2017 PRODUCT CATALOG. Nelson Wire Rope Corporation 3051 Penn St. Hatfield, Pennsylvania United States of America

Transcription

1

2 2017 PRODUCT CATALOG Nelson Wire Rope Corporation 3051 Penn St. Hatfield, Pennsylvania United States of America Tel: Fax:

3 WARNINGS CONTENTS Every effort has been made to ensure that the information in this book is accurate. Nelson Wire Rope Corporation is not responsible for printing or clerical errors. The Nelson Wire Rope logo is a trademark of Nelson Wire Rope Corporation. Use of the Nelson Wire Rope Corporation logo for commercial purposes without the prior written consent of Nelson Wire Rope may constitute trademark infringement and unfair competition in violation of federal and state laws. Disclaimer and Terms of Use: Your reliance upon information and content obtained by you at or through this publication is solely at your own risk. Nelson Wire Rope Corporation assumes no liability or responsibility for damage or injury to you, other persons, or property arising from any use of any product, information, idea, or instruction contained in the content or services provided to you through this catalog. Reliance upon information contained in this material is solely at the reader s own risk. Nelson Wire Rope has no financial interest in and received no compensation from manufacturers of products mentioned in this book. Ancra, Apex Tool Group, Campbell, The Crosby Group, Gunnebo Johnson, Kenco, Kinedyne, Liftex, and Peerless Chain are trademarks of their respective companies in the USA and in other countries. Resources for lifting and safety use information: U.S. Department of Labor O.SH.A (800)-321-OSHA x6742 National Safety Council (800) Commercial Vehicle Safety Association (800) Web Sling & Tie Down Association (443) x110 ASME B30.9 (Slings) ASME B30.10 (Hooks for lifting) ASME B30.20 (Below the hook lifting devices) ASME B30.26 (Hardware) Safe working load, working load limit, and rated capacity, indicate maximum loads. Ratings apply to straight line pull unless otherwise specified. All ratings shown are based on new product used in normal operating conditions. Special considerations must be given to item selection when unusual conditions can be expected. Products are subject to wear, misuse, overloading, and deformation, which may result in a reduction of working load limit. We highly recommend that all products be regularly inspected. Worn or deformed items should be removed from service immediately. It is the responsibility of the user to determine the suitability of a product for any particular use. Nelson Wire Rope Corporation is not responsible for damages resulting from misuse or misapplication of any product made by Nelson Wire Rope Corporation or distributed by Nelson Wire Rope Corporation. Refer to all applicable industry, trade association, federal, state, and local regulation. Read all operating instructions and warnings carefully. Section 01: Wire Rope 06 General Purpose Wire Rope 06 Fiber Core Wire Rope 07 Compacted Crane Rope 08 Rotation Resistant Wire Rope 09 High Performance Crane Rope Section 02: Crane Accessories 12 Wire Rope Lubricant 12 Overhaul Balls 13 Crosby Wedge Sockets 13 Crane Blocks Section 03: Aircraft Cable 14 Galvanized Cable 15 Stainless Steel Cable 16 Stainless Steel Attachments 17 Sleeves and Tools Section 04: Cable Assemblies 18 Swage Socket Assemblies 19 Roll Off Cable Assemblies Section 05: Wire Rope Slings 20 Single Leg Slings 22 Multiple Leg Slings 24 Pipe Carrier Slings Section 06: Chain 26 Grade 30/43 Chain 28 Grade 70 Chain 30 Grade 100 Chain Section 07: Chain Slings 33 Single Leg Slings 34 Multiple Leg Slings 36 GrabiQ Chain Slings Section 08: Web Slings 40 Web Slings 42 Round Slings 43 Super Armour Slingers Section 09: Cargo Control 44 Ratchet Straps 45 Winch Straps 46 Winches & Winch Bars 47 Cargo Control Supplies 49 Interior Van Products Section 10: Rigging Hardware 50 Wire Rope Clips 52 Shackles 54 Long Reach Shackles 54 Klein Haven s Grips 55 Crosby Slide Loc 55 Standard D Rings 56 Eye Bolts 57 Swivel Hoist Rings 58 Snatch Blocks 59 Turnbuckles 60 Hoist Hooks 62 Shur Loc Hooks 63 Plate Clamps Section 11: Cordage 64 Braided Pulling Rope 65 Manella Rope 65 Polypropylene Rope 65 Nylon Rope Section 12: Chain & Cable Hoists 66 Beam Clamps 66 Manual Trolleys 67 Lever Hoists 67 Hand Hoists

4 GENERAL PURPOSE WIRE ROPE 6x19 Class 6x37 Class COMPACTED CRANE ROPE Flex-X 6 Flex-X 9 6x19 classification ropes provide an outstanding balance between fatigue and wear resistance. They give excellent service with sheaves and drums of moderate size. 6x37 classification ropes are more flexible but less abrasion resistant than the 6x19 classification. Each strand contains multiple small diameter wires. As the number of wires increases, flexibility increases. Fiber core rope provides increased flexibility over IWRC. While the strength is lower than IWRC, the flexibility may be preferred in certain applications. Flex-X 6 users receive superior performance and increased service life in many applications compared to the ropes they had previously employed. When compared to conventional six strand ropes, Flex-X 6 ropes provide greater surface area and more steel per given diameter. This increases rope stability and strength. This results in a longer service life and less sheave and drum wear. Flex-X 9 features compacted strands and swaging for extra drum crushing resistance and increased stability. Its high density strands deliver extra strength and resistance to abrasion. Flex-X 9 is manufactured with a dual compaction process to produce a compact cross-section with minimum voids and greater surface area on outer wires that contact drums, sheaves and the rope during operation. The high-density compacted strands minimize nicking at strand-to-strand contact points. Flex-X 9 was specifically designed for boom hoist applications where drum crushing is a challenge. Diameter in Inches Approximate Weight Per Foot EIP IWRC Nominal Breaking Strength Approximate Weight Per Foot EIP FC Nominal Breaking Strength 1/ / / / / / / / / / / / / / / / / / / / / / / Flex-X designs reduce drum scrubbing between the lead line and the previous wrap. The smooth contact creates less interference, less metal loss and wire deformation. The increased surface area of Flex-X can be seen in the comparison of the contact points of a standard 6x26WS and Flex-X as shown. Rope Diameter Approximate Weight Per Foot Flex-X 6 Flex-X 9 Nominal Breaking Strength Approximate Weight Per Foot Nominal Breaking Strength 3/ / / / / / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 7

5 ROTATION RESISTANT ROPE 19x7 8x19 19x19 Rotation resistant wire ropes are specially designed to resist spin and rotation while under load. SUPER FLEX-PAC (SFP) 35 SFP 35 is a rotation-resistant rope of high strength that can resist block twist in long falls. 35x7 19x19 EIP IWRC 19x7 EIP IWRC 8x19 EIP IWRC Rope Diameter Approximate Weight Per Foot Nominal Breaking Strength 3/ / / / / / / / / / / / / / / / / / / / / / / / / / Strands: 35 Wires per strand: 7 Core: WSC Standard grade(s): 2160 N/mm2 Lay: Right Regular Finish: Bright Superior Rotation Resistance the SFP 35 rope is the most rotation resistant rope manufactured by WW. Due to its rotation resistant properties, SFP 35 may be used with a swivel in both single part and multipart reeving. High Strength. WW s compaction process provides a high strength rope which exceeds EEIP nominal breaking strength. Application. SFP 35 excels in crawler and truck-type crane load lines, and tower crane hoist ropes. Flexibility. SFP 35 s multiple strand construction provides increased flexibility which improves service life and high speed spooling. The compacted multiple strand construction also reduces sheave and drum abrasion and provides excellent resistance to drum crushing. Diameter Approximate Weight Minimum Breaking Force inches mm lbs/ft. kg/m tons kn 5/ / / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 9

6 CASAR STARLIFT XTRA ENDURANCE DYFORM The latest high performance rotation-resistant rope designed and manufactured by CASAR Germany, a member of WireCo WorldGroup. 34LR 34XL 34MAX 35x7 CASAR Starlift XtraTM, the new high performance rotation resistant rope, was added to the CASAR product range to meet the highest Minimum Breaking Forces requested in the crane rope market. CASAR Starlift Xtra provides the user unique characteristics as a hoist rope. 34x7 Resistance to rotation Greatest resistance to rotation of all ropes in the rotation- resistant product range confirmed by Bridon s unique Twistcheck testing program. Resistance to bending fatigue Longer bend-fatigue life when compared with conventional rotation-resistant ropes confirmed by laboratory testing and extensive field experience. Resistance to crushing Excellent resistance to crushing and abrasion due to the rope s compact design and the Dyform strands recommended when multi-layer spooling is involved. Rotation Resistance (Non-Rotating) The balanced design of CASAR Starlift Xtra results in minimal torque under load, providing superior rotation resistance. Under a normal working load range, CASAR Starlift Xtra has virtually no tendency to rotate, making it ideal for both single-part and multi-part hoist systems and also for those involving long falls where rotation resistance is required. CASAR Starlift Xtra meets both the Category 1 requirements according to ASTM A1023 and the general guidance on the use of a swivel given in Annex A ISO Due to its superior rotation resistant properties, CASAR Starlift Xtra may be used with a swivel. Resistance to Wear The multi-strand design of CASAR Starlift Xtra combined with compacted strands and lang lay construction helps to maximize resistance to wear by greatly increasing wire and strand surface areas that contact sheaves and drums. Internally, the enhanced surfaces of the compacted strands help minimize strand-to-strand nicking between strand layers. This feature results in greater resistance to fatigue. Resistance to Crushing and Abrasion on Drums The characteristics of CASAR Starlift Xtra enhance its performance in multiple-layer spooling as well. The design of CASAR Starlift Xtra provides excellent resistance to both abrasion and scrubbing that occurs at kickover areas and crushing that occurs at the crossover points in multiple-layer drum spooling. The rope construction combined with the compacted strand design of CASAR Starlift Xtra results in a rope cross-section of very high density. These features provide increased resistance to drum-related wear. Rope Diameter in MM Approx Weight (lbs/ft) Minimum Breaking force (kn) Approx Weight (kn/m) Minimum Breaking force (tons of 2,000 lbs.) , , , , , , , , Reduced elongation Increased steel content and the Dyform process minimize elongation. Long service life Exceptional performance means less down time and more work time. Diameter Approximate Weight Minimum Breaking Force (tons) inches mm lbs/ft. 34 LR LR XL 34MAX 1/ / / / / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 11

7 CRANE ACCESSORIES CRANE ACCESSORIES Wire Rope Lubricant Diameter (Inches) Gallons per 1000 Feet Amount in Ounces 1/ / / / / / / Crosby S-421T Wedge Sockets Crosby Part Cable (Inches) Weight Each / / / / / Available in 12 oz. spray cans, 5 gallon pails, and 55 gallon drums 1 1/ Overhaul Balls Overhaul Ball Model Working Load Limit in Metric Tons OHB 3,2.20.C 3,2 OHB OHB OHB OHB OHB 12,5.45.C 12,5 OHB OHB Crane Blocks Range from ton. Fast reeving without removing your socket from the wire rope. High tensile side plates with integrated hand grips for positioning and stabilizing before catching load. Compact and multipurpose design. Swinging hook suspension for swiveling hook. please call for specific models or technical information OHB Range from 2-80 ton. Body in forged steel with becket on top for easily fitting on an open wedge socket or shackle. Hook in forged alloy steel with safety latch and first class trust bearing, including grease fitting. 12 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 13

8 GALVANIZED AIRCRAFT CABLE 7x7 7x19 Commercial grade and not for aircraft use. 7x19 is used when flexibility is a concern. 7x7 is for applications where extreme flexibility is not required. 7x7 Galvanized Rope Diameter Length on Reel in Feet Approximate Weight Per Reel Nominal Breaking Strength / / / / / / / , / , / ,700 7x19 Galvanized Rope Diameter Length on Reel in Feet Approximate Weight Per Reel Nominal Breaking Strength / , / , / , / , / , / , / , / , / , / , / , / , / , / , / , / , / , / ,400 7x7 Type 304 Rope Diameter STAINLESS STEEL CABLE Approximate Weight Per 1000 Foot 7x7 7x19 Nominal Breaking Strength / / /8 28 1,700 7x19 Type 304 Rope Diameter Approximate Weight Per 1000 Foot Nominal Breaking Strength / /8 29 1, / , / , / , / , / ,000 7x7 Type 316 Rope Diameter Approximate Weight Per 1000 Foot Nominal Breaking Strength / / /8 28 1,360 7x19 Type 316 Stainless steel cable is used in applications where greater cable corrosion resistance is required. Rope Diameter Approximate Weight Per 1000 Foot Nominal Breaking Strength /8 29 1, / , / , / , / , Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 15

9 STAINLESS ATTACHMENTS Stainless steel attachments provide corrosion resistance and durability and are ideal for marine, industrial and architectural wire projects. SLEEVES & TOOLS Our line of sleeves and tools are designed for quick and easy installation. For use in applications that do not require mechanically swaged sleeves. Stainless Thimbles Rope Diameter / / / / / / /8 Stainless Clips Rope Diameter / / / / / / /2 Aluminum # Oval Sleeves Copper # Cable / / / / /16 Aluminum Buttons Cable / / / / /16 Stainless Screw Pin Anchor Shackles Rope Diameter /4 1, /16 1, /8 2,000 Cable Cutter Cable cutters designed to cut up to 3/16 cable # /2 4, /8 6,000 Eye & Eye Stainless Steel Turnbuckles Jaw & Jaw Turnbuckle /8 x 6 1, /2 x 6 2, /8 x 6 3,500 Hand Swagers Will Swage /64 Only /16 Only /16-3/ /4 x 6 5, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 17

10 SWAGED SOCKET ASSEMBLIES Fitted with end terminations, including open or closed-type sockets for main pendants, and bridge sockets for intermediates and safety pendants. ROLL OFF CABLE ASSEMBLIES We offer several types of roll off cables for your trucks and equipment. Roll off cables can be ordered in any length, size, and with any of the attachments shown below. Single rope legs and open swage sockets Type Pear Link Type Master Link Type 11-SB-0 Swaged Button Type 11-CE-0 Cable End Single rope legs and open and closed swaged sockets Single rope legs and closed swage sockets Length of Sling Wire Rope Diameter Minimum Pendant Length Vertical Capacity 1/ / / / / / / / / / / Roll Off Container Strap Standard roll off cable assemblies are made using 7/8 6x25 or 6x36 EIPS IWRC Standard Wire Rope. The nominal breaking strength is 39.8 tons or 79,600 pounds. Length in Feet 3 x 5 4 x 5 18 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 19

11 SINGLE LEG SLINGS 6x19 Class 6x37 Class SINGLE LEG SLINGS 6x19 Class 6x37 Class C I.D. Code End Fitting 1 Standard Eye 2 Thimble Eye 3 Hook 4 Screw Pin Anchor Shackle 5 Crescent Thimble 6 Open Swage Socket 7 Closed Swage Socket 8 Pear Link 9 Master Link OSS CSS SB CE Sling I.D. Chart Open Spelter Socket Closed Spelter Socket Swaged Button Roll Off Cable End Wire Rope Diameter Galvanized Cable Laid Slings Sling Construction Width Length Rated Capacity (2000 lbs.) Eye in Inches Vertical Choker Basket Recommended Minimum Length 3/8 7x7x /2 7x7x /8 7x7x /4 7x7x /8 7x7x x7x Hidden Tuck Hand-Spliced Slings Wire Rope Diameter Rated Capacity (2000 lbs.) Eye in Inches Vertical Choker Basket Eye Width Mechanical Splice Flemish Eye Slings Eye Length Minimum Sling Length EIP IWRC 1/ / / / / / / / / / / Wire Rope Diameter Width Length 6x19 EIP Fiber Core Rope Rated Capacity (2000 lbs.) Eye in Inches Vertical Choker Basket Minimum Length 3/ / / / WARNING: Do not exceed rated capacities. Sling Capacity decreases as the angle from the horizontal decreases. Slings should not be used at angles of less than 30 degrees. 20 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 21

12 TWO LEG BRIDLE SLINGS Type FOUR LEG BRIDLE SLINGS Type x19 or 6x37 Class EIPS IWRC Rated Capacity (2000 lbs.) Rope Diameter 30 Degrees 45 Degrees 60 Degrees 1/ / / / / / / / / / x19 or 6x37 Class EIPS IWRC Rated Capacity (2000 lbs.) Rope Diameter 30 Degrees 45 Degrees 60 Degrees 1/ / / / / / / / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 23

13 PIPE CARRIER PRODUCTS An efficient way to handle concrete water and sewer pipe THE PIPE PICK Pipe Carrier Lifting Sling Pipe Carrier slings can be made to any length to fit the specific needs of your application. Each sling has a standard eye on one and, and a button on the other end. Button Length can also be adjusted per your request Wire Rope Diameter & Length /8 x /4 x /2 x 5 Tea Cup Pipe Carrier Model Minimum Pipe ID Capacity in Pounds CPP CPP CPP Rope Diameter Rated Capacity A (in.) B (in.) C (in.) D (in.) E (in.) F (in.) G (in.) / / / A quicker, safer, and cleaner way of handling precast concrete pipes No need to reach inside the pipe Conforms to applicable standards in compliance with OSHA regulations Low Profile Tea Cup Rope Diameter Rated Capacity A (in.) C (in.) H (in.) G (in.) / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 25

14 GRADE 30 PROOF COIL CHAIN Not for overhead lifting. GRADE 30/43 COMPONENTS Not for overhead lifting. Self Colored Chain Chain Feet for Half of a Drum Feet Per Pail Approximate Weight Per 100 Feet (lbs.) Working Load Limit / / , / , / ,650 Zinc Plated Chain / / , / , / ,650 Hot Dip Galvanized Chain / / , / , / ,650 Clevis Slip Hook (Latch) / / / / /8 Clevis Grab Hook / / / / / /8 Eye Slip Hook / / / / /8 Eye Grab Hook / / / / /8 GRADE 43 HIGH TEST CHAIN Self Colored Chain Chain In Inches Feet for Half of a Drum Not for overhead lifting. Feet Per Pail Approximate Weight Per 100 Feet (lbs.) Working Load Limit /4 400 n/a 75 2, / n/a 111 3, /8 200 n/a 157 5, /2 100 n/a 274 9,200 Cold Shut / / / / / /2 Quick Link / / / / / / /8 Twin Clevis /4-5/ / /16-1/2 26 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 27

15 GRADE 70 CHAIN & HARDWARE Not for overhead lifting. GRADE 70 CHAIN & HARDWARE Not for overhead lifting. Gold Plated Grade 70 Chain Chain In Inches Feet for Half of a Drum Approximate Weight Per 100 Feet (lbs.) Working Load Limit / , / , / , / ,300 Grade 70 Binder Chains Chain and Length Breaking Strength /16 x 10 4,700 18, /16 x 14 4,700 18, /16 x 16 4,700 18, /16 x 20 4,700 18, /16 x 25 4,700 18, /8 x 10 6,600 26, /8 x 14 6,600 26, /8 x 16 6,600 26, Clevis Grab Hook /8 x 20 6,600 26, /8 x 25 6,600 26, /16 4, /8 6, /2 11, Ratchet Type Load Binders Chain Min. to Max Maximum Take Up Clevis Slip Hook /16 4, /8 6, /2 11, /16 to 1/4 2, /16 to 3/8 7, /8 to 1/2 9, /2 to 5/8 13, /2 to 5/8 with 5/8 Slip Hook 13, /8 15, Lever Type Load Binders Clevis Slip Hook with Latch /16 4, /8 6, Chain Min. to Max Maximum Take Up /16 to 1/4 2, / /16 to 3/8 5, / /8 to 1/2 9, / /2 11, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 29

16 GRADE 100 LIFTING CHAIN Alloy chain is rugged, versatile, high-strength, low-weight chain manufactured from special analysis alloy steel. It is quenched and tempered before proof testing and the ultimate tensile strength is over twice that of ordinary steel chain. Tensile strength following heat treatment meets or exceeds all existing OSHA, Government, NACM and ASTM specification requirements. Chain In Inches Feet for Half of a Drum Approximate Weight Per 100 Feet (lbs.) Working Load Limit / , / , / , / , / ,300 Eye Grab Hook Eye Sling Hook Clevis Cradle Grab Hook / / / / / /8 GRADE 100 LIFTING COMPONENTS / / / / / / /2 Coupling Link /32 Clevis Grab Hook /32 Clevis Sling Hook /32 Clevis Shur Loc Hook Eye Shur Loc Hook Swivel Shur Loc Hook / / / /32-5/ /32-5/ /32-5/ / / / / / / / / / / / / / / / / / /8 30 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 31

17 CHAIN SLINGS All Nelson Wire Rope chain slings include a metal tag with sling length, diameter, serial number, and rated capacity. SOSL SOO SOS SOG of Chain (in.) (mm) Grade Chain s, Configurations & Capacities Single Leg Chain Sling (lbs.) Two Leg Chain Slings (lbs.) Three & Four Leg Chain Slings (lbs.) 9/ ,300 7,500 6,100 4,300 11,200 9,100 6,450 3/ ,800 15,200 12,400 8,800 22,800 18,600 13,200 1/ ,000 26,000 21,200 15,000 39,000 31,800 22,500 5/ ,600 39,000 32,000 22,600 58,700 47,900 33,900 3/ ,300 61,100 49,900 35,300 91,700 74,900 53,000 Grade 80 DOP Chain Sing (in.) Two Leg Chain Slings (lbs.) 3/8 9,300 7,600 5,400 SSLSL SSS SGS SGG Two leg chain sling with a masterlink at the top and lifting pins at the bottom. Pins come in either 1 diameter or 1-3/16 diameter. Check Pipe diameter before ordering WARNING: Do not exceed rated capacities. Sling Capacity decreases as the angle from the horizontal decreases. Slings should not be used at angles of less than 30 degrees. 32 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 33

18 TWO LEG CHAIN SLINGS FOUR LEG CHAIN SLINGS Grade 100 Chain Grade 100 Chain DOSL DOG DOS QOG DOS-A DOS-B QOSL QOS *Three and four leg chain slings can also be fabricated with A-style and B-style adjusters 34 Nelson Wire Rope Corporation tel: fax: Nelson Wire Rope Corporation tel: fax:

19 GRABIQ CHAIN SLINGS A Simpler, Lighter, Chain Sling System A totally new way to fabricate chain slings GrabiQ is an exciting new family of alloy chain sling components. Instead of the old one component does one job fitting, GrabiQ combines in a single component up to three separate functions. Figure 1 features a GrabiQ Master Grab, which serves as the master link, connecting link for two legs of chain, and shortening hooks for each leg, all in one fitting. Using traditional fittings to construct the same sling would require 7 top-of-the- sling components, instead of just one. Some of the new GrabiQ fittings are equally well suited for use as top assembly connectors or hooks at the bottom of a sling, adding even more flexibility for riggers. While the specific Working Load Limits vary, depending on size, slings fabricated from grade 100 chain and fittings are about 25% stronger than their grade 80 counterparts. Converting from grade 80 to GrabiQ will especially benefit users who can make use of the additional WLL without the expense of purchasing larger chain and fittings. The percentage of strength increase varies depending on the size. The Working Load Limit (WLL) gain for 3/8 is about 24 percent, while the WLL gain for 9/32 is more than 30 percent. All other sizes fall somewhere in between. More flexibility in chain sling uses When each GrabiQ leg is furnished with a chain pocket, the chain sling can be used for a much wider variety of loads, often reducing the amount of rigging required on site. The chain pocket can be used to either shorten a leg or create a leg loop. Some fittings are equally well suited for use at the top or bottom of a chain sling. For example, the GrabiQ C-Grab can be used at a top of the sling or at the bottom of the sling as an adjustable sliding choker. Quality standards: Grade 100 GrabiQ alloy steel chain and chain sling components are manufactured and tested in accordance with ASTM A973, A952, and A907 material standards. GrabiQ chain and components meet or exceed the safety standards as prescribed by ASME B30.9 & B30.10, and OSHA alloy steel chain sling regulations. All chain and every single component is proof- loaded to 2.5 times the Working Load Limit. The Swedish plants manufacturing GrabiQ products are certified to ISO 9001/ ISO 9002 Quality Standards. Gunnebo Lifting s quality management covers all aspects of production from raw material to delivered product. Fewer Components means less weight Most of the time, GrabiQ slings will be lighter than their grade 80 counterparts. Fewer components means less weight. Also, because grade 100 has a lifting capacity that is usually 25% higher than its grade 80 counterpart, the ratio of strength-toweight is greater, offering additional weight savings with GrabiQ. 36 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 37

20 38 Nelson Wire Rope Corporation tel: fax: Nelson Wire Rope Corporation tel: fax:

21 WEB SLINGS Flat Eye Sling One Ply Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 1 EE ,600 1,250 3,200 2 EE ,200 2,500 6,400 3 EE ,800 3,800 9,600 4 EE ,400 5,000 12,800 6 EE ,300 7,440 18,600 One Ply Reversed Eye Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 2 RE ,600 3,680 9,200 3 RE ,900 5,520 13,800 4 RE ,600 6,880 17,200 6 RE ,000 9,600 24,000 Reversed Eye Sling The Workhorse of all web slings. When application is continuous or abusive, Reversed Eye Slings will outlive all other sling types. Type RE slings have wear pads on both sides of the body and eyes. Twist Eye Sling Two Ply Web Slings Four Ply Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 1 EE ,200 2,500 6,400 2 EE ,400 5,000 12,800 3 EE ,300 7,440 18,600 4 EE ,500 9,200 23,000 6 EE ,500 13,200 33,000 Rated Capacity Two Ply Reversed Eye Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 2 RE ,700 6,160 15,400 3 RE ,600 9,280 23,200 4 RE ,500 11,600 29,000 6 RE ,400 13,920 34,800 Triangle Choker Sling Width (Inches) Part Vertical Choker Basket Endless Web Sling 1 EE ,200 4,960 12,400 2 EE ,400 9,920 24,800 3 EE ,600 14,880 37,200 4 EE ,000 17,600 44,000 6 EE ,000 26,400 66,000 One Ply Triangle/Choker Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 2 TC ,200 2,500 6,400 One Ply Endless Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 3 TC ,800 3,800 9,600 4 TC ,400 5,000 12,800 6 TC ,600 7,600 19,200 1 EN ,200 2,500 6,400 2 EN ,400 5,000 12,800 3 EN ,300 7,440 18,600 4 EN ,400 9,920 24,800 Two Ply Triangle/Choker Web Slings Two Ply Endless Web Slings Rated Capacity Width (Inches) Part Vertical Choker Basket 1 EN ,200 4,960 12,400 2 EN ,400 9,920 24,800 3 EN ,600 14,880 37,200 Rated Capacity Width (Inches) Part Vertical Choker Basket 2 TC ,400 5,000 12,800 3 TC ,900 7,200 17,800 4 TC ,000 9,600 24,000 6 TC ,000 13,000 34,000 4 EN ,000 17,600 44, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 41

22 ENDLESS ROUND SLINGS ARMOUR SUPER SLINGERS The first ever roundsling with nanotechnology Round Slings offer the user the ultimate in lifting security and rigging ease. Round Slings are constructed from a continuous loop of 100% polyester fiber. Each Round Sling is covered with a double polyester woven jacket to protect the load-bearing fibers from damage. Because the load-bearing fibers never come in contact with the load, they are protected from cuts, abrasions and ultraviolet degradation. Each sling has a tough, resilient tag for quick and easy identification. Super Slinger can be 15 times lighter than steel. Using Super Slingers can reduce the amount of manpower needed for the job, as well as the hours it takes to do the lift. A SS-3000 sling has a Vertical capacity of 300,000 lbs, and at a 60 foot length the sling would weigh 320 lbs. To reach the same capacity in wire rope the slings would have to be 4-1/8" diameter would weigh 2000 lbs. That means the Super Slingers weigh only 16% of what the wire rope sling would weigh! Advantages: Reduce cost with less total rigging weight Easy handling and storage Reduce risk of back and hand injuries Cover abrasion will not reduce capacity Provides a strong grip on loads Provides a tighter choke with an easier release Capacities are color coded Armour Super Slinger are made with a heavy duty nylon cordura cover for maximum protection, and a red internal jacket for easy inspection. Armour Super Slingers are RFID enabled to allow for fast and accurate sling identification. Part Sling Color Vertical Capacity Choker Capacity Basket Capacity Minimum Length Approximate Weight per Foot ENR 1 Purple 2,600 2,100 5, lbs ENR 2 Green 5,300 4,200 10, lbs ENR 3 Yellow 8,400 6,700 16, lbs ENR 4 Tan 10,600 8,500 21, lbs ENR 5 Red 13,200 10,600 26, lbs ENR 6 White 16,800 13,400 33, lbs ENR 7 Blue 21,200 17,000 42, lbs ENR 8 Orange 25,000 20,000 50, lbs ENR 9 Orange 31,000 24,800 62, lbs ENR 10 Orange 40,000 32,000 80, lbs ENR 11 Black 53,000 42, , lbs ENR 12 Black 66,000 52, , lbs ENR 13 Black 90,000 72, , lbs ENR 13S Black 100,000 80, , lbs Part Sling Color Vertical Capacity Choker Capacity Basket 90 Basket 60 Basket 45 Approximate Diameter Approximate Weight per foot SSA200 Blue 20,000 16,000 40,000 34,600 28, / SSA250 Blue 25,000 20,000 50,000 43, , / SSA300 Blue 30,000 24,000 60,000 51,900 42, / SSA400 Blue 40,000 32,000 80,000 69,200 56, / SSA500 Blue 50,000 40, ,000 86,500 70, / SSA600 Blue 60,000 48, , ,800 84, SSA700 Blue 70,000 56, , ,100 98, / SSA850 Blue 85,000 58, , , , / SSA1000 Blue 100,000 80, , , , / SSA1250 Blue 125, , , , , SSA1500 Blue 150, , , , , / SSA1750 Blue 175, , , , , / SSA2000 Blue 200, , , , , / SSA2250 Blue 225, , , , , SSA2500 Blue 250, , , , , / SSA2750 Blue 275, , , , , SSA3000 Blue 300, , , , , / SSA4000 Blue 400, , , , , SSA5000 Blue 500, ,000 1,000, , , SSA6000 Blue 600, ,000 1,200,000 1,039, , Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 43

23 RATCHET STRAPS Standard ratchet strap assemblies are made from polyester webbing with a heavy duty steel ratchet. WINCH STRAPS Rhino Straps supply greater durability, strength and abrasion resistance We offer a full line of 2, 3 and 4 winch straps. All winch straps are made from resin-coated polyester for minimum stretch and maximum wear resistance. These rugged straps provide the strength and durability demanded in flatbed tie-down requirements. Flat Hook Wire Hook Chain Extension 2 Inch Ratchet Straps Breaking Strength Rated Capacity Assembly Length in Feet End Fittings ,000 3, Flat Hook ,000 3, Flat Hook ,000 3, Chain Anchor ,000 3, Chain Anchor ,000 3, Wire Hook ,000 3, Wire Hook Inch Rhino Heavy Duty Ratchet Straps ,000 3, Flat Hook ,000 3, Flat Hook Inch Ratchet Straps ,000 5, Flat Hook ,000 5, Flat Hook ,200 5, Chain Anchor ,200 5, Chain Anchor Inch Ratchet Straps ,000 5, Flat Hook ,000 5, Flat Hook ,500 6, Wire Hook ,500 6, Wire Hook 14.6 Winch Strap with Flat Hook Strap Width Assembly Length in Feet Breaking Strength Rated Capacity ,000 3, ,000 3, ,000 4, ,000 4, ,000 5, ,000 5, Heavy Duty Winch Strap with Flat Hook ,000 3, ,000 3, Winch Strap with Delta Ring ,000 4, ,000 4, ,000 5, ,000 5, Winch Strap with Chain Anchor ,000 3, ,000 3, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 45

24 WINCHES & WINCH BARS CARGO CONTROL PRODUCTS Storable Winch This storable winch can hold up to 27 feet of a 4 winch strap. Standard Winch This standard winch can hold up to 24 feet of a 4 winch strap. Kinedyne Kwik Winder Designed to wind straps for storage in a toolbox # Strap Winder Designed to wind straps for storage in a toolbox # Fixed Winch # Sliding Winch # Fixed Winch # Sliding Winch # Combination Winch Bar Low Profile Bottom Mount Winch This low profile winch can hold up to 14 feet of a 4 winch strap # # Ratchet Winch Bar # Foot Winch Track 1/4 steel winch track designed for sliding winches # Coil Rack Designed to aid in supporting steel coils on flat bed trailers # Painted Standard Winch Bar # Portable Winch With 2 Set Screws This portable winch can hold up to 14 feet of a winch strap # Chrome Standard Winch Bar # Corner Protectors Designed for winch and ratchet straps in different sizes Steel 2 # Rubber 2 & 3 # Rubber 4 # Plastic 2 & 4 # Protective Sleeves Sleeves designed to protect ratchet and winch straps. Sold by the foot. 2 Protective Sleeve # Protective Sleeve # Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 47

25 CARGO CONTROL PRODUCTS INTERIOR VAN PRODUCTS Ratchet Cam Our most popular ratchet strap! # Durable Webbing Vinyl S Hooks Strong and Smooth Ratchet Anti-Fatique Rubber Grip Made in the USA 1 Heavy Duty Ratchet & Utility Straps Product Description Working Load Limit (lbs.) Utility Strap with Vinyl S Hooks - 6 ft Utility Strap with Vinyl S Hooks - 9 ft Utility Strap with Vinyl S Hooks - 15 ft Ratchet Strap with PVC Wire hook - 10 ft Ratchet Strap with Wire Hooks & D Ring - 16 ft Ratchet Strap with Vinyl S Hooks - 9 ft. (Blue Strap) Ratchet Strap with Vinyl S Hooks - 16 ft Ratchet Strap with Vinyl S Hooks - 15 ft. (Blue Strap) Logistic Straps With Spring Fittings Buckle Type Assembly Length in Feet Breaking Strength Rated Capacity Unit Weight Ratchet 12 3,000 1, Ratchet 16 3,000 1, Ratchet 20 3,000 1, Cam 12 2, Cam 16 2, Cam 20 2, Logistic Track Series E 12GA painted logistic track - 10 Ft. # Rubber Tarp Ties Durable, long lasting, and made in the USA come in boxes of 50 Strap Length Overall Length Polyethylene Tarps Two styles of polyethylene straps. Regular and heavy duty, which is a double ply tarp in Feet Regular (Blue) Heavy Duty (Green & Black) 10 x x x x x x x Saf-T-Lok Bars Descrption Aluminum ( ) Steel ( ) Retract-A-Bar ( ) Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 49

26 WIRE ROPE CLIPS WIRE ROPE CLIPS Minimum Clips Required Torque Turnback length Minimum Clips Required Torque Turnback length / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /4 Forged Clips / / / / / /2 Malleable Clips / / Method of Application: Stainless Steel Clips Minimum Clips Required Turnback length /6 2 2/ / / / / / / / / / / / /2 call 5/ call 3/ call 7/ call Turn back the specified amount of rope from the thimble. Apply the first clip one base width from the dead end of the rope 2. Apply the next clip as near to the loop as possible. Turn on the nuts but do not tighten 3. Space additional clips equally between the first two. Take up rope slack. Tighten all nuts evenly on all clips 50 Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 51

27 SHACKLES SHACKLES Capacities 1/3 thru 55 metric tons, grade 6. Forged - Quenched and Tempered, with alloy pins. Working Load Limit and grade 6 permanently shown on every shackle. Hot Dip galvanized or self colored. Fatigue rated. Shackles 25t and larger are RFID EQUIPPED. Capacities 1/3 thru 55 metric tons, grade 6. Forged - Quenched and Tempered, with alloy pins. Working Load Limit and grade 6 permanently shown on every shackle. Hot Dip galvanized or self colored. Fatigue rated. Shackles 25t and larger are RFID EQUIPPED. G-209 G-2130 Screw Pin Anchor Shackle G-209 S-209 Shackle Pin Diameter /3 3/16 1/ /2 1/4 5/ /4 5/16 3/ /8 7/ /2 7/16 1/ /2 5/ /4 5/8 3/ /4 3/4 7/ /2 7/ / / /2 1 1/8 1 1/ /4 1 3/ /2 1 3/8 1 1/ /2 1 5/ / /4 45 Bolt Type Safety Shackle G-2130 Shackle Pin Diameter /3 3/16 1/ /2 1/4 5/ /4 5/16 3/ /8 7/ /2 7/16 1/ /2 5/ /4 5/8 3/ /4 3/4 7/ /2 7/ / / /2 1 1/8 1 1/ /4 1 3/ /2 1 3/8 1 1/ /2 1 5/ / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 53

28 LONG REACH SHACKLES These shackles are designed for use in construction applications where a longer reach is needed to attach to pick points. Design factor of 5:1 Meets the requirements of ASME B30.26 Alloy Steel WLL forged on body Do not point load. The load should be evenly distributed over the entire pin to achieve full working load limit. CROSBY SLIDE LOC NEW PRODUCT Available in capacities from.5 to 3.2 metric tons Bail is Forged Alloy Steel Quenched and Tempered Bail swivels 360 degree Rated at 100% for 90 degree angle. Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit. Meets the Machinery Directive 2006/42/EC guidelines and is marked with CE accordingly. Replaceable bolts available, including longer bolts. Bolt specification for metric bolt is Grade 10.9 alloy cap screw to ISO Unique locking mechanism makes the lifting point well suited for quick attachment to load surface. No need for tools. Features QUIC-CHECK markings on bail to assist in knowing when device is ready for lifting. Shackle Pin Diameter /4 7/ /2 1 5/ Crosby Part Bolt Effective Thread Projection Length Weight of Each /8-16 x /2-13 x 1-1/ /8-11 x 1-5/ /4-10 x /8-9 x 2-1/ x KLEIN HAVEN S GRIPS - # Haven s Grips are designed for use when a light, compact grip is desired where conductor deformation is not a factor. Knurled eccentric jaw applies gripping pressure to 1/4" of cable area. Some models include a swing latch that holds cable securely in jaw. Recommended for messenger and guy strand and wire rope Series can be used for wire rope. Cable Capacity: 0.50'' Cable Diameter Range: 0.28'' to 0.75'' Maximum Safe Load: 5000 lbs. Minimum Cable Diameter: 0.125'' STANDARD D RINGS Diameter Inside Length And Width Working Load Limit (lbs) /2 2-1/4 x 2-1/2 4, /8 3 x 3 6, /4 3 x 3 9, x 4 15, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 55

29 EYE BOLTS SWIVEL HOIST RINGS We offer a selection of popular swivel hoist rings from Crosby. If you require a specific swivel hoist ring that is not listed below, we will special order them for quick delivery. Machinery Eye Bolts Thread /4 x /16 x 1 1/ /8 x 1 1/4 1, /2 x 1 1/2 2, /8 x 1 3/4 4, /4 x 2 6, /8 x 2 1/4 7, x 2 1/2 9, /4 x 3 15, Our selection of standard Crosby swivel hoist rings fits many applications. However, if the swivel hoist rings below do not meet your requirements and you cannot find a match on Crosby s website, we offer custom made swivel hoist rings. Please provide the specifications you require and we will quote. Depending on complexity and quantity, there is normally a 2 to 3 week completion period. Shoulder Eye Bolts Diameter & Shank Length (in.) Work Load Limit (lbs.) Thread Length (in.) Inside Diameter of Eye (in.) /4 x /4 x /16 x 2 1/4 1, /16 x 4 1/4 1, /8 x 2 1/2 1, /8 x 4 1/2 1, /2 x 3 1/4 2, /2 x 6 2, /8 x 4 5, /8 x 6 5, /4 x 4 1/2 7, /4 x 6 7, /8 x 5 10, x 6 13, x 9 13, /4 x 8 21, Crosby Part Torque in Feet per Pound Bolt Thread Projection Length /16-18 x /8-16 x /2-13 x /2-13 x /8-11 x /8-11 x /4-10 x /4-10 x /4-10 x /4-10 x /8-9 x /8-9 x x x /4-7 x /2-6 x /2 x /2-4 x x /2-4 x Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 57

30 SNATCH BLOCKS TURNBUCKLES Drop forged hot dip galvanized Standard Features Rugged and reliable Easy-open side plates 4 to 1 design factor Metric Rated Large hand nuts Retainer on latch pin Bronze bushing Steel J Latches Snatch Block with Swivel Hook Johnson Model in Metric Tons Rope Diameter in Metric Tons JL3-5 3 & JL JL & JL JL30 30 Sheave Diameter Cable Weight of Each SB2S3BH 2 3 5/16-3/ SB4S4BH 4 4 3/8-1/ SB4S6BH 4 6 3/8-1/ SB4S8BH 4 8 3/8-1/ SB8S6BH 8 6 5/8-3/ SB8S8BH 8 8 5/8-3/ SB12S8BH /4-7/ SB12S10BH /4-7/ SB12S12BH /4-7/ SB15S10BH /4-7/ SB15S12BH /4-7/ SB15S14BH /4-7/ SB20S12BH / SB20S14BH / SB20S16BH /8 146 Diameter & Take up Hook & Hook Hook & Eye Eye & Eye Jaw & Eye Jaw & Jaw Eye & Eye Jaw & Eye Jaw & Jaw Hook & Hook Hook & Eye 1/4 x /16 x 4 1/ /8 x ,200 1,000 1/2 x ,200 1,500 1/2 x ,200 1,500 1/2 x ,200 1,500 5/8 x ,500 2,250 5/8 x ,500 2,250 3/4 x ,500 3,000 3/4 x ,200 3,000 3/4 x ,200 3,000 3/4 x ,200 3,000 1 x ,000 5,000 1 x ,000 5,000 1 x ,000 5, /4 x ,200 5, /4 x ,200 5, /4 x ,200 5, /2 x ,400 5, /2 x ,400 5, /2 x ,400 5, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 59

31 HOIST HOOKS S-4320 Latch Kit SS-4055 Latch Kit Carbon Eye Hook Capacity Inside Diameter of Eye Throat Opening Corresponding Latch ID /4 3/4 7/8 D /32 31/32 F /2 1 1/8 1 G /4 1 1/8 H / /32 I /16 J Alloy Eye Hook Capacity Inside Diameter of Eye Throat Opening Corresponding Latch ID /2 29/32 31/32 F /8 1 G /4 1 1/8 H / /32 I /16 J /16 2 1/16 K /32 2 1/4 L /2 3 N S-4320 SS-4055 Carbon Capacity Alloy Capacity Corresponding Latch ID /4 1 D /2 F /2 2 G H I J /2 11 K L N 2 Ton Sorting Hook # Alloy Swivel Hook Capacity Inside Diameter of Eye Throat Opening Corresponding Latch ID /4 7/8 D /2 29/32 31/32 F /8 1 G /4 1 1/8 H / /32 I /16 J /16 2 1/16 K /32 2 1/4 L /2 3 N Weld-On Bucket Hook Rated Capacity Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 61

32 SHUR-LOC HOOKS Crosby Shur-Loc Hooks are Forged Alloy Steel - Quenched and Tempered. Recessed trigger design is flush with the hook body, protecting the trigger from potential damage. Positive Lock Latch is Self-Locking when the hook is loaded. Suitable for use with Grade 100 chain, Grade 80 chain, and wire rope slings. S-1316 Shur-Loc Eye Hook Wire Rope Wire Rope W.L.L Chain Chain W.L.L /16 4,200 1/4-5/16 5, /2 5,600 3/8 8, /8-3/4 12,400 1/2 15, /8 16,600 5/8 22, ,000 3/4 35, S-1326 Swivel Style Hook Wire Rope * Wire Rope W.L.L Chain Chain W.L.L Suitable for infrequent non-continuous rotation under load /16 4,200 1/4-5/16 5, /2 5,600 3/8 8, /8-3/4 12,400 1/2 15, /8 16,600 5/8 22, ,000 3/4 35, Crosby IPU10 Universal Clamps Part PLATE CLAMPS Jaw Opening /2 0-5/ / / / Crosby IP10/A Vertical Clamps *Automatically clicks on to the material as soon as the plate is placed on the clamp Part Part Crosby IP10 Straight Eye Clamps Jaw Opening Jaw Opening call call call /2 0-5/ / / / S Swivel Style Hook with Bearing Wire Rope * Wire Rope W.L.L Chain Chain W.L.L Suitable for frequent continuous rotation under load /16 4,200 1/4-5/16 5, /2 5,600 3/8 8, /8-3/4 12,400 1/2 15, /8 16,600 5/8 22, Crosby IPNM10N Vertical Clamps Part Jaw Opening call / call call Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 63

33 BRAIDED CABLE PULLING ROPE High force composite double braided rope with hand spliced eyes on both ends. Standard Length in Feet Comes on a heavy-duty Amish wood spool for smooth dispensing from a cable pull stand Constructed of low-stretch polyester that will not snap back when load is relieved, eliminating the risk of serious injury Meets 4 to 1 standard for tensile strength, ensuring safety in high-tension commercial and industrial applications Compatible with most pulling machines for increased ease of pulling Slick fabric is easy on the hands and slides through rough areas with ease Cable lubrication recommended for increased viscosity in high traction areas Break Strength Weight Per Reel / ,510 2, / ,510 2, /2 1,200 2,510 2, / ,070 3, / ,070 3, /16 1,200 3,070 3, / ,830 3, / ,830 3, /8 1,200 3,830 3, / ,430 6, / ,430 6, /4 1,200 6,430 6, / ,535 7, / ,535 7, /8 1,200 7,535 7, ,050 10, ,050 10, ,200 10,050 10, / ,525 12, / ,525 12, /8 1,200 12,525 12, Manila Rope Nylon Rope Standard Length in Feet Standard Length in Feet Weight of Reel Weight of Reel Breaking Strength Breaking Strength /4 1, / / , / , / , / , ,100 1,160 Polypropylene Rope Standard Length in Feet SYNTHETIC ROPE Weight of Reel Breaking Strength / , / , / , / , / , / , / , / , / ,500 1, ,000 2, / , / , / , / , / , / , / , / ,400 1, / ,200 1, ,000 2, Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 65

34 CABLE HOISTS & OVERHEAD PRODUCTS CHAIN HOISTS Cable Hoist Single Line Capacity Lift in Feet Double Line Capacity Lift in Feet , x x , , , , , , , , /2 Beam Clamp Capacity Grip Range Manual Trolley Capacity Flange Width Shipping Weight / Lever Chain Hoist Capacity Standard Lift in Feet / / / / / / / / Hand Chain Hoist Capacity Lift in Feet Minimum Distance Between Hooks Shipping Weight / / / / / / / / / / / / / / / / / / / / / Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 67

35 SERVICES Here at Nelson Wire Rope, we offer a variety of services for our customers including: On Site Sling Inspections: We will send one of our product specialists to your job site to inspect any or all of your wire rope and chain slings. We will check each sling for damage and we will flag any slings that should be taken out of operation or repaired before used under load. - Sling Repairs: If any of your slings or assemblies appear to be damaged, we will inspect them and replace any components that are no longer safe to use. You can also send in hooks and components used on previous assemblies and slings to reduce costs. - Testing Service: If you would like your slings tested, we have a Proof Testing machine designed to pull a sling to twice its rated capacity. This ensures that the sling was made properly and is safe for use in the field. Certifications are provided for your records. - Truck Delivery Service: We offer full time delivery service for orders that are too large, too heavy, or too expensive to ship via UPS. Our primary delivery area includes Pennsylvania, New Jersey, and Delaware. If an order needs to be shipped outside of the Tri-State area, we will also ship via common carrier. 68 Nelson Wire Nelson Rope Corporation Wire Rope Corporation tel: fax: sales@nelsonwirerope.com Nelson Wire Rope Corporation tel: fax: sales@nelsonwirerope.com 69

36 Nelson Wire Rope Corp Penn St. Hatfield, PA USA Tel: Fax: