B787-8 AIRCRAFT WEIGH WORKSHEET
|
|
- Rodger Stevens
- 6 years ago
- Views:
Transcription
1 WEIGHING FACILITIES AND EQUIPMENT ITEM MECH INSP The airplane should be weighed inside a closed facility that will: Exclude all wind and drafts. Permit shutdown of air conditioning during the weighing operation. Maintain a relatively constant temperature. Provide a level weighing surface and sufficient overhead clearance. The required equipment for weighing an airplane consists of: Certified electronic or mechanical weighing equipment. Plumb bob PREPARATION FOR AIRPLANE WEIGHING The airplane configuration is of extreme importance in the derivation of a defined airplane operating weight from an actual scale weight. The interior and exterior of the airplane must be as complete as possible. All fluid levels (fuel, oil, water, hydraulic) must be known quantities. The weighing area and equipment usage must be controlled to avoid errors and minimize variation in scale readings. 1 Fuel Fuel from all tanks is drained to the trapped (usable and unusable) fuel condition. Trapped fuel is defined as the quantity of fuel which cannot be removed through the production sump tank drains. To obtain trapped fuel condition: (a) Pump off all usable fuel to sump level, REF AMM TASK DMC-B787-A B-221A-A. (b) Adjust and maintain airplane attitude at 0.8 degrees nose down (±0.1 degree) longitudinal and 0.0 degrees (±0.1 degree) lateral. (c) Drain the remaining fuel through sump drain valves, REF AMM TASK DMC- B787-A A-221A-A. 2 System Fluids System fluids must be drained or at a known quantity as follows: (a) Drain all waste tanks, REF AMM TASK DMC-B787-A A-200A-A. (b) Drain to empty the potable water system, REF AMM TASK DMC- B787-A A-228A-A. FORM No: ISSUE: 03 Page 1 of 6
2 ITEM MECH INSP 2 The following systems must be serviced for flight: (c) Engine Oils, REF AMM TASK DMC-B787-A B-200A-A. (d) Hydraulic Fluids, REF AMM TASK DMC-B787-A E-369A-A. (e) Oxygen, REF AMM TASK DMC-B787-A C-200A-A. (f) Main Landing Gear Oleo Oil, REF AMM DMC-B787-A (g) Nose Landing Gear Oleo Oil, REF AMM DMC-B787-A (h) Fire extinguisher charge, REF AMM DMC-B787-A Airplane Configuration The condition of the airplane at the time of weighing must be one that is well defined and can be easily repeated. Each of the following steps must be completed prior to weighing: (a) Inventory the airplane using the applicable Configuration and Safety Equipment Drawings listed in CATP 15, Configuration Manual. Record any missing items on the table provided on page 6, and hi-light these to the aircraft weigher prior to weighing the aircraft. (b) Remove all shop equipment, tools, and trash. (c) Stow all loose equipment items in their proper locations. (d) Dry the airplane thoroughly. (e) Close all doors and access panels. (f) Retract the flaps fully. (g) Set the horizontal stabilizer, control surfaces, and spoilers to their neutral positions. (h) Inflate landing gear tires to specified operating pressures, REF AMM TASK DMC- B787-A A-200A-A. FORM No: ISSUE: 03 Page 2 of 6
3 ITEM WEIGHING OPERATION MECH INSP The airplane should be weighed in a level longitudinal attitude when possible. If the airplane cannot be leveled for weighing, the longitudinal attitude must be within + or - 2 degrees from level during the actual weighing operation, and the measured center of gravity must be arithmetically corrected to an equivalent level center of gravity. This requires application of the correction factors from TABLE 1 (Non-Level Weighing). The recommended method of determining the longitudinal attitude of the aircraft is to attach a plumb bob to the plumb bob fitting located in the left main gear wheel well and to read the longitudinal attitude from the corresponding scale. 4 WEIGHING PROCEDURE USING PLATFORM SCALES Carry out aircraft weighing as directed by Weighing Engineer, using the following procedure:- The following procedure outlines the method for weighing the airplane on portable or floor level platform scales. The scales may be mechanical beam or electronic. Follow weighing equipment manufacturer's operating instructions. (a) The balance arm for the nose gear when using platform scales is B.A (b) To obtain the balance arm location of the main gear, it is necessary to measure the main landing gear oleo extension since the balance arm of the weight reaction point varies with the extension of the oleo strut (Refer to Figure 1 JACK POINT BALANCE ARMS VERSUS OLEO EXTENSION). (c) Follow weighing equipment manufacturer s operating instructions. (d) Zero the platform scales prior to putting the airplane on the scales. All undesirable tare should be off the scales. (e) Position the airplane on the scales. The approach should be straight and the airplane should be brought slowly and smoothly to a stop, without applying airplane brakes. (f) Inflate or deflate landing gear oleos as required to obtain the desired longitudinal attitude. Check the attitude with the plumb bob. (g) Record landing gear oleo extensions. (h) Record weight reading obtained from each airplane weight reaction point. (i) Remove the airplane from the scales. (j) Check the scales for zero load condition. (k) Repeat weighing procedure as needed to verify airplane weight. FORM No: ISSUE: 03 Page 3 of 6
4 NON-LEVEL WEIGHING When the airplane is weighed in a non-level condition, the calculated C.G. must be corrected to the level condition. The attitude of the airplane must be known at the time of weighing. Determine the C.G. of the airplane in this non-level condition, and then use the following tables to correct the C.G. to the level condition. TABLE 1 Non-Level Weighing Example An airplane weighed in a 1-1/2 degree tail down attitude has a calculated, non-level C.G. at B.A IN. Applying the C.G. correction of -3.8 inches (from the table) gives the level attitude C.G. at IN. FORM No: ISSUE: 03 Page 4 of 6
5 JACK POINT BALANCE ARMS VERSUS OLEO EXTENSION The following main landing gear figure shows how to determine the amount of oleo extension (Dimension A ). The corresponding chart diagrams the relationship between the main landing gear forward and aft axle jack point balance arms and the main landing gear oleo extension (Dimension A ). FIGURE 1 FORM No: ISSUE: 03 Page 5 of 6
6 MISSING ITEMS RECORD ITEM DESCRIPTION POSITION QUANTITY This task was carried out and completed in accordance with the requirements of the MOE, Part 2, Section Maint. Organisation Approval Ref: PRINT NAME: DATE: SIGNATURE: STAMP: The Stamp/Signature in inspection Column denotes work has been carried out in accordance with the above certification. FORM No: ISSUE: 03 Page 6 of 6
BOEING AIRCRAFT WEIGH WORKSHEET
WEIGHING FACILITIES AND EQUIPMENT ITEM MECH INSP The airplane should be weighed inside a closed facility that will: Exclude all wind and drafts. Permit shutdown of air conditioning during the weighing
More informationWeighing your Seabee
Weighing your Seabee Note: The following procedure must be supervised and signed off by a qualified A&P and the final paperwork must be included in the Aircraft Records. The actual weights must be included
More informationAIRCRAFT PRIMARY CONTROLS A I R C R A F T G E N E R A L K N O W L E D G E
1.02.02 AIRCRAFT PRIMARY CONTROLS 1. 0 2 A I R C R A F T G E N E R A L K N O W L E D G E CONTROLLING AIRCRAFT AIRCRAFT CONTROL SYSTEM In general, we use control inputs of the following devices in cabin:
More informationWIPLINE 3450 SEAPLANE FLOATS
FOUND SUPPLEMENT M400-S08 Transport Canada Approved Flight Manual Supplement For WIPLINE MODEL 3450 SEAPLANE FLOATS This supplemental manual is applicable to Wipline Model 3450 seaplane float equipped
More informationFire Apparatus Operator: ARFF
Fire Apparatus Operator: ARFF Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/ Operator Professional Qualifications, 2017 Edition. Alabama Fire College November 26, 2018 Alabama
More informationFire Apparatus Operator Aircraft Rescue and Fire Fighting
Fire Apparatus Operator Aircraft Rescue and Fire Fighting Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/ Operator Professional Qualifications, 2014 Edition. Alabama Fire College
More informationAEROCET 3400 AMPHIBIOUS FLOATS
FOUND SUPPLEMENT M400-S10 Transport Canada Approved Flight Manual Supplement For AEROCET MODEL 3400 AMPHIBIOUS FLOATS This supplemental manual is applicable to Aerocet Model 3400 amphibious float equipped
More informationTECHNIQUES FOR OFF AIRPORT OPERATIONS
Off Airport Ops Guide TECHNIQUES FOR OFF AIRPORT OPERATIONS Note: This document suggests techniques and procedures to improve the safety of off-airport operations. It assumes that pilots have received
More informationCSSna HIAWK FLOATPLANE WNER'S MANUAL SUPPLEMENT D CES-100-3/73
CSSna HIAWK FLOATPLANE WNER'S MANUAL SUPPLEMENT D709-13-CES-100-3/73 2220 108 PERFORMANCE - SPECIFICATIONS FLOATPLANE 1620ft 148 GROSS WEIGHT lbs SPEED: Top Speed at Sea Level mph u Cruise, 75% Power at
More informationFLIGHT MANUAL SUPPLEMENT
FLIGHT MANUAL SUPPLEMENT HUSKY / RF 8001 SKIS This supplement is valid for The Husky A-1. The following derivates of the Husky may use this Supplement after the approval of a minor change to operate the
More informationANNEX TO TYPE CERTIFICATE No. ULL - 07 / 2003 a
Letecká amatérská asociace ČR, Light Aircraft Association CR Ke Kablu 289, 102 00 Praha 10, Hostivař tel: sekretariát 271 085 270 fax: 27 10 85 596 e-mail: laacr@laacr.cz http://www.laacr.cz Type certificate
More informationFAA-S-ACS-6 June 2016 Private Pilot Airplane Airman Certification Standards. Task ACS Settings
FAA-S-ACS-6 June 2016 Private Pilot Airplane Airman Certification Standards Cessna 172: mixture rich, carb heat out if below the green arc. Clearing Turns all manuevers! Task ACS Settings Traffic Pattern
More informationBrief Maintenance Manual DAR-Solo
Brief Maintenance Manual DAR-Solo Sofia 2009 Page: 1 TABLE OF CONTENTS Introduction 3 Limitations and safety information 4 General view of DAR-Solo prototype 7 Technical Data 8 Inspection before and after
More informationGeneral. Procedure Checklists. Emergency Procedures. FSD Aerostar 700P Superstar
General The recommended procedures for coping with various types of emergencies and critical situations are provided in this section. These procedures are suggested as a course of action for coping with
More informationSUPPLEMENT SEPTEMBER 2010 HIGH ALTITUDE TAKEOFF AND LANDING (ABOVE 14,000 FEET PRESSURE ALTITUDE) MODEL AND ON 68FM-S28-00 S28-1
MODEL 680 680-0001 AND ON HIGH ALTITUDE TAKEOFF AND LANDING (ABOVE 14,000 FEET PRESSURE ALTITUDE) COPYRIGHT 2010 CESSNA AIRCRAFT COMPANY WICHITA, KANSAS, USA 15 SEPTEMBER 2010 S28-1 SECTION V - SUPPLEMENTS
More informationII.E. Airplane Flight Controls
References: FAA-H-8083-3; FAA-8083-3-25 Objectives Key Elements Elements Schedule Equipment IP s Actions SP s Actions Completion Standards The student should develop knowledge of the elements related to
More informationLOAD CHARTS RT540E 85% STABILITY ON OUTRIGGERS 75% STABILITY ON RUBBER
LOAD CHARTS RT540E 85% STABILITY ON OUTRIGGERS 75% STABILITY ON RUBBER SERIAL NUMBER 1 2 TABLE OF CONTENTS GENERAL NOTES... 4 WT. REDUCTIONS / LINE PULLS & REEVING INFO / HOIST PERFORMANCE. 5 LIFTING AREA
More informationEmergency Vehicle Driver
Emergency Vehicle Driver Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/Operator Professional Qualifications, 2014 Edition. Alabama Fire College February 2016 0 /09/2017 Alabama
More informationBASIC AIRCRAFT STRUCTURES
Slide 1 BASIC AIRCRAFT STRUCTURES The basic aircraft structure serves multiple purposes. Such as aircraft aerodynamics; which indicates how smooth the aircraft flies thru the air (The Skelton of the aircraft
More informationAS0403 Aircraft Systems & Instruments G.Mahendra Perumal
AS0403 Aircraft Systems & Instruments G.Mahendra Perumal Assistant Professor Department of Aerospace Engineering School of Mechanical Engineering SRM University, Chennai, India. Email: aeromahendra@gmail.com
More informationApparatus Driver/Operator Evaluation Form Rosenbauer Tanker:
Section I: Apparatus Knowledge The Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus. 1. The Apparatus Driver/Operator demonstrates
More informationChapter 3: Aircraft Construction
Chapter 3: Aircraft Construction p. 1-3 1. Aircraft Design, Certification, and Airworthiness 1.1. Replace the letters A, B, C, and D by the appropriate name of aircraft component A: B: C: D: E: A = Empennage,
More informationThe Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus.
Section I: Apparatus Knowledge The Evaluator shall ask the Apparatus Driver/Operator questions regarding the mechanical systems and size of the apparatus. 1. The Apparatus Driver/Operator demonstrates
More informationGarbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028. Name Date Signature. Author Jarred Hearle 30/11/2014. Reviewed John Nulty 30/11/2014
Garbex Drum Crusher Safe Work Procedure PTES_HSE_SWP_028 Name Date Signature Author Jarred Hearle 30/11/2014 Reviewed John Nulty 30/11/2014 Approved Geoff Selfe 01/12/2014 Key Safety Acts Complete a 5
More informationB737-3/4/5 CFM56 MAINTENANCE PRACTICE TRAINING MANUAL B1/B2 LEVEL
MAINTENANCE PRACTICE TRAINING MANUAL LEVEL DERICHEBOURG ATIS Aéronautique - ATIS Aviation, 17, Avenue Didier Daurat 31700 Blagnac : 05 34 60 61 40 - : 05 34 60 61 50 DOC.FOR.14 Ed3 1/38 TRAINEE SURNAME:
More informationSPH 4C Unit 4 Hydraulics and Pneumatic Systems
SPH 4C Unit 4 Hydraulics and Pneumatic Systems Properties of Fluids and Pressure Learning Goal: I can explain the properties of fluids and identify associated units. Definitions: Fluid: A substance that
More informationCessna 152 Standardization Manual
Cessna 152 Standardization Manual This manual is to be utilized in conjunction with the manufacturers approved POH/ AFM and the Airplane Flying Handbook (FAA-H-8083-3A). This manual should be used as a
More informationApparatus Operator/Pumper
Skill Number: AOP-1 Operate Fixed Systems Objective: 4.3.7 (A) (B) 1. The candidate shall be provided with the equipment to complete this objective including apparatus. 2. The candidate uses safety precautions.
More informationService Call: Vacuum Prevention System Testing on Category A and B Aerial Devices. Tools Required: 1. Atmospheric Vent Test Set (P/N )
Service Call: Vacuum Prevention System Testing on Category A and B Aerial Devices Tools Required: 1. Atmospheric Vent Test Set (P/N 488180) *An automotive vacuum test kit with various fittings to hook
More informationCommercial Maneuvers for PA28RT-201
Commercial Maneuvers for PA28RT-201 Cruise checklist: Power 23'', 2400 RPM (23, 24) Lean mixture Fuel Pump Off (Check positive fuel pressure) Landing light Off Pre-Maneuver Checklist in the Takeoff configuration
More informationON-DECK TRIP: Charter Boat Check-Out/Check-In Form
Charter Boat Check-Out/Check-In Form TRIP: Skipper: Phone: Boat Type & Size: Boat Name: Draft: Beam: Mast Height: Water: Cap. Gal. in tank(s) Waste: Cap. Gal in tank(s) Fuel: Cap. Gal THIS FORM IS FOR
More informationCover Page for Lab Report Group Portion. Head Losses in Pipes
Cover Page for Lab Report Group Portion Head Losses in Pipes Prepared by Professor J. M. Cimbala, Penn State University Latest revision: 02 February 2012 Name 1: Name 2: Name 3: [Name 4: ] Date: Section
More informationILS APPROACH WITH A320
1. Introduction ILS APPROACH WITH A320 This document presents an example of an Instrument landing system (ILS) approach performed with an Airbus 320 at LFBO airport runway 32 left. This document does not
More informationTheory of Flight Aircraft Design and Construction. References: FTGU pages 9-14, 27
Theory of Flight 6.01 Aircraft Design and Construction References: FTGU pages 9-14, 27 Main Teaching Points Parts of an Airplane Aircraft Construction Landing Gear Standard Terminology Definition The airplane
More informationINSTRUCTIONS FOR CONTINUED AIRWORTHINESS AND EQUIPMENT MAINTENANCE MANUAL FOR OXYGEN BOTTLE MOUNT
HELIFAB 1318 SMEDE HWY. BROUSSARD, LA 70518 REPORT NUMBER THIS MANUAL IS PREPARED TO PROVIDE INFORMATION, INSTRUCTIONS FOR CONTINUED AIRWORTHINESS, MAINTENANCE INSTRUCTIONS AND REPAIR PROCEDURES FOR EQUIPMENT
More informationMarine Safety Center Technical Note
Marine Safety Center Technical Note MARINE SAFETY CENTER TECHNICAL NOTE (MTN) NO. 1-17 MTN 1-17 16715 December, 2017 Subj: GUIDANCE ON DESIGN VERIFICATION FOR SUBCHAPTER M TOWING VESSELS Ref: (a) Navigation
More informationCompiled by Matt Zagoren
The information provided in this document is to be used during simulated flight only and is not intended to be used in real life. Attention VA's - you may post this file on your site for download. Please
More informationColorado Division of Fire Prevention & Control Driver Operator Pumper JPRs (NFPA 1002, 2014 Edition)
Colorado Division of Fire Prevention & Control Driver Operator Pumper JPRs ( Edition) JPR # Task Initial Certification JPR Requirement: 15 Mandatory Renewal JPR Requirement: 100% of All JPRs (including
More informationC-130 Reduction in Directional Stability at Low Dynamic Pressure and High Power Settings
C-130 Reduction in Directional Stability at Low Dynamic Pressure and High Power Settings The C-130 experiences a marked reduction of directional stability at low dynamic pressures, high power settings,
More informationBeechcraft Duchess 76 Maneuver Notes
Beechcraft Duchess 76 Maneuver Notes I. Maneuver notes for Performance (AOA V), Slow Flight and Stalls (AOA VIII), Emergency Operations (AOA X), and Multiengine Operations (AOA XI) a. Maneuvers addressed:
More informationState of Oregon Department of Public Safety Standards and Training. Driver Task Book. Task Book Assigned To:
State of Oregon Department of Public Safety Standards and Training Driver Task Book Task Book Assigned To: Name DPSST Fire Service # Department Name Date Initiated Signature of Department Head or Training
More informationGrove TMS800E Product Guide
Grove TMS0E Product Guide Features 12,6 m - 39 m (41 ft - 128 ft) four-section full power MEGAFORM boom 10 m 17 m (33 ft 56 ft) manual offset bifold swingaway 2 x 20 ft intermediate lattice inserts 10
More informationV mca (and the conditions that affect it)
V mca (and the conditions that affect it) V mca, the minimum airspeed at which an airborne multiengine airplane is controllable with an inoperative engine under a standard set of conditions, is arguably
More informationCessna 172S Skyhawk Standardization Manual
Cessna 172S Skyhawk Standardization Manual This manual is to be utilized in conjunction with the manufacturers approved POH/ AFM and the Airplane Flying Handbook (FAA-H-8083-3A). This manual should be
More informationLesson: Pitch Trim. Materials / Equipment Publications o Flight Training Manual for Gliders (Holtz) Lesson 4.4 Using the Trim Control.
11/18/2015 Pitch Trim Page 1 Lesson: Pitch Trim Objectives: o Knowledge o An understanding of the aerodynamics related to longitudinal (pitch) stability o Skill o Use of the pitch trim system to control
More informationKEY CONCEPTS AND PROCESS SKILLS. 1. Creating models is one way to understand and communicate scientific information.
Inside a Pump 21 40- to 1 50-minute session ACTIVITY OVERVIEW L A B O R ATO R Y SUMMARY In this activity, mechanical pumps serve as potential models for the human heart. In order to understand the working
More informationLinde Hydraulics Corporation, P.O. Box 82, Canfield, Ohio 44406
Page 1 / 5 BPV..HF with Pressure Cut-off BPV..EH with Pressure Cut-off PURPOSE The purpose of the "PRESSURE CUT-OFF" is to prevent large amounts of oil from bleeding over a relief valve, which reduces
More informationFire Apparatus Operator: Pumper
Fire Apparatus Operator: Pumper Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/Operator Professional Qualifications, 2014 Edition. Alabama Fire College February 2016 revised
More informationColorado Division of Fire Prevention & Control Driver Operator JPRs (NFPA 1002, 2014 Edition)
Colorado Division of Fire Prevention & Control Driver Operator JPRs ( Edition) JPR # Task Initial Certification JPR Requirement: 8 Mandatory Renewal JPR Requirement: 100% of All JPRs (including all subsections)
More informationLOAD CHARTS RT890E METRIC DIN / ISO / 75%
LOAD CHARTS RT89E METRIC DIN / ISO / 75% 232729 SERIAL NUMBER RT89E - S/N 232729 1 RT89E - S/N 232729 2 TABLE OF CONTENTS GENERAL NOTES...4 WEIGHT REDUCTIONS / LINE PULLS & REEVING INFO / RIGGING CHART
More informationROTORCRAFT FLIGHT MANUAL SUPPLEMENT. TO THE BELL MODEL UH-1H ROTORCRAFT FLIGHT MANUAL for the APICAL EMERGENCY FLOAT KIT
SUPPLEMENT TO THE for the APICAL EMERGENCY FLOAT KIT This supplement is to be used when the rotorcraft is modified by the installation of the Apical Float Kit 644.3201 for UH-1H helicopters. The information
More informationSwimming Pools, Hot Tubs and Spas
OLATHE FIRE DEPARTMENT BUILDING CODES 1225 S. Hamilton Circle Olathe, KS 66061 / Main: (913) 971-7900 / Fax: (913) 971-9812 Swimming Pools, Hot Tubs and Spas Definitions: Swimming Pool- Any structure intended
More informationOPERATION MANUAL DMI 16-LIGHT LIGHT TOWER ALSO AVAILABLE ONLINE AT DMI-LT.COM
OPERATION MANUAL DMI 16-LIGHT LIGHT TOWER ALSO AVAILABLE ONLINE AT DMI-LT.COM 1 You have purchased a very high quality piece of equipment that should provide years of useful life. Following the instructions
More informationHigh-Pressure Boiler Inspection Procedures: A Complete Checklist
High-Pressure Boiler Inspection Procedures: A Complete Checklist Inspecting high-pressure boilers is a complex process requiring preparation, planning, and a multitude of safety precautions. Regular inspections
More informationPhuel Modular Control Units
Phuel Modular Phuel Modular, like our market leading Modular BOPs, provide an efficient flexible solution to suit any customer s needs. Each unit is constructed from the best of materials and supportable,
More informationSingle Engine Complex Training Supplement PA28R-201 Piper Arrow III (Spring 2016 Revision)
Single Engine Complex Training Supplement PA28R-201 Piper Arrow III (Spring 2016 Revision) V-speed Quick Reference V-Speed KIAS Description Airspeed Indicator Marking VSO 55 Stall speed in landing configuration
More informationOIL SUPPLY SYSTEMS ABOVE 45kW OUTPUT 4.1 Oil Supply
OIL SUPPLY SYSTEMS ABOVE 45kW OUTPUT 4.1 Oil Supply 4.1.1 General The primary function of a system for handling fuel oil is to transfer oil from the storage tank to the oil burner at specified conditions
More informationChapter 2. Before You Get Underway. Copyright Coast Guard Auxiliary Association, Inc.
Chapter 2 Before You Get Underway 1 We ll Discuss: 1 Capacity 2 Float Plan 3 Pre-Departure Checks 4 Trailering & Fueling - Safety 5 Launching and Retrieving 6 Boat Maintenance 7 Boating Accessories 2 Capacity
More informationTechnical Knowledge and Aerostatics (Balloon) This syllabus presupposes a knowledge and understanding already attained at PPL level.
Subject No 29 Technical Knowledge and Aerostatics (Balloon) Note: This syllabus is primarily based on a balloon designed above 120000 cubic feet maximum. Each subject has been given a subject number and
More informationFire Apparatus Operator: Pumper
Fire Apparatus Operator: Pumper Skill Sheet Package Based on NFPA 1002: Standard on Fire Apparatus Driver/ Operator Professional Qualifications, 2017 Edition. Alabama Fire College August, 2018 revised
More informationCIVIL AIR PATROL United States Air Force Auxiliary Cadet Program Directorate. Cessna 172 Maneuvers and Procedures
CIVIL AIR PATROL United States Air Force Auxiliary Cadet Program Directorate Cessna 172 Maneuvers and Procedures This study guide is designed for the National Flight Academy Ground School. The information
More informationSAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT
SAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT SAMPLE WRITTEN PROGRAM The objective of this procedure is to establish a means of positive control to prevent the accidental starting
More informationOPERATION MANUAL NTF-15
OPERATION MANUAL NTF-15 Nitrogen Tire Filling Valve Stem Caps (Qty=200) Order P/N 436075 RTI Technologies, Inc 10 Innovation Drive York, PA 17402 800-468-2321 www.rtitech.com 035-81235-00 (Rev B) TABLE
More informationSTREAMLINE SHOP SERIES MODEL 30040V OPERATION & PARTS MANUAL
STREAMLINE SHOP SERIES MODEL 30040V OPERATION & PARTS MANUAL Sage Oil Vac 360 North Lakeside Drive Amarillo, TX 79118 phone: 806.372.7559 fax: 806.372.7565 1 2 1.1 WARRANTY SERVICE OR RETURNS Call 1-877-645-8227
More informationCranes and Hoists. Elevating Work Platforms ASSESSMENT
Cranes and Hoists Elevating Work Platforms ASSESSMENT Part 1 Part 2 Performance Oral/Written June 1995 Contents Page Assessor guidelines general guidelines for Schedule B i Part one Performance Assessment
More informationOPERATION MANUAL NTF-60 Plus
OPERATION MANUAL NTF-60 Plus Nitrogen Tire Filling Valve Stem Caps (Qty=200) Order P/N 436075 RTI Technologies, Inc 10 Innovation Drive York, PA 17402 800-468-2321 www.rtitech.com 035-81264-00 (Rev A)
More informationBugatti 100P Longitudinal Stick Forces Revision A
Bugatti 1P Longitudinal Stick Forces Revision A Stick-free static longitudinal stability (stick force-per-knot) and stick-free longitudinal maneuvering stability (stick force-per-g) were computed for the
More informationSECTION 1 - GENERAL SECTION 2 - LIMITATIONS SECTION 3 - EMERGENCY PROCEDURES
Beechcraft Bonanza Models. 35-33,35-A33,35-833,35-C33,35C33A, E33, E33A, E33C, F33, F33A. F33C, G33, A35, 835, C35, D35, E35, F35, G35,35R, H35, 535, K35, M35, N35, P35,S35, V35, V35A, V358,36, A36, A36TC
More informationSouthern Eagles Soaring
Southern Eagles Soaring N56LS Standard Cirrus Disassembly / Assembly Procedure. Version 2, 2017 You landed out so what now? First, hopefully you made arrangements with someone who has a hitch on their
More informationPOWER-OFF 180 ACCURACY APPROACH AND LANDING
POWER-OFF 180 ACCURACY APPROACH AND LANDING OBJECTIVE To teach the commercial student the knowledge of the elements related to a power-off 180 accuracy approach and landing. COMPLETION STANDARDS 1. Considers
More informationColumbia 300 (LC40-550FG) Information Manual Revison No. 2 (January 2003)
Columbia 300 (LC40-550FG) Information Manual Revison No. 2 (January 2003) THE INFORMATION IN THIS MANUAL WAS TAKEN DIRECTLY FROM THE FAA APPROVED AIRPLANE FLIGHT MANUAL. SINCE THE DATA IN THE LANCAIR COLUMBIA
More informationSTOL CH rd Edition Drawings, dated April 16, 2012 Summary of changes from Edition 2 Revision 1 to Edition 3.
STOL CH 750 3 rd Edition Drawings, dated April 16, 2012 Summary of changes from Edition 2 Revision 1 to Edition 3. Page Date Drawing Title 75-G-0 04/12 Three View Drawing 1. Edition 3 75-G-1 04/12 Drawings
More informationInspecting a motorsport vehicle during a competition
Unit 057 Inspecting a motorsport vehicle during a Level: 2 Credit value: 14 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to inspect
More informationDeccan Charters Private Limited
Work Order List Number / / Jul. / 2017. Report : Flying Hours updated till ( ), Last Done on ( 06-Jul-2017 ) & Work Order Number - For Next 400:00 Hours, 730 Days, 400 Cycles, 400 RINS, 400 Landings, As
More informationMaintenance Schedule for Gliders and Powered Gliders
Aircraft Mfr Model S/N Rego Total Hours Total Launches Engine Hours Date Inspecting Engineer GNZ Rating Job No Section 1: Required Documents, Manuals and Data 1.1 Documents Carried in Aircraft: DI Book
More informationVisualized Flight Maneuvers Handbook
Visualized Flight Maneuvers Handbook For High Wing Aircraft Third Edition For Instructors and Students Aviation Supplies & Academics, Inc. Newcastle, Washington Visualized Flight Maneuvers Handbook for
More informationNORMAL TAKEOFF AND CLIMB
NORMAL TAKEOFF AND CLIMB CROSSWIND TAKEOFF AND CLIMB The normal takeoff is one in which the airplane is headed directly into the wind or the wind is very light, and the takeoff surface is firm with no
More informationSERVICE BULLETIN. Service Bulletin Equipment Manufacturer Notification SB-ASTM-CTSW-99 SB-ASTM-CTLS-99 SB-ASTM-MC -99
Service Bulletin SERVICE BULLETIN Service Bulletin Equipment Manufacturer Notification SB-ASTM-CTSW-99 SB-ASTM-CTLS-99 SB-ASTM-MC -99 Repeating Symbols: Please pay attention to the following symbols throughout
More informationwww.guatemala-skies.com GUATEMALA GENERAL AVIATI INFORMATI TO GO Contents: Cessna 172 XP 1977 V Speeds & checklist Guatemala Radio Frequencies Emergency Transponder Codes & ATC Light Signals MGGT airport
More informationCertification Specifications for Normal, Utility, Aerobatic, and Commuter Category Aeroplanes CS-23
European Aviation Safety Agency Certification Specifications for Normal, Utility, Aerobatic, and Commuter Category Aeroplanes CS-23 20 July 2012 CS-23 Annex to ED Decision 2012/012/R PREAMBLE CONTENTS
More information1. Once you have completed the NAUI Scuba course, you will be qualified to
Chapter 1 1. Once you have completed the NAUI Scuba course, you will be qualified to 2. Most dives are easy. However, on every dive there is always a chance that you will need to exert yourself greatly.
More informationV.A. Preflight Inspection
References: AC 61-84; FAA-H-8083-3; FAA-H-8083-23; POH/AFM Objectives Key Elements Elements Schedule Equipment IP s Actions SP s Actions Completion Standards The student should develop knowledge of the
More informationPERFORM Operating Document
PERFORM Operating Document Use and Maintenance of CO 2 Incubator PC-POD-CA-007-v02 Revision History Version Reason for Revision Date 01 New POD 30-Sep-13 02 Minor revisions for section 2.3, 3.1, 4.3. 14-April-16
More informationAIRMOUNT VIBRATION ISOLATION
MOUNT VIBRATION ISOLATION SELECTION AND ISOLATION FORMULA Refer to the selection guide on page 33 for Airmount load and isolation capabilities. Follow this procedure: 1. LOAD CAPACITY Select one or two
More informationIdaho Fire Service Technology Pumping Apparatus Driver/Operator Skill Sheet: 1
Skill Sheet: 1 Standard 4.2.1, 4.2.2 Task: Perform and document routine test, inspection and servicing functions on specified systems and components. Performance Outcome: Given a fire department pumping
More informationExercise 2-2. Second-Order Interacting Processes EXERCISE OBJECTIVE DISCUSSION OUTLINE. The actual setup DISCUSSION
Exercise 2-2 Second-Order Interacting Processes EXERCISE OBJECTIVE Familiarize yourself with second-order interacting processes and experiment with the finer points of controller tuning to gain a deeper
More informationENERGY BLADE 3K4. Energy Blade Installation Instructions
ENERGY BLADE 3K4 Energy Blade Installation Instructions 1 Contents General information 2 Scope of these instructions 2 Product information 2 Designated use 3 Warranty 3 Safety instructions 4 Assembly and
More informationVortex Generator Installation Addendum
1 Introduction The Zlin Aviation, s.r.o. Kit, when installed in accordance with these instructions and other applicable data, results in better handling, a lower stall speed, and more controllable flare
More informationPL475. Patient Lift Scale. Owner's Manual
PL475 Patient Lift Scale Owner's Manual CARDINAL SCALE MFG. CO. 0046-M496-O1 Rev A PO BOX 151 WEBB CITY, MO 64870 Printed in USA 11/99 PH 417-673-4631 FAX 417-673-5001 2 Thank you for purchasing our DETECTO
More informationLicense to Keel Boat Manual
License to Keel Boat Manual BOAT CODE R32 SLIP C110 NOTE: SAIL IN REVERSE MAXIMUM CAPACITY: 8 PASSENGERS Violation Will Result In Suspension of Members Certification and Charter Privileges 110117 Table
More informationMyControl Bathing System Signature Series
MyControl Bathing System Signature Series Touch Assist Touch Pad and CM Technologies Seal Pressure Regulation Instructions Acceptable seal inflation pressure setting must be varified, and adjusted if necessary,
More informationGROVE MODEL RT58D - 20 TON CAPACITY
LIFTING CHARTS - Rough Terrain Cranes GROVE MODEL - 20 TON CAPACITY WEIGHT REDUCTIONS FOR LOAD HANDLING DEVICES 23 JIB with 28-70 BOOM * Stowed - 381 lbs. * Erected - 1,950 lbs. 23-38 TELE. JIB with 28-70
More informationFRESH AERO EasyLift System For Grumman AA-1 & AA-5 Series Aircraft. User Manual. Where Imagination Meets Innovation. The Steelebrook Group
FRESH AERO EasyLift System AA-1 & AA-5 Series Aircraft User Manual The Steelebrook Group Where Imagination Meets Innovation Thank you for purchasing the Fresh Aero EasyLift System for AA-1 & AA-5 series
More informationThe Discussion of this exercise covers the following points:
Exercise 5-3 Wet Reference Leg EXERCISE OBJECTIVE Learn to measure the level in a vessel using a wet reference leg. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Measuring
More information75 Ton SD Shop Press Operating Instructions
75 Ton SD Shop Press Operating Instructions MODEL NO. 856SD Hazard Symbols Used in the Manuals This manual includes the hazard symbols defined below when the operations or maintenance job involves a potential
More informationTecnam Eaglet Standard Operating Procedures and Maneuvers Supplement
Tecnam Eaglet Standard Operating Procedures and Maneuvers Supplement Normal Takeoff Flaps Take Off Trim set Fuel pump on Check for traffic Line up on white stripe Full power Stick should be located in
More informationXI.C. Power-Off Stalls
References: FAA-H-8083-3; POH/AFM Objectives Key Elements Elements Schedule Equipment IP s Actions SP s Actions Completion Standards The student should develop knowledge of stalls regarding aerodynamics,
More informationINSTRUCTOR GUIDE REFERENCES: PUMPING APPARATUS DRIVER/OPERATOR HANDBOOK, FIRST EDITION, IFSTA
TOPIC: RELAY PUMPING OPERATIONS LEVEL OF INSTRUCTION: TIME REQUIRED: ONE HOUR INSTRUCTOR GUIDE MATERIALS: APPROPRIATE AUDIO VISUAL SUPPORT REFERENCES: PUMPING APPARATUS DRIVER/OPERATOR HANDBOOK, FIRST
More informationPhuel Portable Control Units
Phuel Portable PCE Control Unit Pressure Test Unit c/w Chart Recorder Triple Wireline BOP The Phuel range of Air Driven Portable provide all the control functions required for well intervention operations
More informationIce Protection System
Cirrus Design Section 9 Pilot s Operating Handbook and FAA Approved Airplane Flight Manual Supplement for Ice Protection System When the Ice Protection System is installed on the Cirrus Design, this POH
More information