View Section : Ingredient Name CAS# Ingredient Percent

Transcription

1 MSDS Name: KIT - 2-TON CLEAR EPOXY Manufacturer Name: ITW Devcon Manufacturer MSDS Revision Date: 09/06/2006 Product Codes: Components: : 2-TON CLEAR EPOXY HARDENER : 2-TON CLEAR EPOXY RESIN View Section : SECTION 1: CHEMICAL PRODUCT and COMPANY IDENTIFICATION Product Name: 2-TON CLEAR EPOXY HARDENER Manufacturer MSDS.: Manufacturer Name: ITW Devcon Address: 30 Endicott St. Danvers MA Business Phone: (978) Emergency Phone: (800) Revision Date: 09/06/2006 ACTIO MSDS ID: SECTION 2 : COMPOSITION, INFORMATION ON INGREDIENTS Ingredient Name CAS# Ingredient Percent Aminoethylpiperazine by Weight EC Index Number: 1 Nonylphenol by Weight EC Index Number: 1 SECTION 3 : HAZARDS IDENTIFICATION Emergency Overview: Corrosive. Toxic. Potential Sensitizer. Irritant. Applies to All Ingredients : Route of Exposure: Potential Health Effects: Skin Contact: Chronic Health Effects: Other Potential Health Effects: Aggravation of Pre-Existing Conditions: Skin contact Severe irritation or burns. May cause lacrimation, conjunctivitis, corneal damage and may cause permanent injury (ie. blindness). Severe irritation or burns, necrosis, blistering and permanent injury. Product can be absorbed through the skin and may cause nausea, headache and general discomfort. If the hardener is poorly ventilated, strongly heated or atomized, the vapor or mist can cause severe irritation of the respiratory tract, damage contacted tissue and produce scarring. Coughing and chest pain may result, nausea and vomiting in severe cases. Causes severe damage to mucous membranes if swallowed. May cause malaise, headache, discomfort bleeding and vomiting of blood. Prolonged or repeated overexposure by skin contact or inhalation may cause skin sensitization, with itching, swelling and rashes upon further exposure. Repeated or prolonged exposure may cause adverse eye effects (conjunctivitis, corneal damage), or skin effects (rash, irritation, corrosion). Nonyphenol has caused allergic sensitization in humans. None known. Asthma, eczema, or skin disorders and allergies, eye disease.

2 SECTION 4 : FIRST AID MEASURES Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Get immediate medical attention. Skin Contact: Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while removing contaminated clothing and shoes. Get medical attention if irritation develops or persists. If inhaled, remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical attention. If swallowed, do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. Other First Aid: Due to possible aspiration into the lungs, DO NOT induce vomiting if ingested. Provide a glass of water to dilute the material in the stomach. If vomiting occurs naturally, have the person lean forward to reduce the risk of aspiration. SECTION 5 : FIRE FIGHTING MEASURES Flash Point: Flash Point Method: Upper Flammable or Explosive Lower Flammable or Explosive Auto Ignition Temperature: Extinguishing Media: Unsuitable Media: Fire Fighting Instructions: Protective Equipment: Unusual Fire Hazards: F (101 C) Closed cup. Use carbon dioxide (CO2) or dry chemical when fighting fires involving this material. Water or foam may cause frothing. Evacuate area of unprotected personnel. Use cold water spray to cool fire exposed containers to minimize risk of rupture. Do not enter confined fire space without full protective gear. If possible, contain fire run-off water. As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear. Sealed containers at elevated temperatures may rupture explosively due to polymerization and/or pressure build up and spread fire. Sudden reaction and fire may result if product is mixed with an oxidizing agent. SECTION 6 : ACCIDENTAL RELEASE MEASURES Leak Response: Personal Precautions: Spill Cleanup Measures: Environmental Precautions: Large Spill: Corrosive. Avoid personal contact and breathing vapors or mists. Ventilate area. Use proper personal protective equipment as listed in section 8. Evacuate area and keep unnecessary and unprotected personnel from entering the spill area. Dike, contain, and soak up with an absorbent such as clay, sand, vermiculite, or other inert suitable material and dispose of properly. After removal, flush spill area with soap and water to remove trace residue. Avoid runoff into storm sewers, ditches, and waterways. Pump or shovel to storage/salvage vessels. SECTION 7 : HANDLING and STORAGE Handling: Storage: Hygiene Practices: Use with adequate ventilation. Avoid breathing vapor, aerosol or mist. Avoid contact with eyes and skin. Do not reuse containers without proper cleaning or reconditioning. Store in a cool, dry, well ventilated area away from sources of heat, combustible materials, and incompatible substances. Keep container tightly closed when not in use. Do not store in reactive metal containers. Keep away from acids, oxidizers. Wash thoroughly after handling. SECTION 8 : EXPOSURE CONTROLS, PERSONAL PROTECTION Engineering Controls: Use appropriate engineering control such as process enclosures, local exhaust ventilation, general dilution ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Where such systems are not effective wear suitable personal protective equipment, which performs satisfactorily and meets OSHA or other recognized standards. Consult with local procedures for selection, training, inspection and maintenance of the personal protective equipment. Skin Protection Description: Chemical-resistant gloves and chemical goggles, face-shield and synthetic apron or coveralls should be used to prevent contact with eyes, skin or clothing. Hand Protection Description: Wear appropriate protective gloves, neoprene, butyl rubber or nitrile. Consult glove manufacturer's data for permeability data. Eye/Face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR , OSHA eye and face protection regulation, or the European standard EN 166. Respiratory Protection: A NIOSH approved air-purifying respirator with an organic vapor/particulates combination cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known, or any other circumstances where air purifying respirators may not provide adequate protection. Other Protective: Facilities storing or utilizing this material should be equipped with an eyewash and a deluge shower safety station.

3 Ingredient Guidelines Ingredient: Aminoethylpiperazine OSHA PEL-STEL OSHA PEL-TWA ACGIH TLV-TWA ACGIH TLV-STEL Ingredient: Nonylphenol OSHA PEL-STEL OSHA PEL-TWA ACGIH TLV-TWA ACGIH TLV-STEL SECTION 9 : PHYSICAL and CHEMICAL PROPERTIES Color: Amber. Odor: Ammonia like fishy. Physical State: Liquid. ph: Alkaline. Vapor Pressure: <1 F Vapor Density: >1 (air = 1) Boiling Point: >392 F (200 C) Melting Point: Solubility in Water: Completely. Specific Gravity: 0.97 Evaporation Point: <1 (butyl acetate = 1) Percent Volatile: 0 Volatile Organic Compound 0 g/l Content: Molecular Formula: Molecular Weight: Percent Solids by Weight 100 SECTION 10 : STABILITY and REACTIVITY Chemical Stability: Conditions to Avoid: Incompatibilities with Other Materials: Hazardous Polymerization: Stable under normal conditions. Extreme heat or open flame. Product slowly corrodes copper, aluminum, zinc and galvanized surfaces. Oxidizers, acids, Clorinated organic cmpds. Reactive metals (e.g. Na, Ca, zinc). Sodium/calcium hypochlorite. Peroxides. Mat'ls reactive with hydroxyl cmpds. will not SECTION 11 : TOXICOLOGICAL INFORMATION Aminoethylpiperazine : Eye Effect: Skin Effects: Ingestion Effects: Inhalation Effects: Eye - rabbit Standard Draize test: 20 mg/24h - [Moderate](RTECS) Skin - rabbit Standard Draize test: 5 mg/24h - [Severe](RTECS) Skin - rabbit LD50: 880 ul/kg - [Details of toxic effects not reported other than lethal dose value](rtecs) Oral - rat LD50: 2140 ul/kg - [Details of toxic effects not reported other than lethal dose value] (RTECS) No data available SECTION 12 : ECOLOGICAL INFORMATION Ecotoxicity: Environmental Fate: No ecotoxicity data was found for the product. No environmental information found for this product. SECTION 13 : DISPOSAL CONSIDERATIONS Waste Disposal: Ignitable (Yes/No): Consult with the US EPA Guidelines listed in 40 CFR Part for the classifications of hazardous waste prior to disposal. Furthermore, consult with your state and local waste requirements or guidelines, if applicable, to ensure compliance. Arrange disposal in accordance to the EPA and/or state and local guidelines. No

4 SECTION 14 : TRANSPORT INFORMATION DOT Shipping Name: Corrosive liquid, basic, organic, n.o.s. DOT UN Number: 3267 DOT Hazard Class: 8 DOT Packing Group: III SECTION 15 : REGULATORY INFORMATION Aminoethylpiperazine : TSCA 8(b): Inventory Status: Canada DSL: Nonylphenol : TSCA 8(b): Inventory Status: Canada DSL: SECTION 16 : ADDITIONAL INFORMATION MSDS Revision Date: 09/06/2006 MSDS Author: Actio Corporation Disclaimer: This Health and Safety Information is correct to the best of our knowledge and belief at the date of its publication but we cannot accept liability for any loss, injury or damage which may result from its use. The information given in the Data Sheet is designed only as a guidance for safe handling, storage and the use of the substance. It is not a specification nor does it guarantee any specific properties. All chemicals should be handled only by competent personnel, within a controlled environment. Copyright Actio Corporation. All Rights Reserved. ACTIO MSDS ID: View Section : SECTION 1: CHEMICAL PRODUCT and COMPANY IDENTIFICATION Product Name: 2-TON CLEAR EPOXY RESIN Manufacturer MSDS.: Manufacturer Name: ITW Devcon Address: 30 Endicott St. Danvers MA Business Phone: (978) Emergency Phone: (800) Revision Date: 09/06/2006 SECTION 2 : COMPOSITION, INFORMATION ON INGREDIENTS Ingredient Name CAS# Ingredient Percent Bisphenol A diglycidyl ether resin by Weight EC Index Number: 1 SECTION 3 : HAZARDS IDENTIFICATION Emergency Overview: Potential Sensitizer. Irritant. Applies to All Ingredients : Route of Exposure: Potential Health Effects: Skin Contact: Eye and skin contact Moderate irritant (stinging, burning sensation, tearing, redness, swelling). Contact at elevated temperatures can cause thermal burns which may result in permanent damage or blindness. Moderate irritant. Contact at elevated temperatures can cause thermal burns which may result in permanent damage. May cause skin sensitization (itching, redness, rashes, hives, burning, swelling). The low vapor pressure of the resin makes inhalation unlikely in normal use. In applications where vapors (caused by high temperature) or mists

5 (caused by mixing) are created, breathing may cause a mild burning sensation in the nose, throat and lungs. Acute oral toxicity is low. May cause gastric distress (nausea, vomiting, diarrhea). Chronic Health Effects: Prolonged or repeated skin contact may cause sensitization, with itching, swelling, or rashes on later exposure. Other Potential Health Effects: See section 11. Aggravation of Pre-Existing Preexisting eye and skin disorders. Development of preexisting skin or Conditions: lung allergy symptoms may increase. SECTION 4 : FIRST AID MEASURES Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Get immediate medical attention. Skin Contact: Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while removing contaminated clothing and shoes. Get medical attention if irritation develops or persists. If inhaled, remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical attention. If swallowed, do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person. SECTION 5 : FIRE FIGHTING MEASURES Flash Point: Flash Point Method: Upper Flammable or Explosive Lower Flammable or Explosive Auto Ignition Temperature: Extinguishing Media: Unsuitable Media: Fire Fighting Instructions: Protective Equipment: Unusual Fire Hazards: >400 F (204.4 C) Pensky-Martens Closed Cup Use carbon dioxide (CO2) or dry chemical when fighting fires involving this material. Water or foam may cause frothing. Evacuate area of unprotected personnel. Use cold water spray to cool fire exposed containers to minimize risk of rupture. Do not enter confined fire space without full protective gear. If possible, contain fire run-off water. As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear. Sealed containers at elevated temperatures may rupture explosively due to polymerization and/or pressure build up and spread fire. Heating above 300 deg F in the presence of air may cause slow oxidative decomposition and above 500 deg F may cause polymerization. SECTION 6 : ACCIDENTAL RELEASE MEASURES Leak Response: Personal Precautions: Spill Cleanup Measures: Environmental Precautions: Large Spill: Avoid personal contact and breathing vapors or mists. Ventilate area. Use proper personal protective equipment as listed in section 8. Evacuate area and keep unnecessary and unprotected personnel from entering the spill area. Dike, contain, and soak up with an absorbent such as clay, sand, vermiculite, or other inert suitable material and dispose of properly. After removal, flush spill area with soap and water to remove trace residue. Avoid runoff into storm sewers, ditches, and waterways. Pump or shovel to storage/salvage vessels. SECTION 7 : HANDLING and STORAGE Handling: Storage: Hygiene Practices: Use with adequate ventilation. Avoid breathing vapor, aerosol or mist. Store in a cool, dry, well ventilated area away from sources of heat, combustible materials, and incompatible substances. Keep container tightly closed when not in use. Wash thoroughly after handling. SECTION 8 : EXPOSURE CONTROLS, PERSONAL PROTECTION Engineering Controls: Use appropriate engineering control such as process enclosures, local exhaust ventilation, general dilution ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Where such systems are not effective wear suitable personal protective equipment, which performs satisfactorily and meets OSHA or other recognized standards. Consult with local procedures for selection, training, inspection and maintenance of the personal protective equipment. Skin Protection Description: Wear appropriate protective gloves and other protective apparel to prevent skin contact. Hand Protection Description: Wear appropriate protective gloves. Consult glove manufacturer's data for permeability data. Eye/Face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR , OSHA eye and face protection regulation, or the European standard EN 166. Respiratory Protection: A NIOSH approved air-purifying respirator with an organic vapor/particulates combination cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any

6 Other Protective: Ingredient Guidelines Ingredient: Bisphenol A diglycidyl ether resin potential for an uncontrolled release, exposure levels are not known, or any other circumstances where air purifying respirators may not provide adequate protection. Facilities storing or utilizing this material should be equipped with an eyewash and a deluge shower safety station. OSHA PEL-TWA ACGIH TLV-STEL OSHA PEL-STEL ACGIH TLV-TWA SECTION 9 : PHYSICAL and CHEMICAL PROPERTIES Color: Clear. Odor: Little. Physical State: Viscous liquid. ph: Neutral. Vapor Pressure: 0.03 F Vapor Density: >1 (air = 1) Boiling Point: >500 F (260 C) Melting Point: Solubility in Water: Negligible. Specific Gravity: 1.17 Evaporation Point: <<1 (butyl acetate = 1) Percent Volatile: 0 Volatile Organic Compound 0 g/l Content: Molecular Formula: Molecular Weight: Percent Solids by Weight 100 SECTION 10 : STABILITY and REACTIVITY Chemical Stability: Conditions to Avoid: Incompatibilities with Other Materials: Hazardous Polymerization: Stable under normal conditions. Open flame and extreme heat Strong Lewis or mineral acids, strong oxidizing agents, strong mineral and organic bases (esp. primary and secondary aliphatic amines). will not SECTION 11 : TOXICOLOGICAL INFORMATION Bisphenol A diglycidyl ether resin : Eye Effect: No data available Skin Effects: Skin - rat LD: >2 gm/kg - [Nutritional and Gross Metabolic - other changes](rtecs) Ingestion Effects: Oral - rat LD: >5 gm/kg - [Nutritional and Gross Metabolic - other changes] (RTECS) Inhalation Effects: No data available SECTION 12 : ECOLOGICAL INFORMATION Ecotoxicity: Environmental Fate: No ecotoxicity data was found for the product. No environmental information found for this product. SECTION 13 : DISPOSAL CONSIDERATIONS Waste Disposal: Ignitable (Yes/No): Consult with the US EPA Guidelines listed in 40 CFR Part for the classifications of hazardous waste prior to disposal. Furthermore, consult with your state and local waste requirements or guidelines, if applicable, to ensure compliance. Arrange disposal in accordance to the EPA and/or state and local guidelines. No SECTION 14 : TRANSPORT INFORMATION DOT Shipping Name: DOT UN Number: Non-regulated Non-regulated

7 SECTION 15 : REGULATORY INFORMATION Bisphenol A diglycidyl ether resin : TSCA 8(b): Inventory Status: Canada DSL: SECTION 16 : ADDITIONAL INFORMATION MSDS Revision Date: 09/06/2006 MSDS Author: Actio Corporation Disclaimer: This Health and Safety Information is correct to the best of our knowledge and belief at the date of its publication but we cannot accept liability for any loss, injury or damage which may result from its use. The information given in the Data Sheet is designed only as a guidance for safe handling, storage and the use of the substance. It is not a specification nor does it guarantee any specific properties. All chemicals should be handled only by competent personnel, within a controlled environment. Copyright Actio Corporation. All Rights Reserved.