Splicing or Lacing a Flat Belt, Pt. 1 Copyright 2016 by James P. Riser
|
|
- Briana Cobb
- 5 years ago
- Views:
Transcription
1 Splicing or Lacing a Flat Belt, Pt. 1 Copyright 2016 by James P. Riser I own several machines which utilize flat belt drives efficient and typical of their design era. In this multi-part document I shall describe a standard method of connecting belt ends. A big advantage of using flat belts and connecting the ends in the manner to be described is that the machines do not need to be disassembled to replace a worn belt. The method to be described places a series of steel hooks onto both belt ends. These ends are then connected by a pin to form a flexible joint. These joints allow for good belt tracking on the stepped cone pulleys and last possibly for decades. First to be shown are the required hooks. Hooks come in a range of sizes to accommodate belt thicknesses, widths, and environmental conditions. One hook size will not work for all sizes of belts. Hooks usually come in strips either 6 or 12 long. The user merely cuts off what is needed. Notice the cardboard or paper connecting strip. This keeps everything held in the proper position to mount within the lacer mechanism. Some brands have a steel connecting strip rather than paper to hold the hooks in position.
2 To further complicate things, all hook sizes will not fit all lacer mechanisms. This is a typical lacing mechanism termed a vice type as it is used with a vise to crimp the hooks. In operation, the hook segment to be used is inserted into the slots of the lacer. The slanted sides of the hooks will rest against the jaws of the crimper. The hooks get pushed well down into the mechanism. The long pin connected to the lacer slides into the brass comb and goes through the hooks to hold them securely in position.
3 Before showing the actual crimping of the belt hooks (shown in Part 2), I need to mention a few things about the lacer mechanisms. The mechanisms are for a range of belt thicknesses and a quick examination of the mechanism hinge will indicate the range of belt thicknesses the lacer can accommodate. The lacer to the left will only accommodate 1/8-3/16 thick belting. The lacer shown below will handle crimping hooks onto belts over 1/2 thick due to the sliding hinge arrangement. A ball point pen is inserted for size reference only. To the left is a close-up of this hinge. These hooks line up with the slots of the brass comb. This lacer will work with these hooks.
4 Notice how the hooks fit nicely into the comb. Here is another view. The hooks shown on the right do not line up with the slots in the brass comb. This lacer will not work with these hooks.
5 This is the belt joint that I will be replacing as the original belt length is now too long after the modifications I have made to the A.B. Knight lathe. The belt is clearly too long and needs to be shortened. In Part 2 I shall show how the hooks get crimped and the two belt ends get joined. It is important for the reader to understand from what I have shown here that the hook size must match the belt size and lacer mechanism. You can not just buy a lacer and hooks thinking they will work for your job. In a separate pdf I have assembled scans of some of the original old documentation that came with my hooks and lacers. The originals are falling apart and I wanted to preserve the information.
6 Part II On the old A. B. Knight lathe that I am restoring I chose to use the old leather belt that was on it as it still had plenty of life left in it. After moving he counter pulley up, the belt was way too long. The removed length of belting was used as a test piece to determine how many hooks I could get away with using for the new splice. I decide to try 6 hooks. A short length of 6 hooks was cut from this longer length. This short test strip was mounted in the lacer. After locking the hook strip in place with the long pin, the paper supports were removed leaving only hooks in the lacer. The lacer at this stage was ready to be placed into the vise.
7 The vise was opened just enough to allow the lacer with its hooks to drop down into it. You can see the ring end of the long pin which securely holds the hooks in position. The end of the belting test strip was cut square. This is necessary for reliable tracking of the belt in operation. The belt end was positioned in the hooks. Using the squaring tool, the belt was squared up within the hooks. The vise was closed to crimp the hooks onto the leather.
8 The experimental test strip with the 6 hooks looked like this unacceptable. The hooks were too close to the belting edges and the required hook offset could not be made as required for a good splice. So, things on the real belt to be used were setup for 5 hooks. The 5 hooks were crimped. Note the offset. The belt was placed into position, pulled tight, and marked. Allowance for hook length on the second belt end was subtracted from the marked length, and the belt was cut square. The cleaned up ends looked like this. Note the strip of stiff rawhide. A length of this would become the pin in the new splice. The rawhide comes in 6 lengths. Sometimes thick nylon cord is used.
9 The belt with its new hooks was placed in position over both pulleys and joined with the rawhide pin. The rawhide was cut to length with a utility knife. Here is the new splice. The interior of this 3/16 thick old belting is still good so I decided to use this belting until the new splice eventually fails in a few years. Below are shown two lacers. The larger one is the one used in this demonstration. The smaller one is only 2 long and is perfect for such 1 wide jobs. Shown to the right is this 2 lacer with a length of hooks inserted into the brass comb at its bottom.
A. TO PREPARE THE MACHINE FOR USE.
INSTRUCTION MANUAL FOR THE ML120 STRINGING MACHINE. CONTENTS: A. TO PREPARE THE MACHINE FOR USE. 1. The assembly of frame with console and tooltray. 2. Fixing the lever of the tension unit. 3. Putting
More informationThe author's TD Coupe, used as a towplane, and the Airhopper. The gas model is equipped with an automatic towline release.
THE AIRHOPPER BY STANLEY ORZECK PLANS BY PAUL PLECAN An eight-foot sailplane either towed by a gas model or launched by hand tow. The author's TD Coupe, used as a towplane, and the Airhopper. The gas model
More informationInstallation Instructions
116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting
More informationOWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)
OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most
More informationModel: 5100 OmniSteel Volleyball System
Model: 5100 OmniSteel Volleyball System Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS
More information[Title of the course]
As with non-metallic raceway, Hubbell metal raceway is available in a variety of styles. There are 13 metal raceway profiles 8 painted and 5 aluminum for customers to choose from! ALL Hubbell painted metal
More informationReach poles & cables system. product guide
Reach poles & cables system product guide Phantom Indoor Batting Cage reach poles & cables system This reach poles & cables system is engineered to maximize your interior space. This guide will walk you
More informationYour kit contains the following items. Additional Items You May Need. Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet
Your kit contains the following items Pre- cut parts Propeller rigging and rubber Sandpaper Covering sheet The SkyFox offers great glide performance in a rubber powered plane due to its built up wing.
More informationPR4 Installation, Operation & Maintenance Instructions (DOT Certification Included)
PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included) March 2006 Form FVC 054 Rev. 6 KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. The Passive - R4 device
More informationModel Copyright 2012 by General Machine Products (KT), LLC
LIGHTWEIGHT CAPSTAN WINCH OPERATION & MAINTENANCE MANUAL Model 70627 Copyright 2012 by All rights reserved. No part of this publication may be copied, reproduced or transmitted in any form whatsoever without
More informationPULLTARP INSTALLATION & OPERATORS MANUAL
PULLTARP INSTALLATION & OPERATORS MANUAL Step 1. Mounting Positions Determine the mounting position for your truck Fig. 1 - Fig. 7. Fig. 1 Fig. 2 Fig. 3 A Mount Top Or Bottom Roll B Mount Top Or Bottom
More informationU STAND INSTALLATION INSTRUCTIONS
U STAND INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new U STAND by Stand N Fish. Once installed on your kayak the U STAND will enhance your kayak fishing enjoyment to a whole new
More informationBOTTOM BRACKET BEARINGS
BOTTOM BRACKET BEARINGS This basic tutorial will demonstrate the workings of a typical 3 piece bottom bracket, showing the removal and installation of the various components that make up the bearing system.
More informationRefurbishing TR6 Window Slides. Chuck Hobbs 27 Feb 2017
Refurbishing TR6 Window Slides Chuck Hobbs 27 Feb 2017 Why Refurbish your Window Slides? Original slides are 40+ years old and are usually rusty, have no felt left on the runners and often the windows
More information" A " "B " F G H P PARTS LIST
K-57 SkyDart usiness SST Concept SUSIDIRY OF DMON ESTES INDUSTRIES PENROSE COLO. 8120 Designed by Larry H. Renger "G " " " " F " R "H " SP-57 U " " "C " I M C O T T L "D " E F G H P D J "E " N K Q S 1
More informationTHOR 10 HAMMER CAGE INSTRUCTIONS
75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the
More informationRudder Kit Assembly Instructions for Quest 13
Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you
More informationModel: 7200 Collegiate Volleyball System
Model: 7200 Collegiate Volleyball System Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS
More informationContents. Stainless Steel Side Block. 1.1 Separating the Side Block. Stainless Steel Side Block Reassembly of. Assembly from the Helmet Shell
Separating the Side Block Assembly from the Helmet Shell Contents SSB-1 SSB-3 SSB-5 SSB-5 SSB-7 1.1 Separating the Side Block Assembly from the Helmet Shell 1.2 Side Block Assembly Replacement 1.3 Defogger
More informationPrince Neos 1500 Review. Prince Neos A Review $
A $1395.00 The is a lock-out machine and the natural extension of the venerable Neos 1000 Neos genre that has been around for some time. This machine, at this price, is an entry level machine that you
More informationMake Your Own Bundled canes Revision Date: May 2014
Make Your Own Bundled canes Revision Date: May 2014 Attribution-ShareAlike 4.0 International (CC BY-SA 4.0) Summary: http://creativecommons.org/licenses/by-sa/4.0/ License: http://creativecommons.org/licenses/by-sa/4.0/
More informationCamRT Sun Top Bimini Installation Instructions
CamRT Sun Top Bimini Installation Instructions C910-07 & C910-08 Rev. 16-Jun-15 Information: info@roswellglobal.com Warranty: warranty@roswellglobal.com Questions? Please call us at (31) 638-1331 Setup:
More informationThe M-UPPT is an universal punch tool. Different punch inserts can be easily switched out. Pin to fix and remove inserts
The is an universal punch tool. Different punch inserts can be easily switched out. Pin to fix and remove inserts To install a punch insert, slide in the punch insert and fix this insert with the pin on
More informationHere's the comparison of the stock rock shaft vs. a 3pt rock shaft.
This documents a build of a Category 0 3 point hitch for the John Deere 316 Onan, 318, 322, 330, 332, 420 and 430 tractors. This is Neil Koch's build for his 318. Here's the comparison of the stock rock
More informationOwners Manual MAX-10/45 Upper Receiver. Rev. A. NFA Warning. LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204
Owners Manual MAX-10/45 Upper Receiver NFA Warning LAGE Manufacturing, L.L.C. 916 E. Baseline Rd. STE #113 Mesa, AZ 85204 CM109mk2-300 Rev. A This upper receiver is designed to be used with the M-10/45
More informationA Table Top Wind Tunnel You Can Build
A Table Top Wind Tunnel You Can Build Basic principles of aerodynamics can be studied in the classroom with this simple, inexpensive wind tunnel. All you need to build it is some cardboard boxes, glue,
More informationPRO1030 Bi-Directional Assembly Replacement
PRO1030 Bi-Directional Assembly Replacement 1. Remove both side covers using the Crank and Cover Removal procedure. Fig. 1 2. Disconnect both brake cables (not shown) from the brake (S3611). (Fig. 1) 3.
More informationImportant Safety Information for Users of. Bashlin Climbers
Important Safety Information for Users of Bashlin Climbers - WA R NING For your personal safety, this booklet must be completely read and all of the information understood completely before using these
More informationEnd. Standing Part. An underhand loop is made by crossing the end under the standing part.
Knot Board Learn to tie the four basic camping knots as illustrated as well as others you might add. Practice them until you can tie them well. Display them on a knot board made from a square of peg board
More informationCLIMBING Pads. Straps Gaffs Spikes Hardware
CLIMBING Pads Straps Gaffs Spikes Hardware Quick Change Aluminum Climbers CTB Tree and Pole Climbing Kit Kit with straps and L pads Patented design give these climbers strength, durability and style Utilizes
More informationRZR 900 Hitch Mount Plate
RZR 900 Hitch Mount Plate Polaris RZR 900 2015+ Part #: 5801119 Rev. 031017 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-278-7768 E-mail: sales-rtpro@sporttruckusainc.com SAFETY WARNING RT Pro
More informationicreasepro Creaser Operators Manual
6-2013 Version 3.0 icreasepro Creaser Operators Manual WWW.MBMCORP.COM 800-223-2508 TABLE OF CONTENTS SPECIFICATIONS.1a SAFETY PROCEDURES/CARE & MAINTENANCE..1b COMPONENT IDENTIFICATION 2 TOUCH SCREEN
More informationLock-N-Load. Bullet Feeder
Lock-N-Load Bullet Feeder table of contents steps Overview... 2 List of required hand tools... 2 1: Mounting the Bullet Feeder to the Bench... 3 2: Mounting the Bullet Feed Hopper... 4 3: Bullet Feed Hopper
More informationWorld s Most Versatile Home Gym
World s Most Versatile Home Gym View Newest Owner s Manual: Assembly Instructions Video: Installation Videos: https://gorilla-gym.com/owners-manual/ http://gorilla-gym.com/gorilla-gym-assembly-video/ http://gorilla-gym.com/how-it-works/installation-video/
More informationMelon-Shaped Egg Basket
Melon-Shaped Egg Basket GH PRODUCTIONS, INC. The Basket Maker's Catalog Materials are available from your basketry supply store, or contact: GH Productions, Inc. The Basket Maker's Catalog 521 E. Walnut
More informationStringway ML100 Review. Stringway ML100. A Review MSRP $1,195.00
Stringway ML100 A MSRP $1,195.00 The Stringway ML100 is a technical table top machine with features that are unique. The racquet support plate is adequate and the internal supports and hold down mechanics
More informationTHE GARRISON BINDER ...
Did you ever wonder why (to quote Andy Rooney) the Garrison binder is for many rodmakers the source of contentious problems while other rodmakers never seem to have problems. One of the primary reasons
More informationContinuous Finger-Over-Finger Bias Process
Instructions 1. Prepare both belt ends by calculating the 5:3 bias angle and ply separate with a Ply 130TM both belt ends to the required depth to accommodate selected finger length. Peak Belt Stop 2.
More informationOnly. Gives You the TechLock. System Advantage ASSEMBLY, DISASSEMBLY AND TROUBLESHOOTING INSTRUCTIONS FOR 3000 SERIES FONTAINE
April 00 Only Gives You the TechLock System Advantage ASSEMBLY, DISASSEMBLY AND TROUBLESHOOTING INSTRUCTIONS FOR 000 SERIES FONTAINE C o n n e c t y o u r b u s i n e s s w i t h F O N T A I N E April
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationMaking an old school lure
Powered by www.big-game-board.info Big Game Fishing Board tutorials presents Thank you very much to Bahama Lures. www.bahama-lures.com Making an old school lure I was inspired to do this by Jim Rizzuto's
More informationTrike-Bike Assembly Manual
Be sure to check our website for more instruction details, videos and photographs as well as a complete listing of each Nut and Bolt for the Trike Bike. www.trike-bike.com.au Go to the page marked ASSEMBLY
More informationPachinko Game (Additional Information)
Spiral Slide Lock Tab Front Door Brass Nails California Antique Slots, Inc. (805) 583-0785 (FAX) "Winner" Light Loader Levers Seesaw Covers Track Covers Bumpers Stickers Spinners Tulips Pockets Glass Cover
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationGel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions
Gel Drop Seal for FOSC 450 Fiber Optic Splice Enclosure Installation Instructions TECP-30-215 Issue 1 4/2013 INTRODUCTION The Gel Drop Seal device is for use with FOSC 450 B, B Short, C, and D size closures
More informationBabolat Star 5 Review. Babolat Star 5. A Review MSRP $
Babolat Star 5 A MSRP $3500.00 The Babolat Star 5 presents a technological and professional machine that uses the many years of Babolat development making this machine a reasonably priced option for any
More informationSoccer Goal. Model: SG20 Series. Installation, Operation and Maintenance Instructions
Soccer Goal Model: SG20 Series Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Model No. Description RP2300FC, RP2301FC Router CONCEPT AND MAIN APPLICATIONS Models RP2300FC and RP2301FC are upgraded sister tools of our current plunge-type electronic router Model
More informationChain Drives. 1. As no slip takes place during chain drive, hence perfect velocity ratio is obtained
1. Introduction Chain Drives In Belt and Rope drives slipping may occur. In order to avoid slipping, steel chains are used. The chains are made up of a number of rigid links which are hinged together by
More informationPay special attention to information provided in warnings, cautions and notes that are accompanied by one of these symbols:
TABLE OF CONTENTS General Information Outlaw / Rogue Components ModLock Connectors Waistband / Shoulder Strap Assembly Aircell Assembly ModLock Connector Disassembly Waistband Extender Double Cylinder
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. TD0101, TD0101F Description Impact Driver L PRODUCT P 1/ 14 CONCEPT AND MAIN APPLICATIONS Models TD0101 and TD0101F are cost-competitive 100N.m-class impact driver developed
More informationCHAPTER 5 REWIND STARTERS
GENERAL INFORMATION CHAPTER 5 REWIND S Rewind starters used on vertical shaft Tecumseh engines are top mount horizontal pull style or side mount vertical pull style. Horizontal shaft engines use side mounted
More informationOMS Comfort Harness II
Assembly of the Shoulder Pads OMS Comfort Harness II Take the larger of the two pieces of webbing (with grommet) and start at the top of the Back Plate: A) Thread the webbing thru the back slanted slots
More informationFalcon 3 145, 170, 195 and Tandem Owner / Service Manual
Falcon 3 145, 170, 195 and Tandem Owner / Service Manual January 2007 - Second Edition Removing The Sail From The Airframe And Short Packing The Glider Many maintenance and repair procedures will require
More informationCleaning rod: spring steel, stainless steel or carbon fibre cleaning rod - only use a one-piece rod. Avoid using snakes.
Telemark Biathlon Where performance and precision come together http://telemarkbiathlon.com Rifle Cleaning Date : July 19, 2013 Anschutz Rifle Manual - Click Here Izhmash 7-3 Rifle Manual - still looking
More information44in Side Discharge Mower for Wheel Horse XL 440H Lawn Tractors Model No Serial No and Up
Form No. 5-8 in Side Discharge Mower for Wheel Horse XL 0H Lawn Tractors Model No. 790 Serial No. 5000000 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN) Contents
More informationCABLES-ONLY SYSTEM PRODUCT GUIDE
CABLES-ONLY SYSTEM PRODUCT GUIDE Phantom Indoor Batting Cage CABLES-ONLY SYSTEM This cables-only system is engineered to maximize your interior space. This guide will walk you through setting up your wall
More informationAssembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
More information-SWEPT AWAY- Description & Overview. VEX Classroom Competition Swept Away
-SWEPT AWAY- Description & Overview Swept Away is a head-to-head robotics competition designed and scaled to be run in a classroom environment by a single teacher. This game provides a challenge for designers
More informationAlpha Ghost Review. Alpha Ghost. A Review MSRP $
Alpha Ghost A MSRP $2495.00 The Alpha Ghost represents the latest technology offering from a company that is well known for quality, value stringing machines. The Ghost incorporates the auto brake system
More informationMANUAL SEALLESS STEEL STRAPPING TOOL MODEL A
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A337.0001 13.1912.01 13191201.en/MAS/ 10.02 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 4 3 APPROPRIATE
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M)
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 3K Puller (M3K-M) 04/17 (M3K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR SERVICING THIS TOOL TABLE
More informationM&P Trigger Work. The S&W M&P may be one of the easiest guns ever to do trigger work on.
M&P Trigger Work The S&W M&P may be one of the easiest guns ever to do trigger work on. M&P Trigger Job Make sure the gun is unloaded. Follow normal field striping procedures. What needs to be changed
More informationThank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step*
PG 1 OF 9 PORTA-DOCK, INC. 74A ABL/APW 1056 & 44A FLB APW 1056 PORTA-LIFT Thank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step* STEP 1. Separate and group
More informationDK ton, Double-acting, Die-type Crimping Tool
INSTRUCTION MANUAL DK6040 60-ton, Double-acting, Die-type Crimping Tool Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationR.J.W. LTD. Motorised CNB USER MANUAL. 10. Safe Operation Procedure for cutting Charpy/Izod Notch
10. Safe Operation Procedure for cutting Charpy/Izod Notch 10mm Specimen with 2mm V Notch Caution notes a) DO NOT STALL THE MACHINE! ATTEMPTING TO CUT A MATERIAL WHICH IS TOO HARD OR USING A BROACH WHICH
More informationExperimental Procedure
1 of 15 9/13/2018, 12:47 PM https://www.sciencebuddies.org/science-fair-projects/project-ideas/sports_p060/sports-science/physics-of-baseball-hit-charts (http://www.sciencebuddies.org/science-fairprojects/project-ideas/sports_p060/sports-science/physics-of-baseball-hit-charts)
More informationStand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS
1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing
More information2010 International Snow Science Workshop
HOW TO TURN A KIDS BIKE INTO A BOMB TRAM FOR AVALANCHE CONTROL WORK David Immeker* Heavenly Mountain Resort Professional Ski Patrol, South Lake Tahoe, California ABSTRACT: Bomb trams have been used for
More informationTrue Tension Professional
True Tension Professional A *MSRP $3,000.00 *The True Tension Professional is a model that I have modified to include sixteen (16) racquet supports. In addition to the supports I am using clamps with no
More informationManufacturing, Inc. Manual. Series I UT3030, UT5036, UT5042 & UT5052 (S/N KA1096A-) Rolling Spike Update Ultra-Till (Disc & Coulter)
Manual Series I UT3030, UT5036, UT5042 & UT5052 (S/N KA1096A-) Rolling Spike Update Ultra-Till (Disc & Coulter) Manufacturing, Inc.! Read the operator s manual entirely. When you see this symbol, the subsequent
More informationOPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M)
OPERATING and MAINTENANCE INSTRUCTIONS MAXIS 6K Puller (M6K-M) READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND SAFETY INFORMATION IN THIS MANUAL BEFORE OPERATING OR 04/17 (M6K-M) SERVICING THIS TOOL TABLE
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationMisaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii
Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6
More informationXtender30. Home Batting Cage. Assembly Instructions
Xtender30 Home Batting Cage Assembly Instructions IMPORTANT DO NOT RETURN THIS BATTING CAGE TO THE RETAIL STORE WHERE PURCHASED. CALL TOLL FREE: (800) 492-9334 IMPORTANT WARRANTY WARNING: DO NOT LEAVE
More informationKnot Masters Program
The Knot Masters program helps Scouts to learn the knots they need for advancement, Scouters to become proficient in knot tying, and keeps knot tying skills sharp. Scouts and Scouters are encouraged to
More information8MAY15 US RACK, Inc Falcon Drive, Madera, CA
8MAY15 US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for Bedrail-mounted MOTORCYCLE RACK, Model 2001-4TRA WARNING: Do NOT attempt to install or use this rack without following
More informationAR-15 Rifle Operator Maintenance
AR-15 Rifle Operator Maintenance These procedures cover how to Clean, Inspect and Lubricate the AR15 Rifle NOTICE: This is not a replacement for the manufacturer s manual. If you do not have the owners
More informationAssembling Instruction - Triton Ladoga 1 advanced Allround touring and sea kayak
Assembling Instruction - Triton Ladoga 1 advanced Allround touring and sea kayak 1 Assembling Instruction - Triton Ladoga 1 advanced Dear Customer, At first: please do not be alarmed by the extent of these
More informationCHOCKS LOCOMOTIVES & RAIL CAR STOPPING DEVICES CAST STEEL WHEEL CHOCKS - INFO (MADE IN USA) MODEL NO.
CAST STEEL WHEEL CHOCKS - INFO (MADE IN USA) Why Use Wheel Chocks? A gust of wind is enough to cause a 118,000kg freight car to start rolling. Thanks to roller bearings, freight car wheels offer very little
More informationFiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual
Fiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 100 strand fiber - Bubbler 75 strand fiber - Spillway Light Bar 45 ft. fiber tail
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More informationELECTRIC TOOL PARTS LIST
Hitachi Power Tools LIST E933 ELECTRIC TOOL PARTS LIST SLIDE COMPOUND SAW Model 2004 2 13 (E2) 1 2 3 4 5 6 7 40 41 601 8 9 10 11 12 26 27 28 29 30 29 602 618 602 10 9 42 603 604 605 606 607 608 14 43 13
More informationVR1 Owner s Manual. Vigilance Rifles, Inc Plum Lane Redlands, CA P F
VR1 Owner s Manual Vigilance Rifles, Inc. 1653 Plum Lane Redlands, CA 92374 P 909.307.8877 F 909.307.8866 www.vigilancerifles.com INTRODUCTION: Vigilance Rifles offers a new line of Semi-Automatic Rifles
More informationLIQUIP DRYBREAK COUPLER. API800 Series MAINTENANCE INSTRUCTIONS
LIQUIP DRYBREAK COUPLER API800 Series MAINTENANCE INSTRUCTIONS API LOADING COUPLER TO API RP1004 June 2015 Issue: F M:\Product-Info\API8xx\6-Service-Maintenance\API800 MAINTENANCE INSTRUCTIONS 40183.doc
More informationINSERT FITTINGS INSERT FITTINGS
Insert Tee Insert x Female Tee Insert Elbow Insert x Male Elbow Insert Coupling Insert x Male Adapter Insert x Female Adapter Insert Plug POLY and NYLON FITTINGS For use with Poly Tubing Fitting 1/2 3/4
More informationParts Manual. Scraper Hitches PH:
Parts Manual Scraper Hitches 12-18 1 Table of Contents A123299 Swivel Hitch 3 A1063527 Super Swivel Hitch 4 A125056 Yoke Hitch 5 A125057 Super Capacity Hitch 6 A125223 MDU Hitch 7 A123224 360 Swivel Hitch
More informationK13.12 FACE FIXED PANIC EXIT DEVICE K13 DOORS
K13 DOORS K13.12 FACE FIXED PANIC EXIT DEVICE 01.03.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Base set n
More informationMiller Revolution Key Features
Thank you for purchasing the Miller Revolution Harness. The Revolution is an all new and totally innovative harness engineered with seven (7) unique components and more than eleven (11) key product features.
More informationWeightlifter Nacelle Only
Weightlifter Nacelle Only i n s t r u c t i o n s About KidWind The KidWind Project is a team of teachers, students, engineers, and practitioners exploring the science behind wind energy in classrooms
More informationPlace a rope coil here
1 2 3 4 The anchor buoys were made from Sculpey. You could however, carve them from wood but I wanted to continue my experimentation with this material. A buoy from this time period would have ranged from
More informationMUELLER. A Wall Type. Indicator Post. Reliable Connections. General Information 2. Technical Data/ Dimensions 3. Installation 4-5.
Installation Instructions manual MUELLER table of contents PAGE A-20814 Wall Type General Information 2 Technical Data/ Dimensions Installation 4-5 Maintenance 6 Parts 7 Indicator Post! WARNING: 1. Read
More informationFinal Assembly Instructions Bikes with 16 Wheel Size
Final Assembly Instructions Bikes with 16 Wheel Size Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert
More informationTsubaki Sprocket Capabilities
Tsubaki Sprocket Capabilities Introduction to Made-to-Order Sprockets At Tsubaki, our commitment is to bring you the highest value in the industry today. Period. And as a full line supplier of power transmission
More informationTECHNICAL INFORMATION ROPE ATTACHMENTS
TECHNICAL INFORMATION ROPE ATTACHMENTS WWW.SIEMAG-TECBERG.COM TECHNICAL INFORMATION ROPE ATTACHMENTS Head-rope attachments for single and multi-rope winding installations Balance-rope attachments for round
More informationA Low Cost Digital Angle Gage, version 3
A Low Cost Digital Angle Gage, version 3 By R. G. Sparber Copyleft protects this document. 1 Sometimes re-inventing the wheel has advantages. What you see here is just a variation on a sine bar. The accuracy
More informationCHAINLESS ANCHORING SYSTEM USER MANUAL
CHAINLESS ANCHORING SYSTEM USER MANUAL Introduction..................................................... 1 Setting up the Chainless Anchoring System............................ 4 Set up Procedure............................................
More informationReinforced connecting pin. Silver. 6.5mm. Black. 7.1mm
- SERVICE INSTRUCTIONS SI-R70C t Rear Drive System Before use, read these instructions carefully, and follow them for correct use. WARNING Use neutral detergent to clean the chain. Do not use alkali-based
More information