Internal Arc Simulation in MV/LV Substations. Charles BESNARD 8 11 June 2009
|
|
- Mitchell Bates
- 5 years ago
- Views:
Transcription
1 Internal Arc Simulation in MV/LV Substations Charles BESNARD 8 11 June 2009
2 The Internal Arc Fault The fault A highly energetic and destructive arc (10, 20, 40 MJ!) The effects and the human risks Overpressures can cause parts ejection or wall rupture Hot gases flows can burn on their way On The equipment > std > Type test for a given equipment > Simulation The surrounding (Substation / Electrical room) > ( std) > not a test for each customized surrounding! > Simulation can help! 2
3 The internal arc simulation tool A frame: Fluid Dynamics software A Physical description method of internal arc fault: Equivalent energy injection Equivalent mass injection (plastic vaporization) Radiation, air properties at high temperatures, To get pressure and gas channeling in every self-designed geometry including: Equipment But also customized surrounding 3
4 Simulation in the equipment Inputs Simplified geometry A ring main unit Electrical parameters 16 ka, 3-phases fault Fault location Switch compartment Switch compartment Cable compartment Arc location Buffer Volume Computation I (A) Short-circuit currents ,02 0,04 0,06 0,08 0,1 Time (s) I1 I2 I3 Power (W) 2,5E+07 2,0E+07 1,5E+07 1,0E+07 5,0E+06 0,0E+00 Instant Power 0 0,05 0,1 0,15 0,2 Time (s) 4
5 Simulation in the equipment Pressure cartography and gas channeling Shock wave (2ms) Pressure rise and decompression (50ms) Outputs Pressure curves are validated through a type-test 5
6 Simulation in a variable surrounding Vent area Average configuration Room volume 300x x x ka 20 m 3 50 m 3 15 m 3 Decompression Interface 200x x x300 6
7 Simulation in a variable surrounding The point of interest is the average pressure in the substation Note that some wall regions are overstressed, what has to be analyzed with pressure maps video 7
8 Conclusion People become more and more concerned about knowing overpressures in their substations or electrical rooms, consecutively to an arc fault Surroundings of electrical equipments are widely diversified It is a question of people safety and building protection Numerical simulation has a strong role to play in this field, because a type test can not be performed on each unique customer s facility The simulations take advantage of a generic tool describing the fault, inside and outside the equipment A customized design can be simulated to match the reality as close as possible It is a prospective for the evolution of /202 standards to take into account the overpressure in the surroundings 8
9 9
10 Appendices Max pressure? Average pressure? What has to be considered Usually, the average pressure in the room, exerted on the entire wall gives the highest equivalent load The max pressure is obtained locally (in front of exhaust) and does not extert on the entire wall It can be taken into account with pressure maps 10
11 Appendices The parameters of the room can hardly have an influence on the pressure inside the device However, the parameters at the interface switchgear / room are very important The exhaust area (varying 170%) between buffer volume and room can change the pressure inside the buffer volume (varying 70%) 11
12 Appendices The internal arc fault implies thermal exchanges as pressure rises The ones depend on the others That is why a CFD description is appropriated, to integrate all the effects 12
13 Appendices Other examples A modular switchgear, with upper exhaust 13
MODELING&SIMULATION EXTRAPOLATED INTERNAL ARC TEST RESULTS: A COUPLED FLUID-STRUCTURAL TRANSIENT METHODOLOGY
MODELING&SIMULATION EXTRAPOLATED INTERNAL ARC TEST RESULTS: A COUPLED FLUID-STRUCTURAL TRANSIENT METHODOLOGY Jérôme DOUCHIN Schneider Electric France Jerome.douchin@schneider-electric.com Ezequiel Salas
More informationAnalysis of Pressure Rise During Internal Arc Faults in Switchgear
Analysis of Pressure Rise During Internal Arc Faults in Switchgear ASANUMA, Gaku ONCHI, Toshiyuki TOYAMA, Kentaro ABSTRACT Switchgear include devices that play an important role in operations such as electric
More informationCFD SIMULATIONS OF GAS DISPERSION IN VENTILATED ROOMS
CFD SIMULATIONS OF GAS DISPERSION IN VENTILATED ROOMS T. Gélain, C. Prévost Institut de Radioprotection et de Sûreté Nucléaire (IRSN), Saclay, France Abstract In order to better understand the risks due
More informationMITIGATE GAS COMBUSTION IN CASE OF INTERNAL ARC
MITIGATE GAS COMBUSTION IN CASE OF INTERNAL ARC Jérôme DOUCHIN Yann CRESSAULT Raphael Danjoux Schneider Electric France Toulouse University France FLIR France Jerome.douchin@ cressault@laplace.univ-tlse.fr
More informationA Computational Assessment of Gas Jets in a Bubbly Co-Flow 1
A Computational Assessment of Gas Jets in a Bubbly Co-Flow 1 Melissa Fronzeo*, 1 Michael Kinzel 1 The Pennsylvania State University, University Park, PA, USA Abstract In this effort, Computational Fluid
More informationThe API states the following about tube rupture for a shell-and-tube heat exchangers:
Tutorial This tutorial describes the theory and modeling process of a tube rupture event using the special element type Rupture element in BOSfluids. It covers the algorithm BOSfluids uses to model the
More informationSTAR European Conference 2011
STAR European Conference 2011 Oggetto: Data: Aircraft passenger cabin thermal comfort analysis by means of integrated mono dimensionałcfd approach 22-23 March 2011 Ver.: P. Borrelli, On Board General Systems,
More informationNew Findings for the Application of Systems for Explosion- Isolation with Explosion Venting
529 A publication of CHEMICAL ENGINEERING TRANSACTIONS VOL. 48, 2016 Guest Editors: Eddy de Rademaeker, Peter Schmelzer Copyright 2016, AIDIC Servizi S.r.l., ISBN 978-88-95608-39-6; ISSN 2283-9216 The
More informationCable in Conduit Conductor (CICC) quench modelling
DEMO SAMPLE Cable in Conduit Conductor (CICC) quench modelling This demo gives an example of quench simulation for a Central Solenoid (CS). CS is divided into geometrically identical sections (see Fig.
More informationApplication Note AN-107
SPEC Sensor TM Characterization & Calibration Considerations Scope This document is provided to describe the considerations needed to characterize, calibrate, verify and validate the measurement performance
More informationGas density monitor With integrated transmitter Model GDM-100-TI
SF 6 gas solutions Gas density monitor With integrated transmitter Model GDM-100-TI grid Products WIKA data sheet SP 60.05 for further approvals see page 5 Applications Gas density monitoring of closed
More informationTP Description to be used for Customer Technical Specifications
TP Description to be used for Customer Technical Specifications Transformer, On Load Tap Changer, Oil Cable Boxes Explosion and Fire Prevention, from 0.1 MVA TP Description to be used for Customer Technical
More informationInjector Dynamics Assumptions and their Impact on Predicting Cavitation and Performance
Injector Dynamics Assumptions and their Impact on Predicting Cavitation and Performance Frank Husmeier, Cummins Fuel Systems Presented by Laz Foley, ANSYS Outline Overview Computational Domain and Boundary
More informationSingle Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers
More informationBoyle s law Verifying the relation between air pressure and volume measuring air pressure in a closed container.
Objective The purpose of this activity is to analyze the relationship between the pressure and volume of a confined gas at constant temperature, create a hypothesis and proceed to test it using the Labdisc
More informationTP Description to be used for Customer Technical Specifications
TP Description to be used for Customer Technical Specifications Transformer, On Load Tap Changer, Oil Cable Boxes Explosion and Fire Prevention, from 0.1 MVA TP Description to be used for Customer Technical
More informationAnalysis and Comparison of Calculation Methods for Physical Explosions of Compressed Gases
133 A publication of VOL. 32, 13 CHEMICAL ENGINEERING TRANSACTIONS Chief Editors: Sauro Pierucci, Jiří J. Klemeš Copyright 13, AIDIC Servizi S.r.l., ISBN 978-88-9568-23-5; ISSN 1974-9791 The Italian Association
More informationSIMULATION OF ENVIRONMENTAL FLIGHT CONDITIONS
SIMULATION OF ENVIRONMENTAL FLIGHT CONDITIONS BY ADVANCED ALTITUDE SIMULATION Klaus SCHÄFER Institute of Space Propulsion, German Aerospace Centre (DLR) Lampoldshausen, 74239 Hardthausen, Germany klaus.schaefer@dlr.de
More information70e Training - Electrical Safety in the Workplace
70e Training - Electrical Safety in the Workplace Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq This NFPA
More informationCheck Valve Diagnosis by Sectorial Scanning Phased Array Ultrasonic Technique
19 th World Conference on Non-Destructive Testing 2016 Check Valve Diagnosis by Sectorial Scanning Phased Array Ultrasonic Technique Héctor Mariano CALAS DEL CASTILLO 1, Bautista DE LA FUENTE 1, Victor
More informationCROSS CONTAMINATION OF IN-SUITE MURB VENTILATION SYSTEMS
CROSS CONTAMINATION OF IN-SUITE MURB VENTILATION SYSTEMS Presented By: Sandra Dedesko University of Toronto Contributing Authors: Caleb Parker Kim Pressnail Marianne Touchie Dave DeRose Multi-Unit Residential
More informationGas Vapor Injection on Refrigerant Cycle Using Piston Technology
Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2012 Gas Vapor Injection on Refrigerant Cycle Using Piston Technology Sophie
More informationComputer Simulation Helps Improve Vertical Column Induced Gas Flotation (IGF) System
JOURNAL ARTICLES BY FLUENT SOFTWARE USERS JA187 Computer Simulation Helps Improve Vertical Column Induced Gas Flotation (IGF) System Computer simulation has helped NATCO engineers make dramatic improvements
More informationA Depletion Compensated Wet Bath Simulator For Calibrating Evidential Breath Alcohol Analyzers
A Depletion Compensated Wet Bath Simulator For Calibrating Evidential Breath Alcohol Analyzers Slemeyer, A. University of Applied Sciences of Giessen, Dept. of Electrical Engineering 1 Wiesenstr. 14, D-35390
More informationRecent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs.
Recent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs. The hazard level must be quantified and workers properly protected before entering
More informationMODELLING OF FUME EXTRACTORS C. R.
LD8 19th International Symposium of Ballistics, 7 11 May 21, Interlaken, Switzerland MODELLING OF FUME EXTRACTORS C. R. Woodley WS4 Guns and Warheads Department, Defence Evaluation and Research Agency,
More informationElectromechanical pressure switches
Presentation Electromechanical pressure switches OsiSense XM For power circuits, type XMP Presentation Pressure switches type XMP are switches for power circuits (direct switching), with an adjustable
More informationZIN Technologies PHi Engineering Support. PHi-RPT CFD Analysis of Large Bubble Mixing. June 26, 2006
ZIN Technologies PHi Engineering Support PHi-RPT-0002 CFD Analysis of Large Bubble Mixing Proprietary ZIN Technologies, Inc. For nearly five decades, ZIN Technologies has provided integrated products and
More informationGas Network Craftsperson
Gas Network Craftsperson Unit EIAU016 Carrying out Fault Diagnosis on Electrical Equipment and Circuits This assessment specification has been developed as part of the network maintenance craftsperson
More informationProgrammable Submersible Level Transmitters
Programmable Submersible Level Transmitters PTM/N/RS485 CUSTOMER BENEFITS High flexibility due to scalalbe pressure range Digital (RS485) and analogue (4-20mA) output signal in one sensor Available as
More informationNumerical simulation of the ALBA s synchrotron cooling system response to pump start-up and shut-down Page 1
Numerical simulation of the ALBA s synchrotron cooling system response to pump start-up and shut-down Page 1 Abstract This project consists of the development and validation of a numerical model to simulate
More informationEdit this text for your title
Edit this text for your title MEK 4450 Marine Operations Edit this text for your sub-title Presenter name, location, date etc. Kværner ASA / DNV, Fall 2013 Lesson 2/3 Lift phases Load out Transportation
More informationNumerical study of water plume behavior under shallow depth explosion
Structures Under Shock and Impact IX 13 Numerical study of water plume behavior under shallow depth explosion C.-C. Liang, T.-H. Liu & W.-M. Tseng Department of Mechanical and Automation Engineering, Da-Yeh
More informationThis presentation provides an overview of modern methods for minimizing the arc-flash hazard.
Electricity is all around us. An uncontrolled release of electric energy is extremely dangerous, posing a threat to human life, causing equipment damage, and jeopardizing the manufacturing process that
More informationInfluencing Factors Study of the Variable Speed Scroll Compressor with EVI Technology
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Influencing Factors Study of the Variable Speed Scroll Compressor with EVI Technology
More informationAutodesk Moldflow Communicator Process settings
Autodesk Moldflow Communicator 212 Process settings Revision 1, 3 March 211. Contents Chapter 1 Process settings....................................... 1 Profiles.................................................
More informationMCQ Gas Blender 100 Series 3 Channels Gas Mixer
Channels Gas Mixer Revision 1.8 October 2016 High Performance Digital Gas flow Gas Dilutor Blender & Gas for Mixing flow Mixing Gases System and Calibration Routines Technical Data Sheet Lab in a box From
More information86BSD Backside Digital Output
Stainless steel with O-ring seal Pressure/temperature read-out Backside digital output ASIC calibrated Absolute, gage Cable/connector option Low power option DESCRIPTION The 86BSD is a small profile, media
More informationTutorial. BOSfluids. Relief valve
Tutorial Relief valve The Relief valve tutorial describes the theory and modeling process of a pressure relief valve or safety valve. It covers the algorithm BOSfluids uses to model the valve and a worked
More informationParametrable / Programmable Pressure Transmitter
Parametrable / Programmable Pressure Transmitter PTM/RS485 CUSTOMER BENEFITS High flexibility due to scalalbe pressure range Digital (RS485) and analogue (4-20mA) output signal in one sensor Available
More informationHYPOXIC AIR FIRE PREVENTION SYSTEM TECHNICAL SPECIFICATION
HYPOXIC AIR FIRE PREVENTION SYSTEM TECHNICAL SPECIFICATION Introduction: Hypoxic Air Fire Prevention System is a revolutionary fire prevention technology. It has the unique ability to create a breathable
More informationTechnical Data Sheet MF010-O-LC
Technical Data Sheet MF010-O-LC - 1 - 1. Properties The oxygen measuring system MF010-O-LC determines the oxygen content in gas mixtures up to a temperature of 250 C. It is particularly suitable for the
More informationIEC April Authorized Sole Agent : PT. Wisma Niagatama Perkasa. Phone : (031) Fax. : (031)
IEC 62271-200 April 2004 Authorized Sole Agent : PT. Wisma Niagatama Perkasa Phone : (031) 5041242 Fax. : (031) 5044580 IEC 62271-200 Introduction Scope This standard specifies requirements for factory-assembled
More informationAC : A LABORATORY EXERCISE TO DEMONSTRATE HOW TO EXPERIMENTALLY DETERMINE THE OPERATING POINT FOR A FAN
AC 2007-206: A LABORATORY EXERCISE TO DEMONSTRATE HOW TO EXPERIMENTALLY DETERMINE THE OPERATING POINT FOR A FAN Robert Edwards, Pennsylvania State University-Erie Robert Edwards is currently a Lecturer
More informationANALYSIS OF HEAT TRANSFER THROUGH EXTERNAL FINS USING CFD TOOL
ANALYSIS OF HEAT TRANSFER THROUGH EXTERNAL FINS USING CFD TOOL B. Usha Rani 1 and M.E Thermal 2 1,2 Asst.Professor, Dadi Institute of Engineering and Technology, India Abstract-The rate of heat transfer
More informationNEAR FIELD EFFECTS OF SMALL SCALE WATER BLEVE
Safety and Security Engineering VII 465 NEAR FIELD EFFECTS OF SMALL SCALE WATER BLEVE ROLAND EYSSETTE 2, FREDERIC HEYMES 1, JAMES CRAWFORD 2 & ALBRECHT M. BIRK 2 1 Ecole des Mines d Alès, LGEI/ISR, France
More informationTHE TUNNELS IN GUADARRAMA FOR THE HIGH SPEED RAILWAY
THE TUNNELS IN GUADARRAMA FOR THE HIGH SPEED RAILWAY MAP GUADARRAMA TUNNELS THE TUNNELS IN GUADARRAMA FOR THE HIGH SPEED RAILWAY The tunnels in Guadarrama for the high speed train (AVE) entered into service
More informationCharacterizing Flow Losses Occurring in Air Vents and Ejector Pins in High Pressure Die Castings
This paper is subject to revision. Statements and opinions advanced in this paper or during presentation are the author s and are his/her responsibility, not the Association s. The paper has been edited
More informationINSTALLATION,OPERATION AND MAINTENANCE INSTRUCTIONS DRY AIR COOLER
INSTALLATION,OPERATION AND MAINTENANCE INSTRUCTIONS DRY AIR COOLER Installation Operation and Maintenance Location The unit should not be located on roofs finished with asphalt. When this is unavoidable
More informationBubble Coalescence and Breakup in Gas-Liquid Stirred Tank Reactors
Bubble Coalescence and Breakup in Gas-Liquid Stirred Tank Reactors Rahman Sudiyo Background Stirred tank reactors are widely used in chemical, pharmaceutical and biochemical industries. Mass transfer between
More informationUser Manual MFCS TM -EZ
User Manual MFCS TM -EZ Version 6A_December 2016 1. INTRODUCTION 5 2. GENERAL INFORMATION 6 2.1 General functioning 6 2.2 Different MFCS TM 6 3. PACKAGE CONTENT 8 4. MFCS TM -EZ DESCRIPTION 9 5. CONNECTIONS
More informationASDX Series Silicon Pressure Sensors
ASDX Series Silicon Pressure Sensors DESCRIPTION The ASDX Series is a Silicon Pressure Sensor offering a ratiometric analog interface for reading pressure over the specified full scale pressure span and
More informationMass Flowmeters. Mass Flowmeters for Gases
Mass Flowmeters Mass Flowmeters for Gases Fast, Accurate, Low Pressure Drop for critical measurement applications! Flow (Std l/min) Response to a step change in flowrate 300 200 100 4 Milliseconds 63%
More informationBoyle s Law: Pressure-Volume Relationship in Gases
Boyle s Law: Pressure-Volume Relationship in Gases Experiment The primary objective of this experiment is to determine the relationship between the pressure and volume of a confined gas. The gas we use
More informationDEVELOPMENT OF P4.1 ALTITUDE SIMULATION FOR VINCI ENGINE
DEVELOPMENT OF P4.1 ALTITUDE SIMULATION FOR VINCI ENGINE K. Schäfer, C. Böhm, H. Kronmüller, H. Zimmermann, German Aerospace Centre (DLR), Institute of Space Propulsion, Lampoldshausen, 74172 Hardthausen,
More informationTR Electronic Pressure Regulator. User s Manual
TR Electronic Pressure Regulator Page 2 of 13 Table of Contents Warnings, Cautions & Notices... 3 Factory Default Setting... 4 Quick Start Procedure... 5 Configuration Tab... 8 Setup Tab... 9 Internal
More informationReferences, characteristics. References (1) Complementary characteristics not shown under general characteristics (page 30395/3)
References, characteristics Electromechanical pressure switches For power circuits, type XMP. IP degree of protection Size (87 psi). Adjustable differential, for regulation between thresholds Switches
More informationOptimization of Ejector's Performance With a CFD Analysis. Amanda Mattos Karolline Ropelato Ricardo Medronho
Optimization of Ejector's Performance With a CFD Analysis Amanda Mattos Karolline Ropelato Ricardo Medronho 2 Introduction Ejectors Equipment industrially used and based on the Venturi phenomena; With
More informationAPPLICATION OF CAVITATION MODELS TO STUDY A REAL CASE OF DIE EROSION
presents: APPLICATION OF CAVITATION MODELS TO STUDY A REAL CASE OF DIE EROSION Daniele Grassivaro Process Engineer at Form S.r.l. June 2016 16th FLOW-3D European Users Conference 1 Cavitation in HPDC June
More informationMETRO System Design. Witt&Sohn AG Aug-11
METRO System Design Content Purpose Comparison Metro Road tunnel Ventilation Types/ Systems Operation Modes Pre-/ Detailed Design Summary Purpose Presentation: Degree of Complexity of Metro Systems No
More informationTECHNICAL PAPER PRESENTATION
1 W E L C O M E T O A C O M E T 2 0 1 7 TECHNICAL PAPER PRESENTATION 2 INSULATION AND SWITCHING IN ENVIRONMENTALLY FRIENDLY GASES BY JAVIER MANTILLA 3 A B O U T T H E A U T H O R BRIEF BIO JAVIER MANTILLA
More informationImprove Process Reliability
Convenient Conductivity Calibration to Meet Pharmacopeia Regulations Pharmacopeias require that conductivity measurement systems be periodically calibrated to ensure their precision. The range of accessories
More informationWhy do I need to do an Arc-Flash Analysis?
Why do I need to do an Arc-Flash Analysis? Presented By Tom Norwood for Alexander Nizov, P.E. Principal/Manager Electrical Engineering Division TRAINING INSTITUTE, INC. A SUBSIDIARY OF MEGGER Hazards Analysis
More informationTHEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE
THEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE S.Ramamurthy 1, R.Rajendran 1, R. S. Dileep Kumar 2 1 Scientist, Propulsion Division, National Aerospace Laboratories, Bangalore-560017,ramamurthy_srm@yahoo.com
More informationHYDROGEN RISK ANALYSIS FOR A GENERIC NUCLEAR CONTAINMENT VENTILATION SYSTEM
HYDROGEN RISK ANALYSIS FOR A GENERIC NUCLEAR CONTAINMENT VENTILATION SYSTEM u, Z. 1 and Jordan, T. 2 Karlsruhe Institute of Technology, P.O. Box 3640, 76021 Karlsruhe, Germany 1 zhanjie.xu@kit.edu, 2 thomas.jordan@kit.edu
More informationCONSIDERATION OF DENSITY VARIATIONS IN THE DESIGN OF A VENTILATION SYSTEM FOR ROAD TUNNELS
- 56 - CONSIDERATION OF DENSITY VARIATIONS IN THE DESIGN OF A VENTILATION SYSTEM FOR ROAD TUNNELS Gloth O., Rudolf A. ILF Consulting Engineers Zürich, Switzerland ABSTRACT This article investigates the
More informationFree Surface Flow Simulation with ACUSIM in the Water Industry
Free Surface Flow Simulation with ACUSIM in the Water Industry Tuan Ta Research Scientist, Innovation, Thames Water Kempton Water Treatment Works, Innovation, Feltham Hill Road, Hanworth, TW13 6XH, UK.
More informationResponse of Flare base Self supporting Steel stack. Under the static & dynamic wind loads with variable wind speed
Response of Flare base Self supporting Steel stack Under the static & dynamic wind loads with variable wind speed Rinki [1], Shashi Shekhar Singh [2] MVN University, Palwal, Haryana [1][2] rinkitanguriya27@gmail.com
More informationArc flash versus arc resistant; different concerns
Technical Collection Technical paper N PCIC Middle-East -78 Arc flash versus arc resistant; different concerns Didier FULCHIRON, Schneider Electric France. Abstract "Arc flash" and "arc resistant" terms
More informationThermo Scientific Model 146i Principle of Operation
Thermo Scientific Model 146i Principle of Operation The Model 146i Multi-gas Calibrator dilutes calibration gases to precise concentrations. The diluted gases are used to perform zero, precision and Level
More informationSDX Submersible Depth Transmitter User Manual
SDX Submersible Depth Transmitter User Manual October 2007 USER INFORMATION Stevens makes no warranty as to the information furnished in these instructions and the reader assumes all risk in the use thereof.
More informationQuadruple mass spectrometers (transducer type)
Quadruple mass spectrometers that meet the need for sensitive analysis and low outgassing which were specifically designed to be controlled by PCs Quadruple mass spectrometers (transducer type) M-070QA-TDF,
More information2. Determine how the mass transfer rate is affected by gas flow rate and liquid flow rate.
Goals for Gas Absorption Experiment: 1. Evaluate the performance of packed gas-liquid absorption tower. 2. Determine how the mass transfer rate is affected by gas flow rate and liquid flow rate. 3. Consider
More informationPedestrian traffic flow operations on a platform: observations and comparison with simulation tool SimPed
Pedestrian traffic flow operations on a platform: observations and comparison with simulation tool SimPed W. Daamen & S. P. Hoogendoorn Department Transport & Planning, Delft University of Technology,
More informationTube rupture in a natural gas heater
Tube rupture in a natural gas heater Dynamic simulation supports the use of a pressure safety valve over a rupture disk in the event of a tube rupture HARRY Z HA and PATRICK STANG Fluor Canada Ltd A fast
More informationCFD and Physical Modeling of DSI/ACI Distribution
CFD and Physical Modeling of DSI/ACI Distribution APC Round Table & Exposition July 09, 2013 Matt Gentry mgentry@airflowsciences.com 734-525-0300 1 Outline Introduction Flow Analysis Techniques Application
More informationWIND LOADS / MOORING & FISH TAILING. Arjen Koop, Senior Project Manager Offshore Rogier Eggers, Project Manager Ships
WIND LOADS / MOORING & FISH TAILING Arjen Koop, Senior Project Manager Offshore Rogier Eggers, Project Manager Ships OVERVIEW Wind Loads Wind shielding Fish tailing? 2 WIND LOADS FOR OFFSHORE MARS TLP
More informationExercise 2-2. Second-Order Interacting Processes EXERCISE OBJECTIVE DISCUSSION OUTLINE. The actual setup DISCUSSION
Exercise 2-2 Second-Order Interacting Processes EXERCISE OBJECTIVE Familiarize yourself with second-order interacting processes and experiment with the finer points of controller tuning to gain a deeper
More informationInternational Journal of Advance Engineering and Research Development DESIGN CALCULATIONS TO EVALUATE PERFORMANCE PARAMETERS OF COMPRESSOR VALVE
Scientific Journal of Impact Factor (SJIF): 4.72 International Journal of Advance Engineering and Research Development Volume 4, Issue 7, July -2017 e-issn (O): 2348-4470 p-issn (P): 2348-6406 DESIGN CALCULATIONS
More informationExperimental determination of deflagration explosion characteristics of methane air mixture and their verification by advanced numerical simulation
Structures Under Shock and Impact XII 169 Experimental determination of deflagration explosion characteristics of methane air mixture and their verification by advanced numerical simulation M. Mynarz,
More informationBPZM-MRD Nitrogen Injection System
BPZM-MRD Nitrogen Injection System (Transformer protector) Overview BPZM-MRD Nitrogen Injection Explosion Prevention & Fire Protection System became more advanced fire protection and explosion prevention
More informationIncorporating 3D Suction or Discharge Plenum Geometry into a 1D Compressor Simulation Program to Calculate Compressor Pulsations
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2012 Incorporating 3D Suction or Discharge Plenum Geometry into a 1D Compressor Simulation
More informationAmerican Chemical Society (ACS) 246th ACS National Meeting Indianapolis, Indiana September 9, 2013
American Chemical Society (ACS) 246th ACS National Meeting Indianapolis, Indiana September 9, 2013 J. Kelly Thomas, Ph.D. Baker Engineering and Risk Consultants San Antonio, TX (KThomas@BakerRisk.com)
More informationMass Flow Controller (MFC) for Gases
Mass Flow Controller (MFC) for Gases Bypass MFC with capillary technology for nominal flow rates from 5 ml N /min to 15 l N /min Applicable for aggressive gases Compact design and digital communication
More informationMODERN APPROACH FOR CONDITION MONITORING OF POWER TRANSFORMERS USING DISSOLVED GAS ANALYSIS
MODERN APPROACH FOR CONDITION MONITORING OF POWER TRANSFORMERS USING DISSOLVED GAS ANALYSIS Zohra Khan 1, Avinash Paranjpe 2 1 ME Student, Electrical Power System, PES COE/ Dr. B.A.M. University, (India)
More informationInnovative Techniques for Mitigating Arc Flash Exposure
Innovative Techniques for Mitigating Arc Flash Exposure Presented at MEMSA 2009 Annual Meeting & Technical Symposium 2007 Eaton Corporation. All rights reserved. INTRODUCTION. As more and more industries
More informationProgrammable pressure and temperature transmitters PTM/RS485
Programmable pressure and temperature transmitters PTM/RS485 Version: 03-28-2012 Technical Specifications Pressure measuring range (bar) 0.1... 0.5 > 0.5 2 > 2 25 Overpressure 3 bar 3 x FS ( 3 bar) 3 x
More informationHazard Operability Analysis
Hazard Operability Analysis Politecnico di Milano Dipartimento di Energia HAZOP Qualitative Deductive (search for causes) Inductive (consequence analysis) AIM: Identification of possible process anomalies
More informationT EK-SUB 4800C 19 mm Submersible Level Transmitter
Technology Solutions T EK-SUB 4800C 19 mm Submersible Level Transmitter Instruction Manual Document Number: IM-4800C www.tek-trol.com Table of Contents 1 Safety Instructions... 2 1.1 Intended Use... 2
More informationThe Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul
The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration M. Burak Şamşul ITU AYOC 2014 - Milper Pervane Teknolojileri Company Profile MILPER is established in 2011 as a Research and Development
More informationENHANCED LIVE FIRE MORTAR TRAINING USING THE M769 FULL RANGE PRACTICE CARTRIDGE
ENHANCED LIVE FIRE MORTAR TRAINING USING THE M76 FULL RANGE PRACTICE CARTRIDGE 17 May 2005 Mr. Jason Surmanek ARDEC Project Officer (APO) Armament Research, Development & Engineering Command (ARDEC) Mortars
More informationAPPLICATION OF SOUND PROPAGATION (IN THE PERSIAN GULF AND OMAN SEA)
APPLICATION OF SOUND PROPAGATION (IN THE PERSIAN GULF AND OMAN SEA) Seyed Majid Mosaddad Department of Physics, Shoushtar Branch, Islamic Azad University, Shoushtar, Iran Email: mosaddad5@gmail.com Abstract
More informationHeat Pump Connections and Interior Piping
Job Sheet 3 Heat Pump Connections and Interior Piping OBJECTIVES In this job sheet, you will observe how the presence of air in the ground loop affects the geothermal heat pump performance. You will also
More information1.2 Example 1: A simple hydraulic system
Note: It is possible to use more than one fluid in the Hydraulic library. This is important because you can model combined cooling and lubrication systems of a library. The hydraulic library assumes a
More informationThe Science of Quantitative Risk Assessment for Explosives Safety
The Science of Quantitative Risk Assessment for Explosives Safety By John Tatom (Manager, Explosives Safety Group, A-P-T Research, Inc. Quantitative risk assessment (QRA) tools, as described in the QRA
More informationFor a similar sensor with o-ring mounting, refer to the 85BSD digital output pressure sensor.
Weldable or threaded process fittings Pressure/temperature read-out Digital output ASIC calibrated Absolute, gage Cable/connector option Low power option DESCRIPTION The 85BSD is a small profile, media
More informationConsequences on port facilities of a tanker explosion
Structures Under Shock and Impact IX 279 Consequences on port facilities of a tanker explosion P. L. Metropolo 1 & A. E. P. Brown 2 1 Rhodia, Technology Research Centre, Brazil 2 Polytechnic College, University
More informationUser manual. PCA EXCEL one4all with corridorfunction PCA T5 ECO lp with corridorfunction TE one4all with corridorfunction
User manual PCA EXCEL one4all with corridorfunction PCA T5 ECO lp with corridorfunction TE one4all with corridorfunction Contents 1 Introduction...2 2 Installation...2 3 Commissioning...3 4 corridorfunction
More informationFigure 1. Outer dimensions of the model trucks.
1 Standardisation of test method for salt spreader: Air flow experiments Report 3: Simulations of airflow patterns by Jan S. Strøm, Consultant Aarhus University, Engineering Centre Bygholm, Test and Development
More informationDEEPSEA. SeaLite Lumos POWER & LIGHT. Operator s Manual Ruffin Road San Diego, CA USA.
SeaLite Lumos DEEPSEA POWER & LIGHT T: (858) 576-1261 F: (858) 576-0219 4033 Ruffin Road San Diego, CA 92123-1817 USA www.deepsea.com sales@deepsea.com REV 08/27/18 Optical Specifications Specification
More information