OEM Liquid-Flowmeter

Transcription

1 OEM Liquid-Flowmeter (With State-of-the-Art Technology) Rev.: 1.2 Seite 1 / 6

2 OEM-Liquid-Flowmeter Functional Principle The OEM Liquid-Flowmeters are working with ultrasound according to the Time-of-Flight (ToF) technique. Piezoelectric sensors are sending and receiving ultrasonic sound waves. In the direction of flow the sound wave is accelerated and is decelerated against the direction of flow. The difference of both acoustic runtimes is proportional to the flow. Advantages: Maintenance-free No problems with hydraulic shocks and polluted media Widely independent of temperature and electrical conductivity Nearly without any time lag Pulsating flows (e.g. because of use of diaphragm pumps) are possible No moving parts No damage because of too high flows Highest long-term stability Lowest pressure loss Irrespective of its position Detection of flow direction Empty tube and air bubble detection Leakage detection Overview Model Range Brass PPA Nominal Size DN20...DN25 DN15...DN25 Material of Flow Tube Brass PPA GF40 Process Connection Threated Connection Threated Connection Maximum Media Temperature 90 C 50 C Pressure Rating PN16 Signal Output Voltage Output * *Modbus and other signal outputs possible on request Rev.: 1.2 Seite 2 / 6

3 Brass PPA Specifications: Nominal Size DN20 DN25 DN15 DN20 DN25 Process Connection G1 G1¼ G¾ G1 G1¼ Metering Range [l/min] 0, , , ,4 75 0,6 110 Accuracy* ± 1% of reading* t.b.d. t.b.d. t.b.d. t.b.d. Additional Analogue Signal ± 0,1 l/min ± 0,2 l/min ± 0,06 l/min ± 0,1 l/min ± 0,2 l/min t.b.d. Repeatability* ± 0,25 % Response Time < 100 ms Signal above 0,2 l/min 0,3 l/min 0,15 l/min 0,2 l/min 0,3 l/min Media Temperature C C Environmental Temperature C 0 70 C Pressure Rating Electrical Data: Connection Supply Voltage Current Consumption PN16 t.b.d. 24VDC (± 5 %), reverse battery protection < 50 ma Analogue Signal 0,5..5V equals to [l/min] Empty Tube / Leakage Detection Load Resistor of Analogue Output * Water C < 0,3 V > 10 kohm rel. deviation of measured value [%] Typical Gradient , Brass DN20 Q [l/min] 23 C 75 C Rev.: 1.2 Seite 3 / 6

4 Typical Pressure Loss Pressure Loss [mbar] DN15 DN20 DN Flow [l/min] Brass PPA Specifications: Nominal Size DN20 DN25 DN15 DN20 DN25 Process Connection G1 G1¼ G¾ G1 G1¼ L [mm] H [mm] Rev.: 1.2 Seite 4 / 6

5 Ordering Information Article SQ-Flow-KSM-MS20 SQ-Flow-KSM-MS25 SQ-Flow-KSM-PPA15 SQ-Flow-KSM-PPA20 SQ-Flow-KSM-PPA25 Description Flowmeter with brass flow tube DN20 Flowmeter with brass flow tube DN25 Flowmeter with PPA flow tube DN15 Flowmeter with PPA flow tube DN20 Flowmeter with PPA flow tube DN25 Document Change Control Version Date Change Preliminary Version Remark added regarding missing allowance for food safety and drinking water Change of article name Still preliminary version Remark: This flowmeter cannot be used in applications which require allowance for food safety or for drinking water. Rev.: 1.2 Seite 5 / 6

6 Copyrights & Disclaimer Copyright SonoQ GmbH, Sophie-Krämer-Str. 8, St. Ingbert, Germany-Europe. Trademarks Registered. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. Devices sold by SonoQ GmbH are covered by the warranty and patent indemnification provisions appearing in its General Terms of Trade. SonoQ GmbH makes no warranty, express, statutory, implied, or by description regarding the information set forth herein. SonoQ GmbH reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with SonoQ GmbH for current information. This product is intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by SonoQ GmbH for each application. This product is provided by SonoQ GmbH AS IS and any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are disclaimed. SonoQ GmbH shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of SonoQ GmbH rendering of technical or other services. Preliminary product information describes a product which is not in full production so that full information about the product is not yet available. Therefore, SonoQ GmbH ( SonoQ ) reserves the right to modify this product without notice. SonoQ GmbH Sophie-Krämer-Str St. Ingbert info@sonoq.de Sales in Germany, Austria and Switzerland IS-LINE GmbH Edisonstr Unterschleißheim Tel.: +49 (0) 89 / Fax.: +49 (0) 89 / info@is-line.de Rev.: 1.2 Seite 6 / 6