Assembly and Operating Manual PHL 2-finger parallel gripper

Transcription

1 Translation of original operating manual Assembly and Operating Manual PHL 2-finger parallel gripper

2 Imprint Imprint Copyright: This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights reserved. Any reproduction, processing, distribution (making available to third parties), translation or other usage - even excerpts - of the manual is especially prohibited and requires our written approval. Technical changes: We reserve the right to make alterations for the purpose of technical improvement. Document number: Version: /05/2018 en SCHUNK GmbH & Co. KG All rights reserved. Dear Customer, thank you for trusting our products and our family-owned company, the leading technology supplier of robots and production machines. Our team is always available to answer any questions on this product and other solutions. Ask us questions and challenge us. We will find a solution! Best regards, Your SCHUNK team SCHUNK GmbH & Co. KG Spann- und Greiftechnik Bahnhofstr D Lauffen/Neckar Tel Fax info@de.schunk.com schunk.com 2

3 Table of contents Table of contents 1 General About this manual Presentation of Warning Labels Applicable documents Sizes Variants Warranty Scope of delivery Accessories Basic safety notes Intended use Not intended use Constructional changes Spare parts Gripper fingers Environmental and operating conditions Personnel qualification Personal protective equipment Notes on safe operation Transport Malfunctions Disposal Fundamental dangers Protection during handling and assembly Protection during commissioning and operation Protection against dangerous movements Notes on particular risks Technical Data Assembly Mechanical connection Assembly of the top jaws Air connection Mounting the sensor Overview of sensors Inductive proximity switch IN Magnetic switch MMS 22 / RMS Mount the programmable magnetic switch MMS 22-PI Troubleshooting Module does not move?

4 Table of contents 5.2 The module does not travel through the entire stroke? Module opens or closes abruptly? The gripping force drops? Module does not achieve the opening and closing times? Maintenance Notes Exchanging the rail and base jaws version G Exchanging the rail and base jaws version W Maintencance of module with gripping force maintenance Maintenance and lubrication intervals Lubricants/Lubrication points (basic lubrication) Disassembly and assembly Version without gripping force maintenance Variant with gripping force maintenance Servicing and assembling the module Screw tightening torques Assembly drawing Translation of original declaration of incorporation Annex to Declaration of Incorporation

5 1 General General 1.1 About this manual This manual contains important information for a safe and appropriate use of the product. This manual is an integral part of the product and must be kept accessible for the personnel at all times. Before starting work, the personnel must have read and understood this operating manual. Prerequisite for safe working is the observance of all safety instructions in this manual. Illustrations in this manual are provided for basic understanding and may differ from the actual product design. In addition to these instructions, the documents listed under Applicable documents [} 6] are applicable Presentation of Warning Labels To make risks clear, the following signal words and symbols are used for safety notes. DANGER Danger for persons! Non-observance will inevitably cause irreversible injury or death. WARNING Dangers for persons! Non-observance can lead to irreversible injury and even death. CAUTION Dangers for persons! Non-observance can cause minor injuries. NOTICE Material damage! Information about avoiding material damage. 5

6 General Applicable documents Sizes General terms of business * Catalog data sheet of the purchased product * Assembly and Operating manuals of the accessories * The documents marked with an asterisk (*) can be downloaded on our homepage This operating manual applies to the following sizes: PHL 25 PHL 32 PHL 40 PHL 50 PHL Variants This operating manual applies to the following variations: PHL Sliding bearing version (-G) PHL Roller bearing version (-W) PHL with gripping force maintenance -S PHL High-temperature (V/HT) 1.2 Warranty If the product is used as intended, the warranty is valid for 24 months from the ex-works delivery date under the following conditions: Observe the specified maintenance and lubrication intervals Observe the ambient conditions and operating conditions Parts touching the workpiece and wear parts are not included in the warranty. 1.3 Scope of delivery The scope of delivery includes 2-finger parallel gripper PHL in the version ordered Assembly and Operating Manual Accessory pack 6

7 General 1.4 Accessories A wide range of accessories are available for this product For information regarding which accessory articles can be used with the corresponding product variants, see catalog data sheet. Content of the sealing kit: 4x Moulded seal 4x O-ring 4x Quad ring (Size 25) 4x Cylinder seal (Size 32, 40,50, 63) ID.-No. of the seal kit Size ID number PHL PHL V/HT PHL PHL PHL PHL PHL

8 Basic safety notes 2 Basic safety notes 2.1 Intended use The product is designed exclusively for gripping and temporarily holding workpieces or objects. The product may only be used within the scope of its technical data, Technical Data [} 15]. When implementing and operating components in safety-related parts of the control systems, the basic safety principles in accordance with DIN EN ISO apply. The proven safety principles in accordance with DIN EN ISO also apply to categories 1, 2, 3 and 4. The product is intended for installation in a machine/system. The applicable guidelines must be observed and complied with. The product is intended for industrial and industry-oriented use. Appropriate use of the product includes compliance with all instructions in this manual. 2.2 Not intended use It is not intended use if the product is used, for example, as a pressing tool, stamping tool, lifting gear, guide for tools, cutting tool, clamping device or a drilling tool. Any utilization that exceeds or differs from the appropriate use is regarded as misuse. 2.3 Constructional changes Implementation of structural changes By conversions, changes, and reworking, e.g. additional threads, holes, or safety devices can impair the functioning or safety of the product or damage it. Structural changes should only be made with the written approval of SCHUNK. 2.4 Spare parts Use of unauthorized spare parts Using unauthorized spare parts can endanger personnel and damage the product or cause it to malfunction. Use only original spare parts or spares authorized by SCHUNK. 8

9 Basic safety notes 2.5 Gripper fingers Requirements for the gripper fingers Stored energy within the product creates the risk of serious injuries and significant property damage. Arrange the gripper fingers in a way that the product reaches either the position "open" or "closed" in a de-energized state. Only exchange the gripper fingers when no residual energy remains in the product. Make sure that the product and the top jaws are a sufficient size for the application. 2.6 Environmental and operating conditions Required ambient conditions and operating conditions Incorrect ambient and operating conditions can make the product unsafe, leading to the risk of serious injuries, considerable material damage and/or a significant reduction to the product's life span. See also Technical Data [} 15]. 2.7 Personnel qualification Inadequate qualifications of the personnel If the personnel working with the product is not sufficiently qualified, the result may be serious injuries and significant property damage. All work may only be performed by qualified personnel. Before working with the product, the personnel must have read and understood the complete assembly and operating manual. Observe the national safety regulations and rules and general safety instructions. Trained electrician Qualified personnel Instructed person Service personnel of the manufacturer The following personal qualifications are necessary for the various activities related to the product: Due to their technical training, knowledge and experience, trained electricians are able to work on electrical systems, recognize and avoid possible dangers and know the relevant standards and regulations. Due to its technical training, knowledge and experience, qualified personnel is able to perform the delegated tasks, recognize and avoid possible dangers and knows the relevant standards and regulations. Instructed persons were instructed by the operator about the delegated tasks and possible dangers due to improper behaviour. Due to its technical training, knowledge and experience, service personnel of the manufacturer is able to perform the delegated tasks and to recognize and avoid possible dangers. 9

10 Basic safety notes 2.8 Personal protective equipment Use of personal protective equipment Personal protective equipment serves to protect staff against danger which may interfere with their health or safety at work. When working on and with the product, observe the occupational health and safety regulations and wear the required personal protective equipment. Observe the valid safety and accident prevention regulations. Wear protective gloves to guard against sharp edges and corners or rough surfaces. Wear heat-resistant protective gloves when handling hot surfaces. Wear protective gloves and safety goggles when handling hazardous substances. Wear close-fitting protective clothing and also wear long hair in a hairnet when dealing with moving components. 2.9 Notes on safe operation Incorrect handling of the personnel Incorrect handling and assembly may impair the product's safety and cause serious injuries and considerable material damage. Avoid any manner of working that may interfere with the function and operational safety of the product. Use the product as intended. Observe the safety notes and assembly instructions. Do not expose the product to any corrosive media. This does not apply to products that are designed for special environments. Eliminate any malfunction immediately. Observe the care and maintenance instructions. Observe the current safety, accident prevention and environmental protection regulations regarding the product's application field Transport Handling during transport Incorrect handling during transport may impair the product's safety and cause serious injuries and considerable material damage. When handling heavy weights, use lifting equipment to lift the product and transport it by appropriate means. Secure the product against falling during transportation and handling. Stand clear of suspended loads. 10

11 Basic safety notes 2.11 Malfunctions Behavior in case of malfunctions Immediately remove the product from operation and report the malfunction to the responsible departments/persons. Order appropriately trained personnel to rectify the malfunction. Do not recommission the product until the malfunction has been rectified. Test the product after a malfunction to establish whether it still functions properly and no increased risks have arisen Disposal Handling of disposal The incorrect handling of disposal may impair the product's safety and cause serious injuries as well as considerable material and environmental harm. Follow local regulations on dispatching product components for recycling or proper disposal Fundamental dangers General Observe safety distances. Never deactivate safety devices. Before commissioning the product, take appropriate protective measures to secure the danger zone. Disconnect power sources before installation, modification, maintenance, or calibration. Ensure that no residual energy remains in the system. If the energy supply is connected, do not move any parts by hand. Do not reach into the open mechanism or movement area of the product during operation Protection during handling and assembly Incorrect handling and assembly Incorrect handling and assembly may impair the product's safety and cause serious injuries and considerable material damage. Have all work carried out by appropriately qualified personnel. For all work, secure the product against accidental operation. Observe the relevant accident prevention rules. Use suitable assembly and transport equipment and take precautions to prevent jamming and crushing. 11

12 Basic safety notes Incorrect lifting of loads Falling loads may cause serious injuries and even death. Stand clear of suspended loads and do not step into their swiveling range. Never move loads without supervision. Do not leave suspended loads unattended Protection during commissioning and operation Falling or violently ejected components Falling and violently ejected components can cause serious injuries and even death. Take appropriate protective measures to secure the danger zone. Never step into the danger zone during operation Protection against dangerous movements Unexpected movements Residual energy in the system may cause serious injuries while working with the product. Switch off the energy supply, ensure that no residual energy remains and secure against inadvertent reactivation. Never rely solely on the response of the monitoring function to avert danger. Until the installed monitors become effective, it must be assumed that the drive movement is faulty, with its action being dependent on the control unit and the current operating condition of the drive. Perform maintenance work, modifications, and attachments outside the danger zone defined by the movement range. To avoid accidents and/or material damage, human access to the movement range of the machine must be restricted. Restrict unintentional access by persons to this range e.g. via a protective cover, protective fence or photoelectric barrier. The protective cover and protective fence must be rigid enough to withstand the maximum possible movement energy. EMER- GENCY STOP switches must be easily and quickly accessible. Check the function of the EMREGENCY STOP before starting up the machine or system. If this protective equipment is not working properly, prevent the operation of the machine. 12

13 Basic safety notes 2.14 Notes on particular risks DANGER Risk of fatal injury from suspended loads! Falling loads can cause serious injuries and even death. Stand clear of suspended loads and do not step within their swiveling range. Never move loads without supervision. Do not leave suspended loads unattended. Wear suitable protective equipment. WARNING Risk of injury from objects falling and being ejected! Falling and ejected objects during operation can lead to serious injury or death. Take appropriate protective measures to secure the danger zone. WARNING Risk of injury due to unexpected movements! If the power supply is switched on or residual energy remains in the system, components can move unexpectedly and cause serious injuries. Before starting any work on the product: Switch off the power supply and secure against restarting. Ensure that no residual energy remains in the system. WARNING Risk of injury from crushing and impacts! Serious injury could occur during the base jaw procedure and when breaking or loosening the gripper fingers. Wear suitable protective equipment. Do not reach into the open mechanism or the movement area of the product. WARNING Risk of injury from sharp edges and corners! Sharp edges and corners can cause cuts. Use suitable protective equipment. 13

14 Basic safety notes WARNING Risk of injury due to spring forces! Parts are under spring tension on products which clamp using spring force or which have gripping force maintenance. While disassembling components can move unexpectedly and cause serious injuries. Disassemble the product cautiously. Make sure that no residual energy remains in the system. WARNING Risk of injury from objects falling during energy supply failure Products with a mechanical gripping force maintenance can, during energy supply failure, still move independently in the direction specified by the mechanical gripping force maintenance. Secure the end positions of the product with SCHUNK SDV-P pressure maintenance valves. 14

15 3 Technical Data Technical Data Designation PHL Pressure medium Compressed air, compressed air quality according to ISO :7 4 4 Nominal working pressure [bar] 6 Min. pressure [bar] without gripping force maintenance 2 with gripping force maintenance 4 Max. pressure [bar] without gripping force maintenance with gripping force maintenance 8 6,5 Designation PHL Ambient temperature [ C] min. max IP protection class* 41 Noise emission [db(a)] 70 * For use in dirty ambient conditions (e.g. sprayed water, vapors, abrasion or processing dust) SCHUNK offers corresponding product options as standard. SCHUNK also offers customized solutions for special applications in dirty ambient conditions. More technical data is included in the catalog data sheet. Whichever is the latest version. 15

16 Assembly 4 Assembly 4.1 Mechanical connection WARNING Risk of injury when the machine/system moves unexpectedly! Switch off power supply. Check the evenness of the bolting surface Mounting The values relate to the entire bolting surface. Requirements for levelness of the bolting surface (Dimensions in mm) Diameter Permissible unevenness < 100 < 0.02 > 100 < 0.05 The module can be mounted in 2 ways: A: Screws (1) are screwede thourgh the housing. B: Screws (2) are screwed in the threads The centering sleeves (3) are included in the accessory pack. NOTICE During assembly the minimum depth of engagement must be observed. The minimum depth of engagement is equal to 1.5 times the thread diameter. 16

17 Assembly Mounting material Item Mounting PHL 25 PHL 32 PHL 40 PHL 50 PHL 63 1 Thread diameter for mounting A M4 M5 M6 M6 M8 2 Thread diameter for mounting B M5 M6 M8 M8 M10 Thread length in the housing [mm]

18 Assembly 4.2 Assembly of the top jaws Mounting material The centering sleeves (2) are included in the scope of delivery. The screws for mounting the top jaws must be ordered by the customer: NOTICE Damaging of the gripper, if the maximum depth of engagement is exceeded. The minimum depth of engagement is equal to 1.5 times the thread diameter. Mounting PHL 25 PHL 32 PHL 40 PHL 50 PHL 63 Thread diameter M4 M4 M5 M6 M8 Max. depth of engagement for finger ,5 16 fastening [mm] Required number of screws per jaw [piece] Maximum tightening torque [Nm] 5,3 5,

19 Assembly 4.3 Air connection WARNING Risk of injury when the machine/system moves unexpectedly! Switch off power supply. NOTICE Damage to the gripper is possible! If the maximum permissible finger weight or the permissible mass moment of inertia of the fingers is exceeded, the gripper can be damaged. A jaw movement always has to be without jerks and bounce. You must therefore implement sufficient reduction and/or damping. Observe the diagrams and information in the catalog data sheet. NOTICE The gripper will be destroyed if more than one main connection is connected: Only use one of the two main connections (A, B) at a time. NOTICE Observe the requirements for the air supply Technical Data [} 15]. Open only the air connections that are needed. Close unused main air connections using the screw plugs from the enclosed pack. For a hose-free direction connection, use the O-rings from the enclosed pack. When using self-designed top jaws, it has to be ensured, that the main connection A opens the gripper, and main connection B closes the gripper. 19

20 Assembly Air connection 1 Main connections (Schlauchanschluss) (A= open, B = closed) 2 Hose-free direct connection (bodenseitig) (a= open, b = closed) 4.4 Mounting the sensor NOTE Observe the assembly and operating manual of the sensor for mounting and connecting. The product is prepared for the use of sensors. For the exact type designations of suitable sensors, please see catalog datasheet and Link Übersicht Sensoren. For technical data for the suitable sensors, see assembly and operating manual and catalog datasheet. The assembly and operating manual and catalog datasheet are included in the scope of delivery for the sensors and are available at schunk.com. Information on handling sensors is available at schunk.com or from SCHUNK contact persons. 20

21 Assembly Overview of sensors Designation PHL Inductive proximity switch IN 80 X X X X X Magnetic switch MMS 22 X X X X X Reed switch RMS X - - Programmable magnetic switch MMS-22 PI1 X X X X X Inductive proximity switch IN 80 Connection example for IN 80 1 brown 2 black 3 blue Types that can be ordered (see catalog): IN 80-S-M8 (switching function: closer) IN 80-S-M12 (switching function: closer) The inductive proximity switches used are equipped with reverse polarity protection and are short-circuit-proof. Make sure that you handle the proximity switches properly: Do not pull on the cable. Do not allow the sensor to dangle from the cable. Do not overtighten the mounting screw or mounting clip. Please adhere to a permitted bend radius of the cable. ( catalog) Avoid contact of the proximity switches with hard objects and with chemicals, in particular nitric acid, chromic acid and sulphuric acid. 21

22 Assembly The inductive proximity switches are electronic components, which can react sensitively to high-frequency interference or electromagnetic fields. Check to make sure that the cable is fastened and installed correctly. Provide for sufficient clearance to sources of high-frequency interference and their supply cables. Parallel switching of several sensor outputs of the same type (npn, pnp) is permissible, but does not increase the permissible load current. Note that the leakage current of the individual sensors (ca. 2 ma) is cumulative. Assembly of the mounting kit for IN80 Groove PHL 25-G PHL PHL PHL PHL 25-W 32-G 32-W 40-G PHL 40-W PHL PHL PHL 50-G 50-W 63-G PHL 63-W 1 x x x x x x x 2 x x x Gripper open: Ø Set the gripper to the "open" position. Ø Fasten the control cam (1) to the bridge using screws (2). Ø Screw T-nut (3) and bracket (4) together with the screws (5). Ø Slide T-nut and bracket into one of the grooves of the housing (see tab.). Ø Insert proximity switch (6) into bracket (4) as far as it will go. Ø Slide the proximity switch (incl. bracket and T-nut) towards the center of the gripper from the side where the top jaw is positioned until the proximity switch switches. Ø Clamp the proximity switch in this position by tightening the screws (5). Ø Close the gripper and open it again in order to test its functioning. 22

23 Assembly Gripper closed: Ø Set the gripper to the "closed" position. Ø Fasten the control cam (1) to the bridge with the screw (2). Ø Screw T-nut (3) and bracket (4) together with the screws (5). Ø Slide T-nut and bracket into one of the grooves of the housing (see tab.). Ø Insert proximity switch (7) into bracket (4) as far as it will go. Ø Slide the proximity switch (incl. bracket and T-nut) from the center of the gripper outwards until the proximity switch switches. Ø Clamp the proximity switch in this position by tightening the screws (5). Ø Open the gripper and close it again in order to test its functioning. Part gripped (O.D. gripping): Ø Proceed as described in "Gripper closed". Part gripped (I.D. gripping): Ø Proceed as described in "Gripper open" Magnetic switch MMS 22 / RMS 22 NOTICE Material damage due to an incorrect tightening torque! If the threaded pin is tightened with an incorrect tightening torque, the product may be damaged. Observe a maximum tightening torque of 10 Ncm for the setscrews. NOTE Ferromagnetic material changes the switching positions of the sensor. For example: Adapter plate made of ordinary steel. At ferromagnetic adapter plates: First mount the product on the adapter plate. Then set the position of the magnetic switch. The RMS sensors have a larger hysteresis than the MMS sensors. This means that short gripper strokes may not be able to be monitored with the RMS sensors. 23

24 Assembly Positioning the magnetic switch Positioning the magnetic switches Gripper open: Ø Set the gripper to the "Open" position. Ø Slide the magnetic switch (1) from the side closer to the jaw from the front into one of the grooves until the proximity switch switches. Ø Clamp the magnetic switch (1) in the groove in this position by tightening the set-screw. Ø Close the gripper and open it again in order to test its functioning. Gripper closed: Ø Set the gripper to the "Closed" position. Ø Slide the magnetic switch (2) from the side closer to the jaw from the front into one of the grooves until the proximity switch switches. Ø Clamp the magnetic switch (2) in the groove in this position by tightening the set-screw. Ø Open the gripper and close it again to test its functioning. Part gripped (O.D. gripping): Ø Clamp the part to be gripped. Ø Slide the magnetic switch (2) from the side closer to the jaw from the front into one of the grooves until the proximity switch switches. Ø Clamp the magnetic switch (2) in the groove in this position by tightening the set-screw. Ø Open the gripper and close it again to test its functioning. Part gripped (I.D. gripping): Ø Clamp the part to be gripped. Ø Slide the magnetic switch (2) from the side closer to the jaw from the front into one of the grooves until the proximity switch switches. Ø Clamp the magnetic switch (2) in the groove in this position by tightening the set-screw. Ø Open the gripper and close it again to test its functioning. 24

25 Assembly Mount the programmable magnetic switch MMS 22-PI1 NOTICE Risk of damage to the sensor during assembly! Observe a maximum tightening torque of 10 Ncm for the setscrews. Ø Bring gripper in the position in which it is to be set. Ø Hold teaching tool to the sensor 1 (1) until the sensor flashes. Ø Slide sensor 1 (1) into the groove (2), until the sensor 1 flashes rapidly. The optimal position is displayed. Ø Secure the sensor 1 (1) using the set-screw (4). Tightening torque: 10 Ncm Ø Hold teaching tool to the sensor 1 (1), to confirm the position. The sensor 1 (1) has been taught in. Ø Repeat steps for sensor 2. 25

26 Troubleshooting 5 Troubleshooting 5.1 Module does not move? Possible cause Corrective action Base jaws jammed on the rail, e.g. because Check the levelness of the bolting surface. the mounting surface is not even enough Mechanical connection [} 16] Loosen the mounting screws of the module and top jaws and actuate the module again. Pressure drops below minimum. Check the air supply. Air connection [} 19] Compressed air lines switched Check compressed air lines. Proximity switch defective or set incorrect. Repair the proximity switch. Unused air connections not closed. Close the unused air connections. Flow control valve closed. Open the flow control valve. Component is broken, e.g. through overloading with a repair order to SCHUNK. Ensure that Replace component or send the module the module was only used within its defined application parameters. Possible cause Pressure drops below minimum. Mounting surface is not even enough 5.2 The module does not travel through the entire stroke? Component is broken, e.g. through overloading 5.3 Module opens or closes abruptly? Possible cause Too little grease in the mechanical guiding areas of the module Compressed air lines are blocked Mounting surface is not even enough Possible cause Compressed air can escape 5.4 The gripping force drops? Too much grease in the mechanical motion spaces of the module Pressure drops below minimum. Corrective action Check the air supply. Air connection [} 19] Check the levelness of the bolting surface. Mechanical connection [} 16] Send the module to SCHUNK with a repair order or disassemble module. Corrective action Clean the module and relubricate it. Maintenance [} 28] Check the compressed air lines for crushing or damage. Check the levelness of the bolting surface. Corrective action Check seals, if necessary disassemble module and replace seals. Clean the module and relubricate it. Maintenance [} 28] Check the air supply. Air connection [} 19] 26

27 Troubleshooting Possible cause 5.5 Module does not achieve the opening and closing times? Compressed air lines are not installed optimally. Corrective action If present: Open the flow control couplings on the module to the maximum that the movement of the jaws occurs without bouncing and hitting. Check compressed air lines. Inner diameter of the compressed air lines are sufficiently large relative to the compressed air consumption Compressed air lines between module and control valve shoud be kept as short as possible. Flow rate of valve is sufficiently large relative to the compressed air consumption. NOTICE! The throttle check valve must not be removed, even if the gripper does not achieve the opening and closing times. If, despite of optimal air connections, the opening and closing times are not achieved according to the catalog, we recommend the use of quick exhaust valves direct at the module. 27

28 Maintenance 6 Maintenance 6.1 Notes Original spare parts When replacing damaged parts (wearing parts/spare parts) only use SCHUNK original spares Exchanging the rail and base jaws version G The base jaws of the guides are matched to each other. To have these parts replaced, send the complete rail system along with a repair order to SCHUNK or order the rail system set as a spare part Exchanging the rail and base jaws version W The carriages of the rail system are matched to each other and cannot be exchanged separately. Please order the complete rail system if a unit must be repaired Maintencance of module with gripping force maintenance You can carry out the maintenance and replace the seals yourself. We recommend having maintenance performed and the seals replaced at SCHUNK as the cover plate is under spring tension. 6.2 Maintenance and lubrication intervals NOTICE At ambient temperature above 60 C the lubricants can harden faster. Interval decrease accordingly. Maintenance intervals in Mio. cycles Size Seal replacement Lubrication of the slide rails Lubrication of the roller rails

29 Maintenance 6.3 Lubricants/Lubrication points (basic lubrication) SCHUNK recommends the lubricants listed. During maintenance, treat all greased areas with lubricant. Thinly apply lubricant with a lint-free cloth. Lubricant point Lubricant Metallic sliding surfaces microgleit GP 360 Sliding surfaces within the cylinder Fuchs Renolit HLT 2 All seals Fuchs Renolit HLT 2 Roller rail PHL 25 Mineral oil CLP (DIN 51517) ISO VG 32 to ISO VG 150 Roller rail PHL Bosch Dynalub 510 Depending on the load, the base jaws / carriages on the slide rail / roller rail can be relubricated as well, via lubrication nipples. The lubrication nipples can be used instead of the set-screw. The lubrication nipples can be used instead of the set-screw (arrows). The carriages of the roller system of type 25 may be re-lubricated via the openings on the front side of the carriages. 29

30 Maintenance The carriages of the rolling system of the types 32 to 63 may also be re-lubricated via a lubricating nipple. It is to be ensured that always the same grease is used in order to avoid gumming in the lubrication channels. Should a different grease be used, a compatibility test must be carried out. 6.4 Disassembly and assembly Version without gripping force maintenance Position of the position numbers Assembly drawing [} 34] WARNING Risk of injury when the machine/system moves unexpectedly! Remove the energy supplies. Make sure, that no residual energy remains in the system. NOTICE During removal! Do not damage the cylinder running surface when removing the piston. Ø Remove compressed air line. Ø Mark the position of the covers in order to prevent a mix up. Ø Unscrew screws (122) on both sides. Ø Remove cover (11) and centering sleeve (112) on both sides. Ø Remove seals (31). Ø Mark the position of the cylinder pistons. Ø Unscrew screws (120). Ø Pull out cylinder pistons (4), making sure that the cylinder running surface does not become damaged. 30

31 Maintenance Variant with gripping force maintenance Position of the item numbers Assembly drawing [} 34] WARNING Risk of injury due to unexpected movements! If the power supply is switched on or residual energy remains in the system, components can move unexpectedly and cause serious injuries. Before starting any work on the product: Switch off the power supply and secure against restarting. Ensure that no residual energy remains in the system. WARNING Risk of injury due to spring forces! The cover is under spring tension. Carefully disassemble the product. Ø Remove all compressed air lines. Ø Mark the position of the covers in order to avoid any inter-changing. Ø Remove locking screws or rather air connection from the main connection B (on both sides). Ø Mount a supply air throttle on the main connection side A and let the gripper move slowly into the end position. WARNING Risk of injury due to spring forces! The cover may be ejected due to high spring forces. Strictly observe the following instructions. Ø Preload the spring assembly via the opening of the main connection B by using a cylinder head screw (see tab.) until no more residual energy remains on the cover (2x). Ø Remove the compressed air hoses from main connection side A. Ø Carefully remove the cover screws (122). Ø Remove cover (12) and centering sleeve (112) on both sides. 31

32 Maintenance NOTICE Damage of the gripper if the cylinder running surface is damaged due to the spring assembly. Carefully remove spring assemblies. Ø Carefully remove the preloaded spring assemblies on both sides. Ø During maintenance keep the preloaded spring assemblies in a safe place where they are protected against dirt and external loading. Ø Remove seals (31). Ø Unscrew screws (121). Ø Pull out cylinder pistons (4), making sure that the cylinder running surface does not become damaged. Screws - when disassembling the variant with gripping force maintenance Size [stroke length] thread size/ strength class PHL 25 [30/45/60] PHL 32 [40/60/80] PHL 40 [50/75/100] PHL 50 [60/90/120] PHL 63 [80/120/160] M4 / 12.9 M4 / 12.9 M4 / 12.9 M6 / 12.9 M8 / 12.9 screw length Maintenance 6.5 Servicing and assembling the module Clean all parts thoroughly and check for damage and wear. Treat all greased areas with lubricant. Lubricants/Lubrication points (basic lubrication) [} 29] Oil or grease bare external steel parts. Replace all seals. The seals are in the enclosed sealing kit. Accessories [} 7] Assembly Position of the position numbers Assembly drawing [} 34] Assembly takes place in the opposite order to disassembly. Observe the following: Observe the installation position of the cylinder pistons (item 4) and the covers (11). Make sure the seals and cylinder running surfaces the are not damaged during pushing in the cylinder piston. Make sure that the cylinder piston is positioned in the centering collar of the gear rack (120/121) when tightening the screw. Unless otherwise specified, secure all screws and nuts with Loctite no. 243 and tighten with the appropriate tightening torque.screw tightening torques [} 33] 32

33 Maintenance Screw tightening torques Screw tightening torques Position of the position numbers Assembly drawing [} 34] Item PHL 25 PHL 32 PHL 40 PHL 50 PHL 63 Piston normal Nm 17.4 Nm 30.0 Nm 71.0 Nm 120 Nm Cover normal/gks 122, Nm 2.5 Nm 3.5 Nm 10.1 Nm 24.6 Nm Chain guide 123, Nm 5.9 Nm 5.9 Nm 5.9 Nm 10.1 Nm Actuator Nm 3.0 Nm 5.9 Nm 10.1 Nm 10.1 Nm Bridge Nm 3.0 Nm 5.9 Nm 5.9 Nm 10.1 Nm Fastening cover sheet Nm 1.27 Nm 1.27 Nm 1.27 Nm 1.27 Nm 33

34 Assembly drawing 7 Assembly drawing The following figures are example images. They serve for illustration and assignment of the spare parts. Variations are possible depending on size and variant. Assembly of the variant without gripping force maintenance * Included in the seal kit. Seal kit can only be ordered completely. 34

35 Translation of original declaration of incorporation 8 Translation of original declaration of incorporation in terms of the Directive 2006/42/EG, Annex II, Part 1.B of the European Parliament and of the Council on machinery. Manufacturer/ Distributor SCHUNK GmbH & Co. KG Spann- und Greiftechnik Bahnhofstr D Lauffen/Neckar We hereby declare that on the date of the declaration the following partly completed machine complied with all basic safety and health regulations found in the directive 2006/42/ EC of the European Parliament and of the Council on machinery. The declaration is rendered invalid if modifications are made to the product. Product designation: 2-finger parallel gripper / PHL / pneumatic ID number The partly completed machine may not be put into operation until conformity of the machine into which the partly completed machine is to be installed with the provisions of the Machinery Directive (2006/42/EC) is confirmed. Applied harmonized standards, especially: EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction The manufacturer agrees to forward on demand the relevant technical documentation for the partly completed machinery in electronic form to national authorities. The relevant technical documentation according to Annex VII, Part B, belonging to the partly completed machinery, has been created. Person authorized to compile the technical documentation: Robert Leuthner, Address: see manufacturer's address Lauffen/Neckar, December 2017 p.p. Ralf Winkler, Manager for development of gripping system components 35

36 Annex to Declaration of Incorporation 9 Annex to Declaration of Incorporation according 2006/42/EG, Annex II, No. 1 B 1.Description of the essential health and safety requirements pursuant to 2006/42/EC, Annex I that are applicable and that have been fulfilled with: Product designation 2-finger parallel gripper Type designation PHL ID number To be provided by the System Integrator for the overall machine Fulfilled for the scope of the partly completed machine Not relevant 1.1 Essential Requirements Definitions X Principles of safety integration X Materials and products X Lighting X Design of machinery to facilitate its handling X Ergonomics X Operating positions X Seating X 1.2 Control Systems Safety and reliability of control systems X Control devices X Starting X Stopping X Normal stop X Operational stop X Emergency stop X Assembly of machinery X Selection of control or operating modes X Failure of the power supply X 1.3 Protection against mechanical hazards Risk of loss of stability X Risk of break-up during operation X Risks due to falling or ejected objects X Risks due to surfaces, edges or angles X 36

37 Annex to Declaration of Incorporation 1.3 Protection against mechanical hazards Risks related to combined machinery X Risks related to variations in operating conditions X Risks related to moving parts X Choice of protection against risks arising from moving parts X Moving transmission parts X Moving parts involved in the process X Risks of uncontrolled movements X 1.4 Required characteristics of guards and protective devices General requirements X Special requirements for guards X Fixed guards X Interlocking movable guards X Adjustable guards restricting access X Special requirements for protective devices X 1.5 Risks due to other hazards Electricity supply X Static electricity X Energy supply other than electricity X Errors of fitting X Extreme temperatures X Fire X Explosion X Noise X Vibrations X Radiation X External radiation X Laser radiation X Emissions of hazardous materials and substances X Risk of being trapped in a machine X Risk of slipping, tripping or falling X Lightning X 1.6 Maintenance Machinery maintenance X Access to operating positions and servicing points X Isolation of energy sources X Operator intervention X Cleaning of internal parts X 37

38 Annex to Declaration of Incorporation 1.7 Information Information and warnings on the machinery X Information and information devices X Warning devices X Warning of residual risks X Marking of machinery X Instructions X General principles for the drafting of instructions X Contents of the instructions X Sales literature X The classification from Annex 1 is to be supplemented from here forward. 2 Supplementary essential health and safety requirements for certain X categories of machinery 2.1 Foodstuffs machinery and machinery for cosmetics or pharmaceutical X products 2.2 Portable hand-held and/or guided machinery X Portable fixing and other impact machinery X 2.3 Machinery for working wood and material with similar physical characteristics X 3 Supplementary essential health and safety requirements to offset hazards X due to the mobility of machinery 4 Supplementary essential health and safety requirements to offset hazards due to lifting operations X 5 Supplementary essential health and safety requirements for machinery intended for underground work X 6 Supplementary essential health and safety requirements for machinery presenting particular hazards due to the lifting of persons X 38

39 Notes Notes 39

40 40