RESINIZE FINISH APPLICATION INSTRUCTIONS
|
|
- Candice Martin
- 6 years ago
- Views:
Transcription
1 RESINIZE FINISH APPLICATION INSTRUCTIONS
2 Directions for Resinize Finish You just need a few things to start: fine-grain sandpaper (220 grit) foam roller and paintbrush (depending on your project - see instructions below) a clean paint tray and clean paint stir stick protective gloves and a clean cloth A paintbrush is necessary if your project involves recessed surfaces, or surfaces that are difficult to reach. Examples are grout, moldings, and sharp angles. Buy a paintbrush whose size is suited to those surfaces. Some projects may require painter s tape and a drop cloth. For surfaces that can get hot, like radiators and heated floors, turn off the heat several hours before application, so the surface is cool to the touch when applying Resinize. Please read these directions all the way through before beginning. Don t skip any steps or you won t get the best results with the Resinize system. Do not apply on flexible surfaces, plastic or silicone. Do not use outdoors. Store Resinize in a dry place, above the freezing point and below 95 F.
3 Surface Preparation 1. Lightly sand the surface with fine-grain sandpaper. (220 grit) 2. Wipe the surface clean with a dry cloth after sanding. Shake dust off as you clean. Removing all surface dust and particles is critical to a smooth Resinize finish. 3. Close doors and windows in the room to avoid dust/particles settling onto the surface. Resinize Help
4 Application Inside the Resinize Finish container you will find two smaller containers labeled Component A and Component B that you will mix together in the larger Finish container. DO NOT THROW IT AWAY! Check the inside of the large Resinize container to make sure it is clean and dust/dirt free. Once the smaller containers are mixed you will have approximately 90 minutes to use the product before it begins to harden, so don t mix the components until you are ready to Resinize. BEFORE AFTER
5 1. Open Component A and carefully pour all of it into the large container. A 2. Stir well for 1 minute with a clean paint stick, until smooth and consistent. 1min 3. Open Component B and pour all of it into the large container; scrape Component B carefully with the paint stick to ensure no product remains stuck at the bottom /sides. B 4. Stir the mixture well for 1 minute until fully blended, smooth and consistent. 1min 3-5min 5. Allow the mixture to stand for 3-5 minutes,then pour into the paint tray. Resinize Help
6 6. Apply a thin layer of Resinize Finish with a very lightly loaded foam roller or paintbrush within 90 minutes of mixing. When applying to tiles, cover both the tile surface and the grout. If the grout is recessed or can not be reached with the roller, first use the paintbrush to apply Resinize to the grout and then apply to the remaining surface with the roller. 7. After applying a coat of Resinize Finish, make the roller as dry as possible by wiping any remaining product onto the paint tray. Then, go over the surface with parallel strokes this will smooth and stretch the patented Resinize Finish material for a smooth and clean look. 8. Clean all equipment with warm water within 90 minutes 9. For extra durability where surfaces get a lot of use or are exposed to a lot of water - such as a bathtub, shower, sink, floor we recommend a second layer be applied after 4 hours. This will require an additional container of Resinize Finish. Resinize Help
7 10. Keep as much dust and particles as possible out of the room for 12 hours; dust won t adhere to the surface after that. It will be dry to the touch after 24 hours and resistant to prolonged immersion after 72 hours (at 50 ). The surface will be fully hardened after 4 days. Do not expose the refinished surface to detergents or cleaning products until then. 11. For surfaces exposed to a great deal of water, use silicone caulk in joints and seams after 24 hours. BEFORE AFTER
8 THANK YOU! Distributed by Sipan LLC 104 Crandon Blvd, Suite 412 Key Biscayne FL Made in Italy Under license of U.S. Patent No. 8,592,038
ProAir Clear LV 2 Pack
Description The Lesonal Pro Air LV Clear Air Dry 2 PK Clear is an acrylic urethane clearcoat for use over Lesonal WB or SB Basecoat and intended for ambient cure conditions. This Clear offers excellent
More information3M DICHROIC Glass Finishes
3M DICHROIC Glass Finishes DF-PA DF-PA Chill Chill & & DF-PA DF-PA Blaze Blaze Doc TypeInstallation Product #Guide (opt.) Revision D, April 2018 Product Description 3M DICHROIC Glass Finish DF-PA (the
More informationFILE - RE CAULKING WINDOWS AND DOORS EBOOK
23 June, 2018 FILE - RE CAULKING WINDOWS AND DOORS EBOOK Document Filetype: PDF 492.45 KB 0 FILE - RE CAULKING WINDOWS AND DOORS EBOOK How Often Do I Need to Caulk Doors, Windows. The houses in our area
More informationINSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.)
INSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.) The PT 11 bumper is made from a high quality, non marking EPDM rubber. This
More informationHandle the film very carefully. As with aluminum foil, once creased, the film will remain creased.
RECOMMENDED TOOLS: Bottled water (not tap water) Spray bottle Squeegee or squeegee card Break-away utility knife (for cutting film) Single-edged razor blade (for cleaning glass) Ruler or tape measure Soft,
More informationweber.cote Pool Paint
weber.cote Pool Paint weber.cote Pool Paint weber.cote Pool Paint is a cement-based, integrally coloured, waterproof finish, specifically formulated for the revamping of marble plastered pools. Applied
More informationSurfboard Repairs Chapter 7
Surfboard Repairs Chapter 7 The Complete Surfing Guide for Coaches - Bruce "Snake" Gabrielson Repair Problems Boards continuously get bumped, hit rocks, break fins, get dropped, and many other things that
More informationAutocryl. This product is not for sale to Vehicle Refinishers in the EU, who need to comply to the Directive 2004/42/EC
Description Two-pack acrylic enamel for passenger cars, commercial vehicles and equipment. For new work and repairs. This product is not for sale to Vehicle Refinishers in the EU, who need to comply to
More informationAdvantages of ALEXIT BladeRep
Advantages of ALEXIT BladeRep Product can be used individually or as a complete system User-friendly packaging for repairs of any size Easy mixing and application Specifically designed for blade repair
More informationVacuum Bagging Wings Instruction Manual Purdue University
Vacuum Bagging Wings Instruction Manual Purdue University Note: Do not leave the vacuum pump running unattended! Revision: Original Release 10/31/15 Vacuum bagged wings are quick to build, light weight,
More informationMORE SPEED LESS FUEL APPLICATION MANUAL
MORE SPEED LESS FUEL APPLICATION MANUAL PROPSPEED: Each 1 litre kit contains 2 x 240ml etching primer, 2 x 60ml etching primer hardener and 1 x 400ml topcoat PROPPREP: Each box contains 10 individual Propprep
More informationUse suitable respiratory protection Contains acrylic resins, xylene and other ingredients. When mixed, it also contains isocyanates.
Description LV The LV is an acrylic urethane clearcoat for use over Autowave and Autobase Plus and is intended for ambient/forced dry conditions. This clear offers excellent resistance to surface contamination
More informationDamage Control/Luminous Shipboard Markings
3 Damage Control/Luminous Shipboard Markings 3M Diamond Grade Reflective Sheeting 3M Reflective Pipe Markings 3M Luminous Film U.S. Navy Shipboard Label Application Instructions August 2005 Replaces Instructions
More informationHow to repair a dinged windsurf board
How to repair a dinged windsurf board VERY Important: before the repair, let the board dry out for at least a day in the hot sun. Be sure to read "preparation" below. Repair of a small (1/2") hole in the
More informationLAB Chip Lid Molding LAB PROCEDURE
LAB Chip Lid Molding LAB PROCEDURE The purpose of this lab is to expose the student to a lab-on-a-chip fabrication technique. The student will utilize polydimethylsiloxane (PDMS) poured in four Petri dishes
More informationPart II. Under Construction Station Instructions. Lab Station A - Blue Print: There is O 2 Here!
Lab Station A - Blue Print: There is O 2 Here! Description: In this lab, you will consider the problem: What happened to the oxygen in the air we breathed in? Air that enters the body upon inhalation contains
More informationAutocryl Plus LV mm bar at the air inlet. 1-3 minutes at 20 C 1-3 minutes at 20 C
Description Two component, high Solid mixing machine based, polyester/acrylic topcoat specifically designed for the refinishing of passenger cars. The system has a VOC content of 420 g/liter and is supported
More informationPRODUCT BULLETIN AUTOMOTIVE FILMS FPP Auto A CONTENTS
PRODUCT BULLETIN AUTOMOTIVE FILMS FPP.7.3.2.Auto A 07.07 APPLYING AND REMOVING Solar protection film AUTOMOTIVE FILM MATERIAL REQUIRED PULVITRE (11-litre vaporiser) MARJO flexible squeegee MARBLEU soft
More informationTOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual
TOURNAMENT ICE 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual Thank you for purchasing a Gold Standard Games product. All of us at Gold Standard Games want you to be
More informationGLIDING NEW ZEALAND ADVISORY CIRCULAR MYLAR SEALS. This is an Uncontrolled Document. Issued September 2004
GLIDING NEW ZEALAND ADVISORY CIRCULAR MYLAR SEALS This is an Uncontrolled Document Issued September 2004 Holder s Name: Address: COPYRIGHT 1999 GLIDING NEW ZEALAND INC. No part of this Advisory Circular
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More informationSTUDY GUIDE A Day By Day Course Refreshment Quiz To Ensure That You Make The Most Out Of Your Rod Building Class
DAY ONE: 1) Why would you want to build your own fishing rod? a. It s fun and rewarding b. You can customize your rod to your needs c. You can save money d. All of the Above 2) The main part of a fishing
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationAliphatic Resin Wood Glue. 18" Fabric Parachute Part #PNC50 Part # Part #11700 Part #J0016. Launch Lug
ADANCED * What you will need to build the Quest High-Q Hobby Knife * Straight Edge Pencil Aliphatic Resin Wood Sanding Sealer & Brush Spray Paint Parts and exploded view of the Quest High-Q Nose Cone 18"
More informationPD100 White, PD200 Black Low VOC Acrylic Polyurethane Topcoat
PD100 White, PD200 Black Low VOC Acrylic Polyurethane Topcoat PRODUCT DESCRIPTION PRODUCT DATA SHEET PRISM Direct-To-Metal(DTM) Urethane Topcoat is a premium two-component acrylic polyurethane system designed
More informationPORTABLE GAMING TERRAIN BOARD
TM PORTABLE GAMING TM Age TERRAIN BOARD 9+ Safety First! Use eye protection, always! Use ear protection with loud power tools Stay with kids while they work! Follow tool manufacturers safety guidelines
More informationSPECIAL THANKS TO THE FOLLOWING PEOPLE FOR THEIR HELP IN THIS PROJECT!
The Viper Mark VII is the state of the art fighter of the Colonial Fleet. It is sleeker and more modern than the Viper Mark II. The Mk7 is designed for both space and atmospheric environments and is also
More informationApplication & Care Reflexite V98 Conformable Graphic Sheeting For EMS Vehicle Graphic Applications RSA2340
Table of Contents General Information... 2 BEFORE APPLICATION... 2 STEP 1: TEMPLATING... 2 STEP 2: CUTTING... 2 STEP 3: SUBSTRATE PREPARATION... 3 STEP 4: SURFACE CLEANING... 3 STEP 5: APPLICATION TEMPERATURE...
More informationPRODUCT DATA SHEET. Advanced Industrial Coatings 2.1 VOC Epoxy Primer AIP302 Gray, AIP303 White PERSONAL PROTECTION SURFACE PREPARATION
Gray/ White s are a high-solid, direct to metal epoxy primer offering excellent performance properties and is easily topcoatable. Gray/ White can be used with a wide range of topcoats and are considered
More informationother tables and stations. A plexiglass sheet was placed on a table top to provide the smooth flat surface to lay up the fiberglass on.
Fiberglassing After hot wire cutting our four airfoils for testing, it was decided that greater strength was needed. The foam airfoils do not have the required strength to withstand the forces of the wind
More informationAutoclear Superior Pack FOR PROFESSIONAL USE ONLY
Description A 2 Pack version of Autoclear Superior 250, designed for use over Autowave and with the Manual Proportioning Unit. Consisting of two clearcoats and one dedicated hardener. Autoclear Superior
More informationNotes for Soldiers M4/M16 Weapon Painting 101. Step One: Gather the materials
Notes for Soldiers M4/M16 Weapon Painting 101 Presented here are the official Project Manager Soldier Weapons instructions for those Soldiers who have the green light to dress out their M4/M16 with paint
More informationD8126 EU-142. CERAMICLEAR Mar and Scratch Resistant Clearcoat. Preparation of Substrate: Required Products. Product Description:
CERAMICLEAR Mar and Scratch Resistant Clearcoat Product Description: CERAMICLEAR is a nano-technology, mar and scratch resistant, high solid clearcoat. This clear is specifically designed for the repair
More informationPanoptix PS51-TH FrontVü/LiveVü Thruhull
Panoptix PS51-TH FrontVü/LiveVü Thruhull Transducer Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide in the chartplotter or fishfinder
More informationCarving a Custom Seat
Carving a Custom Seat Seat Carving your own seat from mini-cell, high-density foam is really quite simple and has proven to be more comfortable than any commercially produced seat and often more reasonably
More informationBefore you begin your job you will need: Tiling Hints: Factory Tile:
Before you begin your job you will need: 1. Solvent = Alcohol or Acetone 2. Pencil 3. Single edge razor blades 4. Small water pail 5. Liquid dish soap 6. Role of paper towels 7. Caulking gun 8. Use a wooden
More informationGeneral Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits. Needed Items for Assembly
General Build Instructions for Mach 1 BT50 and BT55 Single Fin Kits 60-80 grit sandpaper Hobby knife Tape measure Scissors CA Super glue 30-minute epoxy 5-minute epoxy Masking tape 1/16 drill bit Needed
More informationPACKAGING: Component A W-THANE HBA CD (2,7 L) Component B W-THANE 5057 CD (0,9 L)
W-THANE HBA 851 PRODUCT DESCRIPTION: INTENDED USES: Bicomponent polyester glossy finishing paint, high solids per volume. Product developed to compose an anticorrosive protection system, high impermeabilization
More informationTECHNICAL DATA SHEET
716 South Columbus Avenue Mt. Vernon, NY 10550 Voice: (914) 699-3030 Fax: (914) 699-8527 TECHNICAL DATA SHEET SERIES 599-B3755 is a new sprayable silver-coated copper conductive coating for use on plastic
More informationThe Incredible Hull: Slip Sliding Away
Title: The Incredible Hull: Slip Sliding Away (Friction & Motion) Grade Level (s): 7-8 Introduction:Our common experience is that objects in motion do not often stay in motion. In real life when we move
More information3M Window Film Installation Film-to-Glass Recommendation Table
Film-to-Glass Recommendation Table The following table is meant to be used as a guide to provide for improved installation quality and minimal confusion. We have seen that installing a film designed for
More informationNotes for Soldiers Weapons Painting 101
Program Executive Office Soldier Strategic Communications Office Debi Dawson 703-704-2802 debi.dawson@us.army.mil Notes for Soldiers Weapons Painting 101 On 1 April, TACOM Life Cycle Management Command
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationMOTORWORKS SUBMARINE MODIFICATIONS
MOTORWORKS SUBMARINE MODIFICATIONS PART I STANDARD SUBMARINE OPERATION AND SETUP NO MODIFICATIONS. IF YOU WISH TO MODIFY YOUR SUBMARINE FOR DEEP OPERATIONS (BELOW 3 METERS) SKIP TO PART II PLEASE FOLLOW
More informationDesoprime. HS Primers. CA 7700 Series Application Guide. Where Smart Solutions Take Flight
Desoprime HS Primers CA 7700 Series Application Guide Where Smart Solutions Take Flight Use Desoprime HS CA 7700 series primers are high solids, low VOC (< 350 g/l), epoxy primers used on aircraft exterior
More informationTips for protecting your equipment Belay devices, descenders
Tips for protecting your equipment Belay devices, descenders You too can help prolong the lifetime of your products. To succeed in this challenge, several aspects must be taken into account: product usage
More informationAvery Dennison Instructional Bulletin 1.4 Application Methods for Pressure Sensitive Adhesive Films
Rev. 2 (April 2016) Avery Dennison Instructional Bulletin 1.4 Application Methods for Pressure Sensitive Adhesive Films Introduction Avery Dennison pressure sensitive adhesive films are available in a
More informationREPAIR MANUAL. Materials
REPAIR MANUAL Materials Balsa: Raw material for FST (Future Shape Technology series) and HELIUM rails or parabolic stringers. It is what gives our unique product its excellent performance characteristics.
More informationEquipment. Box Equipment PROTECTION FROM ACCIDENTS PROTECTION FROM CONTACT. Running Shoes
Box Equipment Equipment PROTECTION FROM ACCIDENTS Running Shoes Select shoes for grip, ankle support and protection and match with the player s age and weight and level of play. Examples would be a high
More informationGluing Guide QCS Oval & Quick Cuff
Gluing Guide QCS Oval & Quick Cuff General information SI TECH has an extensive background and history in the development and design of premium drysuit components that dates back to the early 1960 s. This
More informationHow to Weather and Ballast Track
How to Weather and Ballast Track Presented by Jeffrey Jarr Weathering Track What is a train track comprised of? Weathering Track What does real weathered track look like? Weathering Track What does real
More informationExxtacy. Repair and Tuning Manual. Exxtacy Construction Basics
1 of 20 Exxtacy Repair and Tuning Manual Construction Basics D Cell Repair Rib Repair Tuning Exxtacy Construction Basics The Exxtacy is built with carbon fiber and Kevlar/Aramide honeycomb. The Exxtacy
More informationActivity Instructions
Polymer Bouncy Balls Activity Instructions Part I - Making Latex Bouncy Balls per group or student: liquid latex measuring spoons water vinegar The following steps will make one liquid latex ball. Pour
More informationRefinishing two carbon fiber masts
Refinishing two carbon fiber masts Originally re-finishing the masts was going to be Meps' project instead of mine, but it got out of hand. Let me start with a disclaimer: You would all probably like reading
More informationPREPARATION & APPLICATION OF S1125 ADHESIVES
S1125 ADHESIVE Code of Practice ELE-3COP-604 8 th Sep 2017 Class I PREPARATION & APPLICATION OF S1125 ADHESIVES ELE-3COP-604 TE Raychem S1125 Adhesives ELECTRONIC APPROVAL, NO SIGNATURES WILL APPEAR. IF
More informationPre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender
Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and
More informationBoard Glassing Chapter 6
Board Glassing Chapter 6 The Complete Surfing Guide for Coaches - Bruce "Snake" Gabrielson Glassing Guidelines Like shaping, there is probably any number of ways to successfully glass a blank. Yet there
More informationWet Lamination of Dry Film Photoresist for the Hobbyist
Wet Lamination of Dry Film Photoresist for the Hobbyist By Adam Seychell Updated: 10. September 2009 Table of Contents Introduction...2 Equipment List...3 Squeegee Board...4 The Procedure...5 Cut photoresist
More informationCOMPACTING SPECIMENS USING THE TEXAS GYRATORY COMPACTOR (TGC) PART I COMPACTING SPECIMENS USING THE TGC. Test Procedure for
Test Procedure for COMPACTING SPECIMENS USING THE TEXAS GYRATORY COMPACTOR Texas Department of Transportation TxDOT Designation: Tex-206-F Effective Dates: May 2008 May 2009. 1. SCOPE 1.1 Use Part I of
More informationAutoclear Mix & Matt
Description is a three component matting finish for application over either Autowave or Autobase Plus in National Rule markets. The desired gloss level can be achieved by mixing the Low Gloss and Semi-Gloss
More informationSeamless Acoustical Plaster Solutions
Seamless Acoustical Plaster Solutions A seamless acoustical plaster solution The Fade system is a high quality plastering solution that absorbs unwanted noise in a wide range of environments. As an acoustic
More informationVersatile, user friendly all glass sliding revolving door w26-c Maintenance Instructions and Directions for Use
Versatile, user friendly all glass sliding revolving door w26-c Maintenance Instructions and Directions for Use Important guidelines for specialist retailers and end users Please read carefully and bear
More informationCOMPACTING SPECIMENS USING THE TEXAS GYRATORY COMPACTOR (TGC) PART I COMPACTING SPECIMENS USING THE TGC. Test Procedure for
Test Procedure for COMPACTING SPECIMENS USING THE TEXAS GYRATORY COMPACTOR Texas Department of Transportation TxDOT Designation: Tex-206-F Effective Dates: June 2009 July 2009. 1. SCOPE 1.1 Use Part I
More informationMICRO - DLG. This kit should only take 30 minutes to compile, very simple and quick.
MICRO - DLG This kit should only take 30 minutes to compile, very simple and quick. You will need: Hot Glue ( small tip preferably ) Sharp razor blade Ruler a strip of strong fiber tape Thin nose Pliers
More informationTechnical Data Sheet PART A & PART B
Technical Data Sheet PART A & PART B NuPool Epoxy 2 Pack System PART A Product Description NuPool Epoxy Features: NuPool Epoxy is an isocyanate free, high build gloss epoxy coating that is impervious to
More informationDornier Do R 4 Super-Wal
Dornier Do R 4 Super-Wal Model Aviation Laddie Mikulasko s Dornier Do R 4 Super-Wal Build the multiengine, record-setting seaplane. Article, plans, instructions, and photos by Laddie Mikulasko. Complete
More informationMarking films application guide
Marking films application guide The application techniques that we will describe should help users by making their job easier, or by saving them time. However, we know that all the advice in the world
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS SpectroFlex Surfacer 5400. Permasolid HS SpectroFlex Surfacer 5400 is an innovative coloured 2K HS surfacer system based on new generation acrylic resins. The system
More informationSeamless Acoustical Plaster Solutions
Seamless Acoustical Plaster Solutions A seamless acoustical plaster solution The Fade system is a high quality plastering solution that absorbs unwanted noise in a wide range of environments. As an acoustic
More informationManual 1: working with cutting films. MANUAL 1. Working with cutting films. March 2017
Manual 1: working with cutting films. MANUAL 1 R Working with cutting films March 2017 Manual 1: working with cutting films. R 1 NECESSARY TOOLS It goes without saying that you need the right tools if
More informationSECTION 48 - TRAFFIC STRIPES AND PAVEMENT MARKINGS TABLE OF CONTENTS
SECTION 48 - TRAFFIC STRIPES AND PAVEMENT MARKINGS TABLE OF CONTENTS Section Page 48-1 GENERAL... 48.1 48-2 THERMOPLASTIC TRAFFIC STRIPES AND PAVEMENT MARKINGS... 48.1 48-3 PAINTED TRAFFIC STRIPES AND
More informationTex-206-F, Compacting Specimens Using the Texas Gyratory Compactor (TGC)
Contents: Section 1 Overview...2 Section 2 Part I, Compacting Specimens Using the TGC...3 Section 3 Part II, Correlating the Texas...9 Section 4 Notes...12 Section 5 Archived Versions...13 Texas Department
More informationBasic Flows in a Microfluidic Device
Basic Flows in a Microfluidic Device Vishal Tandon 1 Introduction Microfluidic devices are used to transport, mix, and separate analytes in small sample volumes for chemical or biological analysis. Understanding
More informationCounty of Sacramento Standard Construction Specifications January 1, 2008 TECHNICAL PROVISIONS
County of Sacramento Standard Construction Specifications January 1, 2008 TECHNICAL PROVISIONS SECTION 48 TRAFFIC STRIPES AND PAVEMENT MARKINGS 48-1 GENERAL Traffic stripes and pavement markings shall
More informationHow to Cut Shafts and Glue T-tops on KIALOA Stand-Up Paddles
How to Cut Shafts and Glue T-tops on KIALOA Stand-Up Paddles Sizing: Determine the size for your paddle by adding 6-10 to your overall height. If you paddle more frequently in the surf, lean towards the
More informationBUILDING INSTRUCTIONS
Z I P P M A N U FA C T U R I N G A Zippkits R/C Boat BUILDING INSTRUCTIONS 2010 Zipp Manufacturing Frankfort, New York 13340 www.zippkits.com Table of Contents Introduction 1 Engine Mounting 30 S E C T
More informationW00 - W999 OCTOBASE ECO PLUS SYSTEM
W00 W999 OCTOBASE ECO PLUS SYSTEM GENERAL INFORMATION W00 W999 Octobase Eco Plus System is a waterbased basecoat layer in a clearoverbase system. Suitable for passenger cars, touring cars and commercial
More informationTugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
More informationSalt Lowers the Freezing Point of Water
Salt Lowers the Freezing Point of Water Topic Sodium chloride (NaCl), salt, lowers the freezing point of water. Introduction Salt is added to ice in ice cream freezers because salt lowers the freezing
More informationScience 8 B Topic 4-6 Flow Rate and Viscosity fluids resistance to flow viscosity viscous higher viscosity it has liquids and gases
Science 8 B Topic 4-6 Flow Rate and Viscosity - A fluids resistance to flow (its thickness or thinness) is called viscosity - A thicker a liquid is, the more viscous it is and the higher viscosity it has
More informationTECHNICAL DATA SHEET INNOPUR COURT AC-200 ( RESURFACER ) WATERBORNE REPAIR AND ADHESION MATERIAL FOR ASPHALT AND CONCRETE
INNOPUR COURT AC-200 ( RESURFACER ) TECHNICAL DATA SHEET WATERBORNE REPAIR AND ADHESION MATERIAL FOR ASPHALT AND CONCRETE DEFINITION Acrylic emulsion based, waterborne, flexible and providing good adhesion
More informationTechnical Service BULLETIN
Technical Service BULLETIN May 5, 2000 00 ECHO BO018 00 BODY Introduction Blackout tape is used instead of black paint on the door sash of the 2000 ECHO. Please use the following instructions to apply
More informationLittle Dog Dual Deploy
Little Dog Dual Deploy John Wilke & Paul Fechtmeister September 2010 All dimensions are in inches unless specified Construction Notes: Other items you will need: One set of epoxy Motor One sheet of 120
More informationAQUABASE PLUS P Performance Clearcoat
Designed for use with PDS N5.9.6C June 2018 AQUABASE PLUS P190-6930 Performance Clearcoat PRODUCT DESCRIPTION AQUABASE Plus P190-6930 Performance Clearcoat is designed specifically for use with Aquabase
More informationHip Block Installation Instructions:
Hip Block Installation Instructions: The instructions that follow are shown for our low profile hip blocks installed in a Storm Chaser M C-1. However, the very same technique can be used for any of our
More informationDECAL APPLICATION INSTRUCTIONS
DECAL APPLICATION INSTRUCTIONS 1. Measure where you want your decal to be. Then tape in place on 1 side only to use as a hinge, using regular masking tape. Place your tape on the top, bottom or either
More informationInstallation of Nylon Putting NP50
Installation of Nylon Putting NP50 1. Layout of Green and Existing Ground Preparation Step 1: Determine the size and shape of your green as well as any chipping stations and/or sand traps. Step 2: Measure
More informationDuraPad On-Deck Circles
DuraPad On-Deck Circles Page 1 CALL FOR YOUR QUOTE TODAY! On-Deck Circles Page 2 Dura-Pad On-Deck Circles with Logos Page 3 EFFECTIVE: JANUARY 1, 2017 DURA PAD ON-DECK CIRCLES, FUNGO CIRCLES & COACHES
More informationUNIVERSITY OF ROCHESTER MEDICAL CENTER
1. Purpose/Scope: This procedure defines the operation, maintenance and calibration of the Beckman 2. General Policy: The HIC will adhere to the specific guidelines recommended by Beckman Coulter s instruction
More informationEuropean Handball Federation TM EHF Beach Handball Commission
Beach Handball Court Construction Guide EHF Promotion and Development Vienna, March 2016 1 Guide topics Location Court, markings Goals, lines Construction Sand quality requirements Lighting requirements
More informationHealthandSafetyOntario.ca. Hazard: Compressed Gases. Hazard: Compressed Air. Hazard: Noise
Preparing a Boat for Body Work or Repainting Preparing boats for body work or repainting involves many hazards to the eyes, skin, hearing, lungs, etc. Working with fiberglass has many potential inhalable
More informationD8150 EU-139. Performance Clearcoat. Preparation of Substrate:
Product Description: GLOBAL REFINISH SYSTEM Performance Clearcoat is a premium quality high solids clear specifically formulated for today s high production shops. The exceptionally short bake cycle and
More informationSECTION 48 - TRAFFIC STRIPES AND PAVEMENT MARKINGS TABLE OF CONTENTS
SECTION 48 - TRAFFIC STRIPES AND PAVEMENT MARKINGS TABLE OF CONTENTS Section Page 48-1 GENERAL...48.1 48-2 THERMOPLASTIC TRAFFIC STRIPES AND PAVEMENT MARKINGS...48.1 48-3 PAINTED TRAFFIC STRIPES AND PAVEMENT
More informationSECTION SHOWER AND BATH ENCLOSURES. Display hidden notes to specifier by using Tools / Options / View / Hidden Text.
SECTION 10185 SHOWER AND BATH ENCLOSURES Display hidden notes to specifier by using Tools / Options / View / Hidden Text. PART 1 GENERAL 1.1 SECTION INCLUDES A. Bathtub wall enclosures. B. Shower wall
More informationCOATINGS SPRAY GUIDE Acrylics (210, 211, 211HT, and 212)
This guide covers handling and airless spray application of American WeatherStar waterborne single component acrylic elastomeric coatings. These American WeatherStar products require only complete evaporation
More informationPART II Building the MDV-1
21 PART II Building the MDV-1 The MDV-1 is a simple, easily driven, seaworthy boat intended for both rowing and power propulsion. Its general-purpose design is suitable for inshore waters around the world.
More informationUMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING
UMBILICAL CORD MODEL FOR UMBILICAL VEIN CATHETERIZATION TRAINING A Guide to its Construction and Usage INTRODUCTION Introduction This training model aims to familiarize clinicians with umbilical vein catheterization
More information1/4 SHEET PALM SANDER
1/4 SHEET PALM SANDER OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationPLASTIC BEACH PROTOCOLS
PLASTIC BEACH PROTOCOLS Plastic Beach aims to collect microplastic pollution data on sandy beaches around the world. The program empowers volunteers to collect important data that will be used to monitor
More informationBike-Shell Model 301P
Bike-Shell Model 301P NEW design, one piece FRP Composite bike locker NO ASSEMBLY required Specify the 300 Series lockers for the highest customer satisfaction from the no-assembly ready-touse delivery
More information