MEDICAL CYLINDER VALVES
|
|
- Paulina Heath
- 5 years ago
- Views:
Transcription
1 MEDICAL CYLINDER VALVES
2
3 3 TABLE OF CONTENTS INTRODUCTION P Ceodeux meditec solutions P Quality first... P The main medical gases P Product range overview P Technology overview P How to select valves P.012 VALVES INTEGRATED WITH PRESSURE REGULATOR P M707 Lifeball P M706/M713 LIFE+ P M741 LIFE-s P M800 Emergency Back Pack P Protective Guard P.021 CYLINDER VALVE WITH RESIDUAL PRESSURE VALVE P M510/M515/M501/M506/M520/M525 Standard RPV Cylinder Valve P M540/M545/M530/M535 Standard RPV off line P M511/M516/M508/M521/M526 Standard RPV in line P M978/M979/C878 Standard RPV in line P M100/M105/M040/M045/M200/M205 Standard cylinder valve P.026 STANDARD CYLINDER VALVE P M972/M973/M974/M975 standard cylinder valve small cone P D113 Packed Valve P D413 Tied Diaphragm P.029 SPECIAL NITRIC OXIDE CYLINDER VALVE P M966 Pin index Cylinder Valve P M650 Pin index RPV Cylinder Valve P ISO QUALITY ASSURANCE All Rotarex regulators are produced in Europe in accordance with international standards (ISO; CGA...) and are guaranteed to provide safe and reliable performance in operation. All locations are ISO
4 4 INTRODUCTION CEODEUX MEDITEC SOLUTIONS Patient therapy and safety is our main focus in the design, installation, commissioning and operation of medical gas pipeline systems QUANTITY OF SUPPLY Valves are designed in such a way sufficient medical gas capacity can be ensured in order to provide the required flows of gases for the intended number of patients to be treated at any time. IDENTITY OF SUPPLY All our products are designed, produced and controlled for a specific medical gas. All points to which the user or technical staff can connect are gas specified. There is no risk of misconnection. QUALITY OF SUPPLY Our valves maintain quality of supplied medical gases thanks to appropriate selection of material, components cleanliness and internal filtration equipment. Products designs ensure safe supply by minimizing ignition risks, by avoiding patient poisoning risks and by guaranteeing very good performances for accurate therapies. QUALITY FIRST... CEODEUX MEDITEC products are designed, validated, produced and controlled during their whole lifetime according to a very stringent quality system which exceeds requirements of ISO standard. DESIGN All our products comply with local and international standards. Some reference standards: ISO / CGA E-18 ISO / CGA V1 ISO ISO VIPR Standard Cylinder Valves RPV Valves Protection Guard Product design is done through a risk assessment process and is combining proven technologies and innovation to reach the best performance levels. VALIDATION Product validation process guarantees that products are developed and produced to withstand the complete lifecycle (installation, commissioning, normal service and maintenance) PRODUCTION All products are produced in a controlled environment in order to maintain cleanliness An individual traceability is ensured with individual serial number Products are individually controlled and data are recorded for a perfect product management. All products are cleaned according to ISO 15001
5 INTRODUCTION 5 THE MAIN MEDICAL GASES Symbol Name Application Source Type O 2 Air N 2 O CO 2 Air N 2 Oxygen Air Nitrous Oxide Carbon Dioxide Surgical Air Nitrogen Oxygen is one of the most extensively used gases for respiratory therapy and life-support and is additionally used in anesthetic procedures. Medical air is mainly used in respiratory therapy as a power source for patient ventilators, and for blending with oxygen. It is also used as the driving gas for nebulized drugs and chemotherapy agents. Nitrous oxide is used for anesthetic and analgesic purposes, being mixed with air, oxygen, and nebulized agents. Carbon dioxide is used less commonly now as a respiratory stimulant, and for insufflation during surgery. Surgical air (of medical air quality) is also used, at a higher pressure, to power a variety of surgical tools and other devices such as tourniquets. As an alternative, nitrogen can be used for the same purpose as surgical air. - Compressed gas cylinder - Liquid tank - Concentrator - Compressor - Compressed gas cylinder - Liquefied gas cylinder - Liquefied gas cylinder - Compressor - Compressed gas cylinder - Compressed gas cylinder
6 6 INTRODUCTION PRODUCT RANGE OVERVIEW VIPR LIFEBALL P. 14 LIFE + P. 16 LIFE-s P. 18 Gas type O 2 O 2 O 2 Material Chrome plated brass Chrome plated brass Chrome plated brass Inlet pressure 200 bar/300 bar 2000 psi/3000 psi M706: 200 bar/2900 psi M709: 300 bar/4350 psi 200 bar/2900 psi M800 EMERGENCY OXYGEN BACK PACK P. 20 M706/M713 PROTECTIVE GUARD P. 21 Gas type O 2 Ø Material Chrome plated brass Plastic PA6.6 Inlet pressure 200 bar/2900 psi Ø STANDARD CYLINDER VALVE WITH RESIDUAL PRESSURE VALVE OFF LINE M510/M515 P. 22 M501/M506 P. 22 M520/M525 P. 22 M540/M545 P.23 M530/M535 P. 23 Gas type O 2 CO 2 Various gases O 2 Various gases Material Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Inlet pressure 200 bar/2900 psi 200 bar/2900 psi 200 bar/2900 psi 300 bar/4350 psi 300 bar/4350 psi STANDARD CYLINDER VALVE WITH RESIDUAL PRESSURE VALVE IN LINE M511/M516 P. 24 M508 P. 24 M521/M526 P. 24 M978/M979 P. 25 SMALL CONE C878 P. 25 INTEGRATED GAUGE Gas type O 2 CO 2 Various gases O 2, various gases o Material Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Inlet pressure 200 bar/2900 psi 200 bar/2900 psi 200 bar/2900 psi 200 bar/2900 psi 200 bar/2900 psi
7 INTRODUCTION 7 PRODUCT RANGE OVERVIEW STANDARD CYLINDER VALVE M100/M105 P. 26 C040/C045 P. 26 M200/M205 P. 26 M972/M973 P. 27 SMALL CONE M974/M975 P. 27 SMALL CONE Gas type O 2 CO 2 Various gases O 2 Various gases Material Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Chrome plated brass Inlet pressure 200 bar / 2900 psi 200 bar / 2900 psi 200 bar / 2900 psi 200 bar/2900 psi 200 bar/2900 psi SPECIAL NITRIC OXIDE MIXTURES CYLINDER VALVE D113 PACKED VALVE P. 28 D413 TIED DIAPHRAGM P. 29 Gas type No No Material Stainless steel Stainless steel Inlet pressure 200 bar/2900 psi 200 bar/2900 psi PIN INDEX VALVE M966 PIN INDEX CYLINDER VALVE P. 30 M650 P. 31 PIN INDEX RPV CYLINDER VALVE Gas type O 2 O 2 Material Chrome plated brass Chrome plated or natural brass Inlet pressure 232 bar/3364 psi 232 bar/3364 psi
8 8 INTRODUCTION TECHNOLOGY OVERVIEW Ceodeux Meditec uses 4 main technologies to achieve a proper and reliable gas use from the cylinder: VIPR - Valve with integrated pressure regulator Design to save your time: Easy and Ready to use medical valve with in-built regulator, flow meter, contains gauge and outlet pressure connector. - Compact and lightweight : ideal for small cylinder - Fully protected by an ergonomic plastic guard - Filtration system ensures safety against ignition. - Flow meter with orifice plate precision design increase high flow precision and low flow precision for pediatric patients PRODUCT FINDER CEODEUX MEDITEC VIPR M707 P. 014 M706 P. 016 M713 P. 016 M741 P. 018 M800 P. 020 RESIDUAL PRESSURE VALVE - Open/close fonctionnalities - Improved safety thanks to RPV technology included (avoid all contamination risks) - Safe, long, trouble free life under all service conditions - Exist in offset and inline version PRODUCT FINDER CEODEUX MEDITEC RPV valve M510/M515/M501/M506/M520/M525/M540/M545 M530/M535/ M511/M516/M508/M521/M526 P. 024 M978/M979/C878 P. 025 STANDARD CYLINDER VALVE - Standard open/close fonctionnalities - High life cycle thanks to smart choice of materials - Safe, long, trouble free life under all service conditions PRODUCT FINDER CEODEUX MEDITEC Standard valve M100/M105/M040/M045/M200/M205/ M972/M973/M974/M975 P. 026 D113 P. 028 D413 P. 029 PIN INDEX VALVE - Standard open/close fonctionnalities - Yoke outlet connection (PIN INDEX System) - Key operated or handwheel manipulation - High life cycle thanks to smart choice of materials - Safe, long, trouble free life under all service conditions PRODUCT FINDER CEODEUX MEDITEC Pin Index valve M966 P. 030 M650 P. 031
9 INTRODUCTION 9 TECHNOLOGY OVERVIEW DETAILED FUNCTIONNALITIES OF OUR INTEGRATED VALVES VALVE INLET - Anti dust tube according to the last amendment of EN ISO Better protection of the valve against contamination and eliminates the risk of ignition in case accumulation of particles in a filter - Excess flow device Additional safety to avoid excess flow risks and optimize normal flow in use FILLING PORT - Approved for 300 bar (tested at 360 bar) - Active and non-active - Spring in Copper Beryllium material highly compatible with oxidizing gases - O-rings in EPDM - High leak integrity due to seat O-ring and 2-parts design, including degasing hole - High performance of the filling port against ignition with protruding pin design - Filling port fully integrated in the valve body - Endurance performance is twice the requirment of the ISO standard (2000 cycles) PRESSURE GAUGE - NEW Electronic system available (please refer to page 9 for further informations) - Design fully in accordance with the EN ISO including a flow restrictor to prevent part ejection in case of failure - Direct drive technology used for the Bourdon tube to reduce consequences of vibration or shocks - Gauge display tight to water contamination - Safety Relief valve with 3 holes on the glass and tightness evidence sticker - Active pressure gauge for permanent content visibility OUTLET PRESSURE: MEDICAL CONNECTOR - Same outlet as wall outlet used in hospitals with design according national standard - Make connection to medical equipment possible to transport patients - Minimum outlet pressure guaranteed when high flow is required by downstream equipment SHUT-OFF VALVE cycles according CGA V9 (under 360 Bar) - None rotating lower spindle to avoid particles generation - Very low torque design to operate the shut-off valve up to 300 bar - ISO 10297
10 10 INTRODUCTION TECHNOLOGY OVERVIEW DETAILED FUNCTIONNALITIES OF OUR INTEGRATED VALVES REGULATOR SAFETY RELIEF DEVICE - Integrated into the regulator design Quicker reaction - Large contact surface to increase sensitivity and reactivity to overpressure - No risk to damage the device - High flow through the device due to the large diameter and large venting holes FLOWMETER AND HOSEBARB - 12 positions - Continuous flow even in between setting positions during handwheel operation - No possible positioning of the handwheel in-between settings - High precision of the flows - 10 year life time without maintenance - Easy replacement of the handwheel - High leak integrity performance - Flow range: Pediatric applications 0 -> 2 LpmHomecare 0 -> 6 LpmHospital 0 -> 15/ 0 -> 25 Lpm Possibility to be customed PRESSURE REGULATOR - Piston-type regulator - Improved safety and reliability - Direct acting valve (decrease pressure curve) according to ISO and CGA-18 - High compatible materials with Oxygen and Medical applications RESIDUAL PRESSURE VALVE - Protection of the cylinder against external contamination - High endurance performance in terms of leak integrity and functionality According standard ISO cycles Specific seat design to protect sealing O-ring during operation - 3 bar residual pressure guaranteed at maximum flow setting
11 INTRODUCTION 11 TECHNOLOGY OVERVIEW CEODEUX MEDITEC INTELLIGENT ELECTRONIC SYSTEM CHANGE THE WAY YOU USE GAS GROUNDBREAKING INNOVATION TO PERFECTLY REACH OXYGEN THERAPY REQUIREMENTS: Reactivity : Quick and accurate calculation of remaining time Safety : Perfectly suitable for high pressure pure Oxygen environnement Patient & Medical staff Services : Improved cylinders fleet management. - Quicker operations in emergency situations - Bluetooth for wireless communication Optimization : Longer cylinder use thanks to accurate cylinder content management NEW CONTROL GAS USE THANKS TO INFORMATION TRANSPARENCY Get in touch with excellence CYLINDER CONTENT BAR GRAPH (%) Cylinder content* bar graph (%). Visual indications of real quantity of gas into cylinder whatever pressure and temperature parameters are. 2 COLOR CODED CYLINDER CONTENT LEVEL INDICATIONS Red: Warning area : < 10% cylinder content Yellow : Pre-Warning area : 10% < cylinder content < 30% Green : Confortable area : >30% cylinder content 3 PRECISE CYLINDER PRESSURE Precise cylinder pressure Cylinder pressure measurement at real conditions Bar Psi - kpa units available. 1 4 REMAINING TIME FOR USE AT SELECTED FLOW RATE Remaining time for use at selected flow. Accurate and quick calculation of the remaining time according to flow selection and cylinder content. Precise displayed unit: hh:mm 5 CALCULATION SYMBOL FLOW At changing conditions calculation process before displaying remaining time. 6 AVAILABLE WIRELESS BLUETOOTH COMMUNICATION * Quantity of gas into the cylinder NEW GAS THERAPY OPTIMIZATION THANKS TO ANTICIPATION Intelligent and complete alarm system to clearly indicate when user face a critical situation. Audible and visible alerts for enhanced patient safety SYSTEMS FAILURES NORMAL USE ALARMS Indicate when gas flow is critical (Less of 10 minutes of use or 10 bar remaining in the cylinder) Indicate when battery level of the system doesn t guarantee anymore the accurate functionning of the valve Indicate when a sensor default was detected into the system Indicate when an electronic failure was detectead into the system Indicate when environment is not conformed with valve functioning (e.g. high or low temperature)
12 12 INTRODUCTION HOW TO SELECT VALVES BODY MATERIALS Most Ceodeux Meditec valves are available in brass or chrome plated brass. Chrome plated or Raw brass: The most commonly used material for high velocity oxygen applications due to its cost effectiveness, good strength, resistence and low-friction flow properties. Gas Compatibility: make sure the body material is compatible with the gas type you will be using. Need more information? One of our material engineers would be happy to discuss the pros and cons of each option to help you choose the best solution. INLET PRESSURE Different models are designed for different inlet pressure to fit with your applications need (working pressure). For high pressure (200bar/3000psi) the Ceodeux Meditec valves range covers any requirements. The available options are clearly indicated on each product page. Please specify required inlet pressures when ordering. We can also accommodate special requests. OUTLET PRESSURE Especially for VIPR: different models are designed for different outlet pressure to fit with your applications need (working pressure). For low pressure needed in use (4,5bar/50psi) and for accurate flow (from 0-2 to 0-25 Lpm) the Ceodeux Meditec VIPR range covers any requirements. The available options are clearly indicated on each product page. Please specify required inlet pressures when ordering. We can also accommodate special requests. INLET CONNECTIONS Specific cylinder valve connections are required for each gas type. The most common connection types are ¾ -16 UNF and 25E.Other standards and dimensions are available on request. OUTLET CONNECTIONS VIPR: Specific outlet connections are available (medical connector types). According to your national standards the Ceodeux Meditec valves range covers any requirements. Valves: According to your national standards and according to upstream device to be connected (pressure regulator, flex hose,...) the Ceodeux Meditec valves range covers any requirements. Specific flow outlet connections are available (hose barb) according to EN and supplied from flow selector.
13 INTRODUCTION 13 HOW TO SELECT VALVES To choose the right valve for your application and get the best results, you should identify the following technical parameters: TECHNICAL PARAMETER Working pressure Outlet pressure (only for VIPR) Gas type or medical mixture Material: raw brass or chrome plated Inlet connection: 17E, 25E, UNF Outlet connection valve- according to standards Filling port (only for VIPR): acc ISO 5145 or CGA V1.,... Residual pressure: if requested or no Gauge: if specific request Temperature range: -20 C/+65 C or specific Description of the final application: hospital homecare, emergency, or other Guard: select a model and confirm type of cylinder and cylinder weight Guard color: white or green / Other colors on request + marking Bed hanger (only for VIPR): if required or not Environment: if special Product applicable standards: EN ISO (VIPR) EN ISO 10297, CGA E-18 Certification / Approval / Registration CE marked - 93/42/EEC European Medical Device Directive, FDA 510(k) USA, TGA (Therapeutic Goods Administration) - Australia, Health Canada Singapore, ANVISA Brasil Each product page is designed to provide you the essential technical information at a glance: 8 CYLINDER VALVES INTEGRATED WITH PRESSURE REGULATOR CYLINDER VALVES INTEGRATED WITH PRESSURE REGULATOR 9 M706 ALPINOX INTEGRATED VALVE SPECIFICATIONS - Medical integrated valve for Oxygen and others medical gases - For all hospital and homecare applications - Complies with the most stringent standards and requirements - Approved by the major medical authorities worldwide - Available in many different configurations ALL FUNCTIONS IN ONE DEVICE - Active Pressure Measurement - High Pressure Shut Off Valve - Filling Port with Check Valve - Residual Pressure Valve - Pressure Regulator - Safety Relief Device - Flow Selector - Medical Outlet Connection (Optional) REGULATORY - Medical CE certified according to MDD 93/42/EEC amended 2007/47/EC - π certified according TPED Directive 2010/35/EU - Product complies with EN ISO and CGA E-18 Inlet Connection 17E / 25E / M18 / ¼ - 16 UNF Filling Port Flow Outlet Pressure Outlet OPTIONS ISO 5145 / CGA V1 with check valve Hose Barb Acc. to national standards Inlet pressure Temperature range Outlet pressure Flow range 12 pos. 200 bar / 2900 psi -20 C to +60 C 4.5 bar (EU) 3.5 bar (USA) 0-6 Lpm / 0-15 Lpm / 0-25 Lpm Protection Guard CSN / MIF / CBNE with bed hanger Inlet Device Filter / Anti-dust tube / Excess Flow device Body Chrome plated brass Seats PA 6.6 O-ring EPDM Filters Sintered Bronze 20 μm M706 M706 with plastic guard KEY ADVANTAGES Simple Use - Ready-to-use Design - Simple, quick and intuitive function to deliver gas - Easy access to all functions High Performances - Proven and Reliable Single stage piston regulator - High Pressure and Flow Stability and Accuracy outstanding flow outlet pressure stability. Exceptionally accurate. - Wide flow ranges for many applications Safety First - No high pressure manipulation - Shut off valve to isolate high pressure if required - Preset integrated pressure relief device - Flow selector design reducing likelihood of being set between two settings - Continuous flow between settings - Active pressure gauge for a permanent indication - RPV function in order to avoid any potential contamination - Choice of material ensures patient health and safety Others versions and possibilities available upon request PRODUCT REFERENCES Gas Working pressure Inlet Connection Filling port Outlet Pressure Flow Range Medical connector O bar 25E ISO bar 0-25 Lpm DIN M M O bar 25E ISO bar 0-25 Lpm NFS M O psi ¼ - 16 UNF CGA psi 0-25 Lpm DISS 1240 M O bar 17E ISO bar 0-15 Lpm None M N 2 O / O bar 25E ISO bar 0-15 Lpm NFS
14 14 VIPR M707 LIFEBALL - Ultra compact medical integrated valve for O 2 and other medical gases - For all hospital and homecare applications - Centralized control unit on top of the value - High legibility of flow settings with large and phosphorescent chraracters - Very compact and light design - High presicion thanks to compensated regulator - Unique intellingent electronic system to display and manage yuour gas use (for more info please refer to page 9) ALL FUNCTIONS IN ONE DEVICE - Active Pressure Measurement - Filling Port with Check Valve - Residual Pressure Valve - Pressure Regulator - Safety Relief Device - Flow Selector - Medical Outlet Connection (Optional) REGULATORY - Medical CE certified according to MDD 93/42/EEC amended 2007/47/EC - π certified according TPED Directive 2010/35/EU - Product complies with EN ISO and CGA E-18 Standard manometer available
15 VIPR 15 SPECIFICATIONS Inlet Connection Filling Port 25E/17E/¾ -16UNF CGA 540/CGA 577/ISO W24x2/ ISO W30x2/W22x14R Flow Outlet Hose Barb acc. to Iso Pressure Outlet Acc. to national standards Inlet pressure Temperature range Outlet pressure Flow range 12 pos. 200 bar/2000 psi 300 bar/3000 psi -20 C to +60 C 3.5 bar/43 psi 4.5 bar/58 psi 0-2 Lpm / 0-6 Lpm / 0-15 Lpm Body Chrome plated brass Seats PA 6.6 O-ring EPDM Filters Sintered Bronze 60 μm MAIN FUNCTIONNALITIES To better understand roles and benefits of each of these functions please refer to our technological review section on page 9 1 VALVE INLET 2 ANTIDUST TUBE 3 FILLING PORT 4 GAUGE RPV 6 HOSE BARB 7 FLOWMETER 9 8 REGULATOR & SAFETY RELIEF DEVICE 9 BED HANGER OUTLET PRESSURE: MEDICAL CONNECTOR PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Filling Port HP Safety Outlet Pressure Flow Range Pressure outlet Flow outlet Inlet options Guard Color Bed Hanger M707 O 2 A 200 ISO N N HB6 EFD W BH O 2 O 2 17E A 200bar 200 ISO ISO None N 3.5bar Lpm 2 None N Hose Barb HB6 Excess flow EFD White W Yes BH 5145 Ø6mm device Air AIR 25E B 300bar 300 CGA CGA CGA CGA 4.5bar Lpm 6 AFNOR NF Anti dust ADT Green G N 2 O/O 2 N2O 3/4"- 16 UNF V1 S1.1 CCS 2000Psi 2000 UNI UNI JIS JIS 0-15Lpm 15 DIN DIN 3000Psi 3000 JIS JIS 0-25Lpm 25 BS BS w14,5mpa 14.5 SS SS tube JIS AS DISS JIS AS DISS
16 16 VIPR M706/M713 LIFE+ - Medical integrated valve for Oxygen and others medical gases - For all hospital and homecare applications - Complies with the most stringent standards and requirements - Approved by the major medical authorities worldwide - Available in many different configurations ALL FUNCTIONS IN ONE DEVICE - Active Pressure Measurement - High Pressure Shut Off Valve - Filling Port with Check Valve - Residual Pressure Valve - Pressure Regulator - Safety Relief Device - Flow Selector - Medical Outlet Connection (Optional) REGULATORY - Medical CE certified according to MDD 93/42/EEC amended 2007/47/EC - π certified according TPED Directive 2010/35/EU - Product complies with EN ISO and CGA E-18 Other combination available + Medical Outlet Connector Shut Off Valve Filling Port Flow Outlet + Pressure Gauge Config. 1 Filling Port Shut Off Valve Config. 2 Medical Outlet Connector Flow Outlet + Pressure Gauge
17 VIPR 17 SPECIFICATIONS Inlet Connection 17E / 25E / M18 / ¾ - 16 UNF Filling Port Flow Outlet Pressure Outlet OPTIONS Protection Guard ISO 5145 / CGA V1 with check valve Hose Barb MAIN FUNCTIONNALITIES Acc. to national standards CSN2 (see main picture) / MIF (see on page 19) with bed hanger Inlet pressure Temperature range Outlet pressure Flow range 12 pos. Inlet Device M706:200 bar / 2900 psi M709:300bar -20 C to +60 C 4.5 bar (EU) 3.5 bar (USA) 0-6 Lpm / 0-15 Lpm / 0-25 Lpm Filter / Anti-dust tube / Excess Flow device Body Chrome plated brass Seats PA 6.6 O-ring EPDM Filters Sintered Bronze 20 μm To better understand roles and benefits of each of these functions please refer to our technological review section on page 9 1 VALVE INLET ANTIDUST TUBE 3 FILLING PORT GAUGE 5 RPV 6 HOSE BARB 7 FLOWMETER 8 REGULATOR & SAFETY RELIEF DEVICE 1 2 Config 1 9 SHUT OFF VALVE 10 OUTLET PRESSURE: MEDICAL CONNECTOR PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Filling Port HP Safety Outlet Pressure Flow Range Pressure outlet Flow outlet Inlet options Guard type Guard Color M706/M713 O 2 A 200 ISO N N HB6 EFD CSN W O 2 O 2 17E A 200bar 200 ISO ISO None N 3.5bar Lpm 2 None N 5145 Hose Barb HB6 Excess flow Ø6mm device Air AIR 25E B 300bar 300 CGA CGA CGA CGA 4.5bar Lpm 6 AFNOR NF Anti dust N 2 O/ N2O 3/4"- O 2 16 UNF V1 S1.1 CCS 2000Psi 2000 UNI UNI JIS JIS 0-15Lpm 15 DIN DIN 3000Psi 3000 JIS JIS 0-25Lpm 25 BS BS tube Configuration EFD CSN CSN White W Config 1 ADT MIF MIF Green G Config 2 w14, 5MPa 14.5 SS SS JIS JIS AS DISS AS DISS
18 18 VIPR M741 LIFE-s - Compact Medical Integrated Valve for Oxygen and others medical gases - For all hospital and homecare applications - For situations where performance, compactness and light weight are required - Available in many different configurations - Provided with a plastic integrated hanger to carry and protect the valve ALL FUNCTIONS IN ONE DEVICE - Active Pressure Measurement - Cylinder Safety Device - Filling Port with Check Valve - Pressure Regulator - Safety Relief Device - Flow Selector - Medical Outlet Connection (Optional) REGULATORY - Product complies with CGA E-18
19 VIPR 19 SPECIFICATIONS Inlet Connection Filling Port Flow Outlet ¾ - 16 UNF CGA 540 with check valve Hose Barb Inlet pressure Temperature range Outlet pressure 134 bar 2000 psi / bar -20 C to +65 C 3.5 bar/50 psi Body Chrome plated brass Seats PA 6.6 O-ring EPDM Pressure Outlet DISS /16-18UNF Flow range 12 pos. 0-6 Lpm / 0-15 Lpm / 0-25 Lpm Filters Sintered Bronze OPTIONS Inlet Device Filter / Anti-dust tube / Excess Flow device MAIN FUNCTIONNALITIES To better understand roles and benefits of each of these functions please refer to our technological review section on page 9 1 VALVE INLET 2 FILLING PORT 5 3 GAUGE HOSE BARB 5 FLOWMETER 6 REGULATOR & SAFETY RELIEF DEVICE OUTLET PRESSURE: MEDICAL CONNECTOR 1 PRODUCT CONFIGURATOR Gas Inlet Working Connection Pressure Filling Port HP Safety Outlet Pressure Flow Range Pressure outlet Flow outlet Inlet options Guard Color M741 O 2 A 200 ISO N N HB6 EFD O 2 O 2 17E A 200bar 200 ISO 5145 ISO None N 3.5bar Lpm 2 None N Hose Barb HB6 Excess flow EFD White W Ø6mm device Air AIR 25E B 300bar 300 CGA V1 CGA CGA CGA 4.5bar Lpm 6 AFNOR NF Anti dust ADT Green G N 2 O/O 2 N2O 3/4"- 16 UNF S1.1 CCS 2000Psi 2000 UNI UNI JIS JIS 0-15Lpm 15 DIN DIN 3000Psi 3000 JIS JIS 0-25Lpm 25 BS BS w14,5mpa 14.5 SS SS tube JIS AS DISS JIS AS DISS
20 20 VIPR M800 EMERGENCY BACK PACK - A complete safe contained medical oxygen breathing kit for mobile oxygen therapy KIT CONTENTS - 1 back pack: made of polyester PVC reinforecement and inner foam construction Large storage for additional items Shoulder straps for hand-free intervention - 1 cylinder made of aluminium alloy 2L oxygen at 200 bar - 1 integrated valve complies with EN ISO Lpm flow range Residual pressure device Pressure gauge bar Pressure-relief valve Excess flow device - 2 Nasal cannulas Made of lightweight flexible plastic tubing Adult and children sizes KEY FEATURES - The bag is reinforced, waterproof and secures a 2 liters oxygen cylinder equipped with an integrated valve and 2 sizes of nasal cannulas. SPECIFICATIONS Gas Medical Oxygen Flow range 0-15 Lpm Total weight 5,8 Kg Cylinder content Cylinder Pressure 2L 200 bar/2900 psi Gas Autonomy 26 min (at 15 Lpm) CE marking π / CE0029
21 VIPR 21 M706/M713 PROTECTIVE GUARD - Guards and Caps to protect the valve during service and transportation while giving the product an easy access and a good looking design - Designed to protect all products depending on customers specific requirements ALL FUNCTIONS IN ONE DEVICE - Available with an optional bed hanger for an easier handling and support REGULATORY - Designed and tested according to EN ISO standard MIF CSN 2 SPECIFICATIONS Connection On valve body / thread W80 x 1/11 Material PA 6.6 Dimensions Ø143 mm max. Permitted mass Up to 60 Kg Temperature range -20 C to +65 C Colors White / Black / Blue / Green OPTIONS Bed Hanger Assembled on the guard or cap (nif) Label Customized labeling and/or marking
22 22 RPV VALVE M510/M515/M501/M506/M520/M525 STANDARD RPV OFF LINE - High pressure brass cylinder valve for medical gases, O-ring seal type with residual pressure Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Safe, long, trouble free life under all service conditions - Designed and tested according EN ISO and EN ISO OPTIONS - Inlets: 17 E 25 E M 18 US threads - Filter - Burst disc safety device - Thread for dip tube connection - Chrome plating Ref catalog: MPR-EN-1115 SPECIFICATIONS PRODUCT SERIE FEATURES GAS SAFETY O 2 CO 2 VARIOUS GASES WITH WITHOUT M510 M515 M501 M506 M520 M525 Working pressure 200 bar/ 2900 psi Seat orifice size 4 mm O-ring material EPDM Temperature range Helium leak rate at pmax -25 C to +70 C 10-3 mbar l/sec Handwheel material Seat material aluminium polyamid Body material Chrome plated brass PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 ISO 5145 ISO None N N 2 O N 2O 25E B 300bar 300 CGA V1 CGA CGA S1.1 CGA Various gases (*) VG * ¾"-16 UNF CCS 2000Psi 2000 UNI UNI JIS JIS CO 2 CO 2 ¾" NGT OBS 3000Psi 3000 DIN DIN Eu CO 2 /N 2 O EU AFNOR BS SS AS AFNOR BS SS AS * gas or mixture must be confirmed
23 RPV VALVE 23 M540/M545/M530/M535 STANDARD RPV OFF LINE - High pressure brass cylinder valve for medical gases, O-ring seal type with residual pressure Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Safe, long, trouble free life under all service conditions - Designed and tested according EN ISO and EN ISO OPTIONS - Inlets: 17 E 25 E M 18 US threads - Filter - Burst disc safety device - Thread for dip tube connection - Chrome plating Ref catalog: MPR-EN-1115 PRODUCT SERIE FEATURES GAS SAFETY O 2 VARIOUS GASES WITH WITHOUT M540 M545 M530 M535 SPECIFICATIONS Working pressure 300 bar/ 4350 psi Seat orifice size 4 mm O-ring material EPDM Temperature range Helium leak rate at pmax -25 C to +70 C 10-3 mbar l/sec handwheel material Seat material aluminium polyamid Body material Chrome plated brass PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 300bar 3000 ISO 5145 ISO None N N 2 O N 2O 25E B CGA V1 CGA CGA S1.1 CGA Various gases (*) VG * ¾"-16 UNF CCS UNI UNI JIS JIS ¾" NGT OBS DIN DIN Eu CO 2 /N 2 O EU AFNOR BS SS AS AFNOR BS SS AS * gas or mixture must be confirmed
24 24 RPV VALVE M511/M516/M508/M521/M526 STANDARD RPV IN LINE - High pressure brass cylinder valve for medical gases, O-ring seal type with residual pressure Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Safe, long, trouble free life under all service conditions - Designed and tested according EN ISO and EN ISO OPTIONS - Inlets: 17 E 25 E M 18 US threads - Filter - Burst disc safety device - Thread for dip tube connection - Chrome plating Ref catalog: MPR-EN-1115 PRODUCT SERIE FEATURES GAS SAFETY O 2 CO 2 VARIOUS GASES WITH WITHOUT M511 M516 M508 M521 M526 SPECIFICATIONS Working pressure 200 bar/ 2900 psi Seat orifice size 4 mm O-ring material EPDM Temperature range -25 C to +70 C handwheel material aluminium Helium leak rate at pmax 10-3 mbar l/sec Seat material polyamid Body material Chrome plated brass PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 ISO 5145 None N 2 O N 2O 25E B 300bar 300 CGA V1 CGA S1.1 Various gases (*) VG * ¾"-16 UNF CCS 2000Psi 2000 UNI JIS CO 2 CO 2 ¾" NGT OBS 3000Psi 3000 JIS * gas or mixture must be confirmed
25 RPV VALVE 25 M978/M979/C878 STANDARD RPV IN LINE - High pressure brass cylinder valve for medical gases, O-ring seal type with residual pressure Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Safe, long, trouble free life under all service conditions - Designed and tested according EN ISO and EN ISO OPTIONS - Inlets: 17 E 25 E M 18 US threads - Filter - Burst disc safety device - Thread for dip tube connection - Chrome plating Ref catalog: MPR-EN-1115 PRODUCT SERIE FEATURES GAS SAFETY O 2 VARIOUS GASES WITH WITHOUT M978 M979 SPECIFICATIONS Working pressure 200 bar/ 2900 psi Seat orifice size 4 mm O-ring material EPDM Temperature range -25 C to +70 C handwheel material aluminium Body material Chrome plated brass Helium leak rate at pmax 10-3 mbar l/sec Seat material polyamid Specific M978: O 2 M9769: various gases sc878: O 2 + integrated valve PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 DIN DIN None N N 2 O N 2O M18X1,5 RCS Eu CO2/N2O EU Various gases (*) VG * CO 2 CO 2 * gas or mixture must be confirmed
26 26 RPV VALVE M100/M105/M040/M045/M200/M205 STANDARD CYLINDER VALVE - High pressure brass cylinder valve for medical oxygen - O-ring seal type Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Safe, long, trouble free life under all service conditions - Approved valve design - Testing according ISO and CGA U9 Standard OPTIONS - Inlets: 17 E 25 E M 18 US threads - Filter - Burst disc safety device - Thread for dip tube connection - Chrome plating Ref catalog: MPR-EN-1115 PRODUCT SERIE FEATURES GAS SAFETY O 2 CO 2 VARIOUS GASES WITH WITHOUT M100 M105 M040 M045 M200 SPECIFICATIONS Working pressure Temperature range Helium leak rate at pmax 232 bar -25 C to +70 C 10-3 mbar l/sec Seat orifice size Magnetic compatibility handwheel material M100/M105/M200/M205 : 4mm M040/M045: 8mm yes polyamid Seat material O-ring material Body material polyamid EPDM Chrome plated brass PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 300bar 3000 ISO 5145 ISO None N N 2 O N 2O 25E B CGA V1 CGA CGA S1.1 CGA Various gases (*) VG * ¾"-16 UNF CCS UNI UNI JIS JIS ¾" NGT OBS DIN DIN Eu CO 2 /N 2 O EU AFNOR BS SS AS AFNOR BS SS AS * gas or mixture must be confirmed
27 M972/M973/M974/M975 STANDARD CYLINDER VALVE SMALL CONE STANDARD CYLINDER VALVE 27 - High pressure brass cylinder valve for medical oxygen - O-ring seal type - Small cone inlet size Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque under up to 200 bar service pressure - MRI compatible - Designed and tested acc. EN ISO 10297, EN ISO Residual pressure setting 1-3 bar - Manufactured in cleanroom - Inlet with filter - Possibility of integrated gauge - OPTIONS - Inlet: 17E M18 M 14 - Without filter Ref catalog: MPR-EN-1115 PRODUCT SERIE FEATURES GAS SAFETY O 2 VARIOUS GASES WITH WITHOUT M972 M973 M974 M975 SPECIFICATIONS Working pressure 200 bar Seat orifice size 2.5 mm Seat material PA 6.6 Temperature range Helium leak rate at pmax -20 C to +70 C 10-3 mbar l/sec Residual pressure handwheel material 1-3 bar aluminium O-ring material Body material Filter material EPDM Chrome plated brass brass sintered PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 DIN DIN None N N 2 O N 2O M18X1,5 RCS Eu CO2/N2O EU Various gases (*) VG * CO 2 CO 2 * gas or mixture must be confirmed
28 28 STANDARD CYLINDER VALVE D113 PACKED VALVE - High pressure cylinder valve with RPV, packed needle stem design, for NO mixtures Can be connected with Ceodeux Meditec regulators KEY FEATURES - Freedom from seizure when used with corrosive gases - gas does not come into contact with the valve operating mechanism - Positive and effective operation - valve spindle is mechanically linked to the operating handwheel, which only requires low closing torque - Long life - valve spindle and seat are replaceable - Adjustable gland packing - in the unlikely event of a leakage occuring past the valve spindle, when opening the valve, rectification is readily achieved by retightening the gland packing nut - Low internal volume - this is particularly beneficial, when using the valve for hygroscopic, corrosive or high purity gases, here inert gas purging may be necessary before opening or after closing the valve - Left hand threaded counter screw to secure sealing mechanism even under excessive torque ~ 63 Ref catalog: MPR-EN-1115 ~ 123 ~ 7,5 ~ 39,5 SPECIFICATIONS Working pressure 200 bar/3000psi Flow coefficient Cv 0.3 Residual pressure 1 to 5 bar Temperature range -40 C to +70 C Seat orifice size 3,3 mm Helium leak rate at pmax 10-6 mbar l/sec 10-5 mbar l/sec 10-8 mbar l/sec Body material Stainless steel RPV seat material Viton PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety "NO mixture up to 1000 ppm ¾" NGT OBS 200bar 200 ISO 5145 ISO None N 25E B CGA V1 CGA CGA S1.1 CGA
29 SPECIAL NITRIC OXIDE CYLINDER VALVE 29 D413 TIED DIAPHRAGM - High flow cylinder valves with RPV, tied diaphragm seal type, for NO mixtures Can be connected with Ceodeux Meditec regulators KEY FEATURES - Reduced dead spaces and gas wetted volumes allow easy purging process - Freedom of internal threads and springs insures minimum particulate generation - Very low internal volume with minimum dead spaces. This is particularly beneficial, when using the valve for hygroscopic, corrosive, pyrophoric or high purity gases where inert gas purging is necessary before opening or after closing the valve - Freedom from seizure where used with corrosive gases.gas does not come into contact with the valve operating mechanism - Positive and effective operation, valve lower spindle is mechanically linked to the upper spindle and the operating handwheel - Backed up welded diaphragms provide a permanent and durable gas tight seal - O-Rings in the gland and on spindle guarantee a secondary sealing - Threaded vent hole Ref catalog: MPR-EN-1115 ~ 54 ~ 120 ~ 7,5 ~ 56 SPECIFICATIONS Working pressure 200 bar/3000 psi Flow coefficient Cv 0,35 Body material 316L Stainless steel Temperature range -40 C to +70 C Seat orifice size 4 mm Residual pressure 1 to 5 bar Helium leak rate at pmax 10-8 mbar l/sec Gas wetted materials PCTFE RPV seat material Viton PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety "NO mixture up to 1000 ppm ¾" NGT OBS 200bar 200 ISO 5145 ISO None N 25E B CGA V1 CGA CGA S1.1 CGA
30 30 SPECIAL NITRIC OXIDE CYLINDER VALVE M966 PIN INDEX CYLINDER VALVE - High pressure brass cylinder valve for medical gases and oxygen, - with yoke outlet connection (PIN INDEX System) - O-ring-seal Can be connected with Ceodeux Meditec regulators KEY FEATURES - Low operating torque - MRI compatible - Key-operated or handwheel operating system - Safe, long, trouble-free life under all service conditions - Testing according EN ISO and CGA U9 Standard OPTIONS - Inlets: 17E 19E 19T LT T M18 US threads - Natural brass - Burst disc safety device - Fusible metal safety device - Other filter (lang) I.E: Alpinox Pin index Ref catalog: MPR-EN-1115 ~ 103 ~ 32 SPECIFICATIONS Working pressure 232 bar Seat orifice size 2.5 mm Seat material PA 6.6 Temperature range -25 C to +70 C Magnetic compatibility yes O-ring material EPDM Helium leak rate at pmax 10-3 mbar l/sec Key operated chrome plated Handwheel material plastic switch blade Body material Filter material Chrome plated brass brass sintered PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 ISO 407 ISO None N N 2 O N 2O M18X1,5 RCS CGA CGA CGA S1.1 CGA Various gases (*) VG * 25E B CO 2 CO 2 * gas or mixture must be confirmed
31 PIN INDEX VALVE 31 M650 PIN INDEX RPV CYLINDER VALVE - PIN INDEX valve for medical gases with active residual pressure function Can be connected with Ceodeux Meditec regulators KEY FEATURES - High tensile brass (CZ115) - Low operating torque - MRI compatible - Key-operated or handwheel operating system - Design and tested acc. EN849, EN ISO407, EN ISO15996 and CGA V9 - Residual pressure - Manufacturing in clean room OPTIONS - Inlets: 17E 19E 19T LT T M18 US threads - Natural brass - Burst disc safety device - Fusible metal safety device - Other filter (lang) I.E: Alpinox Pin index Ref catalog: MPR-EN-1115 SPECIFICATIONS Working pressure 232 bar Cv 0.08 O-ring material EPDM Temperature range Helium leak rate at pmax Seat orifice size -25 C to +70 C 10-3 mbar l/sec 2.5 mm Magnetic compatibility yes Key operated chrome plated handwheel material removable plastic switch blade Seat material PA 6.6 Body material Filter material chrome plated / natural brass brass sintered PRODUCT CONFIGURATOR Gas Inlet Connection Working Pressure Outlet connection HP Safety O 2 O 2 17E A 200bar 200 ISO 407 ISO None N N 2 O N 2O M18X1,5 RCS CGA CGA CGA S1.1 CGA Various gases (*) VG * 25E B CO 2 CO 2 * gas or mixture must be confirmed
32 32 NOTES
33 33 NOTES
34 A WORLD OF GAS CONTROL SOLUTIONS COMPLETE SOLUTIONS FROM SOURCE TO PROCESS. ROTAREX is helping engineers worldwide to get better gas results: from ultra high purity production and medical care facilities to industrial and LPG applications, as well as alternative energy vehicles, fire suppression, diving, aerospace, cryogenics, laboratory, petro-chemical and welding. ROTAREX applies over 90 years of know-how and experience to custom design, develop and manufacture the high performance valves, regulators and fittings to suit your needs, all in one hand. Discover the difference ROTAREX can make in your world. CYLINDER VALVES EQUIPMENT FIRETEC AUTOMOTIVE LPG/SRG MEDITEC
35 INDUSTRIAL CYLINDER VALVES UHP CYLINDER VALVES MEDICAL VALVES & REGULATORS SPECIALTY GAS VALVES REGULATORS & FITTINGS CRYOGENIC VALVES AUTOMOTIVE FIRE SUPPRESSION LPG VALVES REGULATORS & GAUGES WATERTEC AUSTRALIA / BRASIL / CHINA / FRANCE / INDIA / ITALY / JAPAN / LUXEMBOURG / MIDDLE EAST / RUSSIA / SINGAPORE / SPAIN / THAILAND / USA
36 WORLDWIDE HEADQUARTERS Ceodeux Meditec Customer Service 24 rue de Diekirch, B.P Lintgen, Luxembourg Tel.: Fax: info@meditec.rotarex.com REGIONAL / COUNTRY HEAD QUARTERS NORTH AMERICA EUROPE ASIA OCEANIA USA Rotarex North America 221 Westec Drive Westmoreland Technology Park I Mt. Pleasant, Pennsylvania USA Tel.: Fax: info@northamerica.rotarex.com SOUTH AMERICA BRASIL Rotarex Brazil Ltda Cond. Ind. Portal da Anhanguera Estr. Municipal Gov. Mário Covas, S/N Bairro Macuco -Valinhos São Paulo Brazil Tel.: Fax: info@brazil.rotarex.com FRANCE, BENELUX, GERMANY 24, rue de Diekirch, BP 19 L-7505 Lintgen, Luxembourg Tel.: Fax: salesequipment@rotarex.com ITALY Rotarex Italia S.r.l. 46 Via Giacomo Matteotti I-25080, Ciliverghe di Mazzano (BS) Italy Tel.: Fax: info@italia.rotarex.com SPAIN Rotarex Spain C/Alcala, 4 Oficina Madrid Tel.: +34 (91) Mobile: + 34 (650) info@spain.rotarex.com RUSSIA Rotarex Rus Tverskaya street, 20/1 bldg. 1 of , Moscow Russia Tel.: Skype: rotarexrus info-russia@rotarex.com POLAND Rotarex Polska 13 Gröbli PL Brzeg, Poland Tel.: Fax: info@poland.rotarex.com MIDDLE EAST Rotarex Middle East Jebel Ali Free Zone - Lob 17, Office 415 P.O. Box Dubai, U.A.E. Tel.: +971 (0) Fax: +971 (0) info@middle-east.rotarex.com CHINA Rotarex Star 60 Yuan Zhong Road Shanghai Nanhui Industrial Zone , Shanghai China Tel.: Fax: info@china.rotarex.com SINGAPORE Rotarex Fareast Pte Ltd 10 Ubi Crescent Ubi Techpark, Lobby C, # Singapore Tel.: Fax: info@singapore.rotarex.com JAPAN Rotarex Japan Ltd 6F, Yawaragi Bldg., Taito Taito-ku, Tokyo JAPAN Tel.: Mob.: Fax: info@japan.rotarex.com INDIA Rotarex ENGG. PVT. LTD. C-105, Mahindra Apartments Vikaspuri, New Delhi mob.: atul.nigam@rotarex.in THAILAND Rotarex (Thailand) Co Ltd. 297, Wanglee Tower 3rd floor, Unit C, Surawong Road Suriyawong, Bangrak, Bangkok Thailand Tel.: info@thailand.rotarex.com SOUTH KOREA Rotarex Luz Tech Co , 547 Yongsan-dong Yuseong-gu Taejon, Korea Tel.: Fax: info@rotarex.co.kr AUSTRALIA Rotarex Australia/New Zealand Hornsby Heights, Sydney, NSW, 2077 Tel.: info@australia.rotarex.com ROTAREX S.A. CEODEUX MEDITEC - CEODEUX S.A. MCV-EN-1115
MEDICAL CYLINDER VALVES
MEDICAL CYLINDER VALVES 3 1 Medical integrated valve for oxygen air and medical mixture 1.1 ALIONE 1.2 ALPINOX-valve 1.3 ALPINOX-valve compact 2 Cylinder valve with RPV for oxygen and medical gases -
More informationMediCal gas solutions
MediCal gas solutions Who is CeodeuX MediteC? CeodeuX MediteC WhiCh is the MediCal division of the rotarex group, BeneFits of the 90 years of experience of the CoMPany. More than 20 years in the medical
More informationMEDICAL CYLINDER VALVES
MEDICAL CYLINDER VALVES 3 TABLE OF CONTENTS INTRODUCTION P.004 Ceodeux meditec solutions P.004 Quality first... P.004 The main medical gases P.005 Product range overview P.006 Technology overview P.008
More informationOVER 90 YEARS LEADERS IN SPECIALIZED GAS EQUIPMENT OF GAS EXPERTISE s s ALL MAJOR GAS APPLICATIONS
Gas equipment OVER 90 YEARS OF GAS EXPERTISE 1950 s 1922 - CEODEUX founded as a C02 producer by A.T. Schmitz 1926 - First valve innovations for C02, Fire and Acetylene - Edgard Schmitz becomes CEO - Enter
More informationALPI-CONNECT KEY FEATURES REGULATORY COMPLIANCE
ALPI-CONNECT 2 ALPI-CONNECT ALPICONNECT is CEODEUX MEDITEC new innovative terminal unit for medical gas pipline systems into healthcare facilities Integrated into hospital environment as Operating Rooms
More informationPRECISE & COMPACT POINT OF USE FOR LABORATORY APPLICATIONS
PRECISE & COMPACT POINT OF USE FOR LABORATORY APPLICATIONS 3 TABLE OF CONTENTS C790 SERIE LINESTAR PRODUCT FEATURES P.006 Mounted versions P.006 C792 Panel mounted version P.006 C793 Wall mounted version
More informationPRESSURE REDUCTION FLOWMETERING, QUICK COUPLING PROBES AND ACCESSORIES
PRESSURE REDUCTION FLOWMETERING, QUICK COUPLING PROBES AND ACCESSORIES 1 3 1 - ALPINOX: oxygen Regulator - Medical oxygen regulator with flowmeter. - Medical oxygen regulator with flowmeter and Quick
More informationPRECISE & COMPACT POINT OF USE FOR LABORATORY APPLICATIONS
PRECISE & COMPACT POINT OF USE FOR LABORATORY APPLICATIONS 3 TABLE OF CONTENTS C790 SERIE LINESTAR PRODUCT FEATURES P.006 Mounted versions P.006 C792 Panel mounted version P.006 C793 Wall mounted version
More informationPTFE AND STAINLESS STEEL HOSES
PTFE AND STAINLESS STEEL HOSES 3 TABLE OF CONTENTS DESCRIPTION P.004 Description of FX01 hoses P.004 Description of FX02 hoses P.004 Description of FX06 hoses P.005 SPECIFICATIONS OF FX01, FX02 AND FX06
More informationPRESSURE REGULATORS, FLOW METERS, QUICK COUPLING PROBES AND ACCESSORIES
PRESSURE REGULATORS, FLOW METERS, QUICK COUPLING PROBES AND ACCESSORIES 3 TABLE OF CONTENTS INTRODUCTION P.004 CEODEUX MEDITEC solutions P.004 Quality first... P.004 The main medical gases P.005 PRODUCT
More informationValve with Integrated Pressure Regulator for medical OXYgen
Valve with Integrated Pressure Regulator for medical OXYgen Handling and performing ALL IN ONE solution Compact and light design User friendly Suitable for home care, intensive and baby care Use for oxygen,
More informationCENTRAL GAS SUPPLY SYSTEMS COMPONENTS AND ACCESSORIES
CENTRAL GAS SUPPLY SYSTEMS COMPONENTS AND ACCESSORIES 3 TABLE OF CONTENTS INTRODUCTION P.004 PRODUCT RANGE OVERVIEW P.008 TECHNOLOGY OVERVIEW P.010 Supply boards P.010 Switchover Boards P.010 Pressure
More informationPRESSURE REGULATORS AND FLOWMETERS, ALL MEDICAL GASES
PRESSURE REGULATORS ALL MEDICAL GASES In this section we propose our pressure regulators (FM series, MU and MERCURY ) and our Rs flowmeters for applications other than oxygen therapy (presented in the
More informationREFERENCE GUIDE ON MEDICINAL GAS CYLINDER VALVES
REFERENCE GUIDE ON MEDICINAL GAS CYLINDER VALVES AIGA 097/17 Asia Industrial Gases Association 52 Jurong Gateway Road,JEM, #15-02, Singapore 608550 Tel : +65 6276 0160 Fax : +65 6274 9379 Internet : http://www.asia.org
More informationINNOVATIVE & COMPLETE GAS SUPPLY SYSTEM FOR MEDICAL AND HOSPITAL APPLICATIONS
INNOVATIVE & COMPLETE GAS SUPPLY SYSTEM FOR MEDICAL AND HOSPITAL APPLICATIONS ALPI-LINE THE ADAPTED SOLUTION FOR MEDICAL GAS SUPPLY IN HOSPITALS Ceodeux Meditec is the medical range of the Rotarex Group
More informationHigh Pressure Cylinder Valves
High Cylinder Valves CBA series Commercial and POL Style Acetylene Cylinder Valves O-Ring seal type 8 CBO series Vertical Outlet Acetylene Valve with Handwheel for Collar Style Cylinders 9 CBH/CBI series
More informationTHE GAS CONFIDENCE COMPANY
THE GAS CONFIDENCE COMPANY WORLD LEADERS IN VALVES, REGULATORS AND INSTRUMENTATION FOR PRESSURIZED GAS SYSTEMS Rotarex is a world leader in valves and equipment for pressurized gas applications. Our commitment
More informationDescription Advanced Features Typical Applications
Series single stage, brass barstock line regulator Description Advanced Features Typical Applications The Series regulators are intended for secondary pressure control of noncorrosive, high purity or liquefied
More informationWheel operated Residual Pressure Valves
Wheel operated esidual Pressure Valves Offline Series CPV-10/O (For Oxygen,Inert,High purity and Medical gases) Series CPV-10/C (For Carbon dioxide and Carbon dioxide gas mixtures) Protects cylinder contents.
More informationREGULATORS FLOWMETERS HUMIDIFIERS. Professional GAUGES ASSESSORIES. Medical Apparatus. and Assessories ISO 13485/ISO 9001 CERTIFICATION
Medical Apparatus REGULATORS FLOWMETERS Professional Medical Apparatus and Assessories HUMIDIFIERS GAUGES ASSESSORIES ISO 13485/ISO 9001 CERTIFICATION Company Profile MORRIS ENGINEERING WORKS LTD. was
More informationREGULATORS FOR SPECIFIC APPLICATIONS
SINGLE-STAGE REGULATORS FOR NITROUS OXIDE AND CARBON DIOXIDE (MODELS SG9011, SG9012, SG9014) Nitrous Oxide and Carbon Dioxide frequently cause ordinary regulators to freeze up. Models SG9011, SG9012 and
More informationMicro Dial-Flowmeter. Instructions for Use
Micro Dial-Flowmeter Instructions for Use 702-0082.8 May 2014 1. Symbols Warning! Caution! Indicates a potentially hazardous situation which, if not avoided, could result in personal injury to the user
More informationTITAN Oxygen Regulators
EMS OXYGEN REGULATORS TITAN Oxygen Regulators EMS TITAN SERIES OXYGEN EMS AND FIRE SERVICE APPLICATIONS CLICK-STYLE REGULATOR Whether its EMS, ambulance, fire rescue or tactical medical use, Titan Oxygen
More informationOXYGEN THERAPY FLOWMETERS, REUSABLE AND SINGLE-PATIENT HUMIDIFIERS, PRESSURE REGULATORS, FLOW SELECTORS
OXYGEN THERAPY The line of oxygen therapy devices includes variable area flowmeters, calibrated holes dial flowmeters, pressure reducers with their cylinder connections, humidifiers, flow selectors and
More informationOxygen Dialflow Meter. Instructions for Use
Oxygen Dialflow Meter Instructions for Use 702-0031.12 December 2017 1. Symbols Warning! Caution! Indicates a potentially hazardous situation which, if not avoided, could result in injury to the patient,
More informationWheel operated residual pressure cylinder valve (Inline) in O-ring seal design for technical and medical gases
Wheel operated residual pressure cylinder valve (Inline) in O-ring seal design for technical and medical gases IRPV-10 I/O IRPV-10 I/C For oxygen, inert, high purity and medical gases For carbon dioxide
More informationNEW Edge Series Products: OUTFITS and REGULATORS
NEW Edge Series Products: OUTFITS and REGULATORS NOW Including ESS3 Models and More Edge Series Outfits User Friendly Advanced Design Outstanding Flow Performance Unsurpassed Safety www.victoredge.com
More informationOxygen Dialflow Meter. Instructions for Use
Oxygen Dialflow Meter Instructions for Use 702-0031.9 May 2014 1. Symbols Warning! Caution! Indicates a potentially hazardous situation which, if not avoided, could result in personal injury to the user
More informationMEDAP-MOBILE GAS SUPPLY
MEDAP-MOBILE GAS SUPPLY This document is intended to provide information to an international audience outside of the US. MOBILE GAS SUPPLY 3 MOBILE GAS SUPPLY FOR TRANSPORTATION AND WARD PRESSURE REGULATORS,
More informationSPECIFICATIONS. Approximate Weight: 10 oz. Surface Finish: Ra micro inch or less MATERIALS OF CONSTRUCTION
DIFFUSION-RESISTANT, DIAPHRAGM SEAL, EXCESS FLOW SHUT-OFF VALVES (FS SERIES) FS Series Excess Flow Shut-Off Valves are designed to automatically shut-off the delivery of gas in a line if the flow exceeds
More informationSpecialty Gas Equipment Catalogue
THE HARRIS PRODUCTS GROUP The Harris Products Group was formed by combining two strong names in the welding business - Harris Calorific and J.W. Harris. The Harris Products Group is a world leader in metalworking
More informationPrecision matters. HiQ equipment for specialty gases.
Precision matters. HiQ equipment for specialty gases. Pure, precise, reliable solutions. HiQ equipment. The application of specialty gases demands well-founded expertise and professional know-how. HiQ
More informationNEW EDGE SERIES REGULATORS & OUTFITS
WE LISTENED. WE DELIVERED. NEW EDGE SERIES REGULATORS & OUTFITS Victor Introduces the Newest Addition to the EDGE Series: The EHP3 High Pressure Regulator. EDGE Regulators Now Include These Models EHP3
More informationCRYOGENIC SERIES Regulators, Pressure Gauges, Shut-off Valves, Relief Valves Technology for a Better Future
www.genstartech.com Regulators, Pressure Gauges, Shut-off Valves, Relief Valves CRYOGENIC SERIES Technology for a Better Future GENTEC CRYOGENIC SERIES Cryogenic Shut-off Valves Cryogenic Relief Valves
More informationWorld Area Differences Technical Information
World Area Differences Technical Information DMISC2047X02 This document is to give more information about the following: Porting & Threads Cleaning Procedures Conversion Tables PORTING & THREADS NPT (National
More informationTHE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401
THE MF-400 SERIES Operating and Service Manual Series includes all variants of MF-400/401 Issue A October 2013 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More informationTechnical Specification
Medical Gas Terminal Units (Gas Outlet Points) Technical Specification EN 9170-1 Terminal Unit Product Description CPX Terminal Units comprise a first fix, second fix and check valve. The first fix assembly
More informationD Quality and Precision you can Trust in Oxygen Administration CONVENTIONAL FLOWMETER DIGITAL FLOWMETER COMPACT FLOWMETER
D-10023-2009 Quality and Precision you can Trust in Oxygen Administration CONVENTIONAL FLOWMETER DIGITAL FLOWMETER COMPACT FLOWMETER 02 MT-3287-2003 Administration of oxygen The use of oxygen therapy in
More informationNonrefillable Cylinders
Nonrefillable Cylinders A DIVISION OF NORCO, INC. Norlab, the Specialty Gas Division of Norco, Inc., has been producing and distributing calibration mixtures and pure specialty gases in refillable and
More information9/6/11 RSPT Medical Gas Therapy. Manufacture, Storage and Delivery of Medical Gases Part 1
1 RSPT 1410 Manufacture, Storage and Delivery of Medical Gases Part 1 Cairo, Respiratory Care Equipment p. 26-58 Wilkins, Fundamentals of Respiratory Care p. 843-866 Medical Gas Therapy 2 is the most commonly
More informationPRESSURE CONTROL REGULATORS
REGULATOR HARRIS STYLE SINGLE STAGE 201 Series Medium Duty Single stage construction Forged brass body for maximum strength Chrome bonnet Neoprene diaphragms Sintered metal inlet filter to trap impurities
More informationR133 HELYON. Brass high pressure regulator, suitable for compressed air, gas and liquid
R133 Brass high pressure regulator, suitable for compressed air, gas and liquid HELYON 5 Chemin du Jubin 6957 DARDILLY Tél. +33 () 7 5 16 7 - Fax +33 () 7 5 16 71 FEATURES High pressure regulator for cylinder
More informationSpecialty Gases & Equipment ISO 9001: 2008 CERTIFIED. A Division of Norco, Inc.
Specialty Gases & Equipment ISO 9001: 2008 CERTIFIED A Division of Norco, Inc. Located in Boise Idaho, Norlab has been producing and distributing calibration gas mixtures and specialty gases in refillable
More informationAIR/OXYGEN BLENDER INSTRUCTION MANUAL
BIO-MED DEVICES AIR/OXYGEN BLENDER INSTRUCTION MANUAL CATALOG #2120 REV 042203 BIO-MED DEVICES INC. 1445 BOSTON POST ROAD, GUILFORD, CT 06437 (203) 458-0202 FAX (203) 458-0440 www.biomeddevices.com TABLE
More informationproduct range overview P.004 P.006 Switch over Boards Quality Standards Pressure Regulator Technology P.013 Technical Parameters
supply and SWITCH OVER BOARDS table of contents product range overview P.4 technology overview P.6 -- Supply Boards P.6 -- Switch over Boards P.6 -- Quality Standards P.7 -- Pressure Regulator Technology
More informationI. Subject: Compressed gas cylinders, regulators, and portable liquid systems.
I. Subject: Compressed gas cylinders, regulators, and portable liquid systems. II. Objective: To provide safe and effective use, storage, and transport of therapeutic gases. II. Procedure: A. Compressed
More informationHP/UHP Spring-Loaded Regulator
Description HP (High Purity) and UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise dead areas where contaminants
More informationTHE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301
THE HF-300 SERIES Operating and Service Manual Series includes all variants of HF-300/301 Issue A July 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 3.1. Spring Loaded...
More informationTHE BP-301 SERIES. Operating and Service Manual. Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv)
THE BP-301 SERIES Operating and Service Manual Series includes all variants of BP-301 (LF 0.1Cv / MF 0.5Cv) Issue B October 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation...
More informationISO INTERNATIONAL STANDARD. Gas cylinders Cylinder valves with integrated pressure regulators Specification and type testing
INTERNATIONAL STANDARD ISO 22435 First edition 2007-09-01 Gas cylinders Cylinder valves with integrated pressure regulators Specification and type testing Bouteilles à gaz Robinets de bouteilles avec détendeur
More informationISO INTERNATIONAL STANDARD. Flow-metering devices for connection to terminal units of medical gas pipeline systems
INTERNATIONAL STANDARD ISO 15002 Second edition 2008-07-01 Flow-metering devices for connection to terminal units of medical gas pipeline systems Dispositifs de mesure de débit pour raccordement aux prises
More informationRefrigerant Gases Valves
Refrigerant Gases Valves RUS series Single Outlet Compact Refrigerant Recovery Valves 46 RDU series Diaphragm Packless Multivalves for Refrigerant Gases 47 RBV series Single Outlet Diaphragm Packless Valves
More informationUSE OF RESIDUAL PRESSURE VALVES
USE OF RESIDUAL PRESSURE VALVES AIGA 063/16 Revision of AIGA 063/14 Asia Industrial Gases Association 3 HarbourFront Place, #09-04 HarbourFront Tower 2, Singapore 099254 Tel : +65 6276 0160 Fax : +65 6274
More informationA BRIEF TUTORIAL ON GAS HANDLING EQUIPMENT
TABLE OF CONTENTS BACK PRESSURE REGULATORS...26 CGA CONNECTION DRAWINGS...102 CGA CYLINDER CONNECTIONS AND GASKETS...98 CHANGEOVER MANIFOLDS...60-63,65 CHECK VALVES...70 CONVERSION TABLES...103 CUSTOM
More information61 Series Pilots for Pilot-Operated Pressure Reducing Regulators
61 Series Pilots for Pilot-Operated Pressure Reducing Regulators June 2011 Introduction 61 Series pilots are used with Types 1098-EGR and EZL pressure reducing regulators. These pilots can also be integrally
More informationInstallation Instructions and valve Maintenance Rev. 0 of 21/09/15
ASSEMBLING PROCEDURE AND VALVE MAINTENANCE 1.0.... Safety Information 2.0.. INTRODUCTION 3.0 VARIATIONS 4.0..ASSEMBLING PROCEDURE FOR THE STEM 5.0 ASSEMBLING PROCEDURE FOR OUTLET CONNECTIONS 6.0 PROCEDURE
More informationDataSheet for Gas Control Regulators
Scientific & Technical Gases DataSheet for Gas Control Regulators Units 1&2, Speedwell Road Parkhouse Ind. Estate East Newcastle-Under-Lyme ST5 7RG UK Tel: 44-1782 566897 Fax: 44-1782 564906 Email: info@stgas.eu
More informationOxyTOTE PORTABLE OXYGEN SYSTEM
OxyTOTE PORTABLE OXYGEN SYSTEM OxyTOTE OXYGEN REGULATOR WITH SURECLICK FEATURE The OxyTOTE regulator is perfect for transporting and dispensing oxygen in one easy-to-use package. With Western s innovative
More informationPetro-Chemical & Analyzer Sampling Systems
Petro-Chemical & Analyzer Sampling Systems Pressure control solutions for your industry. The Tescom brand offers a comprehensive range of regulators, valves and changeover systems that are ideal for analyzer
More informationSG1 Series Regulators - Pressure Reducing
SG1 Series Regulators - Pressure Reducing DSG131X Specifications For questions about this product, please consult TESCOM. OPERATING PARAMETERS Pressure rating per criteria of CGA E-; ASME B31; ASME BPVC
More informationR300 HELYON. Brass high pressure regulator, for compressed air, gas and liquids
HELYON 5 Chemin du Jubin 69570 DARDILLY Tél. +33 (0)4 72 52 16 70 - Fax +33 (0)4 72 52 16 71 R300 Brass high pressure regulator, for compressed air, gas and liquids FEATURES Pressure regulator for inlet
More informationDESIGN CONSIDERATIONS AND GUIDANCE FOR THE SAFE USE OF MEDICAL GAS VIPR
DESIGN CONSIDERATIONS AND GUIDANCE FOR THE SAFE USE OF MEDICAL GAS VIPR IGC & MGC Doc 180/13/E EUROPEAN INDUSTRIAL GASES ASSOCIATION AISBL AVENUE DES ARTS 3-5 B 1210 BRUSSELS Tel : +32 2 217 70 98 Fax
More informationPetro-Chemical & Analyzer Sampling Systems
Petro-Chemical & Analyzer Sampling Systems Pressure control solutions for your industry. The Tescom brand offers a comprehensive range of regulators, valves and changeover systems that are ideal for analyzer
More information7625 West New York Street Indianapolis IN Phone: Fax: Order Desk:
Flotec was incorporated on June 30, 1983 as a wholly owned subsidiary of Davidson, Inc. Since the beginning, the core activity has been manufacturing for the medical, industrial, and OEM markets. The products
More informationModel 1800 PFM Series Regulator. Technical Bulletin
Model 0 PFM Series Regulator Technical Bulletin Model 0 PFM Series Regulator 0 Elster American Meter The 0 PFM Series regulators are designed to control natural gas, air, nitrogen, carbon dioxide, propane
More informationOperating Manual. R280 Pressure regulator made of brass. 1. Intended Use
Pressure regulator made of brass Operating Manual 1. Intended Use Line or outlet pressure regulators- /reducer for Air, gases and liquids which is designed to effect reduction to a downstream pressure
More informationPressure Regulator. Instructions for Use
Pressure Regulator Instructions for Use 702-0083.9 December 2017 1. Symbols Warning! Caution! Indicates a potentially hazardous situation which, if not avoided, could result in injury to the patient, the
More informationPortable helium spray set
Portable helium spray set User manual N 521214-01 DATE ORIGINATOR REV. COMMENTS 12/11/2012 IBT A Creation 08/25/2015 LRT B Section 4.2 updated 1 Disclaimer and limitation of liability The information contained
More informationT208VR Series Tank Blanketing Vacuum Regulator
February 2014 T208VR Series Tank Blanketing Vacuum Regulator Figure 1. Typical T208VR Series Vacuum Regulator Introduction The T208VR Series direct-operated vacuum regulators are used where a decrease
More information64 Series Pressure Reducing Regulators
Instruction Manual Form 1245 64 Series March 2006 64 Series Pressure Reducing Regulators W1943 Figure 1. 64 Series Regulator Introduction Scope of Manual This manual provides instructions for the installation,
More informationMounting and Operating Instructions EB 3007 EN. Self-operated Pressure Regulators. Differential Pressure Regulators (opening) Type Type 42-25
Self-operated Pressure Regulators Differential Pressure Regulators (opening) Type 42-20 Type 42-25 Type 42-20 Differential Pressure Regulator Type 42-25 Differential Pressure Regulator Mounting and Operating
More informationContent. 1. Basic Product information. 2. Standard Equipment. 3. Special Gas Equipment. 4. Accessory. 5. Charts 6. GCE - -
Content 1. Basic Product information 1.1 Product range 2 1.2 Product basics 3 1.3 Product selection guide 5 1.4 s 6 1.5 Regulators overview 7 2. Standard Equipment 2.1 Regulators series 5 1 2.2 Regulators
More informationDialflow Regulator. Instructions for Use
Dialflow Regulator Instructions for Use 702-0030.11 May 2014 1. Symbols Warning! Caution! Indicates a potentially hazardous situation which, if not avoided, could result in personal injury to the user
More information1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
More informationPORTABLE MEDICAL AIR SYSTEM
ALL-IN-ONE CONVENIENCE PORTABLE MEDICAL AIR SYSTEM 2007 Western Medica AIRTOTE Western s new AirTOTE portable medical air system brings a new level of simplicity and cost Portable Medical Air System with
More informationSG2 Series Regulators - Pressure Reducing
SG2 Series Regulators - Pressure Reducing DSG2232X Specifications For questions about this product, please consult TESCOM. OPERATING PARAMETERS Pressure rating per criteria of CGA E-; ASME B31; ASME BPVC
More informationRESIDENTIAL REGULATORS
RESIDENTIAL REGULATORS Type B NG Process Management TM B NG Regulators Description! BODY RESISTANT TO HIGHER PRESSURES Various Springs Adaptable to various fluids (Natural Gas, LPG, Manufactured Gas, etc.)!
More informationGCE CENTRAL GAS SYSTEMS THE DRINKS DISPENSE INDUSTRY EQUIPMENT FOR GAS SUPPLIER SYSTEMS
THE DRINKS DISPENSE INDUSTRY EQUIPMENT FOR GAS SUPPLIER SYSTEMS THE GCE BUSINESS GCE has almost 100 years of experience in the manufacture and supply of high pressure gas equipment. During this time the
More informationPressure Reducing Valve DMV 750 set range: bar
Pressure Reducing Valve DMV 750 set range:.0-6.0 bar Advantage pressure setting possible at any time, also during operation hermetically sealed by valve diaphragm high level of operating safety and long
More informationGas Pressure Regulator HON 200
Product information serving the gas industry worldwide Applications, characteristics, technical data Application Gas supply to municipal, industrial and individual consumers Regulator for low-load rails
More informationTable of Contents. Operating Instructions. Resource v.2 Conserving Regulator
Operating Instructions Table of Contents Resource v.2 Conserving Regulator Safety Information Device Precautions Introduction Product Features Product Specifications Feature Illustrations Set Up Usage
More informationSafety Relief Valve HON 832
Safety Relief Valve HON 832 product information serving the gas industry worldwide Application, characteristics, technical data Application 2 As leak gas SRV with internal vent connection (function class
More informationPropor tional Re lief Valve s
www.swagelok.com Propor tional Re lief Valve s R Series Liquid or gas service Set pressures from 10 to 6000 psig (0.68 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections Proportional Relief Valves
More informationP9000 DESCRIPTION. For parts requiring RoHS compliance, please contact factory. P February /6
P9000 High accuracy through digital compensation High thermal stability Rugged stainless steel construction Ideal for test stands High burst pressure limit DESCRIPTION The P9000 Series is a range of advanced,
More information1805 Series Relief Valves
Instruction Manual Form 1211 1805 Series October 2011 1805 Series Relief Valves! WARNING Failure to follow these instructions or to properly install and maintain this equipment could result in an explosion
More informationCENTRAL GAS SUPPLY SYSTEMS : CYLINDER BATTERIES AND HIGH PRESSURE HOSES
P0170E-1.DOCX/08.16/MG CENTRAL GAS SUPPLY SYSTEMS : CYLINDER BATTERIES AND HIGH PRESSURE HOSES With a Central Gas Supply System, individual work places or gas take-off stations are supplied with gas through
More informationInstruction manual. for. high purity gas pigtails 200 bar / 300 bar
Instruction manual for high purity gas pigtails 200 bar / 300 bar Contents Contents... 2 1. Preface... 3 1.1 Overview... 3 1.2 General... 3 1.3 Intended use... 4 1.4 Personnel requirements... 4 2. For
More information1800C and 1800C-HC Service Regulators
SB 855.9 800C and 800C-HC Service Regulators Maximum Pressure 5 Table of Contents 800C Regulator Information...................... 800C-HC Regulator Information.................. 800C and 8C Service Regulators...............
More informationDMK 458. Pressure Transmitter for Marine and Offshore. Ceramic Sensor. accuracy according to IEC 60770: standard: 0.25 % FSO option: 0.
Pressure Transmitter for Marine and Offshore Ceramic Sensor accuracy according to IEC 60770: standard: 0.5 % FSO option: 0. % FSO Nominal pressure from 0... 40 mbar up to 0... 0 bar Output signals -wire:
More informationAssembly-, installation- and maintenance instruction manual for bladder accumulators IBV / EBV , top reparable
Page 1 von 8 Assembly-, installation- and maintenance instruction manual for bladder accumulators IBV / EBV 100-575, top reparable Content Seite 0 Legend 2 1 Overview 2 2 Accumulator assembly and installation
More informationType 310A-32A Pressure Reducing Regulator and Type 310A-32A-32A Working Monitor Regulator
January 2009 Type 310A-32A Pressure Reducing Regulator and Type 310A-32A-32A Working Monitor Regulator Introduction The Type 310A pilot-operated high-pressure regulator (Figure 1) is used where high capacity
More informationTHE BP-690 SERIES. Operating and Service Manual. Series includes all variants of BP-LF/MF-690/691
THE BP-690 SERIES Operating and Service Manual Series includes all variants of BP-LF/MF-690/691 Issue B April 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special
More information98695A01 - THE CONCEPT OF THE DIVATOR FAMILY
98695A01 - THE CONCEPT OF THE DIVATOR FAMILY The History of Interspiro Respiratory Protection The History of Divator MK I The History of Divator MK II Scuba Diving Philosophy Government Customers Quality
More informationGas Pressure Regulator HON 300
Product information serving the gas industry worldwide Applications, characteristics, technical data Applications direct acting gas pressure regulator, for systems in accordance with DVGW working instruction
More informationsafety Shut-Off Valve HON 721
safety Shut-Off Valve HON 7 product information serving the gas industry worldwide safety shut-off valve HON 7 safety shut-off valve HON 7 Application, Characteristics, Technical Data Application safety
More informationTank Blanketing Pressure Regulators RHPS Series
www.swagelok.com Tank Blanketing Pressure Regulators RHPS Series Types: pressure reducing and vapor recovery 16L stainless steel construction 1/2, 1, and 2 in. end connections Working pressures up to 22
More informationInstallation, Operation and Maintenance Manual for Back Pressure Regulator
Installation, Operation and Maintenance Manual for Back Pressure Regulator Model 8860 2009 Groth Corporation IOM-8860 Rev. B 12541 Ref. ID: 95565 Page 2 of 13 Table of Contents I. INTRODUCTION 3 II. DESIGN
More informationSafety Shut-Off Valve HON 720
Safety Shut-Off Valve HON 70 Product information serving the gas industry worldwide Application, Characteristics, Technical Data Application main safety device for gas pressure regulating stations suitable
More informationProportional Relief Valves
www.swagelok.com Proportional Relief Valves R Series Liquid or gas service Set pressures from 10 to 6000 psig (0.68 to 413 bar) 1/4 and 1/2 in. and 6 to 12 mm end connections 2 Proportional Relief Valves
More informationPressure regulators for a wide range of applications
Pressure regulators Pressure regulators for a wide range of applications Pressure regulators are used to reduce a gas from a higher input pressure (p1) to a lower output pressure (p2). They are used everywhere
More information