Coast Guard Navigation Standards Manual

Transcription

1 January 2012 Coast Guard Navigation Standards Manual

2 Commandant nd Street, S.W. Stop 7357 United States Coast Guard Washington, D.C Staff Symbol: CG-7511 Phone: (202) Fax: (202) COMDTCHANGENOTE JAN2013 COMMANDANT CHANGE NOTICE 3530 CANCELLED: 22JAN2014 Subj: CH-1 TO COAST GUARD NAVIGATION STANDARDS MANUAL, COMDTINST M3530.2D Ref: (a) COMDT(CG-01) memo 5102 of 27 Apr 09 (b) COMDT(CG-NAV-1) memo 3530 of 20 Nov PURPOSE. This Commandant Change Notice publishes change one to the Coast Guard Navigation Standards Manual, COMDTINST M3530.2D. 2. ACTION. All Coast Guard unit commanders, commanding officers, officers-in-charge, deputy/assistant commandants, and chiefs of headquarters staff elements shall comply with the provisions of this Commandant Change Notice. Internet release is authorized.. 3. DIRECTIVES AFFECTED. With the addition of this Commandant Change Notice, the Coast Guard Navigation Standards Manual, COMDTINST M3530.2D, is updated. 4. MAJOR CHANGES. This change adds Chapter 1.B.4. regarding tactical/high-speed boat maneuvering, and updates Chapter 2.D.3. adding the Wide Area Augmentation System (WAAS) as an accepted GPS augmentation system. 5. DISCUSSION. This change to the Coast Guard Navigation Standards is based upon paragraph 5.A.7. of reference (a), directing the development of policy on the employment of tactical maneuvering, including high-speed maneuvering, by Coast Guard boats, and reference (b) which requested a change to the policy on accepted GPS augmentation systems. DISTRIBUTION-SDL No. 162 a b c d e f g h i j k l m n o p q r s t u v w x y z A X X X X X X X X X X X X X X X X X X B C X X X X X X X X X X X D X X X E F G H X X NON-STANDARD DISTRIBUTION:

3 6. DISTRIBUTION. No paper distribution will be made of this change. An electronic version will be located on the Coast Guard Directives System (CGDS) sites located at: Internet: Intranet: and CG Portal: 7. PROCEDURES. Remove and replace the following sections of the Coast Guard Navigation Standards Manual, COMDTINST M3530.2D: Remove Page 1-5, 1-6 Page 2-1, 2-2 Replace Page 1-5, 1-6 Page 2-1, DISCLAIMER. This document is intended to provide operational requirements for Coast Guard personnel and is not intended to, nor does it, impose legally-binding requirements on any party outside the Coast Guard. 9. RECORDS MANAGEMENT CONSIDERATIONS. This Commandant Change Notice has been thoroughly reviewed during the directives clearance process, and it has been determined there are no further records scheduling requirements, in accordance with Federal Records Act, 44 U.S.C et seq., NARA requirements, and Information and Life Cycle Management Manual, COMDTINST M (series). This policy does not have any significant or substantial change to existing records management requirements. 10. ENVIRONMENTAL ASPECT AND IMPACT CONSIDERATIONS. a. The development of this Commandant Change Notice and the general policies contained within it have been thoroughly reviewed by the originating office in conjunction with the Office of Environmental Management, and are categorically excluded (CE) under current USCG CE # 33 from further environmental analysis, in accordance with Section 2.B.2. and Figure 2-1 of the National Environmental Policy Act Implementing Procedures and Policy for Considering Environmental Impacts, COMDTINST M (series). Because this Commandant Change Notice contains guidance on, and provisions for, compliance with applicable environmental mandates, Coast Guard categorical exclusion #33 is appropriate. b. This directive will not have any of the following: significant cumulative impacts on the human environment; substantial controversy or substantial change to existing environmental conditions; or inconsistencies with any Federal, State, or local laws or administrative determinations relating to the environment. All future specific actions resulting from the general policies in this Commandant Change Notice must be individually evaluated for compliance with the National Environmental Policy Act (NEPA), DHS and Coast Guard NEPA policy, and compliance with all other environmental mandates. Due to the administrative and procedural nature of this Commandant Change Notice, and the environmental guidance provided within it for compliance with all applicable environmental laws prior to promulgating any directive, all applicable environmental considerations are addressed appropriately in this Commandant Change Notice.

4 11. FORMS/REPORTS. None. Mark E. Butt /s/ Rear Admiral, U.S. Coast Guard Assistant Commandant for Capability

5 Commandant nd Street, S.W. Stop 7357 United States Coast Guard Washington, D.C Staff Symbol: CG-7511 Phone: (202) Fax: (202) COMMANDANT INSTRUCTION M3530.2D COMDTINST M3530.2D 27 JAN 2012 Subj: Ref: COAST GUARD NAVIGATION STANDARDS MANUAL (a) United States Coast Guard Regulations 1992, COMDTINST M (series) (b) Cutter Training and Qualification Manual, COMDTINST M (series) (c) U.S. Coast Guard Boat Operations and Training (BOAT) Manual, Volume I, COMDTINST M (series) (d) U.S. Coast Guard Boat Operations and Training (BOAT) Manual, Volume II, COMDTINST M (series) (e) Operational Risk Management, COMDTINST (series) (f) U.S. Navy Ship Control and Navigation Personnel Qualification Standard (PQS), NAVEDTRA (series) (g) Cutter Organization Manual, COMDTINST M (series) (h) Personnel Qualification Standard (PQS) Officer of the Deck (OOD), COMDTINST M (series) (i) Information and Life Cycle Management Manual, COMDTINST M (series) (j) Procedures for the Preparation and Disposition of Cutter Logs, COMDTINST M (series) 1. PURPOSE. This Manual promulgates navigation policies and procedures for all cutters, cutter boats and shore based boats. A B C D E F G H DISTRIBUTION-SDL No. 158 a b c d e f g h i j k l m n o p q r s t u v w x y z * NON-STANDARD DISTRIBUTION: *Dl: CGLO ATG MAYPORT (2), CGLO ATG DET NORFOLK (2), CGLO ATG PEARL HARBOR (2), CGLO ATG PAC SAN DIEGO (2), CGLO ATG EVERETT, WA (2) U.S. NAVY DISTRIBUTION: COMNAVSURFLANT (4), COMNAVSURFPAC (4), COMTRALANT (4), COMTRAPAC (4), FTC NORFOLK (4), NWTC CHARLESTON (4), FTC MAYPORT (4), FTU LITTLE CREEK (4), FTC PEARL HARBOR (4)

6 2. ACTION. All Coast Guard unit commanders, commanding officers, officers-in-charge, deputy/assistant commandants, and chiefs of headquarters staff elements shall comply with the provisions of this Manual. Internet release is not authorized. 3. DIRECTIVES AFFECTED. Coast Guard Navigation Standards, COMDTINST C is hereby cancelled. 4. DISCUSSION. Navigation remains a critical basis for all underway operations and a fundamental competency. This manual is designed to assist the CO/OINC, Navigator and Coxswain in carrying out their responsibilities as outlined in Coast Guard Regulations. New updates leverage the proven reliability of internationally accepted electronic navigation systems while retaining the capability to fix position using visual lines of position and radar ranges. 5. PROCEDURES. Official distribution will be via the Coast Guard Directive (CGDS) DVD. An electronic version will be located on the following Information and Technology CG-612 web sites. Intranet: Internet: and CGPortal: 6. MAJOR CHANGES. a. Chapter 1 additions: (1) Commanding Officers/ Officers-in-Charge shall promulgate Command Navigation Standards within 90 days of assuming command. Portions of this manual now pertain to all cutters. (2) Conduct a steering test and propulsion check prior to entering restricted waters or getting underway IAW reference (a). (3) All Cutters will maintain proficiency in paper plot as a tertiary backup mode of navigation. (4) Command Navigation Standards shall include: (a) Definition of shoal water and method to indicate shoal water for each navigational system as well as on paper charts. (b) Method of indicating that electronic tracklines are properly reviewed and approved, (i.e. ALL CAPS once approved). (c) Specific guidance pertaining to electronic chart displays, including filters. (d) Specific onboard chart hierarchy (Additional Cutter Items). (e) Ship s characteristics and tactical data (Additional Cutter Items). (f) Gyro error frequency determination (relocated from C, 3.A.3). (g) AIS settings and use policy. 2

7 (h) Electronic casualty control. (i) Requirements for logging propulsion and steering mode (relocated from C, 9.C). (j) GPS to antenna offset settings. (k) Drag and swing circle procedures for electronic charts. (l) Radar configurations with inputs specified. b. Chapter 2. Additions: (1) Preparations; verifying all positioning sources for accuracy. (2) Position comparisons, clarification. (3) DR Clarification. (4) Fix labeling and set and drift standards (relocated from C, 3.A 5 and 3.A.6). (5) Navigation report information (relocated from C, 1.B.2.g). (6) Authorization for use of WAAS on GPS receivers. c. Chapter 3. Additional Requirements for Boat Navigation (relocated from C ch. 4). d. Chapter 4. Electronic Navigation Systems (relocated from C ch. 5). (1) Addition: (a) Restricting applications on situational awareness computers. (b) Clarification on ECINS/ECS use. (c) Policy on Personal Navigation Applications (APPs). e. Chapter 5. Electronic Chart Data (relocated from C ch. 6). (1) Updated to allow the use of Digital Navigation Charts in all waters not covered by NOAA. f. Chapter 6. Celestial Navigation (relocated from C ch. 7). g. Chapter 7. Navigation Planning and Briefs (relocated from C ch. 8) (1) Additions: (a) Includes sections of C ch. 3. (b) Chart preparation section, broken down into electronic and paper chart requirements. 3

8 (c) Additional requirements for navigation briefs. h. Chapter 8. Cutter Logs, Records and Checklists (relocated from C ch. 9) (1) Additions: (a) Updated ECINS use guidelines to include fluxgate compass. (b) Additional guidelines for Deviation Tables and use of fluxgate compasses. i. Chapter 9. Anchoring (new chapter) j. Enclosure (3). Cutter Navigation Teams (1) Updated requirement for secondary Navigation Team in CIC/CSC. 7. REQUESTS FOR CHANGES. Change recommendations should be routed in writing via the chain of command to Commandant (CG-751) for cutters and Commandant (CG-731) for shore based boats. 8. ENVIRONMENTAL ASPECT AND IMPACT CONSIDERATIONS. Environmental considerations were examined in the development of this manual and were determined to be not applicable. 9. FORMS/ REPORTS. The forms referenced in this Manual are available in USCG Electronic Forms on the Standard Workstation or on the Internet: ; CGPortal at and Intranet at The Ship s Position Log, OPNAV-3100/3; Standard Bearing Book, OPNAV-3530/2; and Navy Navigation Workbook, OPNAV-3530/1 are only available through the Navy at Click on Forms from the menu and do a keyword search using the form number. Vincent B. Atkins /s/ Rear Admiral, U. S. Coast Guard Assistant Commandant for Capability 4

9 RECORD OF CHANGES CHANGE NUMBER DATE OF CHANGE DATE ENTERED BY WHOM ENTERED CH-1 JAN2013 COMDT(CG-751) COMDT(CG-751)

10 This Page Intentionally left blank

11 CHAPTER 1. COMMANDING OFFICER/ OFFICER-IN-CHARGE A. Responsibilities All Units B. Command Navigation Standards All Units Additional Cutter Items Additional Shore-based Boat Force Unit Items Units performing tactical/high speed boat operations 1-4 CHAPTER 2. GENERAL NAVIGATION REQUIREMENTS A. Purpose B. Discussion..2-1 C. Preparations D. Positioning Sources Category I Category II GPS Corrections E. Fixes Precautions a. Reducing speed as appropriate b. Take all way off c. Increase fix frequency d. Turning away from the danger Electronic Paper Erasures Intervals Verification F. Charts Electronic Charts Paper Charts G. Navigating with Paper Charts Set and Drift Estimated Position Dead Reckoning Navigation Reports Report information CHAPTER 3. ADDITIONAL REQUIREMENTS FOR BOAT NAVIGATION A. General Paper chart fixes Dead Reckoning Boat s Position B. Restricted Waters Paper chart fixes Precautions i

12 C. Boats Equipped with Scalable Integrated Navigation System (SINS)/Electronic Charting System (ECS) D. Additional Requirements for Non-standard Boat (NSB) Operations.3-1 CHAPTER 4. ELECTRONIC NAVIGATION SYSTEMS A. Coast Guard Electronic Navigation Systems General Restricting Applications Personal Navigation Applications 4-1 B. Electronic Charting and Integrated Navigation System (ECINS) General General ECINS Usage System usage in Restricted Waters C. Electronic Chart System (ECS) ECS Usage by Cutters ECS Usage by Boats D. Scalable Integrated Navigation System (SINS) for Boats SINS Usage CHAPTER 5. ELECTRONIC CHART DATA A. General Data Licensing Discrepancies. Rendering, loading and B. Approved Electronic Chart Data Electronic Navigational Charts (ENC) Digital Nautical Charts Raster Navigational Chart Commercial products C. Up-To-Date Electronic Chart Data Full file Official updates Manual NOAA Updates Scalable Integrated Navigation System (SINS) D. Recommended Electronic Chart Type Hierarchy E. Electronic Chart Data Selection Render Coverage Scale Up-to-date Scale/ Up-to-date F. Electronic Chart Data Scaling Viewing Display matching G. Notes on Electronic Chart Data Use ii

13 1. Vector vs. Raster Charts Chart Symbology Situational awareness use CHAPTER 6. CELESTIAL NAVIGATION General A. Proficiency Cutter class Proficient Opportunities Training B. Requirements Documentation Computer computations Chronometers CHAPTER 7. NAVIGATION PLANNING AND BRIEFS A. Navigation Planning Purpose Reference Publications B. Chart Preparations Paper Chart Preparations Electronic charts preparations C. Navigation Briefs Required information D. Boat Crew Briefs Requirements Debriefs CHAPTER 8. CUTTER LOGS, RECORDS AND CHECKLISTS A. General B. Electronic Logs ECINS use Compass Checks and Deviation Tables Maintenance C. Deck Logs D. Ship Position Log E. Standard Bearing Book Chart number Time zone and date Radar ranges Soundings Bearings Abbreviations Gyro/Radar error Navigation aids F. Navy Navigation Workbook iii

14 1. Computer computations STELLA Strip forms Calculator use G. Combat Information Center (CIC)/Combat Support Center (CSC) Navigation Log Page labeling Fix recording Securing the log Radar ranges Abbreviations Navigation aids H. Captain s Night Orders I. Checklists J. Record Retention Claim Litigation Investigation.8-4 CHAPTER 9. ANCHORING A. General B. Proficiency Cutter class Proficient Opportunities C. Requirements Documentation Calculations Navigation Team Responsibilities APPENDIX A. APPENDIX B. GLOSSARY OF TERMS... A-1 LIST OF ACRONYMS... B-1 ENCLOSURES (1) Navigation Plotting Symbols (2) Line Handling Commands (3) Cutter Navigation Teams. (4) Helm Commands (5) ECINS and Paper Chart Use Flow Chart (6) Guidance For Boat Forces Units Command Navigation Standards (7) Sample Getting Underway Checklist (8) Sample Entering Port/Approaching Restricted Waters Checklist FIGURES 2-1 Positioning Source Hierarchy 5-1 Electronic Chart Type Hierarchy iv

15 CHAPTER 1. COMMANDING OFFICER/ OFFICER-IN-CHARGE A. Responsibilities. Commanding Officers/ Officers-in-Charge (CO/OICs) shall: 1. All Units. a. Ensure compliance with the provisions of this Manual. (NOTE: COs/OICs of WLI, WLR, WLIC and WYTL class cutters, due to their unique areas of responsibility, missions, navigation techniques, and the lack of accurate charts that portray the ever-changing bottom contours of these areas, shall tailor the requirements discussed in section 1.B.2.e and Chapters 4, 5, and 8 of this manual, as appropriate, for incorporation into their Command Navigation Standards.) b. Promulgate Command Navigation Standards within 90 days of assuming command. Prior navigation standards shall remain in effect until superseded. c. Assign, train, and certify navigation personnel in accordance with references (a) through (d) as appropriate. d. Incorporate the principles of effective risk assessment into navigational planning in accordance with reference (e). The risk assessment process may be tailored to be consistent with the complexity of the specific mission, but should not omit any step in the process. e. Conduct navigation exercises in accordance with reference (b) and/or (d). f. Designate a Navigator in accordance with reference (a). Cutters that do not have an Operations Officer assigned shall designate an experienced underway Officer of the Deck that is an Officer, Chief, or Petty Officer who possesses the required proficiency, training, maturity, and judgment required of this position. The Navigator shall complete applicable parts of reference (f). Schools listed in reference (f) are recommended but not required. g. Conduct a steering test and propulsion check prior to entering restricted waters or getting underway in accordance with reference (a). h. Maintain proficiency of basic navigation skills (paper plot) through training and practice. i. Ensure Navigation Teams maintain a thorough understanding of principles of operation, use, and most importantly, limitations of installed equipment. j. Shall approve all tracklines and routes (Cutters only). The OOD retains discretion to maneuver as necessary in accordance with the promulgated Command Navigation Standards. 1-1

16 B. Command Navigation Standards. CO/ OICs shall publish Command Navigation Standards that incorporate the navigation requirements detailed in reference (a) and this Manual. Command Navigation Standards shall, at a minimum, include: 1. All Units. a. Navigational draft. b. Definition of shoal water and method to indicate shoal water for each navigational system as well as on paper charts. (1) Safety Depth (2) Safety Contour (3) Depth Below Keel c. Command definitions of Navigational Zones (i.e. Areas that require specific levels of attention to and frequency of navigational tasks). Navigational Zones shall be based on the vessel s navigational draft, mission, operating environment, etc. Navigational Zones shall include: (1) Restricted Waters (i.e. Harbor, Harbor Approach, Near Coastal) (2) Coastal. (3) Open Ocean. (4) Any additional zones required by specific operating environments or operational circumstances. d. Standard navigational fix intervals for each Navigational Zone. e. The interval at which the primary positioning source must be compared to an unrelated positioning source and logged (i.e. radar overlay, chart matching, Vis/Radar LOP (see chapter 2.C.5)). This shall be done at least every third fix in Restricted Waters and in all other waters, at least once per day. f. Standard navigation plotting symbols. Enclosure (1) may be used for this purpose, either in its entirety, or tailored at command discretion. g. Alarm management. The conditions when an alarm may be silenced or disabled shall be addressed. The modern bridge may have more than 50 audible and/or visible alarms, warnings, and indicators available to help ensure safe operations. h. Standard line handling commands. Enclosure (2) may be used for this purpose in its entirety or tailored at command discretion. 1-2

17 i. Method of indicating that electronic tracklines on all systems are properly reviewed and approved (i.e. trackline name in ALL CAPS once approved) before being put in use. Additionally, all tracklines on all systems must be identical with any offset issues resolved at the Navigation Brief stage. j. Specific guidance pertaining to electronic chart displays, including filter settings and scaling below base scale, when deemed unavoidable. 2. Additional Cutter Items. a. Specific guidance concerning navigation of the cutter s boat(s) while operating independently of the cutter. For these standards, independently means the boat coxswain, not the bridge watch, is entirely responsible for the boat s safe navigation (i.e. Over the Horizon/out of the cutter s active sensor range). b. Specific Navigation Team manning requirements for navigating with electronic navigation systems and/or paper charts for each navigational zone. Standard Navigation Team positions are listed in Enclosure (3). c. Standard helm and engine order commands (see Enclosure (4). d. Special Sea Detail, Anchoring and Mooring Bills in accordance with reference (g) and relevant sections of this Manual. e. A list of paper charts required to be onboard, further annotated to reflect those charts designated by the CO/OIC to be up-to-date through the latest Local Notice to Mariners. Follow the decision matrix in Enclosure (5) to determine paper chart carriage requirements. f. Any deviation from this manual s recommended electronic chart data hierarchy (see Chapter 5.B). g. In addition to the Navigational Draft, the following ship s characteristics shall be specified: (1) Full load draft. (2) Masthead height. (3) Length overall. (4) Length along the waterline. (5) Distance from hawsepipe to alidade. (6) Distance from hawsepipe to GPS antenna. (7) Distance from hawsepipe to stern. (8) Distance from GPS antenna to stern. 1-3

18 (9) Distance from radar antenna to stern. (10) Distance from radar antenna to hawsepipe. h. Ship s unclassified tactical data, including tactical and final diameter in accordance with Chapter 4 of reference (a). Pertinent data must be posted at all conning stations while underway. i. Determine gyro error prior to getting underway or entering restricted waters. If conditions permit, gyro error shall be determined at least once daily while underway. When gyro error is obtained, gyrocompass(es) and repeaters shall be compared and errors posted and entered into electronic navigation systems. j. AIS settings and use policy to include setting transmit modes as well as ship s status (i.e. restricted maneuverability, anchored, underway, etc.). k. Electronic casualty control procedures to include responses to loss of gyro or GPS input. l. When navigating with automatic ship control systems such as autopilot or Dynamic Positioning System, the mode in use must be logged. Additionally, the propulsion mode shall be logged. m. GPS to antenna offset settings during normal steaming, anchoring, ATON or other applicable evolutions. n. Drag and swing circle procedures for electronic charting systems. o. Standard heading and speed input configuration for the radar. p. Cross track warning and alarm settings for each navigational zone. q. Conditions under which CIC (if applicable) would take control of the primary plot. 3. Additional Shore-based Boat Force Unit Items. a. A list of paper charts, including the unit s Area of Responsibility (AOR) that must be ready and up-to-date through the latest Local Notice to Mariners. These charts will be carried on each assigned boat or in the unit navigation kit. Commands may require each coxswain to maintain their own copies of up-to-date ready charts. b. Key operating areas. c. Principle navigation routes, tracklines and standard waypoints. d. Areas within the unit s AOR where boat crews shall conduct frequent area familiarization transits in accordance with reference (d). e. Areas within the unit s AOR that pose significant navigational or environmental risks to boats. These areas shall also be displayed on a chart in the operations/ 1-4

19 planning space. f. Specific operating guidance such as speed limits, safe operating distances from known hazards, frequency of fixes, and restricting operating areas for specific boat types. An example of unit level guidance is provided in Enclosure (6). g. Navigation and piloting requirements for use during surf operations (i.e. Use of natural ranges, radar ranges, waypoints, etc.). h. Requirements for maintaining Dead Reckoning plots based on boat type, navigational systems, and operating environments. 4. Units performing tactical/high speed boat operations a. CO/OICs shall describe conditions under which the use of high speed and specialized tactics is appropriate within the Command Navigation Standards (shore-based) or Cutter Organization Manual (cutters) for both operations and training. The following minimum topics shall be covered: (1) A "continuum of tactics" that provides a range of responses from officer presence through deadly force in accordance with the Maritime Law Enforcement Manual, COMDTINST M (series). (2) Implications and mitigation of risk and appropriate response to the threat environment. (3) Application and limits for training as well as appropriate tactics for normal operations (operations in the absence of articulated threats). 1-5 CH-1

20 This page intentionally left blank 1-6 CH-1

21 CHAPTER 2. GENERAL NAVIGATION REQUIREMENTS A. Purpose. This section sets forth minimum navigational requirements for all Coast Guard cutters and boats. (NOTE: WLI, WLR, WLIC and WYTL class cutters, while operating on rivers and the Intracoastal Waterways, are exempt from the specific requirements of this section. COs/OICs of these units shall tailor the requirements of this chapter, as appropriate, for incorporation into their Command Navigation Standards). B. Discussion. Navigation is fundamental to safe operations afloat. These requirements reflect the proven reliability and accuracy of internationally accepted electronic navigation systems while retaining the capability to fix position using visual lines of position and radar ranges. Coast Guard cutters will normally use electronic navigation systems as their primary means of navigation. COs/OINCs shall train and practice basic navigation skills (Mode III, paper plot) as directed by reference (b) to maintain a contingency navigation capability. C. Preparations. Prior to getting underway, all positioning sources shall be verified for accuracy, including GPS, Shipboard infrared Visual Sensor System (SIRVSS), radar, and/or gyrocompass if applicable. D. Positioning Sources. Figure 2-1 is the hierarchy of various positioning sources. 1. Category I. Category I positioning sources are adequate for use as the primary source of own vessel s position while operating in all waters. 2. Category II. Category II positioning sources are not considered adequate for precise navigation and shall only be used as the primary source of the own vessel s position in open ocean. 3. GPS Corrections. The only Global Positioning System (GPS) corrections currently authorized for Coast Guard coastal and restricted waters navigational use are provided by the Differential GPS system and the Wide Area Augment System (WAAS). 4. GPS Receiver and WAAS. A unit equipped with a GPS receiver that is capable of receiving GPS corrections from the Wide Area Augmentation Systems (WAAS) is authorized to use this feature. WAAS is a satellite-based GPS augmentation system being implemented by the Federal Aviation Administration to support lateral and vertical navigation for all phases of flight in the US. However, WAAS is not yet an approved option for positioning ATON. 5. Position comparisons. When using any form of GPS as the primary source for positioning information, the position shall be compared to an unrelated positioning source at intervals prescribed i.e. radar overlay, chart matching, Vis/Radar LOP. Another GPS or DGPS unit does not meet this requirement. This shall be done once a day in Open Ocean and every third fix in Restricted Waters. Units shall comply as capabilities allow. When navigating in Open Ocean, comparing GPS to a celestial observation once a day will meet this requirement. Only the units listed in Chapter 6 of this manual are required to maintain proficiency in celestial navigation. 2-1 CH-1

22 POSITIONING SOURCE HIERARCHY CATEGORY I GPS with DGPS corrections or WAAS-enabled GPS PPS (Precise Positioning Service) Classified System, if applicable GPS SPS (Standard Positioning System (see note 1) Visual and/or RADAR (includes Radar or Chart Matching) CATEGORY II Inertial Navigation System Celestial Figure 2-1 Note 1: Use of GPS SPS as a Category I positioning source assumes that Selective Availability (SA), an intentional offset induced into GPS, is set to zero. At the time of this manual s promulgation, SA is set to zero. However, personnel involved with navigation must be aware that DoD may select signal degradation regionally using SA or other tactics. Therefore, cutters deploying abroad may require the use of PPS or other enhancements to ensure accurate fix information is being received. When intentional GPS signal degradation such as SA is being used, SPS shall be considered a Category II source, not adequate for navigation in Harbor, Harbor Approach, Near Coastal and other restricted waters. E. Fixes. 1. Precautions. Cutters shall use all available data such as soundings, danger ranges/bearings, set and drift, and proximity to aids to navigation to fix the vessel s position and improve on the DR plot. At any time fix quality comes into question, particularly while operating in restricted waters, the following actions may be deemed appropriate depending on prevailing conditions: a. Reducing speed as appropriate. b. Take all way off. c. Increase fix frequency. d. Turning away from the danger. 2. Electronic. An electronically provided position when displayed on a chart from an adequate positioning source, as defined in Section C of this chapter, constitutes a fix. This includes radar or chart matching capability. 3. Paper. The intersection of lines of position (LOP) from at least three prominent points of land, fixed, and/or celestial objects with a separation of 15 degrees or greater. a. When using relative bearings, a minimum of two visual LOPs and one radar range shall be used as capabilities allow. b. When three LOPs are not simultaneously available, advancing LOPs to a common time to create a running fix may be used. 2-2 CH-1

23 c. Fixes will be labeled with the time and proper symbol. 4. Erasures. Fixes shall not be erased or deleted because they appear in error; rather, another fix shall be taken immediately to ascertain the vessel s position. 5. Intervals. The ship s position shall be fixed at an interval that ensures safe navigation with due regard to the proximity of shoal water, weather conditions, and mission, not to exceed one hour. 6. Verification. Fixes shall be verified by all means including, in no particular order: a. Soundings b. Aids to Navigation (ATON) c. Radar or other electronic means d. Seaman s eye F. Charts. All charts used shall be of the best scale available for the circumstance. The best scale may not always be the largest available scale, depending on navigational and operational requirements. 1. Electronic Charts. Prior to use, electronic charts must be up-to-date in accordance with Chapter 5.C of this Manual. 2. Paper Charts. Only up-to-date charts produced by an approved IHO will be used with priority given to NOAA and NGA. Paper charts are considered to be up-to-date if they are both the most current edition and corrected up to the latest Local Notice to Mariners, Weekly Notice to Mariners, and Broadcast Notice to Mariners. 3. Allowances. Review chart and publication requirements and allowances annually, and provide any requests for new products or allowance changes via the Chain of Command. Register/update unit contact information in the Account Management and Provisioning System (AMPS) annually or as account point of contact changes, whichever is sooner. G. Navigating with Paper Charts. 1. Set and Drift. a. If fix interval is three minutes or greater, set and drift shall be determined at every fix. b. If fix interval is less than three minutes, set and drift shall be determined every second fix. c. Set and drift shall be applied to subsequent DR positions to determine an EP in the event that planned fixes are not obtained. d. When unable to maintain a steady course (i.e. vessel traffic avoidance becomes an 2-3

24 issue), set and drift will be determined upon the second fix after it again becomes possible to maintain a steady course. 2. Estimated Position. An estimated position (EP) is a Dead Reckoning position modified by additional information, which in itself is insufficient to establish a fix. a. Verification. EPs shall be compared by using the available means listed in 2.C Dead Reckoning. A DR will be properly labeled and track projected for at least two fix intervals. A properly maintained DR is the foundation for maintaining an acceptable estimate of the ships position between fixes. The following are general rules used in constructing and maintaining the Navigator s plot. a. Plot a DR position at least every hour on the hour in open ocean. b. Plot a DR position at every course change. c. Plot a DR position at every speed change. d. Plot a DR position when obtaining a fix or running fix. e. Plot a DR position when obtaining a single line of position. f. A new course line shall be plotted from each fix or running fix. 4. Navigation Reports. At each fix interval, the Navigation Evaluator shall provide a navigation report to the Conning Officer, as required by the Command Navigation Standards. 5. Report information. Navigation reports shall be provided when using paper charts or an electronic charting system. These reports may include: a. Fix time. b. Fix type (and quality, as appropriate). c. Fix position in relation to proposed track. d. Report CIC/CSC concurs, does not concur, or has no fix (if applicable). e. Any recommendation to regain/maintain proposed track. f. Nearest hazard to navigation. g. Next aid to navigation. h. Distance to next turn. i. Time to next turn and turn bearing/range. j. Course after next turn. 2-4

25 k. Set and drift (as required). l. Depth of water beneath the keel and comparison to charted depth. m. Other pertinent information. 2-5

26 This page intentionally left blank 2-6

27 CHAPTER 3. ADDITIONAL REQUIREMENTS FOR BOAT NAVIGATION A. General. This section applies to all shore based small boats and cutter boats operating outside the direct sight of the cutter. 1. Paper chart fixes. When navigating with paper charts, fixes shall be plotted no more than 30 minute intervals. Fixes may be timed to coincide with OPS/position reporting to the Operational Commander. Fixes shall become more frequent whenever the coxswain is operating in an unfamiliar area and during periods of restricted visibility. 2. Dead Reckoning. Maintain a Dead Reckoning plot as required by the Command Navigation Standards. 3. Boat s Position. Any time the coxswain is uncertain of the boat s position, the coxswain shall take all way off or anchor if necessary until the boat s position can be fixed. B. Restricted Waters. 1. Paper chart fixes. When navigating within restricted waters designated by the CO/OIC, using paper charts, a fix shall be plotted at least every fifteen minutes. 2. Precautions. Coxswains transiting close to navigation hazards and shoals, during restricted visibility or darkness, or operating in an unfamiliar area shall operate the vessel with extreme caution, which may include: a. Coordinating the boat crew as a navigation team to specifically observe the compass heading, fathometer, radar, electronic navigation systems, or otherwise augment the Coxswain s navigational ability. b. Reducing speed as appropriate for prevailing circumstances. c. Take all way off as appropriate for prevailing conditions to review the navigational picture. d. Utilize navigational data such as soundings, danger ranges, or bearings to verify position. e. Increase fix frequency. C. Boats Equipped with Scalable Integrated Navigation System (SINS)/Electronic Charting System (ECS). The following boats are not required to place fixes on a paper chart unless specifically stated in Command Navigation Standards: 1. Boats using SINS or ECS with an adequate primary positioning source (electronic positionfixing system) and an up-to-date electronic chart. D. Additional Requirements for Non-Standard Boat (NSB) Operations. At a minimum, CO/OIC shall ensure NSBs (not including work/flood punts and ice skiffs) have the capability to obtain a fix by electronic means (i.e. handheld or installed GPS, radar, chart plotter, etc.) excluding personal navigation applications that use cellular/gps technology. (See paragraph 4.A.3.) 3-1

28 This page intentionally left blank 3-2

29 CHAPTER 4. ELECTRONIC NAVIGATION SYSTEMS A. Coast Guard Electronic Navigation Systems. 1. General. The Coast Guard has three general classifications of systems that are authorized for use as the primary means of navigation as prescribed in this Manual. Each system has its own unique capabilities and limitations. The type of system(s) installed varies by platform throughout the Coast Guard. a. Electronic Charting and Integrated Navigation System (ECINS) b. Electronic Chart System (ECS) c. Scalable Integrated Navigation System (SINS) 2. Restricting Applications. On computers designated specifically for navigation or situational awareness, only the navigation program should be open. There shall be no other application window open on a designated navigation computer while underway. 3. Personal Navigation Applications. The use of personal navigation applications (APPs) using cellular/gps technology is not approved for navigation aboard Coast Guard assets. B. Electronic Charting and Integrated Navigation System (ECINS). 1. General. The Coast Guard employs several ECINS that are intended to meet or to exceed international requirements for Electronic Chart Display and Information Systems (ECDIS) and ECS, but include some deliberate additions to, and deviations from, the standards governing those systems. 2. General ECINS Usage. a. ECINS may be used as the primary means of navigation in lieu of paper charts if the following conditions are met: (1) An adequate primary positioning source (see figure 2-1) is in use. (2) Approved up-to-date electronic chart data as described in Chapter 5 is in use. (3) Adequate back-up arrangements are available including: a. Back-up Positioning Source. A positioning source from the same category as the primary positioning source that does not rely on any elements in common with the primary positioning source (e.g., a second GPS/DGPS receiver is not an adequate back-up positioning source for a GPS/DGPS receiver). Examples of adequate backup positioning sources for GPS/DGPS include visual and/or radar lines of position 4-1

30 entered into ECINS or radar/chart matching on ECINS. b. Back-up Arrangements. Adequate back-up arrangements shall enable the continuous operation of essential ECINS functions during a failure of the ECINS to ensure that a failure does not result in a potentially dangerous situation. This includes a timely transfer of route monitoring functions within one fix interval. b. Enclosure (5) outlines paper chart carriage requirements while using ECINS as the primary means of navigation. c. In the case of failure of the primary electronic positioning source, where the ECINS is otherwise fully functional, it shall be possible to navigate using other available positioning sources with the ECINS. The cutter navigation team shall maintain proficiency in manually entering visual and radar LOPs. This is Mode II navigation as defined in this manual s glossary. 3. System usage in Restricted Waters. This section establishes additional requirements while transiting in or near restricted waters. a. Compare the primary positioning source to a back-up positioning source at least every third fix. b. Maintain echo-sounding (i.e. fathometer) alarm on control unit or ECINS. C. Electronic Chart System (ECS). The Coast Guard employs ECS that are based upon recognized requirements, but include some deliberate additions to the international standards governing those systems. 1. ECS Usage by Cutters. An ECS is primarily used as a situational awareness tool, but may be also used in the following manner: a. ECS may be used as the primary means of navigation in open ocean in lieu of paper charts if the following conditions are met: (1) An adequate primary positioning source (see figure 2-1) is in use. (2) Approved up-to-date electronic chart data as described in Chapter 5 is in use. (3) An appropriate portfolio of paper charts is available to transfer the primary navigation plot to paper within one fix interval. (4) An ECINS is not available. b. ECS may be used as a backup arrangement to ECINS if the following conditions are met: (1) An adequate primary positioning source (see figure 2-1) is in use. 4-2

31 (2) Approved up-to-date electronic chart data as described by Chapter 5 is in use. (3) The planned route from the ECINS is in use on the ECS. (4) ECS meets requirements of 4.B.3. while in restricted waters. (5) Up-to-date paper charts * available for route transfer within one fix interval while in restricted waters. (* Per Command Navigation Standards) 2. ECS Usage by Boats. ECS may be used as the primary means of navigation in all waters if the following conditions are met: a. An adequate primary positioning source (see figure 2-1) is in use. b. Approved up-to-date electronic chart data as described in Chapter 5 is in use. c. Coxswain observes radar, fathometer, visual ranges, and ATON in order to verify the displayed position. d. Command promulgated standard waypoints and routes are used. (NOTE: Not required for cutter boats.) e. Up-to-date paper charts are onboard to transfer the primary navigation plot to paper within one fix interval. (NOTE: Not required for cutter boats.) D. Scalable Integrated Navigation System (SINS) for Boats. The Coast Guard employs SINS that are intended to meet international requirements for small craft radar. SINS include additional chart plotting and limited navigational functionality. but do not meet standards for ECS. 1. SINS Usage. SINS may be used as the primary means of navigation in all waters on boats if the following conditions are met: a. An adequate primary positioning source (see figure 2-1) is in use. b. Approved up-to-date electronic chart data as described in Chapter 5 is in use. c. Up-to-date paper charts are onboard to transfer the primary navigation plot to paper within one fix interval. d. Command promulgated standard waypoints and routes are used. e. Coxswain observes radar, fathometer, visual ranges, and ATON in order to verify the displayed position. f. Depth alarms are set to the navigational draft. 4-3

32 g. Cross Track Error alarm is enabled when navigating to a waypoint. h. Radar and electronic chart data are displayed at all times. i. An ECS is not available for use. 4-4

33 CHAPTER 5. ELECTRONIC CHART DATA A. General. 1. Data. Electronic charts consist of chart data that has been specifically developed for presentation on electronic navigation systems. 2. Licensing. Licensing agreements associated with procured electronic chart data must be followed and data sharing is not authorized. 3. Discrepancies. Chart Rendering, chart disk loading, and discrepancies in chart data for foreign waters shall be reported to the Navigation Center via priority message to COGARD NAVCEN ALEXANDRIA VA//NIS//. For ATON discrepancies on charts covering US waters, units shall ensure the appropriate district (dpw) office is notified via priority message traffic. B. Approved Electronic Chart Data. The Coast Guard has approved the following electronic chart data for use with electronic navigation systems: 1. Electronic Navigational Charts (ENC). Official Electronic Navigation Charts (ENC) produced or issued by or on the authority of a government authorized hydrographic office. Note: ENC produced and certified under NOAA s Certified NOAA ENC Value Added Distributor (CEVAD) program are official data. 2. Digital Nautical Charts. Digital Nautical Charts (DNC) are produced and issued by the National Geospatial-Intelligence Agency (NGA). DNC are published in general, coastal, approach, and harbor libraries. These libraries may not correspond directly with Command definitions of Navigational Zones contained in the Command Navigation Standards. DNC are updated monthly via VDU (Vector Data Update) patch provided on CD through NGA automatic distribution or by download directly from the NGA web-site. These charts have since been updated monthly using ALL available information provided by worldwide Official Hydrographic Offices. Like all charts, including paper, the data is only as accurate and timely as the host countries Hydrographic Office. Over dependence on navigation systems and data is an ever-present hazard, the best information lies in the buoy line and should be used with caution until the information has been verified. NGA paper charts are derived from the same database and the importance of reporting inaccuracies cannot be overstated. 3. Raster Navigational Chart. An official Raster Navigation Chart (RNC) produced or issued by or on the authority of a government authorized hydrographic office. 4. Commercial products. Commercial vector and/or raster charts procured by or through the Coast Guard Electronic Chart Manager. C. Up-To-Date Electronic Chart Data. An Electronic Chart is considered up-to-date if it has been corrected within the last forty-five days. The approved methods are: 5-1

34 1. Full file. Full file replacement of the electronic chart data (e.g. cell, library, chart, or chartlet). 2. Official updates. Applying official updates (e.g. ENC updates, Vector Product Format (VPF) Database Updates, or raster updates (patches)). 3. Manual. Manual corrections, using information provided by: a. The cognizant hydrographic office (e.g. National Oceanic and Atmospheric Administration (NOAA), US Army Corps of Engineers (USACE), National Geospatial- Intelligence Agency (NGA), Canadian Hydrographic Services (CHS), United Kingdom Hydrographic Office (UKHO) etc.) b. Local Notice to Mariners. c. Broadcast notifications (e.g. Broadcast Notice to Mariners, HYDROLANTS, etc.) Note: Limited temporary corrections may be manually entered into the electronic navigation system. 4. NOAA Updates. Weekly updated ENC and RNC are available for free download by district or state from NOAA s ENC mirror site. NOAA applies updates weekly to the ENCs and RNCs on this site. It is highly recommended cutters download fresh charts prior to getting underway and as often as connectivity allows. NOAA ENC Mirror Site NOAA RNC Mirror Site 5. Scalable Integrated Navigation System (SINS). a. For SINS equipped vessels, an electronic chart is considered up-to-date if it has been corrected or replaced within six months of a permanent chart change. b. Upon notification of a temporary or permanent chart correction, SINS may continue to be used as primary means of navigation if the temporary or permanent chart corrections are manually entered. In cases where the temporary or permanent chart correction cannot be manually entered, SINS may continue to be used as the primary means of navigation if an up-to-date paper chart is out and being used in conjunction with SINS. D. Recommended Electronic Chart Type Hierarchy. Navigators shall consult the latest chart advisories provided by the Electronic Chart Manager. The following recommended hierarchy (Figure 5-1) is intended to aid with the chart selection process. Variances are allowed at the discretion of the CO/OIC, provided they are spelled out in the Command Navigation Standards. 5-2

35 Official ENC DNC Waters not covered by NOAA Official RNC Commercial Vector Chart Commercial Raster Chart (i.e. Caribbean and Central America Data) Figure 5-1 E. Electronic Chart Data Selection. For electronic navigation systems that render multiple chart products, selecting the appropriate electronic chart product is based upon several factors. The following steps are intended to help with the selection process: 1. Render. Determine what type of data the system can render. 2. Coverage. Determine the available coverage for the area of operations. In U.S. coastal waters, NOAA data shall take precedence. In U.S. inland waters (Western Rivers), United States Army Corps of Engineers data shall take precedence. 3. Scale. Select the best scale chart product for that area and for the mission being conducted. 4. Up-to-date. Of the available chart products, determine which are up-to-date. 5. Scale/ Up-to-date. Scale and most up-to-date must be weighed together in determining the best chart for navigation. F. Electronic Chart Data Scaling. 1. Viewing. Electronic chart data is most accurately viewed when displayed at its source scale. Scaling/zooming in or out will distort the visually perceived relative distance between chart objects. In addition, cursor-indicated positions for charted features vary when scaling the chart. 2. Display matching. When radar and electronic chart data are presented together on the same display, the display shall match in scale, orientation and projection. Scaling out the Radar to 24 nm for example, when the electronic chart is scaled to only 3 nm can cause misinterpretations. Display Matching and Chart Matching are not the same, Chart Matching is a positioning source, Display Matching is not. G. Notes on Electronic Chart Data Use. 1. Vector vs. Raster Charts. a. Vector Charts. ENC and DNC are vector charts. In vector chart data, the real world is portrayed as charted objects that are represented by lines, points, polygons (areas), and text. This representation is described by attributes and coordinates in a database. This database can be queried and used for such functions such as anti-grounding alerts. 5-3