>B< Press Water Technical Brochure

Transcription

1 >B< Press Water Technical Brochure

2 Contents 1: General 1.1: General Quality and certifications Benefits Materials and threads Storage and handling Sealing elements Application parameters and requirements Tube compatibility Electrical continuity Recommended water velocities Product guarantee 1.2: Areas of Application : Product Suitability Drinking water installation Heating and cooling systems Local and district heating Thermal solar systems with low operating temperature 1.4: Corrosion Resistance Corrosion and frost protection System commissioning Chemical types, and their function(s) found in commercial products Recommendations for the prevention of corrosion on copper and copper alloy material Flushing of water installations Testing and commissioning drinking water installations Water softening 1.5: Thermal Expansion Effects of expansion Expansion devices 1.6: Loss Coefficients...8 2: >B< Press 12-54mm 2.1: >B< Press Copper Fittings 12-54mm : Fitting Construction Fitting construction 12-54mm 2.3: Product Suitability Compressed air systems 2.4: >B< Press Tools Press jaws Maintenance Compatible Press tools Use of tools 2.5: Installation Requirements Installation dimensions Space required for the pressing process >B< Press tube compatibility sizing Localised annealing Brazing near >B< Press fittings 2.6. Installation Guide : Product Range : >B< Press L mm - NEW 3.1: >B< Press L Copper Fittings Product features Stainless steel grip ring Seal design 3.2: Installation Requirements Installation dimensions Space required for the pressing process >B< Press tube sizing compatibility Pipework protection Localised annealing Brazing near >B< Press fittings 3.3: >B< Press L Tools Tool chart Critical operating instructions - tool and jaw Maintenance mm 3.4: Installation Guide : Product Range : Guarantee...39

3 1.1: General >B< Press fittings are quick and easy to install and are available in copper and red brass. This flame free range is designed with an innovative 3-point press system, with >B< Press L featuring a stainless steel grip ring for additional peace of mind. Both ranges have a leak before press indicator to ensure a secure, permanent leak free joint that is suitable for multiple applications Quality and certification With 110 years of experience in manufacturing innovative technology, Conex Bänninger operates an accredited Quality Management System to EN ISO >B< Press copper and brass fittings are tested and certified by independent national certification bodies like WRAS (Water Regulations Advisory Scheme) confirming its suitability and reliability for use with potable water applications. >B< Press is also certified by the following bodies: WRAS BSI Kitemark DVGW KIWA PZH PCT TYSK Benefits UK UK Germany Holland Poland Russia Ukraine The following are benefits of the >B< Press fitting: Quick and easy to install, saving on labour costs. Permanent, flame-free connection - no hot works permit required. High corrosion resistance. Compatible with various approved press tools and jaws. Suitable for use with hard, half-hard and soft copper tubes to EN Manufactured using high quality materials and standards. Tested and approved by national and international standard authorities. 3-point press safety feature for added security. (12-54mm only). Suitable for use behind plasterboard walls (corrosion protection may be required). 25 years guarantee on fitting. Leak before press indicator. ITB ACS CSTB AENOR SVGW Watermark IAPMO No requirements for soldering materials. Poland France France Spain Switzerland Australia USA Comprehensive range of fittings - sizes from mm. Stainless steel grip ring for additional strength (64-108mm) Materials and threads >B< Press copper fittings are made of oxygen-free copper CU-DHP (material number EN CW024A) which can be combined with copper tubes in accordance with EN >B< Press threaded fittings are manufactured from high quality red brass (EN1982 CC499K) having low lead and nickel and high resistance to dezincification and stress corrosion cracking. All >B< Press threaded fittings are designed and manufactured in accordance with EN (ISO 7-1) and are accordingly thread sealed (threaded connection of conical male threads R /cylindrical female threads Rp). All >B< Press threaded fittings comply with ISO 7 standards Storage and handling For the storage and transportation of >B< Press copper and red brass fittings, it is advisable to leave the fittings in the packaging to conserve the lubrication of the O-rings prior to installations. The O-ring complies with European and international requirements for drinking water such as WRAS approval. Please store in a cool and dry place to protect the fittings from contamination, damage and dirt. Keep out of direct sunlight Black EPDM sealing elements >B< Press copper EPDM O-ring (ethylene propylene diene monomer) contains a synthetically produced, rubber peroxide cured. It is age, ozone and chemical resistant with high elasticity, and excellent cold and heat performance. Please refer to section 1.2 for the acceptable fitting operating parameters for the different applications Application parameters and requirements When using >B< Press, the application parameters in section 1.2 must be observed. The use of different material in a drinking water system must comply with the appropriate codes of practice. In the design and creation of pipework systems the standard engineering practices for drinking water installations must be adhered to. 1 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

4 1.1.7 Tube compatibility >B< Press fittings can be used on hard, half-hard soft copper tubes to EN Compatible dimensions are shown in this brochure, clause 5.2 for 12 to 54mm and clause 2.2 for L sizes Recommended water velocities Please note the maximum allowances for water velocities are per the relevant national standards and codes, which includes BS EN 806 part 2 and part Electrical continuity >B< Press copper and red brass fittings maintain earth continuity without the need for additional continuity straps. 1.2: Areas of Application >B< Press copper and red brass fittings are suitable for use in the following applications. Application Hot and cold water installations Drinking water installations EN 806 and EN 1988 Flow medium General installations for hot and cold potable and nonpotable water outside EN specified requirements Drinking water in accordance with the drinking water ordinance Pressure bar Temp C 16 Range 0 to max max Hot water heaters EN Heating water max Local and district heating tubes EN 4747 Thermal solar systems* with permanent operating temperatures 110 C EN / Cooling systems Heating and district heating water Water and water-glycol mixtures mixing ratio max. 50/50 % Water and water-glycol mixtures mixing ratio max. 50/50 % max 6 Range -35 to min Rainwater harvesting systems Rainwater from cisterns Steam Low pressure steam equipment 1 5 max Fire mains Firefighting water Compressed air (oil-free) Compressed air classes 1-3 as per ISO Industrial and processing water Vacuum piping for non-medical purpose Prepared, softened, partially and partially de-ionized water with a ph of 6.5 Ph ** max max N/A -0.8 Ambient Pipeline in shipbuilding 54mm Water with 6.5 Ph max Field test pressure Water with 6.5 Ph Ambient Protection from corrosive agents must be obtained through insulation. In the absence of protection, a prolonged exposure to corrosive agents, particularly in a chased installation, may cause corrosion. When installing >B< Press copper in chased applications please ensure it is suitably ducted, or shielded with an approved impervious tape (to avoid abrasion). * In thermal solar plants and district heating pipelines with permanently high operating temperatures, our >B< Press Solar press fittings (with the high temperature-resistant FKM sealing element) can be used. =-* In the event of deviating parameters, please contact the technical department. Refer to table 5.3 of this brochure for details of compatible tubes. Not suitable for: Aromatic, aliphatic and chlorinated hydrocarbons, turpentine, benzene, mineral oils. For applications outside those stated in the table above, please contact the technical department: technical@ibpgroup.com.

5 1.3. Product Suitability The application parameters referred to in section 1.2 and the tube compatibility must be adhered to when using and connecting >B< Press copper and brass fittings Drinking water installations Drinking water installations must be planned and operated in accordance with the generally accepted rules of technology, e.g. standards of the EN 806 series, our >B< Press copper and brass fittings have several accreditations for use in drinking water systems. For drinking water applications it is important to select the correct materials. BS EN 806 specifies requirements for drinking water installations that must be adhered to. >B< Press copper and red brass fittings are made from materials that fully comply with European drinking water requirements. >B< Press fittings made of red brass can be combined with stainless steel per EN 10312:2. The use of various materials in a drinking water system complies with technical regulations. Copper, internally tin-plated copper, copper alloys and stainless steel can therefore be combined. >B< Press copper fittings are not suitable for connecting carbon steel tube. However they may be used in a mixed metal system providing the installation is a closed circuit and an oxygen free system (EN14868:2005). >B< Press is also certified by Lloyd s Register for use with water in the ship building industry. 3 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

6 Heating and cooling systems In closed heating systems, there is generally an absence of oxygen which greatly reduces the likelihood of corrosion. Certain corrosion types can occur in systems that are dependent on water quality and poor design. This means simultaneous use of varied metallic materials is possible without any problems; flow control does not need to be taken into consideration. Consequently, >B< Press copper water fittings can be combined with other compatible tube types such as stainless steel, and other materials in a closed system. The same can be used for water cooling systems, providing it relates to a closed system with its own pressure maintenance and without constant entry of oxygen. If constant oxygen entry in the cooling water is to be expected in the systems (for example through an open cooling tower or such), then these pipelines must be treated in a similar way to the requirements for drinking water installations with regards to corrosion protection. Please note a mixed installation is possible only to a limited extent. As applications vary, please contact the technical department for further assistance. Appropriate precautions should be taken in open vented mixed metal systems to avoid any bi-metallic corrosion issues. You must ensure copper is installed downstream from galvanized steel components Local and district heating >B< Press can be used in local and district heating systems with the operating parameters referred to in section 1.2. Please contact our technical team first if special additives need to be added to the hot water for corrosion protection or sealing purposes. For permanent higher operating temperatures above 110 C, it is recommended that you use our >B< Press Solar fittings with the high temperature resistant, green FKM sealing element Thermal solar system with lower operating temperatures >B< Press fittings with a black EPDM O-ring sealant can be used at 110 C in thermal solar systems with low operating temperatures when the operating conditions listed in section 1.2 are adhered to. We recommend the use of >B< Press Solar with the green FKM sealing element for high-temperature systems and other operating conditions. 4. Corrosion Resistance Corrosion and frost protection Copper and copper alloy: Systems containing copper tube with copper and copper alloy fittings generally have a high resistance to corrosion, however it is recommended when systems that have been hydrostatically pressure tested are fully drained down and blown out with dry air. Alternatively if this is impracticable, the system should be left wet, and flushed at regular intervals prior to being commissioned to reduce carbon film cold pitting, corrosion and taking into account any precautions against freezing. This is of importance in new build housing when properties are not occupied for extended periods of time. When using >B< Press copper fittings it is possible external corrosion will increase when contact is made with corrosion causing construction materials or system design errors (exposure to corrosive environments). For such situations please ensure all measures have been implemented to ensure the system is protected. Oxygen entry cannot always be fully prevented in extensive tube systems. EN 806 part 2 and 4 provide instructions for the measures to be taken in this case (chemical oxygen binding). All chemical additions must be agreed before use to rule out negative interactions with materials and sealing elements (O-rings). If the use of a frost protection device is necessary, >B< Press fittings can be used with glycol-water mixtures up to a mixing ratio of 50:50 without affecting the product quality and the sealing element. If frost protection is meant to remain in the pipelines permanently, at least one concentration test must be carried out annually. For more information please contact our technical team on +44 (0)

7 1.4.2 System commissioning Water systems containing tube and fittings in copper and copper alloy should have a regime of pre-commissioning that does not have any detrimental effect on the longevity of the system. Prior to this commissioning, the system should be pressure tested. The chemicals used in the pre-commissioning, if incorrectly administered can have a serious effect on the systems life, therefore the choice of chemicals is dependent on the particular site conditions and the materials used and the method(s) of construction. Conex Bänninger do not recommend specific commercial products, but issue guidelines on a selection of chemicals available that are, if used correctly, suitable for copper fittings. In all cases these chemicals must be stored, handled, and ultimately disposed of (including flushing water) in a safe manner. Taking into consideration current regulations such as COSHH (control of substances hazardous to health regulations), and the Health and Safety at Work act in their current forms. The selection of chemical(s) may also be influenced by approval from the local water authorities, before chemicals are flushed or drained. Temporary mains supply(s) should be cleaned and chlorinated in accordance with BS 8558 before being used for system filling and flushing. Alternative sources such as fire hydrants should only be used with prior approval. If the permanent mains supply is used, connection should be made via a verifiable backflow preventer (RPZ valve assembly) in accordance with the Water Supply (water fittings) Regulations Commercially available chemicals that contain the corrosion and scale inhibitors as constituents listed below will depend on the components of the installed system. Their concentrations will depend on the system volumes, and dilution recommended by the supplier Chemical types, and their function(s) found in commercial products. Component Nitrite Nitrate Molybdate Azoles Phosphate Polyphosphate Phosphonates Silicates Tannins Benzoate Triethanolamine, monoethanolamine, alkylcarboxylates and substituted triazines Phosphono - and phosphino - carboxylic acids Diethylhydroxylamine Borate Inhibitor function Corrosion inhibitor for ferrous metals Corrosion inhibitor for aluminiums Corrosion inhibitor Corrosion inhibitor for copper and copper alloys Corrosion inhibitor for steel Scale and corrosion inhibitor (Reverts to Orthophosphate) Scale and corrosion inhibitor Corrosion inhibitor for steel, copper alloys, and aluminums Film forming corrosion inhibitor and oxygen scavenger Anodic inhibitor Organic film formers and corrosion inhibitors Cathodic inhibitor and scale dispersant Oxygen scavenger ph buffer, biocide, and corrosion inhibitor 5 Ongoing water treatment should be provided by an accredited third party that specialises in that area of expertise. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

8 Additional recommendations for the prevention of corrosion on copper and copper alloys When metallic systems are pressure tested using water as a test media and subsequently drained down, this can affect the longevity of that system if precautions are not undertaken. Certain chemical processes rely on the flow of water to achieve a protective patina on the interior of the tube and fittings. Stagnant areas can increase the potential for localised corrosion. Systems containing copper tube with copper and copper alloy fittings generally have a high resistance to corrosion, however it is recommended when systems that have been hydrostatically pressure tested are fully drained down and blown out with dry air. Alternatively if this is impracticable, the system should be left wet, and flushed at regular intervals prior to being commissioned to reduce carbon film cold water pitting, taking into account any precautions against freezing. This is of importance in new build housing when properties are not occupied for extended periods of time. The use of commercial anti-corrosion chemicals is not to be used on potable water systems, due to the nature of these chemicals. Hydrostatic test pressures are generally 1.5 times the maximum operation pressure, and should be applied slowly to the system. Precautions should be taken to prevent potential legionella increases in systems with stagnant water. If commercial leak detector aerosols are used to detect leaks, it is recommended the residue is washed off with clean, warm water Flushing of water installations It is essential to flush the systems with water after installation to remove dust, debris and flux residues. Please note In the absence of UK national guidelines commissioning should be carried out in accordance with EN If installations are not used immediately after commissioning they should be flushed at regular intervals, at least once a week. After an extended time, it would be recommended the system is disinfected to comply with Legionella guidelines Testing and commissioning drinking water installations When the installation is complete, and after flushing, it should be slowly filled with water at ambient temperature, with the highest draw-off point open to allow air to be expelled from the system. The installation should then be inspected for leaks and remedial action taken if necessary. Drinking water system installations should be tested and inspected in accordance with national guidelines. Hydrostatic test pressures are generally 1.5 times the maximum operating pressure, and should be applied slowly to the system. For >B< Press fittings the hydrostatic pressure should be raised slowly and checked at intervals to detect any unpressed joints. Care should be taken in regard to the potential of Legionella in systems with stagnant water. All the above systems can be tested pneumatically, but the air must be clean, dry, and oil free (oil can have damaging effects on EPDM seals in certain types of fittings, such as press and push fit). Care must also be taken with regard to pneumatic test pressures. 3.0 bar should be sufficient for most systems as air is more searching than water. Higher pressures are potentially dangerous due to the stored energy in compressed air/gas systems HSE guidance should be observed. If commercial leak detector aerosols are used to detect leaks, it is recommended the residue is washed off with clean, warm water. Please contact technical for further assistance. For chlorination please refer to document "pre-commisioning of systems" available at General comments for all systems: The use of commercial anti-corrosion chemicals is not to be used on potable water systems, due to the nature of these chemicals Water softening Hard water may be softened to avoid excessive deposits of scale in hot water services. However, a degree of scale is necessary to form the protective patina on copper tube. When a new copper tube installation has a water softener fitted from day one, it is good practice to run the system for approximately three months with the softener by-pass open to allow untreated water into the system, and allow the patina to form. Ideally the system should be around 60 ppm of total hardness.

9 1.5: Thermal Expansion Effects of expansion The coefficient of linear expansion for copper is 16.8 x 10-6 C. For example, a 10m length of copper tube, irrespective of its size, wall thickness or temper, will increase in length by a temperature rise of 60 C. Tubes installed on hot water services must be free to accommodate this expansion; otherwise stresses will build up in the pipework that may lead to joints being pulled apart and/or tubes fracturing. Clearly the magnitude and frequency of such changes in length will determine the life of the joint or failure of the tube. Table 5.2 shows the amount of tube expansion for a given temperature rise. In the case of tube in domestic hot water and heating installations the limited size of rooms and hence straight tube runs, together with the many bends and offsets that normally occur, will result in thermal movement being accommodated automatically. However where long straight tube runs, exceeding 10 m, are encountered, allowance for expansion should be made. A quick, economic and effective way of accommodating thermal expansion is to simply incorporate the horseshoe or compensating bend to the system design Expansion devices By change of direction Where copper tubes pass through walls, floors and ceilings, they should be able to move as a result of expansion and contraction. This can be arranged by passing the tube through a sleeve or length of larger diameter tube fixed through the whole thickness of the wall, floor, ceiling, or by means of flexible joints on either side of the wall. Tube length m Horseshoe or compensating bend Short stubs to and from radiators, connected to relatively long straight runs should also be avoided. This can usually be achieved by introducing an expansion loop, thereby increasing the length of pipework fixed between the flow/return legs and the radiator connection. However, expansion accommodation techniques such as the use of loops and horseshoes may not be sufficient to accommodate large expansions and in such cases the use of the bellows type couplers may be necessary. Thermal expansion (mm) of copper tube as a function of tube length and temperature difference. The table below shows the increase in length due to thermal expansion as a function of change in temperature t and the length of the tube at the lower temperature, irrespective of temper or wall thickness. Temperature difference t C t=30 t=40 t=50 t=60 t=70 t=80 t=90 t= Δ t dimensional increase is stated in mm 7 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

10 1.6. Loss Coefficients Symbol Designation Application DW H Symbol Designation Application DW H Angle or elbow reference value in accordance with DIN 1988 T3 0,70 Distributor outlet 0,5 Collective inlet 1,0 Angle 90 r/d = 0,5 (r/d = 1,2 = 1,0 with fittings = 2,0 complying with DIN EN 1254) = 3,0 1,0 0,35 0,20 0,15 Reservoir outlet 0,5 Inlet 1,0 Angle ß = 90 = 60 = 45 1,3 0,8 0,4 Reducer 0,4 Crossover 0,5 Constriction ß - constant = ,02 0,04 0,07 8 Branch, square flow separation 1,3 Flow merging 0,9 Expansion ß - constant = ,10 0,15 0,20 0,20 Clearance at flow merging 0,3 Expansion bends 1,0 Clearance at flow merging 0,6 Counter- flow at flow merging Counter-flow at flow separation 3,0 1,5 Compensator 2,0 Compensator 2,0

11 Symbol Designation Application Branch, curved flow separation DW H 0,9 Flow merging 0,4 Symbol Designation Application Shut-off valve Straight seat valve DN15 DN20 DN25 DN32 DN40 to DN100 10,0 8,5 7,0 6,0 5,0 DW H Clearance at flow separation 0,3 Clearance a flow merging 0,2 Angle seat valve DN 15 DN20 DN 25 to DN50 DN65 3,5 2,5 2,0 0,7 Angle valves DN 10 DN 15 DN 20 to DN 50 DN 65 to DN 100 7,0 4,0 2,0 3,5 4,0 Return flow inhibitor DN 15 to DN 20 DN 25 to DN 40 DN 50 DN 65 to DN 100 7,7 4,3 3,8 2,5 Diaphragm valves DN 15 DN 20 DN 25 to DN 32 DN 40 to DN ,0 8,5 7,0 6,0 5,0 Control valve with return flow inhibitor DN 20 DN 25 to DN 50 6,0 5,0 9 Shutter valves Piston valves Ball valves DN 10 to DN 15 DN 20 to DN 25 DN 32 to DN 150 1,0 0,5 0,3 Valve tapping sleeve DN 25 to DN 8O 5,0 Radiator valves 4,0 Boiler 2,5 Control valve 2,0 Heating radiator 2,5 Pressure regulator fully open 30,0 Panel radiator 3,0 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

12 10 >B< Press 12-54mm copper

13 2.1. >B< Press Copper Fittings 12-54mm >B< Press fittings are quick and easy to install and are available in copper and red brass. This flame-free fitting is designed with an innovative 3-point press system to ensure a leak-free, secure and permanent joint and are suitable for multiple applications Fitting Construction Fitting construction 12-54mm The >B< Press copper and red brass design has the advantage of a 3-point press profile; two hexagonal mechanical presses on either side of the bead, and one press on the O-ring. When pressure is exerted through the press tool, the O-ring material compresses itself to form a permanent, leak-proof joint, as a part the cold forming process. This 3-point press feature enables a quick and safe installation process. All our >B< Press copper and brass fittings have a 'leak before press indicator that highlights un-pressed connections at low pressure. >B< Press copper and brass fittings are specifically designed with a high-quality EPDM seal, with a specially designed section in two positions, which allows leakage if the joint has not been pressed. The joint will leak at a pressure between 0.1 to 6.0 bar. Any unpressed joints can be identified during the test phase and corrected, saving valuable time and money. There is no need to drain down as the pressing operation can be carried out whilst the water is still in the system. When the fitting is pressed, the O-ring material compresses itself to form a permanent, leak-free joint Product Suitability Compressed air systems >B< Press fittings with the black EPDM O-ring seal can be used in oil free compressed air systems under the conditions referred to in section 1.2. We recommend the use of our >B< Press Solar fittings with the green FKM sealing element or the >B< Press Gas fittings with the yellow HNBR sealing element for use in oil-containing compressed air systems. Please refer to product suitability under the general section, for more information >B< Press Tools >B< Press jaws There are various press machines and jaws that have been tested for use when installing the >B< Press fitting system. Note: we offer press jaws in sizes 12-54mm. See approved press jaws listed in section For a guaranteed leak-free joint you must use our approved and recommended pressing jaws, see section >B< Press copper and brass fittings are installed using a mechanical press tool with a compatible >B< profile or V profile jaw. Jaws are sized to match the fitting required. When force is exerted through the press tool the jaw closes to make a permanent joint. Please refer to our approved list of press machines and jaws in section For more details please refer to the tool manufacturers guarantee. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

14 2.4.2 Maintenance 12-54mm The maintenance and inspection of press machines and jaws for sizes below 54mm must be carried out at least once a year, or at the latest after approximately 10,000 pressings, or as specified by the press tool manufacturer. For sizes above 54mm this must be carried out prior to each use to ensure they are clean and free from debris and dirt. Maintenance, care and cleaning of press jaws must be done by the user. Press jaws must always be free of damage and deformation. The inner pressing contour of the jaw must always be kept free of dirt and debris. When necessary, the jaws can be cleaned with a brush or cleaning cloth and non-corrosive solvents such as methylated spirit. The pressing jaws should be visually inspected to ensure there are no cracks to avoid potential injury from flying fragments if it shatters. When inspecting the pressing jaws, also ensure that there are no foreign material deposits and that the contours of the jaw surfaces are in order. Note: Please make sure maintenance is done regularly or this may result in damage to the press machine and jaws. Always remove the battery from the press machine before cleaning. For tool and jaw maintenance please refer to the manufacturers instructions. 12

15 2.4.3 Compatible press tools Size and type Press jaw IBP Klauke Rems ROTHENBERGER Viega RIDGID 12-54mm Profile 32KN press machines >B< Press >B< Press Gas >B< Press Solar >B< Press Inox >B< Press Carbon Manufacturer IBP Klauke Rems Press machine KSP4 P77267 SSK (42 & 54 only) Conel Novopress* Milwaukee* V/V45 V/SV SOM PT 2 v V-PB2 UP2EL14 UAP2/UNP2 UAP3L/UAP4L Power-Press No Akku-Press No Romax 3000 ROTHENBERGER Romax Pressliner/Eco Romax AC-Eco Typ 2 Viega PT3-AH/EH/H Akku-Presshandy Pressgun 5/4 B/E Conel PM 2 EFP1 (as of serial nr.6000) EFP2 Novopress ACO1/ECO1 ACO/ECO/EFP/AFP201/202 ACO/ECO/EFP203 Milwaukee M18 HPT/BLHPT 13 Geberit PWH 75 RIDGID RP 330/340-B/-C Size and type IBP Rems ROTHENBERGER Viega RIDGID 12-35mm KSP4 P77282 Compact press machines IBP Klauke Mini V/V45 Conel Novopress* Milwaukee* Compact Picco Compact V-PB1 MAP1 28 No No No No No MAP2L 28 No No No No No >B< Press >B< Press Gas >B< Press Solar >B< Press Inox >B< Press Carbon Rems Mini-Press ACC No No No No No ROTHENBERGER Romax Compact No No 28 No No 28 RIDGID 100-B / RP 210-B No No No No No Viega Picco/Pressgun Picco No No No No No Conel PM1 No No 28 No No Novopress AFP101/ACO102 No No 28 No No Milwaukee M12 HPT No No 28 No No! Always read the manufacturers instruction book before using press machines and jaws. * NOVOPRESS & MILWAUKEE Jaws with the marking only Use of tools If other machines and press jaws are used, their suitability for a permanent tight connection must be demonstrated by an accredited test. A constant thrust of at least 32 KN and max. 36 KN is a pre-requisite to ensure that sufficient power reserves for the dimension of 54mm are available, and that high shear forces cannot reduce the lifetime of the pressing jaws or destroy them. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

16 2.5. Installation Requirements Installation dimensions L A D E Size External-Ø pressing Minimum Minimum Insertion bead distance tube length depth mm D - mm A - mm L - mm E - mm Due to reforming of the tube profile when pressed, it is advised that a minimum distance is allowed between each fitting Space required for the pressing process 14 The following minimum clearances are required from structural components to allow operation of tool for press fitting. Y Y2 Y1 Space required for the pressing process between pipes External pipe Y Size mm mm mm Space required for the pressing process between tubes External pipe Y1 Y2 Size mm mm mm mm

17 2.5.3 >B< Press tube sizing compatibility Due to reforming of the tube profile when pressed, it is advised that a minimum distance is allowed between each fitting.2. Copper tube to EN1057 Tube O/D Temper R220 Temper R250 Temper R290 Wall thickness (mm) Wall thickness (mm) Wall thickness (mm) Localised annealing To ensure proper sealing of both the brazed and >B<Press fitting, the following minimum distances must be maintained between the two fittings. Please see table A for further information. Minimum distance Tube size D E F G Size mm mm mm mm mm Brazing near >B< Press fittings Caution: Brazing or soldering near to >B< Press joints should be avoided as this may cause the seal to degrade due to heat transfer. The table to the right states the minimum distance away from the press joint which is acceptable to braze. If this distance cannot be maintained then adequate precautions must be taken such as fabricating the brazed section prior to assembly with the press fittings, wrapping in a wet rag or applying a hot block, to prevent heat transfer to the press fitting during brazing. Tube size Minimum clearance F mm mm This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

18 2.6. >B< Press Installation Process It is advisable to leave the fittings in the packaging prior to final installation to protect them from contamination and to conserve the lubrication of the O-rings. Please note the space required for pressing tools (see section 2.5.2) Cutting to length Deburring and calibrating Checking the fittings Use a rotary tube cutter. Ensure that the tube is cut square. Deburr the tube both internally and externally. Check the fitting is the correct size for the tube. Check the pipe has retained its shape and is damage free. Where possible angle the tube downwards to prevent filings entering the tube. Check the O-rings are present and correctly seated. Make sure the internal and external surfaces of the tube ends are smooth and free from burrs or sharp edges. Additional lubricant (silicon oil) may be used to aid tube insertion Marking the insertion depth Assembling the tube and fitting Complete the joint with the press tool The tube must be fully inserted into the fitting until it reaches the tube stop. Insert the tube fully into the fitting up to the tube stop. Ensure pipework is correctly aligned prior to pressing. To reduce the risk of dislodging the O-ring rotate the tube (if possible) while slipping it into the fitting. To reduce the risk of dislodging the O-ring rotate the tube (if possible) while slipping it into the fitting. Ensure the correct size jaw is inserted into the tool. Mark the insertion depth on the tube. Prior to pressing ensure the tube has not moved out from the fitting socket. Use the insertion depth mark as a guide. The jaws must be placed squarely on the fitting, locating the groove on the bead. The bead on the fitting should fit centrally in the groove of the jaw. Caution: The >B< Press joint is complete after one full cycle of the tool. Do not crimp any >B< Press fitting more than once.

19 2.7. The Range Straight Coupler P5270 Slip Coupler P4275 Fitting Reducer P5243 Male Straight Connector P4243G 90 Bend P Bend with Female Thread P4090G 90 Street Bend P5001 Female Straight Connector P4270G Obtuse Elbow P Obtuse Street Elbow P Bend with Male Thread P4001G Equal Tee P5130 Tee with Female Thread Branch P4130G Reduced Tee Branch P5130 Stop End P5301 Fitting Lubricant MPABPSOIL100ml This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

20 P5270 Straight Coupler Dimension L Z Product code P P P P P P P P P4275 Slip Coupler Dimension L Product code P P P P P P P P P5240 Reduced Straight Coupler Dimension L Z Product code 15 x P x P x P x P x P x P x P x P P5243 *All above measurements are in mm unless stated differently. Fitting Reducer Dimension L Z L1 D Product code 15 x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P

21 P4243G Male Straight Connector Dimension L S Z Product code 12 x 3/8" P4243G x 1/2" P4243G x 3/8" P4243G x 1/2" P4243G x 3/4" P4243G x 1/2" P4243G x 3/4" P4243G x 1/2" P4243G x 3/4" P4243G x 1" P4243G x 3/4" P4243G x 1" P4243G x 1 1/4" P4243G x 1" P4243G x 1 1/4" P4243G x 1 1/2" P4243G x 1 1/4" P4243G x 1 1/2" P4243G x 1 1/2" P4243G x 2" P4243G P4270G Female Straight Connector Dimension L S Z L1 Product code 12 x 3/8" P4270G x 1/2" P4270G x 3/8" P4270G x 1/2" P4270G x 3/4" P4270G x 1/2" P4270G x 3/4" P4270G x 1/2" P4270G x 3/4" P4270G x 1" P4270G x 3/4" P4270G x 1" P4270G x 1 1/4" P4270G x 1" P4270G x 1 1/4" P4270G x 1 1/4" P4270G x 1 1/2" P4270G x 2" P4270G *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

22 P4331G Male Straight Union Connector (ISO 7 R) Dimension L S1 S2 Z Product code 12 x 3/8" P4331G x 1/2" P4331G x 1/2" P4331G x 3/4" P4331G x 1/2" P4331G x 3/4" P4331G x 1/2" P4331G x 3/4" P4331G x 1" P4331G x 1" P4331G x 1 1/4" P4331G x 1 1/2" P4331G x 2" P4331G P4330G Female Straight Union Connector (ISO 7 Rp) Dimension L S1 S2 Z Product code 12 x 1/4" P4330G x 1/2" P4330G x 3/4" P4330G x 1/2" P4330G x 3/4" P4330G x 3/4" P4330G x 1" P4330G x 1" P4330G x 1 1/4" P4330G x 1 1/2" P4330G x 2" P4330G P4280G Male Adaptor with Male Thread (ISO 7 R) Dimension L S L1 Product code 12 x 1/2" P4280G x 1/2" P4280G x 1/2" P4280G x 3/4" P4280G x 1/2" P4280G x 34" P4280G x 1" P4280G x 1 1/4" P4280G x 1 1/2" P4280G x 2" P4280G *All above measurements are in mm unless stated differently.

23 P4281G P5085 NEW Male Adaptor with Female Thread (ISO 7 Rp) Dimension L S Z Product code 12 x 1/2" P4281G x 1/2" P4281G x 1/2" P4281G x 3/4" P4281G x 1/2" P4281G x 3/4" P4281G x 3/4" P4281G x 1" P4281G x 1" P4281G x 1 1/4" P4281G x 1 1/2" P4281G x 2" P4281G Crossover Coupler Dimension L Z H Product code P P P P Crossover Coupler Dimension L Z H Product code P P P P P4355 Connector with Flat Sealing Face (ISO 7 Rp) Dimension L Z S Product code 15 x 3/4" P x 3/4" P x 1" P x 1" P x 1 1/2" P x 1 3/4" P x 2 3/8" P P Bend Dimension L Z Product code P P P P P P P P *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

24 P Obtuse Elbow Dimension L Z Product code P P P P P P P P P4001G 90 Bend with Male Thread (ISO 7 R) Dimension L L1 Z Z1 S Product code 12 x 3/8" P4001G x 1/2" P4001G x 3/8" P4001G x 1/2" P4001G x 1/2" P4001G x 3/4" P4001G x 3/4" P4001G x 1" P4001G x 1 1/4" P4001G x 1 1/2" P4001G x 2" P4001G P4096G 90 Bend with Female Thread (ISO 7 Rp) and Threaded Union Dimension L L1 S1 S2 Z Z1 Product code 12 x 1/2" P4096G x 1/2" P4096G x 1/2" P4096G x 3/4" P4096G x 3/4" P4096G x 1" P4096G x 1" P4096G x 1 1/4" P4096G x 1 1/2" P4096G x 2" P4096G P4471G Wallplate Elbow (3 Hole) with Female Thread (ISO 7 Rp) Dimension L L1 d Z Z1 Product code 12 x 1/2" P4471G x 1/2" P4471G x 1/2" P4471G x 1/2" P4471G x 1/2" P4471G x 3/4" P4471G *All above measurements are in mm unless stated differently.

25 P º Street Elbow Dimension L L1 Z Product code P P P P P P P P P Obtuse Street Elbow Dimension L L1 Z Product code P P P P P P P P P5130 Equal Tee Dimension L Z L1 Z1 Product code P P P P P P P P P4132G Tee with Male Threaded Branch (ISO 7 R) Dimension L L1 Z Product code 15 x 3/4" x P4132G x 3/4" x P4132G x 3/4" x P4132G x 3/4" x P4132G x 3/4" x P4132G x 3/4" x P4132G x 1" x P4132G x 1 1/4" x P4132G *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

26 P5130G Tee with Female Threaded Branch (ISO 7 Rp) Dimension L L1 Z Z1 S Product code 12 x 12 x 1/ P4130G x 15 x 3/8" P4130G x 15 x 1/2" P4130G x 18 x 1/2" P4130G x 22 x 1/2" P4130G x 22 x 3/4" P4130G x 28 x 1/2" P4130G x 28 x 3/4" P4130G x 35 x 1/2" P4130G x 42 x 1/2" P4130G x 54 x 1/2" P4130G P5130 Reduced Tee Branch Dimension L Z L1 Z1 Product code 15 x 12 x P x 12 x P x 15 x P x 12 x P x 15 x P x 18 x P x 15 x P x 18 x P x 22 x P x 15 x P x 18 x P x 22 x P x 28 x P x 22 x P x 28 x P x 35 x P x 22 x P x 28 x P x 35 x P x 42 x P P5130 Reduced Tee Both Ends Dimension L Z L1 Z1 L2 Z2 Product code 12 x 15 x P x 18 x P x 22 x P x 22 x P x 28 x P *All above measurements are in mm unless stated differently.

27 P5130 Reduced Tee End And Branch Dimension L Z L1 Z1 L2 Z2 Product code 15 x 12 x P x 15 x P x 15 x P x 15 x P x 18 x P x 18 x P x 15 x P x 18 x P x 22 x P x 22 x P x 28 x P x 35 x P x 54 x P P5130 P5301 Tee Reduced End Dimension L Z L1 Z1 L2 Z2 Product code 15 x 15 x P x 18 x P x 22 x P x 22 x P x 28 x P x 28 x P x 28 x P Stop End Dimension L L1 Product code P P P P P P P P P4060G NEW Looped Wallplate Dimension L Z L1 Product code P4060G P4060G P4060G *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

28 26 >B< Press L mm copper

29 3.1. >B< Press L Copper Fittings mm EPDM seal Stainless steel grip ring The action of the pressing ring closes the joint and forces the grip ring teeth into the tube making a high strength connection. >B< Press L fitting Fitting bead Copper tubing Product features >B< Press L has only two internal parts, the grip ring and the seal. Both parts have an internal diameter larger than the tube, which allows for easy tube insertion and pre-press leak indication Stainless steel grip ring Complete diameter grip ring ensures all round equal grip on the tube diameter, and even seal compression between tube and fitting after pressing Seal design Triple point seal on the pressed fitting body counters any pressing distortion and gives greater seal contact area on the tube. Self setting seal area for correct function of seal. Seal security and longevity increased as a result. 27 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

30 28

31 D B E 3.2. Installation Requirements Installation dimensions Refer to in the >B< Press section. Size D E F G mm mm mm mm mm Space required for the pressing process Refer to in the >B< Press section. The following minimum clearances from structural components are required to allow operation of tool for press fitting. Minimum clearance Size A B C D E mm mm mm mm mm mm A C >B< Press tube sizing compatibility Copper tube to EN1057 Tube O/D Temper R220 Temper R250 Temper R290 Wall thickness (mm) Wall thickness (mm) Wall thickness (mm) * 2.5 *108 x 1.5mm - Additional requirement over EN1057 for the minimum wall thickness must not be taken below 1.4mm This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

32 3.2.4 Pipework protection Copper has a high resistance against corrosion. However, in some cases external protection may be necessary against corrosive conditions. Refer to EN for full pipework protection requirements. Please refer back to the corrosion protection document available on Localised annealing To ensure proper sealing of both brazed and >B< Press fittings, the following minimum distances must be maintained. Please see table A for further information Brazing near >B< Press fittings Caution: Brazing or soldering near >B< Press joints should be avoided as this may cause the seal to degrade due to heat transfer. Table B below states the minimum distance away from the press joint acceptable to braze. If this distance cannot be maintained then adequate precautions must be taken such as fabricating the brazed section prior to assembly with the press fittings, wrapping in a wet rag or applying a hot block, to prevent heat transfer to the press fitting during brazing. Table A Table B Tube size Minimum clearance F Tube size Minimum clearance F mm mm mm mm

33 3.3. >B< Press L Tools Tool chart Size and type >B< Press L Copper (*Please contact technical for other tool suitability) Manufacturer Press jaw Rems ( mm) Viega (64-108mm) Profile VF PT2 Press machine Rems Power-Press Rems Akku-Press Ridgid Rp 340 Viega Pressgun 5 Viega Pressgun 4E/4B Viega Type PT3-AH Viega Type PT3-H/EH Viega Type 2 (PT2) Operating instructions - tool and jaw Only operate the press tool and jaws as per instructions in your User Operating Manual - Instructions for Use. Proper usage includes compliance with the operating manual, inspection and servicing conditions, and adherence to all relevant safety regulations. The equipment must only be used by a qualified trade person who has trained understanding on how to use the press tool and jaw system properly. Failure to do so will lead to safety risk, poor workmanship, and incorrect use of the press tool and jaw that is not covered under warranty. Only use press tools and jaws with compatible press fittings that have been tested and approved in accordance with the Conex Bänninger tool compatibility chart. Always start with a safety check, reminding yourself of the emergency stop button to deactivate a press cycle. Charge battery fully before first use for optimal number of presses per charge. To avoid injury, open the sling removing the actuator and separating the segments of the sling. Fully engage the start button for a full press cycle. Activate the press tool and jaw only on a fitting. Take time to ensure the correct pipe preparation cut pipe square, deburr and calibrate pipe edge and mark insertion depth. These pipe preparation steps are critical for a correct press and quality workmanship. Follow all installation instructions supplied by the fitting and pipe manufacturers. Imperfect pipe joints must only be pressed again using a new fitting. DO NOT re-press the same fitting. During the press cycle, visually check that the press jaw fully closes at the end of the press cycle. After pressing, check the installation with appropriate testing equipment and ensure it is leak proof Maintenance mm Maintenance must be carried out prior to each use to ensure press jaws are clean and free from debris and dirt. Maintenance, care and cleaning of press jaws must be done by the user. Press jaws must always be free of damage and deformation. The inner pressing contour of the jaw must always be kept free of dirt and debris. When necessary, the jaws can be cleaned with a brush or cleaning cloth and non-corrosive solvents such as methylated spirit. The pressing jaws should be visually inspected to ensure there are no cracks to avoid the potential injury from flying fragments if it shatters. When inspecting the pressing jaws, also ensure that there are no foreign material deposits and that the contours of the jaw surfaces are in order. Note: Please make sure maintenance is done regularly or this may result in damage to the press machine and jaws. Always remove the battery from the press machine before cleaning. For tool and jaw maintenance please refer to the manufacturers instructions. 31 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

34 32

35 3.4. >B< Press L Installation Process To install >B< Press L, a mechanical tool with actuator and compatible sized jaw to fit each size fitting is required. When pressure is exerted through the press tool a permanent joint is made and the fitting cannot be disassembled or reused Cutting to length Deburring and calibrating Checking the fittings Marking the insertion depth We recommend you use a ROTHENBERGER pipe cutter. It is important to ensure that the pipe is cut completely square. Tube ends should be clean and free from scratches no less than the socket length. Make sure that the internal and external tube end is free from burrs or sharp edges by using a file or deburring tool. Then wipe the tube end clean to avoid damaging the seal on tube insertion. Before inserting the tube check seal for correct placement, free of damage or any ingress of debris. To prevent this occurring we recommend the fittings are retained in packaging up to the point of use. The tube must be fully inserted into the fitting until it reaches the tube stop in order to make a perfect joint. Marking insertion depth will ensure that any tube movement is detected, which is especially important if the joints are to be pressed at a later time. The depth marking must be visible on the pressed fitting Fit the pressing ring Engage the actuator and check insertion depth Press the joint Joint completion 33 Using the appropriate size pressing ring, open the pressing ring, locate on the fitting bead and close the pressing ring. With the actuator fitted in the press tool open the actuator and locate the actuator onto the aperture of the pressing ring. Check for any tube movement prior to pressing. Depress and hold the trigger of the tool until the press cycle of the tool is automatically completed. Keep hands clear of the press actuator and press ring until the cycle is completed. Remove the actuator from the press ring, remove the press ring from the tube and remove the label to indicate the joint is pressed and complete. Important It is important to keep the fitting free of any dust or dirt, and to ensure the seal stays lubricated and protected from damage. Select the correct size of tube and fitting for the job. Ensure that both are clean and free from damage and imperfections. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

36 3.5. The Range Straight Connector P5270 Repair Coupling P5275 Fitting Reducer P5243 Male Threaded Straight Connector P5243G Threaded Female Straight Connector P5270G 90 Elbow P Street Elbow P Elbow P Street Elbow P5040 Tee P5130 Tee Reduced Branch P5130 Tee with Female Threaded Branch P5130G End Cap P5301 PN16 Flange P5230B 34

37 P5270 Straight Connector Dimension L Z Product code P P P P P P5275 Repair Coupling Dimension L Product code P P P P P P5243 Fitting Reducer Dimension D L L1 Z Product code 64 x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P x P *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

38 P5243G Male Threaded Straight Connector Dimension L Z S Product code 64 x 2 1/2" P5243G x 2 1/2" P5243G x 2 1/2" P5243G x 3" P5243G x 3" P5243G x 4" P5243G P5270G Threaded Female Straight Connector Dimension L L1 Z S Product code 64 x 2 1/2" P5270G x 2 1/2" P5270G x 2 1/2" P5270G x 3" P5270G x 3" P5270G x 4" P5270G P Elbow 36 Dimension L Z Product code P P P P P P Street Elbow Dimension L L1 Z Product code P P P P P *All above measurements are in mm unless stated differently.

39 P5041 Elbow 45 Dimension L Z Product code P P P P P P Street Elbow Dimension L L2 Z Product code P P P P P P5130 Equal Tee Dimension L L1 Z Z1 Product code P P P P P5R P5301 End Cap Dimension L Z A S Product code /4" 31 P /4" 31 P /4" 31 P /4" 31 P /4" 31 P *All above measurements are in mm unless stated differently. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

40 P5130 Tee Reduced Branch Dimension L L1 Z Z1 Product code 64 x 35 x P x 42 x P x 54 x P x 28 x P x 35 x P x 42 x P x 54 x P x 28 x P x 35 x P x 42 x P x 54 x P x 64 x P x 66.7 x P x 54 x P x 64 x P x 76.1 x P x 54 x P5R x 64 x P5R x 76.1 x P5R x 88.9 x P5R P5130G Tee with Female Threaded Branch Dimension L L1 Z Z1 S Product code 64 x 3/4" x P5130G x 1" x P5130G x 2" x P5130G x 3/4" x P5130G x 2" x P5130G x 3/4" x P5130G x 2" x P5130G x 3/4" x P5130G x 2" x P5130G x 3/4" x P5RG x 2" x P5RG P5230B PN16 Flange Dimension L1 L2 L3 Z D1 k n d Product code P5230B P5230B P5230B P5230B P5230B *All above measurements are in mm unless stated differently.

41 4. Guarantee When professionally installed, used and maintained in accordance with the installation and maintenance instructions detailed in the >B< Press and >B< Press L technical brochure, Conex Universal Ltd. guarantees that >B< Press and >B< Press L as supplied by Conex Universal Ltd. will be free of material defects resulting from errors in manufacture, for twenty five (25) years from the date of first purchase by an end user. This Guarantee is limited to the repair or replacement of defective product(s) (at the sole discretion of Conex Universal Ltd.). At the request of Conex Universal Ltd. the allegedly defective product(s) must be returned to the address below** and Conex Universal Ltd. reserves the right to inspect and test the alleged defects. This guarantee provided by Conex Universal Ltd. does not affect your statutory rights. The Guarantee set out is given by Conex Universal Ltd. and subject to the following conditions: A. Any alleged defects must be reported to Conex Universal Ltd. within one month of the first occurrence of any such alleged defect, clearly setting out the nature of the claim and the circumstances surrounding it. B. Conex Universal Ltd. shall be under no liability in respect of any defect in any product arising from: defective installation, fair wear and tear, wilful damage, negligence of any party other than Conex Universal Ltd., abnormal working or environmental conditions, failure to follow the instructions of Conex Universal Ltd., misuse (which includes any use of the product(s) concerned for a purpose or in a situation / environment or for an application other than that for which it was designed), or alteration or repair of any product without the prior approval of Conex Universal Ltd. C. At the request of Conex Universal Ltd. the person claiming under this guarantee must deliver to Conex Universal Ltd. written evidence of the date of first purchase by an end user of the product(s) concerned. 39 ** The address for returns is: Customer Services. Conex Universal Limited, Global House, 95 Vantage Point, The Pensnett Estate, Kingswinford, West Midlands, DY6 7FT, UNITED KINGDOM This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

42 40 Notes

43 Notes 41 This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries.

44 Sonic United Kingdom Conex Universal Limited Spain/France IBP Atcosa SL Poland Sales, Marketing and logistics IBP Instalfittings Sp z.o.o. Germany IBP GmbH Italy IBP Bänninger Italia srl China IBP China USA IBP LLC Tel: +44 (0) Fax: +44 (0) Website: The content of this publication is for general information only. It is the user s responsibility to determine suitability of any product for the purpose intended and reference should be made to our Technical Department if clarification is required. In the interests of technical development we reserve the right to change specification, design and materials without notice. Conex Bänninger products are approved by numerous Standards Authorities and Certification Bodies. For more details on this product range, please our technical team: technical@ibpgroup.com. This is a representation of the full range from Conex Universal Ltd. IBP trademarks are registered in numerous countries. CB/UK/12.18