Quickstart Installation Checklist (Please refer to operation manual for complete installation instructions)

Transcription

1 Quickstart Installation Checklist (Please refer to operation manual for complete installation instructions) 1. Uncrate blender from packaging. 2. Lift the blender and position over machine throat or floor stand; set in position and secure by tightening bolts. 3. Mount the material conveying system receivers on top of the blender supply hoppers. 4. Align the weigh hopper on the load cell brackets. 5. Check the slide gate metering assemblies to ensure they freely slide back and forth. 6. Provide a correctly sized and protected power supply to the unit. The standard Slide Gate/Auger blending system is designed to operate on /1/60 or /1/50 supply voltage. A single 15A service is sufficient for most blenders (verify this with the blender s name plate information. If local electrical codes require fusing or disconnects, these items must be supplied, wired, and mounted by the customer. Each blending system MUST be connected to a separate source of power. 7. Attach the operator touch screen to the MAIN DISPLAY port on the blender. Always disconnect the power supply before servicing the unit. 8. The Slide Gate/Auger blending system requires approximately 1 CFM (1.7 m³/hr) at 60 PSI (4.14 bar) maximum air pressure to operate properly. (See figure below). The air supply should be filtered through a 5 micron air filter with a water separator. 9. The blender should use a dedicated line to ensure proper air supply. To prevent damage to the equipment, do not exceed 60 PSI (4.14 bar) air pressure. Always disconnect the air supply when conducting any kind of maintenance. Unit Operation (Please refer to operation manual for complete instructions.) 1. Check to make sure all ingredient supply hoppers to be used are filled with material. 2. Turn ON the blender using the ON/OFF selector switch on the control panel. 3. Wait for Main Recipe Screen to appear on the touch screen; it may take up to one minute. (See figure below). 4. Enter the recipe using the operator touch screen. Press Accept New Recipe when finished. 5. Press the Push to Start or Stop the Blender to begin the blending process.

2 Main Recipe Screen Display Recipe Entry Mode New Recipe Input Actual Weight Indicator for Timed Batch Mixer Status Start/Stop Blender Immediately Stop Blender Accept New Recipe Target Weight Go To Recipe Book Feeder Type Indicator Go To Inventory Screen Quick Controller Setup (Change controller to EZ mode for injection or PERCENTAGE mode for extrusion.) 1. From the Recipe Page, touch the ACS icon, enter 5413, and press the key. 2. Press Recipe Format. Toggle through the EZ, Percentage, or Parts modes (see figure below). 3. Press the Done key two times until you return to the Recipe Page. 4. Enter your new recipe as described above, if necessary. Touch Here to Change

3 Checking the Calibration (Please refer to operation manual for complete calibration instructions.) NOTE: It is not necessary to calibrate the weight scale on a brand new blender; although, it is recommended that the calibration be checked periodically to ensure that the reported inventory totals are accurate. A bad calibration is worse than no calibration in most cases. 1. From the Recipe Page, touch the AEC icon and enter 5413 ; then press the key. 2. Touch Calibration and then Direct Scale Readout. (See figure below.) 3. Remove the weigh hopper if possible to do without tools (Don t do this for OA blenders). 4. Locate the weight display for each load cell,or one load cell for OA blender with an HC style mixer. Record values. 5. Add the calibration weight to each load cell mounting bracket and record the value displayed in weight, as in step Subtract the values recorded in steps 4 and 5. This is the measured weight. If the measured weight is within lbs. of the weight stamped on the calibration weight, then it is within specification. If not, then follow the steps below to calibrate the blender. 7. Store the calibration weights in a safe location DO NOT DISCARD! Direct Scale Readout Display Current Loadcell Weight Current Loadcell Weight Calibrating if necessary 1. From the Recipe Page, touch the AEC icon and enter 5413, then press the key. 2. Touch Calibration and then Scale Calibration (see figure below). 3. Follow the onscreen instructions to complete the calibration. 4. The blender will evaluate the calibration and indicate if it is properly calibrated. 5. Press the Done key three times, and you will return to the main menu. Calibration Menu Screen Enter in the Calibration Weight Current Loadcell Bits Follow Instructions Press here to perform the calibration Go Back to the Calibration Directory

4 Menu Structure for Allen-Bradley Control System Recipe Page Start Change Recipe Values by touching the number you wish to change Touch Accept New Recipe button after you ve made the desired changes Touch Undo button to cancel a recipe change before accepting it Start or stop the blender by touching the Push to Start or Stop button Access Recipe Book Page Access Clean Out Page Access Inventory Page Access Setup Page Recipe Book Page Save the running recipe to the book. Delete a stored recipe Load a stored recipe Erase all stored recipes Modify the product ID for a stored recipe Return to the Recipe Page Clean Out Page Empty the blender hoppers Manually operate mixer, weigh hopper dump gate,, and slide gate below mixer View/test all inputs/outputs on the blender Return to Recipe Page Inventory Page View/print accumulated inventories View batch time View maximum capacity View average process rate Return to Recipe Page Setup Page Touch the AEC icon and enter in user password Recipe Format Percentage, Parts, or EZ mode Metering order Batch size Inventory shutdown Batch ready mode Auto start mode Weigh every batch options Change recipe without stopping Report Setup Blender number Auto print option Auto clear option Auto interval option Auto start time Calibration Scale Calibration Direct Scale Readout Feeder Calibration Mixer & Dump Setup Mixing time Remix time Dump time Dump delay Dump cycles Mixer dump time Time/continuous mixing option Panel View Config View software version Access Panel View Config setup to modify printer/time settings and to load new software User Password Change default user password Units Blender data units (lbs/kg) Target v. actual data units (lbs/kg) Alarm Log View, print, or clear alarm log Alarm Setup Stop/Continue when out of material Alarm/No Alarm when out of material Alarm Silence delay Accept recipe alarm enable/disable Network Setup IP Address Subnet Mask Send Config to ENI Module Enable Ethernet Configurator Modbus Plus Disabled Recommended Spare Parts (Please refer to operation manual for complete list) User Interface Lock Lock the user interface to prevent others from making changes or viewing the blender Part Description 150 Model 500 Model 900 Model 2500 Model 4000 Model 6000 Model Mixer gear motor # Mixer agitator # Mixer coupling N/A Weigh hopper asbly. # A A A A A Valve stock asbly. N/A A (4-component) or A (6-component) A/B Panel View operator touch screen (no enclosure) A/B PLC MicroLogix CPU A/B PLC Base A

5

6

7

8