REPAIR PARTS MANUAL. MODEL NO. LZ145H97RBK ( ) Lawn Tractor Rev. 1

Size: px

Start display at page:

Download "REPAIR PARTS MANUAL. MODEL NO. LZ145H97RBK ( ) Lawn Tractor Rev. 1"

Curtis Carter
5 years ago
Views:

1 MANUAL MODEL NO. LZ145H97RBK ( ) Lawn Tractor Rev. 1

2 HOW TO USE THIS MANUAL This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them. Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat. When ordering parts, always give the following information: Product - Tractor Model Number - LZ145H97RBK ( ) Part Number Part Description TABLE OF CONTENTS SCHEMATIC... 3 ELECTRICAL CHASSIS AND ENCLOSURES DRIVE...-9 STEERING ASSEMBLY SEAT...12 DECALS ENGINE MOWER BAGGER MOWER LIFT WARRANTY...BACK COVER 2

3 SCHEMATIC SCH0 12VDC AMMETER (OPTIONAL) BATTERY STARTER SOLENOID STARTER RED A RED FUSE RED M WHITE B S M G L A1 A2 CLUTCH / BRAKE (PEDAL UP) GREEN ATT'MENT CLUTCH (CLUTCH OFF) RED FBI BUZZER FBI SWITCH OPERATOR PRESENCE RELAY ORANGE RED 7A GRAY BLUE HOUR METER (OPTIONAL) NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. BLUE FUEL LINE GRAY CARBURETOR SOLENOID (IF EQUIPPED) RED RED SEAT SWITCH (NOT OCCUPIED) IGNITION UNIT CHARGING SYSTEM OUTPUT 3AMPDC@3600RPM GROUNDING CONNECTOR BAGGER INTERLOCK (NO BAG, CHUTE OR PLUG) SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES) 2 VOLTS AC 3600 RPM (CHARGING SYSTEM DISCONNECTED) ORANGE BROWN LIGHTING SYSTEM OUTPUT 5 AMP 3600 RPM DIODE STATOR 14 VOLTS AC 3600 RPM (LIGHTS OFF) LIGHT SWITCH HEADLIGHTS REVERSE SWITCH (NOT IN REVERSE) IGNITION SWITCH POSITION CIRCUIT MAKE OFF M+G+A1 RUN/OVERRIDE B+A1 RUN B+A1 L+A2 START B+S+A1 WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. 3 REMOVABLE CONNECTIONS NON-REMOVABLE CONNECTIONS 7 7A RELAY

4 ELECTRICAL C With Ammeter Option D.C. AMPERES Without Ammeter Option

5 ELECTRICAL Battery Bolt Hex Hd. 1/4-20 unc x 3/ Switch Interlock Harness Asm. Light w/4152j Bulb Light # Cable Starter 6 Ga. 11" Red Cable Battery CRD 56" Red Fuse Nut Keps Hex 1/4-20 unc Cable Ground 6 Ga. 1" Black Switch Seat Switch Ignition Key/Chain Switch Light/Reset B/B/Red Harness Ignition Bolt Flk. Fin. Hex 1/4-20 unc x 1/ Cover Terminal Red Solenoid Adapter Ammeter Rectangular Buzzer CRD Switch FBI CRD Screw Thdrol. 3/- x 1/2 Ty-Tt Socket Asm. Bulb Relay Asm Harness Pigtail Console ROS Screw Plastite x Module Reverse ROS NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. 5

6 CHASSIS AND ENCLOSURES chassis-crd_elite SV Pro_1.ai 6

7 CHASSIS AND ENCLOSURES Chassis Drawbar Screw 3/- x 3/ Bumper Hood/Dash Saddle Clip Insulator 13/32 Mtg. Hole Dash Bolt, Carriage 3/- x 3/ Panel, Dash, LH Panel, Asm. Dash RH Screw, Machine, Truss Head 5/-1 unc x 3/ Nut Hood Bumper Hood Bolt Washer 13/32 x 13/ x 12 Ga Nut Grille/Lens Asm Fender Bracket, Fender Support Footrest, LH Footrest, RH Bolt Screw Thdrol. 5/-1 x 1/2 TYT Bracket Asm. Pivot Mower Rear Bracket Pivot Duct Intake Screw Hx. Wsh. Hi-Lo 1/4-1/ Console CRD Auto Rod Pivot/Hood Bracket Exten. Chassis LH CRD Bracket Exten. Chassis RH CRD Support Battery CRD Cover Battery Backplate CRD Bolt Rdhd. Sqnk. 3/- x 2-1/2 Gr Washer 13/32 x 1-1/4 x Ga Nut, Keps Hex 3/- unc Door Trap Rod Pivot FBI CRD Bracket Actuator Bagger CRD Knob Rod Brake Parking Latch Asm. Mulch/Bagger Nut Weld Washer # Washer Lock # Screw Pan Hd. Phillip x 5/ Nut, Push Screw Thdrol. 3/- x 1/ Screw Thdrol. 5/-1 x 1/ Screw Thdrol. 3/- x 1/ Screw Hex Wsh. Thdrol. 3/ Cover Fender Rack Lens Grille Pro RH Lens Grille Pro LH Insert Grille Pro Bezel Grille RH Bezel Grille LH Seal RH Side Bagger Seal LH Side Bagger Screw #10 x Plug NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. 7

8 REPAIR PARTS DRIVE drive-crd_hydrogr_fender_1_r

9 DRIVE Transaxle Hydro Gear Rod, Shift Fender Clutch Asm. Noram Pin, Cotter 1/ x Washer, Lock Hvy. Helical Bolt Hex FGHD 5/-1 x Gr Nut Lock Hex w/ins. 5/-1 unc Nut Lock Hex w/ins. 3/- unc Knob Rod, Brake Nut Spring, Rod, Brake Pin, Cotter 1/ x 3/ Rod, Parking Brake Cap, Parking Brake Bracket, Mfg. Transaxle Shaft, Asm. Pedal Foot CRD Bearing, Nylon Washer 21/32 x 1 x Ga Pin, Roll 3/ x 1" Pulley Flat Composite 3.06" Bolt Fin. Hex 3/- unc x 2-3/ Spacer, Split 395 x 59 Bzp Washer 13/32 x 13/ x 12 Ga Washer 11/32 x 5/ x 12 Ga Pulley, Idler, V Groove Plastic Bellcrank Clutch Grnd. Drv Retainer, Belt Style Spring Bolt 3/- x 1-1/2 Gr Nut, Crownlock 3/- unc Nut Crownlock 5/ Link, Clutch Spring, Return, Clutch Screw 3/- x 1-1/ V-Belt Kev 112" 0650 CRD Cover, Pedal Washer Keeper, Belt Engine F-Proof Strap, Torque, LH Strap, Torque, RH Spacer, Split Washer 25/32 x 1-1/4 x Ga Ring, E Key, Square Washer 25/32 x 1-5/ x Ga Asm, Shaft, Cross Rear Spring, Torsion Washer 17/32 x 3/4 x Ga Link, Transaxle Control Asm. Bypass Hydro Spring, Retainer Washer 9/32 x 3/4 x 10 Ga Nut Lock Flg. 3/- unc Bushing, Bellcrank Grnd. Dr Washer 13/32 x 2 x 10 Ga Washer Srrted. 5/ ID x Bracket Shift Mount Hub Shift Bolt Rdhd. Sqnk. 1/4-20 x 3/4 Gr Nut Crownlock 1/4-20 unc Bolt Hex Fin. 1/4-20 unc x 1 Gr Bracket Pivot Lever Screw 5/-1 x 5/ Bracket Support Shift CRD Bolt Shoulder 5/-1 x Plate Fastening Lt Screw Thdrol. 3/- x 1/2 Ty-Tt Shaft Asm. Shifter Frt. CRD Keeper Flat Idler 3.06" CRD Bracket Idler Ground Drive CRD Keeper Belt 2.5" OD V-Idler CRD Pulley V-Idler CRD Link Shift Hub Tapered Round CRD Screw Thdrol. 5/-1 x Nyliner Snap-In 5/ Bolt Shoulder 5/-1 unc Bolt Rdhd. Sqnk. 5/-1 x Bolt Hex 7/-20 x Washer Nylon Rear Shaft Asm. Brake Rod Brake Hydro Washer 13/32 x 1 x Ga Bracket Cable Chassis Screw 3/- x Brace Shaft Brake Mtg Clip Retainer Bracket Pulley Pulley Idler Bolt Rdhd. 3/- unc x 2-3/4 Gr Screw 3/- x 3/ Bracket Idler Spacer Idler Chassis Shield Idler Mower Guard Muffler Washer 13/32 x 1 x 14 Ga Spacer Noram Bolt Rdhd. Sqnk. 3/- x 3-1/ Nut Jam Pulley Idler Composite Screw Hx wsh 3/- x 5/ NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 9

10 STEERING ASSEMBLY steering_pl.lt_60_r

11 STEERING ASSEMBLY Steering Wheel Front Axle Assembly Spindle Assembly, LH Spindle Assembly, RH Bearing, Race, Thrust, Hardened Washer 25/32 x 1-5/ x Ga Ring, Clip Link, Drag Washer, Lock Spacer Axle Nut Lock Flg 3/ Shaft Assembly, Steering Screw 3/- x 3/ Rod, Tie Washer 11/32 x 3/4 x Ga Washer Lock Hvy. Hlcl. Spr. 5/ Crownlock Nut 5/-24 unf Bushing, Steering Screw TT #I0-32 x 5 x 3/ Flange Cap Wheel Steering Washer 11/32 ID x 2-3/ OD x 12 Ga Nut Crownlock 3/ Adaptor, Steering Wheel Boot, Steering Dash P/L Mtl Washer 25/32 x 1-1/4 x Ga Extension Steering Cap, Spindle Spacer Axle Bolt Rdhd. Sq. 3/- x 2-1/ Brace Axle Steering Asm Bracket Susp. Chassis Front Washer Flat.71 x 1-1/2 x Bolt Shoulder 7/-20 unc Clip Steering Washer Hardened Bolt Fin Hx 5/-1 x 4 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm. 11

12 SEAT ASSEMBLY seat_lt.knob_ Seat Bracket Pnt. Pivot Fender Bolt Fin. Hex 3/- x Washer Flat 13/32 x 1 x 10 Ga Clip Push In Hinged Nut Lock Hex w/ins. 3/ Spring Seat Cprsn Blk. Zi Screw 3/- x Washer 13/32 x 1 x 14 Ga Pan Pnt. Seat (Blk.) Knob Seat Bracket Pnt. Mounting Switch Bushing Snap Blk. Nyl. 50 Id Bolt Rdhd. Sht. Nk. 1/4-20 x 1-1/ Spacer Split Spring Cprsn Nut Lock 1/4 Lge. Flg. Gr. 5 Zinc Bolt Shoulder 5/-1 unc-2a Nut Hex Lock w/ins. 5/ Washer 17/32 x 1-3/ x 12 Ga Bolt Shoulder 5/-1 x 62 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 12

13 MAX +_90N MAX +_150N REPAIR PARTS DECALS Decal, Warning Syms. CE Decal, Hp. Engine Decal, Hood RH/LH Decal, Wheel Steering Decal, 100 DBA Decal, Bat. Dan./Poi Decal, Rear Plate Decal, Fender Decal, Warning Eng. Syms Decal, Mower Cutfinger Symbol Decal, Brake/Clutch Symbol Lt Decal, Chassis Hot Muffler Decal, Saddle Brake Parking Decal, Bypass Fender CRD Decal, Hex Belt Sch. 92 CRD Decal, Lift Handle Pad Footrest RH Pad Footrest LH Manual Operator's (Euro) Manual Parts WHEELS & TIRES , 7 4,10 3, Cap Valve Tire Stem Valve Tire F Ts 15 x Service Tube Inner Front # Rim Asm. 6" Front White Service Fitting Grease Bearing Flange Rim Asm. " Rear White Service Tire R Ts 20 x 10- Service Tube Rear 9 5 x Service Cap Axle Blk x Sealant, Tire (10 oz. Tube) wheel_1 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 13

14 ENGINE OPTIONAL EQUIPMENT Spark Arrester engine-crd_bs_20 14

15 ENGINE Control Throt./Ck Screw Hex Thd. Cut. 1/4-20 x 1/ Engine B&S Model 31A B Muffler Gasket Muffler Shield Brn./Dbr. Guard Control Choke Kit Spark Arrester (Flat Scrn.) Tank Fuel Cap Asm. Fuel Top Clamp Hose Blk Line Fuel Screw Hex Wsh. Thdrol. 1/4-20 x 3/ Screw Hex Wsh. Thdrol. 3/- x 3/ Washer 9/32 x 7/ x Ga Screw Socket Head 5/-1 x Screw 3/- x 1/ Nut Keps Hex 1/4-20 unc Extension Drain Oil NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision ). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual on-site or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 15

16 MOWER _clutch_mod_ Deck-CRD_97cm_Elect_7

17 MOWER Housing Asm. Mower Bracket Asm. S-Bar Chass Retainer Spring Bar Sway Bolt 3/-24 x 1.25 Gr. Patched Washer Lock Hvy 3/ Unplated Washer Hard Blade Mower Vented Blade 3-1 LH Shaft Asm. w/lower Bearing Housing Mandrel Vented (Machd) Bearing Ball Mandrel Blade 3-1 RH Bolt Carriage 3/- x 1-1/ Bolt Shoulder 5/-1 Thd Form Bolt 3/-24 x 1.25 Gr. Ptch Lhthd Bracket Idler Sprt Bracket Asm. Susp. Rear RH Screw Thd Rolling Washer Spacer Mower Vented Mandrel Pulleys Nut Flg Top Lock Pulley Idler V-Groove Dim Nut Crownlock 3/- unc Nut Lock Flg. 3/- unc Cover Mandrel LH Cover Mandrel RH Arm Idler Spacer Retainer Mower Spring Tension Belt Knob Belt, Drive Shaft Asm w/lwr Brg RH Thd Keeper Belt Idler Bolt Shoulder Wheel Gauge Washer 13/32 x 1-1/4 x 12 Ga Bolt Carr Sh 3/- x 1-1/2 Gr Chute Bagger Cable Clutch CRD Screw Thd. Cut 1/4-20 x 1/ Head Asm. Cable Clutch Screw Thdrol 3/- x 1/ Screw 3/- x 1-3/ Mandrel Assembly (Includes housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) Mandrel Asm CRD LH Threads SVC Replacement Mower, Complete (Std. Deck - Order separately gauge wheel components key nos ) NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 17

18 36_mulch plug (CRD) REPAIR PARTS BAGGER Tube Handle Bagger CRD Nut Lock 1/4 Lge. Flg. Gr. 5 Zinc Handle Bagger w/lvrs. Blk. CRD Screw Pan Head #10-24 x 1.50 Blk Screw Pan Hd Nut Wiz Lock Hex Serr./Hd Cover Bagger Bolt Carriage 1/4-20 x 2.25d x Gr Tube Support Bagger CRD Bracket Support Upper Bag CRD Bracket Pivot LH Bolt 3/- unc x 3/ Bolt Fin. Hex 3/- x 2-1/4 Gr Retainer Spring Nut Lock Flg. 3/- unc Bolt Rdhd. Sht. Sqnk. 5/ -1 unc x 3/ Nut Lock Hex Flange 5/ Bracket Pivot RH Bag Asm. CRD Bracket Side Bagger CRD Tube Pivot Bagger CRD Tube Front Bagger Grip Handle Retainer Clip Rivet Rd. Hd. Drilled 3/ Dia Plug Mulch Handle Mulcher Pin Mulcher Washer 13/32 x 1-1/4 x 12 Ga Plug Support Bagger CRD Bolt 5/-1 x 2-1/ Seal Bracket Bagger SD Electric CRD Plug Tubing End Bolt Carr. 5/-1 x 1-1/4 Gr Tube Upper Bagger Bar Spreader Bagger Nut Lock Hex w/ins. 5/-1 unc Latch Spring Bagger Nut Keps Hex 1/4-20 unc Bolt Rdhd. Sqnk. 1/4-20 x 3/4 Gr. 5 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 35

19 MOWER LIFT lift-rh.1piece_ Plunger Asm. Lift Lever Shaft Asm. Lift Pin Groove E Ring # Washer 21/32 x 1 x 21 Ga Bearing Nylon Grip Handle Bicycle Button Plunger Link Asm. Lift LH Link Asm. Lift RH Retainer Spring NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm Link Front Nut Jam Hex 1/2-13 unc Trunnion Blk. Zinc Nut Lock w/wsh. 1/2-13 unc Arm Suspension Mower Retainer Spring Bearing, Pvt. Lift Nut Crownlock 3/-24

20 GARANTIE LIMITÉE Le Fabricant garantit son produit à l acheteur initial comme exempt de tout défaut de matière et de fabrication. Pendant un (1) an, à compter de la date d achat de la part de l acheteur initial, nous réparerons où remplacerons à notre choix, gratuitement, toute pièce, sur laquelle nous estimerons qu il existe un défaut de matière ou de fabrication. Cette garantie est soumise aux limitations suivants et exceptions: 1. Cette garantie ne couvre pas le moteur, la transmission/composants de transmission, la batterie (sauf comme mentionnée ci-dessous) ou les pièces detachées. Veuillez-vous consulter la garantie applicable du fabricant des articles. 2. L'acheteur est responsable de coût du transport de tous les équipements actionnés par moteur ou les accessoires. L'acheteur est responsable de coût aussi du transport de toutes les pièces (couvertes par cette garantie) soumies pour remplacement à moins que Electrolux Home Products demande à l'acheteur de renvoyer les pièces. 3. Garantie de la batterie: Pour les produits équipés d une batterie, nous remplacerons, gratuitement, toute batterie estimée défectueuse pendant les quatre-vingt-dix (90) jours initiaux suivant l achat. Après quatre-vingt-dix (90) jours, nous échangerons la batterie, le coût pour vous être 1/12 du prix d'une nouvelle batterie pour chaque mois complet à compter de la date d'achat initial. La batterie doit être entretenue selon les directives données dans la docu men ta tion appropriée. 4. La période de garantie applicable aux produits proposés en location ou à des fins commerciales est limitée à quarante-cinq (90) jours à compter de la date d achat initial. 5. Cette garantie ne s applique qu aux produits correctement assemblés, règlés, utilisés et entretenus con formément aux instructions données dans la documentation appropriée. Cette garantie ne s applique pas aux produits qui ont été modifié, utilisés incorrectement, abusés, mal assemblés, mal installés ou endommagés lors de la livraison ou usage normal. 6. Exclusions: Les courroies, lames, moyeux de lames, usage normal, réglages normaux, quincaillerie ordinaire, et entretien normal sont exclus de cette garantie. 7. En cas de problème entrant dans le cadre de cette garantie, veuillez contacter votre point de vente, en indiquant le numéro du modèle, le numéro de série, la date d'achat de votre machine. Cette garante ne s'applique pas aux dommages accidentels. Toutes garanties implicites sont limitées aux mémes périodes de temps. Ou contacte: E.M. Services 54 Rue Lambrechts Courbevoie - France Telephone: (1) Fax: (1) CETTE GARANTIE NE S'APPLIQUE PAS AUX DOMMAGES ACCIDENTELS. TOUTES GARANTIES IMPLICITES SONT LI- MITÉES AUX MEMES PERIODES DE TEMPS BAD Printed in the U.S.A.

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION

KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 874 78 04-10 Bolt, Fin Hex 1/4-20 x 5/8 12 532 13 09-86 Lens, LH 3 532 12 84-45 Bracket, Pivot Hood LH 13 532 13 09-84 Grille 4 819 09 10-16 Washer, Flat 1/4 21 532 12 69-38 Bumper, Hood 5 817 49 05-12