Mixed Exchange Resins, Strong Acid Resin in Hydrogen Form and Strong Base Resin in Hydroxide Form PRODUCT NAME:

Transcription

1 SECTION 1: PRODUCT AND COMPANY INFORMATION SAFETY DATA SHEET PRODUCT TYPE: Mixed Exchange Resins, Strong Acid Resin in Hydrogen Form and Strong Base Resin in Hydroxide Form PRODUCT NAME: TM-9 family, including TM-9, TM-9SGand TM-9XRR. COMPANY ID: Evoqua Water Technologies LLC 181 Thorn Hill Drive, Warrendale, PA TELEPHONE NUMBER: INFORMATION: CORPORATE MEDICAL EMERGENCY: CHEMTREC TRANSPORTATION EMERGENCY: CHEMTREC DATE PREPARED: June 2, 2015 REVISION: 0 SECTION 2: HAZARD(S) IDENTIFICATION HMIS RATINGS NFPA RATINGS GUIDE HEALTH 1 4 EXTREME/SEVERE 1 3 HIGH/SERIOUS FLAMMABILITY 1 2 MODERATE SLIGHT PHYSICAL HAZARD 0 0 MINIMUM W WATER REACTIVE OX - OXIDIZER PERSONAL PROTECTION E PICTOGRAM SIGNAL WORD HAZARD STATEMENT Warning Causes serious eye irritation. PRECAUTIONARY STATEMENT(S) PREVENTION Wear eye/face protection. Wash hands thoroughly after handling. RESPONSE STORAGE IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. Not applicable. OTHER HAZARDS

2 SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS PERCENT BY WEIGHT COMMON NAME (Ingredient / Component) 35-65% Styrene, divinylbenzene and ethylstyrene copolymer, chloromethyl trimethylamine functionalized in the hydroxide form CAS NO. SAFETY DATA SHEET IMPURITIES % Sulfonated polymer of styrene, ethylstyrene and divinylbenzene in the hydrogen form Balance Water SECTION 4: FIRST-AID MEASURES NECESSARY FIRST AID INSTRUCTIONS INHALATION FIRST AID Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. SKIN CONTACT FIRST AID EYE CONTACT FIRST AID INGESTION FIRST AID: Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Wash clothing before reuse. Clean shoes thoroughly before reuse. Get medical attention. In case of contact, flush eyes with plenty of water for at least 20 minutes. Use fingers to ensure that eyelids are separated and that the eye is being irrigated. Wash out mouth with water. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. DESCRIPTION OF MOST IMPORTANT SYMPTOMS TM-9 family Date 6/2/2015 Rev: 0 Pages 2 of 6

3 RECOMMENDATIONS FOR IMMEDIATE MEDICAL CARE No special measures required. SECTION 5: FIRE-FIGHTING MEASURES SUITABLE EXTINGUISHING MEDIA water spray (fog), foam or dry chemical UNSUITABLE EXTINGUISHING MEDIA SPECIFIC HAZARDS PERSONAL PROTECTIVE EQUIPMENT None known No specific fire or explosion hazard. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. SECTION 6: ACCIDENTAL RELEASE MEASURES PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES PERSONAL PRECAUTIONS Without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. Hazard of slipping on spilled product. ENVIRONMENTAL PRECAUTIONS CONTAINMENT AND CLEAN-UP OTHER INFORMATION Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Move containers from spill area. Approach release from upwind. Avoid dust generation. Do not sweep. Vacuum dust with equipment fitted with HEPA filter and place in a closed, labeled waste container. Dispose of via a licensed waste disposal contractor. Note: see section 1 for emergency contact information and section 13 for waste disposal. Prevent entry into sewers, water courses, basements or confined areas. SECTION 7: HANDLING AND STORAGE PRECAUTIONS FOR SAFE HANDLING Do not ingest. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. Remove contaminated clothing and protective equipment before entering eating areas. Workers should wash hands and face before eating, drinking and smoking. Put on appropriate personal protection equipment. Eating, drinking and smoking should be prohibited in areas where the material is handled, stored and processed. CONDITIONS FOR SAFE STORAGE Store between the following temperatures: 10 to 40 C (14 to 104 F). Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see TM-9 family Date 6/2/2015 Rev: 0 Pages 3 of 6

4 section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers retain. Use appropriate containment to avoid environmental contamination. Empty containers retain products residue and can be hazardous. Do not reuse container. It is recommended to store ion exchange resins at temperatures above the freezing point of water. If the resin should become frozen, the resin should not be mechanically handled and should be left to thaw out gradually at ambient temperature. It must be completely thawed before handling or use. No attempt should be made to accelerate the thawing process. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION ENGINEERING CONTROLS Good general ventilation should be sufficient to control worker exposure to airborne contaminants RESPIRATORY PROTECTION SKIN PROTECTION EYE/FACE PROTECTION Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator Wear suitable protective clothing and gloves. Suitable protective footwear. Safety glasses with side-shields or goggles EXPOSURE LIMITS/GUIDELINES No exposure limit value known. PARTICULATES NOT OTHERWISE REGULATED (PNOR) PARTICULATES NOT OTHERWISE CLASSIFIED (PNOC) RESULT N/A N/A OSHA 8 HR mg/m 3 ACGIH TLV 8 HR mg/m 3 SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES COLOR Black. Brown. [Light] MOLECULAR WEIGHT Not available. ODOR Not available. ODOR THERSHOLD Not available. ph VALUE 6 to 9 [Conc. (% w/w): VAPOR PRESSURE Not available. 10%] MELTING POINT Not available. VAPOR DENSITY Not available. FREEZING POINT Not available. RELATIVE DENSITY 650 to 750 kg/m³ INITIAL BOILING POINT Not available. SOLUBILITY Insoluble in cold water FLASHPOINT Closed cup: >150 C PARTITION COEFFICEINT Not available. (>302 F) EVAPORATION RATE Not available. AUTO IGNITION TEMP. >500 C (>932 F) FLAMMABILITY Not available. DECOMP. TEMP. Not available. UEL Not available. VISCOSITY Not available. LEL Not available. TM-9 family Date 6/2/2015 Rev: 0 Pages 4 of 6

5 SECTION 10: STABILITY AND REACTIVITY REACTIVIVITY No specific test data related to reactivity available for this product or its ingredients CHEMICAL STABILITY The product is stable POSSIBILITY OF HAZARDOUS Under normal conditions of storage and use, hazardous REACTIONS reactions will not occur CONDITIONS TO AVOID No specific data. HAZAROUS DECOMPOSITION PRODUCTS Under normal conditions of storage and use, hazardous decomposition products should not be produced. SECTION 11: TOXICOLOGICAL INFORMATION INHALATION ACUTE CHRONIC SKIN ACUTE CHRONIC EYE ACUTE Causes serious eye irritation. INGESTION ACUTE CHRONIC LD50 LC50 ACUTE TOXICITY ESTIMATES CARCINOGENICITY/MUTAGENICITY REPRODUCTIVE EFFECTS NEUROTOXICITY OTHER EFFECTS TARGET ORGANS >5000 mg/kg Oral (rat) Not applicable. Not available. SECTION 12: ECOLOGICAL INFORMATION The material in its original state, is not harmful to the environment. SECTION 13: DISPOSAL CONSIDERATIONS SPILL/LEAK Isolate spill area to prevent falls as material can be a slipping hazard. Avoid PROCEDURES contact with eyes and skin. Material is heavier than water and has limited water solubility. It will collect on the lowest surface. CLEANUP Clean up floor area. Sweep up. Avoid generation of dust. REGULATORY REQUIREMENTS DISPOSAL If discarded in its purchased form, this product would not be a hazardous waste either by listing or by characteristic. However, under RCRA, it is the responsibility of the product user to determine at the time of disposal, whether a material containing the product or derived from the product should be classified as a hazardous waste. (40 CFR ) The generation of waste should be avoided or minimized wherever possible. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty container or liners may retain some product TM-9 family Date 6/2/2015 Rev: 0 Pages 5 of 6

6 residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Waste disposal should be in accordance with existing federal state, provincial and or local environmental control laws. Observe label precautions SECTION 14: TRANSPORT INFORMATION LAND DOT UN/NA IDENTIFICATION NUMBER: UN-PROPER SHIPPING NAME: TRANSPORT HAZARD CLASS: PACKING GROUP: MARINE POLLUTANT: HAZARD CLASS: WATER IMO/IMDG UN/NA IDENTIFICATION NUMBER: UN-PROPER SHIPPING NAME: TRANSPORT HAZARD CLASS: PACKING GROUP: MARINE POLLUTANT: AIR ICAO/IATA For product quantities less than 0.5 Kg UN/NA IDENTIFICATION NUMBER: UN-PROPER SHIPPING NAME: TRANSPORT HAZARD CLASS: PACKING GROUP: MARINE POLLUTANT: SECTION 15: REGULATORY INFORMATION OSHA OSHA CAA CERCLA SARA SARA HAZARD Immediate (acute) health hazard CATEGORIES 311/312 TSCA SECTION 16: OTHER INFORMATION DISCLAIMER: The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the user thereof. It is the buyer s responsibility to ensure that its activities comply with federal, state, provincial and local laws. REVISION INDICATOR: Revision 0: (This SDS replaces the former MSDS for this product pursuant to OSHA (g) Appendix D. The MSDS for this product should be considered obsolete). TM-9 family Date 6/2/2015 Rev: 0 Pages 6 of 6