PARTS IDENTIFIER HARDWARE

Transcription

1

2 3Connect two 3 pin sensor connector from main circuit line to sensor connectors from ball collector. The connection position is under hockey table. PARTS IDENTIFIER HARDWARE DESCRIPTION QTY Plug 6V DC adaptor to AC plug(white), and connect the output plug from 6V DC adaptor to female plug from switch box. P MAIN ASSEMBLE P2 LONG LEG PANEL 5. Game instruction: (). Turn on the power, there will be as tart up music. After the start up music, the "thirty minutes" voice will be played, and the 30 LED will be flashing, the scorer is now at stand-by mode. (2). You can press "SELECT" key to select game modes: 30 minutes, 20 minutes, 0 minutes, points. The corresponding LED will be on, and the game time will be shown on central display. (3). After the game mode has been selected, you can press "RESET" key to start playing. At this time, the corresponding LED will stop flashing, and both side of home, visitor's score will cleared to zero. The game will be started after the start music has been played, and the game time will start to count down. (). All display will be shutdown after 5 minutes of stand-by if no game has been started, you can wake up the scorer by pressing "RESET" key or "SELECT" key. (5). After the game has been started, if home or visitor has gained points, their score will be increment one by one, the cheering voice will be played. After the voice has been played, the next point can be counted. (6). There will be a "two minutes" warning when game time has only 2 minutes left. (7). After the game time is up, the scorer will play "home win" or " visitor win" depends on which team has more scores. After that, the scorer will enter sand-by mode. (8). If both teams have the same score when the time is up, the game will be extended by 2 minutes. (9). If both teams still get the same score after 2 minutes extended period, it will be a "tie game" and the game is over. (0). You can press "RESET" key to abort the current game. 6. Attention: (). Please unplug power adaptor from outlet if you would not play it for a long time. (2). Please do not splash water or other fluid over soccer unit to prevent damages. (3). The sensor units must be plugged and aim at each other before the scorer power is turned on. (). To reset the score counter, you can simply turn off the power then turn on again. The normal function of the product may be disturbed by Strong Electro Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location. P3 P3A P PA P5 P6 P7 P8 LEG LEG LEG PANEL LEG PANEL LOWER SIDE APRON LOWER END APRON CORNER BALL COLLECTOR

3 PARTS IDENTIFIER DELUXE ELECTRONIC SCORER II operation manual HARDWARE DESCRIPTION P9 P0 QTY SUPPORT BRACKET LEG LEVELER 8 H /"X-/" BOLT 2 H2 3/8"x2-/2" BOLT 6 H3 /"x3" BOLT H 3/6"x-5/8" Bolt H5 3/6" Lock Nut H6 #7X" ROUND HEAD SCREW H7 #7X/2" ROUND HEAD SCREW 2 H8 #7X3/" ROUND HEAD SCREW 0 H9 /" FLAT WASHER 28 H0 3/8" FLAT WASHER 6 H Bolt / Lock Nut 2 2. Description: Counts the points by IR sensors pairs attached to the table goals. Display game modes and game time,scores by LEDs and seven segment displays. 2. Safety Precaution: (). Do not open the cover of score unit to prevent injure by electricity. (2). Operating environment: indoor use 3. Specification: (). Display : LED. (2). Sensor : Infrared transmitter/receiver pair. (3). Power Supply : DC 6V adaptor. (). Power consumption : max0ma,min280ma(about max2.6w). (5). Accessories: operation manual, 6V DC adaptor, sensor unit x 2. Installation instruction:,fixing tube 2,Score counter,switch box 5,Balll collector 3,Hockey Table 6,Main circuit line ()Place main circuit line into fixing tube to switch box which includes one 5 pin connector and two 3 pin sensor connectors. (2)Connect 5 pin connector of main circuit line to 5 pin connector from switch box. This connection will be placed in switch box.

4 9.Shown FIGURE 9. PARTS IDENTIFIER HARDWARE DESCRIPTION QTY A HOCKEY PUCK A2 HOCKEY STRIKER Motor power A3 TOOL A GLUE A5 PUCK CATCHER A6 TRANSFORMER A7 Out let box Transformer A8 A8 A9 Figure 9 A9

5 .Find a clean,level place to begin the assembly of your hockey table.we recommend building the table on the box top to protect the parts during assembly. Place the main cabinet P on the ground with the playing surface facing down. Figure 2. Attach the leg bracket (P PA,P3A) using bolts H and washer H9 as shown infigure 2. Repeat this step for all four legs. H9 Washer H Bolt P Leg Panel H7 P8 P3A Leg P3 Leg PA Leg Panel Figure 2 Figure 8

6 For the following step, use the glue provided (A) to help secure the parts together. Use the glue behind the wood blocks on the lower aprons and on the edges of the support brackets. Wipe off any excess glue during this process with a damp cloth. 3. Attach the lower sdie panels P5 and the lower dne panels P6 using screws H8 as shown in FIGURE 3. Make sure the edges of the upper and lower aprons are flush with each other as shown below. Next attach the support brackets P9 between the lower panels and the frame screws H ausing s shown in FIGURE 3. Lock Nut P9 Support Bracket H8 Bolt H8 P5 Lower Side Panel P6 Lower End Panel Bolt / Lock Nut Figure 7 Figure 3

7 .Attach the corner posts P7 using screws H7 as shown in FIGURE. Next center the puck catchers A5 over the opening in the end panel and attach using screws H7 as shown in FIGURE. 6. Attach the previously made leg panel assemblies to the main cabinet using bolts H3 and washers H9 as shown in FIGURE 6. H7 P7 Corner Post A5 Puck Catcher H7 Washer Bolt H9 H3 Figure P2 Long Leg Panel 5. Attach the previously made leg assemblies to the main cabinet using bolts H2 and washers H0 as shown in FIGURE 5. Next screw one leg leveler P0 into the bottom of each leg. P0 Leg Leveler H0 Washer H2 Bolt Figure 5 Figure 6