These days, I am more involving WAN Ethernet service product which is a bit complicated to

Transcription

1 These days, I am more involving WAN Ethernet service product which is a bit complicated to troubleshoot. Simply, tons of vendors and gears in the market. If you are not dealing with those devices all the time, you would spend time to play with some commands until you get output what you want. WAN Ethernet service is very popular in data communication market in compatible price. By comparing to traditional circuit, it is a lot cheaper. Also, H/W cost is cheaper. It dramatically drops your maintenance cost. For those reasons, WAN Ethernet service will get more sunshine in the market. By the way, there are many vendors out there. Seems like major players are Tellabs, Fujitsu, Cisco, Nortel, Ciena Corporation, Overture networks, Anda networks and etc. Here is the basic commands for overture ISG5100 Ethernet Switch for carriers. - To see uptime Overture_ISG5100# uptime 10:40pm up 42 days, 3:03, load average: 0.00, 0.00, / 9

2 - To see all VLAN Overture_ISG5100# port show all vlan Amt Port Type Pvid Pri Only IngF Vlan/Label Cir Burst Flow Pause 2.1 Enet 0 1 off off none N/A N/A N/A N/A 2.2 Enet 0 1 off off none N/A N/A N/A N/A 2.3 Enet 0 1 off off none N/A N/A N/A N/A 2.4 Enet 0 1 off off none N/A N/A N/A N/A 2.5 Enet 0 1 off off none N/A N/A N/A N/A 2.6 Enet 0 1 off off none N/A N/A N/A N/A 2.7 Enet 0 1 off off none N/A N/A N/A N/A 2.8 Enet 0 1 off off none N/A N/A N/A N/A 3.1 OC3 0 1 off off mgmt 1 2 N/A N/A - To show L2 class interface Overture_ISG5100# l2classify show Egress Rate Limt RuleName Pri Port VLAN DSCP Pbit Port Q Action Cir/Burst PBit DSCP OVR any any any PU/ / 100 no no OVR any any PO/ n/a no/ 0 no no - To check a status of port Overture_ISG5100# port show 1.1 status 2 / 9

3 Showing Port status Port Type Admin Oper Duplex Speed AutoNeg Lpbk RxErrTotal 1.1 Enet up up Full 100M n/a disab To see port configuration Overture_ISG5100# port show 1.1 config Admt Dot InFwd Spd Full Auto Port Type Admin Learn Polc Jmbo Only 1p Mode 100M Dup Neg Xovr 1.1 Enet up off off on off off sw/br on on off mdi Overture_ISG5100# - To check VLAN setup Overture_ISG5100# port show 1.1 vlan Amt Port Type Pvid Pri Only IngF Vlan/Label Cir Burst Flow Pause 1.1 Enet 0 1 off off none N/A N/A N/A N/A - To check details of the port Overture_ISG5100# port show 1.1 detail 3 / 9

4 Showing port details Port Type Drops Rx Tx Q Disc Bundle 1.1 Enet N/A - To check detail counters Overture_ISG5100# port show 1.1 detail counters Showing port detailed counters -- Counters for TX_BYTES_GOOD RX_BYTES_GOOD TX_BYTES_TOTAL RX_BYTES_TOTAL TX_UNICAST_PKTS RX_SHORT_PKTS_GOOD TX_MULTICAST_PKTS RX_SHORT_PKTS_BAD TX_BROADCAST_PKTS RX_LONG_PKTS_GOOD TX_PAUSE_PKTS RX_LONG_PKTS_BAD TX_VLAN_PKTS RX_UNICAST_PKTS TX_CRC_ERRS RX_MULTICAST_PKTS TX_DEFERS RX_BROADCAST_PKTS TX_EXCESS_DEFERS RX_PAUSE_PKTS TX_SINGLE_COLS RX_VLAN_PKTS TX_MULTI_COLS RX_CRC_ERRS TX_EXCESS_COLS RX_ALIGN_ERRS TX_LATE_COLS RX_RUNTS TX_NORM_COLS RX_LENGTH_ERRS TX_FIFO_ERRS RX_FALSE_CRS TX_PKTS_ RX_PHY_ERRS TX_PKTS_ RX_FIFO_ERRS TX_PKTS_ RX_IGNORED TX_PKTS_ RX_OPCODE_BAD TX_PKTS_ RX_PKTS_ TX_PKTS_ RX_PKTS_ RX_PKTS_ RX_PKTS_ RX_PKTS_ RX_PKTS_ / 9

5 - To clear PM counters Overture_ISG5100# port clear 1.1 pm-counters - To see PM result, only apply serial link not Ethernet. Overture_ISG5100# port show 3.1 pm Showing PM Counters Port Type Section ES SES SEFS CV Port Type Line ES SES CV UAS Port Type FarendLine FEES FESES FESCV FEUAS Port Type Path ES SES CV UAS Port Type FarendPath FEES FESES FECV FEUAS Overture_ISG5100# - To see queues Overture_ISG5100# port show all detail queues 5 / 9

6 Port Type Cntr Queue0 Queue1 Queue2 Queue3 Queue4 Queue5 Queue6 1.1 GigSFP Bytes Pkts OC3 Bytes Pkts To see errors on the interface Overture_ISG5100# port show 1.1 errors Showing Port Errors Port Type RxCrc RxAlign RxRunt RxLength RxCrs RxPhy RxFifo 1.1 Enet To see live traffic on the link, default interval is 5 sec Overture_ISG5100# port show 1.1 util Per Second Utilization for Port(s) 1.1 Count=0 DisplayTime=5 Secs Port Type TxPkts RxPkts TxBits RxBits Tx % Rx % 1.1 Enet Kbps Mbps Port Type TxPkts RxPkts TxBits RxBits Tx % Rx % 1.1 Enet Kbps Mbps To see log for alrams 6 / 9

7 Overture_ISG5100# log show alarm Aug 13 19:31:53 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:31: " SEVERITY="Major" SLOT="Slot 3" DEVICE="port 1" ID="Section Loss of Frame (LOF)" SEQUENCE NUMBER="1" Aug 13 19:31:54 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:31: " SEVERITY="Cleared" SLOT="Slot 3" DEVICE="port 1" ID="Section Loss of Frame (LOF)" SEQUENCE NUMBER="2" Aug 13 19:33:12 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:33: " SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1" ID="Link failure" SEQUENCE NUMBER="3" Aug 13 19:34:36 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:34: " SEVERITY="Cleared" SLOT="Slot 1" DEVICE="port 1" ID="Link failure" SEQUENCE NUMBER="4" Aug 13 19:34:49 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:34: " SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1" ID="Link failure" SEQUENCE NUMBER="5" Aug 13 19:45:37 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:45: " SEVERITY="Cleared" SLOT="Slot 1" DEVICE="port 1" ID="Link failure" SEQUENCE NUMBER="6" Aug 13 19:46:37 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:46: " SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1" ID="Link failure" SEQUENCE NUMBER="7" - To see log for command history Overture_ISG5100# log show command Sep 1 12:48:10 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show all vlan" Sep 1 12:52:40 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 status" Sep 1 12:52:56 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 detail" Sep 1 12:52:58 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 detail" Sep 1 12:53:16 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 detail counters" Sep 1 12:54:12 isg5000 cli_sh: CLI USER="AshburnCMC" 7 / 9

8 IP_ADDR=" " CMD="port show 1.1 detail counters" Sep 1 12:54:13 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 status" Sep 1 12:54:18 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 status" Sep 1 12:54:40 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 counters " Sep 1 12:54:52 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 detail" Sep 1 12:54:57 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 detail counters" Sep 1 12:55:09 isg5000 cli_sh: CLI USER="AshburnCMC" IP_ADDR=" " CMD="port show 1.1 status" : : - To see all config Overture_ISG5100# show status - To see start configuration Overture_ISG5100# config show 8 / 9

9 9 / 9