Elcometer ISO Groove Depth Checker. Operating Instructions

Transcription

1 Elcometer 2060 English ISO Groove Depth Checker Operating Instructions

2 English The Elcometer 2060 ISO Groove Depth Checker has been tested in accordance with EU regulations governing electro-magnetic compliance and meets the required directives. Note: Gauge readings may be affected if the unit is operated within a radio frequency electromagnetic strength of greater than 3 V/m. is a registered trademark of Elcometer Instruments Ltd. All other trademarks acknowledged. Copyright Elcometer Instruments Ltd All rights reserved. No part of this Document may be reproduced, transmitted, transcribed, stored (in a retrieval system or otherwise) or translated into any language, in any form or by any means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written permission of Elcometer Instruments Ltd. Doc.No. TMA-0366 Issue 01 Text with Cover No: 19809

3 CONTENTS Section Page 1 About your depth checker Using your instrument Connecting to a PC Maintenance Technical specification Accessories Related equipment

4 Thank you for your purchase of this Elcometer 2060 ISO Groove Depth Checker. Welcome to Elcometer. Elcometer are world leaders in the design, manufacture and supply of inspection equipment for coatings and concrete. Our products cover all aspects of coating inspection, from development through application to post application inspection. The Elcometer 2060 is a world beating product. With the purchase of this gauge you now have access to the worldwide service and support network of Elcometer. For more information visit our website at 1 ABOUT YOUR DEPTH CHECKER The Elcometer 2060 ISO Groove Depth Checker is a precision instrument used to determine the accuracy of fineness of grind gauges in accordance with ISO standards. The instrument is set to zero and then placed on the fineness of grind gauge with the measuring needle resting on the bottom of the tapered groove. The depth of the groove at that point is shown on the display. Three readings are taken to provide an average depth at each graduation point along the tapered groove. The average depth must not differ by more than 3 µm (0.12 mils) from the nominal value at each graduation point. 1.1 STANDARDS The Elcometer 2060 ISO Groove Depth Checker can be used in accordance with the following standards: DIN EN ISO NF ISO

5 1.2 WHAT THE BOX CONTAINS Elcometer 2060 ISO Groove Depth Checker Glass zero plate Storage case Calibration certificate Digital gauge instructions a Operating instructions The Elcometer 2060 ISO Groove Depth Checker is packed in a cardboard and foam package. Please ensure that this packaging is disposed of in an environmentally sensitive manner. Consult your local Environmental Authority for further guidance. To maximise the benefits of your new Elcometer 2060 ISO Groove Depth Checker please take some time to read these Operating Instructions. Do not hesitate to contact Elcometer or your Elcometer supplier if you have any questions. a. The instruction leaflet provided by the manufacturer of the digital gauge explains how to fit the battery and other features and functions of the digital gauge. 3

6 PRESET R TOL. 2 USING YOUR INSTRUMENT When using the instrument, take care not to damage the V-shaped edge of the rule or the surface of the glass zero plate. When taking a measurement, always hold the instrument by the plastic thermal insulation strips either side of the rule. 2.1 ZERO THE INSTRUMENT 1. Press the ON/OFF button to switch on the instrument. 2. Place the glass zero plate on a flat surface. 3. Hold the instrument on the glass plate perpendicular to the surface of the glass. 4. Press the ZERO button and check that the display shows ZERO/ABS 0.000mm ON/OFF 4

7 R 2.2 TAKING A READING 1. Having set the instrument to zero, place the instrument on the surface of the fineness of grind gauge at the deepest end. 2. Align the measuring needle with a graduation mark on the scale of the fineness of grind gauge and the centre line of the groove (position B). 3. Check that the instrument is perpendicular to the surface of the fineness of grind gauge with the measuring needle touching the bottom of the tapered groove. 4. Record the depth of the groove from the display. 5. Repeat steps 1 to 4 above at each side of the groove (positions A and C). 6. Calculate the average of the three readings. When taking a reading, always hold the gauge here. If the average groove depth differs by more than 3 µm (0.12 mils) from the nominal value at the graduation point, the fineness of grind gauge is faulty and must be repaired or replaced. 7. Repeat steps 1 to 6 above at each graduation point of the fineness of grind gauge. 2.3 AFTER USE When you have finished taking readings, replace the instrument and glass zero plate in the protective case provided. ZERO/ABS A 0.030mm PRESET B Fineness of Grind Gauge TOL. C ON/OFF 5

8 3 CONNECTING TO A PC Your gauge can be connected to a PC to allow measurement data to be saved as it is collected. To connect to a PC, the following accessories will be required: Computer connection cable Dataputer 1CHM Multiplexer (Signal converter) DATA-XL software See Accessories on page 7 for ordering information. 4 MAINTENANCE The Elcometer 2060 ISO Groove Depth Checker is designed to give many years reliable service under normal operating and storage conditions. Regular calibration checks over the life of the gauge are a requirement of quality management procedures e.g. ISO 9000 and other standards. For checks and certification contact Elcometer or your local Elcometer supplier. Details of Elcometer offices around the world are given on the outside cover of these Operating Instructions. Alternatively visit the Elcometer website, 6

9 5 TECHNICAL SPECIFICATION Range: 0 mm to 6.48 mm (0" to 0.26") Resolution: 1 µm (0.04 mils) Accuracy: 3 µm (0.12 mils) Width of 60 mm (2.36") measuring edge: Battery: 1.5 V, SR44 button cell b 6 ACCESSORIES The following optional items are available from your local supplier or direct from Elcometer: Computer connection cable: KT002060P004 Dataputer 1CHM Multiplexer: M001CHM (Signal converter) DATA-XL software: M500DXL b. Batteries must be disposed of carefully to avoid environmental contamination. Please consult your local environmental authority for information on disposal in your region. Do not dispose of any batteries in fire. 7

10 7 RELATED EQUIPMENT In addition to the Elcometer 2060 ISO Groove Depth Checker, Elcometer produces a wide range of other equipment for measuring the physical characteristics of surface coatings. Users of the Elcometer 2060 may also benefit from the following Elcometer products: Elcometer 2000 Muller Laboratory Grinder Elcometer Fineness of Grind Gauges Elcometer Viscosity Cups and Rotational Viscometers For further information contact Elcometer, your local supplier, or visit our website at 8