Installation Instructions for Tavan Models TAV-XX-XX

Transcription

1 Installation Instructions for Tavan Page 1 of 12 round version square version Instruction page index: Tavan stand-alone installation Tavan joiner installation Tavan L, T or X connector installation Wiring Diagrams

2 Tavan - Tavan stand-alone installation 1 4-3/8" 7/8" 2 ceiling 2.2 hole anchor Page 2 of Tavan measure 4-3/8" canopy detail hub /64" drill bit location marks spacer wood screw Note: Prior to installation all wires must be present in. Junction box must be located within 96 from the power cable on the. Reference page 12 for wiring diagrams. Note: More than one person is recommended for this installation. 1.1 For stand-alone, align one hub to the junction box & measure the distance from hub to the other hub. Then mark this location to the ceiling. Use canopy detail to slighting off center hub. drill 2.1 On the marked location(s), make a hole using a 13/64" drill bit. 2.2 Insert the anchor into the hole and push completely in. 2.3 Insert wood screw through & washer and then tighten to secure into the anchors. 3 Prior to installing to power, coaxial cable must be prepared to go inside crossbar assembly. If this step if skipped coaxial cable metal sleeve will tangle up. 4 metal sleeve wires 1 - while holding the coaxial cable end. 2 - Pull back about an 1-1/2" of the metal sleeve to expose the wires. - + strain relief crossbar assembly backplate power wire thumb nut 3 - Cut off 1-1/2" of the wires. coaxial cable Note: Prior to wiring the desired height must be determined to cut off any un-necessary wire. 4 - Pull forward the metal sleeve and twist to make a firmer single wire. 4.1 While one person is holding the, the other person can slide the coaxial cable end through the clear s, thumb nut, backplate & crossbar assembly. 4.2 Refer to the wiring diagram on page 12 and make all necessary connections.

3 Tavan - Tavan stand-alone installation 5 6 Page 3 of cable stopper 6.2 crossbar 5.1 #8-32 screw backplate Insert the wire nut connections into the & align the crossbar to the holes and secure using the provided two #8-32 screw. 5.2 Slide the backplate up to the crossbar and secure by hand tightening the thumb nut into the crossbar. 6.1 Untangle each and insert into the until the cable stopper. 6.2 Push on the and feed the into the hub until necessary. Release tab to secure in place. For the closest to the coaxial cable slide through the s on the coaxial cable first coaxial cable aircraft cable 7.1 Tighten each into a, one will be on the backplate and other(s) on the ceiling. If not leveled, adjustments can be made by pushing on the. Then either feed more cable into the hub or pull out cable from the hub and release to secure. 8.1 If necessary make any final adjustments to the cables use the s for a cleaner look. 7.2 Cut off any extra from the hub hole.

4 Tavan - Tavan joiner installation Page 4 of 12 straight/joiner connector installation

5 Tavan - Tavan joiner installation 1 w/joiner Page 5 of 12 screw joiner 1.1 Top View w/joiner 1.1 Lay the s on the floor, then slide each housing to each other secure using the provided screws. 2 measure power cable canopy detail measure /8" 7/8" 4-3/8" Note: Prior to installation all wires must be present in. Junction box must be located within 96 from the power cable on the. Reference page 12 for wiring diagrams. Note: More than one person is recommended for this installation. 2.1 A canopy will be needed for every power feed cable. Measure the distance from one hub to the other hub. Then mark this location to the ceiling. Use canopy detail to slighting off center hub.

6 Tavan - Tavan joiner installation 3 ceiling 3.2 hole anchor Prior Page 6 of 12 to installing to power, coaxial cable must be prepared to go inside crossbar assembly. If this step if skipped coaxial cable metal sleeve will tangle up /64" drill bit location marks spacer metal sleeve wires 1 - while holding the coaxial cable end. 2 - Pull back about an 1-1/2" of the metal sleeve to expose the wires. wood screw drill 3 - Cut off 1-1/2" of the wires. 3.1 On the marked location(s), make a hole using a 13/64" drill bit. 3.2 Insert the anchor into the hole and push completely in. 3.3 Insert wood screw through & washer and then tighten to secure into the anchors. 4 - Pull forward the metal sleeve and twist to make a firmer single wire strain relief coaxial cable crossbar assembly backplate power wire 5.1 While one person is holding the, the other person can slide the coaxial cable end through the clear s, thumb nut, backplate & crossbar assembly. 5.1 thumb nut Note: Prior to wiring the desired height must be determined to cut off any un-necessary wire. crossbar #8-32 screw backplate Insert the wire nut connections into the & align the crossbar to the holes and secure using the provided two #8-32 screw. 6.2 Slide the backplate up to the crossbar and secure by hand tightening the thumb nut into the crossbar Refer to the wiring diagram on page 12 and make all necessary connections.

7 Tavan - Tavan joiner installation 7 Page 7 of cable stopper Untangle each and insert into the until the cable stopper. 7.2 Push on the and feed the into the hub until necessary. Release tab to secure in place. For the closest to the coaxial cable slide through the s on the coaxial cable first Tighten each into a, one will be on the backplate and other(s) on the ceiling. If not leveled, adjustments can be made by pushing on the. Then either feed more cable into the hub or pull out cable from the hub and release to secure. 8.2 Cut off any extra from the hub hole. 8.3 If necessary make any final adjustments to the cables use the s for a cleaner look.

8 Tavan - Tavan L, T or X connector installation Page 8 of 12 L-connector T-connector X-connector

9 Tavan - Tavan L, T or X connector installation 1 Page 9 of 12 housing 1 housing connecting hub 1.1 screw housing 3 housing Lay the s on the floor. Then slide each housing into the connecting hub then secure using the provided screws. 2 hub housing 1 measure housing 2 canopy detail X-connector hub 4-3/8" 7/8" housing 3 housing 4 4-3/8" Note: Prior to installation all wires must be present in. Junction box must be located within 96 from the power cable on the. Reference page 12 for wiring diagrams. Note: More than one person is recommended for this installation. 2.1 A canopy will be needed for every power feed cable. Measure the distance from hub to the other hub. Then mark this location to the ceiling. Use canopy detail to slighting off center hub.

10 Tavan - Tavan L, T or X connector installation 3 ceiling 3.2 hole anchor Prior Page 10 of 12 to installing to power, coaxial cable must be prepared to go inside crossbar assembly. If this step if skipped coaxial cable metal sleeve will tangle up. location marks spacer 1 - while holding the coaxial cable end /64" drill bit metal sleeve wires 2 - Pull back about an 1-1/2" of the metal sleeve to expose the wires. wood screw drill 3 - Cut off 1-1/2" of the wires. 3.1 On the marked location(s), make a hole using a 13/64" drill bit. 3.2 Insert the anchor into the hole and push completely in. 3.3 Insert wood screw through & washer and then tighten to secure into the anchors. 4 - Pull forward the metal sleeve and twist to make a firmer single wire strain relief coaxial cable crossbar assembly backplate power wire 5.1 While one person is holding the, the other person can slide the coaxial cable end through the clear s, thumb nut, backplate & crossbar assembly. 5.1 thumb nut Note: Prior to wiring the desired height must be determined to cut off any un-necessary wire. crossbar #8-32 screw backplate Insert the wire nut connections into the & align the crossbar to the holes and secure using the provided two #8-32 screw. 6.2 Slide the backplate up to the crossbar and secure by hand tightening the thumb nut into the crossbar Refer to the wiring diagram on page 12 and make all necessary connections.

11 Tavan - Tavan L, T or X connector installation cable stopper Page 11 of connecting hub 7.1 Untangle each and insert into the until the cable stopper. 7.2 Push on the and feed the into the hub until necessary. Release tab to secure in place. For the aircraft cable closest to the coaxial cable slide through the s on the coaxial cable first Tighten each into a, one will be on the backplate and other(s) on the ceiling. If not leveled, adjustments can be made by pushing on the. Then either feed more cable into the hub or pull out cable from the hub and release to secure. 8.2 Cut off any extra from the hub hole. 8.3 If necessary make any final adjustments to the cables use the s for a cleaner look.

12 Tavan - Tavan L, T or X connector installation Wiring Diagrams A A.1 conduit for power/control conduit for Page 12 of 12 B.1 power supply power supply A.1 Slightly loosen the 2 screws on the, and remove the power supply. B.1 Run two conduit to the j-box, one for power/control & other for the low voltage. Refer to wiring below for all wiring information. Lutron Ecosystem H-series wire power supply wiring eldoled Dali power supply wiring to ecosystem bus to line voltage E1 (per) E2 (per) hot (blk) neutral (wh) ground (gr) driver rd (+V) blk (-V) to LED module driver rd (+V) blk (-V) DALI (-) DALI (+) DALI (-) DALI (+) line (blk) neutral (wh) ground (gr) to LED module to line voltage to dali Lutron Ecosystem 3 wire power supply wiring eldoled 0-10V Dimming power supply wiring 3 way dimming control to line voltage hot (blk) dim hot (org) neutral (wh) ground (gr) driver rd (+V) blk (-V) to LED module driver rd (+V) blk (-V) 0-10V (-) 0-10V (+) line (blk) neutral (wh) ground (gr) to LED module to line voltage to 0-10V