Title: Fall Protection

Transcription

1 1. Purpose The purpose of this procedure is to provide guidance to employees that are working at heights at or above 4 feet. This procedure establishes the minimum acceptable elements of a Fall Protection policy. Regulatory Note. The Occupational Safety and Health Administration (OSHA) standard is Duty to have fall protection and falling object protection and applies to this work instruction. 2. Forms HSF Roof Access Permit Permit provides a review of potential roof entry hazards, and means to minimize or eliminate the hazard prior to working on the roof. 3. Definitions 3.1. Authorized person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard Competent person: means a person who is capable of identifying hazardous or dangerous conditions in the personal fall arrest system or any component there of, as well as in their application and use of related equipment. A competent person is not a qualified person (Defined 3.3) Qualified person: A person with a recognized degree or professional certificate and with extensive knowledge, training, and experience in the fall protection and rescue field who is capable of designing, analyzing, evaluating, and specifying fall protection and rescue systems to the extent required by this standard Designated Area: Designated area means a distinct portion of a walking-working surface delineated by a warning line, signage, painted etc. in which employees may perform work without additional fall protection Dockboard: means a portable or fixed device that spans a gap or compensates for a difference in elevation between a loading platform and a transport vehicle. Dockboards include, but are not limited to, bridge plates, dock plates, and dock levelers. 4. Fall Hazards Specific to Waupaca Foundry, Inc Working on top of machinery and equipment such as Vertical Molding Machines (VMM), Core machines, casting coolers, conveyors, or overhead cranes Working on overhead plant facilities equipment such as heaters, blowers, exhaust equipment, air conditioners, and piping systems Working on building roofs including hazards from roof openings, unsupported surfaces, or working near the roof edge Working at heights on conduit, wiring, cable trays, ductwork, piping, lighting fixtures Walking or working on overhead I-Beams or H-Beams Exposure to falls into or onto tanks, scrap pits/containers, moving conveyors or compactors Working in High Reach equipment (Raymond lift), or on Aerial work platforms Employees working on aerial lift platforms shall maintain a firm footing on the platform. The use of ladders, planks or other devices within the lift to achieve additional height is prohibited Extending and articulating boom platform lifts require personal fall protection equipment to be worn and anchored inside of the lift Vertical lift equipment provide adequate fall protection as long as the guardrails are in place on all sides of the lift and the occupant stands firmly on the floor of the lift platform, and do not - 1 -

2 climb on or lean over guardrails or handrails. If employees cannot remain on the platform, and must climb or lean on the guardrails, personal fall protection must be used. 5. Means of Fall Prevention and Hazard Control: Fall Prevention includes any means used to reasonably prevent exposure to a fall hazard. All company employees involved in work activity that exposes them to a fall hazard of 4 feet or greater shall minimize the exposure by using one or more of the following: 5.1. Elimination of the hazard. Procedural changes may be made to eliminate hazards that consider another method for completing the work such as the use of aerial lift equipment or high reach tools such as long handled disconnects rods or bulb extractors Guarding against the hazard. Engineering controls may guard against the hazard. Such controls are physical changes or additions to the work area. Examples may include a standard guardrail and toe board, properly designed catwalks and access platforms, gates, floor and wall opening covers Standard guardrails are to be used for open-sided floors, platforms and runways four feet or more above the adjacent floor or ground level on all open sides, except where there is an entrance to a ramp, stairway, or fixed ladder A standard guardrail consists of a top rail and posts with a vertical height of 42 from the upper surface of the top rail to the floor or platform. The intermediate rail shall be approximately halfway between the top rail and the floor Posts and framing shall be constructed to withstand a load force of 200 pounds applied in any direction at any point of the top rail Toe boards are 4 inches in vertical height and should be included whenever persons can pass beneath the open sides, or when there is moving machinery, or equipment from which falling materials could create an additional hazard Use of personal fall arrest systems designed to protect an employee during a fall. Included in this system are a body harness, lanyard, and anchorage which are tested devices that function together to stop a freefall and minimize the potential for injury. A fall arrest system shall only be used after other solutions have been exhausted Consideration should be give to other contributing factors when choosing appropriate fall protection. For example the number of employees in the area, the amount of time to be spent in the area, the frequency of entry into the area and weather conditions such as wind, rain or snow and ice that may create additional hazards in combination with a fall. 6. Roof Work 6.1. Work that is performed less than 6 feet from the roof edge, requires that each employee is protected from falling by a guardrail system, safety net system, travel restraint system, or personal fall arrest system. A roof entry permit must be completed unless permanent fall protection is in place When work is performed at least 6 feet but less than 15 feet from the roof edge, the employee will be protected from falling by using a guardrail system, safety net system, travel restraint system, or personal fall arrest system or a designated area may be used IF: The work is Infrequent and temporary: Considered to be less than 2 hours time, and work that is planned and/or part of a preventative maintenance program example: changing filters, belts etc. on HVAC equipment Employees are prohibited from going within 6 feet of the roof edge without having the protection of additional fall protection as outlined in Designated area means a distinct portion of a walking-working surface delineated by a warning line, signage, painted etc. in which employees may perform work without additional fall protection

3 During the interim of time (2018) where guardrails and designated areas are being determined and marked accordingly ; a roof permit may be used in lieu of these requirements (Section only) When work is performed 15 feet or more from the roof edge, the employee will be protected from falling by a guardrail system, safety net, travel restraint, or designated area No fall protection/no Permit is required for work that is infrequent and temporary 15 feet or more from the roof edge. Considered to be less than 2 hours time, and work that is planned and/or part of a PM program. Employees that are working 15 feet of more from the roof edge, are not allowed to go within 15 feet of the roof edge During the interim of time (2018), if work is not infrequent and temporary, a Roof Entry Permit is required, and employees are prohibited from going within 6 feet of the roof edge without using fall protection Contractors involved in Roof Access/Work: Must complete pre job meeting/planning with WF job site supervisor and/or Plant Safety Must complete Roof Work permit for all roof access Must be accompanied by a trained/authorized WF employee at all times. *Unless the roof that will be accessed is completely guarded Must wear a Hi-Viz yellow shirt, jacket or vest while on the roof Communication Signage must be affixed to all doors leading to Roofs that state: Roof Access, Authorized Personnel Only, Fall Hazard Authorized personnel accessing the roof must wear a Hi-Viz yellow shirt, jacket or vest while on the roof Authorized WF personnel may access the roof either with a co-worker who will check the welfare of each other, or via radio/phone contact with someone on the ground at intervals no less than 15 minutes. 7. Designated areas. When the employer uses a designated area, the employer must ensure: 7.1. Employees remain within the designated area while work operations are underway; and 7.2. The perimeter of the designated area is delineated with a warning line consisting of a rope, wire, tape, or chain that meets the requirements below: 7.3. The employer must ensure each warning line: Has a minimum breaking strength of 200 pounds (0.89 kn); Is installed so its lowest point, including sag, is not less than 34 inches (86 cm) and not more than 39 inches (99 cm) above the walking-working surface; Is supported in such a manner that pulling on one section of the line will not result in slack being taken up in adjacent sections causing the line to fall below the limits Is clearly visible from a distance of 25 feet (7.6 m) away, and anywhere within the designated area; Is erected as close to the work area as the task permits; and Is erected not less than 6 feet (1.8 m) from the roof edge for work that is both temporary and infrequent, or not less than 15 feet (4.6 m) for other work When mobile mechanical equipment is used to perform work that is both temporary and infrequent in a designated area, the employer must ensure the warning line is erected not less than 6 feet (1.8 m) from the unprotected side or edge that is parallel to the direction in which the - 3 -

4 mechanical equipment is operated, and not less than 10 feet (3 m) from the unprotected side or edge that is perpendicular to the direction in which the mechanical equipment is operated. 8. Equipment and/or Material Hoist areas 8.1. Each employee in a hoist area is protected from falling 4 feet (1.2 m) or more to a lower level by a guardrail system; a personal fall arrest system; or a travel restraint system When any portion of a guardrail system, gate, or chains are removed, and an employee must lean through or over the edge of the access opening to facilitate hoisting, the employee is protected from falling by a personal fall arrest system If grab handles are installed at hoist areas, they must meet the requirements of (l). 9. Holes Each employee must be protected from falling through any hole (including skylights) that is 4 feet (1.2 m) or more above a lower level by one or more of the following: Covers; Guardrail systems; Travel restraint systems; or Personal fall arrest systems Each employee must be protected from tripping into or stepping into or through any hole that is less than 4 feet (1.2 m) above a lower level by covers or guardrail systems Each employee must be protected from falling into a stairway floor hole by a fixed guardrail system on all exposed sides, except at the stairway entrance. However, for any stairway used less than once per day where traffic across the stairway floor hole prevents the use of a fixed guardrail system (e.g., holes located in aisle spaces), the employer may protect employees from falling into the hole by using a hinged floor hole cover that meets the criteria in and a removable guardrail system on all exposed sides, except at the entrance to the stairway Each employee must be protected from falling into a ladderway floor hole or ladderway platform hole by a guardrail system and toeboards erected on all exposed sides, except at the entrance to the hole, where a self-closing gate or an offset must be used Each employee must be protected from falling through a hatchway and chute floor hole by: A hinged floor-hole cover that meets the criteria in and a fixed guardrail system that leaves only one exposed side. When the hole is not in use, the employer must ensure the cover is closed or a removable guardrail system is provided on the exposed sides; A removable guardrail system and toeboards on not more than two sides of the hole and a fixed guardrail system on all other exposed sides. The employer must ensure the removable guardrail system is kept in place when the hole is not in use; or A guardrail system or a travel restraint system when a work operation necessitates passing material through a hatchway or chute floor hole. 10. Dockboards (Definition 3.5) The employer must ensure that each employee on a dockboard is protected from falling 4 feet (1.2 m) or more to a lower level by a guardrail system or handrails A guardrail system or handrails are not required when: Dockboards are being used solely for materials-handling operations using motorized equipment; Employees engaged in these operations are not exposed to fall hazards greater than 10 feet (3 m); and Those employees have been trained in accordance with Runways and similar walkways, ie: catwalks. The employer must ensure each employee on a runway or similar walkway is protected from falling 4 feet (1.2 m) or more to a lower level by a guardrail system

5 11.1. When the employer can demonstrate that it is not feasible to have guardrails on both sides of a runway used exclusively for a special purpose, the employer may omit the guardrail on one side of the runway, provided the employer ensures: The runway is at least 18 inches (46 cm) wide; and Each employee is provided with and uses a personal fall arrest system or travel restraint system. 12. Dangerous equipment. The employer must ensure each employee less than 4 feet (1.2 m) above dangerous equipment is protected from falling into or onto the dangerous equipment by a guardrail system or a travel restraint system, unless the equipment is covered or guarded to eliminate the hazard Each employee 4 feet (1.2 m) or more above dangerous equipment must be protected from falling by: Guardrail systems; Safety net systems; Travel restraint systems; or Personal fall arrest systems. 13. Openings. The employer must ensure that each employee on a walking-working surface near an opening, including one with a chute attached, where the inside bottom edge of the opening is less than 39 inches (99 cm) above that walking-working surface and the outside bottom edge of the opening is 4 feet (1.2 m) or more above a lower level is protected from falling by the use of: Guardrail systems; Safety net systems; Travel restraint systems; or, Personal fall arrest systems. 14. Repair pits, service pits, and assembly pits less than 10 feet in depth. The use of a fall protection system is not required for a repair pit, service pit, or assembly pit that is less than 10 feet (3 m) deep, provided the employer: Limits access within 6 feet (1.8 m) of the edge of the pit to authorized employees trained in accordance with ; Applies floor markings at least 6 feet (1.8 m) from the edge of the pit in colors that contrast with the surrounding area; or places a warning line at least 6 feet (1.8 m) from the edge of the pit as well as stanchions that are capable of resisting, without tipping over, a force of at least 16 pounds (71 N) applied horizontally against the stanchion at a height of 30 inches (76 cm); or places a combination of floor markings and warning lines at least 6 feet (1.8 m) from the edge of the pit. When two or more pits in a common area are not more than 15 feet (4.5m) apart, the employer may comply by placing contrasting floor markings at least 6 feet (1.8 m) from the pit edge around the entire area of the pits; and Posts readily visible caution signs that meet the requirements of and state "Caution- Open Pit." 15. Fixed ladders (that extend more than 24 feet (7.3 m) above a lower level). For fixed ladders that extend more than 24 feet (7.3 m) above a lower level, the employer must ensure: Existing fixed ladders. Each fixed ladder installed before November 19, 2018 is equipped with a personal fall arrest system, ladder safety system, cage, or well; New fixed ladders. Each fixed ladder installed on and after November 19, 2018, is equipped with a personal fall arrest system or a ladder safety system; Replacement. When a fixed ladder, cage, or well, or any portion of a section thereof, is replaced, a personal fall arrest system or ladder safety system is installed in at least that section of the fixed ladder, cage, or well where the replacement is located; and Final deadline. On and after November 18, 2036, all fixed ladders are equipped with a personal fall arrest system or a ladder safety system When a one-section fixed ladder is equipped with a personal fall protection or a ladder safety system or a fixed ladder is equipped with a personal fall arrest or ladder safety system on more than one section, the employer must ensure: - 5 -

6 The personal fall arrest system or ladder safety system provides protection throughout the entire vertical distance of the ladder, including all ladder sections; and The ladder has rest platforms provided at maximum intervals of 150 feet (45.7 m) The employer must ensure ladder sections having a cage or well are offset from adjacent sections; and have landing platforms provided at maximum intervals of 50 feet (15.2 m) The employer may use a cage or well in combination with a personal fall arrest system or ladder safety system provided the cage or well does not interfere with the operation of the system. 16. Stairways. The employer must ensure each employee exposed to an unprotected side or edge of a stairway landing that is 4 feet (1.2 m) or more above a lower level is protected by a guardrail or stair rail system; Each flight of stairs having at least 3 treads and at least 4 risers is equipped with stair rail systems and handrails Each ship stairs and alternating tread type stairs is equipped with handrails on both sides. 17. Scaffolds and rope descent systems. The employer must ensure each employee on a scaffold is protected from falling in accordance 29 CFR part 1926, subpart L; and each employee using a rope descent system 4 feet (1.2 m) or more above a lower level is protected from falling by a personal fall arrest system. 18. Protection from falling objects Install toe boards along the edge of the overhead walking/working surface Require that toe boards: Are a minimum of nominal height of 3 1/2 inches in height Are capable of withstanding at least 50 pounds of force applied in any downward or outward direction That there is no more than ¼ inch clearance between the toe board and the walking/working surface Install paneling or screening from the top of the toe board to the top rail or mid rail when tools, equipment, or materials are piled higher than the top of the toe board When an employee is exposed to falling objects, the employer must ensure that each employee wears head protection that meets the requirements of 29 CRF In addition, the employer must protect employees from falling objects by implementing one or more of the following: Erecting toeboards, screens, or guardrail systems to prevent objects from falling to a lower level; Erecting canopy structures and keeping potential falling objects far enough from an edge, hole, or opening to prevent them from falling to a lower level; or Barricading the area into which objects could fall, prohibiting employees from entering the barricaded area, and keeping objects far enough from an edge or opening to prevent them from falling to a lower level. 19. Personal Fall Protection Equipment Selection and Care All fall protection equipment shall be approved by the Safety Department prior to purchase All components of the fall arrest system shall be compatible and interchangeable. Components of a fall arrest system shall not be used beyond the manufacturer s recommended date of expiration. As a general rule this is 5 years of use Only employees who have been trained and authorized (definition: 3.1) in hazard recognition and selection of proper fall protection shall be allowed to use personal fall arrest systems Permanently installed fall protection systems shall be inspected on a regular basis as determined by the Safety Department but at a minimum on an annual basis

7 19.5. Annual inspections by trained and competent person(s) (definition 3.2) are completed on all personal fall protection equipment, and documentation maintained Personal Fall Protection Equipment Components All systems are made up of three components, the anchor point, the body harness, and the decelerating device or lanyard Anchor Point General Requirements: The anchor point is a secure point of attachment for lifelines, lanyards, or deceleration devices The anchor point is independent and does not support or suspend the employee The anchor point must be able to support the weight of at least 5000 pounds per each worker attached; The anchor point should be located at a height that reduces the freefall distance to 6 feet or less; The anchor point should be located so that if a freefall occurs an attached worker will not collide with any lower level hazard; Work shall be done directly under the anchor point to avoid a swing-fall injury; When selecting an anchorage point, consideration to the shock absorber elongation (3.5 feet) must be given Anchor point must allow for the snap hook keeper to close completely; If anchorage point is questionable, plant engineering personnel should be contacted for further evaluation Examples of ACCEPTABLE Anchor Points include: Guard post or guardrails that have been constructed with 6 inch or larger steel pipe or square tubing in sound condition; All building columns; Structural I-Beam; Roof support Trusses; Any manufacturer identified anchor point in personal lifts or fork truck platforms; Any designated tie off points that have been approved by plant engineering for this purpose Examples of Unapproved Anchor Points include: Guard post or guardrails that have NOT been constructed with 6 inch or larger steel pipe or square tubing in sound condition; Ladders; C- Clamps (unless approved Universal Beam clamp ); Electric conduit; Pipe runs, unless approved by engineering based on pipe diameter, length of support, etc.) Anchor Point Inspection Inspect prior to each use for mildew, rust, wear, cracks or fracture, damage, and other deterioration. Defective anchor points should not be used and should be removed from service. Anchor points that are part of the building structure and found to be damaged shall be reported to engineering and not used Any non-structure anchor point that sustains the impact of fall forces shall be removed from service and turned into the Safety Department. Structural anchor points that sustain fall forces shall be reported to the engineering department Body Harness General Requirements: The body harness effectively distributes the impact load forces over at least the thighs, pelvis, waist, chest and shoulders thereby minimizing the possibility of injury in the event of a fall. Body belts shall never be used for fall protection but for positioning only when used in conjunction with a personal fall protection system The D-ring located in the upper middle of the back on the full body harness shall be used for fall protection. All other rings shall be used for positioning or rescue The harness shall fit snugly, yet comfortably over normal work clothing Buckles and pull straps should close completely around the legs, chest and waist Excess strap material shall be tucked into the keepers provided on the harness

8 Select the proper size harness. If the fit is uncomfortable, too loose, or the wearer weighs in excess of 310 lbs, contact the safety department for a custom fit harness and lanyard. A custom harness may be built and purchased for employees weighing between 310 lbs and 400 lbs Do not attach any tools or other snap hooks to fall arrest webbing, positioning suspension or retrieval D-rings on the harness Employees shall not alter the harness by adding buckle holes and/or cutting straps Body Harness Inspection Before each use, carefully inspect the harness for signs of mildew, wear, damage and other deterioration. Defective body harnesses shall not be used and removed from service Visually inspect the harness by running the webbing over your fingers looking for loose threads, pulled rivets, burns, cuts, abrasions and evidence of chemical or physical deterioration. If there is a risk of being cut while inspecting, wear gloves Visual inspect to ensure buckles meet the keepers and eyelets are not oblong or stressed Inspect all hardware components for cracks, nicks, and defects as well as an out of shape appearance which may damage or saw cut the webbing during use A full body harness that sustains the full impact of fall forces shall be removed from service and turned into the safety department Body Harness Care Clean and maintain the full body harness in accordance with manufacturer s instructions Wash the nylon harness in warm water with mild soap and hang by back D-ring to allow to completely dry Avoid the use of harsh chemicals or cleaners to clean the harness When not in service, hang the body harness by the back D-ring to prevent damage to the webbing and threading of the harness Connecting Devices General Requirements: The Connecting Device or Lanyard is a flexible line of rope, wire rope or strap which is used to secure the full body harness to a deceleration device, lifeline or anchorage. The device may be a one-time use style of lanyard or fall limiter or one that can be repaired and placed back into service Use only lanyards that contain a locking snap hook The lanyard shall be attached to the anchor point in such a manner that the free fall distance is limited to 6 feet The shock absorber on the lanyard will allow the lanyard to elongate an additional 3.5 feet. The additional distance must be taken into account when selecting an anchor point The lanyard shall be connected to the anchor point in such a manner as to prevent striking a lower level in the event of a fall Do not tie the lanyard in knots to shorten its length. Obtain a shorter lanyard or select the proper fall limiter Do not attach lanyards together. Select a proper fall limiter if more length is needed Do not tie a lanyard back onto itself unless specifically designed to do so by the manufacturer While traveling, do not attach the unused locking keeper back onto the webbing of the body harness. Use the provided tie off on the harness or hand carry Lanyards shall be constructed of either nylon or wire rope Never disable a locking keeper or alter the locking device in any way Do not use a lanyard for rigging

9 Prevent the lanyard from coming into contact with sharp surfaces, high temperatures, welding splatter or electrical wiring Wear pads shall be used to protect the lanyard from sharp surfaces and high temperatures Ensure the snap hook is so positioned so that it is never load bearing Ensure the locking keeper on both ends of the lanyard fully engage and lock onto the full body harness and anchor point respectfully Connector Device Inspection Before each use, carefully inspect the connector device for mildew, wear, damage, and deterioration. Defective connecting devices shall not be used and shall be removed from service Visually inspect for loose threads, pulled rivets, burns, cuts, abrasions or evidence of chemical or physical deterioration. If there is a risk of being cut while inspecting, wear gloves Inspect fall limiters for proper engagement and release of the stop mechanism All snap hooks and carabineers shall be checked for sharp edges, defects and cracks that may damage or saw cut the webbing while in use Any connecting device that sustains the full impact of fall forces shall be removed from service and turned into the Safety Department. 20. GUARD RAIL SYSTEMS: Waupaca Foundry, Inc. will provide guardrail systems, when feasible, at all locations where a fall hazard of 4 feet or greater exists Where guardrail systems are impractical, an alternative form of fall protection as outlined elsewhere in this procedure must be provided Require that guardrail systems meet the following criteria: Top rails must be installed 42 inches above the walking/working surface and be capable of withstanding, without failure, a minimum force of 200 pounds in any outward or downward direction with no more than 3 inches of deflection Mid rails must be installed 21 inches above the walking/working surface and be capable of withstanding, without failure, a minimum force of 150 pounds in any outward or downward direction Posts must be spaced not more than 8 feet apart on centers There are no openings more than 19 inches wide in any guardrail system Do not use plastic or steel banding as top rail or Provide top rails and mid rails of at least one-quarter inch nominal thickness or diameter, and smoothly surfaced to prevent cuts and punctures Flag the top rail with high-visibility material when using wire rope for top rails Erect guardrails on all sides when using guardrail systems around holes When guardrails are used around holes that are used for access, such as ladder ways, provide a gate or offset the guardrail so that a person cannot walk directly into the hole When guardrails are used at hoisting areas, place a chain, gate, or removable guardrail section across the access point when hoisting operations are not taking place Provide guardrail systems at all locations above dangerous equipment, whether 4 feet or not Provide guardrails at all wall openings where the outside bottom edge of the opening is 4 feet or more above lower levels and the inside bottom edge of the wall opening is less than 39 inches above the walking/working surface

10 Erect guardrail systems on all unprotected sides or edges of ramps and runways when such systems are used. 21. Education and Training: It is the responsibility of the company to provide training to the employees in the areas of hazard recognition, fall prevention, fall hazards, and available fall protection systems This classroom training (or equivalent) shall occur at a minimum of every two years. In addition, fall protection awareness level training is provided every 2 years to all employees via the monthly safety talk The training shall include the following topics: When and where fall protection is required Requirements for the use of fall protection How to inspect fall protection equipment How to maintain and care for fall protection equipment Proper donning and doffing of fall protection equipment which includes full body harnesses, Lanyards, anchor points as well as weight limits of components How to identify proper anchor points What to do in the event the employee sustains fall forces What to do with fall protection equipment that has sustained full fall forces 22. Responsibility Company Responsibility: Provide equipment appropriate for the fall hazard(s) Provide competent training to employees addressing the prevention and protection systems available for use and the hazards involved Retraining will be provide if changes in the workplace render previous training obsolete, if there are changes in the equipment used, or if the employees do not understand, or demonstrate understanding and the ability to use appropriate fall protection Ensure adequate supervision of employees involved in areas involved in the fall protection program Assist in preplanning for specific job tasks as requested, provide additional information, equipment and training as needed or requested Project Manager, Supervisor, and Foreman: Evaluate each work during preplanning for a job/work area for fall hazards, and select the most appropriate fall protection in order to eliminate the hazard. This selection may include elimination of the fall hazard, permanent guarding of the area, or temporary fall protection such as personal fall protection equipment The manager is required to evaluate all work areas with a fall hazard of 4 feet or more prior to the work starting. A decision shall then be made regarding the fall protection that will be used. The primary responsibility is taking the time to evaluate the work If an employee sustained a fall could the following questions be answered? Why wasn t a guardrail in place? Why wasn t an aerial lift used? Why wasn t the person tied off properly? Did you ask for assistance from your supervisor or the safety dept? Supervision of personnel involved in work with a fall hazard of 4 feet or more. Ensure proper use and understanding of the equipment in use. This supervision includes the use of discipline for employees that do not follow the policy, neglect to use the fall protection, or use it inappropriately

11 Supervision shall identify and communicate means to contact the Emergency Response Team to respond to a fall incident / suspension trauma Complete and Authorize Roof Access Permits as needed Employees: It is the responsibility of the employee to use the most appropriate fall protection when at a height at or above 4 feet The employee shall be familiar with the fall protection equipment and use it appropriately Prior to use, the employee shall inspect the components of the fall protection equipment, and damaged equipment, or equipment that has sustained a fall shall be removed from service Employees shall understand the means to contact the Emergency Response Team to respond to a fall incident / suspension trauma