PRESSURE REGULATORS, FLOW METERS, QUICK COUPLING PROBES AND ACCESSORIES

Transcription

1 PRESSURE REGULATORS, FLOW METERS, QUICK COUPLING PROBES AND ACCESSORIES

2

3 3 TABLE OF CONTENTS INTRODUCTION P.004 CEODEUX MEDITEC solutions P.004 Quality first... P.004 The main medical gases P.005 PRODUCT RANGE OVERVIEW P.006 PRESSURE REGULATORS STANDARD RESPIRATORY THERAPIES P.008 ALPINOX medical oxygen regulator P.008 MINIOX medical oxygen regulator P.010 PRESSURE REGULATORS SPECIAL THERAPIES (ASSISTED) P.012 Series BSC 280/380 P.012 Series BSC 290/390 P.014 Series DI 135 P.016 IN-HOSPITAL THERAPY EQUIPMENT P.018 M730 Alpinox Flowmeter with calibrated orifices P.018 M416 Alpiflow Column Flowmeter P.019 ALPI-VAC vaccum regulator P.020 Alpi-vent suction units P.021 ACCESSORIES P.022 Respiratory therapy accessories P.022 Suction accessories P ISO QUALITY ASSURANCE All Rotarex regulators are produced in Europe in accordance with international standards (ISO; CGA...) and are guaranteed to provide safe and reliable performance in operation. All locations are ISO

4 4 INTRODUCTION CEODEUX MEDITEC SOLUTIONS Patient therapy and safety is our main focus in the design, installation, commissioning and operation of medical gas equipment QUANTITY OF SUPPLY Regulators are designed in such a way sufficient medical gas capacity can be ensured in order to provide the required pressures and flows of gases for the intended number of patients to be treated at any time. IDENTITY OF SUPPLY All our products are designed, produced and controlled for a specific medical gas. All points to which the user or technical staff can connect are gas specified. There is no risk of misconnection. QUALITY OF SUPPLY Our regulators maintain quality of supplied medical gases thanks to appropriate selection of material, components cleanliness and internal filtration equipment. Products designs ensure safe supply by minimizing ignition risks, by avoiding patient poisoning risks and by guaranteeing very good performances for accurate therapies. QUALITY FIRST... CEODEUX MEDITEC products are designed, validated, produced and controlled during their whole lifetime according to a very stringent quality system which exceeds requirements of ISO standard. DESIGN All our products comply with local and international standards. Some reference standards: CGA E-7 Medical gas pressure regulators Flowmeters and orifice flow selectors Products design and validation ISO Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices ISO Flowmeters for use with medical gases Materials selection and cleanliness ISO 15001:2011 Anesthetic and respiratory equipment. - Compatibility with oxygen Product design is done through a risk assessment process and is combining proven technologies and innovation to reach the best performance levels. VALIDATION Product validation process guarantees that products are developed and produced to withstand the complete lifecycle (installation, commissioning, normal service and maintenance) PRODUCTION All products are produced in a controlled environment in order to maintain cleanliness An individual traceability is ensured with individual serial number Products are individually controlled and data are recorded for a perfect product management. All products are cleaned according to ISO 15001

5 INTRODUCTION 5 THE MAIN MEDICAL GASES Symbol Name Application Source Type O 2 Air N 2 O CO 2 Air N 2 Oxygen Air Nitrous Oxide Carbon Dioxide Surgical Air Nitrogen Oxygen is one of the most extensively used gases for respiratory therapy and life-support and is additionally used in anesthetic procedures. Medical air is mainly used in respiratory therapy as a power source for patient ventilators, and for blending with oxygen. It is also used as the driving gas for nebulized drugs and chemotherapy agents. Nitrous oxide is used for anesthetic and analgesic purposes, being mixed with air, oxygen, and nebulized agents. Carbon dioxide is used less commonly now as a respiratory stimulant, and for insufflation during surgery. Surgical air (of medical air quality) is also used, at a higher pressure, to power a variety of surgical tools and other devices such as tourniquets. As an alternative, nitrogen can be used for the same purpose as surgical air. Compressed gas cylinder Liquid tank Concentrator Compressor Compressed gas cylinder Liquefied gas cylinder Liquefied gas cylinder Compressor Compressed gas cylinder Compressed gas cylinder

6 6 PRODUCT RANGE OVERVIEW PRESSURE REGULATORS STANDARD RESPIRATORY THERAPIES ALPINOX ALPINOX MEDICAL OXYGEN P. 08 REGULATOR WITH FLOW SELECTOR ALPINOX MEDICAL OXYGEN P. 08 REGULATOR WITH QUICK CONNECTOR ALPINOX PIN INDEX MEDICAL P. 08 OXYGEN REGULATOR WITH FLOW SELECTOR MINIOX MINIOX QUICK CONNECTOR P. 10 MINIOX COLUMN FLOWMETER P. 10 PRESSURE REGULATORS SPECIAL THERAPIES (ASSISTED) BSC 280/380 P. 12 SINGLE STAGE CARTRIDGE REGULATOR BSC 290/390 P. 14 SINGLE STAGE CARTRIDGE REGULATOR WITH HOSE BARB DI 235 P. 16 NITRIC OXIDE APPLICATIONS DOUBLE STAGE BELLOW REGULATOR

7 PRODUCT RANGE OVERVIEW 7 IN HOSPITAL THERAPY EQUIPMENT FLOW METERING DEVICES ALPI-FLOW FLOWMETER WITH CALIBRATED ORIFICES P. 18 COLUMN FLOWMETER P. 19 SUCTION EQUIPMENT ALPI-VAC VACCUM REGULATOR P. 20 ALPI-VENT SUCTION UNITS P. 21 ACCESORIES RESPIRATOTY THERAPY ACCESSORIES REMOVABLE HOSE BARB P. 22 HUMIDIFIER P. 22 ALPI-CLICK P. 22 MEDICAL PROBES MEDICAL CONNECTORS (SINGLE AND DOUBLE) SUCTION ACCESSORIES SMALL COLLECTION JAR P. 23 LARGE COLLECTION CONTAINERS P. 23 OUTLET HOSE CONNECTION P. 23

8 8 ALPINOX ALPINOX MEDICAL OXYGEN REGULATOR Cylinder regulator for hospital and home care oxygen therapy A new generation of medical regulator with high flow precision and continuous flow between settings. In compliance with EN ISO KEY FEATURES Single stage piston regulator ensuring high life cycle Preset integrated pressure relief valve Flowmeter with stop at 0 Easy to clean High precision flow from 0.25 lpm to 25 lpm Continuous flow from 0 to maximal flow Integrated safety relief device protected and none accessible Ergonomic handwheel and modern design. Red dot design award Easily cleanable Rubber protection on the gauge Plastic protection on the regulator Ergonomic plastic hand-wheel on the inlet connection Position 25 lpm intended for the nebulization 20μm Filter inside the seat regulator Design free of fluorinated polymers whose combustion products are toxic Individual number for traceability OPTIONS Lateral marking STANDARD ALPINOX ALPINOX WITH QUICK CONNECTOR ALPINOX PIN INDEX KEY ADVANTAGES DESIGN BENEFITS Improved external benefits Protective external plastic shell Possibilty of plastic replacement in case of external damages Homogenous, aesthetic and easily cleanable for healthcare environments Fixed reading window, all important parameters directly accessible and visible at first glance Possibility to have a digital gauge for easier control (compatible with all cylinder sizes) Ergonomic flow knob for a proper flow selection QUALITY & RELIABILITY 10 years lifetime Reduction of cost ownership with no preventive maintenance Risks reduction and improvement of product management thanks to the traceability PERFORMANCE & SAFETY Strong medical oxygen comptability Design free of Aluminium and Stainless Steel O-ring exclusively made of EPDM (no viton / no Nitrile)* Seat PA6.6 (no PCTFE)* No surface treatment on gas wetter areas Flow selector with 12 positions and continuous flow More exact flow that fits to the patient s need Possible flow adjustement during therapy without Oxygen supply interruption Flow accurate for precise patient oxygen therapy No magnetic component content MRI compatible

9 ALPINOX 9 SPECIFICATIONS Gas Medical oxygen, Air Flow range From 0-2 Lpm to 0-25 Lpm Seat material Nylon Max Inlet pressure Gauge Filter 200 bar bar, psig 20 micron, sintered bronze Body material O-ring material Brass EPDM Regulatory status CE marking Complies with medical devices directive 93/42/EEC and EN ISO CE0476 DIMENSIONS FLOW RANGE Flow Range (Lpm) Pos 1 Pos 2 Pos 3 Pos 4 Pos 5 Pos 6 Pos 7 Pos 8 Pos 9 Pos 10 Pos 11 Pos /4 1/2 3/ / / / /4 1/ PRODUCT CONFIGURATOR Gas Working Pressure Cylinder Connection Outlet Pressure Flow Range Pressure outlet Flow outlet M730 O2 200 NF 4.5 2L N HB6 O 2 O2 200 bar 200 AFNOR NF 3.5 bar Lpm 2L None N Hose Barb Ø6mm - Fixed Air AIR 2000 psig 2000 DIN D 4.5 bar Lpm 6L AFNOR NF Hose Barb Ø6mm - Removable 9/16 N 2 O/O 2 N2O 3000 psig 3000 BS B 0-15Lpm 15L DIN DIN Hose Barb Ø6mm - Removable M12x125 UNI U 0-25Lpm 25L BS BS Hose Barb Ø6mm - Removable G1/4 Pin-Index P SS SS HB6 9/16 M12 1/4

10 10 MINIOX MINIOX MEDICAL OXYGEN REGULATOR Medical pressure regulator for hospital and homecare respiratory therapy. Used to reduce cylinder pressure to a lower pressure suitable for medical equipment and/or for gas delivery direct to patient. KEY FEATURES Safety first Smart choice of materials in conformance with ISO and the most restrictive additional requirements Design free of fluorinated polymers Fitted with a safety relief valve in case of over pressure Even in case of failure, no high pressure exposure High performances Better outlet pressure and flow stability Inverted seat regulator for a longer lifetime Design resistant to pressure shocks & adiabatic compression Lower operating costs Compact and lightweight design for an easy handling and storage Suitable for all types of medical gases Precise flow and improved stability for better gas consumption management REGULATORY ISO CGA E-7 MINIOX WITH QUICK CONNECTOR MINIOX WITH COLUMN FLOWMETER

11 MINIOX 11 SPECIFICATIONS Gas O 2 / Air / N 2 O Diaphragm EPDM Max. Flow rate 40 Lpm Max. Inlet Pressure 200 bar O-rings EPDM Weight 0,640 kg Gauge Temperature range Body material bar -20 C to +60 C Chrome plated brass Seat PA 6.6 Filter Outlet pressure 20 μm sintered bronze 3.5 bar/4.5 bar Inlet Connection Outlet Connection According to national standards According to national standards PRODUCT DESCRIPTION COLUMN FLOWMETER 0-15 Lpm HIGH PRESSURE GAUGE Cylinder content visual indication 3 INTEGRATED SAFETY RELIEF VALVE Protect regulator against overpressure risks CYLINDER VALVE CONNECTION According to national standards PRESSURE REGULATOR Diaphragm technology PRODUCT CONFIGURATOR Quick connector version Gas Inlet pressure Outlet pressure Outlet types Inlet connection Outlet dimensions M743QC O ,5 SQC DIN DIN Oxygen O bar 200 4,5 bar 4,5 Single quick connector SQC G1/4 Female O2 DIN DIN 3,5 bar 3,5 Dual quick connector DQC NF NF AFNOR NF S AF DIN DIN SS SS BS BS NEN 3268 NEN UNI UNI CGA V1 CGA Pin Index PI Flowmeter version Gas Inlet pressure Outlet pressure Inlet connection Outlet dimensions Flow rate M743 O ,5 DIN G1/4 15 Oxygen O2 200 bar 200 4,5 bar 4,5 G1/4 Female O2 G1/4 G1/ Lpm Air AIR 2000 psig ,5 bar 3,5 NF NF M12x125 M Lpm DIN DIN 9/16 UNF 9/16 BS BS NEN 3268 NEN UNI UNI CGA V1 CGA Pin Index PI

12 12 HIGH PRESSURE REGULATOR SERIES BSC 280/380 SINGLE STAGE CARTRIDGE REGULATOR Enables gas supply to therapy machines Especially designed for accurate NO mixtures therapies Can be fitted with pressure sensor for proper therapies parameters management 6 ports for multiple possible configurations and appropriate product integration thanks to compactness INCLUDED FUNCTIONS Inlet port Outlet port Pressure regulator Safety relief valve High pressure measurement Low pressure measurement REGULATORY Medical certified according to MDD 93/42/EEC amended 2007/47/EC Product complies with EN ISO KEY ADVANTAGES SAFETY FIRST Fitted with a safety relief valve in case of over pressure which can be collected Dedicated HP and LP pressure gauges for a permanent indication Compatible materials with Oxygen and medical applications No gas contamination due to a metal-metal sealing HIGH PERFORMANCE Proven Cartridge Seat Technology Better outlet pressure and flow stability Smart choice of material in conformance with EN ISO LOWER OPERATING COSTS Compact and lightweight design for an easy handling and storage Longer product life thanks to less impingement on the diaphragm Easy maintenance operations thanks to Cartridge Technology Right inlet Plugged Pressure gauges Inlet (HP) Outlet (LP) Safety valve Plugged Left inlet

13 HIGH PRESSURE REGULATOR 13 SPECIFICATIONS Body Seat seal O-ring Chrome plated brass Polyamide EPDM Inlet Connection Outlet Connection Leak rate Cylinder connection Hose Barb or Medical connector 10-8 mbar l/s He Inlet pressure Outlet pressure 200 / 300 bar 2900 / 4350 psig 4 / 8 bar 58 / 116 psig Nominal Flow 7 / 25 Nm 3 /h (N 2 ) Diaphragm Hastelloy Weight ± 1.4 kg Temperature range -40 C to +60 C PRODUCT CONFIGURATOR Material Inlet Pressure Port Configuration Outlet pressure Inlet Connection Outlet connection Pressure Sensor Gas BSC I 280 R 5 DIN NIST B NO Stainless I 200 bar 280 Right inlet R 5 bar 5 DIN477-1 DIN G1/4 F G14F without pressure A steel sensor NO (max 1000ppm)/N2 Left inlet L ISO5145 ISO 1/4 NPT F N14F with HP pressure B sensors CGA V1 CGA with LP pressure C sensor with HP & LP D pressure sensors NO

14 14 HIGH PRESSURE REGULATOR SERIES BSC 290/390 HP CYLINDER PRESSURE REGULATOR Enables gas supply to therapy machines Can be fitted with pressure sensor for proper therapies parameters management 6 ports bodies for multiple possible configurations and appropriate product integration INCLUDED FUNCTIONS Inlet port Outlet port Pressure regulator Safety relief valve High pressure measurement Low pressure measurement REGULATORY Medical certified according to MDD 93/42/EEC amended 2007/47/EC Product complies with EN ISO KEY ADVANTAGES SAFETY FIRST Fitted with a safety relief valve in case of over pressure which can be collected Dedicated HP and LP pressure gauges for a permanent indication Compatible materials with Oxygen and medical applications No gas contamination due to a metal-metal sealing HIGH PERFORMANCE Proven Cartridge Seat Technology Better outlet pressure and flow stability Smart choice of material in conformance with EN ISO LOWER OPERATING COSTS Compact and lightweight design for an easy handling and storage Longer product life thanks to less impingement on the diaphragm Easy maintenance operations thanks to Cartridge Technology Right inlet Plugged Pressure gauges Inlet (HP) Outlet (LP) Safety valve Plugged Left inlet

15 HIGH PRESSURE REGULATOR 15 SPECIFICATIONS Body Seat seal O-ring Chrome plated brass Polyamide EPDM Inlet Connection Outlet Connection Leak rate Cylinder connection Hose barb or medical connector 10-8 mbar l/s He Inlet pressure Outlet pressure 200 / 300 bar 2900 / 4350 psig 4 / 8 bar 58 / 116 psig Nominal Flow 7 / 25 Nm 3 /h (N 2 ) Diaphragm Hastelloy Weight ± 1.4 kg Temperature range -40 C to +60 C PRODUCT CONFIGURATOR Material Inlet Pressure Port Configuration Outlet pressure Inlet Connection Outlet connection Pressure sensor Gas Type BSC L 290 R 4 NF NIST B O2 Chrome plated L 200 bar 290 Right inlet R 4 bar 4 G1/4 Female O2 Hose Barb HB without pressure A O2 O2 brass 2900 psig 58 psig 6 mm sensor 300 bar 390 Left inlet L 8 bar 8 NF NF AFNOR Medical NF with HP pressure B Air AIR 4350 psig 116 psig Connector sensors 10 bar 10 DIN DIN DIN Medical DIN with LP pressure C N2O N2O 145 psig Connector sensor BS BS NIST Medical NIST with HP & LP D CO2 CO2 Connector pressure sensors NEN 3268 NEN N2 N2 UNI CGA V1 UNI CGA

16 16 PRESSURE REGULATORS SPECIAL THERAPIES (ASSISTED) SERIES DI 235 NITRIC OXIDE DOUBLE STAGE BELLOW REGULATOR For NO/N 2 mixtures Diaphragm/bellow dual stage Purity up to 6.0 Max inlet pressure: 300 bar (4350 psig) Preset outlet pressure: 2,5/5 bar (36/72 psig) Compact and lightweight design 1 inlet / 2 outlets Inlet/outlet pressure gauges 2 safety relief valves Special requirements on request APPLICATIONS Designed for cylinder regulator applications. Ideally suited for special NO/N 2 mixtures (N 2 with 1000 ppm NO) applications requiring a very stable outlet pressure together with a very sensitive set up of this outlet pressure. KEY FEATURES The DI 235 regulator is based on the S 20 proven bellow technology. Accurate pressure control for reliable service and guarantees a stable outlet pressure due to the combination of the diaphragm and bellow technology. Compact and lightweight design. Can also be equipped with a needle or shut off valve at the outlet.

17 PRESSURE REGULATORS SPECIAL THERAPIES (ASSISTED) 17 SPECIFICATIONS Female ports Seat seal O-ring Diaphragm Bellow 16 x (inlet) - G 3/8 (outlet) or 1/4 NPT (inlet/outlet) PTFE (1 st stage) EPDM (2 nd stage) FPM Hastelloy AISI 316L (SS version) Weight Leak rate ± 1,4 kg ± 3.0 lbs 10-8 mbar l/s He Temperature range - 20 C to + 60 C - 4 F to F Gauges High and low pressure (M10 x 1 or 1/4 NPT) Max inlet pressure Outlet pressure 300 bar 4350 psig 2,5/5 bar 36/72 psig Nominal Flow 1,8/3 Nm 3 /h (N 2 ) FLOW CURVES DI pdf 1 26/11/12 11:35 PRESSURE bar 6,0 FLOW CURVE DI 235 REGULATOR SET: 5 bar / 72.5 psig 2.5 bar / psig PRESSURE psig 116 OUTLET PRESSURE- bar and psig OUTLET PRESSURE-Bar and Psi 5,0 4,0 3,0 2,0 1,0 0,0 Blue line P1 = 300 bar Red line P1 = 150 bar Green line P1 = 75 bar 0 Nm 0 /h Nlpm Slpm 18 35FLOW RATE-Nm3/h 53 (LPM) en azote (N2) 70 ) SCFM FLOW RATE in Nitrogen (N 2) 101, , , ,5 PRODUCT CONFIGURATIONS Body Material Outlet Pressure End Connections Gauges D I G 1 Stainless steel I 2,5 bar 2,5 In: 16 x G Without 0 36 psig Out: G 3/8 5 bar 5 1/4 NPT - 1/4 NPT N With 1 72 psig

18 18 IN-HOSPITAL THERAPY EQUIPMENT M730 ALPINOX FLOWMETER WITH CALIBRATED ORIFICES Flow-meter for hospital and ambulance oxygen therapy New generation of medical flow-meter with high flow precision and continuous flow between settings. The flow-meter is in compliance with the EN ISO TO BE MOUNTED ON A RAIL WITH FLEX HOSE (ACC. TO EN ISO 5359) KEY FEATURES Continuous flow between settings Stop at 0 Inlet pressure : 4 bar 0/+1 bar Flow precision acc. EN ISO Flow range: 0-15 lpm (12 positions) NEW GENERATION ALPINOX FLOWMETER MEDICAL FLOWMETER High flow precision from 0.1 lpm to 25 lpm Continuous flow from 0 to maximal flow Ergonomic and modern design Easily cleanable Plastic protection on the flowmeter Position 25 lpm intended for the nebulization Swiveling design 360 for optimal readability Design free of fluorinated polymers whose combustion products are toxic TO BE CONNECTED ON CEODEUX MEDITEC TERMINAL UNITS 360 SPECIFICATIONS Inlet Connection Flow Outlet Dimensions Weight Medical connector acc. to national standards M12x1.25 M.-9/16 UNF M. -G1/4 M. 136x33x82mm Kg Inlet pressure Temperature range Flow Range Accuracy 6 bar max -20 C to +60 C 0-15 Lpm ± 10 % read value or ± 0.5 Lpm if greater Body O-ring Measuring tube Chrome plated EPDM Polycarbonate PRODUCT CONFIGURATOR Gas Inlet Pressure Flow range Inlet Connection Flow outlet M730-FM O L NF 9/16 O 2 O2 3.5 bar Lpm 2L AFNOR NF Hose Barb Ø6mm - 9/16 Removable 9/16 Air AIR 4.5 bar Lpm 6L DIN DIN Hose Barb Ø6mm - NF Removable N 2 O N2O 0-15Lpm 15L BS BS M12x125 M Lpm 25L SS SS Hose Barb Ø6mm - Removable G1/4 1/4

19 IN-HOSPITAL THERAPY EQUIPMENT 19 M416 ALPIFLOW COLUMN FLOWMETER Medical Column Flowmeter for Oxygen and others medical gases (Air, N 2, CO 2, N 2 O) Combination of a precise needle valve and an accurate measuring device for a proper dosage of medical gases TO BE MOUNTED ON A RAIL WITH FLEX HOSE (ACC. TO EN ISO 5359) KEY FEATURES Swiveling design 360 for an optimal orientation Gas specific marking and color Available in twin units versions for two independent suppliers from one single source. REGULATORY Medical CE certified according to MDD 93/42/EEC amended 2007/47/EC Product complies with EN ISO TO BE CONNECTED ON CEODEUX MEDITEC TERMINAL UNITS SPECIFICATIONS Gas O 2 and medical air Working pressure 4,5 bar ± 0,5 (65,3 psig ± 7) Testing pressure 10 bar (145 psig) Flow range 0-1,5 Lpm / 0-5 Lpm 0-15 Lpm / 0-30 Lpm Working temperature Calibration temperature -20 To + 60 (-4 F to 140 F) 23 C ± 2 Flow accuracy ± 10% of indicated value or ± 0,5 Lpm Tightness int / ext 8, mbar.l.s -1 Inlet connections G1/4"M - NF S Air & O 2 DIN Air & O 2 - BS 5682 Outet connections Hose barb EN DN 6 - M12x1,25-9/16" - 18UNF.M (CGA 1240) - G1/4"M (ISO 3253) Operating torque < 1Nm at working pressure Dimensions Body Gas wetted materials Height : ~150mm Width : ~73mm Diameter : 035,5mm Weight : ~200g Raw brass Raw brass, PC, pom, EPDM PRODUCT CONFIGURATOR Gas Type Flow range Inlet Connection Inlet Type Outlet Connection M416 O2 1.5 G14 D M12 Oxygen O2 1.5 Lpm 1.5 G1/4M G14 Direct D M12x125 M12 Air AIR 5 Lpm 5 AFNOR NF Indirect - 1,5m " - 18UNF 9/16 flexible hose 15 Lpm 15 DIN DIN Indirect - 3,0m 3.0 G1/4M G14 flexible hose 30 Lpm 30 BS BS Hose barb 6mm HB6

20 20 SUNCTION EQUIPMENT ALPI-VAC VACCUM REGULATOR Medical vaccum regulator ( VAC) Regulator suitable for all medical suction applications in hospitals and nursing homes Insure safe, quick and reliable use thanks to performant technology and easy manipulation KEY FEATURES The ALPI-VAC continuous suction vacuum regulator is particularly suitable for all medical suction applications in hospitals and nursing homes. The device is made of a strong techno-polymer body, with a quick I/0 switch-button, a suction adjustment knob and a control vacuum gauge with three possible end-of-scale choices: -250 mbar, -600 mbar and mbar. A protective silicone cover prevents gauge damages caused by possible shocks received during transport or use. The ALPI-VAC vacuum regulators are also designed, through a threaded connection, for connecting directly or indirectly to the normal collection containers for suctioned fluids. The extreme rationality and simplicity, combined with the sophisticated technical execution, allow both operators and patients to appreciate the safety and reliability of this medical device. SPECIFICATIONS Sizes (LxWxH) Weight Maximum suction rate 103x92x170 mm ALPI-VAC 250: 0.42 Kg ALPI-VAC 600/1000: 0.37 Kg ALPI-VAC 250: 50 L/min. ±5 L/min. at -220 mbar ALPI-VAC 600: 72 L/min. ±5 L/min. at -550 mbar ALPI-VAC 1000: 115 L/min. ±5 L/ min. at -950 mbar Maximum adjustable depression Valve protecting against excessive negative pressures ALPI-VAC 250: -220 mbar ±20 mbar ALPI-VAC 600: -550 mbar ±20 mbar ALPI-VAC 1000: -950 mbar ALPI-VAC 250/600: preset with anti-clogging system ALPI-VAC 1000: N/A Maximum supply depression Suction adjusting system Standard vacuum supply connection Outlet connection -950 mbar With membrane ISO G. 1/4 M ISO G. 1/2 M I/0 switch Quick push button type

21 SUNCTION EQUIPMENT 21 ALPI-VENT SUCTION UNITS Vaccum generating system unit (VAC) Up to 850 mbar Suitable for all hospital applications where a central facility of vacuum generation for suction is missing KEY FEATURES The ALPI-VENT/500 and ALPI-VENT/1000 vacuum generating system units are particularly suitable in all hospital applications in which it is necessary to get values of vacuum up to -850 mbar and where a central facility of vacuum generation for suction is missing, often for technical choice. As it is well known, the physical principle called Venturi allows to get depression from a fluid under pressure, which is obtained, in case of these devices, using medical compressed air coming from the centralized distribution plant. Such devices are composed essentially of a brass chrome-plated body, a needle valve with vacuum adjustment knob and a vacuum gauge. The version ALPI-VENT/1000 fits also a quick I/0 button switch and a large gauge, while in the version ALPI-VENT/500 a protective silicone cover on vacuum gauge avoids damages caused by possible impacts during transport or use. ALPI-VENT/1000 ALPI-VENT/500 SPECIFICATIONS Sizes (without collection jar) (LxWxH) Weight (without collection jar) Max. suction range ALPI-VENT/500: 88x70x92 mm ALPI-VENT/1000: 140x80x140 mm ALPI-VENT/500: 0.80 Kg ALPI-VENT/1000: 0.95 Kg ALPI-VENT/500: 25 L/min. ±2 L/min. ALPI-VENT/1000: 27 L/min. ±2 L/min. Vacuum gauge scale ALPI-VENT/500: mbar ALPI-VENT/1000: 0-1 bar Suction range ALPI-VENT/500: -800 mbar ±25 mbar ALPI-VENT/1000: -850 mbar ±25 mbar Standard supply pressure bar Adjustment of suction level needle valve Air consumption 47 L/min. ±2 L/min. at the max. suction value Inlet connection ISO G. 1/4 M. Outlet connection to the patient ISO G. 1/2 M.

22 22 ACCESORIES RESPIRATORY THERAPY ACCESSORIES REMOVABLE HOSE BARB Devices used to connect or disconnect specific medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies. Designed according to EN for ø 6mm tube. SPECIFICATIONS Thread M12x125 G1/4 9/16 UNF Materials Brass chrome plated CE marking CE 0476 HUMIDIFIER Used to connect or disconnect specific medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies. Designed and approved in accordance with the EN ISO SPECIFICATIONS Inner volume Sizes (LxWxH) CH/200: 210 ml TR/200: 120 ml MAK/300: 285 ml MAK/500: 355 ml CH/200: 55x67x200 mm TR/200: 60x75x190 mm MAK/300: 70x81x175 mm MAK/500: 70x81x207 mm Weight Applicable pressure and flow CH/200: 0.11 Kg TR/200: 0.13 Kg MAK/300: 0.15 Kg MAK/500: 0.16 Kg Pressure: 500 kpa Flow: 10 L/min. Inlet connection Outlet connection 1/4 ISO 3253 F 3/8 ISO 3253 F M 12x1.25 F 9/16 UNF F Hose connector Ø 6 9 mm ALPI-CLICK MEDICAL PROBES MEDICAL CONNECTORS (SINGLE AND DOUBLE) Used to connect or disconnect two specific medical devices for anesthesia, ventilation, oxygen therapy or various medical therapies. Designed and approved in accordance with the following standards: NF S , DIN , SS , EN ADVANTAGES Swiveling design 360 for optimal use. Design free of fluorinated polymers whose combustion products are toxic. SPECIFICATIONS Gas Oxygen, Air, 50% N 2 0 / 50% 0 2 Materials Brass chrome plated, EPDM, Nylon CE marking CE 0476

23 ACCESORIES 23 SUCTION ACCESSORIES SMALL COLLECTION JAR Small collection jar are used for suction of small volume of fluids and have been designed and manufactured for applications of high flow and high vacuum Can also be use as a safety container to protect the equipment and the plant upstream of the section source Matched with ALPI-VAC vacuum regulators ADVANTAGES The two models have capacities of 300 ml and 500 ml respectively in standard execution, or fitting a special lid for housing an antibacterial filter. The jar and the lid are made in polycarbonate, with fittings in brass, with ergonomic screw nut in high-strength polycarbonate. All parts can be sterilized in an autoclave (121 C - 15 min.) Inner volume Sizes (LxWxH) MAK/300/300 a.b: 300 ml MAK/500/500 a.b: 500 ml MAK/300: 70x98x180 mm MAK/300 a.b: 70x98x210 mm MAK/500: 70x98x215 mm MAK/500 a.b: 70x98x245 mm Weight MAK/300: 0.20 Kg MAK/300 a.b: 0.24 Kg MAK/500: 0.21 Kg MAK/500 a.b: 0.25 Kg Supply max -950 mbar - 5 min depression Overflow valve Inlet connection Outlet connection Antibacteria system also available for both model (see specification table: a.b) Floating valve ISO G 1/2 F. Hose connector Ø mm LARGE COLLECTION CONTAINERS Large collection container for suctioned liquid for applications of high flow and high vaccum Can also be use as a safety container to protect the equipment and the plant upstream of the section source Matched with ALPI-VAC vacuum regulators ADVANTAGES These devices are available with a capacity of 1000 ml with screw cap, of 2000 ml with screw and pressure lid and 4000 ml with pressure lid. The jar and the lid are made in polycarbonate, with fittings in brass, with ergonomic screw nut in highstrength polycarbonate. All parts can be sterilized in an autoclave (121 C - 15 min.). Inner volume Sizes (LxWxH) MAK/1000: 1000 ml MAK/2000 with screw lid: 2000 ml MAK/2000 with pressure lid: 2000 ml MAK/4000: 4000 ml MAK/1000: 110x110x243 mm MAK/2000 with screw lid/ with pressure lid: 140x140x298 mm MAK/4000: 175x175x310 mm Weight Supply depr. Overflow valve MAK/1000: 0.38 Kg MAK/2000 with screw lid: 0.49 Kg MAK/2000 with pressure lid: 0.49 Kg MAK/4000: 0.99 Kg max -950 mbar- 5 min Floating valve Inlet connection Outlet connection Hose connector Ø mm or ISO G 1/2 F (for MAK/1000 and MAK/2000 screw lid only) Hose connector Ø mm OUTLET HOSE CONNECTION Vacuum regulator outlet hose connection Use to connect ALPI-VAC (Vaccum regulator) and its equipment MAK (collection container) ADVANTAGES Connector for hose Ø 7.5 mm, ISO G. 1/2 F. inlet thread.

24 24 NOTES

25 25 NOTES

26 A FULL LINE OF GAS CONTROL SOLUTIONS COMPLETE SOLUTIONS FROM SOURCE TO PROCESS. ROTAREX is helping engineers worldwide to get better gas results: from ultra high purity production and medical care facilities to industrial and LPG applications, as well as alternative energy vehicles, fire suppression, diving, aerospace, cryogenics, laboratory, petro-chemical and welding. ROTAREX applies over 90 years of know-how and experience to custom design, develop and manufacture the high performance valves, regulators and fittings to suit your needs, all in one hand. Discover the difference ROTAREX can make in your world. CYLINDER VALVES EQUIPMENT FIRETEC AUTOMOTIVE LPG/SRG MEDITEC

27 ULTRA HIGH PURITY VALVES MEDICAL VALVES & EQUIPMENT INDUSTRIAL CYLINDER VALVES REFRIGERANT CYLINDER VALVES PRESSURE REGULATORS SUPPLY & SWITCH OVER BOARDS LINE VALVES FITTINGS & ADAPTORS FIXED INSTALLATION FIRE SYSTEMS OBJECT FIRE SUPPRESSION SYSTEMS AUTOMOTIVE VALVES & REGULATORS WATER CARBONATION LPG TANK VALVES & REGULATORS LPG CYLINDER VALVES & REGULATORS DIGITAL MEASUREMENT SYSTEMS PLASTIC INJECTION MOULDING AUSTRALIA / BRASIL / CHINA / FRANCE / INDIA / ITALY / JAPAN / LUXEMBOURG / MIDDLE EAST / RUSSIA / SINGAPORE / SPAIN / THAILAND / USA AUSTRALIA / BRASIL / CHINA / FRANCE / INDIA / ITALY / JAPAN / LUXEMBOURG / MIDDLE EAST / RUSSIA / SINGAPORE / SPAIN / THAILAND / USA

28 WORLDWIDE HEADQUARTERS ROTAREX S.A. 24, rue de Diekirch, L-7440 Lintgen Luxembourg Tel.: Fax: ceodeuxmeditec@rotarex.com REGIONAL / COUNTRY HEAD QUARTERS NORTH AMERICA EUROPE ASIA - PACIFIC MIDDLE EAST / AFRICA USA Rotarex North America 101 Bilby Road Building 2 Hackettstown, NJ USA Tel.: northamerica@rotarex.com SOUTH AMERICA BRASIL Rotarex Brazil Ltda Cond. Ind. Portal da Anhanguera Estr. Municipal Gov. Mário Covas, S/N Bairro Macuco -Valinhos São Paulo Brazil Tel.: Fax: brasil@rotarex.com EUROPEAN HEADQUARTERS 24, rue de Diekirch, L-7440 Lintgen, Luxembourg Tel.: ceodeuxmeditec@rotarex.com ITALY Rotarex Italia S.r.l. 46 Via Giacomo Matteotti I-25080, Ciliverghe di Mazzano (BS) Italy Tel.: Fax: italia@rotarex.com SPAIN Rotarex Spain Edificio Foro de Somosaguas Ctra. Carabanchel a Pozuelo, km. 5,6 Urb. Pinar de Somosaguas, 89 bis Planta 1, Oficina Pozuelo de Alarcón Spain Tel.: spain@rotarex.com RUSSIA Rotarex Rus Tverskaya street, 20/1 bldg. 1 of , Moscow Russia Tel.: Skype: rotarexrus russia@rotarex.com ASIA-PACIFIC HEADQUARTERS Rotarex Fareast Pte Ltd 10 Ubi Crescent Ubi Techpark, Lobby C, # Singapore Tel.: Fax: fareast@rotarex.com CHINA Rotarex Star 60 Yuan Zhong Road Shanghai Nanhui Industrial Zone , Shanghai China Tel.: Fax: china@rotarex.com JAPAN Rotarex Japan Ltd 6F, Yawaragi Bldg., Taito Taito-ku, Tokyo JAPAN Tel.: Mob.: Fax: japan@rotarex.com INDIA Rotarex ENGG. PVT. LTD. C-105, Mahindra Apartments Vikaspuri, New Delhi mob.: india@rotarex.com THAILAND Rotarex (Thailand) Co Ltd. 200, Moo 4 Jasmine International Tower, 6 Floor 607E Chaengwattana road, Pakkret, Pakkret, Nonthaburi Thailand Tel.: Fax: thailand@rotarex.com MIDDLE EAST Rotarex Middle East Jebel Ali Free Zone - Lob 17, Office 415 P.O. Box Dubai, U.A.E. Tel.: +971 (0) Fax: +971 (0) middle-east@rotarex.com POLAND Rotarex Polska 5 Gröbli PL Brzeg, Poland Tel.: Fax: polska@rotarex.com ROTAREX S.A. CEODEUX MEDITEC - CEODEUX S.A. MPR-EN-1116