ST70+ Installation Guide

Transcription

1 87099_1.book Page Tuesday, January 27, :45 PM ST70+ Installaton Gude Document reference: Date: January 2009

2 87099_1.book Page Tuesday, January 27, :45 PM Autohelm, HSB, RayTech Navgator, Sal Plot, SeaTalk and Sportplot are UK regstered trademarks of Raymarne UK Lmted. Pathfnder and Raymarne are UK regstered trademarks of Raymarne Holdngs Lmted. 45STV, 60STV, AST, Autoadapt, AutoGST, AutoSeastate, AutoTrm, Bdata, G Seres, HDFI, LfeTag, Marne Intellgence, Maxvew, On Board, Raychart, Raynav, Rayplot, RayTalk, Raystar, ST40, ST60+, Seaclutter, Smart Route, Trdata and Waypont Navgaton are trademarks of Raymarne UK Lmted. All other product names are trademarks or regstered trademarks of ther respectve owners. Handbook contents copyrght Raymarne plc

3 87099_1.book Page Tuesday, January 27, :45 PM Contents Preface... v Warnngs and cautons...v Electromagnetc Compatblty (EMC) conformance...v EMC nstallaton gudelnes... v Remember... v Suppresson ferrtes... v Pressure washng...v Certfed nstallaton... x Product documents... x Techncal accuracy...x Product dsposal... x Chapter 1:Gettng started Introducton... 1 Certfed nstallaton... 1 Overvew... 1 Gettng assstance Plannng... 1 General nformaton... 1 Dsplays... 3 Functonalty... 3 Dmensons... 3 Keypads... 3 Power supples... 4 Dedcated dsplay power supply... 5 Postonng ST70+ dsplays & keypads... 5 Stng requrements... 5 Other consderatons Equpment & tools... 6 Parts suppled... 6 Parts not suppled... 8 Optonal cablng and connectors... 8 Chapter 2:Installaton Procedure...11 Cablng...11 Dsplay power cables SeaTalk ng connectons Mountng & connectng products Mountng optons Mountng procedure Connectng Installng transducers Transducer types Fttng Connectng Conventonal transducers Smart transducers Commssonng requrement... 17

4 87099_1.book Page v Tuesday, January 27, :45 PM v ST70+ Installaton Gude Chapter 3:Commssonng Procedures Introducton Requrement Autoplot calbraton Control nformaton Commonly used control functons Scrollng OK functon Select Dsplay Intal setup Swtch on Selectng language Settng Vessel Type Select type Settng dsplay types and groups Date & Tme Settng date format Settng tme format Settng local tme Leavng date & tme setup Data unts Changng unts Leavng unts setup: Intal setup end routne Next actons Docksde setup Autoplot system Docksde wzard Hard over tme End of autoplot docksde setup Transducer setup Introducton to transducer setup Accessng transducer setup Calbratng conventonal transducers Calbratng smart transducers Calbratng trm tabs End of transducer setup Mscellaneous setup Settng ground wnd Settng magnetc varaton Changng dsplay response rate Rudder lmt Settng rudder offset Next actons Open water calbraton Autoplots Startng open water calbraton Compass calbraton AutoLearn Requrement for a clear area Procedure Next actons... 45

5 87099_1.book Page v Tuesday, January 27, :45 PM Contents v Instrument system calbraton Prelmnary procedure Wnd transducer setup Speed calbraton Speed calbraton for conventonal speed transducer Speed calbraton for smart transducer Return to normal operaton Checkng autoplot operaton General Checkng rudder gan Checkng counter rudder Rudder dampng Settng AutoTrm After commssonng EMC conformance Appendx 1: Specfcatons Dsplay...55 Keypads...55 All types Instrument keypad Plot Controller (power boat) keypad Plot Controller (sal boat) keypad Index Templates... 59

6 87099_1.book Page v Tuesday, January 27, :45 PM v

7 87099_1.book Page v Tuesday, January 27, :45 PM v Contents Preface Warnngs and cautons WARNING: Product nstallaton & operaton Ths equpment must be nstalled, commssoned and operated n accordance wth the Raymarne nstructons provded. Falure to do so could result n personal njury, damage to your boat and/or poor product performance. WARNING: Swtch off power supply Ensure the boat s power supply s swtched OFF before startng to nstall ths product. Do NOT connect or dsconnect equpment wth the power swtched on, unless nstructed n ths document. WARNING: Ensure safe navgaton Ths product s ntended only as an ad to navgaton and must never be used n preference to sound navgatonal judgment. Only offcal government charts and notces to marners contan all the current nformaton needed for safe navgaton, and the captan s responsble for ther prudent use. It s the user s responsblty to use offcal government charts, notces to marners, cauton and proper navgatonal skll when operatng ths or any other Raymarne product. WARNING: Potental gnton source Ths product s NOT approved for use n hazardous/flammable atmospheres. Do NOT nstall n a hazardous/flammable atmosphere (such as n an engne room or near fuel tanks). CAUTION: Replaceable parts Ths product does not contan any user servceable parts. Please refer all repar requrements to an authorzed Raymarne dealer. Unauthorzed repars may affect your warranty. Electromagnetc Compatblty (EMC) conformance Raymarne equpment and accessores conform to the approprate Electromagnetc Compatblty (EMC) regulatons for use n the recreatonal marne envronment. Correct nstallaton s requred to ensure that EMC performance s not compromsed. Always check the nstallaton before gong to sea to make sure that t s not affected by rado transmssons, engne startng or other forms of nterference. To do ths: 1. Turn on all transmttng equpment (radar, VHF rado, etc). 2. Check that all electronc systems are unaffected by nterference from the transmttng equpment.

8 87099_1.book Page v Tuesday, January 27, :45 PM v ST70+ Installaton Gude EMC nstallaton gudelnes Raymarne equpment and accessores conform to the approprate Electromagnetc Compatblty (EMC) regulatons. Ths mnmzes electromagnetc nterference between equpment, whch could otherwse affect the performance of your system. Correct nstallaton s requred to ensure that EMC performance s not compromsed. For optmum EMC performance, we make the followng recommendatons: Place Raymarne equpment and cables at least 3 ft (1 m) from any equpment that transmts, or cables that carry, rado sgnals from VHF rados, cables and antennas. In the case of SSB rados, the dstance should be ncreased to 7 ft. (2 m). Place Raymarne equpment and cables more than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radatng element. Use a power source separate from that used for engne-start. Ths s mportant to prevent erratc behavor and data loss whch can occur f the engne-start does not have a separate battery. Use Raymarne-specfed cables. Do not cut or extend cables unless dong so s detaled n the nstallaton manual. Remember Where constrants on the nstallaton prevent any of the above recommendatons: Always allow the maxmum separaton possble between dfferent tems of electrcal equpment. Ths wll provde the best condtons for good EMC performance of the nstallaton. Suppresson ferrtes Raymarne cables may be ftted wth suppresson ferrtes. These are necessary for correct EMC performance. Any ferrte removed durng nstallaton must be replaced as soon as nstallaton s complete. Use only ferrtes of the correct type, suppled by Raymarne authorzed dealers. Connectons to other equpment If Raymarne equpment s to be connected to other equpment usng a cable not suppled by Raymarne, a Raymarne suppresson ferrte MUST always be attached to the cable near the Raymarne unt. Pressure washng Do NOT pressure wash any Raymarne product. Subjectng any Raymarne product to hgh pressure washng may cause subsequent water ntruson and falure of the product. Raymarne wll not warranty product subjected to hgh pressure washng.

9 87099_1.book Page x Tuesday, January 27, :45 PM Preface x Certfed nstallaton Raymarne recommends certfed nstallaton by a Raymarne approved nstaller. A certfed nstallaton qualfes for enhanced warranty benefts. Contact your Raymarne dealer for further detals and refer to the separate warranty document packed wth your product. Product documents Ths document s part of a seres of books assocated wth the ST70+. Product documents can be downloaded from ST70+ Installaton Gude (ths document). ST70+ Operatng Gude. Comprses operatng cards wth nstructons for day-today operaton of ST70+. ST70+ User Reference manual.ths s suppled as a PDF document on your ST70+ CDROM. It ncludes commssonng, setup and dagnostc nformaton. SeaTalk ng Reference Manual. Ths provdes detaled nformaton regardng SeaTalk ng connectvty. Techncal accuracy To the best of our knowledge, the nformaton n ths document was correct at the tme t was produced. However, Raymarne cannot accept lablty for any naccuraces or omssons t may contan. In addton, our polcy of contnuous product mprovement may change specfcatons wthout notce. As a result, Raymarne cannot accept lablty for any dfferences between the product and ths document. Product dsposal Waste Electrcal and Electronc (WEEE) Drectve The WEEE Drectve requres the recyclng of waste electrcal and electronc equpment. Whlst the WEEE Drectve does not apply to some of Raymarne's products, we support ts polcy and ask you to be aware of how to dspose of ths product. The crossed out wheele bn symbol, llustrated above, and found on our products sgnfes that ths product should not be dsposed of n general waste or landfll. Please contact your local dealer, natonal dstrbutor or Raymarne Techncal Servces for nformaton on product dsposal.

10 87099_1.book Page x Tuesday, January 27, :45 PM x ST70+ Installaton Gude

11 87099_1.book Page 1 Tuesday, January 27, :45 PM 1 Chapter 1: Gettng started 1.1 Introducton It s mportant that ST70+ products are nstalled correctly. For a safe and successful nstallaton, we recommend a certfed nstallaton. Certfed nstallaton Raymarne recommends certfed nstallaton by a Raymarne approved nstaller. A certfed nstallaton qualfes for enhanced warranty benefts. Contact your Raymarne dealer for further detals and refer to the separate warranty card packed wth your product. Overvew The key steps n the nstallaton procedure are: Plannng Plan your system. Decde where to locate the ST70+ products. Check parts. Installng Mount and connect the dsplays and keypads. Install the transducers. Fx equpment n place. Commsson the dsplays before use. Gettng assstance If you requre assstance wth nstallaton, please refer to your dealer and/or vst the Raymarne web ste at Plannng General nformaton An ST70+ system comprses one or more color dsplays, controlled by one or more keypads. These products are connected to the boat s SeaTalk ng system from whch they receve autoplot and transducer data. Refer to the SeaTalk ng System Reference Manual for nformaton on SeaTalk ng connectvty. In a SeaTalk ng system, dsplays and keypads are connected to the SeaTalk ng backbone usng spur cables. Transducers are also connected, ether va compatble pods or drectly, dependng on transducer type.

12 87099_1.book Page 2 Tuesday, January 27, :45 PM 2 ST70+ User Reference Manual ST70+ Instrument dsplays ST70+ Plot Controller dsplay 12V dc 12V dc 12V dc Wnd transducer Fuse Fuse Fuse Power Supply for ST70+ dsplays ST70+ Plot Controller keypad Transducer pod ST70+ Instrument keypad SeaTalk ng backbone SeaTalk ng Power Supply 12V dc 5-Way Connector SeaTalk ng backbone DST800 Smart transducer DT800 Smart transducer Note: Fgure 1-1: Typcal system See page 8 for nformaton about addtonal SeaTalk ng cables and accessores, ncludng the SeaTalk ng backbone kt. D

13 87099_1.book Page 3 Tuesday, January 27, :45 PM Chapter 1: Gettng started 3 Dsplays Functonalty The functonalty of each ST70+ dsplay s set up after nstallaton but before use, to determne whether the dsplay functons as ether an Instrument or a Plot Controller. Dmensons 6.0 n (152 mm) 7.44 n (189 mm) Fgure 1-2: Dsplay dmensons Keypads Three types of keypad are avalable, namely: Instrument keypad. Plot Controller keypad for power boats. Plot Controller keypad for sal boats n (6.5 mm) 1.66 n (42.3 mm) D

14 87099_1.book Page 4 Tuesday, January 27, :45 PM 4 ST70+ User Reference Manual 3.62 n (92 mm) 0.27 n (7 mm) 1.36 n (34.5 mm) 5.35 n (136 mm) 5.35 n (136 mm) 3.62 n (92 mm) Fgure 1-3: Keypad dmensons 0.88 n (22.5 mm) 1.36 n (34.5 mm) D Power supples In a typcal ST70+ system, dsplays and keypads are powered by 12 V dc from SeaTalk ng. The power loadng from SeaTalk ng s descrbed n terms of a Load Equvalency Number (LEN) for each product. Each dsplay has a LEN value of 1 and each keypad type has a LEN value of 2. When plannng an ST70+ system, take nto account the total LEN of all the products you ntend nstallng, to ensure SeaTalk ng s not overloaded. Refer to the SeaTalk ng Reference manual to ensure correct nstallaton.

15 87099_1.book Page 5 Tuesday, January 27, :45 PM Chapter 1: Gettng started 5 Dedcated dsplay power supply In addton to usng power from SeaTalk ng, the ST70+ dsplays requre an addtonal dedcated 12 V power source. Each ndvdual dsplay must be separately connected to the power source wth the power cable suppled, and each power cable must be connected to the power supply va a 5A fuse or equvalent protectve devce. Postonng ST70+ dsplays & keypads Stng requrements WARNING: Potental gnton sources The equpment n these nstructons s NOT approved for use n hazardous/flammable atmospheres such as an engne room. CAUTION: Mantan structural safety Where t s necessary to cut holes (e.g. for cable routng and dsplay mountng), ensure that these wll not cause a hazard by weakenng crtcal parts of the vessel s structure. ST70+ dsplays and keypads can be ftted ether above or below deck, provded the rear of each product s protected from contact wth water.each product must also be postoned where: It s easly read by the helmsman. Bear n mnd that there are lmtatons n how well the dsplay screens can be read when not vewed straght-on, Note that the maxmum vewng angles are: From above: 30 From below: 60 From the each sde: 55 It s protected aganst physcal damage. It s at least 9n (230mm) from a compass. It s at least 20n (500mm) from rado recevng equpment. There s reasonable rear access for nstallaton and servcng. It s wthn 400 mm of a SeaTalk ng T-pece or connector block, or another ST70+ dsplay or keypad. Other consderatons When plannng an nstallaton, ensure that you poston the dsplays and keypads for most effectve control of the boat, bearng n mnd that, durng the subsequent commssonng procedure: Each ST70+ dsplay s set up to operate ether as an Instrument or as a Plot Controller. The entre ST70+ system can be confgured to operate n groups, wth each group comprsng up to four dsplays all of the same type,.e. all Instruments or all Plot Controllers. At least one keypad s allocated to each group of dsplays. The allocated keypad must be of the approprate type for the dsplay group,.e. ether an Instrument keypad or Plot Controller keypad.

16 Document reference: Date: October _1.book Page 6 Tuesday, January 27, :45 PM 6 ST70+ User Reference Manual 1.3 Equpment & tools Parts suppled ST70+ dsplay Mountng bracket Seal Suncover SeaTalk ng spur cable - 1 metre SeaTalk ng blankng plug Power cable Stud (x 4) Fnger nut (x 4) ST70+ Installaton Gude Warranty booklet User reference gude CD ROM Installaton gude Fgure 1-4: Dsplay and assocated parts suppled D

17 Document reference: Date: October 2008 Welcome to ST70+ Congratulatons on havng chosen Raymarne ST70+. ST70+ Instruments and Plot Controllers gve you easy access to the mportant nformaton you need and fngertp control over your Raymarne autoplot, to make your boatng experence both safe and enjoyable. Contents General Gettng started...card 1 Dsplay control...card 2 Settng dsplay brghtness...card 3 Settng local tme...card 4 Settng screen colors...card 5 Choosng data unts...card 6 Data lst...card 21 Plot Controller Set up Plot Controller dsplay...card 7 Basc autoplot operaton...card 8 Usng AutoTack...Card 9 Usng autoplot Track mode...card 10 Usng autoplot Wnd Vane mode...card 11 Usng autoplot fshng patterns...card 12 Usng autoplot for power steerng...card 13 Instrument Swtchng pages on & off...card 14 Settng page rollover...card 15 Changng the nformaton on a page...card 16 Changng the page layout...card 17 Usng tmers...card 18 Settng alarms...card 19 Alarm events...card 20 Ths Operatng Gude Ths Operatng Gude descrbes how to use ST70+ Instruments and Plot Controllers on a day-to-day bass. If you need more comprehensve nformaton, refer to the ST70+ Instrument User Reference Manual. Before usng your ST70+ products, ensure they have been prepared for use n accordance wth the Commssonng Procedures n the ST70+ Instrument User Reference Manual. Raymarne UK Ltd, Anchorage Park, Portsmouth, Hampshre PO3 5TD, Unted Kngdom Tel: +44 (0) , Fax:+44 (0) Raymarne Inc,21 Manchester Street, Merrmack, New Hampshre 03054, USA Tel: , Fax: Part Number: Date: October _1.book Page 7 Tuesday, January 27, :45 PM Chapter 1: Gettng started 7 OR OR ST70+ Instrument keypad ST70+ Plot Controller (power boat) keypad ST70+ Plot Controller (sal boat) keypad Mountng bracket Seal Suncover SeaTalk ng spur cable - 1 metre SeaTalk ng blankng plug Stud (x 4) Fnger nut (x 4) Op g Gude ST70+ Installaton Gude Warranty booklet User reference gude CD ROM Installaton gude Operatng gude Fgure 1-5: Keypad and assocated parts suppled D

18 87099_1.book Page 8 Tuesday, January 27, :45 PM 8 ST70+ User Reference Manual Parts not suppled You wll need the followng tools: Power drll Jg saw 92 mm (3 9 /16 n) hole cutter 64 mm (2 1 /2 n) hole cutter 8 mm ( 5 /16 n) drll bt 5 mm ( 3 /16 n) drll bt D Optonal cablng and connectors Each ST70+ product s suppled wth one SeaTalk ng spur cable and one backbone blankng plug and should be connected to a SeaTalk ng system as descrbed n the SeaTalk ng System Installaton Gude (suppled wth the SeaTalk ng backbone kt).you may need other SeaTalk ng components to acheve ths. Spur cable Backbone Extender Part numbers A ft 3 n (400 mm) A ft 3 n (1 m) A ft 10 n (3 m) A ft 4 n (5 m) Part Number A06030 Backbone kt Part number A25062 Backbone cable - 16 ft 4 n (5 m), (x 2) 65 ft 7 n (20 m) Backbone termnator, (x 2) T pece, (x 4) Power cable Fgure 1-6: Optonal SeaTalk ng parts D

19 87099_1.book Page 9 Tuesday, January 27, :45 PM Chapter 1: Gettng started 9 For further nformaton on SeaTalk ng products, refer to the SeaTalk ng System Installaton Gude, talk to your dealer, or vst the Raymarne web ste at

20 87099_1.book Page 10 Tuesday, January 27, :45 PM 10 ST70+ User Reference Manual

21 87099_1.book Page 11 Tuesday, January 27, :45 PM Chapter 2: Installaton Before startng to nstall your ST70+ products, read Chapter, Gettng Started, so that: You have all the necessary equpment to hand. You know where you want to nstall the ST70+ products and where the approprate network connecton ponts are. 2.1 Procedure WARNING: Before startng nstallaton, ensure the boat s securely moored and that electrcal supples are swtched off. Wth the boat at docksde, nstall each ST70+ dsplay and keypad by carryng out the procedures for: Cablng. Mountng & connectng Cablng 11 SeaTalk ng T pece SeaTalk ng backbone SeaTalk ng T pece ST70+ dsplay ST70+ dsplay ST70+ keypad SeaTalk ng spur SeaTalk ng spur SeaTalk ng spur Dsplay power cable Fgure 2-1: Typcal cablng at rear of dsplays and keypads Dsplay power cables Dsplay power cable To dsplay power supply va 5A fuse D Ensure you have a sutable power supply for the dsplays (as descrbed n Chapter 1), then run a power cable (suppled) from the ntended locaton of each dsplay, va a 5 A fuse (or equvalent protectve devce) to the dsplay power supply.

22 87099_1.book Page 12 Tuesday, January 27, :45 PM 12 ST70+ User Reference Manual SeaTalk ng connectons For each ST70+ product: 1. Locate a SeaTalk ng connecton pont wthn 400 mm of the ntended locaton of the product. Ths can be at any of the followng: SeaTalk ng T pece. Spare SeaTalk ng connector on a product already nstalled. SeaTalk ng 5-way connector block. 2. For each SeaTalk ng connecton, label both ends of a SeaTalk ng spur cable, then connect t to the connecton pont, and run the free end to the ntended locaton. Mountng & connectng products Mountng optons You can ether flush mount or surface mount your ST70+ dsplays and keypads. Surface mount Flush mount D Fgure 2-2: Example of flush and surface mountng Use the approprate template to facltate the nstallaton of each product. Templates for flush and surface mountng are provded as follows: Keypad templates are ncluded at the end of ths Installaton Gude. Dsplay templates are provded wth each dsplay, on a separate document At each locaton, ensure that: The mountng panel s capable of supportng the product(s) you ntend nstallng. The mountng surface s clean, smooth and flat. There s suffcent space behnd the mountng panel to accommodate the rear of the product and the connectons to t.

23 87099_1.book Page 13 Tuesday, January 27, :45 PM Chapter 2: Installaton 13 Note: Mountng procedure Illustratons showng how to surface mount and flush mount an ST70+ dsplay are gven at Fgure 2-3: and Fgure 2-4: respectvely. Keypads are mounted n a smlar manner except they connect only to SeaTalk ng and do not have an addtonal power cable connecton. To mount an ST70+ dsplay or keypad: 1. Use the approprate flush- or surface-mount template to cut the mountng slot for the dsplay and to drll holes for the fxng screws. 2. Clean and de-burr the mountng surface. 3. Ft gaskets and brackets. Stck the self-adhesve sde of the gasket to the dsplay or keypad, NOT to the mountng locaton. Surface mountng Fgure 2-3: Surface mountng a dsplay D

24 87099_1.book Page 14 Tuesday, January 27, :45 PM 14 ST70+ User Reference Manual Flush mountng Fgure 2-4: Flush mountng a dsplay Connectng Make the necessary connectons to each product (see Fgure 2-5): At each dsplay and keypad make at least one SeaTalk ng connecton. At each dsplay also make a power connecton. D

25 87099_1.book Page 15 Tuesday, January 27, :45 PM Chapter 2: Installaton 15 ng 1. Rotate SeaTalk connector collar to the UNLOCKED poston ng 2. Ensure SeaTalk cable end connector s correctly orented, then fully nsert ng 3. Rotate SeaTalk connector collar clockwse (2 clcks) untl t snaps nto the LOCKED poston 4. Ensure dsplay power cable connector s correctly orented, fully nsert then secure Fgure 2-5: Rear connectons D

26 87099_1.book Page 16 Tuesday, January 27, :45 PM 16 ST70+ User Reference Manual 2.2 Installng transducers Transducer types ST70+ can operate wth: Conventonal transducers (separate Speed, Depth and Wnd). Smart transducers (combned Depth/Speed/Temperature (DST) and combned Depth/Temperature (DT) transducers). The man dfference n nstallaton requrements for these two groups s that each conventonal transducer connects to a dedcated pod whch then connects to SeaTalk ng va a ftted SeaTalk ng spur cable, whereas each smart transducer connects drectly to the SeaTalk ng backbone va a ftted SeaTalk ng spur cable. Fttng Ft each transducer n accordance wth the accompanyng nstructons. Connectng Conventonal transducers CAUTION: Do not use the wrong pod Usng the wrong type of pod could cause damage to your equpment. Before connectng, always ensure that the pod you ntend to use s compatble wth the transducer type. Conventonal transducers and assocated pods are avalable for wnd, depth and speed. Each transducer connects va a dedcated pod to SeaTalk ng. Connect each conventonal transducer as follows: 1. Ensure the pod you ntend usng s compatble wth the transducer,.e. speed pod for a speed transducer, depth pod for a depth transducer or wnd pod for a wnd transducer. SeaTalk ng backbone SeaTalk ng T pece Speed pod Speed transducer 15 metre cable SeaTalk ng spur 400mm cable (ftted to pod) Fgure 2-6: Connectng conventonal transducer D

27 87099_1.book Page 17 Tuesday, January 27, :45 PM Chapter 2: Installaton Referrng to the nstructons suppled wth the pod, connect the transducer to the pod. When dong ths, ensure that each wre s connected to the correspondnglycolored connector. 3. Connect the pod to the SeaTalk ng backbone usng the 400mm SeaTalk ng spur cable suppled wth each pod. Pods must be located no further than 400mm from ther correspondng connecton ponts on the backbone. Smart transducers ST70+ products are compatble wth the followng smart transducer types: Combned depth/speed/temperature transducer, type DST800. Combned depth/temperature transducer, typedt800. Connect the ftted SeaTalk ng spur cable from each smart transducer to a convenent pont on the SeaTalk ng backbone. SeaTalk ng backbone SeaTalk ng T pece SeaTalk ng spur (ftted to transducer) Smart transducer Fgure 2-7: Connectng smart transducer D Commssonng requrement WARNING: Product nstallaton & operaton An ST70+ system must be prepared for use n accordance wth the Commssonng Procedures, before t s used for operatonal purposes. Falure to comply wth ths could result n death, personal njury, damage to your boat and/or poor product performance. After nstallaton, an ST70+ system must be commssoned n accordance wth Chapter 2: Commssonng Procedures, before t s used for operatonal purposes.

28 87099_1.book Page 18 Tuesday, January 27, :45 PM 18 ST70+ User Reference Manual

29 87099_1.book Page 19 Tuesday, January 27, :45 PM 19 Chapter 3: Commssonng Procedures 3.1 Introducton Requrement Note: WARNING: Product nstallaton & operaton An ST70+ system must be prepared for use n accordance wth the Commssonng Procedures, before t s used for operatonal purposes. Falure to comply wth ths could result n death, personal njury, damage to your boat and/or poor product performance. Before an ST70+ system s used for the frst tme, t must be commssoned n accordance wth the nstructons n ths chapter. Commssonng comprses: 1. Intal setup. 2. Docksde setup. 3. Open water calbraton. 4. Checkng autoplot operaton. If your ST70+ product s connected to an exstng SeaTalk ng system that has already been successfully commssoned, you do not need to commsson the system agan. Autoplot calbraton The detaled requrement for autoplot calbraton s determned by the autoplot. The autoplot calbraton procedures n ths chapter are those for a typcal Raymarne autoplot system. If necessary adapt these procedures to sut your system. If you need assstance, please contact your Raymarne dealer. Control nformaton As the ST70+ dsplays do not have ftted controls, all control actons are made at the approprate ST70+ keypad. Informaton on keypad controls, commssonng and menu maps s provded n the ST70+ User Reference Manual whch s n PDF form on the CDROM suppled wth each ST70+ product. If you are unclear about the acton of keypad controls, please refer to the ST70+ User Reference Manual before you start the commssonng procedure. Wherever an nstructon calls for a button to be pressed or a control to be operated, ths refers to the approprate keypad. Commonly used control functons Many ST70+ setup functons and values, plus many dsplay optons are selected by scrollng to the requred functon or value, then confrmng the value. The manner n whch you scroll to a functon or value you want and confrm your selecton, depends on keypad type

30 87099_1.book Page 20 Tuesday, January 27, :45 PM 20 ST70+ User Reference Manual Scrollng. To scroll to an opton or set a value, ether: Press the < and > buttons on the sal boat Plot Controller keypad, or Turn the Rotary Control on the power boat Plot Controller keypad or the Instrument keypad OK functon The manner n whch you confrm, (.e. OK ) selectons and edted values depends on whch keypad type you are usng. On a salboat Plot Controller keypad, press and release the OK button. On a power boat Plot Controller keypad or an Instrument keypad, press and release the center of the Rotary Control. Select Dsplay The Select Dsplay button s used n systems wth more than one dsplay, to select the dsplay you want to control or set up. One press hghlghts the currently selected dsplay. If you press Select Dsplay agan whle the currently selected dsplay s hghlghted (.e. wthn 6 seconds), ths selects the next dsplay n the system. Repeatng ths acton enables you to select each dsplay n turn. 3.2 Intal setup Carry out the ntal setup procedures n the followng sequence: Swtch on. Selectng language. Settng vessel type. Settng dsplay types and groups. Allocate keypad. Set date and tme format (only f GPS s ftted). Set correct local tme (only f GPS s ftted). Set requred data unts. or Scrollng OK functons = Swtch on. At an ST70+ keypad, press the power button swtch on the dsplays. When an ST70+ system s frst swtched on after nstallaton, one dsplay shows a select Language menu. Ths s the actve dsplay. Language Englsh (UK) Other dsplays show a Select Dsplay con. Press OK to select If necessary use the Select Dsplay button on any ST70+ keypad to select another dsplay as the actve dsplay,.e. so t shows the select Language menu. D

31 87099_1.book Page 21 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures 21 Selected dsplay Language Englsh (UK) Press OK to select Selectng language Scroll to select the requred language. D CAUTION: Be sure to select the correct Language. If you select the wrong language, the ST70+ system wll be dffcult to use. If you are sure you have selected the language you want, press OK to confrm the selecton, to dsplay the Welcome screen. When you are ready to proceed, press OK to dsplay the Vessel Type menu. Settng Vessel Type The Vessel Type menu enables you to automatcally apply the optmum system settngs for your vessel type. The optons are: Race Sal Inboard Speed Boat Sal Cruser Power Cruser 1* Catamaran Power Cruser 2* Workboat Power Cruser 3* RIB Sport Fshng Outboard Speed Boat Pro Fshng Vessel Type Inboard Speedboat Selectng vessel type helps us to confgure your system. Press OK to select D *Power Cruser settngs. Note that the Power Cruser settngs apply as follows: Power Cruser 1 - vessels capable of speeds up to 12 knots. Power Cruser 2 - vessels capable of speeds up to 30 knots. Power Cruser 3 - vessels capable of speeds greater than 30 knots.

32 87099_1.book Page 22 Tuesday, January 27, :45 PM 22 ST70+ User Reference Manual Note: Select type Scroll to select the vessel type that most closely corresponds to your vessel. When you have chosen the vessel type, press OK to confrm the choce. The Tme and Date values and the data Unts consdered most approprate for the Language and Vessel Type you chose, are then automatcally appled to your ST70+ system and an automatc check of system parameters s carred out. On completon, a System confguraton page s present all dsplays n the system. Settng dsplay types and groups You must now: Select the dsplay you want to set up. Set the dsplay type for each dsplay (Instrument or Plot Controller). Allocate each dsplay to a group. Set the sequence number of each dsplay wthn the group. Lnk at least one keypad to each group. To do ths: 1. Wth the System confguraton page dsplayed, press OK to dsplay the Confgure ths dsplay page. For unassgned dsplays (e.g. at frst swtch on), the legends Group and Number are dsplayed. If the selected dsplay has already been set up, ths shows the current group and number n the group for the selected dsplay. System confguraton Now confgure each dsplay type, group and order. Then lnk one or more keypads to that group. Press OK to contnue Confgure ths dsplay Press OK to confgure ths dsplay 2. Use the Select Dsplay button as necessary, to move the screen hghlght to the dsplay you want to set up,. e. so t s the selected dsplay. 3. Press OK to dsplay the Dsplay type setup Dsplay type page. 4. Scroll to select ether Instrument or Autoplot, as requred. Autoplot From ths pont, you must use a keypad type approprate to the dsplay type you have selected. Group Number Select each dsplay n turn. Press OK to confgure. When all done, press MENU. Confgure ths dsplay as an nstrument or autoplot controller Press OK to accept D D D

33 87099_1.book Page 23 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures 23 Note: 5. Press OK to confrm the dsplay type and dsplay the Assgn group page. 6. Scroll to the name of the group to whch you want to assgn the dsplay. Plot Controller group name optons are: Plot-1, Plot-2, Plot-3, Plot-4 and Plot-5 Instrument group name optons are: Inst-Helm1, Inst-Helm2, Inst-Cockpt, Inst-Flyb., Inst-Mast, Inst-1, Inst-2, Inst-3, Inst-4, Inst-5, Inst-6, Inst-7, Inst-8, Inst-9, Inst-10, Inst-11, Inst-12, Inst-13, Inst- 14 and Inst Press OK to save the group assgnment and dsplay the Assgn order n group page. Each dsplay n a group has a dscrete number, and these numbers determne the order n whch dsplays are selected wthn the group durng normal operaton, when the Select Dsplay button s used. 8. Scroll to the requred number. 9. Press OK to save the group settngs and dsplay the Lnk keypad to group page. 10. If you have not allocated keypads to the group contanng the dsplay you are settng up:. Press OK at a keypad you want to lnk to ths group.. Wat untl the confrmng popup dsappears.. Repeat and for each keypad you want to lnk to ths group. Remember you can only lnk Instrument keypads to Instrument groups, and Plot Controller keypads to Plot Controller groups. 11. When you have allocated all the requred keypads to ths group, press MENU to save the group settngs and dsplay the Confgure ths dsplay page. 12. Repeat steps 3 to 11 for each dsplay. 13. When all dsplays are set as you want, and wth Assgn group the Confgure ths dsplay page dsplayed, press MENU, to leave the Settng dsplay types and groups procedure, and dsplay ether: A Tme & date summary page, f your system provdes GPS nformaton, or A Unts Summary page f GPS nformaton s not avalable. Plot-2 Assgn nto a group of one or more dsplays. All dsplays must be the same type. Press OK to accept Assgn order n group 2 Assgn the order of ths dsplay wthn the group. Press OK to accept Lnk keypad to group Press OK on each keypad that you want to lnk to ths dsplay group Press MENU to fnsh D D D

34 87099_1.book Page 24 Tuesday, January 27, :45 PM 24 ST70+ User Reference Manual Note: Date & Tme The Tme & Date summary page shows the current values appled to your ST70+ system. Date 14/06/07 If your dsplay s not recevng GPS nformaton, the Tme Tme Offset -1 Hrs & Date page s not dsplayed. In ths case, proceed wth Tme Format 24-hour Date Format dd/mm/yy the Data unts setup procedure below. Check the nformaton, on the Tme & Date summary page, then press OK to dsplay the Tme & Date setup menu. Press OK to contnue You can change certan date and tme parameters. You can: Select ether dd/mm/yy or mm/dd/yy as the date format Select ether 12-hour (am/pm) or 24-hour as the tme format. Set the value of the tme offset to gve the requred local tme. If you want to change any Tme & Date values, carry out the Settng date format, Settng tme format and/or Settng local tme procedure below, as approprate. If you do not want to change any Tme & Date values, proceed from Leavng date & tme setup below. Settng date format To set the requred date format: 1. At the Tme & Date setup menu, scroll to the Set date format opton, then press OK to dsplay the Set date format page. Tme & Date Tme 11:01:03 10 These are your current settngs. Tme & Date 10 Set date format D Press OK to select D Scroll to select the requred Date Format, then press OK to save the format and return to the Tme & Date summary page. 3. Press OK to select the Tme & Date setup menu. Set date format 10 dd/mm/yy Settng tme format To set the requred tme format: 1. Wth the Tme & Date setup menu dsplayed, scroll to select the Tme Format opton, then press OK to dsplay the Set tme format page. Use < & > to adjust. CANCEL exts wthout savng. Tme & Date 10 Press OK to accept Set tme format D Press OK to select D

35 87099_1.book Page 25 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures Scroll to the requred Tme Format, then press OK to save the format and return to the Tme & Date summary page. 3. Press OK to select the Tme & Date setup menu. Set tme format 12-hour Use < & > to adjust. CANCEL exts wthout savng. Press OK to accept D Settng local tme Tme & Date Note: If your ST70+ dsplay s connected to a Raymarne multfuncton dsplay, then the tme offset s controlled by the multfuncton dsplay and you cannot use ths procedure to change t. To set the dsplay tme to your local tme. 1. At the Tme & Date setup menu, use < and > to select the Set tme offset opton, then press OK, to dsplay the Set tme offset page. 2. Scroll to set the correct local tme. For example, f your local tme s 1 hour after GMT, set Press OK, to save the settng and return to the Tme & Date setup menu. Set tme offset Press OK to select Set tme offset -1 hour D Leavng date & tme setup When your date and tme formats and values are set as requred: 1. At the Tme & Date setup menu, scroll to the Contnue opton. 2. Press OK to proceed to the Unts summary page. 3. Proceed from Data unts (below). Data unts The Unts summary comprses two pages and shows unts currently n use. You can accept all or change any of the data unt settngs. You can set: Speed to ether mles per hour, klometers per hour or knots. Dstance to ether mles, nautcal mles or klometers. Depth to ether feet, fathoms or meters. Use < & > to adjust. CANCEL exts wthout savng. Press OK to accept Tme & Date Contnue Press OK to select Unts summary 6 Speed pt Dstance Depth Wnd Speed Headng Flow Rate Temperature 10 These are your current settngs. Press OK to contnue KTS NM FT KTS Mag G/H oc D D D

36 87099_1.book Page 26 Tuesday, January 27, :45 PM 26 ST70+ User Reference Manual Wnd speed to ether knots or meters per second. Headng to ether magnetc or true. Flow rate to ether US gallons per hour, UK gallons per hour or lters per hour Temperature to degrees Celsus or degrees Fahrenhet. Pressure to pound per square nch or klo Pascals. Volume to ether US gallons, UK gallons or lters Number of engnes to ether 1, 2, 3, 4 or 5. Number of batteres to ether 1, 2, 3, 4 or 5. Number of fuel tanks to ether 1, 2, 3, 4 or 5. Press OK to see the second Unts summary page, and f you want to return to the frst page from the second, press CANCEL. Check the nformaton on the Unts summary Select unts pages, then wth the second Unts summary page dsplayed, press OK to dsplay the Select unts menu. If you want to change any data unts, carry out the Changng unts procedure below. If you do not want to change any data unts, proceed from Leavng unts setup below. Changng unts To change any data unts: 1. Wth the Select unts menu dsplayed, scroll to select the type of data you want to change,.e. Speed, Depth, Dstance, Wnd Speed etc. 2. Press OK to dsplay the setup page for the unts you have selected. 3. Scroll to select the requred unts. 4. Press OK to save the unts settng and return to the frst Unts summary page. 5. Press OK twce, to dsplay the Select unts menu. 6. If you want to change any other unts, repeat steps 1 to 5 of ths procedure. Wnd Speed Unts Select unts to change, usng < or >. Press OK to select Wnd Speed Unts KTS Select requred unts, usng < or >. CANCEL exts wthout savng Press OK to accept D D Leavng unts setup: When your data unts are set as requred: 1. Wth the Select unts menu dsplayed, scroll to the Contnue opton. 2. Press OK. Intal setup now ends. Select unts Contnue Select unts to change, usng < or >. Press OK to select D

37 87099_1.book Page 27 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures 27 Intal setup end routne If the functon of any dsplay has changed snce swtch on (.e. Instrument to Plot Controller or vce versa), the relevant dsplays reboot when you press OK at the Select unts menu. When any necessary reboot has taken place, an operatonal page for ether an Instrument or a Plot Controller s dsplayed, dependng on whch dsplay functon you set prevously. The dsplay s now n operatng mode. Next actons Now carry out the remanng docksde setup procedures. 3.3 Docksde setup Carry out the docksde setup procedures n the followng sequence: Autoplot system. Transducer setup. Mscellaneous setup. Autoplot system CAUTION: Before startng any docksde setup procedure, ensure the boat s securely moored alongsde. The autoplot docksde setup procedures comprse: Usng the Docksde wzard to: Set drve type. Perform motor phasng check. Perform rudder check. Settng rudder hard over tme. The exact procedures are dependent on the type of autoplot. Typcal procedures are gven here, but you may need to adapt these procedures to sut your nstallaton. If you requre advce or assstance, please contact your local Raymarne dealer. Docksde wzard Startng the wzard At a convenent Plot Controller: 1. Press MENU to dsplay the Man Menu. 2. Scroll to Autoplot calbraton then press OK to dsplay the Autoplot Autocalbraton menu.

38 87099_1.book Page 28 Tuesday, January 27, :45 PM 28 ST70+ User Reference Manual 3. Scroll to select Commssonng, then press OK to dsplay the Commssonng menu. 4. Scroll to Docksde wzard then press OK to start the wzard. The Docksde Calbraton page s dsplayed. Docksde Calbraton Before you can use your autoplot you need to do some docksde checks. Press CANCEL to ext wthout savng. Note: Set drve type Wth the Docksde calbraton page dsplayed at Press OK to contnue Drve Type the selected Plot Controller, press OK on the assocated keypad to dsplay the Drve type page then: 1. Scroll to select the autoplot drve type approprate to your boat. The optons avalable depend on the type of autoplot, but optons supported are: Type 1 Lnear CANCEL returns to the prevous page. Press OK to select Type 1 Lnear Jet Drve (fly-by-wre) Type 2 Lnear Wheel Drve Type 2 Hydraulc Lnear Tller Hydraulc Pump Type 1 Type 3 Hydraulc Lnear CR Solenod Hydraulc Pump Type 2 I/O Stern Sport Drve Hydraulc Pump Type 3 IPS Rotary Drve Type1 Constant Runnng Pump Jet Drve (pump) Rotary Drve Type 2 Verado If your drve type s not ncluded, seek advce from your Raymarne dealer. 2. Press OK to save your settng and dsplay the next setup page. Ths s ether: The Rudder check (center) page, f the boat has a rudder reference transducer, or The Motor phasng non-referenced page, f a rudder reference transducer s not ftted. 3. Press OK to proceed wth the Rudder and motor checks. Use the procedure for ether Systems wth a Rudder Reference transducer or Systems wthout a Rudder Reference transducer, as approprate. Rudder and motor checks for systems wth a Rudder Reference transducer After settng the drve type, the Rudder check page (center) s dsplayed, f your system has a Rudder Rudder Check Reference transducer. If ths s the case, carry out the rudder and motor checks as follows: 1. Manually center the rudder. D D Center the rudder and press OK. Press CANCEL to ext. Press OK to accept D

39 87099_1.book Page 29 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures Press OK to dsplay the Rudder Check (port) page. 3. Turn the wheel fully to port. Rudder Check 4. Press OK, to dsplay the Rudder Check (starboard) page. 5. Turn the wheel fully to starboard. Turn the wheel hard to PORT and press OK. Press CANCEL to ext. Rudder Check Press OK to accept D Press OK, to dsplay the Rudder Check page (center) agan. Turn the wheel hard to STARBOARD and press OK. Press CANCEL to ext Press OK to accept Rudder Check D Press OK to dsplay the Rudder Check Task Complete page. Center the rudder and press OK. Press CANCEL to ext. Press OK to accept Rudder Check D Press OK to dsplay the Motor Check entry page. Task Complete - success. Press CANCEL to ext. Motor Check Press OK to contnue D IS IT SAFE TO TAKE THE HELM! Press CANCEL to ext Press OK to contnue D

40 87099_1.book Page 30 Tuesday, January 27, :45 PM 30 ST70+ User Reference Manual 9. Press OK to dsplay a Motor Check cauton page. Motor Phasng Non-referenced Please center and let go of rudder and release any rudder drve clutch. Press OK f t s safe for Autoplot to engage the rudder drve. 10. Manually center the rudder, then f t s safe to proceed, press OK. The autoplot automatcally drves the rudder n one drecton. When ths s complete a result page s dsplayed. Press CANCEL to stop Motor Check Rudder drve has been detected. Please press OK f t s safe to engage the rudder drve n the opposte drecton. D Press CANCEL to stop D If t s safe to proceed, press OK. The autoplot then drves the rudder n the opposte drecton. When ths check s complete, a Motor Check Task Complete page s dsplayed. 12. Press OK to end the autoplot docksde wzard. Motor Check Task Complete - success Press CANCEL to stop Rudder and motor checks for systems wthout a rudder reference transducer After settng the drve type, the Motor Phasng Nonreferenced entry page s dsplayed, f your system Motor Phasng Non-referenced does not have a Rudder Reference transducer. D Carry out the rudder and motor checks as follows: 1. Press OK to dsplay a Motor Check cauton page 2. If t s safe to proceed. press OK, then check whch way the autoplot drves the rudder.drecton. IS IT SAFE TO TAKE THE HELM! Press CANCEL to ext Press OK to contnue Motor Phasng Non-referenced Please center and let go of rudder and release any rudder drve clutch. Press OK f t s safe for Autoplot to engage the rudder drve. D Press CANCEL to stop D

41 87099_1.book Page 31 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures When the PORT result page s dsplayed, press ether OK f the rudder moved to port, or CANCEL f the rudder dd not move to port. Motor Phasng Non-referenced 4. If you press OK a second Motor Check cauton page s dsplayed. 5. If t s safe to proceed. press OK, then check whch way the autoplot drves the rudder.drecton. 6. If you press OK a second Motor Check cauton page s dsplayed. 7. When the STBD result page s dsplayed, press ether OK f the rudder moved to starboard, or CANCEL f the rudder dd not move to starboard. 8. If you press OK a task complete page s dsplayed. 9. Press OK to end the autoplot docksde wzard. Dd the rudder move to PORT? Press CANCEL for NO. Press OK for YES Motor Check Please press OK f t s safe to engage the rudder drve n the opposte drecton. Press CANCEL to stop Motor Phasng Non-referenced Dd the rudder move to STBD? Press CANCEL for NO. Press OK for YES Motor Check D D D Note: Hard over tme Task Complete - success Press CANCEL to stop Not applcable to boats wth a rudder reference transducer. On boats wthout a rudder reference transducer, t s of crtcal mportance to set the hard over tme, to ensure accurate autoplot operaton. To do ths: At a convenent Plot Controller: 1. Press MENU to dsplay the Man Menu. 2. Scroll to Autoplot calbraton then press OK to dsplay the Autoplot Autocalbraton menu. 3. Scroll to select the Drve settngs opton then press OK to dsplay the Drve settngs menu. D

42 87099_1.book Page 32 Tuesday, January 27, :45 PM 32 ST70+ User Reference Manual 4. Scroll to select the Hard Over tme opton then press OK to dsplay the Hard Over tme page. 5. Measure the tme t takes for the autoplot to drve the rudder from hard over port, to hard over starboard. 6. On the Hard over tme page, scroll to set the approprate tme n the edt box. 7. Press OK to save the settng and return to the Drve settngs menu. Hard Over Tme 12 The tme to drve between lmts. Press OK to accept D End of autoplot docksde setup At the end of the autoplot docksde setup, use the CANCEL button to return to a Plot Controller operatonal page. Before startng any sea tral or other open water calbraton, carry out the Transducer setup and Mscellaneous setup procedures (below). Transducer setup CAUTION: Before startng any docksde setup procedure, ensure the boat s securely moored alongsde. Use these docksde setup procedures to set: Correct depth offset and sea temperature. Requred method for calculatng ground wnd. Correct magnetc varaton. Requred dsplay response. Trm tab calbraton. Introducton to transducer setup Depth, speed and temperature data are derved from transducers n the boat s hull. Ether of the followng transducer confguratons may be ftted to provde ths data: Conventonal transducers,.e. separate Depth and Speed, wth the water temperature sensor bult nto the Speed transducer Smart transducers (ether combned Depth/Speed/Temperature (DST) or combned Depth/Temperature (DT) transducers). A Wnd transducer may also be ftted, to provde wnd speed and drecton nformaton. Depth offset and sea temperature must be calbrated as part of the Docksde setup, but the exact method for calbratng these parameters depends on whch transducers are ftted: Wth conventonal transducers, the Depth offset and water temperature are calbrated separately. Wth a smart transducer, the depth offset and water temperature setup are part of one contnuous procedure. The speed and wnd functons are calbrated later as part of the Open water calbraton.

43 87099_1.book Page 33 Tuesday, January 27, :45 PM Chapter 3: Commssonng Procedures 33 Depth offsets Depths are measured from the Depth transducer to the sea bed, but you can apply an offset value to the depth data, so that the dsplayed depth readng represents the depth to the sea bed from ether the keel or the water lne. If an offset s not appled, the dsplayed depth readngs are from the transducer to the sea bed. Before attemptng to set a waterlne or keel offset, fnd out the vertcal separaton between the transducer and ether the waterlne or the bottom of the keel on your vessel, as approprate. See Fgure 3-1. Waterlne offset Offset value of 0.0 Keel offset D Fgure 3-1 Depth offsets Accessng transducer setup Use the Select Dsplay button on a sutable Instrument keypad, to select a convenent Instrument to carry out the Instrument system docksde setup procedures. To access the requred transducer: 1. Wth any operatonal Instrument page Advanced Optons dsplayed, press MENU to dsplay the Man Menu. 2. Scroll to Advanced Optons, then press OK 3. At the Advanced Optons menu, scroll to Transducer Setup Transducer Setup. Press OK to select D