use or losing its sealing. Make sure that both halves of the chain are located parallel to each other without lateral load. Closing the protective suit (24) Stretch your right arm gently backwards and downwards and use your left hand to hold the lens upwards by the bottom edge to ensure that the zip is freely accessible and tight for closing. (25) The assistant gently closes the zip in stages until reaching chest height. (26) The assistant connects the automatic lung mechanism. (27) The assistant gently fully closes the zip in stages. In order to prevent the penetration of toxic agents the zip must be fully closed. In order to verify this, the assistant must look through the lens from the outside to the zip end. If any light can be seen the zip must be closed up to the end chamber. (28) Close the push buttons on the zip cover. Check readiness for use (29) Check the freedom of movement of the head, arms and legs. (30) Test the radio (31) Indicate readiness for use. 14 Vautex Elite ET Dual SCBA

15 MSA USE 3.5. Removing the Protective Suit If the protective suit is heavily soiled a preliminary cleaning should be carried out by an assistant before removing to ensure that toxic agents are removed from the protective suit. Whilst doing so the protective suit remains fully donned and closed. The assistant must wear the appropriate personal protection equipment when doing this e.g. protective gloves, respiratory protection, protective suit. The preliminary cleaning is, if possible, performed using water with suitable detergent additives with the zip cover open. When removing the protective suit, avoid any contact with the soiled outside of the suit. To avoid any impurities from reaching the inside the assistant must ensure that he does not come into contact with them. In case of low remaining pressure in the SCBA, remove the protective cover from the pass through and connect external air supply (--> section 1.1) The removal of the protective suit is performed in reverse order from the donning procedure: Carefully open the zip by pulling gently. As the zip slider moves downwards, hold on to the suit material at the same level. Opening with excessive force can cause long-lasting damage. (1) Open the zip cover. (2) Pull your arms from the sleeves and hold on to the lens from the inside. (3) Open the protective suit carefully. (4) Disconnect the compressed air feeding line (inside the protective suit) from the ASV (see ASV manual). (5) Pull the protective suit off. (6) Disconnect all other air lines from the ASV. (7) Remove the ASV. (8) Remove the compressed air breathing apparatus. (9) In order to protect the inside of the suit from contamination fully close the zip of the removed protective suit (Disconnect the external compressed air feeding line from the protective suit.). (10) For transport of the protective suit, e.g. loosely fold the suit and pack into a polyethylene bag or similar Disposal The Protective clothing itself does not require any special handling with regard to disposal. However, the disposal of contaminated protective suits is carried out in accordance with local legislation depending on the extent of the contamination through toxic waste. Vautex Elite ET Dual SCBA 15

16 CLEANING, DISINFECTION MSA 4. Cleaning, Disinfection 4.1. Cleaning The protective suit must be cleaned after each use. To do this remove the valve discs of the suit ( Section 5.3) and unbutton the rucksack reinforcement. These parts must be cleaned separately and fitted back only after they have been dried. The use of cleaning and disinfection materials, or the use of cleaning and disinfection processes, which are not permitted by MSA, can damage the protective suit and can destroy its protective properties (e.g. the use of a washing machine and drier). Do not clean the protective suit using hard, sharp or pointed instruments. Do not use organic solvents for cleaning such as nitro thinner, alcohol, spirit, petrol. The protective suit is to be cleaned as follows: (1) If the protective suit is not too badly soiled wash it once by hand at 30 C using a mild detergent. If badly soiled repeat the washing procedure. (2) Then rinse twice in clear water. To ensure full tightness the zip links must be free from foreign bodies such as bristles, hairs, threads and other impurities. (3) Thoroughly clean the zip separately with water and a soft brush. (4) Then hang the protective suit by the boots to dry. The protective suit and the removed parts must not be dried in radiant heat (e.g. sunlight, radiators) to prevent destroying the structure of the protective suit. When using a drying cabinet, the temperature may not exceed 40 C. (5) After cleaning the protective suit disinfect it e.g. with the disinfectant AUER 90 ( Section 4.2). (6) Then rinse thoroughly with water! (7) After each use and cleaning/ disinfection, a tightness test of the protective suit and its valves is performed ( Section 5.2). (8) Grease the zip ( Section 5.5). (9) Replace the protective cover of the pass through Cleaning the Automatic Switch Valve w/o whistle Components of the breathing apparatus and the ASV that have been soiled should be thoroughly cleaned after usage, if required, with tepid water. To do this, seal the connection nipple, leave all pressure hoses attached and pressure-clean the ASV. Any remaining moisture should be dried at a maximum temperature of 40 C. The use of cleaning and disinfection materials, or the use of cleaning and disinfection processes, which are not permitted by MSA, can damage the ASV. Do not use organic solvents for cleaning such as nitro thinner, alcohol, spirit, petrol. 16 Vautex Elite ET Dual SCBA

17 MSA MAINTENANCE 4.3. Disinfection Disinfection should only be carried out as follows using disinfectant AUER 90 only: (1) Dilute the disinfectant AUER 90 with water (water temperature max. 30 C). (2) Immerse the parts to be disinfected directly in the disinfectant solution or apply the solution with a rag and allow it to work. (3) Then rinse all parts thoroughly with water. Concentration and working times of the disinfectant AUER 90: Concentration Working Time Normal disinfection 2.0% 15 Minutes The safety instructions on the bottle or container of the disinfectant AUER 90 must be observed. 5. Maintenance 5.1. Maintenance Intervals The maintenance work shall be carried out by qualified service engineers or technicians. The corresponding seminars can be ordered at MSA. All maintenance work carried out must be noted on the appropriate inspection plate. The maintenance periods specified below refer only to protective suits. Task to be Performed Before Use After Use 6-Monthly Every Two Years Cleaning, Disinfection X Maintenance X X Function test and tightness test X X Valve disc replacement X X Sealing ring replacement X Control by wearer X Service zip X X Vautex Elite ET Dual SCBA 17

18 MAINTENANCE MSA 5.2. Tightness Test of the Protective Suit After each use, after each cleaning / disinfection, after each maintenance / repair or on a halfyearly basis, a tightness test of the protective suit must be performed. In order to do so use the MSA suit tightness tester kit with the valve leak test adapter. The valves can be tested using a mask testing instrument in conjunction with the valve leak test adapter and the compensation container. The test instruments can be ordered separately at MSA ( Section 8). Only inflate the protective suit with clean oil-free compressed air (breathable air quality in accordance with EN 12021) to ensure that after the tightness test there are no residues left in the suit. In order to avoid erroneous measurement perform the test in a draught-free room. Test according to EN 464: (1) Remove the valve discs and angled prechambers, close the valve bodies with the valve closing cap (this can act simultaneously as a test and/or filling connection). (2) Inflate the suit to 18 mbar positive pressure. Whilst doing so the pressure must be held for 10 minutes at 17.0 ±0.5 mbar. (3) Reduce positive pressure to 16.5 ±0.3 mbar (test pressure). The maximum permitted pressure drop in 6 min: 3 mbar. (4) At the end of the test, reassemble the valve discs and the angled prechambers. (5) Then perform a valve tightness test ( Section 5.3). In practice the following maintenance test has divergently been tried and tested: (1) Remove the valve discs and angled prechambers, close the valve bodies with the valve closing cap (this can act simultaneously as a test and/or filling connection). (2) Inflate protective suit 18 ±0.5 mbar positive pressure. (3) Stabilising time approx. 3 min. (4) Reduce positive pressure to 16 ±0.5 mbar (test pressure). The maximum permitted pressure drop is in 3 min: 2 mbar. (5) At the end of the test reassemble the valve discs and angled prechambers. (6) Then perform a valve tightness test ( Section 5.3). In the event of doubt, check in accordance with EN 464 (see above). Checks in case of leaks If leaks are detected during the tightness test it must be checked whether the test instrument is tightly connected to the valve, the zip is fully closed and tight, the valves are properly assembled. 18 Vautex Elite ET Dual SCBA

19 MSA MAINTENANCE 5.3. Replacing the Suit Valves Fig. 6 Suit Valve 1 Ring nut 4 Valve housing 2 Slip ring 5 Valve disc 3 Gasket 6 Prechamber Removing the suit valves (1) Pull off the angled prechamber of the valve to be removed. (2) Open the suit and lay out the inside to allow access to the valve. (3) Use one hand to grip the valve housing from the outside and the other to unscrew the ring nut from the valve housing inwards using a valve spanner. Reassembling the suit valves (1) Insert the ring nut with the slip ring correctly fitted from inside through the head strap hole, the gasket opening and the valve hole on the suit shell. (2) Screw the valve housing onto the ring nut from the outside. (3) Use one hand to grip the valve housing from the outside and the other to screw on the ring nut from the inside to the valve housing using a valve spanner. The torque must be 250 Ncm. (4) Fit the valve disc. (5) Mount the prechamber by overstretching whereby the angled part is pointing in the direction of the boot Tightness Test of the Valves After each use and cleaning / disinfection and after each maintenance / repair task or every halfyear, a tightness test of the suit valves must be carried out. The tightness of the suit valves is to be checked using e.g. the MSA valve leak test adapter in connection with the compensation container and the mask tightness test instrument ( Section 5.1): create a negative pressure of 10 mbar. max. pressure change within one minute must not exceed 1 mbar. If a leak is detected, either the valve disc or the entire suit valve assembly must be replaced. To do this, the threaded ring is unscrewed from the inside of the suit using an assembly spanner. The valve discs and gaskets must be replaced every two years ( Section 5.1). Vautex Elite ET Dual SCBA 19

20 MAINTENANCE MSA 5.5. Zip 1 2 Fig. 7 Zip Area to be treated with Grease 1 Grease film 2 Zip links After each use, after each cleaning or disinfection or every half year ( Section 5.1) the zip should be lubricated using a grease pencil or it should be sprayed using a zip grease spray. This applies a thin film of grease to the zip links Visual Control of the Protective Suit The protective suit must be checked for irregularities. These include: scratches or abrasion points, breaks in the suit material swollen or brittle material and damaged seams. Visible changes to the outside of the suit material such as slight abrasion and / or slight discolouration do not impair its protective effectiveness against chemicals. The discharge of ageing inhibition agents during storage does not impair the quality of the safety high boots Maintenance of the Automatic Switch Valve w/o whistle Maintenance of the ASV according to the ASV manual Repair The repair of suit material, seams or the replacement of zips may only be carried out by MSA or MSA authorised customer service. Before submitting the protective suit for maintenance and/or repair purposes, it must be fully decontaminated, cleaned and disinfected. Confirmation of this is given on the maintenance and repair form ( Section 8). Only MSA original spare parts can be used for repairs Replacing the Lens The replacement of the lens is solely to be carried out by authorised workshops or by MSA customer service. 20 Vautex Elite ET Dual SCBA

21 MSA MAINTENANCE Replacing the Gloves Fig. 8 Gloves 1 Cuff tube (protective rubber) for outer glove 5 Rubber ring 2 Outer glove 6 Clamp protection 3 Inner glove 7 Screw and nut clamp 4 Tube piece Disassembling the outer gloves (1) Pull off cuff tube. (2) Pull off outer glove. Disassembling the inner gloves (1) Open zip fully. (2) Turn the sleeves of the protective suit inside out. (3) Loosen screw and nut clamp (SW7). (4) Pull out tube piece with glove. (5) Pull glove off tube piece. Vautex Elite ET Dual SCBA 21

22 MAINTENANCE MSA Reassembling the inner gloves In order to guarantee full tightness, check the tightness of the suit after each glove replacement before fitting the outer gloves ( Section 5.2). (1) Insert tube piece into glove cuff. (2) Insert tube piece and glove into the sleeve. (3) Align glove. (4) Fit the screw and nut clamp on. (5) Fit clamp protector under clamp. (6) Turn clamp lock on the screw clamp on the seam. (7) Tighten screw and nut clamp with SW7, tightening torque: 400 ±30 Ncm. (8) Push inner glove to the outside. Ensure that the clamp lock is on the seam and that the clamp protector covers the clamp lock. Reassembling the outer gloves (1) Takes place only after successful tightness test of protective suit. (2) Pull the outer glove over the inner glove. (3) The inner roll of the outer glove must be fitted into the groove of the tube piece. (4) Then assemble the cuff tube. 22 Vautex Elite ET Dual SCBA

23 MSA MAINTENANCE Replacing the Safety High Boots Fig. 9 Safety high boots 1 Safety high boot complete 5 Tube piece 2 Protective suit leg 6 Safety high boot 3 Screw and nut clamp 7 Cap tube (protective rubber) for safety high boot 4 Clamp protection Removing the safety high boots (1) Remove cap tube from the boot shaft. (2) Open protective suit zip fully. (3) Turn protective suit legs inside out. (4) Loosen and remove screw and nut clamp (SW7). (5) Pull out tube piece. (6) Remove safety high boot from the protective suit leg. Vautex Elite ET Dual SCBA 23

24 TRANSPORT AND STORAGE MSA Reassembling the safety high boots In order to guarantee full tightness, check the tightness of the suit ( Section 5.2) after each replacement of the safety high boots before the cap tube is fitted over the shaft of the boot. (1) Push safety high boot into the suit leg that was turned inside out. (2) Align suit leg and boot. (3) Insert tube piece in the boot shaft. (4) Fit the screw and nut clamp on. (5) Turn clamp lock towards the rear. (6) Fit clamp protector under clamp. (7) Tighten screw and nut clamp with SW7, tightening torque: 700 ±30 Ncm. (8) Clamp protection must cover the clamp lock. (9) Push safety high boot to the outside. (10) After tightness test, fit cap tube over shaft of boot. 6. Transport and Storage In order to prevent damage to the protective suit, the material, seams, and zip must not be forcibly kinked or folded! The zip should remain closed during storage. The suit can, for example, be loosely folded as a large package. The protective suit is supplied folded and pressure-free. Storage must be in a loosely folded pack in clean and dry conditions in a normal atmosphere free from toxic substances, protected from direct sunlight and temperature changes (according to DIN 7716 and ISO 2230). The operational life can change as a result of environmental influences, such as UV light, heat, humidity. The storage room must be cool, dry, dust-free and well ventilated. The storage temperature is between -5 C and +25 C. The optimum storage temperature is between +15 C and +25 C, since in the long-term there could otherwise be a change in the physical properties or a shortening of the service life. The relative air humidity is best at under 65%. When storing the protective suit on vehicles or containers abrasion through permanent friction with the contact surface has to be avoided. 24 Vautex Elite ET Dual SCBA

25 MSA TECHNICAL DATA / APPROVALS 7. Technical Data / Approvals 7.1. Approvals PPE Directive ATEX Directive Marine equipment directive 89/686/EEC EN 943-1:2002 EN 943-2: Type 1a (Internal compressed air breathing apparatus) Gas-tight (Type 1) chemical protective suits for emergency teams (ET) EN 14126: Type 1B Protective clothing for infective agents EN 533: Type 3 Limited flame spread EN :2002 Radioactive contamination by solid particles VfDB 0801: /9/EC EN :1997 EN :2002 If klar-pilot is used on the lens (outside) the following classifications are met: I M1 II 1G IIC T6-40 C Ta +60 C II 1D 96/98/EC SOLAS 74/88 Section II-2 Regulation , latest version 0158 EC type examination Surveillance acc. Article 11B DEKRA EXAM GmbH, Zertifizierungsstelle, Dinnendahlstr. 9, D Bochum DEKRA EXAM GmbH, Zertifizierungsstelle, Dinnendahlstr. 9, D Bochum Vautex Elite ET Dual SCBA 25

26 TECHNICAL DATA / APPROVALS MSA 7.2. General Characteristics of the Protective Suit Weight without the compressed air breathing apparatus and full approx. 8.5 kg face mask. Protective suit for heights between cm Size XL Protective suit for heights between cm Size L Protective suit for heights between cm Size M Gloves Size 11 Gloves Size 10 Gloves Size 9 Safety high boot Size 11½ (46/47) Safety high boot Size 10 (45) Safety high boot Size 9 (43/44) Operating temperature -30 C to +60 C Storage temperature -5 C to +25 C, optimal +15 C to +25 C 7.3. Mechanical Characteristics of the Suit Material Mechanical Characteristics Class Abrasion according to EN Blocking behaviour according to ISO Flexural crack resistance according to ISO Flexural crack resistance at low temperatures (-30 C) 2 according to ISO 7854 Flexural crack resistance at low temperatures (-60 C) 2 according to pren Further crack resistance (Trapezoid process) 5 according to ISO Bursting strength according to ISO Tensile strength to EN ISO Cutting resistance according to EN Resistance to ignition according to EN Seam resistance to EN ISO Vautex Elite ET Dual SCBA

27 MSA TECHNICAL DATA / APPROVALS 7.4. Chemical Characteristics of the Suit Material Resistance to permeation of chemicals. Test Chemical Suit Material Suit seams Inner Gloves Lens Boot Zip Pass- Thru Class Class Class Class Class Class Class Acetone Acetonitrile Ammonia (Gas) Chlorine (Gas) Hydrogen chloride (Gas) 1.2 Methylene * 6 chloride Diethylamin 6 5 1* Ethyl acetate * 6 n - Heptane Carbon disulphide Methanol Caustic soda 40% Sulphuric acid 96% Tetrahydrofuran 6 5 1* Toluol * 6 * Note: Not suitable for use with these chemicals under continuous exposure. Manufacturer recommendation: using in accordance with the scope of delivery with over glove results in class 2 of the glove components for both chemicals after tests. Without impairing the tightness with regard to the tested chemicals it can lead to material changes depending on the operating conditions. The evaluation of the retention behaviour is classified as follows in accordance with the European standard EN 369: Class Breakthrough Time 6 > 480 min 5 > 240 min 4 > 120 min 3 > 60 min 2 > 30 min 1 > 10 min Vautex Elite ET Dual SCBA 27

28 ORDERING INFORMATION MSA 8. Ordering Information Order Code for Protective Suit The order no. for the protective suit consists of A_Vautex Elite ET and an 8-digit code from A-H. A B C D E F G H Code Protective suit torso size Lens Safety high boots size Inner glove size Radio holder size Suspenders Marking Numbers size External air feed none none none none none none 1 M Standard UK 9 D 43/44 2 L UK 10 D 45 3 XL UK11 ½ D 46/ x35x95 equipped 100 mm Dual Airline 10 80x50x mm Dual SCBA 11 90x65x mm Dual LVS 600-D 4 90x40x mm The marking of the protective suit can be attached to the suit. A specific surface is to be provided for this, see Fig. 5 (not possible in connection with the trainer suit). MSA offers in its product portfolio a training version of the Vautex Elite ET. The material and the treatment of the seams of these training suits are not designed for protection against chemicals, but solely for training purposes. The fabric of the training suit is designed to resist abrasion and tearing also at frequent use in training galleries. Training suits are not part of the certification process. Please contact the MSA Customer Service for detailed information. Example for the Order No. of a Protective Suit: with torso size L (Code: 2) with standard lens (Code: 1) with safety high boot size D 45 (Code: 2) with inner glove size 9 (Code: 1) without radio holder (Code: 0) with suspenders (Code: 1) without marking on the protective suit (Code: 0) with external air connection (Code: 2) The above would result in the following article number: A B C D E F G H A_Vautex Elite ET The complete article number is: A_Vautex Elite ET Vautex Elite ET Dual SCBA

29 MSA ORDERING INFORMATION Article Numbers Protective Suit Parts and Accessories Description Gloves Part-No. Replacement gloves, inner size 11 D Replacement gloves, inner size Replacement gloves, inner size Replacement glove, outer, Multigrip size Replacement glove, outer, Multigrip size Replacement glove, outer, Tricotril size Replacement glove, outer, Tricotril size Replacement glove, outer, K-MEX N size Textile gloves (Packet with 5 pairs) D Cuff tube glove (unit) D Safety high boots Boot size 11½ (46/47) D Boot size 10 (45/) Boot size 9 (43/44) Cap tube boot (pair) D Spare Parts Suit valve for all CSA D O-ring for suit valve 40 x 30 x 1, 4 pcs D SCBA 360 Pass Thru Spare SCBA 360 Protective Cover (Packet of 5) Accessories Helmet as visor holder - MSA GALLET F1S, F1SA cover Helmet as visor holder - MSA GALLET F1E cover Helmet as visor holder - MSA GALLET F1SF cover GA1108A GA1108B GA1108C MP extension hose 0,5m [ASV] Maintenance and repair form D Grease pencil for zip D Syntheso W zip lubricant spray D AUER 90 disinfectant, 2l. D AUER 90 disinfectant, 6l. D Antimist agent klar-pilot spray Hanger for chemical protective suit D Transport case for chemical protective suit D Storage bag PE 2300 x 750 mm with slide lock D Valve spanner suit valves D Transponder reader Apparatus management software upon request upon request Vautex Elite ET Dual SCBA 29

30 ORDERING INFORMATION MSA Accessories Tightening Test, Testers Tightness tester kit for chemical protective suits D Valve lock cap D SP Valve lock cap D SP Mask tightness tester D Valve leak test adapter D Compensation container D Multitest Plus test case D Multitest Plus test console D CPS test line for Multitest D CPS valve test mechanism for Multitest D Computer-supported testers upon request 30 Vautex Elite ET Dual SCBA

31 MSA NOTES Vautex Elite ET Dual 31

32 MSA in Europe [ ] Northern Europe Southern Europe Eastern Europe Central Europe Netherlands MSA Nederland Kernweg LH Hoorn Phone +31 [229] Fax +31 [229] info.nl@msasafety.com France MSA GALLET Zone Industrielle Sud Châtillon sur Chalaronne Phone +33 [474] Fax +33 [474] info.fr@msasafety.com Poland MSA Safety Poland Sp. z o.o. Ul. Wschodnia 5A Raszyn k/warszawy Phone +48 [22] Fax +48 [22] info.pl@msasafety.com Germany MSA AUER GmbH Thiemannstrasse Berlin Phone +49 [30] Fax +49 [30] info.de@msasafety.com Belgium MSA Belgium N.V. Duwijckstraat Lier Phone +32 [3] Fax +32 [3] info.be@msasafety.com Great Britain MSA (Britain) Limited Lochard House Linnet Way Strathclyde Business Park BELLSHILL ML4 3RA Scotland Phone +44 [16 98] Fax +44 [16 98] info.gb@msasafety.com Sweden MSA NORDIC Kopparbergsgatan Malmö Phone +46 [40] Fax +46 [40] info.se@msasafety.com MSA SORDIN Rörläggarvägen Värnamo Phone +46 [370] Fax +46 [370] info.se@msasafety.com Italy MSA Italiana S.p.A. Via Po 13/ Rozzano [MI] Phone +39 [02] Fax +39 [02] info.it@msasafety.com Spain MSA Española, S.A.U. Narcís Monturiol, 7 Pol. Ind. del Sudoeste Sant-Just Desvern [Barcelona] Phone +34 [93] Fax +34 [93] info.es@msasafety.com Czech republic MSA Safety Czech s.r.o. Dolnojircanska 270/22b Praha 4 - Kamyk Phone Fax info.cz@msasafety.com Hungary MSA Safety Hungaria Francia út Budapest Phone +36 [1] Fax +36 [1] info.hu@msasafety.com Romania MSA Safety Romania S.R.L. Str. Virgil Madgearu, Nr. 5 Ap. 2, Sector Bucuresti Phone +40 [21] Fax +40 [21] info.ro@msasafety.com Russia MSA Safety Russia Походный проезд д Москва Phone +7 [495] Fax +7 [495] info.ru@msasafety.com Austria MSA AUER Austria Vertriebs GmbH Modecenterstrasse 22 MGC Office 4, Top Wien Phone +43 [0] 1 / Fax +43 [0] 1 / info.at@msasafety.com Switzerland MSA Schweiz Eichweg Oberglatt Phone +41 [43] Fax +41 [43] info.ch@msasafety.com European International Sales [Africa, Asia, Australia, Latin America, Middle East] MSA Europe Thiemannstrasse Berlin Phone +49 [30] Fax +49 [30] info.de@msasafety.com